TI1 LM5576 Simple switcher 75 v, 3 a step-down switching regulator Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
LM5576/-Q1 SIMPLE SWITCHER® 75 V, 3 A Step-Down Switching Regulator
1 Features
3 Description
•
The LM5576 is an easy to use SIMPLE SWITCHER®
buck regulator which allows design engineers to
design and optimize a robust power supply using a
minimum set of components. Operating with an input
voltage range of 6 - 75 V, the LM5576 delivers 3 A of
continuous output current with an integrated 170 mΩ
N-Channel MOSFET. The regulator utilizes an
Emulated Current Mode architecture which provides
inherent line regulation, tight load transient response,
and ease of loop compensation without the usual
limitation of low-duty cycles associated with current
mode regulators. The operating frequency is
adjustable from 50 kHz to 500 kHz to allow
optimization of size and efficiency. To reduce EMI, a
frequency synchronization pin allows multiple ICs
from the LM(2)557x family to self-synchronize or to
synchronize to an external clock. The LM5576
ensures robustness with cycle-by-cycle current limit,
short-circuit protection, thermal shut-down, and
remote shut-down. The device is available in a power
enhanced HTSSOP-20 package featuring an
exposed die attach pad for thermal dissipation. The
LM5576 is supported by the full suite of WEBENCH®
On-Line design tools.
1
•
•
•
•
•
•
•
•
•
•
•
LM5576-Q1 is an Automotive Grade Product that
is AEC-Q100 grade 1 Qualified (−40°C to + 125°C
Operating Junction Temperature) and AEC-Q100
Grade 0 Qualified (−40°C to + 150°C Operating
Junction Temperature)
Integrated 75 V, 170 mΩ N-channel MOSFET
Ultra-Wide Input Voltage Range from 6 V to 75 V
Adjustable Output Voltage as Low as 1.225 V
1.5% (Q1) and 1.65% (Q0) Feedback Reference
Accuracy
Operating Frequency Adjustable Between 50 kHz
and 500 kHz with Single Resistor
Master or Slave Frequency Synchronization
Adjustable Soft-Start
Emulated Current Mode Control Architecture
Wide Bandwidth Error Amplifier
Built-in Protection
HTSSOP-20EP (Exposed Pad)
2 Applications
•
•
Automotive
Industrial
Device Information(1)
PART NUMBER
LM5576
LM5576-Q1
PACKAGE
BODY SIZE (NOM)
HTSSOP (20)
6.50 mm x 4.40 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Application Schematic
VIN
VIN
BST
SYNC
SW
VOUT
LM5576
SD
IS
RT
VCC
SS
RAMP
OUT
FB
COMP
GND
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
4
4
5
5
5
5
7
Absolute Maximum Ratings ......................................
Handling Ratings: LM5576........................................
Handling Ratings: LM5576-Q1..................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 9
7.1 Overview ................................................................... 9
7.2 Functional Block Diagram ......................................... 9
7.3 Feature Description................................................... 9
7.4 Device Functional Modes........................................ 10
8
Application and Implementation ........................ 16
8.1 Application Information............................................ 16
8.2 Typical Application .................................................. 17
9 Power Supply Recommendations...................... 25
10 Layout................................................................... 25
10.1 Layout Guidelines ................................................. 25
10.2 Layout Example .................................................... 26
11 Device and Documentation Support ................. 28
11.1
11.2
11.3
11.4
Related Links ........................................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
28
28
28
28
12 Mechanical, Packaging, and Orderable
Information ........................................................... 28
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision I (April 2013) to Revision J
•
Page
Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information
section ................................................................................................................................................................................... 1
Changes from Revision H (April 2013) to Revision I
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 26
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
5 Pin Configuration and Functions
20-Pin
HTSSOP Package
Top View
1
VCC
BST
SD
PRE
VIN
SW
VIN
SW
2
3
4
5
6
7
8
9
10
SYNC
IS
COMP
IS
FB
PGND
RT
PGND
RAMP
OUT
AGND
SS
20
19
18
17
16
15
14
13
12
11
Pin Functions
PIN
I/O
DESCRIPTION
APPLICATION INFORMATION
NO.
NAME
1
VCC
O
Output of the bias regulator
VCC tracks VIN up to 9 V. Beyond 9 V, VCC is
regulated to 7 Volts. A 0.1-uF to 1-uF ceramic
decoupling capacitor is required. An external voltage
(7.5 V – 14 V) can be applied to this pin to reduce
internal power dissipation.
2
SD
I
Shutdown or UVLO input
If the SD pin voltage is below 0.7 V the regulator will
be in a low power state. If the SD pin voltage is
between 0.7 V and 1.225 V the regulator will be in
standby mode. If the SD pin voltage is above 1.225 V
the regulator will be operational. An external voltage
divider can be used to set a line undervoltage
shutdown threshold. If the SD pin is left open circuit,
a 5-µA pull-up current source configures the
regulator fully operational.
3, 4
VIN
I
Input supply voltage
Nominal operating range: 6 V to 75 V
5
SYNC
I
Oscillator synchronization input or output
The internal oscillator can be synchronized to an
external clock with an external pull-down device.
Multiple LM5576 devices can be synchronized
together by connection of their SYNC pins.
6
COMP
O
Output of the internal error amplifier
The loop compensation network should be connected
between this pin and the FB pin.
7
FB
I
Feedback signal from the regulated output
This pin is connected to the inverting input of the
internal error amplifier. The regulation threshold is
1.225 V.
8
RT
I
Internal oscillator frequency set input
The internal oscillator is set with a single resistor,
connected between this pin and the AGND pin.
9
RAMP
O
Ramp control signal
An external capacitor connected between this pin
and the AGND pin sets the ramp slope used for
current mode control. Recommended capacitor range
50 pF to 2000 pF.
10
AGND
GROUND
Analog ground
Internal reference for the regulator control functions
11
SS
O
Soft-start
An external capacitor and an internal 10-µA current
source set the time constant for the rise of the error
amp reference. The SS pin is held low during
standby, VCC UVLO and thermal shutdown.
12
OUT
O
Output voltage connection
Connect directly to the regulated output voltage.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
3
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
Pin Functions (continued)
PIN
I/O
DESCRIPTION
APPLICATION INFORMATION
NO.
NAME
13, 14
PGND
GROUND
Power ground
Low side reference for the PRE switch and the IS
sense resistor.
15, 16
IS
I
Current sense
Current measurement connection for the recirculating diode. An internal sense resistor and a
sample/hold circuit sense the diode current near the
conclusion of the off-time. This current measurement
provides the DC level of the emulated current ramp.
17, 18
SW
O
Switching node
The source terminal of the internal buck switch. The
SW pin should be connected to the external Schottky
diode and to the buck inductor.
19
PRE
I
Pre-charge assist for the bootstrap capacitor
This open drain output can be connected to SW pin
to aid charging the bootstrap capacitor during very
light load conditions or in applications where the
output may be pre-charged before the LM5576 is
enabled. An internal pre-charge MOSFET is turned
on for 265 ns each cycle just prior to the on-time
interval of the buck switch.
20
BST
I
Boost input for bootstrap capacitor
An external capacitor is required between the BST
and the SW pins. A 0.022-µF ceramic capacitor is
recommended. The capacitor is charged from VCCvia
an internal diode during the off-time of the buck
switch.
NA
EP
GROUND
Exposed Pad
Exposed metal pad on the underside of the device. It
is recommended to connect this pad to the PWB
ground plane, in order to aid in heat dissipation.
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MAX
UNIT
VIN to GND
MIN
76
V
BST to GND
90
V
PRE to GND
76
V
SW to GND (Steady State)
–1.5
V
BST to VCC
76
V
SD, VCC to GND
14
V
14
V
BST to SW
OUT to GND
Limited to VIN
SYNC, SS, FB, RAMP to GND
(1)
(2)
7
V
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Recommended Operating Conditions are
conditions under which operation of the device is intended to be functional. For ensured specifications and test conditions, see the
Electrical Characteristics.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
6.2 Handling Ratings: LM5576
Tstg
Storage temperature range
V(ESD)
(1)
4
Electrostatic discharge
MIN
MAX
UNIT
–65
150
°C
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins (1)
2
kV
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
6.3 Handling Ratings: LM5576-Q1
Tstg
Storage temperature range
V(ESD)
Electrostatic discharge
(1)
MIN
MAX
–65
150
°C
2
kV
Human body model (HBM), per AEC Q100-002 (1)
UNIT
AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.4 Recommended Operating Conditions
MIN
VIN
MAX
UNIT
6
75
V
Operation Junction Temperature (Q0)
−40
150
°C
Operation Junction Temperature (Q1)
−40
125
°C
6.5 Thermal Information
LM5576
THERMAL METRIC (1)
PWP
UNIT
20 PINS
RθJA
(1)
Junction-to-ambient thermal resistance
40
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
6.6 Electrical Characteristics
Typical values correspond to TJ = 25°C, VIN = 48 V, RT = 32.4kΩ. Minimum and maximum limits apply over –40°C to 125°C
junction temperature range unless otherwise stated. (1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
6.85
7.15
7.45
V
STARTUP REGULATOR
VCC Reg
VCC Regulator Output
VCC LDO Mode turn-off
VCC Current Limit
VCC = 0 V
VCC UVLO Threshold
(VCC increasing)
9
V
25
mA
VCC SUPPLY
5.03
VCC Undervoltage Hysteresis
5.35
5.67
V
0.25
V
Bias Current (Iin)
FB = 1.3 V
3.4
4.5
mA
Shutdown Current (Iin)
SD = 0 V
57
85
µA
0.7
0.9
V
SHUTDOWN THRESHOLDS
Shutdown Threshold
(SD Increasing)
0.47
Shutdown Hysteresis
0.1
Standby Threshold
(Standby Increasing)
1.17
Standby Hysteresis
SD Pull-up Current Source
1.225
V
1.28
V
0.1
V
5
µA
SWITCH CHARACTERISTICS
Buck Switch Rds(on) (Q0)
170
380
mΩ
Buck Switch Rds(on) (Q1)
170
340
mΩ
BOOST UVLO
3.8
BOOST UVLO Hysteresis
V
0.56
V
Pre-charge Switch Rds(on)
70
Ω
Pre-charge Switch on-time
265
ns
CURRENT LIMIT
Cycle by Cycle Current Limit (Q0)
(1)
RAMP = 0 V
3.6
4.2
5.5
A
Min and Max limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation
using Statistical Quality Control (SQC) methods. Limits are used to calculate Texas Instruments' Average Outgoing Quality Level
(AOQL).
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
5
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
Electrical Characteristics (continued)
Typical values correspond to TJ = 25°C, VIN = 48 V, RT = 32.4kΩ. Minimum and maximum limits apply over –40°C to 125°C
junction temperature range unless otherwise stated.(1)
PARAMETER
TEST CONDITIONS
Cycle by Cycle Current Limit (Q1)
RAMP = 0 V
Cycle by Cycle Current Limit Delay
RAMP = 2.5 V
MIN
TYP
MAX
3.6
4.2
5.1
100
UNIT
A
ns
SOFT-START
SS Current Source
7
10
14
µA
180
200
220
kHz
425
485
545
kHz
OSCILLATOR
Frequency1
Frequency2
RT = 11kΩ
SYNC Source Impedance
11
kΩ
SYNC Sink Impedance
110
Ω
SYNC Threshold (falling)
1.3
SYNC Frequency
RT = 11kΩ
SYNC Pulse Width Minimum
V
550
kHz
15
ns
RAMP GENERATOR
Ramp Current 1
VIN = 60 V, VOUT=10 V
235
275
315
µA
Ramp Current 2
VIN = 10 V, VOUT=10 V
18
25
32
µA
Forced Off-time (Q0)
390
500
590
ns
Forced Off-time (Q1)
416
500
575
ns
PWM COMPARATOR
Min On-time
80
ns
COMP to PWM Comparator Offset
0.7
V
ERROR AMPLIFIER
Feedback Voltage (Q0)
Vfb = COMP
1.207
1.225
1.243
Feedback Voltage (Q1)
Vfb = COMP
1.207
1.225
1.243
FB Bias Current
17
DC Gain
70
COMP Sink / Source Current
3
Unity Gain Bandwidth
V
V
nA
dB
mA
3
MHz
42
mΩ
DIODE SENSE RESISTANCE
DSENSE
THERMAL SHUTDOWN
Tsd
Thermal Shutdown Threshold (Q0)
180
°C
Tsd
Thermal Shutdown Threshold (Q1)
165
°C
25
°C
Thermal Shutdown Hysteresis
6
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
6.7 Typical Characteristics
OSCILLATOR FREQUENCY (kHz)
1000
100
10
1
10
100
1000
RT (k:)
NORMALIZED OSCILLATOR FREQUENCY
Figure 1. Oscillator Frequency vs RT
Figure 2. Oscillator Frequency vs Temperature (Q0) FOSC =
200kHz
1.010
1.005
1.000
0.995
0.990
-50
-25
0
25
50
75
100
125
TEMPERATURE (oC)
Figure 4. Soft Start Current vs Temperature (Q0)
1.10
8
1.05
6
VCC (V)
NORMALIZED SOFTSTART CURRENT
Figure 3. Oscillator Frequency vs Temperature (Q1) FOSC =
200kHz
1.00
0.95
0.90
-50
4
2
-25
0
25
50
75
100
125
0
0
TEMPERATURE (oC)
4
8
12
16
20
24
ICC (mA)
Figure 5. Soft Start Current vs Temperature (Q1)
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Figure 6. VCC vs ICC VIN = 12 V
Submit Documentation Feedback
7
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
Typical Characteristics (continued)
10
50
225
40
180
30
135
4
Ramp Down
PHASE
10
45
0
0
GAIN
-10
2
90
PHASE (°)
6
20
GAIN (dB)
VCC (V)
8
-45
Ramp Up
-20
0
0
2
4
6
8
-90
-30
10k
10
100k
VIN (V)
1M
10M
-135
100M
FREQUENCY (Hz)
Figure 7. VCC vs VIN RL = 7kω
Figure 8. Error Amplifier Gain/Phase AVCL = 101
100
90
EFFICIENCY (%)
80
70
60
50
VIN = 24V
VIN = 7V
VIN = 48V
40
30
VIN = 75V
20
10
0
0.5
1
1.5
2
2.5
3
IOUT (A)
Figure 9. Demoboard Efficiency vs IOUT and VIN
8
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
7 Detailed Description
7.1 Overview
The LM5576 switching regulator features all of the functions necessary to implement an efficient high voltage
buck regulator using a minimum of external components. This easy to use regulator integrates a 75 V N-Channel
buck switch with an output current capability of 3 Amps. The regulator control method is based on current mode
control utilizing an emulated current ramp. Peak current mode control provides inherent line voltage feed-forward,
cycle-by-cycle current limiting, and ease of loop compensation. The use of an emulated control ramp reduces
noise sensitivity of the pulse-width modulation circuit, allowing reliable processing of very small duty cycles
necessary in high input voltage applications. The operating frequency is user programmable from 50 kHz to 500
kHz. An oscillator synchronization pin allows multiple LM5576 regulators to self synchronize or be synchronized
to an external clock. The output voltage can be set as low as 1.225 V. Fault protection features include, current
limiting, thermal shutdown and remote shutdown capability. The device is available in the HTSSOP-20 package
featuring an exposed pad to aid thermal dissipation.
The functional block diagram and typical application of the LM5576 are shown in the Functional Block Diagram
section. The LM5576 can be applied in numerous applications to efficiently step-down a high, unregulated input
voltage. The device is well suited for telecom, industrial and automotive power bus voltage ranges.
7.2 Functional Block Diagram
VIN
7V ± 75V
C1
2.2
3, 4 VIN
C2
2.2
5 PA
R1
OPEN
LM5576
7V
REGULATOR
1.225V
2 SD
STANDBY
VCC
SHUTDOWN
0.7V
SD
C12
OPEN
R2
OPEN
11 SS
BST
UVLO
C7
0.022
DRIVER
S Q
1.225V
20
VIN
DIS
CLK
10 PA
C4
0.01
C8
0.47
THERMAL
SHUTDOWN
UVLO
1
R Q
LEVEL
SHIFT
PWM
0.7V
PRE 19
C_LIMIT
7 FB
C6
open
C5
0.01
R4
49.9k
ERROR
AMP
0.5V/A
+
6 COMP
CLK
Ir
OSCILLATOR
SYNC
5
RT
8
RAMP
9
SYNC
D1
CSHD6-100C
CLK
2.1V
VIN
L1
33 PH
SW 17, 18
TRACK
SAMPLE
and
HOLD
RAMP GENERATOR
Ir = (5 PA x (VIN ± VOUT))
+ 25 PA
IS
C11
330p
R7
10
C10
150
5V
C9
22
15, 16
PGND 13, 14
AGND 10
CLK
OUT
12
R5
5.11k
R6
1.65k
C3
330p
R3
21k
7.3 Feature Description
7.3.1 Shutdown / Standby
The LM5576 contains a dual level Shutdown (SD) circuit. When the SD pin voltage is below 0.7 V, the regulator
is in a low current shutdown mode. When the SD pin voltage is greater than 0.7 V but less than 1.225 V, the
regulator is in standby mode. In standby mode the VCC regulator is active but the output switch is disabled. When
the SD pin voltage exceeds 1.225 V, the output switch is enabled and normal operation begins. An internal 5 µA
pull-up current source configures the regulator to be fully operational if the SD pin is left open.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
9
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
Feature Description (continued)
An external set-point voltage divider from VIN to GND can be used to set the operational input range of the
regulator. The divider must be designed such that the voltage at the SD pin will be greater than 1.225 V when
VIN is in the desired operating range. The internal 5 µA pull-up current source must be included in calculations of
the external set-point divider. Hysteresis of 0.1 V is included for both the shutdown and standby thresholds. The
SD pin is internally clamped with a 1 kΩ resistor and an 8 V zener clamp. The voltage at the SD pin should never
exceed 14 V. If the voltage at the SD pin exceeds 8 V, the bias current will increase at a rate of 1 mA/V.
The SD pin can also be used to implement various remote enable / disable functions. Pulling the SD pin below
the 0.7 V threshold totally disables the controller. If the SD pin voltage is above 1.225 V the regulator will be
operational.
7.3.2 Soft-Start
The soft-start feature allows the regulator to gradually reach the initial steady state operating point, thus reducing
start-up stresses and surges. The internal soft-start current source, set to 10 µA, gradually increases the voltage
of an external soft-start capacitor connected to the SS pin. The soft-start capacitor voltage is connected to the
reference input of the error amplifier. Various sequencing and tracking schemes can be implemented using
external circuits that limit or clamp the voltage level of the SS pin.
In the event a fault is detected (over-temperature, VCC UVLO, SD) the soft-start capacitor will be discharged.
When the fault condition is no longer present a new soft-start sequence will commence.
7.3.3 Thermal Protection
Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction
temperature is exceeded. When activated, typically at 165°C (Q1 version) and 180°C (Q0 version), the controller
is forced into a low power reset state, disabling the output driver and the bias regulator. This feature is provided
to prevent catastrophic failures from accidental device overheating.
7.4 Device Functional Modes
7.4.1 High Voltage Start-Up Regulator
The LM5576 contains a dual-mode internal high voltage startup regulator that provides the CC bias supply for the
PWM controller and boot-strap MOSFET gate driver. The input pin (VIN) can be connected directly to the input
voltage, as high as 75 Volts. For input voltages below 9 V, a low dropout switch connects VCC directly to VIN. In
this supply range, VCC is approximately equal to VIN. For VIN voltage greater than 9 V, the low dropout switch is
disabled and the VCC regulator is enabled to maintain VCC at approximately 7 V. The wide operating range of 6 V
to 75 V is achieved through the use of this dual mode regulator.
The output of the VCC regulator is current limited to 25 mA. Upon power up, the regulator sources current into the
capacitor connected to the VCC pin. When the voltage at the VCC pin exceeds the VCC UVLO threshold of 5.35
V and the SD pin is greater than 1.225 V, the output switch is enabled and a soft-start sequence begins. The
output switch remains enabled until VCC falls below 5.0 V or the SD pin falls below 1.125 V.
An auxiliary supply voltage can be applied to the VCC pin to reduce the IC power dissipation. If the auxiliary
voltage is greater than 7.3 V, the internal regulator will essentially shut off, reducing the IC power dissipation.
The VCC regulator series pass transistor includes a diode between VCC and VIN that should not be forward biased
in normal operation. Therefore the auxiliary VCC voltage should never exceed the VIN voltage.
In high voltage applications extra care should be taken to ensure the VIN pin does not exceed the absolute
maximum voltage rating of 76 V. During line or load transients, voltage ringing on the VIN line that exceeds the
Absolute Maximum Ratings can damage the IC. Both careful PC board layout and the use of quality bypass
capacitors located close to the VIN and GND pins are essential.
10
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
Device Functional Modes (continued)
VIN
9V
VCC
7V
5.25V
Internal Enable Signal
Figure 10. VIN and VCC Sequencing
7.4.2 Oscillator and Sync Capability
The LM5576 oscillator frequency is set by a single external resistor connected between the RT pin and the
AGND pin. The RT resistor should be located very close to the device and connected directly to the pins of the IC
(RT and AGND).To set a desired oscillator frequency (F), the necessary value for the RT resistor can be
calculated from the following equation:
1 - 580 x 10-9
F
RT =
135 x 10-12
(1)
The SYNC pin can be used to synchronize the internal oscillator to an external clock. The external clock must be
of higher frequency than the free-running frequency set by the RT resistor. A clock circuit with an open drain
output is the recommended interface from the external clock to the SYNC pin. The clock pulse duration should
be greater than 15 ns.
LM5576
SYNC
SW
SYNC
AGND
CLK
SW
500 ns
Figure 11. Sync From External Clock
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
11
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
Device Functional Modes (continued)
LM5576
SYNC
LM5576
SYNC
UP TO 5 TOTAL
DEVICES
Figure 12. Sync From Multiple Devices
Multiple LM5576 devices can be synchronized together simply by connecting the SYNC pins together. In this
configuration all of the devices will be synchronized to the highest frequency device. The diagram in Figure 13
illustrates the SYNC input/output features of the LM5576. The internal oscillator circuit drives the SYNC pin with
a strong pull-down / weak pull-up inverter. When the SYNC pin is pulled low either by the internal oscillator or an
external clock, the ramp cycle of the oscillator is terminated and a new oscillator cycle begins. Thus, if the SYNC
pins of several LM5576 ICs are connected together, the IC with the highest internal clock frequency will pull the
connected SYNC pins low first and terminate the oscillator ramp cycles of the other ICs. The LM5576 with the
highest programmed clock frequency will serve as the master and control the switching frequency of the all the
devices with lower oscillator frequency.
5V
SYNC
10k
I = f(RT)
2.5V
Q
S
Q
R
DEADTIME
ONE-SHOT
Figure 13. Simplified Oscillator Block Diagram and Sync I/O Circuit
7.4.3 Error Amplifier and PWM Comparator
The internal high gain error amplifier generates an error signal proportional to the difference between the
regulated output voltage and an internal precision reference (1.225 V). The output of the error amplifier is
connected to the COMP pin allowing the user to provide loop compensation components, generally a type II
network, as illustrated in the Functional Block Diagram section. This network creates a pole at DC, a zero and a
noise reducing high frequency pole. The PWM comparator compares the emulated current sense signal from the
RAMP generator to the error amplifier output voltage at the COMP pin.
12
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
Device Functional Modes (continued)
7.4.4 Ramp Generator
The ramp signal used in the pulse width modulator for current mode control is typically derived directly from the
buck switch current. This switch current corresponds to the positive slope portion of the output inductor current.
Using this signal for the PWM ramp simplifies the control loop transfer function to a single pole response and
provides inherent input voltage feed-forward compensation. The disadvantage of using the buck switch current
signal for PWM control is the large leading edge spike due to circuit parasitics that must be filtered or blanked.
Also, the current measurement may introduce significant propagation delays. The filtering, blanking time and
propagation delay limit the minimum achievable pulsewidth. In applications where the input voltage may be
relatively large in comparison to the output voltage, controlling small pulsewidths and duty cycles is necessary for
regulation. The LM5576 utilizes a unique ramp generator, which does not actually measure the buck switch
current but rather reconstructs the signal. Reconstructing or emulating the inductor current provides a ramp
signal to the PWM comparator that is free of leading edge spikes and measurement or filtering delays. The
current reconstruction is comprised of two elements; a sample & hold DC level and an emulated current ramp.
RAMP
t
(5m ´ (VIN - VOUT ) - 25m )´ C ON
RAMP
tON
Sample and Hold DC Level
0.5V/A
Figure 14. Composition of Current Sense Signal
The sample & hold DC level illustrated in Figure 14 is derived from a measurement of the re-circulating Schottky
diode anode current. The re-circulating diode anode should be connected to the IS pin. The diode current flows
through an internal current sense resistor between the IS and PGND pins. The voltage level across the sense
resistor is sampled and held just prior to the onset of the next conduction interval of the buck switch. The diode
current sensing and sample & hold provide the DC level of the reconstructed current signal. The positive slope
inductor current ramp is emulated by an external capacitor connected from the RAMP pin to AGND and an
internal voltage controlled current source. The ramp current source that emulates the inductor current is a
function of the VIN and VOUT voltages per Equation 2:
IRAMP = (5 µ x (VIN – VOUT)) + 25 µA
(2)
Proper selection of the RAMP capacitor depends upon the selected value of the output inductor. The value of
CRAMP can be selected from:
CRAMP = L x 10-5
where
•
L is the value of the output inductor in Henrys
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
(3)
Submit Documentation Feedback
13
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
Device Functional Modes (continued)
With this value, the scale factor of the emulated current ramp will be approximately equal to the scale factor of
the DC level sample and hold ( 0.5 V / A). The CRAMP capacitor should be located very close to the device and
connected directly to the pins of the IC (RAMP and AGND).
For duty cycles greater than 50%, peak current mode control circuits are subject to sub-harmonic oscillation.
Sub-harmonic oscillation is normally characterized by observing alternating wide and narrow pulses at the switch
node. Adding a fixed slope voltage ramp (slope compensation) to the current sense signal prevents this
oscillation. The 25 µA of offset current provided from the emulated current source adds some fixed slope to the
ramp signal. In some high output voltage, high duty cycle applications, additional slope may be required. In these
applications, a pull-up resistor may be added between the VCC and RAMP pins to increase the ramp slope
compensation.
For VOUT > 7.5 V:
Calculate optimal slope current, IOS = VOUT x 5 µA/V.
For example, at VOUT = 10 V, IOS = 50 µA.
Install a resistor from the RAMP pin to VCC:
RRAMP = VCC / (IOS - 25 µA)
(4)
VCC
RRAMP
RAMP
CRAMP
Figure 15. RRAMP to VCC for VOUT > 7.5 V
Note that the emulated ramp signal on CRAMP is applied to the current limit comparator as described in the
Current Limit section below. Increasing the ramp slope will result in lower current limit threshold. This can lower
the output current capability of the part to less than 3 A in some conditions. The resulting current limit threshold
can be calculated by the following equation:
where
•
•
•
•
•
•
•
•
•
•
VCL = 2.1 V
gm = 5 µA/V
Ioffset = 25 µA
A x Rs = 0.5 V/A
VCC = 7 V
T = switching period
D = duty cycle (approximately VOUT / VIN)
L = inductor value
CRAMP = ramp capacitor value
RRAMP = ramp resistor value
(5)
If the recommended CRAMP and RRAMP values are used, then the following simplified equation calculates the
current limit threshold:
14
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
Device Functional Modes (continued)
(6)
7.4.5 Maximum Duty Cycle / Input Drop-Out Voltage
There is a forced off-time of 500 ns implemented each cycle to ensure sufficient time for the diode current to be
sampled. This forced off-time limits the maximum duty cycle of the buck switch. The maximum duty cycle will
vary with the operating frequency.
DMAX = 1 - Fs x 500ns
where
•
Fs is the oscillator frequency
(7)
Limiting the maximum duty cycle will raise the input dropout voltage. The input dropout voltage is the lowest input
voltage required to maintain regulation of the output voltage. An approximation of the input dropout voltage is:
Vout + VD
VinMIN =
1 - Fs x 500 ns
where
•
VD is the voltage drop across the re-circulatory diode
(8)
Operating at high switching frequency raises the minimum input voltage necessary to maintain regulation.
7.4.6 Boost Pin
The LM5576 integrates an N-Channel buck switch and associated floating high voltage level shift / gate driver.
This gate driver circuit works in conjunction with an internal diode and an external bootstrap capacitor. A 0.022
µF ceramic capacitor, connected with short traces between the BST pin and SW pin, is recommended. During
the off-time of the buck switch, the SW pin voltage is approximately -0.5 V and the bootstrap capacitor is charged
from VCC through the internal bootstrap diode. When operating with a high PWM duty cycle, the buck switch will
be forced off each cycle for 500 ns to ensure that the bootstrap capacitor is recharged.
Under very light load conditions or when the output voltage is pre-charged, the SW voltage will not remain low
during the off-time of the buck switch. If the inductor current falls to zero and the SW pin rises, the bootstrap
capacitor will not receive sufficient voltage to operate the buck switch gate driver. For these applications, the
PRE pin can be connected to the SW pin to pre-charge the bootstrap capacitor. The internal pre-charge
MOSFET and diode connected between the PRE pin and PGND turns on each cycle for 265 ns just prior to the
onset of a new switching cycle. If the SW pin is at a normal negative voltage level (continuous conduction mode),
then no current will flow through the pre-charge MOSFET/diode. For output voltages above 5 V, a minimum load
current may still be required to ensure that the SW voltage is pulled low enough to recharge the bootstrap
capacitor.
7.4.7 Current Limit
The LM5576 contains a unique current monitoring scheme for control and over-current protection. When set
correctly, the emulated current sense signal provides a signal which is proportional to the buck switch current
with a scale factor of 0.5 V / A. The emulated ramp signal is applied to the current limit comparator. If the
emulated ramp signal exceeds 2.1 V (4.2 A) the present current cycle is terminated (cycle-by-cycle current
limiting). In applications with small output inductance and high input voltage the switch current may overshoot
due to the propagation delay of the current limit comparator. If an overshoot should occur, the diode current
sampling circuit will detect the excess inductor current during the off-time of the buck switch. If the sample & hold
DC level exceeds the 2.1 V current limit threshold, the buck switch will be disabled and skip pulses until the
diode current sampling circuit detects the inductor current has decayed below the current limit threshold. This
approach prevents current runaway conditions due to propagation delays or inductor saturation since the inductor
current is forced to decay following any current overshoot.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
15
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 Bias Power Dissipation Reduction
Buck regulators operating with high input voltage can dissipate an appreciable amount of power for the bias of
the IC. The VCC regulator must step-down the input voltage VIN to a nominal VCC level of 7 V. The large voltage
drop across the VCC regulator translates into a large power dissipation within the regulator. There are several
techniques that can significantly reduce this bias regulator power dissipation. Figure 16 and VCC Figure 17 depict
two methods to bias the IC from the output voltage. In each case the internal VCC regulator is used to initially bias
the VCC pin. After the output voltage is established, the VCC pin potential is raised above the nominal 7 V
regulation level, which effectively disables the internal VCC regulator. The voltage applied to the VCC pin should
never exceed 14 V. The VCC voltage should never be larger than the VIN voltage.
LM5576
BST
VOUT
SW
L1
COUT
D1
IS
GND
VCC
D2
Figure 16. VCC Bias From VOUT for 8 V < VOUT < 14 V
16
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
Application Information (continued)
LM5576
BST
VOUT
L1
SW
D1
COUT
IS
GND
D2
VCC
Figure 17. VCC Bias With Additional Winding on the Output Inductor
8.2 Typical Application
VIN
7V ± 75V
C1
2.2
3, 4 VIN
C2
2.2
5 PA
R1
OPEN
LM5576
7V
REGULATOR
1.225V
2 SD
STANDBY
VCC
SHUTDOWN
0.7V
SD
C12
OPEN
R2
OPEN
11 SS
C8
0.47
THERMAL
SHUTDOWN
UVLO
BST
UVLO
C4
0.01
C7
0.022
DRIVER
S Q
1.225V
20
VIN
DIS
CLK
10 PA
1
R Q
LEVEL
SHIFT
PWM
0.7V
PRE 19
C_LIMIT
7 FB
C6
open
C5
0.01
R4
49.9k
ERROR
AMP
0.5V/A
+
6 COMP
CLK
Ir
OSCILLATOR
SYNC
5
RT
8
RAMP
9
SYNC
D1
CSHD6-100C
CLK
2.1V
VIN
L1
33 PH
SW 17, 18
TRACK
SAMPLE
and
HOLD
RAMP GENERATOR
Ir = (5 PA x (VIN ± VOUT))
+ 25 PA
IS
C11
330p
R7
10
C10
150
5V
C9
22
15, 16
PGND 13, 14
AGND 10
CLK
OUT
12
R5
5.11k
R6
1.65k
C3
330p
R3
21k
Figure 18. Typical Application
8.2.1 Design Requirements
The circuit shown in Figure 18 is configured for the following specifications:
• VOUT = 5 V
• VIN = 7 V to 75 V
• Fs = 300 kHz
• Minimum load current (for CCM) = 250 mA
• Maximum load current = 3 A
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
17
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
Typical Application (continued)
8.2.2 Detailed Design Procedure
8.2.2.1 External Components
The procedure for calculating the external components is illustrated with the following design example. The Bill of
Materials for this design is listed in Table 1.
Table 1. 5 V, 3 A Demo Board Bill of Materials
ITEM
PART NUMBER
DESCRIPTION
VALUE
C
1
C4532X7R2A225M
CAPACITOR, CER, TDK
2.2 µ, 100 V
C
2
C4532X7R2A225M
CAPACITOR, CER, TDK
2.2 µ, 100 V
C
3
C0805C331G1GAC
CAPACITOR, CER, KEMET
330 p, 100 V
C
4
C2012X7R2A103K
CAPACITOR, CER, TDK
0.01 µ, 100 V
C
5
C2012X7R2A103K
CAPACITOR, CER, TDK
0.01 µ, 100 V
C
6
OPEN
NOT USED
C
7
C2012X7R2A223K
CAPACITOR, CER, TDK
0.022 µ, 100 V
C
8
C2012X7R1C474M
CAPACITOR, CER, TDK
0.47 µ, 16 V
C
9
C3225X7R1C226M
CAPACITOR, CER, TDK
22 µ, 16 V
C
10
EEFHE0J151R
CAPACITOR, SP, PANASONIC
150 µ, 6.3 V
C
11
C0805C331G1GAC
CAPACITOR, CER, KEMET
330 p, 100 V
C
12
OPEN
NOT USED
D
1
CSHD6-100C
DIODE, 100V, CENTRAL
6CWQ10FN
DIODE, 100V, IR (D1-ALT)
L
1
DR127-330
INDUCTOR, COOPER
R
1
OPEN
NOT USED
R
2
OPEN
NOT USED
R
3
CRCW08052102F
RESISTOR
21 kΩ
R
4
CRCW08054992F
RESISTOR
49.9 kΩ
R
5
CRCW08055111F
RESISTOR
5.11 kΩ
R
6
CRCW08051651F
RESISTOR
1.65 kΩ
R
7
CRCW2512100J
RESISTOR
10, 1 W
U
1
LM5576
REGULATOR, TEXAS INSTRUMENTS
33 µH
8.2.2.2 R3 (RT)
RT sets the oscillator switching frequency. Generally, higher frequency applications are smaller but have higher
losses. Operation at 300 kHz was selected for this example as a reasonable compromise for both small size and
high efficiency. The value of RT for 300 kHz switching frequency can be calculated as follows:
RT =
ææ
1
çç
3
è è 300 ´ 10
ö
-9 ö
÷ - 580 ´ 10 ÷
ø
ø
135 ´ 10-12
(9)
The nearest standard value of 21 kΩ was chosen for RT.
8.2.2.3 L1
The inductor value is determined based on the operating frequency, load current, ripple current, and the
minimum and maximum input voltage (VIN(min), VIN(max)).
18
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
L1 Current
IPK+
IRIPPLE
IO
IPK-
1/Fs
0 mA
Figure 19. Inductor Current Waveform
To keep the circuit in continuous conduction mode (CCM), the maximum ripple current IRIPPLE should be less
than twice the minimum load current, or 0.5 Ap-p. Using this value of ripple current, the value of inductor (L1) is
calculated using the following:
L1 =
(
VOUT ´ VIN(max ) - VOUT
L1 =
)
IRIPPLE ´ FS ´ VIN(max )
(10)
5V x (75V ± 5V)
= 31 PH
0.5A x 300 kHz x 75V
(11)
This procedure provides a guide to select the value of L1. The nearest standard value (33 µH) will be used. L1
must be rated for the peak current (IPK+) to prevent saturation. During normal loading conditions, the peak current
occurs at maximum load current plus maximum ripple. During an overload condition the peak current is limited to
4.2 A nominal (5.1 A maximum). The selected inductor (see Table 1) has a conservative 6.2 Amp saturation
current rating. For this manufacturer, the saturation rating is defined as the current necessary for the inductance
to reduce by 30%, at 20°C.
8.2.2.4 C3 (CRAMP)
With the inductor value selected, the value of C3 (CRAMP) necessary for the emulation ramp circuit is:
CRAMP = L x 10-5
(12)
Where:
L is in Henrys
With L1 selected for 33 µH the recommended value for C3 is 330 pF.
8.2.2.5 C9, C10
The output capacitors, C9 and C10, smooth the inductor ripple current and provide a source of charge for
transient loading conditions. For this design a 22-µF ceramic capacitor and a 150-µF SP organic capacitor were
selected. The ceramic capacitor provides ultra low ESR to reduce the output ripple voltage and noise spikes,
while the SP capacitor provides a large bulk capacitance in a small volume for transient loading conditions. An
approximation for the output ripple voltage is:
§
¨
©
§
1
'VOUT = 'IL x ¨ESR +
8
x
F
S x COUT
©
(13)
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
19
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
8.2.2.6 D1
A Schottky type re-circulating diode is required for all LM5576 applications. Ultra-fast diodes are not
recommended and may result in damage to the IC due to reverse recovery current transients. The near ideal
reverse recovery characteristics and low forward voltage drop are particularly important diode characteristics for
high input voltage and low output voltage applications common to the LM5576. The reverse recovery
characteristic determines how long the current surge lasts each cycle when the buck switch is turned on. The
reverse recovery characteristics of Schottky diodes minimize the peak instantaneous power in the buck switch
occurring during turn-on each cycle. The resulting switching losses of the buck switch are significantly reduced
when using a Schottky diode. The reverse breakdown rating should be selected for the maximum VIN, plus some
safety margin.
The forward voltage drop has a significant impact on the conversion efficiency, especially for applications with a
low output voltage. “Rated” current for diodes vary widely from various manufacturers. The worst case is to
assume a short circuit load condition. In this case the diode will carry the output current almost continuously. For
the LM5576 this current can be as high as 4.2 A. Assuming a worst case 1 V drop across the diode, the
maximum diode power dissipation can be as high as 4.2 W. For the reference design a 100 V Schottky in a
DPAK package was selected.
8.2.2.7 C1, C2
The regulator supply voltage has a large source impedance at the switching frequency. Good quality input
capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the switch current
during the on-time. When the buck switch turns on, the current into the VIN pin steps to the lower peak of the
inductor current waveform, ramps up to the peak value, then drops to zero at turn-off. The average current into
VIN during the on-time is the load current. The input capacitance should be selected for RMS current rating and
minimum ripple voltage. A good approximation for the required ripple current rating necessary is IRMS > IOUT / 2.
Quality ceramic capacitors with a low ESR should be selected for the input filter. To allow for capacitor
tolerances and voltage effects, two 2.2-µF, 100 V ceramic capacitors will be used. If step input voltage transients
are expected near the maximum rating of the LM5576, a careful evaluation of ringing and possible spikes at the
device VIN pin should be completed. An additional damping network or input voltage clamp may be required in
these cases.
8.2.2.8 C8
The capacitor at the VCC pin provides noise filtering and stability for the VCC regulator. The recommended value
of C8 should be no smaller than 0.1-µF, and should be a good quality, low ESR, ceramic capacitor. A value of
0.47-µF was selected for this design.
8.2.2.9 C7
The bootstrap capacitor between the BST and the SW pins supplies the gate current to charge the buck switch
gate at turn-on. The recommended value of C7 is 0.022-µF, and should be a good quality, low ESR, ceramic
capacitor.
8.2.2.10 C4
The capacitor at the SS pin determines the soft-start time, i.e. the time for the reference voltage and the output
voltage, to reach the final regulated value. The time is determined from:
C4 ´ 1.225 V
tSS =
10 mA
(14)
For this application, a C4 value of 0.01-µF was chosen which corresponds to a soft-start time of 1 ms.
8.2.2.11 R5, R6
R5 and R6 set the output voltage level, the ratio of these resistors is calculated from:
R5/R6 = (VOUT / 1.225 V) - 1
20
Submit Documentation Feedback
(15)
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
For a 5 V output, the R5/R6 ratio calculates to 3.082. The resistors should be chosen from standard value
resistors, a good starting point is selection in the range of 1.0 kΩ - 10 kΩ. Values of 5.11 kΩ for R5, and 1.65 kΩ
for R6 were selected.
8.2.2.12 R1, R2, C12
A voltage divider can be connected to the SD pin to set a minimum operating voltage VIN(min) for the regulator. If
this feature is required, the easiest approach to select the divider resistor values is to select a value for R1
(between 10 kΩ and 100 kΩ recommended) then calculate R2 from:
§
¨
©
§
R1
R2 = 1.225 x ¨
-6
© VIN(min) + (5 x 10 x R1) ± 1.225
(16)
Capacitor C12 provides filtering for the divider. The voltage at the SD pin should never exceed 8 V, when using
an external set-point divider it may be necessary to clamp the SD pin at high input voltage conditions. The
reference design utilizes the full range of the LM5576 (6V to 75V); therefore these components can be omitted.
With the SD pin open circuit the LM5576 responds once the VCC UVLO threshold is satisfied.
8.2.2.13 R7, C11
A snubber network across the power diode reduces ringing and spikes at the switching node. Excessive ringing
and spikes can cause erratic operation and couple spikes and noise to the output. Voltage spikes beyond the
rating of the LM5576 or the re-circulating diode can damage these devices. Selecting the values for the snubber
is best accomplished through empirical methods. First, make sure the lead lengths for the snubber connections
are very short. For the current levels typical for the LM5576 a resistor value between 5 and 20 Ohms is
adequate. Increasing the value of the snubber capacitor results in more damping but higher losses. Select a
minimum value of C11 that provides adequate damping of the SW pin waveform at high load.
8.2.2.14 R4, C5, C6
These components configure the error amplifier gain characteristics to accomplish a stable overall loop gain. One
advantage of current mode control is the ability to close the loop with only two feedback components, R4 and C5.
The overall loop gain is the product of the modulator gain and the error amplifier gain. The DC modulator gain of
the LM5576 is as follows:
DC Gain(MOD) = Gm(MOD) x RLOAD = 2 x RLOAD
(17)
The dominant low frequency pole of the modulator is determined by the load resistance (RLOAD,) and output
capacitance (COUT). The corner frequency of this pole is:
fp(MOD) = 1 / (2π RLOAD COUT)
(18)
For RLOAD = 5 Ω and COUT = 177 µF then fp(MOD) = 180 Hz
DC Gain(MOD) = 2 x 5 = 10 = 20 dB
For the design example of Figure 18 the following modulator gain vs. frequency characteristic was measured as
shown in Figure 20.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
21
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
REF LEVEL
0.000 dB
0.0 deg
/DIV
10.000 dB
45.000 deg
GAIN
0
PHASE
100
1k
START 50.000 Hz
10k
STOP 50 000.000 Hz
Figure 20. Gain and Phase of Modulator R = 5 Ohms and
C = 177 µF Loadout
Components R4 and C5 configure the error amplifier as a type II configuration which has a pole at DC and a
zero at fZ = 1 / (2πR4C5). The error amplifier zero cancels the modulator pole leaving a single pole response at
the crossover frequency of the loop gain. A single pole response at the crossover frequency yields a very stable
loop with 90 degrees of phase margin.
For the design example, a target loop bandwidth (crossover frequency) of 20 kHz was selected. The
compensation network zero (fZ) should be selected at least an order of magnitude less than the target crossover
frequency. This constrains the product of R4 and C5 for a desired compensation network zero 1 / (2π R4 C5) to
be less than 2 kHz. Increasing R4, while proportionally decreasing C5, increases the error amp gain. Conversely,
decreasing R4 while proportionally increasing C5, decreases the error amp gain. For the design example C5 was
selected for 0.01-µF and R4 was selected for 49.9 kΩ. These values configure the compensation network zero at
320 Hz. The error amp gain at frequencies greater than fZ is: R4 / R5, which is approximately 10 (20 dB).
REF LEVEL
0.000 dB
0.0 deg
/DIV
10.000 dB
45.000 deg
PHASE
GAIN
0
100
1k
START 50.000 Hz
10k
STOP 50 000.000 Hz
Figure 21. Error Amplifier Gain and Phase
The overall loop can be predicted as the sum (in dB) of the modulator gain and the error amp gain.
22
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
REF LEVEL
0.000 dB
0.0 deg
/DIV
10.000 dB
45.000 deg
GAIN
PHASE
0
100
1k
START 50.000 Hz
10k
STOP 50 000.000 Hz
Figure 22. Overall Loop Gain and Phase
If a network analyzer is available, the modulator gain can be measured and the error amplifier gain can be
configured for the desired loop transfer function. If a network analyzer is not available, the error amplifier
compensation components can be designed with the guidelines given. Step load transient tests can be
performed to verify acceptable performance. The step load goal is minimum overshoot with a damped response.
C6 can be added to the compensation network to decrease noise susceptibility of the error amplifier. The value
of C6 must be sufficiently small since the addition of this capacitor adds a pole in the error amplifier transfer
function. This pole must be well beyond the loop crossover frequency. A good approximation of the location of
the pole added by C6 is: fp2 = fz x C5 / C6.
8.2.3 Application Curves
100
90
80
EFFICIENCY (%)
OSCILLATOR FREQUENCY (kHz)
1000
100
70
60
50
VIN = 24V
VIN = 7V
VIN = 48V
40
30
VIN = 75V
20
10
10
1
10
100
1000
0
0.5
RT (k:)
1
1.5
2
2.5
3
IOUT (A)
Figure 23. Oscillator Frequency vs RT
Figure 24. Demoboard Efficiency vs IOUT and VIN
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
23
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
REF LEVEL
0.000 dB
0.0 deg
www.ti.com
/DIV
10.000 dB
45.000 deg
REF LEVEL
0.000 dB
0.0 deg
/DIV
10.000 dB
45.000 deg
PHASE
GAIN
GAIN
0
0
PHASE
100
1k
START 50.000 Hz
10k
100
1k
START 50.000 Hz
STOP 50 000.000 Hz
Figure 25. Gain and Phase Of Modulator R = 5 Ohms And
C = 177 µF Loadout
REF LEVEL
0.000 dB
0.0 deg
10k
STOP 50 000.000 Hz
Figure 26. Error Amplifier Gain and Phase
/DIV
10.000 dB
45.000 deg
GAIN
PHASE
0
100
1k
START 50.000 Hz
10k
STOP 50 000.000 Hz
Figure 27. Overall Loop Gain and Phase
24
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
9 Power Supply Recommendations
The LM5576 is designed to operate from an input voltage supply range between 6 V and 75 V. This input supply
should be able to withstand the maximum input current and maintain a voltage above 6 V. The resistance of the
input supply rail should be low enough that an input current transient does not cause a high enough drop at the
LM5576 supply voltage that can cause a false UVLO fault triggering and system reset. If the input supply is
located more than a few inches from the LM5576 additional bulk capacitance may be required in addition to the
ceramic bypass capacitors. The amount of bulk capacitance is not critical, but a 47-μF or 100-μF electrolytic
capacitor is a typical choice.
10 Layout
10.1 Layout Guidelines
The circuit in Figure 18 serves as both a block diagram of the LM5576 and a typical application board schematic
for the LM5576. In a buck regulator there are two loops where currents are switched very fast. The first loop
starts from the input capacitors, to the regulator VIN pin, to the regulator SW pin, to the inductor then out to the
load. The second loop starts from the output capacitor ground, to the regulator PGND pins, to the regulator IS
pins, to the diode anode, to the inductor and then out to the load. Minimizing the loop area of these two loops
reduces the stray inductance and minimizes noise and possible erratic operation. A ground plane in the PC
board is recommended as a means to connect the input filter capacitors to the output filter capacitors and the
PGND pins of the regulator. Connect all of the low power ground connections (CSS, RT, CRAMP) directly to the
regulator AGND pin. Connect the AGND and PGND pins together through the topside copper area covering the
entire underside of the device. Place several vias in this underside copper area to the ground plane.
The two highest power dissipating components are the re-circulating diode and the LM5576 regulator IC. The
easiest method to determine the power dissipated within the LM5576 is to measure the total conversion losses
(PIN – POUT) then subtract the power losses in the Schottky diode, output inductor and snubber resistor. An
approximation for the Schottky diode loss is P = (1-D) x IOUT x VFWD. An approximation for the output inductor
power is P = IOUT2 x R x 1.1, where R is the DC resistance of the inductor and the 1.1 factor is an approximation
for the AC losses. If a snubber is used, an approximation for the damping resistor power dissipation is P = VIN2 x
Fsw x Csnub, where Fsw is the switching frequency and Csnub is the snubber capacitor. The regulator has an
exposed thermal pad to aid power dissipation. Adding several vias under the device to the ground plane will
greatly reduce the regulator junction temperature. Selecting a diode with an exposed pad will aid the power
dissipation of the diode.
The most significant variables that affect the power dissipated by the LM5576 are the output current, input
voltage and operating frequency. The power dissipated while operating near the maximum output current and
maximum input voltage can be appreciable. The operating frequency of the LM5576 evaluation board has been
designed for 300 kHz. When operating at 3 A output current with a 70 V input the power dissipation of the
LM5576 regulator is approximately 2.5 W.
The junction-to-ambient thermal resistance of the LM5576 will vary with the application. The most significant
variables are the area of copper in the PC board, the number of vias under the IC exposed pad and the amount
of forced air cooling provided. Referring to the evaluation board artwork, the area under the LM5576 (component
side) is covered with copper and there are 5 connection vias to the solder side ground plane. Additional vias
under the IC will have diminishing value as more vias are added. The integrity of the solder connection from the
IC exposed pad to the PC board is critical. Excessive voids will greatly diminish the thermal dissipation capacity.
The junction-to-ambient thermal resistance of the LM5576 mounted in the evaluation board varies from 45°C/W
with no airflow to 25°C/W with 900 LFM (Linear Feet per Minute). With a 25°C ambient temperature and no
airflow, the predicted junction temperature for the LM5576 will be 25 + (45 x 2.5) = 137.5°C. If the evaluation
board is operated at 3 A output current and 70 V input voltage for a prolonged period of time the thermal
shutdown protection within the IC will activate. The IC will turn off allowing the junction to cool, followed by restart
with the soft-start capacitor reset to zero.
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
25
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
Layout Guidelines (continued)
One or more of the following modifications will prevent the thermal shutdown from being activated: apply forced
air cooling, reduce the maximum input voltage, lower the maximum output current, reduce the operating
frequency, add more heat sinking to the PC board. For example, applying forced air cooling of 225 LFM will
reduce the LM5576 thermal resistance to approximately 30°C/W. The junction temperature will be reduced to 25
+ (2.5 x 30) = 100°C. If the maximum input voltage for the application is 48 V, then the IC power dissipation
reduces to 2 W (at 3 A output current). With the same forced air cooling the junction temperature reduces to 25 +
(2 x 30) = 85°C.
10.2 Layout Example
Figure 28. Silkscreen
Figure 29. Component Side
26
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
LM5576, LM5576-Q1
www.ti.com
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
Layout Example (continued)
Figure 30. Solder Side
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
Submit Documentation Feedback
27
LM5576, LM5576-Q1
SNVS447J – JANUARY 2007 – REVISED NOVEMBER 2014
www.ti.com
11 Device and Documentation Support
11.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 2. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LM5576
Click here
Click here
Click here
Click here
Click here
LM5576-Q1
Click here
Click here
Click here
Click here
Click here
11.2 Trademarks
SIMPLE SWITCHER, WEBENCH are registered trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
28
Submit Documentation Feedback
Copyright © 2007–2014, Texas Instruments Incorporated
Product Folder Links: LM5576 LM5576-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
15-Apr-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
LM5576BLDT/NOPB
ACTIVE
LM5576MH
NRND
HTSSOP
LM5576MH/NOPB
ACTIVE
LM5576MHX/NOPB
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
0
1
TBD
Call TI
Call TI
PWP
20
73
TBD
Call TI
Call TI
-40 to 125
LM5576
MH
HTSSOP
PWP
20
73
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5576
MH
ACTIVE
HTSSOP
PWP
20
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5576
MH
LM5576Q0MH/NOPB
ACTIVE
HTSSOP
PWP
20
73
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM5576
Q0MH
LM5576Q0MHX/NOPB
ACTIVE
HTSSOP
PWP
20
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
LM5576
Q0MH
LM5576QMH/NOPB
ACTIVE
HTSSOP
PWP
20
73
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5576
QMH
LM5576QMHX/NOPB
ACTIVE
HTSSOP
PWP
20
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
LM5576
QMH
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(4)
15-Apr-2017
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM5576, LM5576-Q1 :
• Catalog: LM5576
• Automotive: LM5576-Q1
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LM5576MHX/NOPB
HTSSOP
PWP
20
2500
330.0
16.4
LM5576Q0MHX/NOPB
HTSSOP
PWP
20
2500
330.0
LM5576QMHX/NOPB
HTSSOP
PWP
20
2500
330.0
6.95
7.1
1.6
8.0
16.0
Q1
16.4
6.95
7.1
1.6
8.0
16.0
Q1
16.4
6.95
7.1
1.6
8.0
16.0
Q1
Pack Materials-Page 1
W
Pin1
(mm) Quadrant
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM5576MHX/NOPB
HTSSOP
PWP
20
2500
367.0
367.0
35.0
LM5576Q0MHX/NOPB
HTSSOP
PWP
20
2500
367.0
367.0
35.0
LM5576QMHX/NOPB
HTSSOP
PWP
20
2500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
PWP0020A
MXA20A (Rev C)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated