DDK BNC-P-3-CF Bnc style connector Datasheet

BNC Style Connector
BNC Series
OUTLINE
DDK’s 50 ohm BNC bayonet RF connector are
available in several configurations to support
Frequency
Range
DC to 2GHz
Characteristic
Impedance
50 Ω
a variety of design alternatives.
These BNC
connectors are available in straight, right angle and
panel mount configurations.
FEATURE
・BNC style 50 ohm RF connector
Lock Type
Bayonet
･50 ohm impedance design
･Quick mate/demate with reliable bayonet coupling
･High reliability interconnect for numerous connect and disconnect cycles.
･BNC 50 ohm connector is intermateable with BNC75 (75 ohm) style connector.
・BNC is capable of mating with 75 ohm cable for frequencies less than 200MHz.
・Frequencies higher than 200MHz should use DDK’s BNC75 series connector.
CONFORMING STANDARD
JIS-C-5412, MIL-PRF-39012, DSP-C-6202
SPECIFICATIONS
Characteristic Impedance
50 Ω
Dielectric Withstanding Voltage
1500V AC(r.m.s.) for 1 minute
Rated Voltage
500VAC(r.m.s.)
Insulation Resistance
1000M Ω Mim. at 500V DC
Contact Resistance
3m Ω Max.
V.S.W.R.
1.3 max. at DC to 2GHz
Operating Temperature
-55 〜 +85℃
＊ The specifications are typical but may not apply to all connectors.
And if the cable is not 50 Ω , the specification will be changed.
Please check the specifications on each item with its drawing from us when you use.
MATERIAL/FINISH
Item
RoHS
Compliant
Compliant
Material / Finish
Shell (Body)
Copper Alloy / Ni or Ag Plating
Contact (Male)
Copper Alloy / Ag or Au Plating
Contact (Female)
Copper Alloy / Ag or Au Plating
Insulator
PTFE
Gasket
Silicon Rubber
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
150116
http://www.ddknet.co.jp
BNC
Series
Unit：mm
○ Sraight Cable Plug
プラグ
3D-2V
3C-2V
3D-2V
BNC-P-3-Ni-CF
3C-2V
（L）
BNC-P-3-NiCAu-CF
RG-58/U
RG-55/U
BNC-P-58U-Ni-CF
RG-58/U
Ni
（L）
Ag
1
6.4 25.0
Ni
Au
1
5.4 27.0
Ag
Ag
1
5.4 27.0
Ni
Ag
1
BNC-P-62U-Ni-CF
RG-62/U
6.6 26,2
Ni
Ag
1
6.55 24.6
Ag
Ag
1
6.55 24.6
Ni
Ag
1
RG-59/U
RG-62/U
RG-59/U
RG-62/U
φA
Applicable
3D-2W
3C-2W
BNC-P-3W-Ni-1-CF
（31.7）
Finish
Assembly
Center
Instruction
Conductor Conductor
BNC-P-1.5CQEW-CR10
Cable
BNC-P-3W-CF
φ14.5
BNC-P-3W
3D-2W
3C-2W
φA （L）Outer
（L）
7.1 29.1
7.1
φ14.5
φ14.5
φ14.5
φA
φA
6.4 25.0
1
Part Number
（L）
1
Ag
UG-260/U-Ni-CF
φ14.5
φA
（L）
Ag
Ag
BNC-P-3W
BNC-P-1.5V-CR-CF
Ag
6.6 26.2
φA
BNC-P-3
6.4 25.0
RG-62/U
UG-260/U-CF
（L）
Assembly
Center
Instruction
Conductor Conductor
BNC-P-62U ー CF
φ14.5
φA
φ17.5
プラグ
3C-2V
RG-55/U
BNC-P-58U-CF
BNC-P-5
3D-2V
BNC-P-3W
Finish
φA （L）Outer
φ14.5
Cable
BNC-P-3-CF
φ14.5
φA
Applicable
Part Number
φA
Clamp Type
BNC-P-3
29.1
Ag
Ag
1
Ni
Ag
1
（L）
Cable
5D-2V
φ14.5
BNC-P-5-CF
（L）
φ14.5
φ14.5
φA
φA
5C-2V
BNC-P-5NiCAu-CF
5D-2V
5C-2V
5D-2W
BNC-P-5W-CF
BNC-P-1.5V-CR-CF
BNC-P-1.5CQEW-CR10
5D-2V
BNC-P-5-Ni-CF
8.6
37.0
Ag
Ag
1
8.6
37.0
Ni
Ag
1
8.6
37.0
Ni
Au
1
9.2
37.0
Ag
Ag
1
9.2
37.0
Ni
Ag
1
BNC-P-1.5CQEW-CR10
5C-2W
5D-2W
BNC-P-5W-Ni-CF
φA
φA
（L）
5C-2V
（31.7）
5C-2W
Finish
Assembly
Center
Instruction
Conductor Conductor
φA （L）Outer
φ14.5
BNC-P-3C-CR1
Applicable
Part Number
φ14.5
φA
φ17.5
BNC-P-5
（L）
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
（L）confirm the content with the latest delivery specifications when you use the product.
Please
http://www.ddknet.co.jp
2
BNC-P-3C-CR1
φ14.5
φA
φ17.5
BNC-P-5
BNC
Series
Unit：mm
BNC-P-3W
○ Straight Cable Plug
Crimp Type
（L）
BNC-P-3W
Applicable
Part Number
Cable
（L）
BNC-P-1.5CQEW-CR10
φA
1.5D-2V
BNC-P-1.5V-CR-CF
（31.7）
1.5C-2V
1.5D-2V
φA
φ14.5
φA
φA
φ14.5
BNC-P-1.5V-CR-CF
BNC-P-1.5V-CR-Ni-CF
1.5C-2V
1.5D-2V
（L）
BNC-P-1.5V-CR-NiCAu-CF
1.5C-2V
2.5D-2V
BNC-P-2.5V-CR-CF
2.5C-2V
2.5D-2V
BNC-P-2.5V-CR-Ni-CF
2.5C-2V
BNC-P-5
BNC-P-3C-CR1
2.5D-2V
φA
φA
φ14.5
φ14.5
BNC-P-2.5V-CR-NiCAu-CF
φ17.5
Finish
Assembly
Outer
Center
Instruction
Conductor Conductor
φA
2.5C-2V
5.5
Ag
5.5
（L）
Crimp Tool
Ag
3
CR-H-1100
φ14.5
BNC-P-3
φ14.5
φA
プラグ
φ14.5
（L）
Ni
Ag
3
CR-H-1100
5.5
Ni
Au
3
CR-H-1100
5.5
Ag
Ag
3
CR-H-1100
5.5
Ni
Ag
3
CR-H-1100
5.5
Ni
Au
3
CR-H-1100
BNC-P-179U-CR-CF
RG-179/U
5.5
Ag
Ag
3
CR-H-1100
BNC-P-179U-CR-Ni-CF
RG-179/U
5.5
Ni
Ag
3
CR-H-1100
Cable
BNC-P-1.5CQEW-CR10-CF
1.5C-QEW
BNC-P-58U-CR10-CF
（31.7）
24.3
Crimp
Tool
Note
Ni
Au
ー
CR-H-1100
BNC-P-1.5CQEW-CR10
4.0
23.3
Ni
Au
4
CR-H-1120A Delta-mate
1.5D-QEW
BNC-P-3C-CR10-BOOT-CF
BNC-P-3D-CR10-BOOT-CF
5.5
Finish
Assembly
Center
Instruction
Conductor Conductor
φA （L）Outer
1.5D-XV
BNC-P-1.5D-CR10-CF
φ14.5
φA
Applicable
Delta-mate
3C-2V
7.1
24.3
Ni
Au
4
CR-H-1116
Delta-mate
3D-2V
7.1
24.3
Ni
Au
4
CR-H-1116
Delta-mate
6.3
RG-58A/U（L）
24.3
Ni
Au
4
CR-H-1115
Delta-mate
24.3
Ni
Au
4
CR-H-1116
Delta-mate
RG-58/U
BNC-P-3D-CR10-CF
3D-2V
7.1
φ14.5
BNC-P-1.5V-CR-CF（L）
Part Number
φA
φA
φ14.5
（L）
（L）
BNC-P-1.5CQEW-CR10
φA
φ14.5
BNC-P-3C-CR1
（L）
Part Number
Applicable
Cable
Finish
Assembly
Center
Instruction
Conductor Conductor
φA （L）Outer
Crimp
Tool
BNC-P-3C-CR1-CF
3C-2V
7.0
28.0
Ag
Ag
2
CR-H-1102
BNC-P-3C-CR1-Ni-CF
3C-2V
7.0
28.0
Ni
Ag
2
CR-H-1102
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
3
BNC-LP-3
BNC
Series
Unit：mm
80%
○ Right Angle Cable Plug
BNC-LP-5
Clamp Type
Cable
3D-2V
3C-2V
3D-2V
（27）
（25）
BNC-LP-3-CF
BNC-LP-3-CAu-CF
3C-2V
3D-2V
BNC-LP-3-NiCAu-CF
φA
3D-2V
BNC-LP-3-Ni-CF
3C-2V
RG-55/U
BNC-LP-58U-CF
BNC-LP-5
RG-58/U
RG-55/U
BNC-LP-58U-Ni-CF
ジャック BNC-J-3
パネルジャック
BNC-PJ-3
RG-58/U
RG-55/U
φA
BNC-LP-55U-CF
ライトアングルプラグ
3C-2V
（33）
（33）
0%
4-φB
RG-58/U
Finish
Assembly
Center
Instruction
Conductor Conductor
φA Outer
6.4
Ag
Ag
5
6.4
Ag
Au
5
6.4
Ni
Au
5
6.4
Ni
Ag
5
5.38
Ag
Ag
6
5.38
Ni
Ag
6
5.4
Ag
Ag
6
BNC-LP-5
Applicable
φA
（L）
2.3
（27）
12.7
80%
BNC-LP-3
Part Number
15.8
（L）
BNC-LP-5-CF
Cable
12.7
5D-2V
○ Straight Cable Jack
φA
5C-2V
Center
Conductor
Assembly
Instruction
Ag
Ag
7
Ni
Au
7
12.7±0.05
（27）
（25）
+0.1
φ11.5 0
パネルジャック
5D-2V
4-φ3.0 0
BNC-LP-5-Ni-CF
（33）
Finish
Outer
Conductor
5C-2V
+0.1
-3
12.7±0.05
（33）
BNC-PJ-3
（33）
Clamp Type
Part Number
4-φB
3D-2V
BNC-J-3-CF
+0.1
φA
12.7±0.05
+0.1
φ11.5 0
BNC-J-3-Ni-CF
2.3
6.4
3C-2V
4-φ3.0 0
（L）
φA
Cable
15.8
BNC-J-58U-CF
（L）
3D-2V
3C-2V
RG-55/U
12.7
RG-58/U
Finish
Assembly
Center
Instruction
Conductor Conductor
(L) Outer
28.5
Ag
Ag
1
6.4
28.5
Ni
Ag
1
5.4
28.6
Ag
Ag
1
12.7
12.7
BNC-PJ-3
Applicable
□17.5
パネルジャック
φA
（L）
15.8
12.7
ジャック BNC-J-3
2.3
□17.5
4-φB
+0.1
4-φ3.0 0
12.7±0.05
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
+0.1
Please confirm the content with the latest delivery specifications
when
0 you use the product.
φ11.5
12.7±0.05
φA
）
Applicable
Part Number
□17.5
ライトアングルプラグ
http://www.ddknet.co.jp
4
12.7±0.05
（33）
BNC
Series
Unit：mm
○ Straight Panel Cable Jack
Clamp Type
パネルジャック
BNC-PJ-3
4-φB
（L）
15.8
Cable
3C-2V
3D-2V
BNC-PJ-3-Ni-CF
12.7
3C-2V
RG-55/U
BNC-PJ-58U-CF
+0.1
RG-58/U
4-φ3.0 0
RG-55/U
12.7±0.05
BNC-PJ-58U-Ni-CF
+0.1
φ11.5 0
φA φB
3D-2V
BNC-PJ-3-CF
□17.5
12.7
φA
2.3
Applicable
Part Number
RG-58/U
BNC-PJ-58U-NiCAu-CF
RG-55/U
RG-58/U
Finish
Assembly
Center
Instruction
Conductor Conductor
(L) Outer
6.4
3.0
28.5
Ag
Ag
1
6.4
3.0
28.5
Ni
Ag
1
5.4
3.0
28.5
Ag
Ag
1
5.4
3.0
28.5
Ni
Ag
1
5.4
3.0
28.5
Ni
Au
1
12.7±0.05
Panel Mounting Dimensions
○ Receptacle Jack
BNC-R-CF
レセプタクル
+0.1
4-φ3.0 0
15.8
26.3
4-φB
BNC-LR-Ni
2.3
+0.1
4-φ3.0 0
12.7±0.05
+0.1
φ9.0 0
□17.5
12.7
Ni
Ag
Ag
Ag
UG-290/U-Ni-1-CF
M2.6
Ni
Ag
4-φ3.2
Part Number
12.7
φ9.0
+0.1
5-φ1.2 0
10.16±0.05
2.3
13.3
10.16±0.05
2.5
5.08±0.025
□15.0
2.3
+0.1
10.16 0
5
Finish
Center
Outer
Conductor Conductor
BNC-LR-CF
Ag
Ag
BNC-LR-Ni-CF
Ni
Ag
12.7
5.08±0.025
□15.0
3.1
M2.6
◎ Please acknowledge that the specification etc. of+0.1
this catalog might change by the improvement etc. without notice.
13.3
2.5characteristic
5-φ1.2 0of the published product are the reference values.
Moreover, the
and the specification
5.08±0.05
Please confirm the content with the latest delivery specifications
when you use the product.
http://www.ddknet.co.jp
Ag
BNC-R-Ni-CF
Panel Mounting Dimensions
BNC-R-PC-4
Ag
UG-290/U-CF
12.7
23
□17.5
12.7
3.1
12.7
23
φ9.0
23
23
Center
Conductor Conductor
4-φ3.2
4-φ3.0
BNC-R-PC-4
Finish
12.7±0.05
BNC-LR-Ni
12.7
φB Outer
Panel Mounting Dimensions
12.7
4-φ3.0
□17.5
15.8
26.312.7
BNC-R-CF
12.7±0.05
+0.1
φ9.0 0
12.7
□17.5
12.7
φ1.4
2.3
12.7
BNC-R-CF
レセプタクル
Part Number
12.7±0.05
φ1.4
4-φB
12.7
Series
○ Receptacle Jack
φ9.0
23
□17.5
12.7
BNC
Unit：mm
12.7
23
BNC-R-PC-4
10.16±0.05
2.3
13.3
2.5
Finish
Part Number
5.08±0.025
□15.0
+0.1
5-φ1.2 0
Center
Outer
Conductor Conductor
Note
BNC-R-PC-4-Ag-CF
Ni
Ag
Board lock is
Ag plating
BNC-R-PC-4-D1-CF
Ni
Au
Board lock is
Ag plating.
5.08±0.05
+0.1
10.16 0
PCB Mounting Dimensions
レセプタクル -2
BNC-LR-PC-4-Ag
23
BNC-LR-PC-4-Ag
2.5
Center
Outer
Conductor Conductor
Note
BNC-LR-PC-4-Ag-CF
Ni
Ag
Board lock is
Ag plating
BNC-LR-PC-4-NiCAu-CF
Ni
Au
Board lock is
Ag plating
5.08±0.025
+0.1
10.16 0
10.16±0.05
+0.1
±0.05
5.08
5-φ1.2 0
19.1
10.16
PCB Mounting Dimensions
23
□15.0
10.16
10.16±0.05
レセプタクル -2
Finish
Part Number
5.08±0.025
+0.1
5-φ1.2 0
10.16
□15.0
10.16
BNC-PR
2.5 4-φ3.0
+0.1
0
4-φ3.0±0.05
5.08
φ1.1
19.1
+0.1
+0.1
（17.7）
（28.2）
φ9.0 0
12.7
4-φ3.0
□17.5
2.3
+0.1
（17.7）
（28.2）
φ9.0 0
12.7
Ag
BNC-PR-Ni-CF
Ni
Ag
Hex Dia.12.7
φ1.4
BNC-625/U
Hex Dia.12.7
10.3
26.3
1.5
12.6
φ12.7
BNC-RB2
Ag
Panel Mounting Dimensions
+0.1
φ11.3 0
26.3
1.5
26.3
+0.1
φ11.3 0
12.6
Hex Dia.12.7
10.3
BNC-625/U
φ12.7
φ1.4
◎ Please acknowledge that 1.5
the specification etc. of this+0.1
catalog might change by the improvement etc. without notice.
φ11.3 0
Moreover, the characteristic
and the specification of the published product are the reference values.
12.6
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
6
Finish
Outer
Center
Conductor Conductor
BNC-PR-CF
12.7±0.05
φ12.7
φ1.4
Hex Dia.12.7 □17.5
バルクヘッドレセプタクル
Part Number
12.7±0.05
12.7
バルクヘッドレセプタクル
BNC-RB2
+0.1
4-φ3.0 0
12.7±0.05
φ1.1
2.3
10.3
BNC-PR
12.7±0.05
12.7
10.16 0
12.7
φ9.0 0
12.7±0.05
□17.5
BNC
+0.1
φ9.0 0
□17.5
12.7
Series
12.7±0.
1
（17.7）
（28.2）
2.3
（17.7）
（28.2）
12.
2.3
Unit：mm
12.7±0.05
バルクヘッドレセプタクル
○ Straight Bulkhead Cable Jack
BNC-RB2
バルクヘッドレセプタクル
BNC-RB2
φ1.4
Hex Dia.12.7
26.3
26.3
BNC-625/U
1.5
12.6
+0.1
φ11.3 0
Panel Thickness：1.2 〜 3.5
BNC-625/U
10.3
+0.1
φ11.3 0
10.3
φ12.7
φ1.4
φ12.7
Hex Dia.12.7
1.5
12.6
Finish
Part Number
Outer
Center
Conductor Cnductor
BNC-RB2-CF
Ag
Ag
BNC-RB2-Ni-CF
Ni
Ag
BNC-RB2-NiCAu-CF
Ni
Au
Panel Mounting Dimensions
φ1.4
Hex Dia.12.7
26.3
+0.1
φ11.3 0
1.5
10.3
26.3
10.3
1.5
12.6
Finish
Part Number
φ12.7
φ1.4
φ12.7
Hex Dia.12.7
+0.1
φ11.3 0
12.6
Outer
Center
Conductor Conductor
UG-625/U-CF
Ag
Ag
UG-625/U-Ni-CF
Ni
Ag
Panel Thickness：1.2 〜 3.5 Panel Mounting Dimensions
バルクヘッドレセプタクル -3
UG-604/U
バルクヘッドレセプタクル -3
+0.1
Hex Dia.12.7
φ14.3
φ1.1
φ9.6 0
1.0
13.7
26.3
Hex
1.0Dia.12.7
Finish
Part Number
+0.1
Hex Dia.12.7
バルクヘッドレセプタクル -3
UG-604/U
φ9.6 0
φ14.3
φ1.1
UG-604/U
Outer
Center
Conductor Conductor
UG-604/U-CF
UG-604/U-Ni-1-CF
+0.1
8.5 0
+0.1
13.7
Hex Dia.12.7
26.3
φ1.3
33
UG-1094/U
Hex 2.44
Dia.12.7
15.1
33
Hex Dia.12.7
+0.1
8.5 0
+0.1
φ9.92 0
+0.1
8.5 0
Part Number
Finish
Outer
Center
Conductor Conductor
UG-657/U-CF
Ag
Ag
UG-657/U-Ni-CF
Ni
Ag
Note
Independent
Waterproof
with Frange O-ring
Independent
Waterproof
with Frange O-ring
φ1.3
BNC-RBP1Panel
+0.1
φ9.6 0
+0.1
+0.1 8.8 0
8.8 0
φ12.7
φ12.7
1.2
Hex11.9
Dia.12.7
27
2.5
Thickness：2.2
〜
15.2
32.6
Hex
Dia.12.7
2.5
+0.1
φ9.6 0
+0.1
8.5 0
+0.1
φ9.6 0
+0.1
φ9.6 0
+0.1
8.8 0
φ1.3
BNC-RBP1
φ12.7
φ1.6
BNC-RBP1
φ14.5
UG-1094/U
2.44
Hex Dia.12.7
15.1
33
1.2
11.9
27
1.2Dia.12.7
Hex
11.9
27
Hex Dia.12.7
φ14.5
φ1.6
Panel Thickness：2.2 〜 6.0 Panel Mounting Dimensions
φ1.6
UG-1094/U
2.44
15.1
+0.1
+0.1
8.5 0 φ9.92 0
φ14.5
φ1.3
UG-657/U
+0.1
φ9.92 0
φ14.5
1.0
8.5 0
φ14.3
φ1.3
UG-657/U
Part Number
Ag
Ag
UG-1094/U-D1-CF
Ni
Au
+0.1
φ9.6 0
+0.1 Dimensions
3.1 Panel Mounting
8.5 0
+0.1
φ9.6 0
φ14.5
φ1.3
http://www.ddknet.co.jp
4.4
4.7
2.5
Hex Dia.12.7
15.2
32.6
Hex Dia.12.7
+0.1
+0.1 0
φ9.6
8.5 0
7
+0.1
Finish
Outer
Center
Conductor Conductor
UG-1094/U-CF
+0.1 might change by the improvement etc. without notice.
◎ Please acknowledge that the specification etc. of this catalog
15.2
8.5 0
Moreover, the
characteristic and the specification of the published product are the reference values.
32.6
Please confirm the content with the latest delivery specifications when you use the product.
φ1.1
Ag
φ9.6 0
φ14.5
φ1.1
26.3
Hex Dia.12.7
BNC-RB
Ag
Ni
Panel Thickness：0.7
〜 2.4 Panel Mounting
13.7
+0.1Dimensions
UG-657/U
BNC-RB
Ag
UG-1094/U
UG-1094/U
+0.1
+0.1
Series
1.2
○ Straight Bulkhead
Cable Jack
1.2
+0.1
0
φ9.6+0.1
φ9.6 0
11.9
2711.9
27
BNC-RBP1
BNC-RBP1
+0.1
φ1.3
φ1.3
φ14.5
φ14.5
+0.1
0
8.5+0.1
8.5 0
Ag
Ag
BNC-RBP1-Ni-CF
Ni
Ag
0
φ9.6
+0.1
φ9.6 0
φ14.4
φ14.4
φ14.7
φ14.7
φ1.1
φ1.1
BNC-RBP1-CF
+0.1
Hex Dia.12.7
Hex Dia.12.7
2.3
2.3
17.4
33 17.4
33
Finish
Outer
Center
Conductor Conductor
Note
Independent
Waterproof
with Frange O-ring
Independent
Waterproof
with Frange O-ring
Panel Mounting Dimensions
Panel Thickness：2.6 〜 6.4
BNC-RB
BNC-RB
Part Number
0
φ9.6
+0.1
φ9.6 0
Hex Dia.12.7
Hex Dia.12.7
2.5
2.5
15.2
32.615.2
32.6
Unit：mm
0 0
8.8
8.8
BNC
φ12.7
φ12.7
φ1.6
φ1.6
Hex Dia.12.7
Hex Dia.12.7
+0.1
Part Number
Finish
Outer
Center
Conductor Conductor
Note
BNC-RB-CF
Ag
Ag
with Frange O-ring
BNC-RB-Ni-CF
Ni
Ag
with Frange O-ring
0
8.5+0.1
8.5 0
Panel Thickness：2.2 〜 7.0 Panel Mounting Dimensions
○ Dust Cap
Marking
JCW-159/U-CF/DDK
(17.8)
(57)
(90)
(20.5)
)
.7
3
表示
(φ
BNC-JC-CF/DDK
Part Number
Finish
Part Number
Finish
BNC-CS-CF
Ag
Short Cap
BNC-JC-CF
Ag
BNC-CS-Ni-CF
Ni
Short Cap
BNC-JC-Ni-CF
Ni
（φ3.5）
Part Number
BNC style mating side
適合コネクタ：BNC形プラグ
60±5
(75)
Finish
BNC-RC-3
Ni
BNC-RC-3-D1
Ag
Marking：DDK
BNC-JC-CF
2582-CF
BNC-CS-CF
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
2559-CF
Please confirm the content with the latest delivery specifications
when you use the product.
http://www.ddknet.co.jp
8
BNC
Series
Unit：mm
○ Assembly Instruction（1）
Parts Configulration
MIL Clamp
MIL
Clamp
Clamp
Gasket
Gasket
Nut
Nut
Washer
Washer
Clamp
Gasket
Gasket
Clamp
Clamp
Male Contact
Male Contact A
Plug Body
Plug Body
Female Contact
Jack Body
Jack Body
① Cut the cable as fig.1.
A
①
Female Contact
Please be carefule to not damage the outer
conductor.
Applicable Cable
Washer Gasket
Clamp
Nut
Washer Gasket
Clamp
Nut
A
5D-2V, RG-59/U, RG-62/U
②
10mm
3D-2V, 5D-2W
RG-55/U, RG-58/U
15mm
3D-2W
12mm
② Insert the nut, washer, gasket and clamp.
● The clamp is located on the outer conductor of the
cable. Pick the outer conductor.
③ Cut the insulator and center conductor as fig.3.
Fold up the outer conductor to the clamp equally and
C
③
cut the outer conductor of the cable along the clamp
B
C
as fig.3.
● Please be careful to not damage the center conductor.
B
No Gap
④
Applicable Cable
Soldering
No Gap
Soldering
3D-2V, 3D-2W,
RG-55/U, RG-58/U
Contact
5D-2V
Contact
B
C
6mm
3mm
7mm
5mm
RG-59/U, RG-62/U
5.5mm
3mm
5D-2W
7.2mm
5.4mm
④ Solder up the contact to the center conductor.
● Please be careful to not be swelled up the solder.
● Please be careful to not gap between contact and
⑤
insulator.
● Please be careful to not deform the insulator by
Body
Cable assembly
soldering
Body
Cable assembly
⑤ Insert the body into the above cable assembly and
screw up the nut.
● Please screw up the nut by wrench tightly.
Hex Dia.：９．
５
Dia.：９．
５
Hex Dia.：９．
５
Dia.：９．
５
Applicable Cable
Recommended Tightening Torque
3D-2V, RG-55/U, RG-58/U
117.6 〜 147N・cm(12 〜 15kgf・cm)
RG-59/U, RG-62/U, 3D-2W
196N・cm(20kgf・cm)
5D-2V
441N・cm(45kgf・cm)
5D-2W
490 〜 686N・cm(50 〜 70kgf・cm)
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
9
BNC
Series
Unit：mm
○ Assembly Instruction（2）
Parts Configulration
Boot
Boot
Ferule
Ferule
Center Conductor
Center Conductor
Body
Body
15mm
① Insert the boot, ferule into the cable and cut the
①
15mm
cable as fig.1.
●
Please be careful to not damage the outer
conductor.
13.3mm
②
② Cut the insulator and outer conductor as fig.2.
13.3mm
●
6.6mm
10.6mm
Pre-solder the center conductor and cut as fig.2.
When cutting the insulator, please be careful to not
damage the center conductor.
6.6mm
10.6mm
③ Solder up the contact to the center conductor.
③
Spread the end of the outer conductor to insert the
body between insulator and outer conductor easily.
Please do not pick the outer conductor.
● Please be caredule to not be swelled up the solder.
Shave the excessed solder along the outside of the
contact.
● Please be careful to not deform the insulator by
soldering.
④
④ Insert the body into the cable between insulator and
outer conductor until the top of the contact is on the
Edge of Crimp Dies
same
plane
Edge
of Body
Edge of Crimp Dies
A
B
Edge of Body
B
A
with the top of the body and move the
ferule
to
the
body. Crimp the ferule at position A
0.5～1.0mm
and position B .
0.5～1.0mm
⑤
⑤ Cover the boot on the ferule.
Boot
Boot
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
10
BNC
Series
Unit：mm
○ Assembly Instruction（3）
Parts Configulration
（for 2.5D-2V）
（for 2.5D-2V）
(for 1.5D-2V / RG-179B/U)
(for 1.5D-2V / RG-179B/U)
Ferule
Contact Assembly
Ferule
①
● Please be careful to not damage the outer conductor.
Inserting Tool
Ferule
Inserting Tool
Ferule
2.5D-2V
Plug Body
① Cut the cable as fig.1.
20mm
20mm
②
Plug Body
Contact Assembly
② Insert the ferule.
● In case of 2.5D-2V cable, insert the ferule into the cable
and push the ferule between sheath and outer conductor
until the head of ferule is reached to the sheath by
2.5D-2V
inserting tool(E3001-160) and pick the outer conductor.
● In case of 1.5D-2V or RG-179B/U cable , insert the
Ferule
1.5D-2V,RG-179B/U
ferule until the ferule reached at the sheath and pick the
Ferule
1.5D-2V,RG-179B/U
outer conductor.
cut the couter conductor along the ferule as fig.3.
Cut the insulator and center conductor and pre-solder
10mm
17mm
A
③
③ Folding down the outer conductor to the ferule and
17mm
A
10mm
the center conductor.
Applicable Cable
④
A
2.5D-2V
4mm
1.5-2V, RG-179B/U
5mm
Soldering
Soldering
④ Insert the contact assembly into the above cable
assembly. Solder up the contact with center conductor
1mm
1mm
crimping
and crimp the root of the contact assembly.
crimping
⑤ Insert the body into the above cable assembly and
⑤
screw up the body by the wrench tightly.
Recommended Tightening Torque : 196 N･cm(20kgf･cm)
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
11
BNC
Series
Unit：mm
○ Assembly Instruction（4）
Parts Configulration
Crimp
Crimp area
Bayonet
Body
Crimp
Ferule
Contact
BNC-P mating side
(24.3)
(24.3)
① Cut the cable as fig.1.
L
Cable
L
Cable
②
L Amm=Lmm-12mm
② Remove the sheath
LA
●
LA
15
15
Sleeve CR-H-1115
Ferule
CR-H-1116
Sleeve
B
B
CR-H-1120A
Attachment
conductor.
89141
⑤
diging the edge.
④ Cut the center conductor by stripper as fig.4.
B
Stripper
conductor. Plunge the sleeve by stripper without
89134
C
C
Please be careful to not damage the outer
③ Insert the ferule and spread the tip of the outer
Assembly Tool
Ferule
④
(24.3)
BNC-P mating side
(24.3)
(24.3)
③
Delta-mate Outer Conductor
(24.3)
*The insulator
is attached
*Insulator
Ferule
Sleeve with BNC-P-1.5D-CR10-CF.
Contact
Please cover the sheath when crimping the contact.
①
Insulator
Delta-mate Outer Conductor
Crimp area
*Insulator
Sleeve
Insulator
Bayonet
Body
⑤ Cut the insulator by stripper as fig.5.
Insert the stripper and dig the edge to the
B
insulator. Rotate the stripper a few times and pull
Stripper
A
D
A
off the insulator.
⑥ Trim the extra outer conductor along the sleeve.
D
⑦ Put the contact into the crimp tool attachment and
⑥
insert it into the crimp dies as fig.7. Insert the
⑦
center conductor into the contact hole and crimp
the contact with touching the contact brim to the
end of sheath.
⑧
⑧ Insert the above contact assembly into the body
until the top of contact is same plane as rim
dies
dies
⑨
of outer conductor.
● After the contact brim is inserted into the body,
do not rotate the cable and body.
⑨
⑨ Put the above cable assembly in the crimp tool and
crimp the root of the body.
● Please match the hex of dies with the hole of the
body.
for CR-H-1120A
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
12
Nut2
BNC
Series
Unit：mm
○ Assembly Instruction（5）
Nut1
Washer
Parts Configulration
Nut1
Clamp
Gasket
Washer
Gasket
Body Assembly
Clamp
Cable
Nut2
Body Assembly
Cable length require for the single ended cable assembly
L =L1+0.3
①
Cable
L1
Washer
Sheath
Outer Conductor
（Pre-soldering）
L1
Nut1
Gasket
Washer
Sheath
1-1.Cut the cable as fig.1.
1-2. Pre-sollder the center conductor.
Note）Please be careful to not damage the outer
conductor.
1-3．Insert the nut 1, washer and gasket.
Center Conductor
2±0.3
8±0.3
Outer Conductor
Center Conductor
（Pre-soldering）
②
Cut the outer conductor
Sheath
along the clamp
Cable Assembly
2-1.Insert the clamp into the outer conductor and
put it on the sheath.
2-2. Pick the outer conductor and fold down to the
clamp and cut the extra outer conductor along
the clamp.
8±0.3
Insulator
Gasket
Sheath
Clamp
③
2±0.3
Clamp
Nut1
Outer conductor
Insulator
Nut1
Cut the outer conductor
along the clamp
9.5
（Hex Dia.）Nut1
Cable Assembly
Outer conductor
3-1.Insert the above cable assembly into the body.
3-2.Screw up the nut1 to the body.
Recommended screw toque：117.6 〜 147N・㎝
（12 〜 15kgf・㎝）
□12.7
Body Assembly
④
9.5
（Hex Dia.）
Body Assembly
Center Conductor
Nut2
□12.7
Soldering
Nut2
Contact
Center Conductor
4-1.Solder up the contact with the center
conductor
4-2.Screw up the nut2 to the body.
Recommended screw torque：49N・㎝
（5kgf・㎝）
Soldering
Body Assembly
Contact
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
Body Assembly
13
BNC
Series
Unit：mm
○ Assembly Instruction(6）
Parts Configulration
Nut1
Washer
Gasket
Clamp
Nut2
Nut1
Washer
Gasket
Clamp
Body Assembly
Nut2
Body Assembly
The cable length require for the single ended cable
assembly.
L1 =L+3.3
Cable
Cable
L
①
Nut1
Washer
L
Gasket
Outer Conductor
Nut1
Washer
Gasket
Outer Conductor
Cable
1-2. Cut the cable as fig.1.
Note）Please be careful to not damage the outer
conductor.
11
Cable
②
1-1.Insert the nut1, washer and gasket.
2-1.Insert the clamp into the outer conductor and
move to the sheath.
11
Clamp Insulator
Clamp Insulator
(3)
2-2.Pick the outer conductor equally. Fold down to
Center Conductor
(Pre-soldering)
Center Conductor
(Pre-soldering)
2 ±0.3
the clamp and cut the extra outer conductor
along the clamp.
3-3.Cut the insulator as fig. 2.
2-4.Pre-solder the center conductor and cut the
center conductor as fig.2.
±0.3
5 ±0.3
Cut the outer conductor
2
(3)
along the clamp
5 ±0.3
Cut the outer conductor
along the clamp
Contact Slit
③
3-1.Insert the above contact assembly into the
Contact Slit
Cable Assembly
Cable Assembly
body assembly.
Note）The center conductor is located in the
□12.7
center of contact slit.
3-2.Move the nut1, washer and gasket to the body.
□12.7
3-2.Screw up the nut1 to the body.
Recommended screw torque：117.6 〜 147N・㎝
9.52
(Hex Dia.)
9.52
Body
Assembly
(Hex
Dia.)
④
（12 〜 15kgf・㎝）
Body Assembly
4-1.Solder up the contact with center conductor.
Soldering
Soldering
⑤
Nut2
5-1.Screw up the nut2 to the body.
Recommended screw torque：49N・㎝ min.
（5kgf・㎝ min.）
Nut2
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
14
BNC
Series
Unit：mm
○ Assembly Instruction（7）
Nut２
Parts Configulration
Nut２
Washer１
Nut１
Washer２
Body Assembly
Washer２
Clamp
Body Assembly
Clamp
Washer１
Nut１
The cable length require for the single ended
cable assembly ：L1
L1 =L+3
Ｌ
Ｌ
Sheath
①
1-1.Cut the cable as fig.1.
Sheath
Outer Conductor
Note）Please be careful to not damage the outer
conductor.
15 ±0.5
Cable
②
Outer Conductor
Nut１
Clamp
Cable
Washer１
Clamp
Washer１
Nut１
2-1.Insert the nut1, washer1 and insert the clamp
15 ±0.5
Outer Conductor
on the outer conductor and move to the
Outer Conductor
sheath.
2-2. Fold down to the clamp and cut the extra
outer conductor in 3 mm from the clamp.
2-3.Move the washer 1 and nut 1 to the clamp.
3
Washer２
③
Insulator
3
Outer Conductor
Washer２
Insulator
（Pre-soldering）
Outer Conductor
3-1.Insert
（Pre-soldering）
washer 2 on the outer conductor and cut
the insulator as fig.3.
+0.5
0
5.7 0
+0.5
Contact Slit
④
4 -0.5
5.7 0
0
4 -0.5
Contact Slit
4-1.Insert the above cable assembly into the
bodyassembly and screw up the nut 1.
Recommended screw torque：196N・㎝（20kgf・㎝）
Note）The center conductor is located in the
Body Assembly
center of contact slit.
Body Assembly
Nut２
⑤
3-2. Pre-solder the center conductor and cut the
center conductor as fig.3.
Soldering
Nut２
5-1.Solder
Soldering
up the contact with center conductor.
5-2.Screw up the nut 2 to the body.
Recommended screw torque：49N・㎝（5kgf・㎝）
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
Moreover, the characteristic and the specification of the published product are the reference values.
Please confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
15