HRP-75 75W Single Output with PFC Function series Features : Universal AC input / Full range Built-in active PFC function Withstand 300VAC surge input for 5 seconds Protections: Short circuit / Overload / Over voltage Protections: Over temperature (optional) Cooling by free air convection 1U low profile 38mm Built-in remote ON-OFF control No load power consumption<0.5W All using 105 long life electrolytic capacitors 5 years warranty SPECIFICATION MODEL OUTPUT HRP-75-3.3 HRP-75-5 HRP-75-7.5 HRP-75-12 HRP-75-15 HRP-75-24 HRP-75-36 HRP-75-48 DC VOLTAGE 3.3V 5V 7.5V 12V 15V 24V 36V 48V RATED CURRENT 15A 15A 10A 6.3A 5A 3.2A 2.1A 1.6A CURRENT RANGE 0 ~ 15A 0 ~ 15A 0 ~ 10A 0 ~ 6.3A 0 ~ 5A 0 ~ 3.2A 0 ~ 2.1A 0 ~ 1.6A RATED POWER 49.5W 75W 75W 75.6W 75W 76.8W 75.6W 76.8W RIPPLE & NOISE (max.) Note.2 80mVp-p 80mVp-p 100mVp-p 120mVp-p 150mVp-p 150mVp-p 200mVp-p 240mVp-p VOLTAGE ADJ. RANGE 4.7 ~ 5.8V 2.5% 7.1 ~ 9V 2.5% 11 ~ 13.8V 1.5% 14.2 ~ 18V 1.5% 21.6 ~ 28.8V 1.5% 32 ~ 39.6V 1.5% 45 ~ 55.2V 1.5% VOLTAGE TOLERANCE Note.3 3.1 ~ 3.8V 2.5% LINE REGULATION 1.0% 1.0% 1.0% 0.3% 0.3% 0.2% 0.2% 0.2% LOAD REGULATION 2.0% 2.0% 1.5% 1.0% 0.5% 0.5% 0.5% 0.5% SETUP, RISE TIME 1800ms, 25ms/230VAC HOLD UP TIME (Typ.) 50ms/230VAC VOLTAGE RANGE Note.5 85 ~ 264VAC 47 ~ 63Hz FREQUENCY RANGE INPUT POWER FACTOR (Typ.) PF>0.9/230VAC EFFICIENCY (Typ.) 77% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 1.2A/115VAC 35A/115VAC LEAKAGE CURRENT <1mA / 240VAC OVERLOAD PROTECTION OVER VOLTAGE FUNCTION 1800ms, 25ms/115VAC at full load 20ms/115VAC at full load 120 ~ 370VDC PF>0.95/115VAC at full load 82.5% 84% 87% 88% 88.5% 89% 89% 0.7A/230VAC 65A/230VAC 105 ~ 135% rated output power Protection type : Constant current limiting, switch to hiccup mode for Vo<50% of rated voltage, recovers automatically after fault condition is removed 6 ~ 7V 9.4 ~ 10.9V 14.4 ~ 16.8V 18.8 ~ 21.8V 30 ~ 34.8V 41.4 ~ 48.6V 57.6 ~ 67.2V 3.96 ~ 4.62V Protection type : Shut down o/p voltage, re-power on to recover 85 5 for 3.3V~15V; 80 5 for 24V~48V (TSW1 : detect on heatsink of power transistor) (optional) OVER TEMPERATURE (OPTIONAL) Protection type : Shut down o/p voltage , recovers automatically after temperature goes down RC+ / RC-: 0 ~ 0.8V = power on ; 4 ~ 10V = power off REMOTE CONTROL -20 ~ +70 (Refer to output load derating curve) WORKING TEMP. 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT 0.03%/ (0 ~ 50 VIBRATION 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 approved SAFETY STANDARDS SAFETY & EMC (Note 4) OTHERS WITHSTAND VOLTAGE ISOLATION RESISTANCE I/P-O/P:3KVAC HARMONIC CURRENT EMS IMMUNITY Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024 , EN61000-6-2 , heavy industry level, criteria A MTBF 394.8K hrs min. DIMENSION 129*98*38mm (L*W*H) 0.47Kg; 30pcs/ 15Kg/ 0.97CUFT PACKING NOTE I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B MIL-HDBK-217F (25 / 70% RH ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Derating may be needed under low input voltages. Please check the derating curve for more details. 6. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. File Name:HRP-75-SPEC 2009-10-09 HRP-75 75W Single Output with PFC Function Mechanical Specification Case No.903D series Unit:mm 31 3.5 7 122.5 9.5 1 2 3L =5 98 4 M 85.5 2- 33 8.2 3 5 1 2 SVR1 CN100 3 .5 4.5 73.5 Terminal Pin No. Assignment 129 6.5 Mating Housing Terminal JST XHP or equivalent JST SXH-001T or equivalent 3L =5 32 38 3.5 3-M 18 Assignment RCRC+ 3.5 12 max. Remote ON/OFF (CN100) : JST B-XH or equivalent Pin No. 1 2 120 28.5 Assignment DC OUTPUT -V DC OUTPUT +V 9.5 Pin No. 4 5 18.5 Assignment AC/L AC/N FG 9 Pin No. 1 2 3 77 Block Diagram ACTIVE INRUSH CURRENT LIMITING EMI FILTER I/P RECTIFIERS & PFC POWER SWITCHING O.T.P. O.L.P. RECTIFIERS & FILTER DETECTION CIRCUIT FG PFC CONTROL +V -V PWM CONTROL O.V.P. RC+ REMOTE CONTROL Derating Curve RC- Output Derating VS Input Voltage Ta = 25 100 100 90 80 80 70 LOAD(%) LOAD (%) 60 40 30 20 -20 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 60 50 40 85 100 125 135 155 264 INPUT VOLTAGE (V) 60Hz File Name:HRP-75-SPEC 2009-10-09