ML485 1.5-3.2 GHz High IP3 Mixer with Integrated LO Amp Applications • • • • • PCS / 3G Base station / Repeaters WCDMA / LTE WiMax / WiBro ISM / Fixed Wireless HPA Feedback Paths MSOP 8 Package Product Features • • • • • • • • • • Functional Block Diagram High Dynamic Range Mixer Integrated LO Driver +35 dBm Input IP3 8 dB Conversion Loss RF: 1500 – 3200 MHz LO: 1400 – 3500 MHz IF: 50 – 300 MHz +5 V Supply at 40 mA 0 dBm Drive Level 2 RoHS-compliant MSOP8 (14 mm ) Pin 1 Reference Mark LO 1 8 RF GND 2 7 GND GND 3 6 GND VCC 4 5 IF Backside Paddle - RF/DC GND General Description Pin Configuration The ML485 high linearity converter combines a passive GaAsFET mixer with an integrated LO driver in an ultrasmall lead-free/green/RoHS-compliant MSOP-8 package. The double-balanced integrated IC is able to operate across a wide 1.5 – 3.2 GHz frequency range to achieve +35 dBm Input IP3 while drawing a very low 40mA current. The ML485 can be used as an upconverter or down-converter in a low-side or high-side LO configuration. Pin No. Symbol 1 2, 3, 6, 7 4 5 8 Backside Paddle LO GND Vcc IF RF GND A LO buffer amplifier is integrated on the chip to allow for operation directly from a synthesizer requiring only 0 dBm of LO drive level. The dual-stage LO driver provides a stable input power level into the mixer to allow for consistent performance over a wide range of LO power levels. The converter requires no external baluns and supports a wide range of IF frequencies. Typical applications include frequency up/down conversion, modulation and demodulation for receivers and transmitters used in 2.5G and 3G mobile infrastructure. Due to the wide frequency range of operation, the converter can also be used for WiMAX, WiBro, ISM, LTE and fixed wireless applications Data Sheet Rev. D 07-22-14 © 2014 TriQuint Ordering Information Part No. Description ML485-G 1.5 – 3.2 GHz Mixer w/ Integrated LO Amp ML485-PCB Fully Assembled Evaluation Board Standard T/R size = 1000 pieces on a 7” reel - 1 of 9 - Disclaimer: Subject to change without notice www.triquint.com ML485 1.5-3.2 GHz High IP3 Mixer with Integrated LO Amp Absolute Maximum Ratings Recommended Operating Conditions Parameter Parameter Rating Storage Temperature DC Voltage Input IF / RF Power, CW, +25 °C LO Power −65 to +150 °C +7 V +27 dBm +10 dBm VCC TCASE 6 Tj for >10 hours MTTF Min +4.75 −40 Typ Max Units +5.0 +5.25 +85 +150 V °C °C Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions. Operation of this device outside the parameter ranges given above may cause permanent damage. Electrical Specifications Test conditions unless otherwise noted: VCC =+5 V, Temp=+25 °C, 50 Ω system. (see note 1) Parameter Min Typ Max Min Typ Max Min Typ Max Min Typ Max Units RF Frequency Range 1700 – 1800 1800 – 2200 2300 – 2400 2500 – 2700 MHz LO Frequency Range 1400 – 1750 1500 – 2150 2000 – 2350 2200 – 2650 MHz 50 – 300 50 – 300 50 – 300 50 – 300 MHz IF Freq Range SSB Conversion Loss Input IP3 (see note 2) 9.4 +28 8.7 +34 +30 8.5 9 dB +35 10 +37 +36 dBm LO Leakage RF Port −5 −2 −1 −1 dBm LO Leakage IF Port −11 −18 −25 −15 dBm RF–IF Isolation 13 16 14 11 dB RF Return Loss 13 13 15 16 dB IF Return Loss 14 14 14 14 dB LO Return Loss 10 10 12 13 dB +20 Input P1dB LO Drive Level −2 0 Parameter +20 +4 Min −2 0 Typ +19.5 +4 Max −2 +19.5 +4 −2 0 dBm +4 dBm Units Supply Voltage +5 V Supply Current Thermal Resistance (see note 3) 40 mA °C/W 84 0 Notes: 1. Specifications are shown with 0dBm LO drive and IF = 200 MHz in a down converting configuration with a low-side LO. 2. IIP3 is measured with ∆f = 1 MHz with RFin = 0 dBm / tone. 3. Thermal resistance is specified junction to case. Data Sheet Rev. D 07-22-14 © 2014 TriQuint - 2 of 9 - Disclaimer: Subject to change without notice www.triquint.com ML485 1.5-3.2 GHz High IP3 Mixer with Integrated LO Amp Performance Plots Test conditions unless otherwise noted: VCC =+5 V, Temp=+25 °C, 50 Ω system. Conversion Loss vs. RF Freq. vs. IF Freq. 11 38 IF = 51 MHz IF= 151 MHz IF= 201 MHz IF= 301 MHz 10 9 LO = 0 dBm, low-side LO, 25C 40 Input IP3 (dBm) Conversion Loss (dB) Input IP3 vs. RF Freq. vs. IF Freq. +25 C, LO = 0 dBm, low-side LO 12 8 7 36 34 32 IF = 51 MHZ IF = 151 MHz IF = 201 MHz IF = 301 MHz 30 28 6 26 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 1.5 1.7 1.9 RF Frequency (GHz) L-R Isolation vs. LO Freq. vs.Temperature 3 2 1 25 +85 °C +25 °C - 40 °C 20 15 10 0 5 1.5 1.7 1.9 2.3 2.5 2.7 2.1 LO Frequency (GHz) 2.9 3.1 3.3 1.5 1.7 R-I Isolation vs. LO Freq. vs. Temperature 1.9 2.1 2.3 2.5 2.7 LO Frequency (GHz) 2.9 3.1 3.3 3.1 3.3 Input P1dB vs. RF Frequency Referenced with LO = 0 dBm 22 +25 C, IF=201 MHz, Low-side LO at 0 dBm 22 21 Input P1dB (dBm) 19 R-I Isolation (dB) 3.3 30 +85 °C +25 °C - 40 °C 4 3.1 Referenced with LO = 0 dBm 35 L-I Isolation (dB) L-R Isolation (dB) 5 2.9 L-I Isolation vs. LO Freq. vs. Temperature Referenced with LO = 0 dBm 6 2.1 2.3 2.5 2.7 RF Frequency (GHz) 16 +85 °C +25 °C - 40 °C 13 10 20 19 18 17 7 16 4 1.5 1.7 1.9 Data Sheet Rev. D 07-22-14 © 2014 TriQuint 2.1 2.3 2.5 2.7 LO Frequency (GHz) 2.9 3.1 3.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 RF Frequency (GHz) - 3 of 9 - Disclaimer: Subject to change without notice www.triquint.com ML485 1.5-3.2 GHz High IP3 Mixer with Integrated LO Amp Performance Plots Test conditions unless otherwise noted: VCC =+5 V, Temp=+25 °C, 50 Ω system. Conversion Loss vs. RF Freq. vs. Temperature Conversion Loss vs. RF Freq. vs. LO Power LO = 0 dB, IF = 51 MHz, low-side LO 12 11 11 Conversion Loss (dB) Conversion Loss (dB) +25 C, IF = 51 MHz, low-side LO 12 10 9 8 +85 °C +25 °C - 40 °C 7 6 10 9 8 7 LO = 4 dBm LO = 0 dBm LO = -2 dBm 6 5 5 4 4 1.5 1.7 1.9 2.1 2.3 2.5 2.7 RF Frequency (GHz) 2.9 3.1 1.5 3.3 2.3 2.5 2.7 2.9 3.1 3.3 +25 C, IF = 201 MHz, low-side LO 12 11 Conversion Loss (dB) Conversion Loss (dB) 2.1 Conversion Loss vs. RF Freq. vs. LO Power LO = 0 dB, IF = 201 MHz, low-side LO 11 10 9 8 +85 °C +25 °C - 40 °C 7 6 5 10 9 8 7 LO = 4 dBm LO = 0 dBm LO = -2 dBm 6 5 4 4 1.5 1.7 1.9 2.1 2.3 2.5 2.7 RF Frequency (GHz) 2.9 3.1 3.3 1.5 Conversion Loss vs. RF Freq. vs. Temperature 1.7 1.9 2.1 2.3 2.5 2.7 RF Frequency (GHz) 2.9 3.1 3.3 Conversion Loss vs. RF Freq. vs. LO Power LO = 0 dB, IF = 301 MHz, low-side LO 12 +25 C, IF = 301 MHz, low-side LO 12 11 11 Conversion Loss (dB) Conversion Loss (dB) 1.9 RF Frequency (GHz) Conversion Loss vs. RF Freq. vs. Temperature 12 1.7 10 9 8 +85 °C +25 °C - 40 °C 7 6 5 10 9 8 7 LO = 4 dBm LO = 0 dBm LO = -2 dBm 6 5 4 4 1.5 1.7 1.9 Data Sheet Rev. D 07-22-14 © 2014 TriQuint 2.1 2.3 2.5 2.7 RF Frequency (GHz) 2.9 3.1 3.3 - 4 of 9 - 1.5 1.7 1.9 2.1 2.3 2.5 2.7 RF Frequency (GHz) 2.9 3.1 3.3 Disclaimer: Subject to change without notice www.triquint.com ML485 1.5-3.2 GHz High IP3 Mixer with Integrated LO Amp Performance Plots Test conditions unless otherwise noted: VCC =+5 V, Temp=+25 °C, 50 Ω system. Input IP3 vs. RF Freq. vs. Temperature 40 38 LO = 4 dBm LO = 0 dBm LO = -2 dBm 38 +85 °C +25 °C - 40 °C 36 +25 C, IF = 51 MHz, low-side LO 40 Input IP3 (dBm) Input IP3 (dBm) Input IP3 vs. RF Frequency vs. LO Power LO = 0 dBm, IF = 51 MHz, low-side LO 34 32 30 28 36 34 32 30 28 26 26 1.5 1.7 1.9 2.1 2.3 2.5 2.7 RF Frequency (GHz) 2.9 3.1 1.5 3.3 36 36 Input IP3 (dBm) Input IP3 (dBm) 38 34 32 +85 °C +25 °C - 40 °C 2.5 2.9 2.7 3.1 3.3 LO = 4 dBm LO = 0 dBm LO = -2 dBm 34 32 30 28 26 26 1.5 1.7 1.9 2.1 2.3 2.5 2.7 RF Frequency (GHz) 2.9 3.1 3.3 1.5 2.1 2.3 2.5 2.7 2.9 3.1 3.3 +25 C, IF = 301 MHz, low-side LO 40 LO = 4 dBm LO = 0 dBm LO = -2 dBm 38 Input IP3 (dBm) +85 °C +25 °C - 40 °C 36 1.9 Input IP3 vs. RF Frequency vs. LO Power LO = 0 dBm, IF = 301 MHz, low-side LO 38 1.7 RF Frequency (GHz) Input IP3 vs. RF Freq. vs. Temperature 40 Input IP3 (dBm) 2.3 +25 C, IF = 201 MHz, low-side LO 40 38 28 2.1 Input IP3 vs. RF Frequency vs. LO Power LO = 0 dBm, IF = 201 MHz, low-side LO 30 1.9 RF Frequency (GHz) Input IP3 vs. RF Freq. vs. Temperature 40 1.7 34 32 30 28 36 34 32 30 28 26 26 1.5 1.7 1.9 Data Sheet Rev. D 07-22-14 © 2014 TriQuint 2.1 2.3 2.5 2.7 RF Frequency (GHz) 2.9 3.1 3.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 RF Frequency (GHz) - 5 of 9 - Disclaimer: Subject to change without notice www.triquint.com ML485 1.5-3.2 GHz High IP3 Mixer with Integrated LO Amp Performance Plots Test conditions unless otherwise noted: VCC =+5 V, Temp=+25 °C, 50 Ω system. RF Return Loss vs. RF Frequency IF Return Loss vs. IF Frequency +25 C, LO = 0 dBm +25 C, LO = 0 dBm 0 -5 IF Return Loss (dB) RF Return Loss (dB) 0 -10 -15 -20 IF = 51 MHz IF = 201 MHz IF = 301 MHz -25 -30 1600 -5 -10 -15 IF = 1550 MHz IF = 1650 MHz IF = 1750 MHz -20 IF = 1850 MHz IF = 1950 MHz IF = 2050 MHz -25 1800 2000 2200 2400 2600 2800 3000 50 100 RF Frequency (MHz) 150 200 250 300 IF Frequency (MHz) LO Return Loss vs. LO Frequency +25 C, LO = 0 dBm LO Return Loss (dB) 0 -5 -10 -15 -20 -25 1600 1800 2000 2200 2400 2600 2800 3000 3200 LO Frequency (MHz) Spur Table Spur table is N × fRF – M × fLO mixer spurious products for 0 dBm input power, unless otherwise noted. RF Frequency = 1842 MHz, LO Frequency = 1642 MHz, All values in dBc relative to the IF Power Level. 0 N 0 1 2 3 4 5 M 1 2 3 4 5 2 22 35 18 85 3 0 30 23 47 35 47 81 39 51 57 70 87 80 94 72 78 81 95 93 91 93 88 88 95 95 95 92 95 95 Data Sheet Rev. D 07-22-14 © 2014 TriQuint - 6 of 9 - Disclaimer: Subject to change without notice www.triquint.com ML485 1.5-3.2 GHz High IP3 Mixer with Integrated LO Amp Down Conversion Application Circuit: ML485-PCB J4 J4 Vcc=+5V J5 J1 C1 IF Port C 1 5 6 U1 J2 7 4 U1 ML485 8 RF Input 0.01uF 3 2 1 J3 LO Port Pin Configuration and Description Pin 1 Reference Mark LO 1 8 RF GND 2 7 GND GND 3 6 GND VCC 4 5 IF Backside Paddle - RF/DC GND Pin No. Symbol 2, 3, 6, 7 GND RF/DC Ground 4 Vcc Supply voltage. An external bypass capacitor should be used near this pin. 5 IF Intermediate Frequency 8 RF Radio Frequency RF/DC Ground. Follow recommended via pattern and ensure good solder attach for best thermal and electrical performance. 1 LO Backside Paddle GND Description Local Oscillator Injection. Internally DC Blocked Evaluation Board PCB Information TriQuint PCB 1069129 Material and Stack-up 1 oz. Cu top layer 0.014" Nelco N-4000-13 1 oz. Cu inner layer 0.062" ± 0.006" Finished Board Thickness Core 1 oz. Cu inner layer 0.014" Nelco N-4000-13 1 oz. Cu bottom layer 50 ohm line dimensions: width = 0.026”, spacing = 0.025” Data Sheet Rev. D 07-22-14 © 2014 TriQuint - 7 of 9 - Disclaimer: Subject to change without notice www.triquint.com ML485 1.5-3.2 GHz High IP3 Mixer with Integrated LO Amp Package Marking and Dimensions Marking: Part Code – M42 Lot Code – YXX M42 NOTES: 1. All dimensions are in millimeters. Angles are in degrees. 2. Except where noted, this part outline conforms to JEDEC standard MO-220, Issue E (Variation VGGC) for thermally enhanced plastic very thin fine pitch quad flat no lead package (QFN). 3. Dimension and tolerance formats conform to ASME Y14.4M-1994. 4. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012 PCB Mounting Pattern 3 NOTES: 1. All dimensions are in millimeters. Angles are in degrees. 2. Use 1 oz. copper minimum for top and bottom layer metal. 3. We recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10”). 4. Ensure good package backside paddle solder attach for reliable operation and best electrical performance. Data Sheet Rev. D 07-22-14 © 2014 TriQuint - 8 of 9 - Disclaimer: Subject to change without notice www.triquint.com ML485 1.5-3.2 GHz High IP3 Mixer with Integrated LO Amp Product Compliance Information ESD Sensitivity Ratings Solderability Compatible with both lead-free (260 °C maximum reflow temperature) and tin/lead (245 °C maximum reflow temperature) soldering processes. Caution! ESD-Sensitive Device Contact plating: Electrolytic plated Au over Ni ESD Rating: Value: Test: Standard: Class 0B ≥ 125 V to < 250 V Human Body Model (HBM) ESDA/JEDEC Standard JS-001-2012 ESD Rating: Value: Test: Standard: Class C2 ≥ 500 V to < 1000 V Charged Device Model (CDM) JEDEC Standard JESD22-C101F RoHs Compliance This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). This product also has the following attributes: • Lead Free • Halogen Free (Chlorine, Bromine) • Antimony Free • TBBP-A (C15H12Br402) Free • PFOS Free • SVHC Free MSL Rating MSL Rating: Level 2 Test: 260 °C convection reflow Standard: JEDEC Standard IPC/JEDEC J-STD-020 Important Notice For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: www.triquint.com Email: [email protected] Tel: Fax: +1.503.615.9000 +1.503.615.8902 For technical questions and application information: Email: [email protected] Contact Information The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained herein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. TriQuint products are not warranted or authorized for use as critical components in medical, life-saving, or lifesustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Data Sheet Rev. D 07-22-14 © 2014 TriQuint - 9 of 9 - Disclaimer: Subject to change without notice www.triquint.com