HMC-MDB172 v00.0907 MIXERS - I/Q MIXERS / IRM - CHIP 3 GaAs MMIC I/Q MIXER 19 - 33 GHz Typical Applications Features This HMC-MDB172 is ideal for: Wide IF Bandwidth: DC - 5 GHz • Point-to-Point Radios High Image Rejection: 25 dB • VSAT High LO to RF Isolation: 35 dB • Military Radar, ECM & EW Passive: No DC Bias Required • Test & Measurement Equipment Die Size: 2.2 x 2.0 x 0.1 mm • SATCOM General Description Functional Diagram The HMC-MDB172 is a monolithic I/Q Mixer which can be used as either an image reject mixer (IRM) or a single sideband upconverter. This passive MMIC is fabricated with GaAs Heterojunction Bipolar Transistor (HBT) Shottky diode technology. For downconversion applications, an external quadrature hybrid can be used to select the desired sideband while rejecting image signals. All bond pads and the die backside are Ti/Au metallized and the Shottky devices are fully passivated for reliable operation. The HMC-MDB172 I/Q MMIC Mixer is compatible with conventional die attach methods, as well as thermocompression and thermosonic wire bonding, making it ideal for MCM and hybrid microcircuit applications. All data shown herein is measured with the chip in a 50 Ohm environment and contacted with RF probes. Electrical Specifi cations,* TA = 25 °C, IF = 3 GHz, LO = +16 dBm Parameter Min. Typ. Frequency Range, RF & LO 19 - 33 Frequency Range, IF DC - 5 Conversion Loss with External Hybrid Image Rejection 8 Max. GHz GHz 11 dB 20 25 dB 8 dBm LO to RF Isolation 30 35 dB LO to IF Isolation 18 23 dB RF to IF Isolation 19 25 dB 17 dBm 1 dB Compression (Input) IP3 (Input) *Unless otherwise indicated, all measurements are from probed die 3 - 170 Units For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-MDB172 v00.0907 GaAs MMIC I/Q MIXER 19 - 33 GHz Absolute Maximum Ratings Downconverter Conversion Loss Storage Temperature -65 °C to 150 °C Operating Temperature -55 °C to 85 °C -11 -12 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS -13 -14 -15 22 24 26 28 30 32 34 RF FREQUENCY (GHz) Note 1: Single side band measurement without 90º hybrid, and second IF port terminated. RF = 20 - 34 GHz LO = 17 - 31 GHz IF = 3 GHz PLO = +16 dBm PRF = -20 dBm For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 3 MIXERS - I/Q MIXERS / IRM - CHIP D/C CONVERSION LOSS (dB) -10 3 - 171 HMC-MDB172 v00.0907 GaAs MMIC I/Q MIXER 19 - 33 GHz Outline Drawing MIXERS - I/Q MIXERS / IRM - CHIP 3 Die Packaging Information [1] NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MM]. 2. TYPICAL BOND PAD IS .004” SQUARE. Standard Alternate WP-19 [2] [1] Refer to the “Packaging Information” section for die packaging dimensions. [2] For alternate packaging information contact Hittite Microwave Corporation. 3 - 172 3. BACKSIDE METALLIZATION: GOLD. 4. BACKSIDE METAL IS GROUND. 5. BOND PAD METALLIZATION: GOLD. 6. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS. 7. OVERALL DIE SIZE ±.002” For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-MDB172 v00.0907 GaAs MMIC I/Q MIXER 19 - 33 GHz Pad Descriptions Function Pin Description 1 RF This pad is DC coupled and matched to 50 Ohms. 2, 4 IF1, IF2 This pad is DC coupled. 3 LO This pad is DC coupled and matched to 50 Ohms. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 3 MIXERS - I/Q MIXERS / IRM - CHIP Pad Number 3 - 173 HMC-MDB172 v00.0907 GaAs MMIC I/Q MIXER 19 - 33 GHz Application Circuits MIXERS - I/Q MIXERS / IRM - CHIP 3 3 - 174 Application circuit 1 shows the mixer equivalent circuit. Application Circuit 2 depicts the mixer with a 90° hybrid used to achieve signal image rejection. All RF parameters are specified with an ideal 90° hybrid on IF output ports. Conversion loss is measured (on wafer) at IF1 and/or IF2 (Application Circuit 1) with the second IF port terminated into 50 ohms. Three dB is then added to compensate for an ideal hybrid. The IP3 is stated as an input IP3 number and is obtained via a two-tone measurement. Application Circuit 1 Application Circuit 2 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-MDB172 v00.0907 GaAs MMIC I/Q MIXER 19 - 33 GHz Assembly Diagram MIXERS - I/Q MIXERS / IRM - CHIP 3 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 3 - 175 HMC-MDB172 v00.0907 GaAs MMIC I/Q MIXER 19 - 33 GHz Mounting & Bonding Techniques for Millimeterwave GaAs MMICs The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). MIXERS - I/Q MIXERS / IRM - CHIP 3 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). 0.102mm (0.004”) Thick GaAs MMIC Wire Bond 0.076mm (0.003”) RF Ground Plane Microstrip substrates should be placed as close to the die as possible in order to minimize bond wire length. Typical die-to-substrate spacing is 0.076mm to 0.152 mm (3 to 6 mils). 0.127mm (0.005”) Thick Alumina Thin Film Substrate Figure 1. Handling Precautions Follow these precautions to avoid permanent damage. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: strikes. 0.102mm (0.004”) Thick GaAs MMIC Wire Bond 0.076mm (0.003”) RF Ground Plane Follow ESD precautions to protect against ESD Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pick-up. 0.150mm (0.005”) Thick Moly Tab 0.254mm (0.010”) Thick Alumina Thin Film Substrate Figure 2. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. Wire Bonding RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded with a force of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve reliable bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm). 3 - 176 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC-MDB172 v00.0907 GaAs MMIC I/Q MIXER 19 - 33 GHz Notes: MIXERS - I/Q MIXERS / IRM - CHIP 3 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 3 - 177