BELLING BL9310 1.5 mhz, 1a synchronous buck converter Datasheet

BL9310
1.5 MHz, 1A Synchronous Buck Converter
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
High Efficiency: Up to 96%
1.5MHz Constant Switching Frequency
Current Mode Operation for Excellent
Line and Load Transient Response
No Schottky Diode Required
2.5V to 5.5V Input Voltage Range
1.0V,1.2V,1.5V,1.8V,2.5V and 3.3V
Fixed/Adjustable Output Voltage
100% Duty Cycle in Dropout Mode
Low Quiescent Current: 200µA
Over temperature Protection
Short Circuit Protection
Shutdown Quiescent Current < 1µA
Space Saving 5-Pin Thin SOT23 Package
APPLICATIONS
•
•
•
•
•
•
Cellular and Smart Phones
Wireless Handsets and DSL Modems
Microprocessors and DSP Core Supplies
PDAs
Digital Still and Video Cameras
MP3/MP4/MP5 Players
ORDERING INFORMATION
BL9310 –XX X XXX
•
•
Portable Instruments
GPS Receivers
DESCRIPTION
The BL9310 is a constant frequency, 1.5MHz,
slope compensated current mode PWM stepdown converter working under an input
voltage range of 2.5V to 5.5V. This feature
makes the BL9310 suitable for single cell Liion battery-powered applications. The internal
synchronous rectifier is desired to increase
efficiency without an external Schottky diode.
100% duty cycle capability extends battery
life in portable devices, while the quiescent
current is 200µA at no load, and drops to <
1µA in shutdown. Pulse Skipping Mode
operation increases efficiency at light loads,
further extending battery life. The BL9310 is
offered in a low profile (1mm) 5-pin, thin
SOT23 package, and is available in an
adjustable version and fixed output versions
of 1.0V, 1.2V, 1.5V , 1.8V, 2.5V and 3.3V.
TYPICAL APPLICATION
:
Package
TRN: TSOT23-5
RN: SOT23-5
Features:
P: Standard (default,
lead free)
C: Customized
:
Output Voltage
10: 1.0V
12: 1.2V
15: 1.5V
18: 1.8V
25: 2.5V
33: 3.3V
AD: Adjustable
PPMIC BU
BL9310 Rev 1.1
1/2011
Figure 1. BL9310-ADJ Typical Application Circuit
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
1
BL9310
1.5 MHz, 1A Synchronous Buck Converter
Absolute Maximum Rating (Note 1)
Input Supply Voltage…………………-0.3V to +6V
RUN, VFB Voltages……………………-0.3V to +VIN
SW Voltages……………………-0.3V to (VIN+0.3V)
P-Channel Switch Source Current (DC) ……1.1A
N-Channel Switch Sink Current (DC) ……1.1A
Peak SW Sink and Source Current……………1.5A
Operating Temperature Range……-40°C to +85°C
(Note2)
Junction Temperature
………………+125°C
Storage Temperature Range………-65°C to +150°C
Lead Temperature (Soldering, 10s) ………+300°C
Package Information
Adjustable Output Version
RUN
5
VFB
RUN
3
GND 2
4
Top Mark
(Note3)
IJYW
SW
VIN
Temp Range
-40°C to +85°C
Thermal Resistance (Note 4)
Package
TSOT23-5
SOT23-5
ӨJA
220°C/W
250°C/W
1
Part Number
BL9310-1.0
BL9310-1.2
BL9310-1.5
BL9310-1.8
BL9310-2.5
BL9310-3.3
5
VOUT
4
VIN
MARKING
Part Number
BL9310-Adj
SOT23-5
TOP VIEW
MARKING
SW
SOT23-5
TOP VIEW
1
GND 2
Fixed Output Versions
3
Top Mark
IAYW
IBYW
ICYW
IDYW
IEYW
IFYW
Temp Range
-40°C to +85°C
ӨJC
110°C/W
130°C/W
Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired.
Note 2: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formula:
TJ = TA + (PD) x (220°C/W).
Note 3: I: Product Code Y: Year of Manufacturing W: Week of Manufacturing
Note 4: Thermal Resistance is specified with approximately 1 square of 1 oz copper.
PPMIC BU
BL9310 Rev 1.1
1/2011
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
2
BL9310
1.5 MHz, 1A Synchronous Buck Converter
Pin Description
PIN
NAME
1
RUN
2
GND
3
SW
4
VIN
5
VFB/VOUT
FUNCTION
Regulator Enable Control Input. Drive RUN above 1.5V to turn on the part.
Drive RUN below 0.3V to turn it off. In shutdown, all functions are disabled
drawing <1µA supply current. Do not leave RUN floating.
Ground
Power Switch Output. It is the switch node connection to external inductor. This
pin connects to the drains of the internal P-Channel and N-Channel MOSFET
switches.
Supply Input Pin. Must be closely decoupled to GND, Pin 2, with a 2.2µF or
greater ceramic capacitor.
VFB (BL9310-Adj): Feedback Input Pin. Connect FB to the center point of the
external resistor divider. The regulated voltage on this pin is 0.6V.
VOUT (BL9310-1.2/BL9310-1.5/BL9310-1.8): Output Voltage Feedback Pin. An
internal resistive divider divides the output voltage down for comparison to the
internal reference voltage.
Block Diagram
PPMIC BU
BL9310 Rev 1.1
1/2011
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
3
BL9310
1.5 MHz, 1A Synchronous Buck Converter
Electrical Characteristics
(Note 5)
(VIN =VRUN= 3.6V, TA = 25°C, unless otherwise noted.)
Parameter
Conditions
Input Voltage Range
Input DC Supply Current
Active Mode
VFB=0.5V or VOUT=90%
Shutdown Mode
VFB=0V, VIN=4.2V
TA = +25°C
Regulated Feedback
TA= 0°C ≤ TA ≤ 85°C
Voltage
TA= -40°C ≤ TA ≤ 85°C
VFB Input Bias Current
VFB = 0.65V
Reference Voltage Line
Regulation
VIN = 2.5V to 5.5V
Regulated Output Voltage
Output Overvoltage
Lockout
Output Voltage Line
Regulation
Output Voltage Load
Regulation
TYP
MAX
Unit
5.5
V
300
1.0
0.6120
0.6135
0.6150
µA
µA
V
V
V
±30
nA
0.04
0.4
%/V
2.5
0.5880
0.5865
0.5850
200
0.1
0.6000
0.6000
0.6000
BL9310-1.2, -40°C ≤ TA ≤ 85°C
BL9310-1.8, -40°C ≤ TA ≤ 85°C
∆VOVL = VOVL – VFB, Adjustable Version
1.164
1.746
20
1.200
1.800
50
1.236
1.854
80
V
V
mV
∆VOVL = VOVL – VOUT, Fixed Version
2.5
7.8
13
%
0.04
0.40
%
VIN = 2.5V to 5.5V
Oscillator Frequency
RDS(ON) of P-CH MOSFET
VIN=3V, VFB=0.5V or VOUT=90%
Duty Cycle <35%
VFB=0.6V or VOUT=100%
ISW = 300mA
RDS(ON) of N-CH MOSFET
Peak Inductor Current
MIN
1.2
0.5
%
1.3
A
1.5
0.40
1.8
0.50
MHz
Ω
ISW = -300mA
0.35
0.45
Ω
SW Leakage Current
VRUN = 0V, VSW = 0V or 5V, VIN = 5V
±0.01
±1
µA
RUN Threshold
RUN Leakage Current
-40°C ≤ TA ≤ 85°C
1.1
±0.01
1.30
±1
V
µA
0.3
Note 5: 100% production test at +25°C. Specifications over the temperature range are guaranteed by design and
characterization.
PPMIC BU
BL9310 Rev 1.1
1/2011
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
4
BL9310
1.5 MHz, 1A Synchronous Buck Converter
Typical Performance Characteristics
(Test Figure 1 above unless otherwise specified)
Output Voltage vs. Load Current
Efficiency vs. Output Current
2.2
VIN=3.6V
TA=25°C
2.1
90
80
Efficiency (%)
Output Voltage(V)
2.0
1.9
1.8
1.7
70
60
50
Vin=2.7V
Vin=3.6V
Vin=4.2V
1.6
40
1.5
30
1.4
20
1.3
0
200
400
600
800
1000
10
1200
Load Current(mA)
1000
Output Voltage vs. Input Voltage
Reference Voltage vs. Temperature
0.606
1.820
VIN=3.6V
ILOAD=10mA
ILOAD=100mA
ILOAD=600mA
1.815
0.605
1.810
VOUT(V)
Reference Voltage(V)
100
Output Current (mA)
0.604
1.805
1.800
1.795
0.603
1.790
1.785
0.602
-50
-25
0
25
50
75
100
125
1.780
2.7
3.0
3.3
3.6
3.9
4.2
4.5
4.8
5.1
Temperature(°C)
VIN(V)
Supply Current vs. Supply Voltage
Start_up from Shutdown
5.4
5.7
245
VOUT=1.8V
ILOAD=0A
TA=25°C
Dynamic Supply Current(uA)
240
235
230
225
220
215
210
205
200
195
2
3
4
5
6
Supply Voltage(V)
PPMIC BU
BL9310 Rev 1.1
1/2011
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
5
BL9310
1.5 MHz, 1A Synchronous Buck Converter
Load Step
Load Step
Load Step
Load Step
Pulse Skipping Mode
PPMIC BU
BL9310 Rev 1.1
1/2011
Output Short
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
6
BL9310
1.5 MHz, 1A Synchronous Buck Converter
Operation
The BL9310 uses a constant frequency,
current mode step-down architecture. Both
the main switch (P-channel MOSFET) and
the
synchronous
rectifier
(N-channel
MOSFET) are integrated internally. This
Step-Down DC-DC Converter can supply
600mA output current over a wide input
voltage range from 2.5V to 5.5V. The over
voltage comparator OVDET guards against
transient overshoots >7.8% by turning the
main switch off and keeping it off until the
fault is removed.
value of the output voltage, the BL9310 will
keep the main switch on for more than one
switching cycle and increases the duty cycle
(Note 5) until it reaches 100%. The output
voltage then is the input voltage minus the
voltage drop across the main switch and the
inductor. At low input supply voltage, the
RDS(ON) of the P-Channel MOSFET increases,
and the efficiency of the converter decreases.
Caution must be exercised to ensure the heat
dissipated not to exceed the maximum
junction temperature of the IC.
Note 6: The duty cycle D of a step-down converter is
defined as:
D = TON × f OSC × 100% ≈
Current Mode PWM Control
Slope compensated current mode PWM
control provides stable switching and cycleby-cycle current limit for excellent load and
line responses. During normal operation, the
internal main switch is turned on for a certain
time to ramp the inductor current at each
rising edge of the internal oscillator, and
turned off when the peak inductor current
reaches the controlled value. When the main
switch is off, the synchronous rectifier will be
turned on immediately and stay on until either
the inductor current starts to reverse, as
indicated by the current reversal comparator,
IRCMP, or the beginning of the next clock cycle.
VOUT
× 100%
VIN
where TON is the main switch on time, and fOSC
is the oscillator frequency (1.5MHz).
Short Circuit Protection
The BL9310 has short circuit protection.
When output is shorted to ground, the
oscillator frequency is reduced to prevent the
inductor current from increasing beyond the
PFET current limit. The PFET current limit is
also reduced to lower the short circuit current.
The frequency and current limit will return to
the normal values once the short circuit
condition is removed and the feedback
voltage reaches 0.6V.
Pulse Skipping Mode Operation
Maximum Load Current
At very light loads, the BL9310 will
automatically enter Pulse Skipping Mode to
increase efficiency, further extending battery
life. In this mode, the control loop skips PWM
pulses while maintaining output in regulation,
and the switching frequency depends on the
load condition. This is a kind of PFM mode
operation.
The BL9310 will operate with input supply
voltage as low as 2.5V, however the
maximum load current decreases at lower
input voltage due to large IR drop on the
main switch and synchronous rectifier.
Dropout Operation
When the input voltage decreases toward the
PPMIC BU
BL9310 Rev 1.1
1/2011
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
7
BL9310
1.5 MHz, 1A Synchronous Buck Converter
Application Information
Figure 2 below shows the basic application
circuit with BL9310 fixed output versions.
Figure 2. Basic Application Circuit
with fixed output versions
Input Capacitor Selection
Setting the Output Voltage
Figure 1 above shows the basic application
circuit with BL9310 adjustable output version.
The external resistor sets the output voltage
according to the following equation:
R2
)
R1
Table 1—Resistor Selection vs.
Output Voltage Setting
VOUT
R1
R2
1.0V
180 kΩ(1%)
120 kΩ(1%)
1.2V
180 kΩ(1%)
180 kΩ(1%)
1.5V
180 kΩ(1%)
270 kΩ(1%)
1.8V
180 kΩ(1%)
360 kΩ(1%)
2.5V
158 kΩ(1%)
499 kΩ(1%)
3.3V
180 kΩ(1%)
810 kΩ(1%)
VOUT = 0.6V × (1 +
Inductor Selection
The output inductor is selected to limit the
ripple current to some predetermined value,
typically 20%~40% of the full load current at
the maximum input voltage. In continuous
mode, the ripple current is determined by:
∆I L =
PPMIC BU
BL9310 Rev 1.1
1/2011
V
1
VOUT (1 − OUT )
f ×L
VIN
A reasonable starting point for setting ripple
current is ∆IL=240mA (40% of 600mA). For
output voltages above 2.0V, when efficiency
at light load condition is important, the
minimum recommended inductor is 2.2µH.
For
optimum
voltage-positioning
load
transients, choose an inductor with DC series
resistance below 150mΩ. For higher
efficiency at heavy loads (above 200mA), or
minimal load regulation (but some transient
overshoot), the resistance should be kept
below 100mΩ. The DC current rating of the
inductor should be at least equal to the
maximum load current plus half the ripple
current to prevent core saturation. Thus, a
720mA rated inductor should be enough for
most applications (600mA+120mA).
The input capacitor reduces the surge current
drawn from the input and switching noise
from the device. The input capacitor
impedance at the switching frequency shall
be less than input source impedance to
prevent high frequency switching current
passing to the input. In continuous mode, the
source current of the main switch is a square
wave of duty cycle VOUT/VIN. To prevent large
voltage transients, a low ESR input capacitor
sized for the maximum RMS current must be
used. The maximum RMS capacitor current is
given by:
I RMS ≈ I OMAX
[VOUT (VIN − VOUT )]0.5
VIN
This formula has a maximum at VIN =2VOUT,
where IRMS = IOUT/2. This simple worst-case
condition is commonly used for design
because even significant deviations do not
offer much relief. Ceramic capacitors with
X5R or X7R dielectrics are recommended
due to their low ESR and high ripple current.
Output Capacitor Selection
The output capacitor is required to keep the
output voltage ripple small and to ensure
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
8
BL9310
1.5 MHz, 1A Synchronous Buck Converter
regulation loop stability. The output capacitor
must have low impedance at the switching
frequency. Ceramic capacitors with X5R or
X7R dielectrics are recommended due to
their low ESR and high ripple current. The
output ripple ∆VOUT is determined by:

VOUT×(VIN −VOUT) 
1

× ESR+
VIN × fOSC× L 
8× fOSC×C2 
Efficiency Considerations
∆VOUT ≤
Layout Considerations
When laying out the printed circuit board, the
following checklist should be used to ensure
proper operation of the BL9310. These items
are also illustrated graphically in Figures 5
and 6. Check the following in your layout:
Figure 3. BL9310-ADJ Layout Circuit
1. The power traces, consisting of the GND
trace, the SW trace and the VIN trace
should be kept short, direct and wide.
2. Does the VFB pin connect directly to the
feedback resistors? The resistive divider
R1/R2 must be connected between the (+)
plate of Cout and ground.
3. Does the (+) plate of CIN connect to VIN as
closely as possible? This capacitor
provides the AC current to the internal
power MOSFETS.
4. Keep the switching node, SW, away from
the sensitive VFB node.
5. Keep the (-) plates of CIN and COUT as
close as possible.
Figure 4. BL9310-1.8 Layout Circuit
BL9310BL9310-ADJ
BL9310BL9310-18
Figure 5. BL9310-ADJ Suggested Layout
PPMIC BU
BL9310 Rev 1.1
1/2011
Figure 6. BL9310-1.8 Suggested Layout
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
9
BL9310
1.5 MHz, 1A Synchronous Buck Converter
Package Description
Symbol
A
A1
B
b
C
D
e
H
L
Dimensions In Millimeters
Min
0.889
0.000
1.397
0.356
2.591
2.692
0.838
0.080
0.300
Dimensions In Inches
Max
1.295
0.152
1.803
0.559
2.997
3.099
1.041
0.254
0.610
Min
0.035
0.000
0.055
0.014
0.102
0.106
0.033
0.003
0.012
Max
0.051
0.006
0.071
0.022
0.118
0.122
0.041
0.010
0.024
SOT-23-5 Surface Mount Package
PPMIC BU
BL9310 Rev 1.1
1/2011
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
10
BL9310
1.5 MHz, 1A Synchronous Buck Converter
TSOT-23-5 Surface Mount Package
PPMIC BU
BL9310 Rev 1.1
1/2011
www.belling.com.cn
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
©2011 Belling All Rights Reserved
11
Similar pages