DATASHEET ISL6566 FN9178 Rev 4.00 Mar 9, 2006 Three-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications The ISL6566 three-phase PWM control IC provides a precision voltage regulation system for advanced microprocessors. The integration of power MOSFET drivers into the controller IC marks a departure from the separate PWM controller and driver configuration of previous multiphase product families. By reducing the number of external parts, this integration is optimized for a cost and space saving power management solution. Features Outstanding features of this controller IC include programmable VID codes compatible with Intel VRM9, VRM10, as well as AMD Hammer microprocessors. A unity gain, differential amplifier is provided for remote voltage sensing, compensating for any potential difference between remote and local grounds. The output voltage can also be positively or negatively offset through the use of a single external resistor. • Precision Channel Current Sharing - Uses Loss-Less rDS(ON) Current Sampling • Accurate Load Line Programming - Uses Loss-Less Inductor DCR Current Sampling • Variable Gate Drive Bias: 5V to 12V • Microprocessor Voltage Identification Inputs - Up to a 6-Bit DAC - Selectable between Intel’s VRM9, VRM10, or AMD Hammer DAC Codes - Dynamic VID Technology • Overcurrent Protection • Multi-tiered Overvoltage Protection • Digital Soft-Start • Selectable Operation Frequency up to 1.5MHz Per Phase • Pb-Free Plus Anneal Available (RoHS Compliant) Pinout VID4 ENLL FS PGOOD LGATE1 PVCC1 ISEN1 UGATE1 ISL6566 (QFN) TOP VIEW VID3 Protection features of this controller IC include a set of sophisticated overvoltage, undervoltage, and overcurrent protection. Overvoltage results in the converter turning the lower MOSFETs ON to clamp the rising output voltage and protect the microprocessor. The overcurrent protection level is set through a single external resistor. Furthermore, the ISL6566 includes protection against an open circuit on the remote sensing inputs. Combined, these features provide advanced protection for the microprocessor and power system. • Precision Core Voltage Regulation - Differential Remote Voltage Sensing - 0.5% System Accuracy Over Temperature - Adjustable Reference-Voltage Offset VID2 A unique feature of the ISL6566 is the combined use of both DCR and rDS(ON) current sensing. Load line voltage positioning (droop) and overcurrent protection are accomplished through continuous inductor DCR current sensing, while rDS(ON) current sensing is used for accurate channel-current balance. Using both methods of current sampling utilizes the best advantages of each technique. • Integrated Multi-Phase Power Conversion - 1, 2, or 3-Phase Operation 40 39 38 37 36 35 34 33 32 31 VID1 1 30 BOOT1 VID0 2 29 PHASE1 VID12.5 3 28 PHASE2 VRM10 4 27 UGATE2 REF 5 OFS 6 VCC 7 24 PVCC2 COMP 8 23 LGATE2 FB 9 22 PHASE3 26 BOOT2 41 GND 25 ISEN2 VDIFF 10 FN9178 Rev 4.00 Mar 9, 2006 13 14 15 16 17 18 VSEN OCSET ICOMP ISUM IREF LGATE3 PVCC3 19 20 UGATE3 12 ISEN3 11 RGND 21 BOOT3 Page 1 of 30 ISL6566 Ordering Information PART NUMBER PART MARKING TEMP. (°C) PACKAGE PKG. DWG. # ISL6566CRR5184 ISL6566CR 0 to 70 40 Ld 6x6 QFN L40.6x6 ISL6566CR-TR5184 ISL6566CR 0 to 70 40 Ld 6x6 QFN Tape and Reel L40.6x6 ISL6566CRZR5184 (Note) ISL6566CRZ 0 to 70 40 Ld 6x6 QFN (Pb-free) L40.6x6 ISL6566CRZ-TR5184 (Note) ISL6566CRZ 0 to 70 40 Ld 6x6 QFN (Pb-free) Tape and Reel L40.6x6 ISL6566CRZAR5184 (Note) ISL6566CRZ 0 to 70 40 Ld 6x6 QFN (Pb-free) L40.6x6 ISL6566CRZA-TR5184 (Note) ISL6566CRZ 0 to 70 40 Ld 6x6 QFN (Pb-free) Tape and Reel L40.6x6 ISL6566IR ISL6566IR -40 to 85 40 Ld 6x6 QFN L40.6x6 ISL6566IR-T ISL6566IR -40 to 85 40 Ld 6x6 QFN Tape and Reel L40.6x6 ISL6566IRZ (Note) ISL6566IRZ -40 to 85 40 Ld 6x6 QFN (Pb-free) L40.6x6 ISL6566IRZ-T (Note) ISL6566IRZ -40 to 85 40 Ld 6x6 QFN (Pb-free) Tape and Reel L40.6x6 ISL6566IRZA (Note) ISL6566IRZ -40 to 85 40 Ld 6x6 QFN (Pb-free) L40.6x6 ISL6566IRZA-T (Note) ISL6566IRZ -40 to 85 40 Ld 6x6 QFN (Pb-free) L40.6x6 NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN9178 Rev 4.00 Mar 9, 2006 Page 2 of 30 ISL6566 Block Diagram ICOMP ENLL PGOOD OCSET 100A ISEN AMP 0.66V ISUM POWER-ON RESET OC IREF VCC PVCC1 RGND VSEN BOOT1 +1V UGATE1 SOFT-START AND x1 x1 GATE CONTROL LOGIC FAULT LOGIC SHOOTTHROUGH PROTECTION PHASE1 VDIFF LGATE1 UVP 0.2V FS OVP PVCC2 CLOCK AND SAWTOOTH GENERATOR OVP VOVP BOOT2 UGATE2 PWM1 GATE CONTROL LOGIC +150mV x 0.82 SHOOTTHROUGH PROTECTION PHASE2 PWM2 LGATE2 VID4 VID3 VID2 VID1 VID0 DYNAMIC VID D/A PWM3 CHANNEL DETECT PVCC3 VID12.5 VRM10 BOOT3 REF CHANNEL CURRENT BALANCE E/A FB 1 N COMP OFS UGATE3 GATE CONTROL LOGIC SHOOTTHROUGH PROTECTION OFFSET PHASE3 LGATE3 CHANNEL CURRENT SENSE ISEN1 FN9178 Rev 4.00 Mar 9, 2006 ISEN2 ISEN3 GND Page 3 of 30 ISL6566 Typical Application - ISL6566 +12V VDIFF FB COMP VSEN PVCC1 BOOT1 RGND UGATE1 +5V PHASE1 VCC ISEN1 LGATE1 OFS +12V FS PVCC2 REF VID4 ISL6566 BOOT2 UGATE2 VID3 PHASE2 VID2 ISEN2 VID1 LOAD LGATE2 VID0 VID12.5 VRM10 +12V PGOOD +12V PVCC3 GND BOOT3 UGATE3 PHASE3 ENLL ISEN3 IREF OCSET ICOMP FN9178 Rev 4.00 Mar 9, 2006 ISUM LGATE3 Page 4 of 30 ISL6566 Typical Application - ISL6566 with NTC Thermal Compensation +12V VDIFF FB COMP VSEN PVCC1 BOOT1 RGND UGATE1 +5V PHASE1 VCC ISEN1 LGATE1 OFS +12V FS PVCC2 REF VID4 ISL6566 BOOT2 UGATE2 VID3 PHASE2 VID2 ISEN2 VID1 LOAD LGATE2 VID0 VID12.5 VRM10 PGOOD +12V +12V PVCC3 GND BOOT3 PLACE IN CLOSE PROXIMITY UGATE3 ENLL IREF OCSET ICOMP FN9178 Rev 4.00 Mar 9, 2006 PHASE3 ISEN3 NTC LGATE3 ISUM Page 5 of 30 ISL6566 Absolute Maximum Ratings Thermal Information Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6V Supply Voltage, PVCC . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +15V Absolute Boot Voltage, VBOOT . . . . . . . . GND - 0.3V to GND + 36V Phase Voltage, VPHASE . . . . . . . . GND - 0.3V to 15V (PVCC = 12) GND - 8V (<400ns, 20µJ) to 24V (<200ns, VBOOT-PHASE = 12V) Upper Gate Voltage, VUGATE . . . . VPHASE - 0.3V to VBOOT + 0.3V VPHASE - 3.5V (<100ns Pulse Width, 2µJ) to VBOOT + 0.3V Lower Gate Voltage, VLGATE. . . . . . . . GND - 0.3V to PVCC + 0.3V GND - 5V (<100ns Pulse Width, 2µJ) to PVCC+ 0.3V Input, Output, or I/O Voltage . . . . . . . . . GND - 0.3V to VCC + 0.3V ESD Classification . . . . . . . . . . . . . . . . . . . . . . . Class I JEDEC STD Thermal Resistance JA (°C/W) JC (°C/W) QFN Package (Notes 1, 2) . . . . . . . . . . 32 3.5 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C Recommended Operating Conditions VCC Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V 5% PVCC Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . +5V to 12V 5% Ambient Temperature (ISL6566CR, ISL6566CRZ) . . . . 0°C to 70°C Ambient Temperature (ISL6566IR, ISL6566IRZ) . . . . .-40°C to 85°C CAUTION: Stress above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. NOTES: 1. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 2. For JC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications Recommended Operating Conditions, Unless Otherwise Specified. PARAMETER TEST CONDITIONS MIN TYP MAX UNITS BIAS SUPPLY AND INTERNAL OSCILLATOR Input Bias Supply Current IVCC; ENLL = high - 15 20 mA Gate Drive Bias Current IPVCC; ENLL = high - 0.8 - mA VCC POR (Power-On Reset) Threshold VCC Rising 4.25 4.38 4.50 V VCC Falling 3.75 3.88 4.00 V PVCC Rising 4.25 4.38 4.50 V PVCC Falling 3.60 3.88 4.00 V - 1.50 - V - 66.6 - % 225 250 275 kHz ENLL Rising Threshold - 0.66 - V ENLL Hysteresis - 100 - mV 0.2 0.3 0.4 V System Accuracy (VID = 1.0V - 1.850V) -0.5 - 0.5 % System Accuracy (VID = 0.8V - 1.0V) -0.8 - 0.8 % DAC Input Low Voltage (VR9, VR10) - - 0.4 V DAC Input High Voltage (VR9, VR10) 0.8 - - V DAC Input Low Voltage (AMD) - - 0.6 V DAC Input High Voltage (AMD) 1.0 - - V PVCC POR (Power-On Reset) Threshold Oscillator Ramp Amplitude (Note 3) VPP Maximum Duty Cycle (Note 3) Oscillator Frequency, FSW RT = 100k (1%) CONTROL THRESHOLDS COMP Shutdown Threshold COMP Falling REFERENCE AND DAC OFS Sink Current Accuracy (Negative Offset) ROFS = 30kfrom OFS to VCC 47.5 50.0 52.5 A OFS Source Current Accuracy (Positive Offset) ROFS = 10kfrom OFS to GND 47.5 50.0 52.5 A FN9178 Rev 4.00 Mar 9, 2006 Page 6 of 30 ISL6566 Electrical Specifications Recommended Operating Conditions, Unless Otherwise Specified. (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS ERROR AMPLIFIER DC Gain (Note 3) RL = 10K to ground - 96 - dB Gain-Bandwidth Product (Note 3) CL = 100pF, RL = 10K to ground - 20 - MHz Slew Rate (Note 3) CL = 100pF, Load = 400A - 8 - V/s Maximum Output Voltage Load = 1mA 3.90 4.20 - V Minimum Output Voltage Load = -1mA - 0.85 1.0 V 93 100 107 A -5 0 5 mV -5 0 5 mV OVERCURRENT PROTECTION OCSET trip current OCSET Accuracy OCSET and ISUM Difference ICOMP Offset PROTECTION Undervoltage Threshold VSEN falling 80 82 84 %VID Undervoltage Hysteresis VSEN Rising - 3 - %VID Overvoltage Threshold while IC Disabled VOVP, VRM9.0 Configuration 1.92 1.97 2.02 V VOVP, Hammer and VRM10.0 Configurations 1.62 1.67 1.72 V Overvoltage Threshold VSEN Rising VID + 125mV VID + 150mV VID + 175mV V Overvoltage Hysteresis VSEN Falling - 50 - mV Open Sense-Line Protection Threshold IREF Rising and Falling VDIFF + 0.9V VDIFF + 1V VDIFF + 1.1V V SWITCHING TIME (Note 3) UGATE Rise Time tRUGATE; VPVCC = 12V, 3nF Load, 10% to 90% - 26 - ns LGATE Rise Time tRLGATE; VPVCC = 12V, 3nF Load, 10% to 90% - 18 - ns UGATE Fall Time tFUGATE; VPVCC = 12V, 3nF Load, 90% to 10% - 18 - ns LGATE Fall Time tFLGATE; VPVCC = 12V, 3nF Load, 90% to 10% - 12 - ns UGATE Turn-On Non-overlap tPDHUGATE; VPVCC = 12V, 3nF Load, Adaptive - 10 - ns LGATE Turn-On Non-overlap tPDHLGATE; VPVCC = 12V, 3nF Load, Adaptive - 10 - ns GATE DRIVE RESISTANCE (Note 3) Upper Drive Source Resistance VPVCC = 12V, 15mA Source Current 1.25 2.0 3.0 Upper Drive Sink Resistance VPVCC = 12V, 15mA Sink Current 0.9 1.65 3.0 Lower Drive Source Resistance VPVCC = 12V, 15mA Source Current 0.85 1.25 2.2 Lower Drive Sink Resistance VPVCC = 12V, 15mA Sink Current 0.60 0.80 1.35 Thermal Shutdown Setpoint (Note 3) - 160 - °C Thermal Recovery Setpoint (Note 3) - 100 - °C OVER TEMPERATURE SHUTDOWN NOTE: 3. Parameter magnitude guaranteed by design. Not 100% tested. FN9178 Rev 4.00 Mar 9, 2006 Page 7 of 30 ISL6566 Timing Diagram tPDHUGATE tRUGATE tFUGATE UGATE LGATE tFLGATE tRLGATE tPDHLGATE Simplified Power System Diagram +12VIN +5VIN Q1 CHANNEL1 Q2 VID 5-6 DAC Q3 VOUT CHANNEL2 Q4 ISL6566 Q5 CHANNEL3 Q6 Functional Pin Description VCC VCC is the bias supply for the ICs small-signal circuitry. Connect this pin to a +5V supply and locally decouple using a quality 1.0F ceramic capacitor. PVCC1, PVCC2, PVCC3 These pins are the power supply pins for the corresponding channel MOSFET drive, and can be connected to any voltage from +5V to +12V, depending on the desired MOSFET gate drive level. The number of active channels is determined by the state of PVCC2 and PVCC3. Leave PVCC3 unconnected or grounded for 2-phase operation. For 1-phase operation leave both PVCC3 and PVCC2 unconnected or grounded. FN9178 Rev 4.00 Mar 9, 2006 GND GND is the bias and reference ground for the IC. ENLL This pin is a threshold-sensitive (approximately 0.66V) enable input for the controller. Held low, this pin disables controller operation. Pulled high, the pin enables the controller for operation. ENLL has a internal 1.0A pull-up to 5V. FS A resistor, placed from FS to ground, will set the switching frequency. Refer to Equation 34 for proper resistor calculation. Page 8 of 30 ISL6566 VID4, VID3, VID2, VID1, VID0, and VID12.5 These are the inputs for the internal DAC that provides the reference voltage for output regulation. These pins respond to TTL logic thresholds. The ISL6566 decodes the VID inputs to establish the output voltage; see VID Tables for correspondence between DAC codes and output voltage settings. These pins are internally pulled high, to approximately 1.2V, by 40A (typically) internal current sources; the internal pull-up current decreases to 0 as the VID voltage approaches the internal pull-up voltage. All VID pins are compatible with external pull-up voltages not exceeding the IC’s bias voltage (VCC). VRM10 This pin selects VRM10.0 DAC compliance when pulled high or open. If VRM10 is grounded, VID12.5 selects the compliance standard for the internal DAC: pulled to ground, it encodes the DAC with AMD Hammer VID codes, while left open or pulled high, it encodes the DAC with Intel VRM9.0 codes. VSEN and RGND VSEN and RGND are inputs to the precision differential remote-sense amplifier and should be connected to the sense pins of the remote load. ICOMP, ISUM, and IREF ISUM, IREF, and ICOMP are the DCR current sense amplifier’s negative input, positive input, and output respectively. For accurate DCR current sensing, connect a resistor from each channel’s phase node to ISUM and connect IREF to the summing point of the output inductors, roughly Vout. A parallel R-C feedback circuit connected between ISUM and ICOMP will then create a voltage from IREF to ICOMP proportional to the voltage drop across the inductor DCR. This voltage is referred to as the droop voltage and is added to the differential remote-sense amplifier output. Note: An optional 0.01F ceramic capacitor can be placed from the IREF pin to the ISUM pin, or from the IREF pin to GND to help reduce any noise affects that may occur due to layout. VDIFF VDIFF is the output of the differential remote-sense amplifier. The voltage on this pin is equal to the difference between VSEN and RGND added to the difference between IREF and ICOMP. VDIFF therefore represents the output voltage plus the droop voltage. FB and COMP These pins are the internal error amplifier inverting input and output respectively. FB, VDIFF, and COMP are tied together through external R-C networks to compensate the regulator. REF to smooth the voltage transition during Dynamic VID operations. OFS The OFS pin provides a means to program a dc current for generating an offset voltage across the resistor between FB and VDIFF. The offset current is generated via an external resistor and precision internal voltage references. The polarity of the offset is selected by connecting the resistor to GND or VCC. For no offset, the OFS pin should be left unconnected. OCSET This is the overcurrent set pin. Placing a resistor from OCSET to ICOMP allows a 100A current to flow out this pin, producing a voltage reference. Internal circuitry compares the voltage at OCSET to the voltage at ISUM, and if ISUM ever exceeds OCSET, the overcurrent protection activates. ISEN1, ISEN2 and ISEN3 These pins are used for balancing the channel currents by sensing the current through each channel’s lower MOSFET when it is conducting. Connect a resistor between the ISEN1, ISEN2, and ISEN3 pins and their respective phase node. This resistor sets a current proportional to the current in the lower MOSFET during its conduction interval. UGATE1, UGATE2, and UGATE3 Connect these pins to the corresponding upper MOSFET gates. These pins are used to control the upper MOSFETs and are monitored for shoot-through prevention purposes. Maximum individual channel duty cycle is limited to 66%. BOOT1, BOOT2, and BOOT3 These pins provide the bias voltage for the corresponding upper MOSFET drives. Connect these pins to appropriatelychosen external bootstrap capacitors. Internal bootstrap diodes connected to the PVCC pins provide the necessary bootstrap charge. PHASE1, PHASE2, and PHASE3 Connect these pins to the sources of the corresponding upper MOSFETs. These pins are the return path for the upper MOSFET drives. LGATE1, LGATE2, and LGATE3 These pins are used to control the lower MOSFETs. Connect these pins to the corresponding lower MOSFETs’ gates. PGOOD During normal operation PGOOD indicates whether the output voltage is within specified overvoltage and undervoltage limits. If the output voltage exceeds these limits or a reset event occurs (such as an overcurrent event), PGOOD is pulled low. PGOOD is always low prior to the end of soft-start. The REF input pin is the positive input of the error amplifier. It is internally connected to the DAC output through a 1k resistor. A capacitor is used between the REF pin and ground FN9178 Rev 4.00 Mar 9, 2006 Page 9 of 30 ISL6566 To understand the reduction of ripple current amplitude in the multi-phase circuit, examine the equation representing an individual channel peak-to-peak inductor current. Operation Multi-Phase Power Conversion Microprocessor load current profiles have changed to the point that the advantages of multi-phase power conversion are impossible to ignore. The technical challenges associated with producing a single-phase converter that is both cost-effective and thermally viable have forced a change to the cost-saving approach of multi-phase. The ISL6566 controller helps simplify implementation by integrating vital functions and requiring minimal external components. The block diagram on page 3 provides a top level view of multi-phase power conversion using the ISL6566 controller. IL1 + IL2 + IL3, 7A/DIV IL3, 7A/DIV PWM3, 5V/DIV IL2, 7A/DIV PWM2, 5V/DIV IL1, 7A/DIV PWM1, 5V/DIV 1s/DIV FIGURE 1. PWM AND INDUCTOR-CURRENT WAVEFORMS FOR 3-PHASE CONVERTER Interleaving The switching of each channel in a multi-phase converter is timed to be symmetrically out of phase with each of the other channels. In a 3-phase converter, each channel switches 1/3 cycle after the previous channel and 1/3 cycle before the following channel. As a result, the three-phase converter has a combined ripple frequency three times greater than the ripple frequency of any one phase. In addition, the peak-topeak amplitude of the combined inductor currents is reduced in proportion to the number of phases (Equations 1 and 2). Increased ripple frequency and lower ripple amplitude mean that the designer can use less per-channel inductance and lower total output capacitance for any performance specification. Figure 1 illustrates the multiplicative effect on output ripple frequency. The three channel currents (IL1, IL2, and IL3) combine to form the AC ripple current and the DC load current. The ripple component has three times the ripple frequency of each individual channel current. Each PWM pulse is terminated 1/3 of a cycle after the PWM pulse of the previous phase. The peak-to-peak current for each phase is about 7A, and the dc components of the inductor currents combine to feed the load. FN9178 Rev 4.00 Mar 9, 2006 V IN – V OUT V OUT I PP = ----------------------------------------------------L fS V (EQ. 1) IN In Equation 1, VIN and VOUT are the input and output voltages respectively, L is the single-channel inductor value, and fS is the switching frequency. The output capacitors conduct the ripple component of the inductor current. In the case of multi-phase converters, the capacitor current is the sum of the ripple currents from each of the individual channels. Compare Equation 1 to the expression for the peak-to-peak current after the summation of N symmetrically phase-shifted inductor currents in Equation 2. Peak-to-peak ripple current decreases by an amount proportional to the number of channels. Outputvoltage ripple is a function of capacitance, capacitor equivalent series resistance (ESR), and inductor ripple current. Reducing the inductor ripple current allows the designer to use fewer or less costly output capacitors. V IN – N V OUT V OUT I C, PP = ----------------------------------------------------------L fS V (EQ. 2) IN Another benefit of interleaving is to reduce input ripple current. Input capacitance is determined in part by the maximum input ripple current. Multi-phase topologies can improve overall system cost and size by lowering input ripple current and allowing the designer to reduce the cost of input capacitance. The example in Figure 2 illustrates input currents from a three-phase converter combining to reduce the total input ripple current. The converter depicted in Figure 2 delivers 1.5V to a 36A load from a 12V input. The RMS input capacitor current is 5.9A. Compare this to a single-phase converter also stepping down 12V to 1.5V at 36A. The single-phase converter has 11.9A RMS input capacitor current. The single-phase converter must use an input capacitor bank with twice the RMS current capacity as the equivalent three-phase converter. INPUT-CAPACITOR CURRENT, 10A/DIV CHANNEL 3 INPUT CURRENT 10A/DIV CHANNEL 2 INPUT CURRENT 10A/DIV CHANNEL 1 INPUT CURRENT 10A/DIV 1s/DIV FIGURE 2. CHANNEL INPUT CURRENTS AND INPUTCAPACITOR RMS CURRENT FOR 3-PHASE CONVERTER Page 10 of 30 ISL6566 Figures 22 and 23 in the section entitled Input Capacitor Selection can be used to determine the input-capacitor RMS current based on load current, duty cycle, and the number of channels. They are provided as aids in determining the optimal input capacitor solution. PWM Operation The timing of each converter leg is set by the number of active channels. The default channel setting for the ISL6566 is three. One switching cycle is defined as the time between the internal PWM1 pulse termination signals. The pulse termination signal is the internally generated clock signal that triggers the falling edge of PWM1. The cycle time of the pulse termination signal is the inverse of the switching frequency set by the resistor between the FS pin and ground. Each cycle begins when the clock signal commands PWM1 to go low. The PWM1 transition signals the internal channel-1 MOSFET driver to turn off the channel-1 upper MOSFET and turn on the channel-1 synchronous MOSFET. In the default channel configuration, the PWM2 pulse terminates 1/3 of a cycle after the PWM1 pulse. The PWM3 pulse terminates 1/3 of a cycle after PWM2. If PVCC3 is left open or connected to ground, two channel operation is selected and the PWM2 pulse terminates 1/2 of a cycle after the PWM1 pulse terminates. If both PVCC3 and PVCC2 are left open or connected to ground, single channel operation is selected. Once a PWM pulse transitions low, it is held low for a minimum of 1/3 cycle. This forced off time is required to ensure an accurate current sample. Current sensing is described in the next section. After the forced off time expires, the PWM output is enabled. The PWM output state is driven by the position of the error amplifier output signal, VCOMP, minus the current correction signal relative to the sawtooth ramp as illustrated in Figure 3. When the modified VCOMP voltage crosses the sawtooth ramp, the PWM output transitions high. The internal MOSFET driver detects the change in state of the PWM signal and turns off the synchronous MOSFET and turns on the upper MOSFET. The PWM signal will remain high until the pulse termination signal marks the beginning of the next cycle by triggering the PWM signal low. Channel-Current Balance One important benefit of multi-phase operation is the thermal advantage gained by distributing the dissipated heat over multiple devices and greater area. By doing this the designer avoids the complexity of driving parallel MOSFETs and the expense of using expensive heat sinks and exotic magnetic materials. from each active channel are summed together and divided by the number of active channels. The resulting cycle average current, IAVG, provides a measure of the total loadcurrent demand on the converter during each switching cycle. Channel-current balance is achieved by comparing the sampled current of each channel to the cycle average current, and making the proper adjustment to each channel pulse width based on the error. Intersil’s patented currentbalance method is illustrated in Figure 3, with error correction for channel 1 represented. In the figure, the cycle average current, IAVG, is compared with the channel 1 sample, I1, to create an error signal IER. The filtered error signal modifies the pulse width commanded by VCOMP to correct any unbalance and force IER toward zero. The same method for error signal correction is applied to each active channel. VCOMP + + FILTER PWM1 SAWTOOTH SIGNAL f(s) I3 IER IAVG - + TO GATE CONTROL LOGIC N I2 I1 NOTE: Channel 2 and 3 are optional. FIGURE 3. CHANNEL-1 PWM FUNCTION AND CURRENTBALANCE ADJUSTMENT Current Sampling In order to realize proper current-balance, the currents in each channel must be sampled every switching cycle. This sampling occurs during the forced off-time, following a PWM transition low. During this time the current-sense amplifier uses the ISEN inputs to reproduce a signal proportional to the inductor current, IL. This sensed current, ISEN, is simply a scaled version of the inductor current. The sample window opens exactly 1/6 of the switching period, tSW, after the PWM transitions low. The sample window then stays open the rest of the switching cycle until PWM transitions high again, as illustrated in Figure 4. The sampled current, at the end of the tSAMPLE, is proportional to the inductor current and is held until the next switching period sample. The sampled current is used only for channel-current balance. In order to realize the thermal advantage, it is important that each channel in a multi-phase converter be controlled to carry about the same amount of current at any load level. To achieve this, the currents through each channel must be sampled every switching cycle. The sampled currents, In, FN9178 Rev 4.00 Mar 9, 2006 Page 11 of 30 ISL6566 Output Voltage Setting IL The ISL6566 uses a digital to analog converter (DAC) to generate a reference voltage based on the logic signals at the VID pins. The DAC decodes the 5 or 6-bit logic signals into one of the discrete voltages shown in Tables 2, 3, and 4. Each VID pin is pulled up to an internal 1.2V voltage by a weak current source (40A current), which decreases to 0 as the voltage at the VID pin varies from 0 to the internal 1.2V pull-up voltage. External pull-up resistors or active-high output stages can augment the pull-up current sources, up to a voltage of 5V. PWM SWITCHING PERIOD ISEN The ISL6566 accommodates three different DAC ranges: Intel VRM9.0, AMD Hammer, or Intel VRM10.0. The state of the VRM10 and VID12.5 pins decide which DAC version is active. Refer to Table 1 for a description of how to select the desired DAC version. . SAMPLING PERIOD NEW SAMPLE CURRENT OLD SAMPLE CURRENT TIME TABLE 1. ISL6566 DAC SELECT TABLE FIGURE 4. SAMPLE AND HOLD TIMING The ISL6566 supports MOSFET rDS(ON) current sensing to sample each channel’s current for channel-current balance. The internal circuitry, shown in Figure 5 represents channel n of an N-channel converter. This circuitry is repeated for each channel in the converter, but may not be active depending on the status of the PVCC3 and PVCC2 pins, as described in the PWM Operation section. ISL6565A INTERNAL CIRCUIT VRM9.0 low high AMD HAMMER low low TABLE 2. AMD HAMMER VOLTAGE IDENTIFICATION CODES VDAC 1 1 1 1 1 Off 1 1 1 1 0 0.800 1 1 1 0 1 0.825 1 1 1 0 0 0.850 1 1 0 1 1 0.875 1 1 0 1 0 0.900 1 1 0 0 1 0.925 + CHANNEL N LOWER MOSFET 1 1 0 0 0 0.950 1 0 1 1 1 0.975 EXTERNAL CIRCUIT 1 0 1 1 0 1.000 1 0 1 0 1 1.025 1 0 1 0 0 1.050 1 0 0 1 1 1.075 1 0 0 1 0 1.100 1 0 0 0 1 1.125 1 0 0 0 0 1.150 0 1 1 1 1 1.175 0 1 1 1 0 1.200 0 1 1 0 1 1.225 0 1 1 0 0 1.250 0 1 0 1 1 1.275 0 1 0 1 0 1.300 CHANNEL N UPPER MOSFET RISEN I L r DS ON The ISL6566 senses the channel load current by sampling the voltage across the lower MOSFET rDS(ON), as shown in Figure 5. A ground-referenced operational amplifier, internal to the ISL6566, is connected to the PHASE node through a resistor, RISEN. The voltage across RISEN is equivalent to the voltage drop across the rDS(ON) of the lower MOSFET while it is conducting. The resulting current into the ISEN pin is proportional to the channel current, IL. The ISEN current is sampled and held as described in the Current Sampling section. From Figure 5, the following equation for In is derived where IL is the channel current. FN9178 Rev 4.00 Mar 9, 2006 - VID0 FIGURE 5. ISL6566 INTERNAL AND EXTERNAL CURRENTSENSING CIRCUITRY FOR CURRENT BALANCE r DS ON I n = I L ---------------------R ISEN high VID1 ISEN(n) + VRM10.0 VID2 IL - VID12.5 PIN VID3 r DS ON I SEN = I ------------------------L R ISEN SAMPLE & HOLD VRM10 PIN VID4 VIN In DAC VERSION (EQ. 3) Page 12 of 30 ISL6566 TABLE 2. AMD HAMMER VOLTAGE IDENTIFICATION CODES TABLE 3. VRM9 VOLTAGE IDENTIFICATION CODES (Continued) VID4 VID3 VID2 VID1 VID0 VDAC VID4 VID3 VID2 VID1 VID0 VDAC 0 1 0 0 1 1.325 0 0 1 0 0 1.750 0 1 0 0 0 1.350 0 0 0 1 1 1.775 0 0 1 1 1 1.375 0 0 0 1 0 1.800 0 0 1 1 0 1.400 0 0 0 0 1 1.825 0 0 1 0 1 1.425 0 0 0 0 0 1.850 0 0 1 0 0 1.450 0 0 0 1 1 1.475 0 0 0 1 0 1.500 0 0 0 0 1 1.525 0 0 0 0 0 1.550 TABLE 3. VRM9 VOLTAGE IDENTIFICATION CODES TABLE 4. VRM10 VOLTAGE IDENTIFICATION CODES VID4 VID3 VID2 VID1 VID0 VID12.5 VDAC 1 1 1 1 1 1 Off 1 1 1 1 1 0 Off 0 1 0 1 0 0 0.8375 0 1 0 0 1 1 0.8500 VID4 VID3 VID2 VID1 VID0 VDAC 0 1 0 0 1 0 0.8625 1 1 1 1 1 Off 0 1 0 0 0 1 0.8750 1 1 1 1 0 1.100 0 1 0 0 0 0 0.8875 1 1 1 0 1 1.125 0 0 1 1 1 1 0.9000 1 1 1 0 0 1.150 0 0 1 1 1 0 0.9125 1 1 0 1 1 1.175 0 0 1 1 0 1 0.9250 1 1 0 1 0 1.200 0 0 1 1 0 0 0.9375 1 1 0 0 1 1.225 0 0 1 0 1 1 0.9500 1 1 0 0 0 1.250 0 0 1 0 1 0 0.9625 1 0 1 1 1 1.275 0 0 1 0 0 1 0.9750 1 0 1 1 0 1.300 0 0 1 0 0 0 0.9875 1 0 1 0 1 1.325 0 0 0 1 1 1 1.0000 1 0 1 0 0 1.350 0 0 0 1 1 0 1.0125 1 0 0 1 1 1.375 0 0 0 1 0 1 1.0250 1 0 0 1 0 1.400 0 0 0 1 0 0 1.0375 1 0 0 0 1 1.425 0 0 0 0 1 1 1.0500 1 0 0 0 0 1.450 0 0 0 0 1 0 1.0625 0 1 1 1 1 1.475 0 0 0 0 0 1 1.0750 0 1 1 1 0 1.500 0 0 0 0 0 0 1.0875 0 1 1 0 1 1.525 1 1 1 1 0 1 1.1000 0 1 1 0 0 1.550 1 1 1 1 0 0 1.1125 0 1 0 1 1 1.575 1 1 1 0 1 1 1.1250 0 1 0 1 0 1.600 1 1 1 0 1 0 1.1375 0 1 0 0 1 1.625 1 1 1 0 0 1 1.1500 0 1 0 0 0 1.650 1 1 1 0 0 0 1.1625 0 0 1 1 1 1.675 1 1 0 1 1 1 1.1750 0 0 1 1 0 1.700 1 1 0 1 1 0 1.1875 0 0 1 0 1 1.725 1 1 0 1 0 1 1.2000 FN9178 Rev 4.00 Mar 9, 2006 Page 13 of 30 ISL6566 TABLE 4. VRM10 VOLTAGE IDENTIFICATION CODES (Continued) VID4 VID3 VID2 VID1 VID0 VID12.5 VDAC 1 1 0 1 0 0 1.2125 1 1 0 0 1 1 1.2250 1 1 0 0 1 0 1.2375 1 1 0 0 0 1 1.2500 1 1 0 0 0 0 1.2625 1 0 1 1 1 1 1.2750 1 0 1 1 1 0 1.2875 1 0 1 1 0 1 1.300 1 0 1 1 0 0 1.3125 EXTERNAL CIRCUIT R C CC COMP VID DAC 1k REF CREF FB RFB + VOFS - 1 0 1 1 1.3250 VOUT 1 0 1 0 1 0 1.3375 - 1 0 1 0 0 1 1.3500 1 0 0 0 1.3625 1 0 0 1 1 1 1.3750 1 0 0 1 1 0 1.3875 1 0 0 1 0 1 1.4000 1 0 0 1 0 0 1.4125 1 0 0 0 1 1 1.4250 1 0 0 0 1 0 1.4375 1 0 0 0 0 1 1.4500 1 0 0 0 0 0 1.4625 0 1 1 1 1 1 1.4750 0 1 1 1 1 0 1.4875 0 1 1 1 0 1 1.5000 0 1 1 1 0 0 1.5125 0 1 1 0 1 1 1.5250 0 1 1 0 1 0 1.5375 0 1 1 0 0 1 1.5500 0 1 1 0 0 0 1.5625 0 1 0 1 1 1 1.5750 0 1 0 1 1 0 1.5875 0 1 0 1 0 1 1.6000 Voltage Regulation In order to regulate the output voltage to a specified level, the ISL6566 uses the integrating compensation network shown in Figure 6. This compensation network insures that the steady-state error in the output voltage is limited only to the error in the reference voltage (output of the DAC) and offset errors in the OFS current source, remote-sense and error amplifiers. Intersil specifies the guaranteed tolerance of the ISL6566 to include the combined tolerances of each of these elements. FN9178 Rev 4.00 Mar 9, 2006 - VCOMP ERROR AMPLIFIER VDIFF VSEN 0 0 + IOFS + 1 1 ISL6566 INTERNAL CIRCUIT RGND IREF + - VDROOP - + + ICOMP DIFFERENTIAL REMOTE-SENSE AMPLIFIER FIGURE 6. OUTPUT VOLTAGE AND LOAD-LINE REGULATION WITH OFFSET ADJUSTMENT The ISL6566 incorporates an internal differential remotesense amplifier in the feedback path. The amplifier removes the voltage error encountered when measuring the output voltage relative to the controller ground reference point, resulting in a more accurate means of sensing output voltage. Connect the microprocessor sense pins to the noninverting input, VSEN, and inverting input, RGND, of the remote-sense amplifier. The droop voltage, VDROOP, also feeds into the remote-sense amplifier. The remote-sense output, VDIFF, is therefore equal to the sum of the output voltage, VOUT, and the droop voltage. VDIFF is connected to the inverting input of the error amplifier through an external resistor. The output of the error amplifier, VCOMP, is compared to the sawtooth waveform to generate the PWM signals. The PWM signals control the timing of the Internal MOSFET drivers and regulate the converter output so that the voltage at FB is equal to the voltage at REF. This will regulate the output voltage to be equal to Equation 4. The internal and external circuitry that controls voltage regulation is illustrated in Figure 6. V OUT = V REF – V OFS – V DROOP (EQ. 4) Load-Line (Droop) Regulation Some microprocessor manufacturers require a preciselycontrolled output impedance. This dependence of output voltage on load current is often termed “droop” or “load line” regulation. Page 14 of 30 ISL6566 + PHASE1 RS V L s = I L s L + DCR (EQ. 5) PHASE2 (EQ. 6) sL ------------ R DCR + 1 COMP V s = -------------------------------------------------------------------------- ----------------------- I + I + I DCR DROOP L1 L2 L3 s R C + 1 R COMP COMP S If the R-C network components are selected such that the R-C time constant matches the inductor L/DCR time constant, then VDROOP is equal to the sum of the voltage drops across the individual DCRs, multiplied by a gain. As Equation 7 shows, VDROOP is therefore proportional to the total output current, IOUT. R COMP V DROOP = --------------------- I OUT DCR RS FN9178 Rev 4.00 Mar 9, 2006 (EQ. 7) VOUT COUT DCR INDUCTOR I RS L2 L PHASE3 DCR INDUCTOR I L3 RS - + ISUM CCOMP RCOMP ICOMP VDROOP + The inductor DCR is important because the voltage dropped across it is proportional to the channel current. By using a simple R-C network and a current sense amplifier, as shown in Figure 7, the voltage drop across all of the inductors DCRs can be extracted. The output of the current sense amplifier, VDROOP, can be shown to be proportional to the channel currents IL1, IL2, and IL3, shown in Equation 6. L1 L IOUT DCR INDUCTOR I The droop voltage, VDROOP, is created by sensing the current through the output inductors. This is accomplished by using a continuous DCR current sensing method. Inductor windings have a characteristic distributed resistance or DCR (Direct Current Resistance). For simplicity, the inductor DCR is considered as a separate lumped quantity, as shown in Figure 7. The channel current, IL, flowing through the inductor, passes through the DCR. Equation 5 shows the s-domain equivalent voltage, VL, across the inductor. VL(s) L - As shown in Figure 6, a voltage, VDROOP, proportional to the total current in all active channels, IOUT, feeds into the differential remote-sense amplifier. The resulting voltage at the output of the remote-sense amplifier is the sum of the output voltage and the droop voltage. As Equation 4 shows, feeding this voltage into the compensation network causes the regulator to adjust the output voltage so that it’s equal to the reference voltage minus the droop voltage. (optional) IREF ISL6566 FIGURE 7. DCR SENSING CONFIGURATION By simply adjusting the value of RS, the load line can be set to any level, giving the converter the right amount of droop at all load currents. It may also be necessary to compensate for any changes in DCR due to temperature. These changes cause the load line to be skewed, and cause the R-C time constant to not match the L/DCR time constant. If this becomes a problem a simple negative temperature coefficient resistor network can be used in the place of RCOMP to compensate for the rise in DCR due to temperature. Note: An optional 10nF ceramic capacitor from the ISUM pin to the IREF pin is recommended to help reduce any noise affects on the current sense amplifier due to layout. Output-Voltage Offset Programming The ISL6566 allows the designer to accurately adjust the offset voltage by connecting a resistor, ROFS, from the OFS pin to VCC or GND. When ROFS is connected between OFS and VCC, the voltage across it is regulated to 1.5V. This causes a proportional current (IOFS) to flow into the OFS pin and out of the FB pin. If ROFS is connected to ground, the voltage across it is regulated to 0.5V, and IOFS flows into the FB pin and out of the OFS pin. The offset current flowing through the resistor between VDIFF and FB will generate the desired offset voltage which is equal to the product (IOFS x RFB). These functions are shown in Figures 8 and 9. Page 15 of 30 ISL6566 Dynamic VID VDIFF E/A Modern microprocessors need to make changes to their core voltage as part of normal operation. They direct the corevoltage regulator to do this by making changes to the VID inputs. The core-voltage regulator is required to monitor the DAC inputs and respond to on-the-fly VID changes in a controlled manner, supervising a safe output voltage transition without discontinuity or disruption. + The DAC mode the ISL6566 is operating in determines how the controller responds to a dynamic VID change. When in VRM10 mode the ISL6566 checks the VID inputs six times every switching cycle. If a new code is established and it stays the same for 3 consecutive readings, the ISL6566 recognizes the change and increments the reference. Specific to VRM10, the processor controls the VID transitions and is responsible for incrementing or decrementing one VID step at a time. In VRM10 setting, the ISL6566 will immediately change the reference to the new requested value as soon as the request is validated; in cases where the reference step is too large, the sudden change can trigger overcurrent or overvoltage events. + VOFS - RFB VREF FB IOFS - OFS ISL6566 ROFS - 0.5V GND GND 1.5V + VCC FIGURE 8. POSITIVE OFFSET OUTPUT VOLTAGE PROGRAMMING In order to ensure the smooth transition of output voltage during a VRM10 VID change, a VID step change smoothing network is required for an ISL6566 based voltage regulator. This network is composed of a 1k internal resistor between the output of DAC and the capacitor CREF, between the REF pin and ground. The selection of CREF is based on the time duration for 1 bit VID change and the allowable delay time. VDIFF VOFS + RFB VREF E/A FB IOFS Assuming the microprocessor controls the VID change at 1 bit every TVID, the relationship between CREF and TVID is given by Equation 10. C REF = 0.004X T VID VCC - ROFS OFS ISL6566 - 1.5V + + 0.5V GND VCC FIGURE 9. NEGATIVE OFFSET OUTPUT VOLTAGE PROGRAMMING Once the desired output offset voltage has been determined, use the following formulas to set ROFS: For Positive Offset (connect ROFS to GND): 0.5 R FB R OFS = -------------------------V OFFSET (EQ. 8) For Negative Offset (connect ROFS to VCC): 1.5 R FB R OFS = -------------------------V OFFSET FN9178 Rev 4.00 Mar 9, 2006 (EQ. 9) (EQ. 10) As an example, for a VID step change rate of 5s per bit, the value of CREF is 22nF based on Equation 10. When running in VRM9 or AMD Hammer operation, the ISL6566 responds slightly different to a dynamic VID change than when in VRM10 mode. In these modes the VID code can be changed by more than a 1-bit step at a time. Once the controller receives the new VID code it waits half of a phase cycle and then begins slewing the DAC 12.5mV every phase cycle, until the VID and DAC are equal. Thus, the total time required for a VID change, tDVID, is dependent on the switching frequency (fS), the size of the change (VVID), and the time required to register the VID change. The one-cycle addition in the tDVID equation is due to the possibility that the VID code change may occur up to one full switching cycle before being recognized. The approximate time required for a ISL6566based converter in AMD Hammer configuration running at fS = 335kHz to make a 1.1V to 1.5V reference voltage change is about 100s, as calculated using the following equation. 1 V VID - + 1.5 t DVID = ----- ---------------- f S 0.0125 (EQ. 11) Page 16 of 30 ISL6566 Advanced Adaptive Zero Shoot-Through Deadtime Control (Patent Pending) During turn-off of the lower MOSFET, the PHASE voltage is monitored until it reaches a -0.3V/+0.8V trip point for a forward/reverse current, at which time the UGATE is released to rise. An auto-zero comparator is used to correct the rDS(ON) drop in the phase voltage preventing false detection of the -0.3V phase level during rDS(ON conduction period. In the case of zero current, the UGATE is released after 35ns delay of the LGATE dropping below 0.5V. During the phase detection, the disturbance of LGATE falling transition on the PHASE node is blanked out to prevent falsely tripping. Once the PHASE is high, the advanced adaptive shoot-through circuitry monitors the PHASE and UGATE voltages during a PWM falling edge and the subsequent UGATE turn-off. If either the UGATE falls to less than 1.75V above the PHASE or the PHASE falls to less than +0.8V, the LGATE is released to turn on. 1.4 1.2 CBOOT_CAP (µF) The integrated drivers incorporate a unique adaptive deadtime control technique to minimize deadtime, resulting in high efficiency from the reduced freewheeling time of the lower MOSFET body-diode conduction, and to prevent the upper and lower MOSFETs from conducting simultaneously. This is accomplished by ensuring either rising gate turns on its MOSFET with minimum and sufficient delay after the other has turned off. 1.6 1. 0.8 0.6 QGATE = 100nC 0.4 50nC 0.2 20nC 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 VBOOT_CAP (V) FIGURE 10. BOOTSTRAP CAPACITANCE vs BOOT RIPPLE VOLTAGE Gate Drive Voltage Versatility The ISL6566 provides the user flexibility in choosing the gate drive voltage for efficiency optimization. The controller ties the upper and lower drive rails together. Simply applying a voltage from 5V up to 12V on PVCC sets both gate drive rail voltages simultaneously. Internal Bootstrap Device Initialization All three integrated drivers feature an internal bootstrap schottky diode. Simply adding an external capacitor across the BOOT and PHASE pins completes the bootstrap circuit. The bootstrap function is also designed to prevent the bootstrap capacitor from overcharging due to the large negative swing at the PHASE node. This reduces voltage stress on the boot to phase pins. Prior to initialization, proper conditions must exist on the ENLL, VCC, PVCC and the VID pins. When the conditions are met, the controller begins soft-start. Once the output voltage is within the proper window of operation, the controller asserts PGOOD. The bootstrap capacitor must have a maximum voltage rating above PVCC + 5V and its capacitance value can be chosen from the following equation: Q GATE C BOOT_CAP -------------------------------------V BOOT_CAP (EQ. 12) Q G1 PVCC Q GATE = ------------------------------------ N Q1 V GS1 where QG1 is the amount of gate charge per upper MOSFET at VGS1 gate-source voltage and NQ1 is the number of control MOSFETs. The VBOOT_CAP term is defined as the allowable droop in the rail of the upper gate drive. FN9178 Rev 4.00 Mar 9, 2006 Enable and Disable While in shutdown mode, the PWM outputs are held in a high-impedance state. This forces the drivers to short gateto-source of the upper and lower MOSFET’s to assure the MOSFETs remain off. The following input conditions must be met before the ISL6566 is released from this shutdown mode. 1. The bias voltage applied at VCC must reach the internal power-on reset (POR) rising threshold. Once this threshold is reached, proper operation of all aspects of the ISL6566 is guaranteed. Hysteresis between the rising and falling thresholds assure that once enabled, the ISL6566 will not inadvertently turn off unless the bias voltage drops substantially (see Electrical Specifications). Page 17 of 30 ISL6566 ISL6566 INTERNAL CIRCUIT EXTERNAL CIRCUIT VCC PVCC1 +12V POR CIRCUIT ENABLE COMPARATOR 10.7k ENLL + - 1.40k 0.66V SOFT-START AND FAULT LOGIC FIGURE 11. POWER SEQUENCING USING THRESHOLDSENSITIVE ENABLE (ENLL) FUNCTION 2. The voltage on ENLL must be above 0.66V. The ENLL input allows for power sequencing between the controller bias voltage and another voltage rail. The enable comparator holds the ISL6566 in shutdown until the voltage at ENLL rises above 0.66V. The enable comparator has 60mV of hysteresis to prevent bounce. 3. The driver bias voltage applied at the PVCC pins must reach the internal power-on reset (POR) rising threshold. In order for the ISL6566 to begin operation, PVCC1 is the only pin that is required to have a voltage applied that exceeds POR. However, for 2 or 3-phase operation PVCC2 and PVCC3 must also exceed the POR threshold. Hysteresis between the rising and falling thresholds assure that once enabled, the ISL6566 will not inadvertently turn off unless the PVCC bias voltage drops substantially (see Electrical Specifications). 4. The VID code must not be 111111 or 111110 in VRM10 mode or 11111 in AMD Hammer or VRM9 modes. These codes signal the controller that no load is present. The controller will enter shut-down mode after receiving either of these codes and will execute soft-start upon receiving any other code. These codes can be used to enable or disable the controller but it is not recommended. After receiving one of these codes, the controller executes a 2-cycle delay before changing the overvoltage trip level to the shut-down level and disabling PWM. Overvoltage shutdown cannot be reset using one of these codes. SOFT-START The soft-start function allows the converter to bring up the output voltage in a controlled fashion, resulting in a linear ramp-up. Following a delay of 16 PHASE clock cycles between enabling the chip and the start of the ramp, the output voltage progresses at a fixed rate of 12.5mV per each 16 PHASE clock cycles. Thus, the soft-start period (not including the 16 PHASE clock cycle delay) up to a given voltage, VDAC, can be approximated by the following equation V DAC 1280 T SS = --------------------------------fS (EQ. 13) where VDAC is the DAC-set VID voltage, and fS is the switching frequency. The ISL6566 also has the ability to start up into a precharged output, without causing any unnecessary disturbance. The FB pin is monitored during soft-start, and should it be higher than the equivalent internal ramping reference voltage, the output drives hold both MOSFETs off. Once the internal ramping reference exceeds the FB pin potential, the output drives are enabled, allowing the output to ramp from the pre-charged level to the final level dictated by the DAC setting. Should the output be pre-charged to a level exceeding the DAC setting, the output drives are enabled at the end of the soft-start period, leading to an abrupt correction in the output voltage down to the DAC-set level. OUTPUT PRECHARGED ABOVE DAC LEVEL OUTPUT PRECHARGED BELOW DAC LEVEL GND> VOUT (0.5V/DIV) GND> ENLL (5V/DIV) T1 T2 T3 FIGURE 12. SOFT-START WAVEFORMS FOR ISL6566-BASED MULTI-PHASE CONVERTER When each of these conditions is true, the controller immediately begins the soft-start sequence. FN9178 Rev 4.00 Mar 9, 2006 Page 18 of 30 ISL6566 Fault Monitoring and Protection Undervoltage Detection The ISL6566 actively monitors output voltage and current to detect fault conditions. Fault monitors trigger protective measures to prevent damage to a microprocessor load. One common power good indicator is provided for linking to external system monitors. The schematic in Figure 13 outlines the interaction between the fault monitors and the power good signal. The undervoltage threshold is set at 82% of the VID code. When the output voltage (VSEN-RGND) is below the undervoltage threshold, PGOOD gets pulled low. No other action is taken by the controller. PGOOD will return high if the output voltage rises above 85% of the VID code. ROCSET ICOMP - VOCSET + OCSET IREF + ISEN - VDROOP ISUM 100uA + +1V - + OC + VDIFF - VID + 150mV VOVP + + OV PGOOD x1 - - RGND + 0.82 x DAC UV ISL6566 INTERNAL CIRCUITRY FIGURE 13. POWER GOOD AND PROTECTION CIRCUITRY Power Good Signal The power good pin (PGOOD) is an open-drain logic output that transitions high when the converter is operating after soft-start. PGOOD pulls low during shutdown and releases high after a successful soft-start. PGOOD transitions low when an undervoltage, overvoltage, or overcurrent condition is detected or when the controller is disabled by a reset from ENLL, POR, or one of the no-CPU VID codes. If after an undervoltage or overvoltage event occurs the output returns to within under and overvoltage limits, PGOOD will return high. FN9178 Rev 4.00 Mar 9, 2006 The ISL6566 constantly monitors the difference between the VSEN and RGND voltages to detect if an overvoltage event occurs. During soft-start, while the DAC is ramping up, the overvoltage trip level is the higher of DAC plus 150mV or a fixed voltage, VOVP. The fixed voltage, VOVP, is 1.67V when running in AMD Hammer, or VRM10 modes, and 1.97V for VRM9 mode. Upon successful soft-start, the overvoltage trip level is only DAC plus 150mV. OVP releases 50mV below its trip point if it was “DAC plus 150mV” that tripped it, and releases 100mV below its trip point if it was the fixed voltage, VOVP, that tripped it. Actions are taken by the ISL6566 to protect the microprocessor load when an overvoltage condition occurs, until the output voltage falls back within set limits. At the inception of an overvoltage event, all LGATE signals are commanded high, and the PGOOD signal is driven low. This causes the controller to turn on the lower MOSFETs and pull the output voltage below a level that might cause damage to the load. The LGATE outputs remain high until VDIFF falls to within the overvoltage limits explained above. The ISL6566 will continue to protect the load in this fashion as long as the overvoltage condition recurs. SOFT-START, FAULT AND CONTROL LOGIC VSEN Overvoltage Protection Once an overvoltage condition ends the ISL6566 continues normal operation and PGOOD returns high. Pre-POR Overvoltage Protection Prior to PVCC and VCC exceeding their POR levels, the ISL6566 is designed to protect the load from any overvoltage events that may occur. This is accomplished by means of an internal 10k resistor tied from PHASE to LGATE, which turns on the lower MOSFET to control the output voltage until the overvoltage event ceases or the input power supply cuts off. For complete protection, the low side MOSFET should have a gate threshold well below the maximum voltage rating of the load/microprocessor. In the event that during normal operation the PVCC or VCC voltage falls back below the POR threshold, the pre-POR overvoltage protection circuitry reactivates to protect from any more pre-POR overvoltage events. Open Sense Line Protection In the case that either of the remote sense lines, VSEN or GND, become open, the ISL6566 is designed to detect this and shut down the controller. This event is detected by monitoring the voltage on the IREF pin, which is a local version of VOUT sensed at the outputs of the inductors. Page 19 of 30 ISL6566 If VSEN or RGND become opened, VDIFF falls, causing the duty cycle to increase and the output voltage on IREF to increase. If the voltage on IREF exceeds “VDIFF+1V”, the controller will shut down. Once the voltage on IREF falls below “VDIFF+1V”, the ISL6566 will restart at the beginning of soft-start. power converter. It is assumed that the reader is familiar with many of the basic skills and techniques referenced below. In addition to this guide, Intersil provides complete reference designs that include schematics, bills of materials, and example board layouts for all common microprocessor applications. Power Stages Overcurrent Protection The ISL6566 detects overcurrent events by comparing the droop voltage, VDROOP, to the OCSET voltage, VOCSET, as shown in Figure 13. The droop voltage, set by the external current sensing circuitry, is proportional to the output current as shown in Equation 7. A constant 100A flows through ROCSET, creating the OCSET voltage. When the droop voltage exceeds the OCSET voltage, the overcurrent protection circuitry activates. Since the droop voltage is proportional to the output current, the overcurrent trip level, IMAX, can be set by selecting the proper value for ROCSET, as shown in Equation 14. I MAX R COMP DCR R OCSET = --------------------------------------------------------100 R S (EQ. 14) Once the output current exceeds the overcurrent trip level, VDROOP will exceed VOCSET, and a comparator will trigger the converter to begin overcurrent protection procedures. At the beginning of overcurrent shutdown, the controller turns off both upper and lower MOSFETs. The system remains in this state for a period of 4096 switching cycles. If the controller is still enabled at the end of this wait period, it will attempt a soft-start (as shown in Figure 14). If the fault remains, the trip-retry cycles will continue indefinitely until either the controller is disabled or the fault is cleared. Note that the energy delivered during tripretry cycling is much less than during full-load operation, so there is no thermal hazard. OUTPUT CURRENT, 50A/DIV The first step in designing a multi-phase converter is to determine the number of phases. This determination depends heavily on the cost analysis which in turn depends on system constraints that differ from one design to the next. Principally, the designer will be concerned with whether components can be mounted on both sides of the circuit board, whether through-hole components are permitted, the total board space available for power-supply circuitry, and the maximum amount of load current. Generally speaking, the most economical solutions are those in which each phase handles between 25 and 30A. All surface-mount designs will tend toward the lower end of this current range. If through-hole MOSFETs and inductors can be used, higher per-phase currents are possible. In cases where board space is the limiting constraint, current can be pushed as high as 40A per phase, but these designs require heat sinks and forced air to cool the MOSFETs, inductors and heatdissipating surfaces. MOSFETS The choice of MOSFETs depends on the current each MOSFET will be required to conduct, the switching frequency, the capability of the MOSFETs to dissipate heat, and the availability and nature of heat sinking and air flow. LOWER MOSFET POWER CALCULATION The calculation for power loss in the lower MOSFET is simple, since virtually all of the loss in the lower MOSFET is due to current conducted through the channel resistance (rDS(ON)). In Equation 15, IM is the maximum continuous output current, IPP is the peak-to-peak inductor current (see Equation 1), and d is the duty cycle (VOUT/VIN). I L, 2PP 1 – d I M 2 P LOW 1 = r DS ON ----- 1 – d + -------------------------------12 N 0A OUTPUT VOLTAGE, 500mV/DIV 0V 2ms/DIV FIGURE 14. OVERCURRENT BEHAVIOR IN HICCUP MODE FSW = 500kHz General Design Guide This design guide is intended to provide a high-level explanation of the steps necessary to create a multi-phase FN9178 Rev 4.00 Mar 9, 2006 (EQ. 15) An additional term can be added to the lower-MOSFET loss equation to account for additional loss accrued during the dead time when inductor current is flowing through the lower-MOSFET body diode. This term is dependent on the diode forward voltage at IM, VD(ON), the switching frequency, fS, and the length of dead times, td1 and td2, at the beginning and the end of the lower-MOSFET conduction interval respectively. I I M I PP M I PP t P LOW 2 = V D ON f S ----- t d1 + ----- – --------- d2 N- + -------2 2 N (EQ. 16) The total maximum power dissipated in each lower MOSFET is approximated by the summation of PLOW,1 and PLOW,2. Page 20 of 30 ISL6566 UPPER MOSFET POWER CALCULATION In addition to rDS(ON) losses, a large portion of the upperMOSFET losses are due to currents conducted across the input voltage (VIN) during switching. Since a substantially higher portion of the upper-MOSFET losses are dependent on switching frequency, the power calculation is more complex. Upper MOSFET losses can be divided into separate components involving the upper-MOSFET switching times, the lower-MOSFET body-diode reverserecovery charge, Qrr, and the upper MOSFET rDS(ON) conduction loss. When the upper MOSFET turns off, the lower MOSFET does not conduct any portion of the inductor current until the voltage at the phase node falls below ground. Once the lower MOSFET begins conducting, the current in the upper MOSFET falls to zero as the current in the lower MOSFET ramps up to assume the full inductor current. In Equation 17, the required time for this commutation is t1 and the approximated associated power loss is PUP,1. I M I PP t 1 P UP,1 V IN ----- ---- f N- + -------2 2 S (EQ. 17) At turn on, the upper MOSFET begins to conduct and this transition occurs over a time t2. In Equation 18, the approximate power loss is PUP,2. I M I PP t 2 P UP, 2 V IN ----- ---- f N- – -------2 2 S (EQ. 18) A third component involves the lower MOSFET reverserecovery charge, Qrr. Since the inductor current has fully commutated to the upper MOSFET before the lowerMOSFET body diode can recover all of Qrr, it is conducted through the upper MOSFET across VIN. The power dissipated as a result is PUP,3. (EQ. 19) P UP,3 = V IN Q rr f S Finally, the resistive part of the upper MOSFET is given in Equation 20 as PUP,4. 2 I PP2 I M P UP,4 r DS ON ----- d + ---------12 N (EQ. 20) The total power dissipated by the upper MOSFET at full load can now be approximated as the summation of the results from Equations 17, 18, 19 and 20. Since the power equations depend on MOSFET parameters, choosing the correct MOSFETs can be an iterative process involving repetitive solutions to the loss equations for different MOSFETs and different switching frequencies. by all three drivers must be less than the maximum allowable power dissipation for the QFN package. Calculating the power dissipation in the drivers for a desired application is critical to ensure safe operation. Exceeding the maximum allowable power dissipation level will push the IC beyond the maximum recommended operating junction temperature of 125°C. The maximum allowable IC power dissipation for the 6x6 QFN package is approximately 4W at room temperature. See Layout Considerations paragraph for thermal transfer improvement suggestions. When designing the ISL6566 into an application, it is recommended that the following calculation is used to ensure safe operation at the desired frequency for the selected MOSFETs. The total gate drive power losses, PQg_TOT, due to the gate charge of MOSFETs and the integrated driver’s internal circuitry and their corresponding average driver current can be estimated with Equations 21 and 22, respectively. P Qg_TOT = P Qg_Q1 + P Qg_Q2 + I Q VCC (EQ. 21) 3 P Qg_Q1 = --- Q G1 PVCC F SW N Q1 N PHASE 2 P Qg_Q2 = Q G2 PVCC F SW N Q2 N PHASE 3 I DR = --- Q G1 N + Q G2 N Q2 N PHASE F SW + I Q 2 Q1 (EQ. 22) In Equations 21 and 22, PQg_Q1 is the total upper gate drive power loss and PQg_Q2 is the total lower gate drive power loss; the gate charge (QG1 and QG2) is defined at the particular gate to source drive voltage PVCC in the corresponding MOSFET data sheet; IQ is the driver total quiescent current with no load at both drive outputs; NQ1 and NQ2 are the number of upper and lower MOSFETs per phase, respectively; NPHASE is the number of active phases. The IQ*VCC product is the quiescent power of the controller without capacitive load and is typically 75mW at 300kHz. PVCC BOOT D CGD RHI1 RLO1 UGATE G RG1 CDS RGI1 CGS Q1 S Package Power Dissipation When choosing MOSFETs it is important to consider the amount of power being dissipated in the integrated drivers located in the controller. Since there are a total of three drivers in the controller package, the total power dissipated FN9178 Rev 4.00 Mar 9, 2006 PHASE FIGURE 15. TYPICAL UPPER-GATE DRIVE TURN-ON PATH Page 21 of 30 ISL6566 PVCC VIN D CHANNEL N UPPER MOSFET CGD RHI2 LGATE RLO2 G RG2 IL CDS RGI2 ISEN(n) CGS Q2 RISEN S ISL6566 I + CHANNEL N LOWER MOSFET FIGURE 16. TYPICAL LOWER-GATE DRIVE TURN-ON PATH The total gate drive power losses are dissipated among the resistive components along the transition path and in the bootstrap diode. The portion of the total power dissipated in the controller itself is the power dissipated in the upper drive path resistance, PDR_UP, the lower drive path resistance, PDR_UP, and in the boot strap diode, PBOOT. The rest of the power will be dissipated by the external gate resistors (RG1 and RG2) and the internal gate resistors (RGI1 and RGI2) of the MOSFETs. Figures 15 and 16 show the typical upper and lower gate drives turn-on transition path. The total power dissipation in the controller itself, PDR, can be roughly estimated as: P DR = P DR_UP + P DR_LOW + P BOOT + I Q VCC (EQ. 23) P Qg_Q1 P BOOT = --------------------3 R HI1 R LO1 P Qg_Q1 P DR_UP = -------------------------------------+ --------------------------------------- --------------------3 R HI1 + R EXT1 R LO1 + R EXT1 R LO2 R HI2 P Qg_Q2 + --------------------------------------- --------------------P DR_LOW = -------------------------------------2 R HI2 + R EXT2 R LO2 + R EXT2 R GI1 R EXT1 = R G1 + ------------N Q1 R GI2 R EXT2 = R G2 + ------------N Q2 Current Balancing Component Selection The ISL6566 senses the channel load current by sampling the voltage across the lower MOSFET rDS(ON), as shown in Figure 17. The ISEN pins are denoted ISEN1, ISEN2, and ISEN3. The resistors connected between these pins and the respective phase nodes determine the gains in the channelcurrent balance loop. r L DS ON FIGURE 17. ISL6566 INTERNAL AND EXTERNAL CURRENTSENSING CIRCUITRY Select values for these resistors based on the room temperature rDS(ON) of the lower MOSFETs; the full-load operating current, IFL; and the number of phases, N using Equation 24. r DS ON R ISEN = ---------------------– 50 10 6 I FL ------N (EQ. 24) In certain circumstances, it may be necessary to adjust the value of one or more ISEN resistors. When the components of one or more channels are inhibited from effectively dissipating their heat so that the affected channels run hotter than desired, choose new, smaller values of RISEN for the affected phases (see the section entitled Channel-Current Balance). Choose RISEN,2 in proportion to the desired decrease in temperature rise in order to cause proportionally less current to flow in the hotter phase. T R ISEN ,2 = R ISEN ----------2 T 1 (EQ. 25) In Equation 25, make sure that T2 is the desired temperature rise above the ambient temperature, and T1 is the measured temperature rise above the ambient temperature. While a single adjustment according to Equation 25 is usually sufficient, it may occasionally be necessary to adjust RISEN two or more times to achieve optimal thermal balance between all channels. Load Line Regulation Component Selection (DCR Current Sensing) For accurate load line regulation, the ISL6566 senses the total output current by detecting the voltage across the output inductor DCR of each channel (As described in the Load Line Regulation section). As Figure 18 illustrates, an R-C network is required to accurately sense the inductor DCR voltage and convert this information into a “droop” voltage, which is proportional to the total output current. Choosing the components for this current sense network is a two step process. First, RCOMP and CCOMP must be chosen so that the time constant of this RCOMP-CCOMP network matches the time constant of the inductor L/DCR. FN9178 Rev 4.00 Mar 9, 2006 Page 22 of 30 ISL6566 Then the resistor RS must be chosen to set the current sense network gain, obtaining the desired full load droop voltage. Follow the steps below to choose the component values for this R-C network. 1. Choose an arbitrary value for CCOMP. The recommended value is 0.01F. 3. Select a new value, RCOMP,2, for the time constant resistor based on the original value, RCOMP,1, using the following equation. 2. Plug the inductor L and DCR component values, and the values for CCOMP chosen in steps 1, into Equation 26 to calculate the value for RCOMP. 4. Replace RCOMP with the new value and check to see that the error is corrected. Repeat the procedure if necessary. L R COMP = --------------------------------------DCR C COMP (EQ. 26) 3. Use the new value for RCOMP obtained from Equation 26, as well as the desired full load current, IFL, full load droop voltage, VDROOP, and inductor DCR in Equation 27 to calculate the value for RS. I FL R S = ------------------------- R COMP DCR V DROOP (EQ. 27) + VL(s) RS - PHASE1 L V2 V1 IOUT ITRAN RS DCR FIGURE 19. TIME CONSTANT MISMATCH BEHAVIOR L2 Compensation L PHASE3 DCR INDUCTOR I L3 RS ISUM - CCOMP I COUT INDUCTOR I + After choosing a new value for RCOMP, it will most likely be necessary to adjust the value of RS to obtain the desired full load droop voltage. Use Equation 27 to obtain the new value for RS. DCR INDUCTOR I L1 PHASE2 RCOMP ICOMP + (EQ. 28) 2 VOUT L VDROOP V 1 R COMP 2 = R COMP 1 ---------V The two opposing goals of compensating the voltage regulator are stability and speed. The load-line regulated converter behaves in a similar manner to a peak current mode controller because the two poles at the output filter L-C resonant frequency split with the introduction of current information into the control loop. The final location of these poles is determined by the system function, the gain of the current signal, and the value of the compensation components, RC and CC. C2 (OPTIONAL) (optional) IREF RC ISL6566 CC COMP FIGURE 18. DCR SENSING CONFIGURATION FB Due to errors in the inductance or DCR it may be necessary to adjust the value of RCOMP to match the time constants correctly. The effects of time constant mismatch can be seen in the form of droop overshoot or undershoot during the initial load transient spike, as shown in Figure 19. Follow the steps below to ensure the R-C and inductor L/DCR time constants are matched accurately. 1. Capture a transient event with the oscilloscope set to about L/DCR/2 (sec/div). For example, with L = 1H and DCR = 1m, set the oscilloscope to 500s/div. 2. Record V1 and V2 as shown in Figure 19. FN9178 Rev 4.00 Mar 9, 2006 ISL6566 RFB VDIFF FIGURE 20. COMPENSATION CONFIGURATION FOR LOAD-LINE REGULATED ISL6566 CIRCUIT Since the system poles and zero are affected by the values of the components that are meant to compensate them, the solution to the system equation becomes fairly complicated. Page 23 of 30 ISL6566 Fortunately, there is a simple approximation that comes very close to an optimal solution. Treating the system as though it were a voltage-mode regulator, by compensating the L-C poles and the ESR zero of the voltage mode approximation, yields a solution that is always stable with very close to ideal transient performance. Select a target bandwidth for the compensated system, f0. The target bandwidth must be large enough to assure adequate transient performance, but smaller than 1/3 of the per-channel switching frequency. The values of the compensation components depend on the relationships of f0 to the L-C pole frequency and the ESR zero frequency. For each of the following three, there is a separate set of equations for the compensation components. Case 1: 1 ------------------- > f 0 2 LC 2f 0 V pp LC R C = R FB ----------------------------------0.66V IN 0.66V IN C C = ----------------------------------2V PP R FB f 0 Case 2: 1 1 ------------------- f 0 < ----------------------------2C ESR 2 LC V PP 2 2 f 02 LC R C = R FB -------------------------------------------0.66 V (EQ. 29) IN 0.66V IN C C = -----------------------------------------------------------2 2 f 02 V PP R FB LC Case 3: 1 f 0 > -----------------------------2C ESR 2 f 0 V pp L R C = R FB ----------------------------------------0.66 V IN ESR 0.66V IN ESR C C C = -----------------------------------------------2V PP R FB f 0 L In Equations 29, L is the per-channel filter inductance divided by the number of active channels; C is the sum total of all output capacitors; ESR is the equivalent series resistance of the bulk output filter capacitance; and VPP is the peak-to-peak sawtooth signal amplitude as described in the Electrical Specifications. Once selected, the compensation values in Equations 29 assure a stable converter with reasonable transient performance. In most cases, transient performance can be improved by making adjustments to RC. Slowly increase the value of RC while observing the transient performance on an oscilloscope until no further improvement is noted. Normally, CC will not need adjustment. Keep the value of CC from Equations 29 unless some performance issue is noted. The optional capacitor C2, is sometimes needed to bypass noise away from the PWM comparator (see Figure 20). Keep a position available for C2, and be prepared to install a high- FN9178 Rev 4.00 Mar 9, 2006 frequency capacitor of between 22pF and 150pF in case any leading edge jitter problem is noted. Output Filter Design The output inductors and the output capacitor bank together to form a low-pass filter responsible for smoothing the pulsating voltage at the phase nodes. The output filter also must provide the transient energy until the regulator can respond. Because it has a low bandwidth compared to the switching frequency, the output filter limits the system transient response. The output capacitors must supply or sink load current while the current in the output inductors increases or decreases to meet the demand. In high-speed converters, the output capacitor bank is usually the most costly (and often the largest) part of the circuit. Output filter design begins with minimizing the cost of this part of the circuit. The critical load parameters in choosing the output capacitors are the maximum size of the load step, I, the loadcurrent slew rate, di/dt, and the maximum allowable outputvoltage deviation under transient loading, VMAX. Capacitors are characterized according to their capacitance, ESR, and ESL (equivalent series inductance). At the beginning of the load transient, the output capacitors supply all of the transient current. The output voltage will initially deviate by an amount approximated by the voltage drop across the ESL. As the load current increases, the voltage drop across the ESR increases linearly until the load current reaches its final value. The capacitors selected must have sufficiently low ESL and ESR so that the total output-voltage deviation is less than the allowable maximum. Neglecting the contribution of inductor current and regulator response, the output voltage initially deviates by an amount di V ESL ----- + ESR I dt (EQ. 30) The filter capacitor must have sufficiently low ESL and ESR so that V < VMAX. Most capacitor solutions rely on a mixture of high frequency capacitors with relatively low capacitance in combination with bulk capacitors having high capacitance but limited highfrequency performance. Minimizing the ESL of the highfrequency capacitors allows them to support the output voltage as the current increases. Minimizing the ESR of the bulk capacitors allows them to supply the increased current with less output voltage deviation. The ESR of the bulk capacitors also creates the majority of the output-voltage ripple. As the bulk capacitors sink and source the inductor ac ripple current (see Interleaving and Equation 2), a voltage develops across the bulk capacitor ESR equal to IC,PP(ESR). Thus, once the output capacitors are selected, the maximum allowable ripple voltage, VPP(MAX), determines the lower limit on the inductance. V – N V OUT V OUT IN L ESR -----------------------------------------------------------f S V IN V PP MAX (EQ. 31) Page 24 of 30 ISL6566 Equation 32 gives the upper limit on L for the cases when the trailing edge of the current transient causes a greater outputvoltage deviation than the leading edge. Equation 33 addresses the leading edge. Normally, the trailing edge dictates the selection of L because duty cycles are usually less than 50%. Nevertheless, both inequalities should be evaluated, and L should be selected based on the lower of the two results. In each equation, L is the per-channel inductance, C is the total output capacitance, and N is the number of active channels. 2 N C VO L --------------------------------- V MAX – I ESR I 2 (EQ. 32) 1.25 N C L ---------------------------------- V MAX – I ESR V IN – V O I 2 (EQ. 33) Input Capacitor Selection The input capacitors are responsible for sourcing the ac component of the input current flowing into the upper MOSFETs. Their RMS current capacity must be sufficient to handle the ac component of the current drawn by the upper MOSFETs which is related to duty cycle and the number of active phases. 0.3 INPUT-CAPACITOR CURRENT (IRMS/IO) Since the capacitors are supplying a decreasing portion of the load current while the regulator recovers from the transient, the capacitor voltage becomes slightly depleted. The output inductors must be capable of assuming the entire load current before the output voltage decreases more than VMAX. This places an upper limit on inductance. IL,PP = 0 IL,PP = 0.5 IO IL,PP = 0.25 IO IL,PP = 0.75 IO 0.2 0.1 0 0 0.2 Switching Frequency There are a number of variables to consider when choosing the switching frequency, as there are considerable effects on the upper MOSFET loss calculation. These effects are outlined in MOSFETs, and they establish the upper limit for the switching frequency. The lower limit is established by the requirement for fast transient response and small output-voltage ripple as outlined in Output Filter Design. Choose the lowest switching frequency that allows the regulator to meet the transientresponse requirements. Switching frequency is determined by the selection of the frequency-setting resistor, RT. Figure 21 and Equation 34 are provided to assist in selecting the correct value for RT. R T = 10 0.6 0.8 1.0 (EQ. 34) 10.61 – 1.035 log f S FIGURE 22. NORMALIZED INPUT-CAPACITOR RMS CURRENT FOR 3-PHASE CONVERTER For a three-phase design, use Figure 22 to determine the inputcapacitor RMS current requirement set by the duty cycle, maximum sustained output current (IO), and the ratio of the peak-to-peak inductor current (IL,PP) to IO. Select a bulk capacitor with a ripple current rating which will minimize the total number of input capacitors required to support the RMS current calculated. The voltage rating of the capacitors should also be at least 1.25 times greater than the maximum input voltage. Figures 23 and 24 provide the same input RMS current information for two-phase and single-phase designs respectively. Use the same approach for selecting the bulk capacitor type and number. 1000 0.3 INPUT-CAPACITOR CURRENT (IRMS/IO) RT (k) 0.4 DUTY CYCLE (VIN/VO) 100 10 10 100 1000 10000 SWITCHING FREQUENCY (kHz) 0.2 0.1 IL,PP = 0 IL,PP = 0.5 IO IL,PP = 0.75 IO 0 0 0.2 0.4 0.6 0.8 DUTY CYCLE (VIN/VO) FIGURE 21. RT vs SWITCHING FREQUENCY FN9178 Rev 4.00 Mar 9, 2006 FIGURE 23. NORMALIZED INPUT-CAPACITOR RMS CURRENT FOR 2-PHASE CONVERTER Page 25 of 30 1.0 ISL6566 all three power trains. Equidistant placement of the controller to the three power trains also helps keep the gate drive traces equally short, resulting in equal trace impedances and similar drive capability of all sets of MOSFETs. INPUT-CAPACITOR CURRENT (IRMS/IO) 0.6 0.4 0.2 IL,PP = 0 IL,PP = 0.5 IO IL,PP = 0.75 IO 0 0 0.2 0.4 0.6 0.8 1.0 DUTY CYCLE (VIN/VO) FIGURE 24. NORMALIZED INPUT-CAPACITOR RMS CURRENT FOR SINGLE-PHASE CONVERTER Low capacitance, high-frequency ceramic capacitors are needed in addition to the input bulk capacitors to suppress leading and falling edge voltage spikes. The spikes result from the high current slew rate produced by the upper MOSFET turn on and off. Select low ESL ceramic capacitors and place one as close as possible to each upper MOSFET drain to minimize board parasitics and maximize suppression. Layout Considerations MOSFETs switch very fast and efficiently. The speed with which the current transitions from one device to another causes voltage spikes across the interconnecting impedances and parasitic circuit elements. These voltage spikes can degrade efficiency, radiate noise into the circuit and lead to device overvoltage stress. Careful component selection, layout, and placement minimizes these voltage spikes. Consider, as an example, the turnoff transition of the upper PWM MOSFET. Prior to turnoff, the upper MOSFET was carrying channel current. During the turnoff, current stops flowing in the upper MOSFET and is picked up by the lower MOSFET. Any inductance in the switched current path generates a large voltage spike during the switching interval. Careful component selection, tight layout of the critical components, and short, wide circuit traces minimize the magnitude of voltage spikes. There are two sets of critical components in a DC-DC converter using a ISL6566 controller. The power components are the most critical because they switch large amounts of energy. Next are small signal components that connect to sensitive nodes or supply critical bypassing current and signal coupling. The power components should be placed first, which include the MOSFETs, input and output capacitors, and the inductors. It is important to have a symmetrical layout for each power train, preferably with the controller located equidistant from each. Symmetrical layout allows heat to be dissipated equally across FN9178 Rev 4.00 Mar 9, 2006 When placing the MOSFETs try to keep the source of the upper FETs and the drain of the lower FETs as close as thermally possible. Input Bulk capacitors should be placed close to the drain of the upper FETs and the source of the lower FETs. Locate the output inductors and output capacitors between the MOSFETs and the load. The high-frequency input and output decoupling capacitors (ceramic) should be placed as close as practicable to the decoupling target, making use of the shortest connection paths to any internal planes, such as vias to GND next or on the capacitor solder pad. The critical small components include the bypass capacitors for VCC and PVCC, and many of the components surrounding the controller including the feedback network and current sense components. Locate the VCC/PVCC bypass capacitors as close to the ISL6566 as possible. It is especially important to locate the components associated with the feedback circuit close to their respective controller pins, since they belong to a high-impedance circuit loop, sensitive to EMI pick-up. It is also important to place the current sense components close to their respective pins on the ISL6566, including RISEN, RS, RCOMP, and CCOMP. A multi-layer printed circuit board is recommended. Figure 25 shows the connections of the critical components for the converter. Note that capacitors CxxIN and CxxOUT could each represent numerous physical capacitors. Dedicate one solid layer, usually the one underneath the component side of the board, for a ground plane and make all critical component ground connections with vias to this layer. Dedicate another solid layer as a power plane and break this plane into smaller islands of common voltage levels. Keep the metal runs from the PHASE terminal to output inductors short. The power plane should support the input power and output power nodes. Use copper filled polygons on the top and bottom circuit layers for the phase nodes. Use the remaining printed circuit layers for small signal wiring. Routing UGATE, LGATE, and PHASE traces Great attention should be paid to routing the UGATE, LGATE, and PHASE traces since they drive the power train MOSFETs using short, high current pulses. It is important to size them as large and as short as possible to reduce their overall impedance and inductance. They should be sized to carry at least one ampere of current (0.02” to 0.05”). Going between layers with vias should also be avoided, but if so, use two vias for interconnection when possible. Extra care should be given to the LGATE traces in particular since keeping their impedance and inductance low helps to significantly reduce the possibility of shoot-through. It is also important to route each channels UGATE and PHASE traces in as close proximity as possible to reduce their inductances. Page 26 of 30 ISL6566 Thermal Management For maximum thermal performance in high current, high switching frequency applications, connecting the thermal GND pad of the ISL6566 to the ground plane with multiple vias is recommended. This heat spreading allows the part to achieve its full thermal potential. It is also recommended that the controller be placed in a direct path of airflow if possible to help thermally manage the part. Suppressing MOSFET Gate Leakage With VCC at ground potential, UGATE is high impedance. In this state, any stray leakage has the potential to deliver charge to the gate of the upper MOSFET. If UGATE receives sufficient charge to bias the device on, a low impedance path will be connected between the upper MOSFET drain and PHASE. If this occurs and the input power supply is present and active, the system could see potentially damaging current. Worst-case leakage currents are on the order of pico-amps; therefore, a 10k resistor, connected from UGATE to PHASE, is more than sufficient to bleed off any stray leakage current. This resistor will not affect the normal performance of the driver or reduce its efficiency. FN9178 Rev 4.00 Mar 9, 2006 Page 27 of 30 ISL6566 LOCATE CLOSE TO IC (MINIMIZE CONNECTION PATH) C2 KEY HEAVY TRACE ON CIRCUIT PLANE LAYER RFB ISLAND ON POWER PLANE LAYER +12V C1 VDIFF ISLAND ON CIRCUIT PLANE LAYER R1 FB VIA CONNECTION TO GROUND PLANE COMP PVCC1 (CF2) CBIN1 BOOT1 LOCATE NEAR SWITCHING TRANSISTORS; (MINIMIZE CONNECTION PATH) CBOOT1 VSEN UGATE1 RGND +5V PHASE1 VCC (CF1) ISEN1 RISEN1 LGATE1 ROFS OFS +12V FS RT PVCC2 REF (CF2) CREF CBIN2 BOOT2 CBOOT2 VID4 ISL6566 UGATE2 VID3 PHASE2 VID2 ISEN2 CBOUT (CHFOUT) RISEN2 VID1 LOAD LGATE2 VID0 VID12.5 +12V VRM10 PGOOD CBIN3 PVCC3 (CF2) +12V BOOT3 GND LOCATE NEAR LOAD; (MINIMIZE CONNECTION PATH) CBOOT3 UGATE3 PHASE3 ENLL ISEN3 IREF RISEN3 OCSET ICOMP ISUM RCOMP LGATE3 RS RS ROCSET RS CCOMP FIGURE 25. PRINTED CIRCUIT BOARD POWER PLANES AND ISLANDS FN9178 Rev 4.00 Mar 9, 2006 Page 28 of 30 ISL6566 © Copyright Intersil Americas LLC 2004-2006. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN9178 Rev 4.00 Mar 9, 2006 Page 29 of 30 ISL6566 Quad Flat No-Lead Plastic Package (QFN) Micro Lead Frame Plastic Package (MLFP) 2X 9 MILLIMETERS D/2 D1 D1/2 2X N 6 INDEX AREA 40 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220VJJD-2 ISSUE C) 0.15 C A D A L40.6x6 0.15 C B SYMBOL MIN NOMINAL MAX NOTES A 0.80 0.90 1.00 - A1 - - 0.05 - A2 - - 1.00 A3 1 2 3 E1/2 E/2 E1 b D2 0.15 C B 0.15 C A 4X B TOP VIEW 0 A C 0.08 C SEATING PLANE A1 A3 SIDE VIEW 9 5 NX b 0.10 M C A B 4X P D2 (DATUM B) 8 7 NX k D2 2 N 4X P 4.10 (Ne-1)Xe REF. E2 N e 8 6.00 BSC - 5.75 BSC 9 3.95 4.10 k 0.25 - - - L 0.30 0.40 0.50 8 L1 - - 0.15 10 N 40 2 Nd 10 3 Ne 10 3 P - - 0.60 9 - - 12 9 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. NX b 5 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. SECTION "C-C" L1 10 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. C L L e L1 10 L e C C TERMINAL TIP FN9178 Rev 4.00 Mar 9, 2006 - 3. Nd and Ne refer to the number of terminals on each D and E. A1 FOR ODD TERMINAL/SIDE 7, 8 2. N is the number of terminals. 8 BOTTOM VIEW C L 4.25 0.50 BSC 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 9 CORNER OPTION 4X (Nd-1)Xe REF. 7, 8 NOTES: 7 E2/2 NX L 9 4.25 Rev. 1 10/02 2 3 6 INDEX AREA - E 1 (DATUM A) 5, 8 5.75 BSC 3.95 e / / 0.10 C 0.30 E1 E2 A2 0.23 9 6.00 BSC D1 9 2X 2X 0.18 D E 9 0.20 REF 9. Features and dimensions A2, A3, D1, E1, P & are present when Anvil singulation method is used and not present for saw singulation. 10. Depending on the method of lead termination at the edge of the package, a maximum 0.15mm pull back (L1) maybe present. L minus L1 to be equal to or greater than 0.3mm. FOR EVEN TERMINAL/SIDE Page 30 of 30