JSM10 Series DC-DC Converter 10 Watts xxx Series • Regulated Single & Dual Output • 2:1 Input Range • 1” x 1” Package • 1500 VDC Isolation • Operating Temperature -40 °C to +100 °C • ITE Safety Approvals • Optional Remote On/Off • Optional Heatsink • Metal Case Dimensions: • 3 Year Warranty JSM10: 1.00 x 1.00 x 0.40” (25.4 x 25.4 x 10.16 mm) Models & Ratings Input voltage 9-18V 18-36V 36-75V Output voltage Output current Input current(1,2) No load Full load Maximum capacitive load(3) Efficiency Model number(4) JSM1012S3V3 3V3 2.50 A 840 mA 4700 µF 82% 5V 2.00 A 980 mA 2200 µF 85% JSM1012S05 5.1 V 2.00 A 1000 mA 2200 µF 85% JSM1012S5V1 12 V 0.83 A 955 mA 330 µF 87% JSM1012S12 15 V 0.67 A 950 mA 220 µF 88% JSM1012S15 ±5 V ±1.000 A 990 mA ±1000 µF 84% JSM1012D05 ±12 V ±0.416 A 955 mA ±150 µF 87% JSM1012D12 ±15 V ±0.333 A 955 mA ±100 µF 87% JSM1012D15 3V3 2.50 A 415 mA 4700 µF 83% JSM1024S3V3 15 mA 5V 2.00 A 490 mA 2200 µF 85% JSM1024S05 5.1 V 2.00 A 500 mA 2200 µF 85% JSM1024S5V1 12 V 0.83 A 470 mA 330 µF 88% JSM1024S12 15 V 0.67 A 470 mA 220 µF 89% JSM1024S15 ±5 V ±1.000 A 490 mA ±1000 µF 85% JSM1024D05 ±12 V ±0.416 A 475 mA ±150 µF 88% JSM1024D12 ±15 V ±0.333 A 470 mA ±100 µF 89% JSM1024D15 3V3 2.50 A 205 mA 4700 µF 83% JSM1048S3V3 12 mA 5V 2.00 A 240 mA 2200 µF 86% JSM1048S05 5.1 V 2.00 A 250 mA 2200 µF 85% JSM1048S5V1 12 V 0.83 A 235 mA 330 µF 89% JSM1048S12 15 V 0.67 A 235 mA 220 µF 89% JSM1048S15 ±5 V ±1.000 A 240 mA ±1000 µF 86% JSM1048D05 ±12 V ±0.416 A 240 mA ±150 µF 87% JSM1048D12 ±15 V ±0.333 A 235 mA ±100 µF 88% JSM1048D15 10 mA Notes 1. Input currents measured at nominal input voltage. 2. Input current is typically 5 mA at nominal input voltage when output is turned off with optional remote on/off. 3. Maximum capacitive load is per output. 4. Add suffix “-R” for optional remote on/off, “-HK” for optional heatsink or “-RHK” for optional remote on/off and heatsink. 1 www.xppower.com JSM10 Series DC-DC Converter Input Characteristic Input Voltage Range Input Filter Minimum Typical Notes & Conditions Maximum Units 9.0 18 VDC 12 V nominal 18.0 36 VDC 24 V nominal 36.0 75 VDC 48 V nominal VDC for 1 s 24 V models Internal Pi type 12 V models 25 50 Input Surge 100 48 V models ON at >9V, OFF at <8.5 V 12 V models Undervoltage Lockout ON at >18V, OFF at <17 V 24 V models ON at >36V, OFF at <34 V 48 V models Remote On/Off ON: Logic high (3.5-12 V) or open circuit OFF: Logic low (<1.2 V) or short pin 2 to pin 6 Output Characteristic Minimum Output Voltage 3.3 Typical Maximum Units Notes & Conditions 30 VDC See Models and Ratings table Initial Set Accuracy ±2.0 % Output Voltage Balance ±2.0 % For dual output with balanced laods A No minimum load required Minimum Load At full load Line Regulation ±1.0 % From minimum to maximum input at full load Load Regulation ±0.5/±1.0 % Single / Dual output, from 0 to full load Cross Regulation ±5.0 % On dual output models when one load is varied between 25% and 100% and other is fixed at 100% 5 % deviation Transient Response 3 Ripple & Noise Overload Protection 80/100 mV pk-pk 150 % Short Circuit Protection Recovery within 1% in less than 300 µs for a 25% load change. 3.3 & 5V output / other models. 20 MHz bandwidth. Measured using 0.47 µF ceramic capacitor. Continuous Trip & Restart (Hiccup mode), with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.02 %/ ˚C Maximum Units General Characteristic Minimum Typical Efficiency Isolation: Input to Output Isolation Resistance 85 % 60 s/1 s pF kHz At 500 VDC 2000 50.8 W/in3 Ω 109 Switching Frequency 330 Power Density Mean Time Between Failure Weight See Models and Ratings table VDC 1500/1800 Isolation Capacitance Notes & Conditions 2.5 MHrs 0.03 (15.0) lb (g) MIL-HDBK-217F, +25 °C GB Environmental Characteristic Minimum Operating Temperature -40 Storage Temperature -50 Typical Case Temperature Humidity Maximum Units Notes & Conditions +100 °C See Derating Curve. +125 °C +100 °C 95 %RH Cooling Non-condensing Natural convection EMC: Emissions Phenomenon Standard Test Level Conducted EN55022 Class A www.xppower.com Notes & Conditions 2 JSM10 Series DC-DC Converter EMC: Immunity Test Level Criteria ESD EN61000-4-2 ±8 kV air discharge, ±6 kV contact A Radiated EN61000-4-3 10 V/m A EFT/Burst EN61000-4-4 ±2 kV A With external capacitor, suggested part is CHEMI-CON KY 330µF/100V Surge EN61000-4-5 ±1 kV A With external capacitor, suggested part is CHEMI-CON KY 330µF/100V Conducted EN61000-4-6 10 V rms A Phenomenon Standard Notes & Conditions Safety Approvals Safety Agency Safety Standard CB Report IEC60950-1 Notes & Conditions Information Technology UL UL/cUL60950-1 Information Technology Mechanical Details Optional Heatsink (-HK) 1.00 (25.4) 0.40 (10.16) 0.40 (10.16) 4 0.80 (20.3) Bottom View 1 2 0.20 (5.08) 0.24 (6.0) 0.40 ±0.02 (10.16 ±0.5) 5 1.00 (25.4) 3 0.64 (16.3) Max. 0.10 (2.54) 0.69 (17.46) Max. ø 0.04 (1.00) 1.22 (31.0) Max. 0.77 (19.50) Max. Heat-Sink 6 0.30 (7.62) Thermal Pad Clamp Converter 0.10 (2.54) Pin Connections Pin 1 2 3 4 5 6 Notes 1. All dimensions are in inches (mm) 2. Weight: 0.03 lbs (15.0g) approx. 3. Tolerance: X.XX±0.01 (X.X±0.25) X.XXX±0.005 (X.XX±0.13) 4. Pin Tolerance: ±0.002 (±0.05) Application Notes Single Dual +Vin +Vin -Vin -Vin +Vout +Vout No Pin Common -Vout -Vout Optional Remote On/Off Optional Remote On/Off Derating Curve Output Power (%) 100 With optional heatsink (-HK) 0 -40 60 70 100 Ambient Temperature (°C) 3 www.xppower.com 09 Feb 16