MC79L00A Series 100 mA Negative Voltage Regulators The MC79L00A Series negative voltage regulators are inexpensive, easy−to−use devices suitable for numerous applications requiring up to 100 mA. Like the higher powered MC7900 Series negative regulators, this series features thermal shutdown and current limiting, making them remarkably rugged. In most applications, no external components are required for operation. The MC79L00A devices are useful for on−card regulation or any other application where a regulated negative voltage at a modest current level is needed. These regulators offer substantial advantage over the common resistor/Zener diode approach. http://onsemi.com THREE−TERMINAL LOW CURRENT NEGATIVE FIXED VOLTAGE REGULATORS MARKING DIAGRAMS Features • • • • • • No External Components Required Internal Short Circuit Current Limiting Internal Thermal Overload Protection Low Cost Complementary Positive Regulators Offered (MC78L00 Series) Pb−Free Packages are Available GND R1 R 5 R18 R8 R6 Q10 Q5 R9 R17 Q4 Q14 Q9 Q1 1 SOIC−8 D SUFFIX CASE 751 12 1 3 STRAIGHT LEAD BULK PACK Vout Vin Vin NC GND Vin Vin NC R16 R4 8 9Lxxx ALYWx G 1 TO−92 P SUFFIX CASE 29 2 3 BENT LEAD TAPE & REEL AMMO PACK Pin 1. Ground 2. Input 3. Output R7 Q8 8 Pin 1. 2. 3. 4. 5. 6. 7. 8. MC79L xxxxx ALYWWG G Output Q12 R2 Z1 R3 C Q7 Q6 R10 Q13 Q2 R11 Q11 R14 R15 Input *Automotive temperature range selections are available with special test conditions and additional tests in 5, 12 and 15 V devices. Contact your local ON Semiconductor sales office for information. Figure 1. Representative Schematic Diagram xxx = Specific Device Code A = Assembly Location L = Wafer Lot Y = Year W, WW = Work Week y = B or C G = Pb−Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. © Semiconductor Components Industries, LLC, 2008 May, 2008 − Rev. 9 1 Publication Order Number: MC79L00/D MC79L00A Series MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.) Symbol Value Unit VI −30 −35 −40 Vdc Power Dissipation Case 29 (TO−92 Type) TA = 25°C Thermal Resistance, Junction−to−Ambient Thermal Resistance, Junction−to−Case PD RqJA RqJC Internally Limited 160 83 W °C/W °C/W Case 751 (SOIC−8 Type) (Note 1) TA = 25°C Thermal Resistance, Junction−to−Ambient Thermal Resistance, Junction−to−Case PD RqJA RqJC Internally Limited 180 45 W °C/W °C/W Tstg −65 to +150 °C TJ +150 °C Rating Input Voltage (−5 V) (−12, −15, −18 V) (−24 V) Storage Temperature Range Junction Temperature Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. SOIC−8 Junction−to−Ambient Thermal Resistance is for minimum recommended pad size. Refer to Figure 9 for Thermal Resistance variation versus pad size. *This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL_STD_883, Method 3015 Machine Model Method 200 V. ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ +125°C (for MC79LXXAB), 0°C < TJ < +125°C (for MC79LXXAC)). MC79L05AC, AB Characteristics Symbol Min Typ Max Unit VO −4.8 −5.0 −5.2 Vdc − − − − 150 100 − − − − 60 30 −4.75 −4.75 − − −5.25 −5.25 − − − − 6.0 5.5 − − − − 1.5 0.1 Output Voltage (TJ = +25°C) Input Regulation (TJ = +25°C) −7.0 Vdc ≥ VI ≥ −20 Vdc −8.0 Vdc ≥ VI ≥ −20 Vdc Regline Load Regulation TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA 1.0 mA ≤ IO ≤ 40 mA Regload mV mV Output Voltage −7.0 Vdc ≥ VI ≥ −20 Vdc, 1.0 mA ≤ IO ≤ 40 mA VI = −10 Vdc, 1.0 mA ≤ IO ≤ 70 mA VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change −8.0 Vdc ≥ VI ≥ −20 Vdc 1.0 mA ≤ IO ≤ 40 mA IIB Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 40 − mV Ripple Rejection (−8.0 ≥ VI ≥ −18 Vdc, f = 120 Hz, TJ = +25°C) RR 41 49 − dB |VI−VO| − 1.7 − Vdc Dropout Voltage (IO = 40 mA, TJ = +25°C) http://onsemi.com 2 Vdc mA mA MC79L00A Series ELECTRICAL CHARACTERISTICS (VI = −19 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ +125°C (for MC79LXXAB), 0°C < TJ < +125°C (for MC79LXXAC)). MC79L12AC, AB Characteristics Symbol Min Typ Max Unit VO −11.5 −12 −12.5 Vdc − − − − 250 200 − − − − Output Voltage (TJ = +25°C) Input Regulation (TJ = +25°C) −14.5 Vdc ≥ VI ≥ −27 Vdc −16 Vdc ≥ VI ≥ −27 Vdc Regline Load Regulation TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA 1.0 mA ≤ IO ≤ 40 mA Regload Output Voltage −14.5 Vdc ≥ VI ≥ −27 Vdc, 1.0 mA ≤ IO ≤ 40 mA VI = −19 Vdc, 1.0 mA ≤ IO ≤ 70 mA VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change −16 Vdc ≥ VI ≥ −27 Vdc 1.0 mA ≤ IO ≤ 40 mA IIB Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Ripple Rejection (−15 ≤ VI ≤ −25 Vdc, f = 120 Hz, TJ = +25°C) Dropout Voltage (IO = 40 mA, TJ = +25°C) −11.4 −11.4 − − − − − − − − − − Vn − RR |VI−VO| mV 100 50 mV −12.6 −12.6 Vdc 6.5 6.0 mA 1.5 0.2 mA 80 − mV 37 42 − dB − 1.7 − Vdc ELECTRICAL CHARACTERISTICS (VI = −23 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ +125°C (for MC79LXXAB), 0°C < TJ < +125°C (for MC79LXXAC)). MC79L15AC, AB Characteristics Symbol Min Typ Max Unit VO −14.4 −15 −15.6 Vdc − − − − 300 250 − − − − 150 75 −14.25 −14.25 − − −15.75 −15.75 − − − − 6.5 6.0 − − − − 1.5 0.1 Output Voltage (TJ = +25°C) Input Regulation (TJ = +25°C) −17.5 Vdc ≥ VI ≥ −30 Vdc −20 Vdc ≥ VI ≥ −30 Vdc Regline Load Regulation TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA 1.0 mA ≤ IO ≤ 40 mA Regload Output Voltage −17.5 Vdc ≥ VI ≥ −Vdc, 1.0 mA ≤ IO ≤ 40 mA VI = −23 Vdc, 1.0 mA ≤ IO ≤ 70 mA VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB mV mV Vdc mA Input Bias Current Change −20 Vdc ≥ VI ≥ −30 Vdc 1.0 mA ≤ IO ≤ 40 mA DIIB Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) VN − 90 − mV Ripple Rejection (−18.5 ≤ VI ≤ −28.5 Vdc, f = 120 Hz) RR 34 39 − dB |VI−VO| − 1.7 − Vdc Dropout Voltage IO = 40 mA, TJ = +25°C http://onsemi.com 3 mA MC79L00A Series ELECTRICAL CHARACTERISTICS (VI = −27 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ +125°C (for MC79LXXAB), 0°C < TJ < +125°C (for MC79LXXAC), unless otherwise noted). MC79L18AC Characteristics Symbol Min Typ Max Unit VO −17.3 −18 −18.7 Vdc − − − − − − − − 325 − − 275 − − − − 170 85 −17.1 − −17.1 − − − −18.9 − −18.9 − − − − 6.5 6.0 − − − − − − 1.5 − 0.1 Output Voltage (TJ = +25°C) Input Regulation (TJ = +25°C) −20.7 Vdc ≥ VI ≥ −33 Vdc −21.4 Vdc ≥ VI ≥ −33 Vdc −22 Vdc ≥ VI ≥ −33 Vdc −21 Vdc ≥ VI ≥ −33 Vdc Regline Load Regulation TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA 1.0 mA ≤ IO ≤ 40 mA Regload mV mV Output Voltage −20.7 Vdc ≥ VI ≥ −33 Vdc, 1.0 mA ≤ IO ≤ 40 mA −21.4 Vdc ≥ VI ≥ −33 Vdc, 1.0 mA ≤ IO ≤ 40 mA VI = −27 Vdc, 1.0 mA ≤ IO ≤ 70 mA VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change −21 Vdc ≥ VI ≥ −33 Vdc −27 Vdc ≥ VI ≥ −33 Vdc 1.0 mA ≤ IO ≤ 40 mA IIB Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 150 − mV Ripple Rejection (−23 ≤ VI ≤ −33 Vdc, f = 120 Hz, TJ = +25°C) RR 33 48 − dB |VI−VO| − 1.7 − Vdc Dropout Voltage IO = 40 mA, TJ = +25°C Vdc mA mA ELECTRICAL CHARACTERISTICS (VI = −33 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ +125°C (for MC79LXXAB), 0°C < TJ < +125°C (for MC79LXXAC), unless otherwise noted). MC79L24AC Characteristics Symbol Min Typ Max Unit VO −23 −24 −25 Vdc − − − − − − 350 − 300 − − − − 200 100 −22.8 − −22.8 − − − −25.2 − −25.2 − − − − 6.5 6.0 − − − − 1.5 0.1 Vn − 200 − RR 31 47 − dB |VI−VO| − 1.7 − Vdc Output Voltage (TJ = +25°C) Input Regulation (TJ = +25°C) −27 Vdc ≥ VI ≥ −38 Vdc −27.5 Vdc ≥ VI ≥ −38 Vdc −28 Vdc ≥ VI ≥ −38 Vdc Regline Load Regulation TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA 1.0 mA ≤ IO ≤ 40 mA Regload Output Voltage −27 Vdc ≥ VI ≥ −38 V, 1.0 mA ≤ IO ≤ 40 mA −28 Vdc ≥ VI ≥ −38 Vdc, 1.0 mA ≤ IO ≤ 40 mA VI = −33 Vdc, 1.0 mA ≤ IO ≤ 70 mA VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB Input Bias Current Change −28 Vdc ≥ VI ≥ −38 Vdc 1.0 mA ≤ IO ≤ 40 mA DIIB Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Ripple Rejection (−29 ≤ VI ≤ −35 Vdc, f = 120 Hz, TJ = +25°C) Dropout Voltage IO = 40 mA, TJ = +25°C http://onsemi.com 4 mV mV Vdc mA mA mV MC79L00A Series APPLICATIONS INFORMATION Design Considerations high−frequency characteristics to insure stable operation under all load conditions. A 0.33 mF or larger tantalum, mylar, or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulator’s input terminals. Normally good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. Bypassing the output is also recommended. The MC79L00A Series of fixed voltage regulators are designed with Thermal Overload Protections that shuts down the circuit when subjected to an excessive power overload condition, Internal Short Circuit Protection that limits the maximum current the circuit will pass. In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire length, or if the output load capacitance is large. An input bypass capacitor should be selected to provide good Input +Vin MC78LXX +VO CI* 0.33mF 0.1mF 0.33mF MC79LXX Output CO** 0.1mF 0.1mF -Vin MC79LXX A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above the output voltage even during the low point on the ripple voltage. -VO 0.33mF * CI is required if regulator is located an appreciable * distance from the power supply filter ** CO improves stability and transient response. Figure 2. Positive and Negative Regulator Figure 3. Standard Application http://onsemi.com 5 MC79L00A Series TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted.) MC79L05C VO = -5.0 V TJ = 25°C 6.0 IO = 1.0 mA 4.0 IO = 100 mA 2.0 IO = 40 mA 0 0 -2.0 -4.0 -6.0 Vin, INPUT VOLTAGE (V) -0.8 -2.5 V I -V O , INPUT/OUTPUT DIFFERENTIAL VOLTAGE (V) -2.0 IO = 70 mA IO = 40 mA -1.5 IO = 1.0 mA -1.0 Dropout of Regulation is defined when DVO = 2% of VO -0.5 0 -10 0 25 Figure 4. Dropout Characteristics I IB , INPUT BIAS CURRENT (mA) 5.0 4.0 3.8 3.6 3.4 MC79L05C Vin = -10 V VO = -5.0 V IO = 40 mA 3.2 3.0 0 0 25 50 75 100 TA, AMBIENT TEMPERATURE (°C) 4.0 3.0 2.0 1.0 0 125 MC79L05C VO = -5.0 V IO = 40 mA 0 -5.0 Figure 6. Input Bias Current versus Ambient Temperature -10 -15 -20 -25 -30 Vin, INPUT VOLTAGE (V) -35 170 3.2 RθJA , THERMAL RESISTANCE JUNCTION-TO-AIR (°C/W) 150 2.8 PD(max) for TA = +50°C 130 1,000 No Heatsink 100 RqJA = 200°C/W PD(max) to 25°C = 625 mW 10 25 50 75 100 125 TA, AMBIENT TEMPERATURE (°C) -40 Figure 7. Input Bias Current versus Input Voltage 10,000 P D , POWER DISSIPATION (mW) 125 Figure 5. Dropout Voltage versus Junction Temperature 4.2 I IB , INPUT BIAS CURRENT (mA) 50 75 100 TJ, JUNCTION TEMPERATURE (°C) 2.4 ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ 110 Graph represents symmetrical layout 90 L 70 L 1.6 1.2 3.0 mm 50 0.8 RqJA 30 0 150 2.0 oz. Copper 2.0 10 20 30 L, LENGTH OF COPPER (mm) 40 0.4 50 Figure 9. SOP−8 Thermal Resistance and Maximum Power Dissipation versus P.C.B. Copper Length Figure 8. Maximum Average Power Dissipation versus Ambient Temperature (TO−92) http://onsemi.com 6 PD, MAXIMUM POWER DISSIPATION (W) VO, OUTPUT VOLTAGE (V) 8.0 MC79L00A Series ORDERING INFORMATION Device MC79L05ABD Nominal Voltage Operating Temperature Range Package Shipping† −5.0 V TJ = −40° to +125°C SOIC−8 98 Units / Rail MC79L05ABDG SOIC−8 (Pb−Free) 98 Units / Rail MC79L05ABDR2 SOIC−8 2500 / Tape & Reel SOIC−8 (Pb−Free) 2500 / Tape & Reel TO−92 2000 Units / Bag TO−92 (Pb−Free) 2000 Units / Bag TO−92 2000 / Tape & Reel TO−92 (Pb−Free) 2000 / Tape & Reel SOIC−8 98 Units / Rail MC79L05ACDG SOIC−8 (Pb−Free) 98 Units / Rail MC79L05ACDR2 SOIC−8 2500 / Tape & Reel SOIC−8 (Pb−Free) 2500 / Tape & Reel TO−92 2000 Units / Bag TO−92 (Pb−Free) 2000 Units / Bag TO−92 2000 / Tape & Reel TO−92 (Pb−Free) 2000 / Tape & Reel TO−92 2000 / Tape & Ammo Box TO−92 (Pb−Free) 2000 / Tape & Ammo Box TO−92 2000 / Tape & Ammo Box TO−92 (Pb−Free) 2000 / Tape & Ammo Box MC79L05ABDR2G MC79L05ABP MC79L05ABPG MC79L05ABPRA MC79L05ABPRAG MC79L05ACD TJ = 0° to +125°C MC79L05ACDR2G MC79L05ACP MC79L05ACPG MC79L05ACPRA MC79L05ACPRAG MC79L05ACPRM MC79L05ACPRMG MC79L05ACPRP MC79L05ACPRPG MC79L12ABD SOIC−8 98 Units / Rail MC79L12ABDG −12 V TJ = −40° to +125°C SOIC−8 (Pb−Free) 98 Units / Rail MC79L12ABDR2 SOIC−8 2500 / Tape & Reel SOIC−8 (Pb−Free) 2500 / Tape & Reel TO−92 2000 Units / Bag TO−92 (Pb−Free) 2000 Units / Bag TO−92 2000 / Tape & Reel TO−92 (Pb−Free) 2000 / Tape & Reel MC79L12ABDR2G MC79L12ABP MC79L12ABPG MC79L12ABPRA MC79L12ABPRAG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 7 MC79L00A Series ORDERING INFORMATION Device MC79L12ACD Nominal Voltage Operating Temperature Range Package Shipping† −12 V TJ = 0° to +125°C SOIC−8 98 Units / Rail MC79L12ACDG SOIC−8 (Pb−Free) 98 Units / Rail MC79L12ACDR2 SOIC−8 2500 / Tape & Reel SOIC−8 (Pb−Free) 2500 / Tape & Reel TO−92 2000 Units / Bag TO−92 (Pb−Free) 2000 Units / Bag TO−92 2000 / Tape & Reel TO−92 (Pb−Free) 2000 / Tape & Reel TO−92 2000 / Tape & Ammo Box TO−92 (Pb−Free) 2000 / Tape & Ammo Box MC79L12ACDR2G MC79L12ACP MC79L12ACPG MC79L12ACPRA MC79L12ACPRAG MC79L12ACPRP MC79L12ACPRPG MC79L15ABD SOIC−8 98 Units / Rail MC79L15ABDG −15 V TJ = −40° to +125°C SOIC−8 (Pb−Free) 98 Units / Rail MC79L15ABDR2 SOIC−8 2500 / Tape & Reel SOIC−8 (Pb−Free) 2500 / Tape & Reel TO−92 2000 Units / Bag TO−92 (Pb−Free) 2000 Units / Bag TO−92 2000 / Tape & Ammo Box TO−92 (Pb−Free) 2000 / Tape & Ammo Box SOIC−8 98 Units / Rail MC79L15ACDG SOIC−8 (Pb−Free) 98 Units / Rail MC79L15ACDR2 SOIC−8 2500 / Tape & Reel SOIC−8 (Pb−Free) 2500 / Tape & Reel TO−92 2000 Units / Bag TO−92 (Pb−Free) 2000 Units / Bag TO−92 2000 / Tape & Reel TO−92 (Pb−Free) 2000 / Tape & Reel TO−92 2000 / Tape & Reel TO−92 (Pb−Free) 2000 / Tape & Reel TO−92 2000 / Tape & Ammo Box TO−92 (Pb−Free) 2000 / Tape & Ammo Box MC79L15ABDR2G MC79L15ABP MC79L15ABPG MC79L15ABPRP MC79L15ABPRPG MC79L15ACD TJ = 0° to +125°C MC79L15ACDR2G MC79L15ACP MC79L15ACPG MC79L15ACPRA MC79L15ACPRAG MC79L15ACPRE MC79L15ACPREG MC79L15ACPRP MC79L15ACPRPG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 8 MC79L00A Series ORDERING INFORMATION Device MC79L18ABPRP Nominal Voltage Operating Temperature Range Package Shipping† −18 V TJ = −40° to +125°C TO−92 2000 / Tape & Ammo Box TO−92 (Pb−Free) 2000 / Tape & Ammo Box TO−92 2000 Units / Bag TO−92 (Pb−Free) 2000 Units / Bag TO−92 2000 Units / Bag TO−92 (Pb−Free) 2000 Units / Bag TO−92 2000 Units / Bag TO−92 (Pb−Free) 2000 Units / Bag TO−92 2000 / Tape & Ammo Box TO−92 (Pb−Free) 2000 / Tape & Ammo Box TO−92 2000 / Tape & Ammo Box TO−92 (Pb−Free) 2000 / Tape & Ammo Box MC79L18ABPRPG MC79L18ACP TJ = 0° to +125°C MC79L18ACPG MC79L24ABP −24 V TJ = −40° to +125°C MC79L24ABPG MC79L24ACP TJ = 0° to +125°C MC79L24ACPG MC79L24ACPRM MC79L24ACPRMG MC79L24ACPRP MC79L24ACPRPG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 9 MC79L00A Series PACKAGE DIMENSIONS SOIC−8 CASE 751−07 ISSUE AJ −X− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A 8 5 S B 0.25 (0.010) M Y M 1 4 −Y− K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 10 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0 _ 8 _ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC79L00A Series PACKAGE DIMENSIONS TO−92 (TO−226) CASE 29−11 ISSUE AM A B STRAIGHT LEAD BULK PACK R P L SEATING PLANE K D X X G J H V C SECTION X−X N 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. DIM A B C D G H J K L N P R V INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.021 0.045 0.055 0.095 0.105 0.015 0.020 0.500 --0.250 --0.080 0.105 --0.100 0.115 --0.135 --- MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.407 0.533 1.15 1.39 2.42 2.66 0.39 0.50 12.70 --6.35 --2.04 2.66 --2.54 2.93 --3.43 --- N A R BENT LEAD TAPE & REEL AMMO PACK B P T SEATING PLANE G K D X X J V 1 C N SECTION X−X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. MILLIMETERS DIM MIN MAX A 4.45 5.20 B 4.32 5.33 C 3.18 4.19 D 0.40 0.54 G 2.40 2.80 J 0.39 0.50 K 12.70 --N 2.04 2.66 P 1.50 4.00 R 2.93 --V 3.43 --- ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your loca Sales Representative MC79L00/D