Preliminary Data Sheet NESG3033M14 R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 NPN SiGe RF Transistor for Low Noise, High-Gain Amplification 4-Pin Lead-Less Minimold (M14, 1208 PKG) FEATURES • The NESG3033M14 is an ideal choice for low noise, high-gain amplification NF = 0.6 dB TYP. @ VCE = 2 V, IC = 6 mA, f = 2.0 GHz • Maximum stable power gain: MSG = 20.5 dB TYP. @ VCE = 2 V, IC = 15 mA, f = 2.0 GHz • SiGe HBT technology (UHS3) adopted: fmax = 110 GHz • This product is improvement of ESD of NESG3032M14. • 4-pin lead-less minimold (M14, 1208 PKG) <R> ORDERING INFORMATION Part Number Order Number NESG3033M14 NESG3033M14-A Package Quantity 4-pin lead-less minimold 50 pcs • 8 mm wide embossed taping (M14, 1208 PKG) (Non reel) • Pin 1 (Collector), Pin 4 (NC) face the (Pb-Free) NESG3033M14-T3 NESG3033M14-T3-A Supplying Form perforation side of the tape 10 kpcs/reel Remark To order evaluation samples, please contact your nearby sales office. Unit sample quantity is 50 pcs. ABSOLUTE MAXIMUM RATINGS (TA = +25°C) Parameter Collector to Base Voltage Collector to Emitter Voltage Symbol VCBO Note 1 Unit 5.0 V 4.3 V Note 1 12 mA Collector Current IC 35 mA Total Power Dissipation Note 2 150 mW Base Current VCEO Ratings IB Ptot Junction Temperature Tj 150 °C Storage Temperature Tstg −65 to +150 °C Notes 1. VCBO and IB are limited by the permissible current of the protection element. 2. Mounted on 1.08 cm2 × 1.0 mm (t) glass epoxy PWB CAUTION Observe precautions when handling because these devices are sensitive to electrostatic discharge. The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field. R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 1 of 14 NESG3033M14 RECOMMENDED OPERATING RANGE (TA = +25°C) Parameter Symbol MIN. TYP. MAX. Unit Input Power Pin − − 0 dBm Base Feedback Resister Rb − − 100 kΩ Remark When the voltage return bias circuit like the figure below is used, a current increase is seen because the ESD protection element is turned on when recommended range of motion in the above table is exceeded. However, there is no influence of reliability, including deterioration. Rb Bias Choke R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 2 of 14 NESG3033M14 <R> ELECTRICAL CHARACTERISTICS (TA = +25°C) Parameter Symbol Test Conditions MIN. TYP. MAX. Unit DC Characteristics Collector Cut-off Current ICBO VCB = 5 V, IE = 0 − − 100 nA Emitter Cut-off Current IEBO VEB = 1 V, IC = 0 − − 100 nA VCE = 2 V, IC = 6 mA 220 300 380 − ⏐S21e⏐ VCE = 2 V, IC = 15 mA, f = 2.0 GHz 15.0 17.5 − dB Noise Figure NF VCE = 2 V, IC = 6 mA, f = 2.0 GHz, ZS = ZSopt, ZL = ZLopt − 0.60 0.85 dB Associated Gain Ga VCE = 2 V, IC = 6 mA, f = 2.0 GHz, ZS = ZSopt, ZL = ZLopt − 17.5 − dB VCB = 2 V, IE = 0, f = 1 MHz − 0.15 0.25 pF DC Current Gain hFE Note 1 RF Characteristics 2 Insertion Power Gain Reverse Transfer Capacitance Maximum Stable Power Gain Cre Note 2 MSG Note 3 VCE = 2 V, IC = 15 mA, f = 2.0 GHz Gain 1 dB Compression Output Power PO (1 dB) VCE = 3 V, IC (set) = 20 mA, f = 2.0 GHz, ZS = ZSopt, ZL = ZLopt 3rd Order Intermodulation Distortion Output Intercept Point OIP3 VCE = 3 V, IC (set) = 20 mA, f = 2.0 GHz, ZS = ZSopt, ZL = ZLopt 17.5 20.5 − dB − 12.5 − dBm − 24.0 − dBm Notes 1. Pulse measurement: PW ≤ 350 μs, Duty Cycle ≤ 2% 2. Collector to base capacitance when the emitter grounded 3. MSG = <R> S21 S12 hFE CLASSIFICATION Rank FB/YFB Marking zL hFE Value 220 to 380 R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 3 of 14 NESG3033M14 TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified) TOTAL POWER DISSIPATION vs. AMBIENT TEMPERATURE REVERSE TRANSFER CAPACITANCE vs. COLLECTOR TO BASE VOLTAGE Reverse Transfer Capacitance Cre (pF) Total Power Dissipation Ptot (mW) 250 Mounted on Glass Epoxy PCB (1.08 cm2 × 1.0 mm (t) ) 200 150 100 50 0 25 50 75 100 125 0.3 f = 1 MHz 0.2 0.1 0 150 1 COLLECTOR CURRENT vs. BASE TO EMITTER VOLTAGE Collector Current IC (mA) Collector Current IC (mA) 100 VCE = 1 V 1 0.1 0.01 0.001 0.5 0.6 0.7 0.8 0.9 1.0 0.1 0.01 0.001 0.0001 0.4 0.5 0.6 0.7 0.8 1.0 COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE 40 VCE = 3 V 200 μ A 35 10 1 0.1 0.01 0.001 30 180 μ A 160 μ A 140 μ A 25 120 μ A 20 100 μ A 80 μ A 15 60 μ A 10 40 μ A 5 0.5 0.9 Base to Emitter Voltage VBE (V) Collector Current IC (mA) Collector Current IC (mA) VCE = 2 V 1 COLLECTOR CURRENT vs. BASE TO EMITTER VOLTAGE 0.0001 0.4 5 10 Base to Emitter Voltage VBE (V) 100 4 COLLECTOR CURRENT vs. BASE TO EMITTER VOLTAGE 10 0.0001 0.4 3 Collector to Base Voltage VCB (V) Ambient Temperature TA (˚C) 100 2 0.6 0.7 0.8 0.9 1.0 Base to Emitter Voltage VBE (V) 0 IB = 20 μ A 1 2 3 4 5 Collector to Emitter Voltage VCE (V) Remark The graphs indicate nominal characteristics. R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 4 of 14 NESG3033M14 DC CURRENT GAIN vs. COLLECTOR CURRENT DC CURRENT GAIN vs. COLLECTOR CURRENT 1 000 1 000 100 10 0.1 VCE = 2 V DC Current Gain hFE DC Current Gain hFE VCE = 1 V 1 10 100 100 10 0.1 1 10 100 Collector Current IC (mA) Collector Current IC (mA) DC CURRENT GAIN vs. COLLECTOR CURRENT 1 000 DC Current Gain hFE VCE = 3 V 100 10 0.1 1 10 100 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 5 of 14 NESG3033M14 GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT 30 Gain Bandwidth Product fT (GHz) VCE = 1 V f = 2 GHz 25 20 15 10 5 0 1 10 20 15 10 5 10 100 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Gain Bandwidth Product fT (GHz) 10 5 10 100 INSERTION POWER GAIN, MAG, MSG vs. FREQUENCY 0 1 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) 15 GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT 25 40 VCE = 1 V IC = 15 mA 35 30 MSG MAG 25 20 15 MAG MSG |S21e|2 10 5 0 0.1 1 10 100 Collector Current IC (mA) Frequency f (GHz) INSERTION POWER GAIN, MAG, MSG vs. FREQUENCY INSERTION POWER GAIN, MAG, MSG vs. FREQUENCY 40 VCE = 2 V IC = 15 mA 35 MSG MAG 25 MAG 20 MSG |S21e|2 10 5 0 0.1 20 Collector Current IC (mA) VCE = 3 V f = 2 GHz 15 25 Collector Current IC (mA) 30 30 VCE = 2 V f = 2 GHz 0 1 100 1 10 100 Frequency f (GHz) Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Gain Bandwidth Product fT (GHz) 30 40 VCE = 3 V IC = 15 mA 35 30 MSG MAG 25 MAG 20 15 MSG |S21e|2 10 5 0 0.1 1 10 100 Frequency f (GHz) Remark The graphs indicate nominal characteristics. R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 6 of 14 NESG3033M14 INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT VCE = 1 V f = 0.5 GHz 25 MSG |S21e|2 20 15 10 5 0 1 10 100 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) 30 30 25 VCE = 1 V f = 1 GHz MSG MAG 20 |S21e|2 15 10 5 0 1 10 100 Collector Current IC (mA) INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT 30 25 VCE = 1 V f = 2 GHz MSG MAG 20 15 |S21e|2 10 5 0 25 20 1 10 100 30 25 VCE = 1 V f = 3 GHz MSG 20 MAG 15 |S21e|2 10 5 0 1 10 100 Collector Current IC (mA) Collector Current IC (mA) INSERTION POWER GAIN, MAG vs. COLLECTOR CURRENT INSERTION POWER GAIN, MSG vs. COLLECTOR CURRENT VCE = 1 V f = 5 GHz 15 MAG 10 |S21e|2 5 0 –5 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Collector Current IC (mA) 1 10 100 Collector Current IC (mA) Insertion Power Gain |S21e|2 (dB) Maximum Stable Power Gain MSG (dB) 2 Insertion Power Gain |S21e| (dB) Maximum Available Power Gain MAG (dB) Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Insertion Power Gain |S21e|2 (dB) Maximum Stable Power Gain MSG (dB) INSERTION POWER GAIN, MSG vs. COLLECTOR CURRENT 30 VCE = 2 V MSG f = 0.5 GHz 25 |S21e|2 20 15 10 5 0 1 10 100 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 7 of 14 NESG3033M14 25 VCE = 2 V f = 1 GHz MSG 2 |S21e| 20 15 10 5 0 1 10 100 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) 30 INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT 30 25 VCE = 2 V f = 2 GHz MSG MAG 20 |S21e|2 15 10 5 0 1 10 100 Collector Current IC (mA) INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT INSERTION POWER GAIN, MAG vs. COLLECTOR CURRENT 30 25 VCE = 2 V f = 3 GHz MSG MAG 20 15 2 |S21e| 10 5 0 30 25 1 10 100 25 VCE = 2 V f = 5 GHz 20 15 MAG 10 |S21e|2 5 0 1 10 100 Collector Current IC (mA) INSERTION POWER GAIN, MSG vs. COLLECTOR CURRENT INSERTION POWER GAIN, MSG vs. COLLECTOR CURRENT MSG 2 |S21e| 15 10 5 0 30 Collector Current IC (mA) VCE = 3 V f = 0.5 GHz 20 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Collector Current IC (mA) 1 10 100 Collector Current IC (mA) Insertion Power Gain |S21e|2 (dB) Maximum Stable Power Gain MSG (dB) 2 Insertion Power Gain |S21e| (dB) Maximum Stable Power Gain MSG (dB) Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Insertion Power Gain |S21e|2 (dB) Maximum Stable Power Gain MSG (dB) INSERTION POWER GAIN, MSG vs. COLLECTOR CURRENT 30 25 VCE = 3 V f = 1 GHz MSG 20 |S21e|2 15 10 5 0 1 10 100 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 8 of 14 NESG3033M14 INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT 30 25 VCE = 3 V f = 2 GHz MSG MAG 20 |S21e|2 15 10 5 0 1 10 100 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) Maximum Stable Power Gain MSG (dB) INSERTION POWER GAIN, MAG, MSG vs. COLLECTOR CURRENT 30 25 VCE = 3 V f = 3 GHz MSG 20 MAG 15 |S21e|2 10 5 0 1 10 100 Collector Current IC (mA) Collector Current IC (mA) 2 Insertion Power Gain |S21e| (dB) Maximum Available Power Gain MAG (dB) INSERTION POWER GAIN, MAG vs. COLLECTOR CURRENT 30 25 VCE = 3 V f = 5 GHz 20 15 MAG 10 |S21e|2 5 0 1 10 100 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 9 of 14 NESG3033M14 OUTPUT POWER, COLLECTOR CURRENT vs. INPUT POWER 20 50 40 15 Pout 30 10 5 20 IC 10 0 –5 –20 –15 –10 –5 Collector Current IC (mA) Output Power Pout (dBm) VCE = 3 V, f = 2 GHz Icq = 20 mA (RF OFF) 0 5 0 Input Power Pin (dBm) Measuring method : Measured at power matched with external sleeve tuner. (The load resistance is not inserted between the base DC power supply and Bias Tee.) NOISE FIGURE, ASSOCIATED GAIN vs. COLLECTOR CURRENT Noise Figure NF (dB) Ga 3 15 2 10 1 5 NF 0 1 Associated Gain Ga (dB) 20 4 VCE = 2 V f = 2 GHz 10 0 100 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. <R> S-PARAMETERS S-parameters and noise parameters are provided on our web site in a form (S2P) that enables direct import of the parameters to microwave circuit simulators without the need for keyboard inputs. Click here to download S-parameters. [Products] → [RF Devices] → [Device Parameters] URL http://www.renesas.com/products/microwave/ R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 10 of 14 NESG3033M14 EVALUATION CIRCUIT EXAMPLE (f = 1.575 GHz LNA) GND VCC IN R3 C3 C4 R1 C1 R2 L2 C2 L1 Tr. (NESG3033M14) NESG3033M14 GPS_LNA Notes 1. 15 × 24 mm, t = 0.2 mm double sided copper clad glass epoxy PWB. 2. Au plated on pattern 3. : Through holes R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 11 of 14 NESG3033M14 <R> EVALUATION CIRCUIT (f = 1.575 GHz LNA) VCC 3V C3 R1 C1 10 000 pF R3 62 Ω R2 5.6 Ω L2 3.9 nH C4 10 000 pF C2 82 kΩ OUT L1 6 pF IN 10 000 pF 5.6 nH Microstrip W = 0.15 mm L = 0.5 mm ×2 The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. <R> COMPONENT LIST Symbol Parts Part Number C1, C3, C4 Chip Capacitor GRM155B31H103KA88 Murata 10 000 pF C2 Chip Capacitor GRM1552C1H6R0DZ01 Murata 6 pF L1 Chip Inductor AML1005H5N6STS FDK 5.6 nH L2 Chip Inductor AML1005H3N9STS FDK 3.9 nH R1 Chip Resistor MCR01MZPJ823 ROHM 82 kΩ R2 Chip Resistor MCR01MZPJ5R6 ROHM 5.6 Ω R3 Chip Resistor MCR01MZPJ620 ROHM 62 Ω R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Maker Value Page 12 of 14 NESG3033M14 EXAMPLE OF CHARACTERISTICS FOR 1.575 GHz LNA EVALUATION BOARD ELECTRICAL CHARACTERISTICS (TA = +25°C, VCC = 3 V, IC = 6.1 mA, f = 1.575 GHz) Parameter Symbol Value Unit Noise Figure NF 0.72 dB Gain Ga 17.3 dB Input Return Loss RLin 10.3 dB Output Return Loss RLout 14.2 dB PO (1 dB) −0.3 dBm IIP3 0.7 dBm Gain 1 dB Compression Output Power Input 3rd Order Distortion Interception Point OUTPUT POWER, COLLECTOR CURRENT vs. INPUT POWER 15 25 VCC = 3 V, f = 1.575 GHz Icq = 6.1 mA (RF OFF) 10 20 5 15 Pout 0 10 IC –5 5 –10 –25 0 5 –20 –15 –10 –5 0 Collector Current IC (mA) Note Output Power POUT (dBm) 3rd Order Intermodulation Distortion IM3 (dBm) TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified) Output Power Pout (dBm) <R> OUTPUT POWER, IM3 vs. INPUT POWER 40 20 VCC = 3 V, IC = 6.1 mA f1in = 1.575 GHz, f2in = 1.576 GHz 0 POUT −20 −40 IM3 −60 IIP3 = 0.7 dBm −80 −30 Input Power Pin (dBm) −20 −10 0 10 Input Power Pin (dBm) Note A current increase is seen because the ESD protection element is turned on. However, there is no influence of deterioration etc. on reliability. Remark The graph indicates nominal characteristics. R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 13 of 14 NESG3033M14 PACKAGE DIMENSIONS 4-PIN LEAD-LESS MINIMOLD (M14, 1208 PKG) (UNIT: mm) 1.0±0.05 0.15±0.05 2 (Bottom View) 1 4 0.8 zL 3 0.8+0.07 –0.05 1.2+0.07 –0.05 0.2 0.11+0.1 –0.05 0.2 0.5±0.05 <R> PIN CONNECTIONS 1. 2. 3. 4. Collector Emitter Base Note NC (Connected with Pin 2) Note A NC pin is Non-connection in the mold package (When NC-pin is open state, It will get an influences of floating capacitance. Therefore, we recommend that NC pin connect to Emitter pin). R09DS0049EJ0300 Rev.3.00 Sep 14, 2012 Page 14 of 14 Revision History NESG3033M14 Data Sheet Description Rev. Date Page Summary 1.00 Jul 19, 2005 – First edition issued 2.00 Sep 11, 2007 – Second edition issued 3.00 Sep 14, 2012 Throughout The company name is changed to Renesas Electronics Corporation. p.1 Modification of ORDERING INFORMATION p.3 Modification of ELECTRICAL CHARACTERISTICS p.3 Modification of hFE CLASSIFICATION p.10 Modification of method for obtaining S-parameters p.12 Modification of EVALUTION CIRCUIT p.12 Modification of COMPONENT LIST p.13 Modification of EXAMPLE OF CHARACTERISTICS FOR f = 1.575 GHz LNA EVALUATION BOARD p.14 Modification of PACKAGE DIMENSIONS All trademarks and registered trademarks are the property of their respective owners. C-1 Notice 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics 3. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or 5. Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The recommended applications for each Renesas Electronics product depends on third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product. the product's quality grade, as indicated below. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics. 6. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products. 11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. California Eastern Laboratories, Inc. 4590 Patrick Henry Drive, Santa Clara, California 95054, U.S.A. Tel: +1-408-919-2500, Fax: +1-408-988-0279 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-651-700, Fax: +44-1628-651-804 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Düsseldorf, Germany Tel: +49-211-65030, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898 Renesas Electronics Hong Kong Limited Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2886-9318, Fax: +852 2886-9022/9044 Renesas Electronics Taiwan Co., Ltd. 13F, No. 363, Fu Shing North Road, Taipei, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre Singapore 339949 Tel: +65-6213-0200, Fax: +65-6213-0300 Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics Korea Co., Ltd. 11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea Tel: +82-2-558-3737, Fax: +82-2-558-5141 © 2012 Renesas Electronics Corporation. All rights reserved. [Colophon 2.2]