AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Fully Integrated, 8-Channel Ultrasound Analog Front End With Passive CW Mixer, and Digital I/Q Demodulator, 0.75 nV/rtHz, 14, 12-Bit, 65 MSPS, 158 mW/CH Check for Samples: AFE5809 FEATURES 1 • • • • • • • • • 8-Channel Complete Analog Front-End – LNA, VCAT, PGA, LPF, ADC, and CW Mixer Programmable Gain Low-Noise Amplifier (LNA) – 24, 18, 12 dB Gain – 0.25, 0.5, 1 VPP Linear Input Range – 0.63, 0.7, 0.9 nV/rtHz Input Referred Noise – Programmable Active Termination 40-dB Low Noise Voltage Controlled Attenuator (VCAT) 24/30-dB Programmable Gain Amplifier (PGA) 3rd Order Linear Phase Low-Pass Filter (LPF) – 10, 15, 20, 30 MHz 14-bit Analog-to-Digital Converter (ADC) – 77 dBFS SNR at 65 MSPS – LVDS Outputs Noise, Power Optimizations (Without Digital Demodulator) – 158 mW/CH at 0.75 nV/rtHz, 65 MSPS – 101 mW/CH at 1.1 nV/rtHz, 40 MSPS – 80 mW/CH at CW Mode Excellent Device-to-Device Gain Matching – ±0.5 dB (Typical) and ±1 dB (Max) Digital I/Q Demodulator after ADC – Wide Range Demodulation Frequency SPI IN 16X CLKP 16X CLKN • • • • • – < 1 kHz Frequency Resolution – Decimation Filter Factor M = 1 to 32 – 16xM tap FIR Decimation Filter – LVDS Rate Reduction after Demodulation – On-chip RAM With 32 Preset Profiles Low Harmonic Distortion Low Frequency Sonar Signal Processing Fast and Consistent Overload Recovery Passive Mixer for Continuous Wave Doppler(CWD) – Low Close-in Phase Noise –156 dBc/Hz at 1 kHz off 2.5 MHz Carrier – Phase Resolution of 1/16λ – Support 16X, 8X, 4X and 1X CW Clocks – 12dB Suppression on 3rd and 5th Harmonics – Flexible Input Clocks Small Package: 15 mm × 9 mm, 135-BGA APPLICATIONS • • • Medical Ultrasound Imaging Nondestructive Evaluation Equipments Sonar Applications AFE5809 with Demodulator 1 of 8 Channels SPI Logic VCAT LNA 0 to -40 dB 16 Phases Generator 1X CLK CW Mixer PGA 24, 30dB 3rd LP Filter 10, 15, 20, 30 MHz 14 Bit ADC Digital DeMod & LP Filter Summing Amplifier/ Filter Reference Reference Logic Control CW I/Q Vout Differential TGC Vcntl EXT/INT REFM/P DeMod Control LVDS LVDS Serializer OUT 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2012–2014, Texas Instruments Incorporated AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com DESCRIPTION The AFE5809 is a highly integrated analog front-end (AFE) solution specifically designed for ultrasound systems in which high performance and small size are required. The AFE5809 integrates a complete time-gain-control (TGC) imaging path and a continuous wave Doppler (CWD) path. It also enables users to select one of various power/noise combinations to optimize system performance. Therefore, the AFE5809 is a suitable ultrasound analog front end solution not only for high-end systems, but also for portable ones. The AFE5809 contains eight channels of voltage controlled amplifier (VCA), 14, and 12-bit Analog-to-Digital Converter (ADC), and CW mixer. The VCA includes Low noise Amplifier(LNA), Voltage controlled attenuator (VCAT), Programmable Gain Amplifier(PGA), and Low-Pass Filter (LPF). The LNA gain is programmable to support 250 mVPP to 1 VPP input signals. Programmable active termination is also supported by the LNA. The ultra-low noise VCAT provides an attenuation control range of 40 dB and improves overall low gain SNR which benefits harmonic imaging and near field imaging. The PGA provides gain options of 24 dB and 30 dB. Before the ADC, a LPF can be configured as 10, 15, 20, or 30 MHz to support ultrasound applications with different frequencies. In addition, the signal chain of the AFE5809 can handle signal frequency lower than 100 KHz, which enables the AFE5809 to be used in both sonar and medical applications. The high-performance 14 bit/65 MSPS ADC in the AFE5809 achieves 77 dBFS SNR. It ensures excellent SNR at low chain gain. The ADC’s LVDS outputs enable flexible system integration desired for miniaturized systems. The AFE5809 integrates a low power passive mixer and a low noise summing amplifier to accomplish on-chip CWD beamformer. 16 selectable phase-delays can be applied to each analog input signal. Meanwhile a unique 3rd and 5th order harmonic suppression filter is implemented to enhance CW sensitivity. AFE5809 also includes a digital in-phase and quadrature (I/Q) demodulator and a low-pass decimation filter. The main purpose of the demodulation block is to reduce the LVDS data rate and improve overall system power efficiency. The I/Q demodulator can accept ADC output with up to 65 MSPS sampling rate and 14 bit resolution. For example, after digital demodulation and 4× decimation filtering, the data rate for either in-phase or quadrature output is reduced to 16.25 MSPS and the data resolution is improved to 16bit consequently. Hence, the overall LVDS trace reduction can be a factor of 2. This demodulator can be bypassed and powered down completely if it is not needed. The AFE5809 is available in a 15-mm × 9-mm, 135-pin BGA package and it is specified for operation from 0°C to 85°C. NOTE AFE5809 with date code later than 2014, that is date code >41XXXX, has below additional features which can be enabled by Register 61[15,14,13]. Existing analog performance remains the same. • 61[13] enables an additional voltage clamp at the PGA's V2I input. This limits the amount of overload signal the PGA sees. • 61[14] enables a 1st order 5 MHz LPF filter to suppress signals > 5 MHz or high order harmonics. • 61[15] enables a –6-dB PGA clamp setting. The actual PGA output is less than ADC's full scale amplitude 2 Vpp. 2 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Channels 1, 2 -SIN COS C0 I ADC 1 DC Removal 14bit 40MHz Down Conversion I Q I Decimation Filter Q Samples RAM -SIN I DC Removal ADC 2 14bit 40MHz ADC 3 Cn Q LVDS 1 COS 14bit 40MHz ... Down Conversion Q C0 ... Serializer Cn I 640Mbps I Decimation Filter Q Q Channels 3, 4 LVDS 2 ADC 4 640Mbps 14bit 40MHz ADC 5 14bit 40MHz Channels 5, 6 LVDS 3 ADC 6 640Mbps 14bit 40MHz ADC 7 14bit 40MHz Channels 7, 8 LVDS 4 ADC 8 640Mbps 14bit 40MHz COS -SIN ... C0 COS & -SIN Table Cn Coefficient Memory Freq Regsiters Control Control Figure 1. Digital Demodulator Block Diagram Table 1. PACKAGING/ORDERING INFORMATION (1) (1) PRODUCT PACKAGE TYPE OPERATING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY AFE5809 ZCF 0°C to 85°C AFE5809ZCF Tray, 160 For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 3 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) Supply voltage range MIN MAX UNIT AVDD –0.3 3.9 V AVDD_ADC –0.3 2.2 V AVDD_5V –0.3 6 V DVDD –0.3 2.2 V DVDD_LDO –0.3 1.6 V Voltage between AVSS and LVSS –0.3 0.3 V Voltage at analog inputs and digital inputs –0.3 min [3.6, AVDD + 0.3] V 260 °C 105 °C 150 °C Peak solder temperature (2) Maximum junction temperature (TJ), any condition Storage temperature range –55 Operating temperature range ESD Ratings (1) (2) 0 Human Body Model (HBM) Charged Device Model (CDM) 85 °C 2000 V 500 V Stresses above those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied Exposure to absolute maximum rated conditions for extended periods may degrade device reliability. Device complies with JSTD-020D. THERMAL INFORMATION AFE5809 THERMAL METRIC (1) BGA UNIT 135 PINS θJA Junction-to-ambient thermal resistance θJCtop Junction-to-case (top) thermal resistance θJB Junction-to-board thermal resistance 11.5 ψJT Junction-to-top characterization parameter 0.2 ψJB Junction-to-board characterization parameter 10.8 θJCbot Junction-to-case (bottom) thermal resistance n/a (1) 34.1 5 °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. RECOMMENDED OPERATING CONDITIONS PARAMETER MIN MAX AVDD 3.15 3.6 V AVDD_ADC 1.7 1.9 V DVDD 1.7 1.9 V DVDD_LDO1/2 (Internal Generated) 1.2 1.4 V 4.75 5.5 V 0 85 °C AVDD_5V Ambient Temperature, TA 4 Submit Documentation Feedback UNIT Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 PINOUT INFORMATION Table 2. Top View ZCF (BGA-135) 1 2 3 4 5 6 7 8 9 A AVDD INP8 INP7 INP6 INP5 INP4 INP3 INP2 INP1 B CM_BYP ACT8 ACT7 ACT6 ACT5 ACT4 ACT3 ACT2 ACT1 C AVSS INM8 INM7 INM6 INM5 INM4 INM3 INM2 INM1 D AVSS AVSS AVSS AVSS AVSS AVSS AVSS AVDD AVDD E CW_IP_AMPINP CW_IP_AMPINM AVSS AVSS AVSS AVSS AVSS AVDD AVDD F CW_IP_OUTM CW_IP_OUTP AVSS AVSS AVSS AVSS AVSS CLKP_16X CLKM_16X G AVSS AVSS AVSS AVSS AVSS AVSS AVSS CLKP_1X CLKM_1X H CW_QP_OUTM CW_QP_OUTP AVSS AVSS AVSS AVSS AVSS PDN_GLOBAL RESET J CW_QP_AMPINP CW_QP_AMPINM AVSS AVSS AVSS AVDD_ADC AVDD_ADC PDN_VCA SCLK K AVDD AVDD_5V VCNTLP VCNTLM VHIGH AVSS DNC AVDD_ADC SDATA L CLKP_ADC CLKM_ADC AVDD_ADC REFM DNC LDO_EN TX_SYNC_IN PDN_ADC SEN M AVDD_ADC AVDD_ADC VREF_IN REFP DNC LDO_SETV SPI_DIG_EN DNC SDOUT N D8P D8M DVDD DVDD_LDO1 DVSS DVDD_LDO2 DVDD D1M D1P P D7M D6M D5M FCLKM DVSS DCLKM D4M D3M D2M R D7P D6P D5P FCLKP DVSS DCLKP D4P D3P D2P Table 3. PIN FUNCTIONS PIN DESCRIPTION NO. NAME B9 to B2 ACT1...ACT8 Active termination input pins for CH1 to 8 A1, D8, D9, E8, E9, K1 AVDD 3.3-V analog supply for LNA, VCAT, PGA, LPF, and CWD blocks K2 AVDD_5V 5-V analog supply for LNA, VCAT, PGA, LPF, and CWD blocks J6, J7, K8, L3, M1, M2 AVDD_ADC 1.8-V analog power supply for ADC C1, D1 to D7, E3 to E7, F3 to F7, G1 to G7, AVSS H3 to H7,J3 toJ5, K6 Analog ground L2 CLKM_ADC Negative input of differential ADC clock. In the single-end clock mode, it can be tied to GND directly or through a 0.1-µF capacitor. L1 CLKP_ADC Positive input of differential ADC clock. In the single-end clock mode, it can be tied to clock signal directly or through a 0.1-µF capacitor. F9 CLKM_16X Negative input of differential CW 16X clock. Tie to GND when the CMOS clock mode is enabled. In the 4X, and 8X CW clock modes, this pin becomes the 4X or 8X CLKM input. In the 1X CW clock mode, this pin becomes the in-phase 1X CLKM for the CW mixer. Can be floated if CW mode is not used. See register 0x36[11:10]. F8 CLKP_16X Positive input of differential CW 16X clock. In 4X, and 8X clock modes, this pin becomes the 4X, and 8X CLKP input. In the 1X CW clock mode, this pin becomes the in-phase 1X CLKP for the CW mixer. Can be floated if CW mode is not used. See register 0x36[11:10]. G9 CLKM_1X Negative input of differential CW 1X clock. Tie to GND when the CMOS clock mode is enabled (refer to Figure 105 for details). In the 1X clock mode, this pin is the quadrature-phase 1X CLKM for the CW mixer. Can be floated if CW mode is not used. G8 CLKP_1X Positive input of differential CW 1X clock. In the 1X clock mode, this pin is the quadrature-phase 1X CLKP for the CW mixer. Can be floated if CW mode is not used. B1 CM_BYP Bias voltage and bypass to ground. 1 µF is recommended. To suppress the ultra-low frequency noise, 10 µF can be used. E2 CW_IP_AMPINM Negative differential input of the in-phase summing amplifier. External LPF capacitor has to be connected between CW_IP_AMPINM and CW_IP_OUTP. This pin provides the current output for the CW mixer. This pin becomes the CH7 PGA negative output when PGA test mode is enabled. Can be floated if not used. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 5 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Table 3. PIN FUNCTIONS (continued) PIN DESCRIPTION NO. NAME E1 CW_IP_AMPINP Positive differential input of the in-phase summing amplifier. External LPF capacitor has to be connected between CW_IP_AMPINP and CW_IP_OUTM. This pin provides the current output for the CW mixer. This pin becomes the CH7 PGA positive output when PGA test mode is enabled. Can be floated if not used. F1 CW_IP_OUTM Negative differential output for the in-phase summing amplifier. External LPF capacitor has to be connected between CW_IP_AMPINP and CW_IP_OUTPM. Can be floated if not used. F2 CW_IP_OUTP Positive differential output for the in-phase summing amplifier. External LPF capacitor has to be connected between CW_IP_AMPINM and CW_IP_OUTP. Can be floated if not used. J2 CW_QP_AMPIN M Negative differential input of the quadrature-phase summing amplifier. External LPF capacitor has to be connected between CW_QP_AMPINM and CW_QP_OUTP. This pin provides the current output for the CW mixer. This pin becomes CH8 PGA negative output when PGA test mode is enabled. Can be floated if not used. J1 CW_QP_AMPINP Positive differential input of the quadrature-phase summing amplifier. External LPF capacitor has to be connected between CW_QP_AMPINP and CW_QP_OUTM. This pin provides the current output for the CW mixer. This pin becomes CH8 PGA positive output when PGA test mode is enabled. Can be floated if not used. H1 CW_QP_OUTM Negative differential output for the quadrature-phase summing amplifier. External LPF capacitor has to be connected between CW_QP_AMPINP and CW_QP_OUTM. Can be floated if not used. H2 CW_QP_OUTP Positive differential output for the quadrature-phase summing amplifier. External LPF capacitor has to be connected between CW_QP_AMPINM and CW_QP_OUTP. Can be floated if not used. N8, P9~P7, P3 D1M to D8M to P1, N2 ADC CH1 to 8 LVDS negative outputs N9, R9~R7, R3 to R1, N1 D1P to D8P ADC CH1 to 8 LVDS positive outputs P6 DCLKM LVDS bit clock (7x) negative output R6 DCLKP LVDS bit clock (7x) positive output N3, N7 DVDD ADC digital and I/O power supply, 1.8 V N5, P5, R5 DVSS ADC digital ground N4, N6 DVDD_LDO1, DVDD_LDO2 Demodulator digital power supply generated internally. These two pins should be separated on PCB and decoupled respectively with 0.1µF capacitors. P4 FCLKM LVDS frame clock (1X) negative output R4 FCLKP LVDS frame clock (1X) positive output C9 to C2 INM1…INM8 CH1 to 8 complimentary analog inputs. Bypass to ground with ≥ 0.015-µF capacitors. The HPF response of the LNA depends on the capacitors. A9 to A2 INP1...INP8 CH1 to 8 analog inputs. AC couple to inputs with ≥ 0.1-µF capacitors. L6 LDO_EN Must be tied to 1.8 V DVDD M6 LDO_SETV Must be tied to 1.8 V DVDD L8 PDN_ADC ADC partial (fast) power down control pin with an internal pull down resistor of 100 kΩ. Active High. Either 1.8-V or 3.3-V logic level can be used. J8 PDN_VCA VCA partial (fast) power down control pin with an internal pull down resistor of 20 kΩ. Active High. 3.3V logic level should be used. H8 PDN_GLOBAL Global (complete) power-down control pin for the entire chip with an internal pull down resistor of 20 kΩ. Active High. 3.3 V logic level should be used. L4 REFM 0.5 V reference output in the internal reference mode. Must leave floated in the internal reference mode. Adding a test point on the PCB is recommended for monitoring the reference output M4 REFP 1.5 V reference output in the internal reference mode. Must leave floated in the internal reference mode. Adding a test point on the PCB is recommended for monitoring the reference output H9 RESET Hardware reset pin with an internal pull-down resistor of 20 kΩ. Active high. 3.3 logic level can be used. J9 SCLK Serial interface clock input with an internal pull-down resistor of 20 kΩ. This pin is connected to both ADC and VCA. 3.3-V logic should be used. K9 SDATA Serial interface data input with an internal pull-down resistor of 20 kΩ. This pin is connected to both ADC and VCA. 3.3-V logic should be used. 6 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Table 3. PIN FUNCTIONS (continued) PIN DESCRIPTION NO. NAME M9 SDOUT Serial interface data readout. High impedance when readout is disabled. This pin is connected to ADC only. 1.8 V logic can be used. L9 SEN Serial interface enable with an internal pull up resistor of 20 kΩ. Active low. This pin is connected to both ADC and VCA. 3.3-V logic should be used. M7 SPI_DIG_EN Serial interface enable for the digital demodulator memory space. SPI_DIG_EN pin is required to be set to '0' during SPI transactions to demodulator registers. Each transaction starts by setting SEN as '0' and terminates by setting it back to '1' (similar to other register transactions). Pull up internally through a 20-kΩ resistor. This pin is connected to both ADC and VCA. 3.3-V logic should be used. L7 TX_SYNC_IN System trig signal input. It indicates the start of signal transmission. Either 3.3-V or 1.8-V logic level can be used. K4 VCNTLM Negative differential attenuation control pin. K3 VCNTLP Positive differential attenuation control pin K5 VHIGH Bias voltage; bypass to ground with ≥ 1 µF. M3 VREF_IN ADC 1.4-V reference input in the external reference mode; bypass to ground with 0.1µF. K7,L5, M5, M8 DNC Do not connect. Must leave floated Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 7 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com ELECTRICAL CHARACTERISTICS AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, AC-coupled with 0.1 µF at INP and bypassed to ground with 15 nF at INM, No active termination, VCNTL = 0 V, fIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14Bit, sample rate = 65MSPS, LPF Filter = 15 MHz, low noise mode, VOUT = –1 dBFS, Single-ended VCNTL mode, VCNTLM = GND, ADC configured in internal reference mode, internal 500 Ω CW feedback resistor, CMOS CW clocks, at ambient temperature TA = 25°C, Digital demodulator is disabled unless otherwise noted. Min and max values are specified across full-temperature range with AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V. PARAMETER TEST CONDITION MIN TYP MAX UNIT TGC FULL SIGNAL CHANNEL (LNA+VCAT+LPF+ADC) en (RTI) en (RTI) NF Input voltage noise over LNA gain (low noise mode) Rs = 0 Ω, f = 2 MHz, LNA = 24, 18, 12 dB, PGA = 24 dB 0.76, 0.83, 1.16 Rs = 0 Ω, f = 2 MHz, LNA = 24, 18, 12 dB, PGA = 30 dB 0.75, 0.86, 1.12 Input voltage noise over LNA gain (low power mode) Rs = 0 Ω, f = 2 MHz, LNA = 24, 18, 12 dB, PGA = 24 dB 1.1, 1.2, 1.45 Rs = 0 Ω, f = 2 MHz, LNA = 24, 18, 12 dB, PGA = 30 dB 1.1, 1.2, 1.45 Input voltage noise over LNA gain (medium power mode) Rs = 0 Ω, f = 2 MHz, LNA = 24, 18, 12 dB, PGA = 24 dB 1, 1.05, 1.25 Rs = 0 Ω, f = 2 MHz, LNA = 24, 18, 12 dB, PGA = 30 dB 0.95, 1, 1.2 Input voltage noise at low frequency f = 100 kHz, INM Cap = 1 µF, PGA integrator disabled Input referred current noise Low Noise Mode/Medium Power Mode/Low Power Mode Noise figure nV/rtHz nV/rtHz nV/rtHz 0.9 nV/rtHz 2.7, 2.1, 2 pA/rtHz Rs = 200 Ω, 200-Ω active termination, PGA = 24 dB, LNA = 12, 18, 24 dB 3.85, 2.4, 1.8 dB Rs = 100 Ω, 100-Ω active termination, PGA = 24 dB, LNA = 12, 18, 24 dB 5.3, 3.1, 2.3 dB NF Noise figure Rs = 500 Ω, 1 kΩ, no termination, Low NF mode is enabled (Reg53[9] = 1) 0.94, 1.08 dB NF Noise figure Rs = 50 Ω / 200 Ω, no termination, Low noise mode (Reg53[9] = 0) 2.35, 1.05 dB VMAX Maximum linear input voltage LNA gain = 24, 18, 12 dB 250, 500, 1000 VCLAMP Clamp voltage Reg52[10:9] = 0, LNA = 24, 18, 12 dB 350, 600, 1150 mVpp Low noise mode 24, 30 PGA gain dB Medium/Low power mode 24, 28.5 LNA = 24 dB, PGA = 30 dB, Low noise mode Total gain Ch-CH noise correlation factor without signal (1) 54 LNA = 24 dB, PGA = 30 dB, Med power mode 52.5 LNA = 24 dB, PGA = 30 dB, Low power mode 52.5 Summing of 8 channels 0 Full band (VCNTL = 0, 0.8) Ch-CH noise correlation factor with signal (1) 0.15, 0.17 1MHz band over carrier (VCNTL= 0, 0.8) 0.18, 0.75 VCNTL= 0.6 V (22-dB total channel gain) Signal to noise ratio (SNR) dB VCNTL= 0, LNA = 18 dB, PGA = 24 dB 68 70 59.3 63 VCNTL= 0, LNA = 24 dB, PGA = 24 dB dBFS 58 Narrow band SNR SNR over 2-MHz band around carrier at VCNTL = 0.6 V (22-dB total gain) Input common-mode voltage At INP and INM pins 75 77 dBFS 2.4 V 8 kΩ Input resistance Preset active termination enabled Input capacitance Input control voltage VCNTLP – VCNTLM Common-mode voltage VCNTLP and VCNTLM pF 1.5 V 0.75 V -40 dB Gain slope VCNTL= 0.1 V to 1.1V 35 dB/V Input resistance Between VCNTLP and VCNTLM 200 KΩ Input capacitance Between VCNTLP and VCNTLM 1 pF TGC response time VCNTL= 0-V to 1.5-V step function 1.5 10, 15, 20, 30 3rd order-low-pass filter Settling time for change in LNA gain Settling time for change in active termination setting µs MHz 14 µs 1 µs Noise correlation factor is defined as Nc / (Nu+Nc), where Nc is the correlated noise power in single channel; and Nu is the uncorrelated noise power in single channel. Its measurement follows the below equation, in which the SNR of single channel signal and the SNR of summed eight channel signal are measured. NC 10 8CH_SNR 10 10 = Nu + NC 8 Ω 20 0 Gain range (1) 50,100,200,400 1CH_SNR 1 x 1 - 56 7 10 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 ELECTRICAL CHARACTERISTICS (continued) AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, AC-coupled with 0.1 µF at INP and bypassed to ground with 15 nF at INM, No active termination, VCNTL = 0 V, fIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14Bit, sample rate = 65MSPS, LPF Filter = 15 MHz, low noise mode, VOUT = –1 dBFS, Single-ended VCNTL mode, VCNTLM = GND, ADC configured in internal reference mode, internal 500 Ω CW feedback resistor, CMOS CW clocks, at ambient temperature TA = 25°C, Digital demodulator is disabled unless otherwise noted. Min and max values are specified across full-temperature range with AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V. PARAMETER TEST CONDITION MIN TYP MAX UNIT AC ACCURACY LPF Bandwidth tolerance ±5% CH-CH group delay variation 2 to 15 MHz CH-CH Phase variation 15-MHz signal 0 V < VCNTL< 0.1 V (Dev-to-Dev) Gain matching 0.1 V < VCNTL< 1.1 V(Dev-to-Dev), TA = 25°C 0.1 V < VCNTL< 1.1 V (Dev-to-Dev), TA = 0°C and 85°C Channel-to-channel Output offset VCNTL= 0, PGA = 30 dB, LNA = 24 dB ns Degree ±0.5 –1 ±0.5 +1 dB 1.1 V < VCNTL< 1.5 V (Dev-to-Dev) Gain matching 2 11 ±0.5 –1.1 1.1 ±0.25 –75 dB 75 LSB AC PERFORMANCE HD2 HD3 THD Second-harmonic distortion Third-harmonic distortion Total harmonic distortion FIN = 2 MHz; VOUT = -1 dBFS –60 FIN = 5 MHz; VOUT = -1 dBFS –60 FIN = 5 MHz; VIN= 500 mVPP, VOUT = –1 dBFS, LNA = 18 dB, VCNTL= 0.88 V –55 FIN = 5 MHz; VIN = 250 mVPP, VOUT = –1 dBFS, LNA = 24 dB, VCNTL= 0.88 V –55 FIN = 2 MHz; VOUT = –1 dBFS –55 FIN = 5 MHz; VOUT = –1 dBFS –55 FIN = 5 MHz; VIN = 500 mVPP, VOUT = –1 dBFS, LNA = 18 dB, VCNTL = 0.88 V –55 FIN = 5 MHz; VIN = 250 mVPP, VOUT = –1dBFS, LNA = 2 4dB, VCNTL= 0.88 V –55 FIN = 2 MHz; VOUT = –1 dBFS –55 FIN = 5 MHz; VOUT = – 1dBFS –55 –60 IMD3 Intermodulation distortion f1 = 5 MHz at –1 dBFS, f2 = 5.01 MHz at –27 dBFS XTALK Cross-talk FIN = 5 MHz; VOUT= –1 dBFS Phase noise kHz off 5 MHz (VCNTL= 0 V) Input referred voltage noise Rs = 0 Ω, f = 2 MHz, Rin = High Z, Gain = 24, 18, 12 dB High-pass filter –3 dB Cut-off Frequency dBc dBc dBc dBc –65 dB –132 dBc/Hz 0.63, 0.70, 0.9 nV/rtHz 50, 100, 150, 200 KHz 4 Vpp LNA LNA linear output VCAT+ PGA VCAT input noise 0 dB, –40 dB Attenuation PGA input noise 24 dB, 30 dB –3 dB HPF cut-off Frequency 2, 10.5 nV/rtHz 1.75 nV/rtHz 80 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 KHz 9 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com ELECTRICAL CHARACTERISTICS (continued) AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, AC-coupled with 0.1 µF at INP and bypassed to ground with 15 nF at INM, No active termination, VCNTL = 0 V, fIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14Bit, sample rate = 65MSPS, LPF Filter = 15 MHz, low noise mode, VOUT = –1 dBFS, Single-ended VCNTL mode, VCNTLM = GND, ADC configured in internal reference mode, internal 500 Ω CW feedback resistor, CMOS CW clocks, at ambient temperature TA = 25°C, Digital demodulator is disabled unless otherwise noted. Min and max values are specified across full-temperature range with AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V. PARAMETER TEST CONDITION MIN TYP MAX UNIT CW DOPPLER en (RTI) en (RTO) en (RTI) en (RTO) NF 0.8 8 channel mixer, LNA = 24 dB, 62.5-Ω feedback resistor 0.33 1 channel mixer, LNA = 24 dB, 500-Ω feedback resistor 12 8 channel mixer, LNA = 24 dB, 62.5-Ω feedback resistor 5 1 channel mixer, LNA = 18 dB, 500-Ω feedback resistor 1.1 8 channel mixer, LNA = 18 dB, 62.5-Ω feedback resistor 0.5 1 channel mixer, LNA = 18 dB, 500-Ω feedback resistor 8.1 8 channel mixer, LNA = 18 dB, 62.5-Ω feedback resistor 4.0 Rs = 100 Ω, RIN = High Z, FIN = 2 MHz (LNA, I/Q mixer and summing amplifier/filter) 1.8 nV/rtHz Output voltage noise (CW) nV/rtHz Input voltage noise (CW) nV/rtHz Output voltage noise (CW) Noise figure fCW 1 channel mixer, LNA = 24 dB, 500-Ω feedback resistor Input voltage noise (CW) CW operation range (2) nV/rtHz CW signal carrier frequency 8 1X CLK (16X mode) CW clock frequency dB MHz 8 16X CLK(16X mode) 128 4X CLK(4X mode) AC coupled LVDS clock amplitude 0.7 CLKM_16X-CLKP_16X; CLKM_1X-CLKP_1X Vpp AC coupled LVPECL clock amplitude VCMOS 1.6 CLK duty cycle 1X and 16X CLKs Common-mode voltage Internal provided 35% CMOS input clock amplitude 4 CW mixer phase noise 1 kHz off 2-MHz carrier Input dynamic range FIN = 2 MHz, LNA = 24/18/12 dB IMD3 Intermodulation distortion V 5 4 DR 10 65% 2.5 CW mixer conversion loss (2) MHz 32 156 160, 164, 165 V dB dBc/Hz dBFS/Hz f1 = 5.00 MHz, f2 = 5.01 MHz, both tones at –8.5-dBm amplitude, 8 channels summed up in-phase, CW feedback resistor = 87 Ω –50 dBc f1 = 5 MHz, F2= 5.01 MHz, both tones at –8.5-dBm amplitude, Single channel case, CW feed back resistor = 500 Ω –60 dBc I/Q Channel gain matching 16X mode ±0.04 dB I/Q Channel phase matching 16X mode ±0.1 Degree I/Q Channel gain matching 4X mode ±0.04 dB I/Q Channel phase matching 4X mode ±0.1 Degree Image rejection ratio FIN = 2.01 MHz, 300 mV input amplitude, CW clock frequency = 2.00 MHz –50 dBc In the 16X operation mode, the CW operation range is limited to 8 MHz due to the 16X CLK. The maximum clock frequency for the 16X CLK is 128 MHz. In the 8X, 4X, and 1X modes, higher CW signal frequencies up to 15 MHz can be supported with small degradation in performance, see application information: CW clock selection Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 ELECTRICAL CHARACTERISTICS (continued) AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, AC-coupled with 0.1 µF at INP and bypassed to ground with 15 nF at INM, No active termination, VCNTL = 0 V, fIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14Bit, sample rate = 65MSPS, LPF Filter = 15 MHz, low noise mode, VOUT = –1 dBFS, Single-ended VCNTL mode, VCNTLM = GND, ADC configured in internal reference mode, internal 500 Ω CW feedback resistor, CMOS CW clocks, at ambient temperature TA = 25°C, Digital demodulator is disabled unless otherwise noted. Min and max values are specified across full-temperature range with AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V. PARAMETER TEST CONDITION MIN TYP MAX UNIT CW SUMMING AMPLIFIER VCMO Common-mode voltage Summing amplifier inputs/outputs 1.5 Summing amplifier output 100 Hz V 4 Vpp 2 nV/rtHz 1.2 nV/rtHz 1 nV/rtHz Input referred current noise 2.5 pA/rtHz Unit gain bandwidth 200 MHz 20 mApp Input referred voltage noise 1 kHz 2 kHz to 100 MHz Max output current Linear operation range ADC SPECIFICATIONS Sample rate SNR Signal-to-noise ratio 10 65 MSPS Idle channel SNR of ADC 14b 77 dBFS REFP 1.5 V REFM 0.5 V VREF_IN Voltage 1.4 V VREF_IN Current 50 µA 65MSPS at 14 bit 910 Internal reference mode External reference mode ADC input full-scale range LVDS Rate 2 Vpp Mbps POWER DISSIPATION AVDD voltage 3.15 3.3 3.6 V 1.7 1.8 1.9 V 4.75 5 5.5 V 1.7 1.8 1.9 V TGC low noise mode, 65 MSPS 158 190 TGC low noise mode, 40 MSPS 145 TGC medium power mode, 40 MSPS 114 AVDD_ADC voltage AVDD_5V voltage DVDD voltage Total power dissipation per channel mW/CH TGC low power mode, 40 MSPS 101.5 TGC low noise mode, no signal 202 TGC medium power mode, no signal 126 TGC low power mode, no signal 240 99 CW-mode, no signal 147 TGC low noise mode, 500 mVPP Input,1% duty cycle 210 TGC medium power mode, 500 mVPP Input, 1% duty cycle 133 TGC low power, 500 mVPP Input, 1% duty cycle 105 170 AVDD (3.3-V) current mA CW-mode, 500 mVPP Input 375 TGC mode no signal 25.5 CW mode no signal, 16X clock = 32 MHz 32 TGC mode, 500 mVpp Input,1% duty cycle 26 35 AVDD_5V current mA CW-mode, 500 mVpp Input 42.5 TGC low noise mode, no signal 99 TGC medium power mode, no signal 68 TGC low power mode, no signal 121 55.5 VCA power dissipation mW/CH TGC low noise mode, 500 mVPP input,1% duty cycle TGC medium power mode, 500 mVPP Input, 1% duty cycle TGC low power mode, 500 mVpp input,1% duty cycle CW power dissipation No signal, ADC shutdown CW Mode no signal, 16X clock = 32 MHz 102.5 71 59.5 80 mW/CH 500 mVPP input, ADC shutdown , 16X clock = 32 MHz 173 AVDD_ADC (1.8-V) current 65MSPS 187 205 mA DVDD (1.8-V) current 65 MSPS 77 110 mA Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 11 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com ELECTRICAL CHARACTERISTICS (continued) AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, AC-coupled with 0.1 µF at INP and bypassed to ground with 15 nF at INM, No active termination, VCNTL = 0 V, fIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14Bit, sample rate = 65MSPS, LPF Filter = 15 MHz, low noise mode, VOUT = –1 dBFS, Single-ended VCNTL mode, VCNTLM = GND, ADC configured in internal reference mode, internal 500 Ω CW feedback resistor, CMOS CW clocks, at ambient temperature TA = 25°C, Digital demodulator is disabled unless otherwise noted. Min and max values are specified across full-temperature range with AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V. PARAMETER ADC power dissipation/CH Power dissipation in power down mode TEST CONDITION MIN MAX 59 69 50 MSPS 51 40 MSPS 46 20 MSPS 35 PDN_VCA = High, PDN_ADC = High 25 Complete power-down PDN_Global = High 0.6 UNIT mW/CH mW/CH Power-down response time Time taken to enter power down 1 µs Power-up response time VCA power down 2 µs + 1% of PDN time µs ADC power down 1 Power supply modulation ratio, AVDD and AVDD_5V Power supply rejection ratio (3) TYP 65 MSPS Complete power down 2.5 ms FIN = 5 MHz, at 50 mVPP noise at 1 kHz on supply (3) –65 dBc FIN = 5 MHz, at 50 mVpp noise at 50 kHz on supply (3) –65 f = 10 kHz,VCNTL = 0 V (high gain), AVDD –40 dBc f = 10 kHz,VCNTL = 0 V (high gain), AVDD_5 V –55 dBc f = 10 kHz,VCNTL = 1 V (low gain), AVDD –50 dBc PSMR specification is with respect to carrier signal amplitude. DIGITAL DEMODULATOR ELECTRICAL CHARACTERISTICS AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, DVDD_LDO = 1.4 V (internal generated), 14Bit/65MSPS, 4X decimation factor, at ambient temperature TA = +25°C, unless otherwise noted. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Addtional Power Consumption on DVDD (1.8 V) 65 MSPS, 4X decimation factor 90 mW/CH Additonal Power Consumption on DVDD (1.8 V) 40 MSPS, 4X decimation factor 61 mW/CH Addtional Power Consumption on DVDD (1.8 V) 65 MSPS, 32X decimation factor, half LVDS pairs are powered down 77 mW/CH Additonal Power Consumption on DVDD (1.8 V) 40 MSPS, 32X decimation factor, half LVDS pairs are powered down 55 mW/CH VIH Logic high input voltage, TX_SYNC pin Support 1.8-V and 3.3-V CMOS logic 1.3 3.3 VIL Logic low input voltage, TX_SYNC pin Support 1.8-V and 3.3-V CMOS logic 0 0.3 IIH Logic high input current, TX_SYNC pin VHIGH = 1.8 V IIL Logic low input current, TX_SYNC pin VLOW = 0 V 12 Submit Documentation Feedback V V 11 µA < 0.1 µA Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 DIGITAL CHARACTERISTICS Typical values are at +25°C, AVDD = 3.3 V, AVDD_5 = 5 V and AVDD_ADC = 1.8 V, DVDD = 1.8 V unless otherwise noted. Minimum and maximum values are across the full temperature range: TMIN = 0°C to TMAX = +85°C. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT (1) DIGITAL INPUTS/OUTPUTS VIH Logic high input voltage 2 3.3 VIL Logic low input voltage 0 0.3 V V Logic high input current 200 µA Logic low input current 200 µA 5 pF VOH Input capacitance Logic high output voltage SDOUT pin DVDD V VOL Logic low output voltage SDOUT pin 0 V 400 mV LVDS OUTPUTS Output differential voltage With 100-Ω external differential termination Output offset voltage Common-mode voltage FCLKP and FCLKM 1X clock rate 10 65 MHz DCLKP and DCLKM 7X clock rate 70 455 MHz 6X clock rate 60 390 MHz 1100 (2) tsu Data setup time th Data hold time (2) mV 350 ps 350 ps ADC INPUT CLOCK CLOCK frequency 10 Clock duty cycle 45% Sine-wave, AC-coupled Clock input amplitude, differential(VCLKP_ADC – VCLKM_ADC) Common-mode voltage (2) MSPS 55% 0.5 Vpp LVPECL, AC-coupled 1.6 Vpp LVDS, AC-coupled 0.7 Vpp 1 V 1.8 Vpp Biased internally Clock input amplitude VCLKP_ADC (singleCMOS CLOCK ended) (1) 65 50% The DC specifications refer to the condition where the LVDS outputs are not switching, but are permanently at a valid logic level 0 or 1 with 100-Ω external termination. Setup and hold time specifications take into account the effect of jitter on the output data and clock. These specifications also assume that the data and clock paths are perfectly matched within the receiver. Any mismatch in these paths within the receiver would appear as reduced timing margins Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 13 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com TYPICAL CHARACTERISTICS AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, AC-coupled with 0.1-µF caps at INP and 15-nF caps at INM, No active termination, VCNTL = 0 V, FIN = 5 MHz, LNA = 18 dB, PGA = 24 dB, 14 Bit, sample rate = 65 MSPS, LPF Filter = 15 MHz, low noise mode, Single-ended VCNTL mode, VCNTLM = GND, ADC is configured in internal reference mode, VOUT = –1 dBFS, 500-Ω CW feedback resistor, CMOS 16X clock, digital demodulator is disabled, at ambient temperature TA = +25°C, unless otherwise noted. 45 45 Low noise Medium power Low power 40 35 35 30 Gain (dB) 25 20 25 20 15 15 10 10 5 5 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 Vcntl (V) 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) Figure 3. Gain Variation vs Temperature, LNA = 18 dB and PGA = 24 dB 9000 8000 8000 7000 7000 3000 Gain (dB) 0.6 0.5 G005 Figure 4. Gain Matching Histogram, VCNTL = 0.3 V (34951 Channels) Figure 5. Gain Matching Histogram, VCNTL = 0.6 V (34951 Channels) Number of Occurrences 7000 Number of Occurrences 0.4 Gain (dB) G004 8000 6000 5000 4000 3000 2000 1000 120 110 100 90 80 70 60 50 40 30 20 10 0 −72 −68 −64 −60 −56 −52 −48 −44 −40 −36 −32 −28 −24 −20 −16 −12 −8 −4 0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 68 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 −0.1 −0.2 −0.3 −0.4 −0.5 −0.6 −0.7 0 Gain (dB) ADC Output G005 Figure 6. Gain Matching Histogram, VCNTL = 0.9 V (34951 Channels) 14 0.3 −0.7 0.5 0.4 0.3 0.2 0 0.1 −0.1 −0.2 −0.3 −0.4 −0.5 −0.6 −0.7 0 −0.8 1000 0 −0.9 1000 0.2 2000 0 2000 4000 0.1 3000 5000 −0.1 4000 −0.2 5000 6000 −0.3 6000 −0.4 Number of Occurrences 9000 −0.5 Figure 2. Gain vs VCNTL, LNA = 18 dB and PGA = 24 dB −0.6 Gain (dB) 30 Number of Occurrences −40 deg C 25 deg C 85 deg C 40 G058 Figure 7. Output Offset Histogram, VCNTL = 0 V (1247 Channels) Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 TYPICAL CHARACTERISTICS (continued) Impedance Magnitude Response Impedance Phase Response 10 Open 12000 −10 Phase (Degrees) 10000 Impedance (Ohms) Open 0 8000 6000 4000 −20 −30 −40 −50 −60 −70 2000 −80 500k 4.5M 8.5M 12.5M 16.5M −90 500k 20.5M 4.5M 8.5M Frequency (Hz) 20.5M Figure 9. Input Impedance Without Active Termination (Phase) Impedance Magnitude Response Impedance Phase Response 500 10 50 Ohms 100 Ohms 200 Ohms 400 Ohms 450 400 350 0 −10 Phase (Degrees) Impedance (Ohms) 16.5M Frequency (Hz) Figure 8. Input Impedance Without Active Termination (Magnitude) 300 250 200 150 −20 −30 −40 −50 −60 100 −70 50 −80 0 500k 4.5M 8.5M 12.5M 16.5M 50 Ohms 100 Ohms 200 Ohms 400 Ohms −90 500k 20.5M Frequency (Hz) 4.5M 8.5M 12.5M 16.5M 20.5M Frequency (Hz) Figure 10. Input Impedance With Active Termination (Magnitude) Figure 11. Input Impedance With Active Termination (Phase) LNA INPUT HPF CHARECTERISTICS 5 10MHz 15MHz 20MHz 30MHz 0 −5 3 0 −3 −6 Amplitude (dB) Amplitude (dB) 12.5M −10 −15 −20 −9 −12 −15 −18 −21 −25 −30 01 00 11 10 −24 −27 0 10 20 30 40 50 Frequency (MHz) 60 −30 10 100 500 Frequency (KHz) Figure 12. Low-Pass Filter Response Figure 13. LNA High-Pass Filter Response vs Reg59[3:2] Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 15 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com TYPICAL CHARACTERISTICS (continued) HPF CHARECTERISTICS (LNA+VCA+PGA+ADC) −146 −148 −5 −150 Phase Noise (dBc/Hz) 0 −10 Amplitude (dB) Single Channel CW PN −144 5 −15 −20 −25 −30 16X Clock Mode 8X Clock Mode 4X Clock Mode −152 −154 −156 −158 −160 −162 −164 −166 −35 −40 −168 10 100 −170 100 500 1000 Frequency (KHz) Figure 15. CW Phase Noise, FIN = 2 MHz Phase Noise −146 PN 1 Ch PN 8 Ch −148 16X Clock Mode 8X Clock Mode 4X Clock Mode −148 −150 Phase Noise (dBc/Hz) −150 Phase Noise (dBc/Hz) Eight Channel CW PN −144 −146 −152 −154 −156 −158 −160 −162 −164 −152 −154 −156 −158 −160 −162 −164 −166 −166 −168 −168 −170 100 1000 10000 50000 −170 100 1000 Frequency Offset (Hz) Hz) Input reffered noise (nV Hz) Input reffered noise (nV 3.5 LNA 12 dB LNA 18 dB LNA 24 dB 30 20 10 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) Figure 18. IRN, PGA = 24 dB and Low Noise Mode 16 50000 Figure 17. CW Phase Noise vs Clock Modes, FIN= 2 MHz 60 40 10000 Offset frequency (Hz) Figure 16. CW Phase Noise, FIN = 2 MHz, 1 Channel vs 8 Channel 50 50000 Offset frequency (Hz) Figure 14. Full Channel High-Pass Filter Response at Default Register Setting −144 10000 3.0 LNA 12 dB LNA 18 dB LNA 24 dB 2.5 2.0 1.5 1.0 0.5 0.0 0.0 0.1 0.2 Vcntl (V) 0.3 0.4 Figure 19. IRN, PGA = 24 dB and Low Noise Mode Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 TYPICAL CHARACTERISTICS (continued) Hz) 60 4.0 LNA 12 dB LNA 18 dB LNA 24 dB 50 Input reffered noise (nV Input reffered noise (nV Hz) 70 40 30 20 10 2.0 1.5 1.0 0.1 0.2 Vcntl (V) 0.3 0.4 Figure 21. IRN, PGA = 24 dB and Medium Power Mode 70 4.0 Hz) 60 LNA 12 dB LNA 18 dB LNA 24 dB 50 40 30 20 10 190 LNA 12 dB LNA 18 dB LNA 24 dB Output reffered noise (nV 170 150 130 110 90 70 50 30 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) Figure 24. ORN, PGA = 24 dB and Low Noise Mode LNA 12 dB LNA 18 dB LNA 24 dB 3.0 2.5 2.0 1.5 1.0 0.1 0.2 Vcntl (V) 0.3 0.4 Figure 23. IRN, PGA = 24 dB and Low Power Mode Hz) 220 210 3.5 0.5 0.0 Figure 22. IRN, PGA = 24 dB and Low Power Mode Hz) 2.5 Figure 20. IRN, PGA = 24 dB and Medium Power Mode 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) Output reffered noise (nV LNA 12 dB LNA 18 dB LNA 24 dB 3.0 0.5 0.0 Input reffered noise (nV Input reffered noise (nV Hz) 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) 3.5 300 280 260 240 220 200 180 160 140 120 100 80 60 40 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Vcntl (V) LNA 12 dB LNA 18 dB LNA 24 dB 1.0 1.1 1.2 Figure 25. ORN, PGA = 24 dB and Medium Power Mode Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 17 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Output reffered noise (nV Hz) TYPICAL CHARACTERISTICS (continued) 340 320 300 280 260 240 220 200 180 160 140 120 100 80 60 40 LNA 12 dB LNA 18 dB LNA 24 dB 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Vcntl (V) 1 1.1 1.2 Figure 26. ORN, PGA = 24 dB and Low Power Mode Figure 27. IRN, PGA = 24 dB and Low Noise Mode 75 180.0 120.0 70 SNR (dBFS) Hz) 140.0 Amplitude (nV 160.0 100.0 80.0 65 60 60.0 40.0 1.0 24 dB PGA gain 30 dB PGA gain 3.0 5.0 7.0 Frequency (MHz) 9.0 55 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) 11.0 12.0 Figure 28. ORN, PGA = 24 dB and Low Noise Mode Figure 29. SNR, LNA = 18 dB and Low Noise Mode 75 73 Low noise Low power 71 69 SNR (dBFS) SNR (dBFS) 70 65 60 67 65 63 61 24 dB PGA gain 30 dB PGA gain 55 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 Vcntl (V) 59 57 0 Figure 30. SNR, LNA = 18 dB and Low Power Mode 18 Submit Documentation Feedback 3 6 9 12 15 18 21 24 27 30 33 36 39 42 Gain (dB) Figure 31. SNR vs Different Power Modes Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 TYPICAL CHARACTERISTICS (continued) 9 10 100 ohm act term 200 ohm act term 400 ohm act term Without Termination 8 8 Noise Figure (dB) Noise Figure (dB) 7 6 5 4 3 7 6 5 4 3 2 2 1 1 0 50 100 150 200 50 ohm act term 100 ohm act term 200 ohm act term 400 ohm act term Without Termination 9 250 300 350 0 400 50 100 150 Source Impedence (Ω) 200 250 300 350 400 Source Impedence (Ω) Figure 32. Noise Figure, LNA = 12 dB and Low Noise Mode Figure 33. Noise Figure, LNA = 18 dB and Low Noise Mode 8 50 ohm act term 100 ohm act term 200 ohm act term 400 ohm act term No Termination 7 Noise Figure (dB) 6 5 4 3 2 1 0 50 100 150 200 250 300 350 400 Source Impedence (Ω) Figure 34. Noise Figure, LNA = 24 dB and Low Noise Mode Figure 35. Noise Figure vs Power Modes With 400-Ω Termination −50.0 Low noise Low power Medium power −55.0 HD2 (dB) −60.0 −65.0 −70.0 −75.0 −80.0 Figure 36. Noise Figure vs Power Modes Without Termination 1 2 3 4 5 6 7 Frequency (MHz) 8 9 10 Figure 37. HD2 vs Frequency, VIN = 500 mVpp and VOUT = –1 dBFS Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 19 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com TYPICAL CHARACTERISTICS (continued) −45 −40 Low noise Low power Medium power −50 −50 −55 HD2 (dBc) −55 HD3 (dBc) Low noise Low power Medium power −45 −60 −65 −60 −65 −70 −75 −80 −70 −85 −75 1 2 3 4 5 6 7 Frequency (MHz) 8 9 −90 10 18 24 30 36 Figure 39. HD2 vs Gain, LNA = 12 dB and PGA = 24 dB and VOUT = –1 dBFS −40 −40 Low noise Low power Medium power −60 −70 Low noise Low power Medium power −50 HD2 (dBc) −50 HD3 (dBc) 12 Gain (dB) Figure 38. HD3 vs Frequency, VIN = 500 mVpp and VOUT = –1 dBFS −80 −90 6 −60 −70 −80 6 12 18 24 30 −90 36 12 18 24 Gain (dB) 30 36 42 Gain (dB) Figure 40. HD3 vs Gain, LNA = 12 dB and PGA = 24 dB and VOUT = –1 dBFS Figure 41. HD2 vs Gain, LNA = 18 dB and PGA = 24 dB and VOUT = –1 dBFS −40 −40 Low noise Low power Medium power −50 Low noise Low power Medium power −45 −50 HD2 (dBc) HD3 (dBc) −55 −60 −70 −60 −65 −70 −75 −80 −80 −85 −90 12 18 24 30 36 42 −90 18 Gain (dB) 30 36 42 48 Gain (dB) Figure 42. HD3 vs Gain, LNA = 18 dB and PGA = 24 dB and VOUT = –1 dBFS 20 24 Figure 43. HD2 vs Gain, LNA = 24 dB and PGA = 24 dB and VOUT = –1 dBFS Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 TYPICAL CHARACTERISTICS (continued) −50 −40 Fin1=2MHz, Fin2=2.01MHz Fin1=5MHz, Fin2=5.01MHz Low noise Low power Medium power −54 IMD3 (dBFS) −50 HD3 (dB) −60 −70 −58 −62 −66 −80 −70 −90 18 21 24 27 30 33 36 Gain (dB) 39 42 45 14 18 22 48 Figure 44. HD3 vs Gain, LNA = 24 dB and PGA = 24 dB and VOUT = –1 dBFS 26 30 Gain (dB) 42 G001 PSMR vs SUPPLY FREQUENCY Fin1=2MHz, Fin2=2.01MHz Fin1=5MHz, Fin2=5.01MHz −60 Vcntl = 0 Vcntl = 0.3 Vcntl = 0.6 Vcntl = 0.9 −54 −58 PSMR (dBc) IMD3 (dBFS) 38 Figure 45. IMD3, Fout1 = –7 dBFS and Fout2 = –21 dBFS −50 −62 −66 −70 34 −65 −70 14 18 22 26 30 Gain (dB) 34 38 42 −75 G001 5 10 100 1000 2000 Supply frequency (kHz) Figure 46. IMD3, Fout1 = –7 dBFS and Fout2 = –7 dBFS Figure 47. AVDD Power Supply Modulation Ratio, 100 mVpp Supply Noise with Different Frequencies PSMR vs SUPPLY FREQUENCY 3V PSRR vs SUPPLY FREQUENCY −20 −55 PSMR (dBc) −60 −65 −70 −75 Vcntl = 0 Vcntl = 0.3 Vcntl = 0.6 Vcntl = 0.9 −30 PSRR wrt supply tone (dB) Vcntl = 0 Vcntl = 0.3 Vcntl = 0.6 Vcntl = 0.9 −40 −50 −60 −70 −80 −80 5 10 100 1000 2000 −90 5 Supply frequency (kHz) 10 100 1000 2000 Supply frequency (kHz) Figure 48. AVDD_5V Power Supply Modulation Ratio, 100 mVpp Supply Noise With Different Frequencies Figure 49. AVDD Power Supply Rejection Ratio, 100 mVpp Supply Noise With Different Frequencies Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 21 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com 20000.0 −20 Vcntl = 0 Vcntl = 0.3 Vcntl = 0.6 Vcntl = 0.9 −40 16000.0 14000.0 Output Code PSRR wrt supply tone (dB) −30 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 −0.1 3.0 Output Code Vcntl 18000.0 −50 −60 12000.0 10000.0 8000.0 6000.0 4000.0 −70 2000.0 −80 −90 0.0 0.0 5 10 100 0.5 1.0 1.5 Time (µs) 2.0 2.5 Vcntl (V) TYPICAL CHARACTERISTICS (continued) 5V PSRR vs SUPPLY FREQUENCY 1000 2000 Supply frequency (kHz) Figure 50. AVDD_5V Power Supply Rejection Ratio, 100 mVpp Supply Noise With Different Frequencies Output Code Vcntl 16000.0 Output Code 14000.0 12000.0 10000.0 8000.0 6000.0 4000.0 2000.0 0.0 0.0 0.2 0.5 0.8 1.0 1.2 1.5 Time (µs) 1.8 2.0 2.2 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 −0.1 2.5 1.2 1.0 0.8 0.6 0.4 Input (V) 18000.0 Vcntl (V) 20000.0 Figure 51. VCNTL Response Time, LNA = 18 dB and PGA = 24 dB 0.2 0.0 −0.2 −0.4 −0.6 −0.8 −1.0 −1.2 0.0 Figure 52. VCNTL Response Time, LNA = 18 dB and PGA = 24 dB 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 Time (µs) Figure 53. Pulse Inversion Asymmetrical Positive Input 1.2 10000.0 1.0 8000.0 0.8 Positive overload Negative overload Average 6000.0 0.6 4000.0 Output Code Input (V) 0.4 0.2 0.0 −0.2 −0.4 2000.0 0.0 −2000.0 −4000.0 −0.6 −6000.0 −0.8 −8000.0 −1.0 −1.2 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 Time (µs) Figure 54. Pulse Inversion Asymmetrical Negative Input 22 −10000.0 0.0 1.0 2.0 3.0 Time (µs) 4.0 5.0 6.0 Figure 55. Pulse Inversion, VIN = 2 Vpp, PRF = 1 kHz, Gain = 21 dB Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 TYPICAL CHARACTERISTICS (continued) 10000 2000 47nF 15nF 6000 1200 4000 800 2000 0 −2000 400 0 −400 −4000 −800 −6000 −1200 −8000 −1600 −10000 0 0.5 1 1.5 2 2.5 3 Time (µs) 3.5 4 4.5 47nF 15nF 1600 Output Code Output Code 8000 5 Figure 56. Overload Recovery Response vs INM Capacitor, VIN = 50 mVpp/100 µVpp, Max Gain −2000 1 1.5 2 2.5 3 3.5 Time (µs) 4 4.5 5 Figure 57. Overload Recovery Response vs INM Capacitor (Zoomed), VIN = 50 mVpp/100 µVpp, Max Gain 10 5 0 Gain (dB) −5 k=2 k=3 k=4 k=5 k=6 k=7 k=8 k=9 k=10 −10 −15 −20 −25 −30 −35 −40 0 0.2 0.4 0.6 0.8 1 1.2 1.4 Frequency (MHz) 1.6 1.8 2 G000 Figure 58. Digital High-Pass Filter Response Figure 59. Signal Chain Low Frequency Response With INM Capacitor = 1 µF Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 23 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com TIMING CHARACTERISTICS (1) Typical values are at 25°C, AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V, Differential clock, CLOAD = 5 pF, RLOAD = 100 Ω, 14 Bit, sample rate = 65 MSPS, digital demodulator is disabled, unless otherwise noted. Minimum and maximum values are across the full temperature range TMIN = 0°C to TMAX = 85°C with AVDD_5 V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V PARAMETER ta tj TEST CONDITIONS MIN Aperture delay The delay in time between the rising edge of the input sampling clock and the actual time at which the sampling occurs Aperture delay matching Across channels within the same device 0.7 Aperture jitter TYP MAX 3 ns ±150 ps 450 Fs rms 11/8 Input clock cycles ADC latency Default, after reset, or / 0 x 2 [12] = 1, LOW_LATENCY = 1 tdelay Data and frame clock delay Input clock rising edge (zero cross) to frame clock rising edge (zero cross) minus 3/7 of the input clock period (T). Δtdelay Delay variation At fixed supply and 20°C T difference. Device to device tRISE Data rise time 0.14 tFALL Data fall time Rise time measured from –100 to 100 mV Fall time measured from 100 to –100 mV 10 MHz < fCLKIN < 65 MHz tFCLKRISE Frame clock rise time 0.14 tFCLKFALL Frame clock fall time Rise time measured from –100 to 100 mV Fall time measured from 100 to –100 mV 10 MHz < fCLKIN < 65 MHz Frame clock duty cycle Zero crossing of the rising edge to zero crossing of the falling edge tDCLKRISE tDCLKFALL (1) 3 5.4 –1 Bit clock rise time Bit clock fall time Rise time measured from –100 to 100 mV Fall time measured from 100 to –100 mV 10 MHz < fCLKIN < 65 MHz Bit clock duty cycle Zero crossing of the rising edge to zero crossing of the falling edge 10 MHz < fCLKIN < 65 MHz UNIT 7 ns 1 ns ns 0.15 ns 0.15 48% 50% 52% 0.13 ns 0.12 46% 54% Timing parameters are ensured by design and characterization; not production tested. OUTPUT INTERFACE TIMING (14-bit) (1) (2) (3) fCLKIN, Input Clock Frequency (1) (2) (3) Setup Time (tsu), ns (for output data and frame clock) Hold Time (th), ns (for output data and frame clock) tPROG = (3/7)x T + tdelay, ns Data Valid to Bit Clock ZeroCrossing Bit Clock Zero-Crossing to Data Invalid Input Clock Zero-Cross (rising edge) to Frame Clock Zero-Cross (rising edge) MHz MIN TYP MIN TYP MIN TYP MAX 65 0.24 0.37 MAX 0.24 0.38 MAX 11 12 12.5 50 0.41 0.54 0.46 0.57 13 13.9 14.4 40 0.55 0.70 0.61 0.73 15 16 16.7 30 0.87 1.10 0.94 1.1 18.5 19.5 20.1 20 1.30 1.56 1.46 1.6 25.7 26.7 27.3 FCLK timing is the same as for the output data lines. It has the same relation to DCLK as the data pins. Setup and hold are the same for the data and the frame clock. Data valid is logic HIGH = +100 mV and logic LOW = –100 mV Timing parameters are ensured by design and characterization; not production tested. SPACER NOTE The above timing data can be applied to 12-bit or 16-bit LVDS rates as well. For example, the maximum LVDS output rate at 65 MHz and 14-bit is equal to 910 MSPS, which is approximately equivalent to the rate at 56 MHz and 16-bit. 24 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 12-Bit 6x serialization mode Output Data CHnOUT Data rate = 14 x fCLKIN Bit Clock DCLK Freq = 7 x fCLKIN Frame Clock FCLK Freq = fCLKIN Input Clock CLKIN Freq = fCLKIN Input Signal D0 D13 D12 D1 (D12) (D13) (D0) (D1) D11 (D2) Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 D6 D5 (D7) (D8) Output Data Pair Data bit in LSB First mode Bit Clock DCLKP D13 D12 (D0) (D1) CHi out tsu DCLKM D4 D3 D2 D1 D0 (D9) (D10) (D11) (D12) (D13) Data bit in MSB First mode SAMPLE N-Cd D8 D7 (D5) (D6) Cd clock cycles latency th D11 D10 (D2) (D3) Dn D7 D6 (D6) (D7) SAMPLE N-1 D9 D8 (D4) (D5) Sample N+Cd ta Dn + 1 tsu th D5 D4 D3 D2 D1 D0 D13 D12 (D8) (D9) (D10) (D11) (D12) (D13) (D0) (D1) tPROG D11 D10 (D2) (D3) T D7 D6 (D6) (D7) SAMPLE N D9 D8 (D4) (D5) Sample N+Cd+1 D10 (D1) T0434-01 D1 D0 D11 D5 D4 D3 D2 (D8) (D9) (D10) (D11) (D12) (D13) (D0) www.ti.com D13 (D0) D10 D9 (D3) (D4) ta Sample N tPROG AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 LVDS Setup and Hold Timing 14-Bit 7x serialization mode Figure 60. LVDS Timing Diagrams Submit Documentation Feedback 25 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com LVDS Output Interface Description AFE5809 has LVDS output interface which supports multiple output formats. The ADC resolutions can be configured as 12 bit or 14 bit as shown in the LVDS timing diagrams Figure 60. The ADCs in the AFE5809 are running at 14 bit; 2 LSBs are removed when 12-bit output is selected; and two 0s are added at LSBs when 16-bit output is selected. Appropriate ADC resolutions can be selected for optimizing system performance-cost effectiveness. When the devices run at 16bit mode, higher end FPGAs are required to process higher rate of LVDS data. Corresponding register settings are listed in Table 4. Table 4. Corresponding Register Settings LVDS Rate 26 12 bit (6X DCLK) 14 bit (7X DCLK) 16 bit (8X DCLK) Reg 3 [14:13] 11 00 01 Reg 4 [2:0] 010 000 000 Description 2 LSBs removed N/A 2 0s added at LSBs Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Serial Peripheral Interface (SPI) Operation Serial Register Write Description Programming of different modes can be done through the serial interface formed by pins SEN (serial interface enable), SCLK (serial interface clock), SDATA (serial interface data) and RESET. All these pins have a pull-down resistor to GND of 20 kΩ . Serial shift of bits into the device is enabled when SEN is low. Serial data SDATA is latched at every rising edge of SCLK when SEN is active (low). The serial data is loaded into the register at every 24th SCLK rising edge when SEN is low. If the word length exceeds a multiple of 24 bits, the excess bits are ignored. Data can be loaded in multiple of 24-bit words within a single active SEN pulse (there is an internal counter that counts groups of 24 clocks after the falling edge of SEN). The interface can work with the SCLK frequency from 20 MHz down to low speeds (few Hertz) and even with non-50% duty cycle SCLK. The data is divided into two main portions: a register address (8 bits) and the data itself (16 bits), to load on the addressed register. When writing to a register with unused bits, these should be set to 0. Figure 61 shows this process. Start Sequence End Sequence SEN t6 t7 t1 t2 Data Latched On Rising Edge of SCLK SCLK t3 SDATA A7 A5 A6 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 t4 t5 Start Sequence End Sequence RESET T0384-01 Figure 61. SPI Timing Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 27 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com SPI Timing Characteristics Minimum values across full temperature range TMIN = 0°C to TMAX = 85°C, AVDD_5V = 5 V, AVDD = 3.3 V, AVDD_ADC = 1.8 V, DVDD = 1.8 V PARAMETER DESCRIPTION MIN TYP MAX UNIT t1 SCLK period 50 ns t2 SCLK high time 20 ns t3 SCLK low time 20 ns t4 Data setup time 5 ns t5 Data hold time 5 ns t6 SEN fall to SCLK rise 8 ns t7 Time between last SCLK rising edge to SEN rising edge t8 SDOUT delay 8 ns 12 20 28 ns Serial Register Readout The device includes an option where the contents of the internal registers can be read back. This may be useful as a diagnostic test to verify the serial interface communication between the external controller and the AFE. First, the <REGISTER READOUT ENABLE> bit (Reg0[1]) needs to be set to '1'. Then user should initiate a serial interface cycle specifying the address of the register (A7-A0) whose content has to be read. The data bits are "don’t care". The device will output the contents (D15-D0) of the selected register on the SDOUT pin. SDOUT has a typical delay, t8, of 20 ns from the falling edge of the SCLK. For lower speed SCLK, SDOUT can be latched on the rising edge of SCLK. For higher speed SCLK, for example, the SCLK period lesser than 60 ns, it is better to latch the SDOUT at the next falling edge of SCLK. The following timing diagram shows this operation (the time specifications follow the same information provided. In the readout mode, users still can access the <REGISTER READOUT ENABLE> through SDATA/SCLK/SEN. To enable serial register writes, set the <REGISTER READOUT ENABLE> bit back to '0'. Start Sequence End Sequence SEN t6 t7 t1 t2 SCLK t3 A7 SDATA A6 A5 A4 A3 t4 A2 A1 A0 x x x x x x x x x x x x x x x x D6 D5 D4 D3 D2 D1 D0 t8 t5 D15 D14 D13 D12 D11 D10 D9 SDOUT D8 D7 Figure 62. Serial Interface Register Read The AFE5809 SDOUT buffer is tri-stated and will get enabled only when 0[1] (REGISTER READOUT ENABLE) is enabled. SDOUT pins from multiple AFE5809s can be tied together without any pull-up resistors. Level shifter SN74AUP1T04 can be used to convert 1.8-V logic to 2.5-V/3.3-V logics if needed. 28 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 t1 AVDD AVDD_5V AVDD_ADC t2 DVDD t3 t4 t7 t5 RESET t6 Device Ready for Serial Register Write SEN Start of Clock Device Ready for Data Conversion CLKP_ADC t8 10 μs < t1 < 50 ms, 10 μs < t2 < 50 ms, –10 ms < t3 < 10 ms, t4 > 10 ms, t5 > 100 ns, t6 > 100 ns, t7 > 10 ms, and t8 > 100 μs. The AVDDx and DVDD power-on sequence does not matter as long as –10 ms < t3 < 10 ms. Similar considerations apply while shutting down the device. Figure 63. Recommended Power-up Sequencing and Reset Timing Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 29 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com ADC and VCA Register Description A reset process is required at the AFE5809 initialization stage. Initialization can be done in one of two ways: 1. Through a hardware reset, by applying a positive pulse in the RESET pin 2. Through a software reset, using the serial interface, by setting the SOFTWARE RESET bit to high. Setting this bit initializes the internal registers to the respective default values (all zeros) and then self-resets the SOFTWARE RESET bit to low. In this case, the RESET pin can stay low (inactive). After reset, all ADC and VCA registers are set to '0', that is default setting. During register programming, all unlisted register bits need to be set as '0'. Note some demodulator registers are set as '1' after reset. During register programming, all unlisted register bits need to be set as '0'. In addition, the demodulator registers can be reset when 0x16[0] is set as '0'. Thus it is required to reconfigure the demodulator registers after toggling the 0x16[0] from '1' to '0'. ADC Register Map Table 5. ADC Register Map ADDRESS (DEC) ADDRESS (HEX) DEFAULT VALUE 0[0] 0x0[0] 0 SOFTWARE_RESET 0: Normal operation; 1: Resets the device and self-clears the bit to '0' 0[1] 0x0[1] 0 REGISTER_READOUT_ENABLE 0:Disables readout; 1: enables readout of register at SDOUT Pin 1[0] 0x1[0] 0 ADC_COMPLETE_PDN 0: Normal 1: Complete Power down 1[1] 0x1[1] 0 LVDS_OUTPUT_DISABLE 0: Output Enabled; 1: Output disabled 1[9:2] 0x1[9:2] 0 ADC_PDN_CH<7:0> 0: Normal operation; 1: Power down. Power down Individual ADC channels. 1[9]→CH8…1[2]→CH1 1[10] 0x1[10] 0 PARTIAL_PDN 0: Normal Operation; 1: Partial Power Down ADC 1[11] 0x1[11] 0 LOW_FREQUENCY_ NOISE_SUPPRESSION 0: No suppression; 1: Suppression Enabled 1[13] 0x1[13] 0 EXT_REF 0: Internal Reference; 1: External Reference. VREF_IN is used. Both 3[15] and 1[13] should be set as 1 in the external reference mode 1[14] 0x1[14] 0 LVDS_OUTPUT_RATE_2X 0: 1x rate; 1: 2x rate. Combines data from 2 channels on 1 LVDS pair. When ADC clock rate is low, this feature can be used 1[15] 0x1[15] 0 SINGLE-ENDED_CLK_MODE 0: Differential clock input; 1: Single-ended clock input 2[2:0] 0x2[2:0] 0 RESERVED Set to 0 2[10:3] 0x2[10:3] 0 POWER-DOWN_LVDS 0: Normal operation; 1: PDN Individual LVDS outputs. 2[10]→CH8…2[3]→CH1 2[11] 0x2[11] 0 AVERAGING_ENABLE 0: No averaging; 1: Average 2 channels to increase SNR 2[12] 0x2[12] 0 LOW_LATENCY 0: Default Latency with digital features supported 1: Low Latency with digital features bypassed. 2[15:13] 0x2[15:13] 0 TEST_PATTERN_MODES 000: Normal operation; 001: Sync; 010: De-skew; 011: Custom; 100:All 1's; 101: Toggle; 110: All 0's; 111: Ramp. 3[7:0] 0x3[7:0] 0 INVERT_CHANNELS 0: No inverting; 1:Invert channel digital output. 3[7]→CH8;3[0]→CH1 3[8] 0x3[8] 0 CHANNEL_OFFSET_ SUBSTRACTION_ENABLE 0: No offset subtraction; 1: Offset value Subtract Enabled 30 FUNCTION DESCRIPTION Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Table 5. ADC Register Map (continued) ADDRESS (DEC) ADDRESS (HEX) DEFAULT VALUE 3[9:11] 0x3[9:11] 0 RESERVED Set to 0 3[12] 0x3[12] 0 DIGITAL_GAIN_ENABLE 0: No digital gain; 1: Digital gain Enabled 3[14:13] 0x3[14:13] 0 SERIALIZED_DATA_RATE Serialization factor 00: 14x 01: 16x 10: reserved 11: 12x when 4[1] = 1. In the 16x serialization rate, two 0s are filled at two LSBs (see Table 4). Note: Make sure the settings aligning with the demod register 0x3[14:13]. Please also aware that the same setting , for example "00", in these two registers can represent different LVDS data rates respectively. 3[15] 0x3[15] 0 ENABLE_EXTERNAL_ REFERENCE_MODE 0: Internal reference mode; 1: Set to external reference mode Note: Both 3[15] and 1[13] should be set as 1 when configuring the device in the external reference mode 4[1] 0x4[1] 0 ADC_RESOLUTION_SELECT 0: 14 bit; 1: 12 bit 4[3] 0x4[3] 0 ADC_OUTPUT_FORMAT 0: 2's complement; 1: Offset binary Note: When the demodulation feature is enabled, only 2's complement format can be selected. 4[4] 0x4[4] 0 LSB_MSB_FIRST 0: LSB first; 1: MSB first 5[13:0] 0x5[13:0] 0 CUSTOM_PATTERN Custom pattern data for LVDS output (2[15:13] = 011) 10[8] 0xA[8] 0 SYNC_PATTERN 0: Test pattern outputs of 8 channels are NOT synchronized. 1: Test pattern outputs of 8 channels are synchronized. 13[9:0] 0xD[9:0] 0 OFFSET_CH1 Value to be subtracted from channel 1 code 13[15:11] 0xD[15:11] 0 DIGITAL_GAIN_CH1 0 to 6 dB in 0.2-dB steps 15[9:0] 0xF[9:0] 0 OFFSET_CH2 value to be subtracted from channel 2 code 15[15:11] 0xF[15:11] 0 DIGITAL_GAIN_CH2 0 to 6 dB in 0.2-dB steps 17[9:0] 0x11[9:0] 0 OFFSET_CH3 value to be subtracted from channel 3 code 17[15:11] 0x11[15:11] 0 DIGITAL_GAIN_CH3 0 to 6 dB in 0.2-dB steps 19[9:0] 0x13[9:0] 0 OFFSET_CH4 value to be subtracted from channel 4 code 19[15:11] 0x13[15:11] 0 DIGITAL_GAIN_CH4 0 to 6 dB in 0.2-dB steps 21[0] 0x15[0] 0 DIGITAL_HPF_FILTER_ENABLE _ CH1-4 0: Disable the digital HPF filter; 1: Enable for 1-4 channels Note: This HPF feature is only available when the demodulation block is disabled. 21[4:1] 0x15[4:1] 0 DIGITAL_HPF_FILTER_K_CH1-4 Set K for the high-pass filter (k from 2 to 10, that is 0010B to 1010B). This group of four registers controls the characteristics of a digital high-pass transfer function applied to the output data, following the formula: y(n) = 2k/(2k + 1) [x(n) – x(n – 1) + y(n – 1)] (please see Table 6) 22[0] 0x16[0] 0 EN_DEMOD 0: Digital demodulator is enabled 1: Digital demodulator is disabled Note: The demodulator registers can be reset when 0x16[0] is set as '0'. Thus it is required to reconfigure the demodulator registers after toggling the 0x16[0]. 25[9:0] 0x19[9:0] 0 OFFSET_CH8 value to be subtracted from channel 8 code 25[15:11] 0x19[15:11] 0 DIGITAL_GAIN_CH8 0 to 6-dB in 0.2-dB steps 27[9:0] 0x1B[9:0] 0 OFFSET_CH7 value to be subtracted from channel 7 code 27[15:11] 0x1B[15:11] 0 DIGITAL_GAIN_CH7 0 to 6-dB in 0.2-dB steps 29[9:0] 0x1D[9:0] 0 OFFSET_CH6 value to be subtracted from channel 6 code 29[15:11] 0x1D[15:11] 0 DIGITAL_GAIN_CH6 0 to 6-dB in 0.2-dB steps 31[9:0] 0x1F[9:0] 0 OFFSET_CH5 value to be subtracted from channel 5 code 31[15:11] 0x1F[15:11] 0 DIGITAL_GAIN_CH5 0 to 6-dB in 0.2-dB steps FUNCTION DESCRIPTION Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 31 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Table 5. ADC Register Map (continued) ADDRESS (DEC) ADDRESS (HEX) DEFAULT VALUE 33[0] 0x21[0] 0 DIGITAL_HPF_FILTER_ENABLE _ CH5-8 0: Disable the digital HPF filter; 1: Enable for 5-8 channels Note: This HPF feature is only available when the demodulation block is disabled. 33[4:1] 0x21[4:1] 0 DIGITAL_HPF_FILTER_K_CH5-8 Set K for the high-pass filter (k from 2 to 10, 0010B to 1010B) This group of four registers controls the characteristics of a digital high-pass transfer function applied to the output data, following the formula: y(n) = 2k / (2k + 1) [x(n) – x(n – 1) + y(n – 1)] (please see Table 6) 32 FUNCTION DESCRIPTION Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 AFE5809 ADC Register/Digital Processing Description The ADC in the AFE5809 has extensive digital processing functionalities which can be used to enhance ultrasound system performance. The digital processing blocks are arranged as in Figure 64. ADC Output 12/14b Channel Average Default=No Digital Gain Default=0 Digital HPF Default = No 12/14b Final Digital Output Digital Offset Default=No Figure 64. ADC Digital Block Diagram NOTE These digital processing features are only avaiable when the demodulation block is disabled. ADC output data directly enter the digital demodulator when the demod is enabled. AVERAGING_ENABLE: Address: 2[11] When set to 1, two samples, corresponding to two consecutive channels, are averaged (channel 1 with 2, 3 with 4, 5 with 6, and 7 with 8). If both channels receive the same input, the net effect is an improvement in SNR. The averaging is performed as: • Channel 1 + channel 2 comes out on channel 3 • Channel 3 + channel 4 comes out on channel 4 • Channel 5 + channel 6 comes out on channel 5 • Channel 7 + channel 8 comes out on channel 6 ADC_OUTPUT_FORMAT: Address: 4[3] The ADC output, by default, is in 2’s-complement mode. Programming the ADC_OUTPUT_FORMAT bit to 1 inverts the MSB, and the output becomes straight-offset binary mode. When the demodulation feature is enabled, only 2's complement format can be selected. ADC Reference Mode: Address 1[13] & 3[15] The following shows the register settings for the ADC internal reference mode and external reference mode. • 0x1[13] 0x3[15]=00: ADC internal reference mode, VREF_IN floating (pin M3) • 0x1[13] 0x3[15]=01: N/A • 0x1[13] 0x3[15]=10: N/A • 0x1[13] 0x3[15]=11: ADC external eference mode, VREF_IN = 1.4 V (pin M3) DIGITAL_GAIN_ENABLE: Address: 3[12] Setting this bit to 1 applies to each channel i the corresponding gain given by DIGTAL_GAIN_CHi <15:11>. The gain is given as 0dB + 0.2dB × DIGTAL_GAIN_CHi<15:11>. For instance, if DIGTAL_GAIN_CH5<15:11> = 3, channel 5 is increased by 0.6-dB gain. DIGTAL_GAIN_CHi <15:11> = 31 produces the same effect as DIGTAL_GAIN_CHi <15:11> = 30, setting the gain of channel i to 6 dB. DIGITAL_HPF_ENABLE • CH1-4: Address 21[0] • CH5-8: Address 33[0] DIGITAL_HPF_FILTER_K_CHX • CH1-4: Address 21[4:1] Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 33 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 • www.ti.com CH5-8: Address 33[4:1] This group of registers controls the characteristics of a digital high-pass transfer function applied to the output data, following Equation 1. y (n ) = 2k 2k + 1 éë x (n ) - x (n - 1) + y (n - 1)ùû (1) These digital HPF registers (one for the first four channels and one for the second group of four channels) describe the setting of K. The digital high pass filter can be used to suppress low frequency noise which commonly exists in ultrasound echo signals. The digital filter can significantly benefit near field recovery time due to T/R switch low frequency response. Table 6 shows the cut-off frequency vs K. Table 6. Digital HPF –1dB Corner Frequency vs K and Fs k 40 MSPS 50 MSPS 65 MSPS 2 2780 kHz 3480 kHz 4520 kHz 3 1490 kHz 1860 kHz 2420 kHz 4 770 kHz 960 kHz 1250 kHz LOW_FREQUENCY_NOISE_SUPPRESSION: Address: 1[11] The low-frequency noise suppression mode is especially useful in applications where good noise performance is desired in the frequency band of 0 to 1 MHz (around dc). Setting this mode shifts the low-frequency noise of the AFE5809 to approximately Fs/2, thereby moving the noise floor around dc to a much lower value. Register bit 1[11] is used for enabling or disabling this feature. When this feature is enabled, power consumption of the device will be increased slightly by approximate 1 mW/CH. LVDS_OUTPUT_RATE_2X: Address: 1[14] The output data always uses a DDR format, with valid/different bits on the positive as well as the negative edges of the LVDS bit clock, DCLK. The output rate is set by default to 1X (LVDS_OUTPUT_RATE_2X = 0), where each ADC has one LVDS stream associated with it. If the sampling rate is low enough, two ADCs can share one LVDS stream, in this way lowering the power consumption devoted to the interface. The unused outputs will output zero. To avoid consumption from those outputs, no termination should be connected to them. The distribution on the used output pairs is done in the following way: • Channel 1 and channel 2 come out on channel 3. Channel 1 comes out first • Channel 3 and channel 4 come out on channel 4. Channel 3 comes out first • Channel 5 and channel 6 come out on channel 5. Channel 5 comes out first • Channel 7 and channel 8 come out on channel 6. Channel 7 comes out first CHANNEL_OFFSET_SUBSTRACTION_ENABLE: Address: 3[8] Setting this bit to 1 enables the subtraction of the value on the corresponding OFFSET_CHx<9:0> (offset for channel i) from the ADC output. The number is specified in 2s-complement format. For example, OFFSET_CHx<9:0> = 11 1000 0000 means subtract –128. For OFFSET_CHx<9:0> = 00 0111 1111 the effect is to subtract 127. In effect, both addition and subtraction can be performed. Note that the offset is applied before the digital gain (see DIGITAL_GAIN_ENABLE). The whole data path is 2s-complement throughout internally, with digital gain being the last step. Only when ADC_OUTPUT_FORMAT = 1 (straight binary output format) is the 2scomplement word translated into offset binary at the end. SERIALIZED_DATA_RATE: Address: 3[14:13] Please see Table 4 for detail description. TEST_PATTERN_MODES: Address: 2[15:13] The AFE5809 can output a variety of test patterns on the LVDS outputs. These test patterns replace the normal ADC data output. The device may also be made to output 6 preset patterns: 1. Ramp: Setting Register 2[15:13]=111causes all the channels to output a repeating full-scale ramp pattern. The ramp increments from zero code to full-scale code in steps of 1LSB every clock cycle. After hitting the full-scale code, it returns back to zero code and ramps again. 34 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 2. Zeros: The device can be programmed to output all 0s by setting Register 2[15:13] = 110; 3. Ones: The device can be programmed to output all 1s by setting Register 2[15:13] = 100; 4. Deskew Patten: When 2[15:13] = 010; this mode replaces the 14-bit ADC output with the 01010101010101 word. 5. Sync Pattern: When 2[15:13] = 001, the normal ADC output is replaced by a fixed 11111110000000 word. 6. Toggle: When 2[15:13] = 101, the normal ADC output is alternating between 1's and 0's. The start state of ADC word can be either 1's or 0's. 7. Custom Pattern: It can be enabled when 2[15:13] = 011;. Users can write the required VALUE into register bits <CUSTOM PATTERN> which is Register 5[13:0]. Then the device will output VALUE at its outputs, about 3 to 4 ADC clock cycles after the 24th rising edge of SCLK. So, the time taken to write one value is 24 SCLK clock cycles + 4 ADC clock cycles. To change the customer pattern value, users can repeat writing Register 5[13:0] with a new value. Due to the speed limit of SPI, the refresh rate of the custom pattern may not be high. For example, 128 points custom pattern will take approximately 128 x (24 SCLK clock cycles + 4 ADC clock cycles). NOTE Only one of the above patterns can be active at any given instant. SYNC_PATTERN: Address: 10[8] By enabling this bit, all channels' test pattern outputs are synchronized. When 10[8] is set as 1, the ramp patterns of all 8 channels start simultaneously. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 35 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com VCA Register Map Table 7. VCA Register Map ADDRESS (DEC) ADDRESS (HEX) DEFAULT VALUE FUNCTION DESCRIPTION 51[0] 0x33[0] 0 RESERVED 0 51[3:1] 0x33[3:1] 0 LPF_PROGRAMMABILITY 000: 15 MHz, 010: 20 MHz, 011: 30 MHz, 100: 10 MHz. Please note: 0x3D[14], that is 5 MHz LPF, should be set as 0. 51[4] 0x33[4] 0 PGA_INTEGRATOR_DISABLE (PGA_HPF_DISABLE) 0: Enable 1: Disable offset integrator for PGA. See the explanation for the PGA integrator function in the APPLICATION INFORMATION section 51[7:5] 0x33[7:5] 0 PGA_CLAMP_LEVEL Low Noise mode: 53[11:10] = 00 000: –2 dBFS 010: 0 dBFS 1XX: Clamp is disabled Low power/Medium Power mode; 53[11:10] = 01/10 100: –2 dBFS 110: 0 dBFS 0XX: clamp is disabled Note: the clamp circuit makes sure that PGA output is in linear range. For example, at 000 setting, PGA output HD3 will be worsen by 3 dB at –2 dBFS ADC input. In normal operation, clamp function can be set as 000 in the low noise mode. The maximum PGA output level can exceed 2Vpp with the clamp circuit enabled. Note: in the low power and medium power modes, PGA_CLAMP is disabled for saving power if 51[7] = 0. . Note: Reg.61[15] should be set as 0; otherwise PGA_CLAMP_LEVEL is affected by Reg. 61[15]. 51[13] 0x33[13] 0 PGA_GAIN_CONTROL 0:24 dB; 1:30 dB. 52[4:0] 0x34[4:0] 0 ACTIVE_TERMINATION_ INDIVIDUAL_RESISTOR_CNTL SeeTable 9 Reg 52[5] should be set as '1' to access these bits 52[5] 0x34[5] 0 ACTIVE_TERMINATION_ INDIVIDUAL_RESISTOR_ENABLE 0: Disable; 1: Enable internal active termination individual resistor control 52[7:6] 0x34[7:6] 0 PRESET_ACTIVE_ TERMINATIONS 00: 50 Ω, 01: 100 Ω 10: 200 Ω 11: 400 Ω (Note: the device will adjust resistor mapping (52[4:0]) automatically. 50-Ω active termination is NOT supported in 12 dB LNA setting. Instead, '00' represents high impedance mode when LNA gain is 12 dB) 52[8] 0x34[8] 0 ACTIVE TERMINATION ENABLE 0: Disable; 1: Enable active termination 52[10:9] 0x34[10:9] 0 LNA_INPUT_CLAMP_SETTING 00: Auto setting, 01: 1.5 Vpp, 10: 1.15 Vpp and 11: 0.6 Vpp 52[11] 0x34[11] 0 RESERVED Set to 0 36 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Table 7. VCA Register Map (continued) ADDRESS (DEC) ADDRESS (HEX) DEFAULT VALUE 52[12] 0x34[12] 52[14:13] FUNCTION DESCRIPTION 0 LNA_INTEGRATOR_DISABLE (LNA_HPF_DISABLE) 0: Enable; 1: Disable offset integrator for LNA. See the explanation for this function in the following section 0x34[14:13] 0 LNA_GAIN 00: 18 dB; 01: 24 dB; 10: 12 dB; 11: Reserved 52[15] 0x34[15] 0 LNA_INDIVIDUAL_CH_CNTL 0: Disable; 1: Enable LNA individual channel control. See Register 57 for details 53[7:0] 0x35[7:0] 0 PDN_CH<7:0> 0: Normal operation; 1: Powers down corresponding channels. Bit7→CH8, Bit6→CH7…Bit0→CH1. PDN_CH will shut down whichever blocks are active depending on TGC mode or CW mode 53[8] 0x35[8] 0 RESERVED Set to 0 53[9] 0x35[9] 0 LOW_NF 0: Normal operation 1: Enable low noise figure mode for high impedance probes 53[11:10] 0x35[11:10] 0 POWER_MODES 00: Low noise mode; 01: Set to low power mode. At 30-dB PGA, total chain gain may slightly change. See typical characteristics 10:Set to medium power mode. At 30-dB PGA, total chain gain may slightly change. See typical characteristics 11: Reserved 53[12] 0x35[12] 0 PDN_VCAT_PGA 0: Normal operation; 1: Powers down VCAT (voltage-controlledattenuator) and PGA 53[13] 0x35[13] 0 PDN_LNA 0: Normal operation; 1: Powers down LNA only 53[14] 0x35[14] 0 VCA_PARTIAL_PDN 0: Normal operation; 1: Powers down LNA, VCAT, and PGA partially(fast wake response) 53[15] 0x35[15] 0 VCA_COMPLETE_PDN 0: Normal operation; 1: Power down LNA, VCAT, and PGA completely (slow wake response). This bit can overwrite 53[14]. 54[4:0] 0x36[4:0] 0 CW_SUM_AMP_GAIN_CNTL Select Feedback resistor for the CW Amplifier as per Table 9 54[5] 0x36[5] 0 CW_16X_CLK_SEL 0: Accept differential clock; 1: Accept CMOS clock 54[6] 0x36[6] 0 CW_1X_CLK_SEL 0: Accept CMOS clock; 1: Accept differential clock 54[7] 0x36[7] 0 RESERVED Set to 0 54[8] 0x36[8] 0 CW_TGC_SEL 0: TGC Mode; 1 : CW Mode Note : VCAT and PGA are still working in CW mode. They should be powered down separately through 53[12] 54[9] 0x36[9] 0 CW_SUM_AMP_ENABLE 0: Enable CW summing amplifier; 1: Disable CW summing amplifier Note: 54[9] is only effective in CW mode. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 37 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Table 7. VCA Register Map (continued) ADDRESS (DEC) ADDRESS (HEX) DEFAULT VALUE FUNCTION DESCRIPTION 54[11:10] 0x36[11:10] 0 CW_CLK_MODE_SEL 00: 16X mode; 01: 8X mode; 10: 4X mode; 11: 1X mode 55[3:0] 0x37[3:0] 0 CH1_CW_MIXER_PHASE 55[7:4] 0x37[7:4] 0 CH2_CW_MIXER_PHASE 55[11:8] 0x37[11:8] 0 CH3_CW_MIXER_PHASE 55[15:12] 0x37[15:12] 0 CH4_CW_MIXER_PHASE 56[3:0] 0x38[3:0] 0 CH5_CW_MIXER_PHASE 56[7:4] 0x38[7:4] 0 CH6_CW_MIXER_PHASE 56[11:8] 0x38[11:8] 0 CH7_CW_MIXER_PHASE 56[15:12] 0x38[15:12] 0 CH8_CW_MIXER_PHASE 57[1:0] 0x39[1:0] 0 CH1_LNA_GAIN_CNTL 57[3:2] 0x39[3:2] 0 CH2_LNA_GAIN_CNTL 0000→1111, 16 different phase delays, see Table 13 00: 18 dB; 01: 24 dB; 10: 12 dB; 11: Reserved REG52[15] should be set as '1' 57[5:4] 0x39[5:4] 0 CH3_LNA_GAIN_CNTL 57[7:6] 0x39[7:6] 0 CH4_LNA_GAIN_CNTL 57[9:8] 0x39[9:8] 0 CH5_LNA_GAIN_CNTL 57[11:10] 0x39[11:10] 0 CH6_LNA_GAIN_CNTL 57[13:12] 0x39[13:12] 0 CH7_LNA_GAIN_CNTL 57[15:14] 0x39[15:14] 0 CH8_LNA_GAIN_CNTL 59[3:2] 0x3B[3:2] 0 HPF_LNA 00: 100 kHz; 01: 50 kHz; 10: 200 kHz; 11: 150 kHz with 0.015 µF on INMx 59[6:4] 0x3B[6:4] 0 DIG_TGC_ATT_GAIN 000: 0-dB attenuation; 001: 6-dB attenuation; N: ~N×6 dB attenuation when 59[7] = 1 59[7] 0x3B[7] 0 DIG_TGC_ATT 0: disable digital TGC attenuator; 1: enable digital TGC attenuator 59[8] 0x3B[8] 0 CW_SUM_AMP_PDN 0: Power down; 1: Normal operation Note: 59[8] is only effective in TGC test mode. 59[9] 0x3B[9] 0 PGA_TEST_MODE 0: Normal CW operation; 1: PGA outputs appear at CW outputs 61[13] 0x3D[13] 0 V2I_CLAMP 0: Clamp disabled; 1: Clamp enabled at the V2I input. An additional voltage clamp at the V2I input. This limits the amount of overload signal the PGA sees. Note: this bit is supported by AFE5809 with date code later than 2014, that is date code >41XXXX. 61[14] 0x3D[14] 0 5MHz_LPF 0: 5MHz LPF disabled; 1: 5MHz LPF enabled. Suppress signals > 5 MHz or high order harmonics. The low pass filter Reg.51[3:1] needs to be set as 100, that is 10 MHz. Note: this bit is supported by AFE5809 with date code later than 2014, that is date code >41XXXX. 38 Submit Documentation Feedback 00: 18dB; 01: 24 dB; 10: 12 dB; 11: Reserved REG52[15] should be set as '1' Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Table 7. VCA Register Map (continued) ADDRESS (DEC) ADDRESS (HEX) DEFAULT VALUE FUNCTION DESCRIPTION 61[15] 0x3D[15] 0 PGA_CLAMP_-6dBFS 0: Disable the –6 dBFS clamp. PGA_CLAMP is set by Reg51[7:5]. 1: Enable the –6 dBFS clamp.PGA_CLAMP Reg51[7:5] should be set as 000 in the low noise mode or 100 in the low/medium power mode. In this setting, PGA output HD3 will be worsen by 3 dB at –6 dBFS ADC input. The actual PGA output is reduced to approximately 1.5 Vpp, about 2.5 dB below the ADC full scale input 2 Vpp . As a result, AFE5809’s low pass filter (LPF) is not saturated and it can suppress harmonic signals better at PGA output. Due to PGA output reduction, the ADC output dynamic range is impacted. Note: this bit is supported by AFE5809 with date code later than 2014, that is date code >41XXXX. VCA Register Description LNA Input Impedances Configuration (Active Termination Programmability) Different LNA input impedances can be configured through the register 52[4:0]. By enabling and disabling the feedback resistors between LNA outputs and ACTx pins, LNA input impedance is adjustable accordingly. Table 8 describes the relationship between LNA gain and 52[4:0] settings. The input impedance settings are the same for both TGC and CW paths. The AFE5809 also has 4 preset active termination impedances as described in 52[7:6]. An internal decoder is used to select appropriate resistors corresponding to different LNA gain. Table 8. Register 52[4:0] Description 52[4:0]/0x34[4:0] FUNCTION 00000 No feedback resistor enabled 00001 Enables 450-Ω feedback resistor 00010 Enables 900-Ω feedback resistor 00100 Enables 1800-Ω feedback resistor 01000 Enables 3600-Ω feedback resistor 10000 Enables 4500-Ω feedback resistor Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 39 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com The input impedance of AFE can be programmed through Register 52[8:0]. Each bit of Register 52[4:0] controls one active termination resistor. The below tables indicate the norminal impedance values when individual active termination resistors are selected. More details can be found in Active Termination. Table 9 shows the corresponding impedances under different Register 52[4:0] values, while Table 10 shows the Register 52[4:0] settings under different impedances. NOTE Table 9 and Table 10 show nominal input impedance values. Due to silicon process variation, the actual values can vary some. Table 9. Register 52[4:0] vs LNA Input Impedances 52[4:0]/0x34[4:0] 00000 00001 00010 00011 00100 00101 00110 00111 LNA:12dB High Z 150 Ω 300 Ω 100 Ω 600 Ω 120 Ω 200 Ω 86 Ω LNA:18dB High Z 90 Ω 180 Ω 60 Ω 360 Ω 72 Ω 120 Ω 51 Ω LNA:24dB High Z 50 Ω 100 Ω 33 Ω 200 Ω 40 Ω 66.67 Ω 29 Ω 52[4:0]/0x34[4:0] 01000 01001 01010 01011 01100 01101 01110 01111 LNA:12dB 1200 Ω 133 Ω 240 Ω 92 Ω 400 Ω 109 Ω 171 Ω 80 Ω LNA:18dB 720 Ω 80 Ω 144 Ω 55 Ω 240 Ω 65 Ω 103 Ω 48 Ω LNA:24dB 400 Ω 44 Ω 80 Ω 31 Ω 133 Ω 36 Ω 57 Ω 27 Ω 52[4:0]/0x34[4:0] 10000 10001 10010 10011 10100 10101 10110 10111 LNA:12dB 1500 Ω 136 Ω 250 Ω 94 Ω 429 Ω 111 Ω 176 Ω 81 Ω LNA:18dB 900 Ω 82 Ω 150 Ω 56 Ω 257 Ω 67 Ω 106 Ω 49 Ω LNA:24dB 500 Ω 45 Ω 83 Ω 31 Ω 143 Ω 37 Ω 59 Ω 27 Ω 52[4:0]/0x34[4:0] 11000 11001 11010 11011 11100 11101 11110 11111 LNA:12dB 667 Ω 122 Ω 207 Ω 87 Ω 316 Ω 102 Ω 154 Ω 76 Ω LNA:18dB 400 Ω 73 Ω 124 Ω 52 Ω 189 Ω 61 Ω 92 Ω 46 Ω LNA:24dB 222 Ω 41 Ω 69 Ω 29 Ω 105 Ω 34 Ω 51 Ω 25 Ω 40 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Table 10. LNA Input Impedances vs Register 52[4:0] Z (Ω) LNA:12dB LNA:18dB LNA:24dB Z (Ω) 25 11111 67 27 10111/011 11 69 29 00111/110 11 72 00101 150 00001 31 01011/100 11 73 11001 154 11110 33 00011 76 11111 171 01110 34 11101 80 01111 176 10110 36 01101 81 10111 37 10101 82 40 00101 83 200 00110 41 11001 86 00111 207 11010 44 01001 87 11011 222 10001 90 45 LNA:12dB 10010 01011 48 01111 94 10011 49 10111 100 00011 11101 102 00111/111 10 103 52 11011 105 55 01011 106 56 10011 57 59 LNA:12dB 144 00010 189 11100 01010 10010 257 00010 316 11100 360 00100 400 01100 429 10100 109 01101 500 111 10101 600 00100 10110 667 11000 00101 122 11001 61 11101 124 65 01101 00110 00110 11010 133 01001 136 10001 01100 01100 10100 300 01110 120 00100 11000 250 11100 10010 180 240 00010 LNA:24dB 01010 11110 10110 00011 LNA:18dB 10100 00001 01110 60 66.7 01010 10001 92 00001 01001 Z (Ω) 143 11010 11111 51 LNA:24dB 10101 46 50 LNA:18dB 11000 01000 10000 720 01000 900 10000 1200 01000 1500 10000 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 41 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Programmable Gain for CW Summing Amplifier Different gain can be configured for the CW summing amplifier through the register 54[4:0]. By enabling and disabling the feedback resistors between the summing amplifier inputs and outputs, the gain is adjustable accordingly to maximize the dynamic range of CW path. Table 11 describes the relationship between the summing amplifier gain and 54[4:0] settings. Table 11. Register 54[4:0] Description 54[4:0]/0x36[4:0] FUNCTION 00000 No feedback resistor 00001 Enables 250-Ω feedback resistor 00010 Enables 250-Ω feedback resistor 00100 Enables 500-Ω feedback resistor 01000 Enables 1000-Ω feedback resistor 10000 Enables 2000-Ω feedback resistor Table 12. Register 54[4:0] vs Summing Amplifier Gain 54[4:0]/0x36[4:0] CW I/V Gain 54[4:0]/0x36[4:0] CW I/V Gain 54[4:0]/0x36[4:0] CW I/V Gain 54[4:0]/0x36[4:0] CW I/V Gain 00000 00001 00010 00011 00100 00101 00110 00111 N/A 0.50 0.50 0.25 1.00 0.33 0.33 0.20 01000 01001 01010 01011 01100 01101 01110 01111 2.00 0.40 0.40 0.22 0.67 0.29 0.29 0.18 10000 10001 10010 10011 10100 10101 10110 10111 4.00 0.44 0.44 0.24 0.80 0.31 0.31 0.19 11000 11001 11010 11011 11100 11101 11110 11111 1.33 0.36 0.36 0.21 0.57 0.27 0.27 0.17 Programmable Phase Delay for CW Mixer Accurate CW beamforming is achieved through adjusting the phase delay of each channel. In the AFE5809, 16 different phase delays can be applied to each LNA output; and it meets the standard requirement of typical 1 λ ultrasound beamformer, that is 16 beamformer resolution. Table 11 describes the relationship between the phase delays and the register 55 and 56 settings. Table 13. CW Mixer Phase Delay vs Register Settings CH1 - 55[3:0], CH2 - 55[7:4], CH3 - 55[11:8], CH4 - 55[15:12], CH5- 56[3:0], CH6 - 56[7:4], CH7 - 56[11:8], CH8 - 56[15:12] CHX_CW_MIXER_PHASE PHASE SHIFT 0000 0001 0010 0011 0100 0101 0110 0111 0 22.5° 45° 67.5° 90° 112.5° 135° 157.5° CHX_CW_MIXER_PHASE 1000 1001 1010 1011 1100 1101 1110 1111 PHASE SHIFT 180° 202.5° 225° 247.5° 270° 292.5° 315° 337.5° 42 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 SPI Interface for Demodulator Demodulator is enabled after software or hardware reset. It can be disabled by setting the LSB of register 0x16 as '1'. This is done using the ADC SPI interface, that is SPI_DIG_EN = 1. The demodulator SPI interface is independent from the ADC/VCA SPI interface as shown in Figure 65: Figure 65. SPI Interface in the AFE5809 To access the specific demodulator registers: 1. SPI_DIG_EN pin is required to be set as '0' during SPI transactions to demodulator registers. Meanwhile ADC SEN needs to be set as '0' during demodulator SPI programming. 2. SPI register address is 8 bits and is made of 2 subchip select bits and 6 register address bits. SPI register data is 16bits. Table 14. Register Address Bit Description Bit7 Bit6 Bit 5:0 SCID1_SEL SCID0_SEL Register Address <5:0> 3. SCID0_SEL enables configuration of channels 1-4. 'SCID1_SEL' enables configuration of channels 5-7. When performing Demodulator SPI write transactions, these SCID bits can be individually or mutually used with a specific register address. 4. Register configuration is normally shared by both subchips (both 'SCID' bits should be set as '1'). An exception to this rule would be the DC OFFSET registers (0x14-0x17) for which specific channel access is expected. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 43 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 ADC.1 ADC.2 ADC.3 ADC.4 ADC.5 ADC.6 ADC.7 ADC.8 www.ti.com LVDS.1 CH.A LVDS.2 CH.B CH.C Sub-Chip 0 LVDS.3 LVDS.4 CH.D LVDS.5 CH.A LVDS.6 CH.B Sub-Chip 1 CH.C CH.D LVDS.7 LVDS.8 Figure 66. Each of Two Sub-chips Supports 4 Channels. Each of Two Demodulators has 4 Channels Named as A, B, C, D 5. Demodulator register readout follows the following procedures: – Write '1' to register 0x0[1]; pin SPI_DIG_EN should be '0' while writing. This is the readout enable register for demodulator. – Write '1' to register 0x0[1], pin SPI_DIG_EN should be '1' while writing. This is the readout enable register for ADC and VCA. – Set SPI_DIG_EN as '0' and write anything to the register whose stored data needs to be known. Device finds the address of the register and sends its stored data at the SDOUT pin serially. NOTE After enabling the register 0x0[1] REGISTER_READOUT_ENABLE, data can't be written to the register (whose data needs to be known) but stored data would come serially at the SDOUT pin. – To disable the register readout, first write '0' to register 0x0[1] while SPI_DIG_EN is '1'; then write '0' to register 0x0[1] while SPI_DIG_EN is '0'. 44 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Table 15. Digital Demodulator Register Map Note: 1. When programming the SPI, 8-bit address is required. The below table and following sections only list the Add_Bit5 to Add_Bit0. The Add_Bit7 = SCID1_SEL and Add_Bit6 = SCID0_SEL need to be appended as 11, 10, or 01, which determines either SubChip1 or SubChip0 is being programmed. If SCID1_SEL,SCID0_SEL = 11, then both subchips get written with the same register value. Please see Table 14. 2. Reserved register bits must be programmed based on their descriptions. 3. Unlisted register bits must be programmed as 0s. REGISTER NAME ADD(HEX) BIT[5:0] ADD(DEC) BIT[5:0] DEFAULT DESCRIPTION MANUAL_TX_TRIG 00[2] 00[2] 0 1: generate internal tx_trig (self clear, Write Only). This is an alternative for TX_SYNC hardware pulse. REGISTER_READOUT_E NABLE 00[1] 00[1] 0 1:enables readout of register at SDOUT pin (Write Only) CHIP_ID 01[4:0] 01[4:0] 0 Unique Chip ID OUTPUT_MODE 02[15:13] 02[15:13] 0 000-normal operation 011- custom pattern (set by register 05). NOTE: LSB always comes out first no matter 0x04[4]=0 or 1 111- chipID + ramp test pattern. ChipID (5 bit) and Sub-chip information (3 bit) are the 8 LSBs and the ramp pattern is in the rest MSBs. (0x0A[9] = 1) SERZ_FACTOR 03[14:13] 03[14:13] 11 Serialization factor (output rate) 00-10x 01-12x 10-14x 11-16x. Note: this register is different from the ADC SERIALIZED_DATA_RATE. The demod and ADC serilization factors must be matched. Please see LVDS Serialization Factor. OUTPUT_RESOLUTION 03[11:9] 03[11:9] 0 Output resoluiton of the demodulator. It refers to the ADC resolution when the demodulator is bypassed. 100-16 bit (DEMOD only) 000-14 bit 001-13 bit 010-12 bit MSB_FIRST 04[4] 04[4] 0 0-LSB first; 1-MSB first. This bit will not affect the test mode: customer pattern, that is 02[15:13] = 011B. Note: in the CUSTOM_PATTERN mode, the output is always set as LSB first regardless of this bit setting. CUSTOM_PATTERN 05[15:0] 05[15:0] 0000 Custom data pattern for LVDS (0x02[15:13] = 011) COEFF_MEM_ADDR_WR 06[7:0] 06[7:0] 0 Write address offset to coefficient memory (auto increment) COEFF_BANK 07[111:0] 07[111:0] --- Writes chunks of 112 bits to the coefficient memory. This RAM does not have default values, so it is necessary to write required values to the RAM. TI recommends to configure the RAM before other registers. PROFILE_MEM_ADDR_W R 08[4:0] 08[4:0] 0 Write address offset to profile memory (auto increment) PROFILE_BANK 09 [63:0] 09 [63:0] --- Writes chunks of 64 bits to the profile memory (effective 62 bits since two LSBs are ignored). This RAM does not have default values, so it is necessary to write required values to the RAM. TI recommends to configure the RAM before other registers. RESERVED 0A[15] 10[15] 0 Must set to 0. MODULATE_BYPASS 0A[14] 10[14] 0 Arrange the demodulator output format for I/Q data. Please see Table 13. DEC_SHIFT_SCALE 0A[13] 10[13] 0 0- no additional shift applied to the decimation filter output. 1-shift the decimation filter output by 2 bits additionally, that is apply 12dB additional digital gain. RESERVED 0A[12] 10[12] 1 Must set to 1. OUTPUT_CHANNEL_SEL 0A[11] 10[11] 0 Swap channel pairs. It is used in 4 LVDS bypass configuration to select which of the two possible data streams to pass on. See Table 13. SIN_COS_RESET_ON_TX _TRIG 0A[10] 10[10] 1 0-Continuous phase 1-Reset down convertion phase on TX_TRIG FULL_LVDS_MODE 0A[9] 10[9] 0 0-Use 4 LVDS lines (1,3,5,7) 1-Use 8 LVDS lines (1-8) Note: 4 LVDS mode valid only for decimation factors ≥4. Please see Table 17. RESERVED 0A[8:5] 10[8:5] 0 Must set to 0. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 45 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Table 15. Digital Demodulator Register Map (continued) Note: 1. When programming the SPI, 8-bit address is required. The below table and following sections only list the Add_Bit5 to Add_Bit0. The Add_Bit7 = SCID1_SEL and Add_Bit6 = SCID0_SEL need to be appended as 11, 10, or 01, which determines either SubChip1 or SubChip0 is being programmed. If SCID1_SEL,SCID0_SEL = 11, then both subchips get written with the same register value. Please see Table 14. 2. Reserved register bits must be programmed based on their descriptions. 3. Unlisted register bits must be programmed as 0s. REGISTER NAME ADD(HEX) BIT[5:0] ADD(DEC) BIT[5:0] DEFAULT DESCRIPTION RESERVED 0A[4] 10[4] 0 Must set to 1. DEC_BYPASS 0A[3] 10[3] 0 0-Enable decimation filter 1-Bypass decimation filter DWN_CNV_BYPASS 0A[2] 10[2] 0 0-Enable down conversion block 1-Bypass down conversion block. Note: the decimation filter still can be used when the down conversion block is bypassed. RESERVED 0A[1] 10[1] 1 Must be set as 1. DC_REMOVAL_BYPASS 0A[0] 10[0] 0 0-Enable DC removal block 1-Bypass DC removal block SYNC_WORD 0B[15:0] 11[15:0] 0x2772 LVDS sync word. When MODULATE_BYPASS = 1, there is no sync word output. PROFILE_INDX 0E[15:11] 14[15:11] 0 Profile word selector. The Profile Index register is a Special 5 bit data register. Read value still uses 16 bit convention which means data will be available on LSB 0e[4:0]) DC_REMOVAL_1_5 14[13:0] 20[13:0] 0 54[13:0]→DC offset for channel 1, SCID1_SEL,SCID0_SEL=01 94[13:0]→DC offset for channel 5, SCID1_SEL,SCID0_SEL=10 Note: considering the CH to CH DC offset variation, the offset value has to be set individually. Therefore, SCID1_SEL,SCID0_SEL should not be set as 11. DC_REMOVAL_2_6 15[13:0] 21[13:0] 0 55[13:0]→DC offset for channel 2, SCID1_SEL,SCID0_SEL=01 95[13:0] →DC offset for channel 6, SCID1_SEL,SCID0_SEL=10 Note: considering the CH to CH DC offset variation, the offset value has to be set individually. Therefore SCID1_SEL,SCID0_SEL should not be set as 11. DC_REMOVAL_3_7 16[13:0] 22[13:0] 0 56[13:0] →DC offset for channel 3, SCID1_SEL,SCID0_SEL=01 96[13:0] →DC offset for channel 7, SCID1_SEL,SCID0_SEL=10 Note: considering the CH to CH DC offset variation, the offset value has to be set individually. Therefore SCID1_SEL,SCID0_SEL should not be set as 11. DC_REMOVAL_4_8 17[13:0] 23[13:0] 0 57[13:0] →DC offset for channel 4, SCID1_SEL,SCID0_SEL=01 97[13:0] →DC offset for channel 8, SCID1_SEL,SCID0_SEL=10 Note: considering the CH to CH DC offset variation, the offset value has to be set individually. Therefore SCID1_SEL,SCID0_SEL should not be set as 11. DEC_SHIFT_FORCE_EN 1D[7] 29[7] 0 0-Profile vector specifies the number of bit to shift for the decimation filter output. 1-Reg.1D[6:4] specifies the number of bit to shift for the decimation filter output. DEC_SHIFT_FORCE 1D[6:4] 29[6:4] 0 Specify that the decimation filter output is right shifted by (20-N) bit, N = 0x1D[6:4]. N = 0, minimal digital gain; N = 7 maximal digital gain; additional 12-dB digital gain can be applied by setting DEC_SHIFT_SCALE = 1,that is 0x0A[13] = 1; TM_COEFF_EN 1D[3] 29[3] 0 1-set coefficient output test mode TM_SINE_EN 1D[2] 29[2] 0 1-set sine output mode; the sine waveform specifications can be configured through register 0x1E. RESERVED 1D[1] 29[1] 0 MUST set to 0 RESERVED 1D[0] 29[0] 0 MUST set to 0 TM_SINE_DC 1E[15:9] 30[15:9] 0 7 bit signed value for sine wave DC offset control. TM_SINE_AMP 1E[8:5] 30[8:5] 0 4 bit unsigned value, controlling the sin wave amplitude (powers of two), from unity to the full scale of 14 bit, including saturation. 0: no sine (only DC). TM_SINE_STEP 1E[4:0] 30[4:0] 0 5 bit unsigned value, controlling the sin wave frequency with resolution of Fs/26, which is 0.625MHz for 40 MHz ADC clock. 46 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Table 15. Digital Demodulator Register Map (continued) Note: 1. When programming the SPI, 8-bit address is required. The below table and following sections only list the Add_Bit5 to Add_Bit0. The Add_Bit7 = SCID1_SEL and Add_Bit6 = SCID0_SEL need to be appended as 11, 10, or 01, which determines either SubChip1 or SubChip0 is being programmed. If SCID1_SEL,SCID0_SEL = 11, then both subchips get written with the same register value. Please see Table 14. 2. Reserved register bits must be programmed based on their descriptions. 3. Unlisted register bits must be programmed as 0s. REGISTER NAME ADD(HEX) BIT[5:0] ADD(DEC) BIT[5:0] DEFAULT DESCRIPTION MANUAL_COEFF_START _EN 1F[15] 31[15] 0 0: The starting address of the coefficient RAM is set by the profile vector. that is the starting address is set manually. 1: The starting address of the coefficient RAM is set by the register 0x1F[14:7]. MANUAL_COEFF_START _ADDR 1F[14:7] 31[14:7] 0 When 0x1F[15] is set, the starting address of coefficient RAM is set by these 8 bits. MANUAL_DEC_FACTOR_ EN 1F[6] 31[6] 0 0: The decimation factor is set by profile vector. 1: The decimation factor is set by the register 0x1F[5:0]. MANUAL_DEC_FACTOR 1F[5:0] 31[5:0] 0 When 0x1F[6] is set, the decimation factor is set by these 6 bits. Note: it is from 1 to 32. MANUAL_FREQ_EN 20[0] 32[0] 0 0: The down convert frequency is set by profile vector. 1: The down convert frequency is set by the register 0x21[15:0]. MANUAL_FREQ 21[15:0] 33[15:0] 0 When 0x20[0] is set, the value of manual down convert frequency is calculated as N x Fs / 216 Digital Demodulator Register Description Table 16. Configuring Data Output: Register Name SPI Address SERZ_FACTOR 0x03[14:13] OUTPUT_RESOLUTION 0x03[11:9] MSB_FIRST 0x04[4] OUT_MODE 0x02[15:13] CUSTOM_PATTERN 0x05[15:0] OUTPUT_CHANNEL_SEL 0x0A[11] MODULATE_BYPASS 0x0A[14] FULL_LVDS_MODE 0x0A[9] spacer 1. Serializer Configuration: – Serialization Factor 0x03[14:13]: It can be set using demodulator register SERZ_FACTOR. Default serialization factor for the demodulator is 16x. However, the actual LVDS clock speed can be set by the serialization factor in the ADC SPI interface as well; the ADC serialization factor is adjusted to 14x by default. Therefore, it is necessary to sync these two settings when demodulator is enabled, that is set the ADC register 0x03[14:13]=01. – Output Resolution 0x03[11:9]: In the default setting, it is 14 bit. The demodulator output resolution depends on the decimation factor. 16 bit resolution can be used when higher decimation factor is selected. 2. Channel Selection: – Using register MODULATE_BYPASS 0x0A[14], channel output mode can be selected as IQ modulated or single channel I or Q output. – Channel output is also selected using registers OUTPUT_CHANNEL_SEL 0x0A[11] and FULL_LVDS_MODE 0x0A[9] and decimation factor. – Each of two demodulator subchips in a device has 4 channels named as A, B, C, D. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 47 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com NOTE After decimation, the LVDS FCLK rate keeps the same as the ADC sampling rate. Considering the reduced data amount, zeros will be appended after I and Q data and ensure the LVDS data rate matches the LVDS clock rate. For detailed information about channel multiplexing, see Table 17. In the table, A.I refers to CHA In-phase output, and A.Q refers to CHA Quadrature output. For example, M=3, the valid data output rate is Fs/3 for both I and Q channels, that is 2Fs/3 bandwidth is occupied. The left Fs/3 bandwidth is then filled by M-2 zeros. As a result, the demod LVDS output data are A.I, A.Q, 0, A.I A.Q 0 after SYNC_WORD, FCLK = Fs and DCLK = Fs × 8. When two ADC CHs' data are transferred by one LVDS lane, M-4 zeros are filled after A.I, A.Q, B.I and B.Q. Please see more details in Table 17 and Figure 67. Table 17. Channel Selection Decimation Factor (M) Modulate Bypass Output Full LVDS Decimation Channel Select Mode Factor M LVDS Output Description LVDS1: A.I, A.Q, (zeros) LVDS2: B.I, B.Q, (zeros) M<4 LVDS3: C.I, C.Q, (zeros) 0 LVDS4: D.I, D.Q, (zeros) M≥4 0 LVDS1: A.I, A.Q, B.I, B.Q, (zeros) LVDS2: idle LVDS3: C.I, C.Q, D.I, D.Q, (zeros) LVDS4: idle LVDS1: A.I, A.Q, (zeros) 1 LVDS2: B.I, B.Q, (zeros) X LVDS3: C.I, C.Q, (zeros) LVDS4: D.I, D.Q, (zeros) M≥2 LVDS1: B.I, B.Q, (zeros) 0 LVDS2: A.I, A.Q, (zeros) M<4 LVDS3: D.I, D.Q, (zeros) LVDS4: C.I, C.Q, (zeros) 0 LVDS1: B.I, B.Q, A.I, A.Q, (zeros) LVDS2: idle M≥4 1 LVDS3: D.I, D.Q, C.I, C.Q, (zeros) LVDS4: idle LVDS1: B.I, B.Q, (zeros) 1 LVDS2: A.I, A.Q, (zeros) X LVDS3: D.I, D.Q, (zeros) LVDS4: C.I, C.Q, (zeros) LVDS1: A.I; Note: the same A.I is repeated by M times. 0 M≥2 X X LVDS2: A.Q; Note: the same A.Q is repeated by M times. LVDS3: C.I; Note: the same C.I is repeated by M times. LVDS4: C.Q; Note: the same C.Q is repeated by M times. 1 LVDS1: B.I; Note: the same B.I is repeated by M times. 1 X X LVDS2: B.Q; Note: the same B.Q is repeated by M times. LVDS3: D.I; Note: the same D.I is repeated by M times. LVDS4: D.Q; Note: the same D.Q is repeated by M times. M=1 0 0 X 1 LVDS1: A.I; LVDS2: B.I; LVDS3: C.I; LVDS4: D.I M=1 0 1 X 1 LVDS1: B.I; LVDS2: A.I; LVDS3: D.I; LVDS4: C.I M=1 1 0 X 1 LVDS1: A.I; LVDS2: A.Q; LVDS3: C.I; LVDS4: C.Q M=1 1 1 X 1 LVDS1: B.I; LVDS2: B.Q; LVDS3: D.I; LVDS4: D.Q Note: This table refers to individual demodulator subchip, which has 4 LVDS outputs, that is LVDS1~4; and 4 Input CHs, that is CH.A to CH.D. Please see Figure 66. 48 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 ADC CLK OUTPUT DATA M=3 M=4, 1 LVDS Lane per ADC CH M=4, 1 LVDS Lane per 2 ADC CHs M=5, 1 LVDS Lane per 2 ADC CHs 0000 SYNC WORD A.I A.Q 0000 A.I A.Q 0000 SYNC WORD A.I A.Q 0000 0000 A.I 0000 SYNC WORD A.I A.Q B.I B.Q A.I 0000 SYNC WORD A.I A.Q B.I B.Q 0000 Figure 67. Output Data Format at M=3~5 3. Output Mode: – Using register OUT_MODE, ramp pattern and custom pattern can be enabled. – Custom Pattern: In case of custom pattern, custom pattern value can be set using register CUSTOM_PATTERN. Please Note: LSB always comes out first no matter 0x04[4] = 0 or 1, that is MSB_FIRST = 0 or 1. – Ramp Pattern: Demodulator generated ramp pattern includes information of chip_id as well. 8 MSB (that is Data[15..8]) bits are ramp pattern. Next 5 bits (that is Data[3..7]) gives value of chip ID. Data[2] corresponds to subchip ID, 0 or 1; Data[1:0] are filled with zeros. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 49 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Table 18. DC Removal Block Register Name SPI Address DC_REMOVAL_BYPASS 0x0A[0] DC_REMOVAL_1_5 0x14[13:0] DC_REMOVAL_2_6 0x15[13:0] DC_REMOVAL_3_7 0x16[13:0] DC_REMOVAL_4_8 0x17[13:0] spacer • DC removal block can be bypassed using the register bit DC_REMOVAL_BYPASS. • DC removal is designed to be done manually. • Manual DC offset removal: Registers DC_REMOVAL_1_5, DC_REMOVAL_2_6, DC_REMOVAL_3_7, DC_REMOVAL_4_8 can be used to give manual offset. Value should be given in 2’s compliment format. In case of these registers, SCID values should be given accordingly (check section "SPI interface for Demodulator" for more information). Example: For DC offset of channel 5, address of the register would be 0x91 (in hex). Here SCID0 is '0' and SCID1 is '1'. Table 19. Down Conversion Block Register Name SPI Address DWN_CNV_BYPASS 0x0A[2] SIN_COS_RESET_ON_TX_TRIG 0x0A[10] MANUAL_FREQ_EN 0x20 [0] MANUAL_FREQ 0x21[15:0] spacer • Down Conversion Block can be bypassed using register DWN_CNV_BYPASS. • Down Conversion Frequency can be given using “Down Conversion Frequency (f)” parameter of Profile Vector. Alternatively manual registers MANUAL_FREQ_EN and MANUAL_FREQ can be used to provide down conversion frequency. • Down Conversion frequency (f): 'f' can be set with resolution Fs / 216. (Where Fs is the sampling frequency). An integer value of "216f / Fs" is to be given to the profile vector or respective register • Down conversion signal can be configured to be reset at each TX_TRIG pulse. This facility can be enabled using SIN_COS_RESET_ON_TX_TRIG. Table 20. Decimation Block 50 Register Name SPI Address DEC_BYPASS 0x0A[3] MANUAL_DEC_FACTOR_EN 0x1F [6] MANUAL_DEC_FACTOR 0x1F[5:0] MANUAL_COEFF_START_EN 0x1F[15] MANUAL_COEFF_START_ADDR 0x1F[14:7] DEC_SHIFT_FORCE_EN 0x1D[7] DEC_SHIFT_FORCE 0x1D[6:4] DEC_SHIFT_SCALE 0x0A[13] Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com • • • • • • SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Decimation block can be bypassed using register DEC_BYPASS. Decimation Factor: This can be set using "Decimation Factor (M)" parameter of profile vector. Alternatively it can be set using registers MANUAL_DEC_FACTOR_EN and MANUAL_DEC_FACTOR. Filter Coefficients: Filter coefficients should be written to coefficient RAM (check Coefficient RAM section above). Format of filter coefficient is 2’s complement. Its address pointer should be given in profile vector or alternatively registers MANUAL_COEFF_START_EN and MANUAL_COEFF_START_ADDR can be used. Filter Digital Gain: Decimation block takes 14 bit input data and 14 bit input coefficients and gives 36 bit output internally. While implementing this FIR filter, after multiplication and addition, the 36 bit internal filter output should be scaled approximately to make final demod output as 16 bit, that is applying digital gain or attenuation. Filter gain or attenuation depends on two parameters: Decimation Shift Scale and Gain Compensation factor. Decimation Shift Scale can be chosen using register DEC_SHIFT_SCALE. Gain Compensation factor can be given to "Gain Compensation Factor (G)" parameter of Profile Vector; or can be given using registers DEC_SHIFT_FORCE_EN and DEC_SHIFT_FORCE. The internal 36 bit filter output is right shifted by N bits, where N equals to – 20-G when Dec_Shift_Scale = 0. – 20-G-2 when Dec_Shift_Scale = 1. The minimal gain occurs when G=0 and DEC_SHIFT_SCALE=0. The total scaling range can be a factor of 29, that is approximately 54 dB. Table 21. Test Modes Register Name SPI Address TM_SINE_DC 0x1E[15:9] TM_SINE_AMP 0x1E[8:5] TM_SINE_STEP 0x1E[4:0] TM_SINE_EN 0x1D[2] TM_COEFF_EN 0x1D[3] spacer 1. Sine test mode: The normal ADC output can be replaced by: xn = C + 2k sin( – – – pNn ) 25 (2) N is 5 bit unsigned value, controlling the sin wave frequency with resolution of FS / 26, which is 0.625 MHz for 40 MHz ADC clock. k is 4 bit unsigned value, controlling the wave amplitude, from unity to the full scale of 14 bit, including saturation. C is 7 bit signed value for DC offset control. The controlling values fit into one 16-bit register. This test pattern shall allow testing of demodulation, decimation filter, DC removal, gain control, and so on. 2. Coefficient output test mode: – The Input to the decimating filter can be replaced with a sequence of "one impulse" and "zero" samples, where "one impulse(that is 0x4000)" is followed by (16 x M) "zeros (that is 0 × 0000)". – This mode is useful to check decimation filter coefficients. – This mode can be enabled using register TM_COEFF_EN. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 51 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Profile RAM and Coefficient RAM Writing data to Profile RAM and Coefficient RAM is similar to registers. Both RAMs do not get reset after resetting the device. RAM does not have default values, so it is necessary to write required values to RAM. RAM address values needs to be given to pointer register that points to the location wherever data needs to be written. Since both RAMs are part of Demodulator, SPI_DIG_EN should be low while writing. TI recommends to program the RAMs before configuring other registers. Table 22. Profile Related Registers Register Name SPI Address PROFILE_MEM_ADDR_WR 0x08[4:0] PROFILE_BANK 0x09[63:0] PROFILE_INDEX 0x0E[15:11] spacer • Profile RAM can store up to 32 Vectors/Profiles. Each Vector/Profile has 64 bits. • Pointer Value should be given to the register PROFILE_MEM_ADDR_WR before writing to RAM. • The 64 bits of each Vector/Profile are arranged as follows: Table 23. Profile RAM Name of parameter Address Description Reserved RAM[63:50] Set to 0 Reserved RAM[49:36] Set to 0 Pointer to Coeff Memory (P)* RAM[35:28] A pointer to filter coefficient memory (8 bit), pointing to 8coefficients blocks. The relevant coefficients will start from address P*8 in the coefficients memory and will continue for M blocks. Decimation Factor (M)* RAM[27:22] Decimation Factor for Decimation Block Down Conversion Frequency (f)* RAM[21:6] Down Conversion frequency for Down Conversion Block Reserved RAM[5] Set to 0 Gain Compensation Factor (G) * RAM[4:2] Gain Compensation Factor Parameter for Decimation block *Alternate manual register is available • 2 LSB’s (that is RAM[1:0]) are ignored and can be set as 0s. • A particular profile vector can be activated using register PROFILE_INDEX. Address pointing to the location of particular vector is to be given in PROFILE_INDEX. Table 24. Coefficient RAM Register Name SPI Address COEFF_MEM_ADDR_WR 0x06[7:0] COEFF_BANK 0x07[111:0] MANUAL_COEFF_START_ADDR 0x1F[14:7] MANUAL_COEFF_START_EN 0x1F[15] spacer • Coefficient RAM can store up to 256 coefficient memory blocks. Size of each block is 112 bits. • Pointer Value should be given to the register COEFF_MEM_ADDR_WR before writing to RAM. • Write 112 bits to SPI address 0xC7 (MSB first). Each coefficient memory block consists of 8 14bit coefficients which are aligned in the following manner: (Coefficient order from right to left. Bit order from right to left). • Note: the coefficients are in 2's complement format. 52 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Table 25. Coefficient RAM Mapping Note that SPI serialization is done from left to right (0xCoeff 7[13] first and 0xCoeff 0[0] last) Coeff 7[13:0] Coeff 6[13:0] Coeff 5[13:0] Coeff 4[13:0] Coeff 3[13:0] Coeff 2[13:0] Coeff 1[13:0] Coeff 0[13:0] 111:98 97:84 83:70 69:56 55:42 41:28 27:14 13:0 spacer • Since Decimation block uses 16 x M tap FIR filter and filter coefficients are symmetric, only half (that is 8 × M) filter coefficients are necessary to be stored (M is the decimation factor). Each 8 coefficient block that is written to the memory represents a single phase of a polyphase filter. Therefore; the relation between the filter coefficients Cn and their index (i,j) in the coefficients memory is given by: n = M x (1 + I) − (1 + j) (3) where I is the index in the coefficients block, from 0 to 7, and j is the block index, from 0 to (M – 1) . Example for M = 4 Table 26. Coefficient RAM Mapping j\I 7 6 5 4 3 2 1 0 0 Coeff 31 Coeff 27 Coeff 23 Coeff 19 Coeff 15 Coeff 11 Coeff 7 Coeff 3 1 Coeff 30 Coeff 26 Coeff 22 Coeff 18 Coeff 14 Coeff 10 Coeff 6 Coeff 2 2 Coeff 29 Coeff 25 Coeff 21 Coeff 17 Coeff 13 Coeff 9 Coeff 5 Coeff 1 3 Coeff 28 Coeff 24 Coeff 20 Coeff 16 Coeff 12 Coeff 8 Coeff 4 Coeff 0 spacer • Coefficient start address can be given using "Pointer to Coeff Memory (P)" parameter of profile RAM. Alternatively start address can be given using register MANUAL_COEFF_START_ADDR. (While using this register, register enable bit MANUAL_COEFF_START_EN should be set to '1'). Register Readout While reading data from Demodulator registers procedure: • Write '1' to register 0x0[1]; pin SPI_DIG_EN should be '0' while writing, that is it is the readout enable register for demodulator. • Write '1' to register 0x0[1]; pin SPI_DIG_EN should be '1' while writing, that is it is the readout enable register for VCA and ADC. • Put SPI_DIG_EN 'low' and write anything to the register whose stored data needs to be known. Device finds the address of the register and sends its stored data at the SDOUT pin serially. Note: After enabling the register 0x0[1] REGISTER_READOUT_ENABLE, register data can not be written to the register, whose data needs to be known. The stored data would come serially at the SDOUT pin. • To disable the register readout, first write '0' to register 0x0[1] while SPI_DIG_EN is high; then write '0' to register 0x0[1] while SPI_DIG_EN is low. LVDS Serialization Factor Default serialization factor for the demodulator is 16×. However, the actual LVDS clock speed is set by the serialization factor in the ADC SPI interface and is adjusted to 14× serialization by default. It is therefore necessary to sync these two settings when demodulator is enabled. When using the default demodulator serialization factor, register 0x03[14:13] in the ADC SPI interface should be set to '01'. For RF mode (passing 14 bits only), demodulator serialization factor can be changed to 14x by setting demodulator register 0xC3[14:13] to '10'. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 53 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Programming the Coefficient RAM 1. Set SPI address 0xC6[7:0] with the base address, for example 0x0000. 0xC6 means both demodulator subchips are enabled. 2. Write 112 bits to SPI address 0xC7 (MSB first). Each coefficient memory word consists of eight 14-bit coefficients which are aligned in the following manner. Note: the coefficients are in 2's complement format. Figure 68. Coefficient Order from Right to left. Bit Order from Right to Left Coeff 7[13:0] 111:98 Coeff 6[13:0] 97:84 Coeff 5[13:0] 83:70 Coeff 4[13:0] 69:56 Coeff 3[13:0] 55:42 Coeff 2[13:0] 41:28 Coeff 1[13:0] 27:14 Coeff 0[13:0] 13:0 NOTE Note that SPI serialization is done from left to right (Coeff 7[13] first and Coeff 0[0] last). 3. Repeat step 2 for the following coefficient bulk entries (the address in register 0xC6 auto increments). Programming the Profile RAM 1. Set SEN and SPI_DIG_EN as '0'. 2. Set SPI address 0xC8[4:0] with the base address, for example 0x0000. 0xC8 means both demodulator subchips are enabled. 3. The 64 profile vector bits are arranged as following: – RAM[63:50] = 0 Reserved – RAM[49:36] = 0 Reserved – RAM[35:28]- Pointer to coeff memory (8 bit) – RAM[27:22]- decimation factor (6bit) – RAM[21:6]- Demodulation frequency (16 bit) – RAM[5] = 0 – RAM[4:2]- Gain compensation factor (3 bit) – RAM[1:0]- 2 LSBs are ignored, can be set as 0s. 4. Write the above 64 bits to SPI address 0xC9. MSB first. 5. Repeat step 3 and 4 for the following profile entries (the address in register 0xC8 will auto increment). 6. Set SEN and SPI_DIG_EN as '1'. Procedure for Configuring Next Vector 1. Write profile index (5 bits) to SPI address 0xCE[15:11]. 0xCE means both demodulator subchips are enabled. RF Mode RF mode allows for the streaming of ADC data through the demodulator to the LVDS. Note: test pattern from the ADC output stage cannot be sent to the demodulator (it can only be sent to the LVDS when the demodulator is off). RF mode without sync word can be set by the following: 1. Write 0x0041 to register 0xDF; that is MANUAL_DEC_FACTOR_EN = 1 and MANUAL_DEC_FACTOR = 1. 2. Write 0x121F to register 0xCA; that is MODULATE_BYPASS = 0 , FULL_LVDS_MODE = 1, DC_REMOVAL_BYPASS = 1, DWN_CNV_BYPASS = 1. DEC_BYPASS = 1, SYN_COS_RESET_ON_TX_TRIG = 0. 3. Write 0x6800 to register 0xC3; that is SERZ_FACTOR = 16x, OUTPUT_RESOLUTION = 16x, 4. Write 0x0010 to register 0xC4; that is MSB_FIRST = 1 5. Provide TX_TRIG pulse or set Reg 0xC0[2] MANUAL_TX_TRIG 54 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Filter Coefficent Test Mode Coefficient test mode allows for the streaming of coefficients through the demodulator to the LVDS. Filter coefficient test mode can be set by the following: 1. Enable TM_COEFF_EN. 2. Write OUTPUT_RESOLUTION (0x03[11:9]) = 0b100, that is 16-bit output (Note that output bit resolution of 14 bit will not give proper result). 3. Write DC_REMOVAL_BYPASS (0x0A[0]) = 1, DWN_CNV_BYPASS (0x0A[2]) = 1. 4. Write DC_DEC_SHIFT_FORCE_EN (0x1D[7]) = 1, DEC_SHIFT_FORCE (0x1D[6:4] = 0b110 and DEC_SHIFT_SCALE (0x0a[13]) = 1 5. Write MODULATE_BYPASS (0x0A[14]) = 1. After writing all of the above settings, coefficients come at the output in the sequence as below 6. M = 2 – Address 0: C15 C13 C11 C09 C07 C05 C03 C01; Address 1: C14 C12 C10 C08 C06 C04 C02 C00 – The order in which coefficients will come at the output will be: 0 C01 C03 C05 C07 C09 C11 C13 C15 C14 C12 C10 C08 C06 C04 C02 C00 C00 C02 C04 C06 C08 C10 C12 C14 C15 C13 C11 C09 C07 C05 C03 C01 0 7. M = 8 – The coefficients come to the output as shown in Figure 69. First sample 0 Coeff63 Coeff55 Coeff47 Coeff39 Coeff31 Coeff23 Coeff15 Coeff7 1 Coeff62 Coeff54 Coeff46 Coeff38 Coeff30 Coeff22 Coeff14 Coeff6 2 Coeff61 Coeff53 Coeff45 Coeff37 Coeff29 Coeff21 Coeff13 Coeff5 3 Coeff60 Coeff52 Coeff44 Coeff36 Coeff28 Coeff20 Coeff12 Coeff4 4 Coeff59 Coeff51 Coeff43 Coeff35 Coeff27 Coeff19 Coeff11 Coeff3 5 Coeff58 Coeff50 Coeff42 Coeff34 Coeff26 Coeff18 Coeff10 Coeff2 6 Coeff57 Coeff49 Coeff41 Coeff33 Coeff25 Coeff17 Coeff9 Coeff1 7 Coeff56 Coeff48 Coeff40 Coeff32 Coeff24 Coeff16 Coeff8 Coeff0 Last sample Note: once it reaches to last sample, it will start giving coefficients in the reverse direction till it reaches the point it started. Figure 69. Coefficient Readout Sequence Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 55 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com TX_SYNC and SYNC_WORD TIMING As shown in the below figure, hardware TX_SYNC is latched at the next negative edge of the ADC Clock after 0 to 1 transition of TX_SYNC. The time gap between latched edge and the start of the LVDS SYNC_WORD is kT ns where T is the time period of ADC Clock and k = 16 + decFactor + 1. tSETUP and tHOLD can be considered as 1.5 ns in the normal condition. Both will be at the negative edge of the ADC Clock. Figure 70. Sync Word Generation with Respect to TX_TRIG FIR Filter Delay vs. TX_TRIG Timing AFE5809’s decimation filter is a symmetric M×16 order FIR filter, where M is the decimation factor from 1 to 32. Half of the M×16 coefficients are stored in the filter coefficient memory. For a discrete-time FIR filter, its output is a weighted sum of the current and a finite number of previous values of the input as the below equation shows: Y [n] C0 u X[n] + C1u X[n - 1]... C N u X[n - N] (4) where X[n] is the input signal, Y[n] is the output signal, CN is the filter coefficients, and N is the filter order. Therefore the delay of AFE5809 output is related to decimation factor M. The TX_TRIG timing also plays a role in this. In the below description, we use M=1 and M=2 as examples to derive a generic timing relationship among TX_TRIG, AFE input and AFE output. The below register settings are used when the delay relationship was measured: • Enable demodulator (22[0] = 1, or 0x16[0] = 1) • Set different decimation factor and other settings in profile RAM. • Write filter coefficients in coefficient memory. • Set DEC_SHIFT_FORCE_EN (29[7] = 1 or 0x1D[7] = 1) • Set DEC_SHIFT_SCALE (10[13] = 1 or 0xA[13] = 1) • Set DEC_SHIFT_FORCE (29[6:4] = 6, or 0x1D[6:4] = 6) • Set RESERVED bits (10[15] = 0, 10[12] = 1, 10[4] = 1, 10[1] = 1; or 0xA[15] = 0, 0xA[12] = 1, 0xA[4] = 1, 0xA[1] = 1) • Set DC_REMOVAL_BYPASS (10[0] = 1 or 0xA[0] = 1) • SIN_COS_RESET_ON_TX_TRIG (10[10] = 1 or 0xA[10] = 1) • SERZ_FACTOR (03[14:13] = 11) (16X serialization) • OUTPUT_RESOLUTION (03[11:9] = 100) (16 bit) • MSB_FIRST (04[4] = 1) • SYNC_WORD (11[15:0] or 0xB[15:0] ) (Set sync word. It can be user dependent) 56 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com • • SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Down conversion is enabled and down convert frequency set to 0 that is multiply input signal with DC. Please note even this frequency is set to value other than 0, will not change the demod latency. For experiment ease mixing with DC is performed. Please note that, ADC sampling frequency and VCA LPF settings has been kept such that AFE5809’s demod sees a single pulse. When M = 1, 8 filter coefficients written in the memory are C0, C1 to C7. An impulse signal is applied at both VCA input and TX_TRIG. Due to the impulse input, coefficients starts coming at the output according to timing diagram shown in the following figure, where 20 cycle delay is observed. Sampling Cycle ADC CLOCK AFE INPUT TX_TRIG DATA N DATA N+1 DATA DATA N+2 N+3 DATA N+14 0000 0000 Sync Word C0 C1 C2 C3 20 Cycles Figure 71. Expected Latency Timing when M = 1 By adjusting the timing between AFE input and TX_TRIG, we can obtain a timing diagram similar as Figure 71. Sampling Cycle ADC CLOCK AFE INPUT TX_ TRIG DATA N DATA N+1 DATA DATA N+2 N+3 2 Cycles DATA N+14 0000 0000 Sync Word C0 C1 C2 C3 C4 C5 18 Cycles Figure 72. Measured Latency Timing when M = 1 By adjusting the timing between AFE input and TX_TRIG, we can obtain a timing diagram similar as Figure 72. When M = 2, if impulse is given one clock before TX_TRIG signal, then sample followed after SYNC WORD gives impulse response of the filter as shown in Figure 73. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 57 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Sampling Cycle ADC CLOCK AFE INPUT TX_ TRIG DATA N DATA N+1 DATA DATA N+2 N+3 DATA N+15 1 Cycles 0000 0000 0000 Sync Word C0 C2 C4 C8 C6 C10 19 Cycles Figure 73. Measured Latency Timing when M = 2 A generic timing diagram is shown below. Here number of zeros comes before sync word is equals to Z. Sync word comes after S number of cycles, impulse response starts coming after L number of cycles, and input impulse is given after IP cycles with respect to TX_TRIG signal. Therefore for different decimation factor (M), values of these numbers are listed down in Table 27 andFigure 74. Table 27. Generic Latency vs. Decimation factor M M Number of Zeros (ZNo) Sync Word Latency (S) Data Latency (L) Input Impulse (IP) 1 2 17 18 -2 2 3 18 19 -1 3 4 19 20 0 4 5 20 21 1 5 6 21 22 2 6 7 22 23 3 7 8 23 24 4 8 9 24 25 5 M M+1 16 + M 17 + M M–3 Notes • • • Negative number represents input is given in advance with respect to TX_TRIG signal. When DC_REMOVAL_BYPASS 10[0] = 0 or 0xA[0] = 0, the Sync word Latency and Data Latency becomes 17 + M and 18 + M ADC's low latency mode enabled by Reg. 0x2[12] doesn't impact S and L. Sampling Cycle ADC CLOCK AFE INPUT TX_TRIG IP Cycles 20 Cycles C(0+2*M) DATA DATA N+1 N DATA DATA N+2 N+3 DATA 0000 N+14 NOz Sync Word C0 C(0+M) C(0+3*M) S Cycles L Cycles Figure 74. Measured Latency Timing at any M 58 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Expression of Decimation Filter Response Based on the previous table, the decimation filter’s response is formulated. Figure 75 indicates that the Tx_Trig sample is considered as the reference for time scale. So the input to the device at Tx_Trig clock shall be expressed as X[0], the next sample input as X[1], and so on. Similarly, the output of device followed by the AFE5809’s demodulator shall be expressed as Y[0] at the instant of Tx_Trig, Y[1] at the next clock and so on; Cn or C(n) indicates the coefficient of nth index. ADC CLOCK INPUT X[-2] X[-1] X[0] X[1] X[2] Y[0] Y[1] Y[2] X[3] X[4] X[14] X[15] X[17+M] Y[14] Y[15]= 0000 Sync Y[17+M] Word TX_TRIG Y[3] Figure 75. Typical Timing Expression among ADC CLK, Input, TX_TRIG and Output For M = 1, the number of zeroes, ZNo = 2 ; Sync Word Latency S = 17. So the output values from sample 18 will be relevant and the first few samples are: Y [18] C0 u X[-2] + C1 u X[-3] + C2 u X[-4] + «+ C7 u X[-9] + C7 u X[-10] + «+ C[0] u X[-17] Y [19] C0 u X[-1] + C1 u X[-2] + C2 u X[-3] + «+ C7 u X[-8] + C7 u X[-9] + «+ C[0] u X[-16] Y [20] C0 u X[0] + C1 u X[-1] + C2 u X[-2] + «+ C7 u X[-7] + C7 u X[-8] + «+ C[0] u X[-15] ... (5) All these samples appear at the output since no samples are dropped for decimation factor = 1. For M = 2, the number of zeroes, ZNo = 3 ; Sync Word Latency S = 18. So the output values from sample 19 will be relevant and the first few samples are described here: Y [18] C0 u X[-2] + C1 u X[-3] + C2 u X[-4] + «+ C7 u X[-9] + C7 u X[-10] + «+ C[0] u X[-17] Y [19] C0 u X[-1] + C1 u X[-2] + C2 u X[-3] + «+ C7 u X[-8] + C7 u X[-9] + «+ C[0] u X[-16] Y [20] C0 u X[0] + C1 u X[-1] + C2 u X[-2] + «+ C7 u X[-7] + C7 u X[-8] + «+ C[0] u X[-15] ... (6) But for M = 2, every alternate sample has to be dropped. The decimation is adjusted in such a way that the first sample after sync is retained. Hence in this case Y[19], Y[21], Y[23], and so forth are retained and Y[20], Y[22], Y[24] are dropped. For M = 3, the number of zeroes, ZNo = 4 ; Sync Word Latency S = 19. So the output values from sample 20 will be relevant and the first few samples are described here: Y [18] C0 u X[-2] + C1 u X[-3] + C2 u X[-4] + «+ C7 u X[-9] + C7 u X[-10] + «+ C[0] u X[-17] Y [19] C0 u X[-1] + C1 u X[-2] + C2 u X[-3] + «+ C7 u X[-8] + C7 u X[-9] + «+ C[0] u X[-16] Y [20] C0 u X[0] + C1 u X[-1] + C2 u X[-2] + «+ C7 u X[-7] + C7 u X[-8] + «+ C[0] u X[-15] ... (7) But for M = 3, every two among three samples have to be dropped. The decimation is adjusted in such a way that the first sample after sync is retained. Hence in this case Y[20], Y[23], Y[26], and so forth are retained and Y[21], Y[22], Y[24], Y[25], and so forth are dropped. For any M,This pattern can be generalized for a decimation factor of M. The number of ZNo = M + 1, Sync Word Latency S = 16 + M. So the output values from sample (17 + M) will be relevant and the first few samples are described here: Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 59 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Y [18] C0 u X[-2] + C1 u X[-3] + C2 u X[-4] + «+ C7 u X[-9] + C7 u X[-10] + «+ C[0] u X[-17] Y [19] C0 u X[-1] + C1 u X[-2] + C2 u X[-3] + «+ C7 u X[-8] + C7 u X[-9] + «+ C[0] u X[-16] Y [20] C0 u X[0] + C1 u X[-1] + C2 u X[-2] + «+ C7 u X[-7] + C7 u X[-8] + «+ C[0] u X[-15] ... (8) For a decimation factor of M which is not 1, the decimation is adjusted in such a way that the first sample after sync is retained. Hence in this case Y[17+M], Y[17+2M], Y[17+3M], and so forth are retained and the rest of samples between these that is Y[18+M], Y[19+2M],…, Y[16+2M] are dropped. 60 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 THEORY OF OPERATION AFE5809 OVERVIEW The AFE5809 is a highly integrated analog front-end (AFE) solution specifically designed for ultrasound systems in which high performance and small size are required. The AFE5809 integrates a complete time-gain-control (TGC) imaging path and a continuous wave Doppler (CWD) path. It also enables users to select one of various power/noise combinations to optimize system performance. The AFE5809 contains eight channels; each channels includes a low-noise amplifier (LNA), voltage controlled attenuator (VCAT), programmable gain amplifier (PGA), low-pass filter (LPF), 14-bit analog-to-digital converter (ADC), digital I/Q demodulator, and CW mixer. Multiple features in the AFE5809 are suitable for ultrasound applications, such as active termination, individual channel control, fast power-up and power-down response, programmable clamp voltage control, fast and consistent overload recovery, and so on. Therefore, the AFE5809 brings premium image quality to ultraportable, handheld systems all the way up to high-end ultrasound systems. In addition, the signal chain of the AFE5809 can handle signal frequency as low as 50 kHz and as high as 30 MHz. This enables the AFE5809 to be used in both sonar and medical applications. The simplified function block diagram is shown in Figure 76. SPI IN 16X CLKP 16X CLKN AFE5809 with Demodulator 1 of 8 Channels SPI Logic VCAT LNA 0 to -40 dB 16 Phases Generator 1X CLK CW Mixer PGA 24, 30dB 3rd LP Filter 10, 15, 20, 30 MHz 14 Bit ADC Digital DeMod & LP Filter Summing Amplifier/ Filter Reference Reference Logic Control CW I/Q Vout Differential TGC Vcntl EXT/INT REFM/P DeMod Control LVDS LVDS Serializer OUT Figure 76. Functional Block Diagram LOW-NOISE AMPLIFIER (LNA) In many high-gain systems, a low noise amplifier is critical to achieve overall performance. Using a new proprietary architecture, the LNA in the AFE5809 delivers exceptional low-noise performance, while operating on a low quiescent current compared to CMOS-based architectures with similar noise performance. The LNA performs single-ended input to differential output voltage conversion. It is configurable for a programmable gain of 24, 18. 12 dB and its input-referred noise is only 0.63, 0.70, 0.9 nV/√Hz respectively. Programmable gain settings result in a flexible linear input range up to 1 Vpp, realizing high signal handling capability demanded by new transducer technologies. Larger input signal can be accepted by the LNA; however the signal can be distorted since it exceeds the LNA’s linear operation region. Combining the low noise and high input range, a wide input dynamic range is achieved consequently for supporting the high demands from various ultrasound imaging modes. The LNA input is internally biased at approximately +2.4 V; the signal source should be AC-coupled to the LNA input by an adequately-sized capacitor, for example ≥ 0.1 µF. To achieve low DC offset drift, the AFE5809 incorporates a DC offset correction circuit for each amplifier stage. To improve the overload recovery, an integrator circuit is used to extract the DC component of the LNA output and then fed back to the LNA’s complementary input for DC offset correction. This DC offset correction circuit has a high-pass response and can be treated as a high-pass filter. The effective corner frequency is determined by the capacitor CBYPASS connected at INM. With larger capacitors, the corner frequency is lower. For stable operation at the highest HP filer cut-off Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 61 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com frequency, a ≥ 15-nF capacitor can be selected. This corner frequency scales almost linearly with the value of the CBYPASS. For example, 15 nF gives a corner frequency of approximately 100 kHz, while 47 nF can give an effective corner frequency of 33 kHz. The DC offset correction circuit can also be disabled/enabled through register 52[12]. A large capacitor like 1 µF can be used for setting low corner frequency (<2 KHz) of the LNA DC offset correction circuit. Figure 59 shows the frequency responses for low frequency applications. The AFE5809 can be terminated passively or actively. Active termination is preferred in ultrasound application for reducing reflection from mismatches and achieving better axial resolution without degrading noise figure too much. Active termination values can be preset to 50, 100, 200, and 400 Ω; other values also can be programmed by users through register 52[4:0]. A feedback capacitor is required between ACTx and the signal source as Figure 77 shows. On the active termination path, a clamping circuit is also used to create a low impedance path when overload signal is seen by the AFE5809. The clamp circuit limits large input signals at the LNA inputs and improves the overload recovery performance of the AFE5809. The clamp level can be set to 350 mVpp, 600 mVpp, 1.15 Vpp automatically depending on the LNA gain settings when register 52[10:9] = 0. Other clamp voltages, such as 1.15 Vpp, 0.6 Vpp, and 1.5 Vpp, are also achievable by setting register 52[10:9]. This clamping circuit is also designed to obtain good pulse inversion performance and reduce the impact from asymmetric inputs. CLAMP AFE CACT ACTx INPx CIN INPUT CBYPSS INMx LNAx DC Offset Correction Figure 77. AFE5809 LNA With DC Offset Correction Circuit VOLTAGE-CONTROLLED ATTENUATOR The voltage-controlled attenuator is designed to have a linear-in-dB attenuation characteristic; that is, the average gain loss in dB (refer to Figure 2) is constant for each equal increment of the control voltage (VCNTL) as shown in Figure 78. A differential control structure is used to reduce common mode noise. A simplified attenuator structure is shown in the following Figure 78 and Figure 79. The attenuator is essentially a variable voltage divider that consists of the series input resistor (RS) and seven shunt FETs placed in parallel and controlled by sequentially activated clipping amplifiers (A1 through A7). VCNTL is the effective difference between VCNTLP and VCNTLM. Each clipping amplifier can be understood as a specialized voltage comparator with a soft transfer characteristic and well-controlled output limit voltage. Reference voltages V1 through V7 are equally spaced over the 0V to 1.5Vcontrol voltage range. As the control voltage increases through the input range of each clipping amplifier, the amplifier output rises from a voltage where the FET is nearly OFF to VHIGH where the FET is completely ON. As each FET approaches its ON state and the control voltage continues to rise, the next clipping amplifier/FET combination takes over for the next portion of the piecewise-linear attenuation characteristic. Thus, low control voltages have most of the FETs turned OFF, producing minimum signal attenuation. Similarly, high control voltages turn the FETs ON, leading to maximum signal attenuation. Therefore, each FET acts to decrease the shunt resistance of the voltage divider formed by Rs and the parallel FET network. 62 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Additionally, a digitally controlled TGC mode is implemented to achieve better phase-noise performance in the AFE5809. The attenuator can be controlled digitally instead of the analog control voltage VCNTL. This mode can be set by the register bit 59[7]. The variable voltage divider is implemented as a fixed series resistance and FET as the shunt resistance. Each FET can be turned ON by connecting the switches SW1-7. Turning on each of the switches can give approximately 6 dB of attenuation. This can be controlled by the register bits 59[6:4]. This digital control feature can eliminate the noise from the VCNTL circuit and ensure the better SNR and phase noise for the TGC path. A1 - A7 Attenuator Stages Attenuator Input RS Attenuator Output Q1 VB A1 Q2 A1 Q3 A1 C1 C2 V1 Q4 A1 C3 V2 Q5 A1 C4 V3 Q6 A1 C5 V4 Q7 A1 C6 V5 C7 V6 V7 VCNTL C1 - C8 Clipping Amplifiers Control Input Figure 78. Simplified Voltage Controlled Attenuator (Analog Structure) Attenuator Input RS Attenuator Output Q1 Q2 Q3 Q4 Q5 SW5 SW6 Q6 Q7 VB SW1 SW2 SW3 SW4 SW7 VHIGH Figure 79. Simplified Voltage Controlled Attenuator (Digital Structure) The voltage controlled attenuator’s noise follows a monotonic relationship to the attenuation coefficient. At higher attenuation, the input-referred noise is higher and vice-versa. The attenuator’s noise is then amplified by the PGA and becomes the noise floor at ADC input. In the attenuator’s high attenuation operating range, that is VCNTL is high, the attenuator’s input noise may exceed the LNA output noise; the attenuator then becomes the dominant noise source for the following PGA stage and ADC. Therefore, the attenuator noise should be minimized compared to the LNA output noise. The AFE5809 attenuator is designed for achieving very low noise even at high attenuation (low channel gain) and realizing better SNR in near field. The input referred noise for different attenuations is listed in Table 28: Table 28. Voltage-Controlled-Attenuator Noise vs Attenuation Attenuation (dB) Attenuator Input Referred noise (nV/rtHz) –40 10.5 –36 10 –30 9 –24 8.5 –18 6 –12 4 –6 3 0 2 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 63 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com PROGRAMMABLE GAIN AMPLIFIER (PGA) After the voltage controlled attenuator, a programmable gain amplifier can be configured as 24dB or 30dB with a constant input referred noise of 1.75 nV/rtHz. The PGA structure consists of a differential voltage-to-current converter with programmable gain, clamping circuits, a transimpedance amplifier with a programmable low-pass filter, and a DC offset correction circuit. Its simplified block diagram is shown in Figure 80. CLAMP From attenuator To ADC I/V LPF V/I CLAMP DC Offset Correction Loop Figure 80. Simplified Block Diagram of PGA Low input noise is always preferred in a PGA and its noise contribution should not degrade the ADC SNR too much after the attenuator. At the minimum attenuation (used for small input signals), the LNA noise dominates; at the maximum attenuation (large input signals), the PGA and ADC noise dominates. Thus 24 dB gain of PGA achieves better SNR as long as the amplified signals can exceed the noise floor of the ADC. The PGA clamping circuit can be enabled (register 51) to improve the overload recovery performance of the AFE. If we measure the standard deviation of the output just after overload, for 0.5 V VCNTL, it is about 3.2 LSBs in normal case, that is the output is stable in about 1 clock cycle after overload. With the clamp disabled, the value approaches 4 LSBs meaning a longer time duration before the output stabilizes; however, with the clamp enabled, there will be degradation in HD3 for PGA output levels > –2 dBFS. For example, for a –2-dBFS output level, the HD3 degrades by approximately 3 dB. In order to maximize the output dynamic range, the maximum PGA output level can be above 2 Vpp even with the clamp circuit enabled; the ADC in the AFE5809 has excellent overload recovery performance to detect small signals right after the overload. NOTE In the low power and medium power modes, PGA_CLAMP is disabled for saving power if 51[7] = 0. The AFE5809 integrates an anti-aliasing filter in the form of a programmable low-pass filter (LPF) in the transimpedance amplifier. The LPF is designed as a differential, active, 3rd order filter with Butterworth characteristics and a typical 18dB per octave roll-off. Programmable through the serial interface, the –1-dB frequency corner can be set to one of 10, 15, 20, and 30 MHz. The filter bandwidth is set for all channels simultaneously. A selectable DC offset correction circuit is implemented in the PGA as well. This correction circuit is similar to the one used in the LNA. It extracts the DC component of the PGA outputs and feeds back to the PGA complimentary inputs for DC offset correction. This DC offset correction circuit also has a high-pass response with a cut-off frequency of 80 KHz. ANALOG TO DIGITAL CONVERTER The analog-to-digital converter (ADC) of the AFE5809 employs a pipelined converter architecture that consists of a combination of multi-bit and single-bit internal stages. Each stage feeds its data into the digital error correction logic, ensuring excellent differential linearity and no missing codes at the 14-bit level. The 14 bits given out by each channel are serialized and sent out on a single pair of pins in LVDS format. All eight channels of the AFE5809 operate from a common input clock (CLKP/M). The sampling clocks for each of the eight channels are generated from the input clock using a carefully matched clock buffer tree. The 14x clock required for the 64 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 serializer is generated internally from the CLKP/M pins. A 7x and a 1x clock are also given out in LVDS format, along with the data, to enable easy data capture. The AFE5809 operates from internally-generated reference voltages that are trimmed to improve the gain matching across devices. The nominal values of REFP and REFM are 1.5 V and 0.5 V, respectively. Alternately, the device also supports an external reference mode that can be enabled using the serial interface. Using serialized LVDS transmission has multiple advantages, such as a reduced number of output pins (saving routing space on the board), reduced power consumption, and reduced effects of digital noise coupling to the analog circuit inside the AFE5809. CONTINUOUS-WAVE (CW) BEAMFORMER Continuous-wave Doppler is a key function in mid-end to high-end ultrasound systems. Compared to the TGC mode, the CW path needs to handle high dynamic range along with strict phase noise performance. CW beamforming is often implemented in analog domain due to the mentioned strict requirements. Multiple beamforming methods are being implemented in ultrasound systems, including passive delay line, active mixer, and passive mixer. Among all of them, the passive mixer approach achieves optimized power and noise. It satisfies the CW processing requirements, such as wide dynamic range, low phase noise, accurate gain and phase matching. A simplified CW path block diagram and an In-phase or Quadrature (I/Q) channel block diagram are illustrated below respectively. Each CW channel includes a LNA, a voltage-to-current converter, a switch-based mixer, a shared summing amplifier with a low-pass filter, and clocking circuits. NOTE The local oscillator inputs of the passive mixer are cos(ωt) for I-CH and sin(ωt) for Q-CH respectively. Depending on users' CW Doppler complex FFT processing, swapping I/Q channels in FPGA or DSP may be needed in order to get correct blood flow directions. All blocks include well-matched in-phase and quadrature channels to achieve good image frequency rejection as well as beamforming accuracy. As a result, the image rejection ratio from an I/Q channel is better than –46 dBc which is desired in ultrasound systems. I-CLK LNA1 Voltage to Current Converter I-CH Q-CH Q-CLK Sum Amp with LPF 1×fcw CLK I-CH Clock Distribution Circuits Q-CH N×fcw CLK Sum Amp with LPF I-CLK LNA8 Voltage to Current Converter I-CH Q-CH Q-CLK Figure 81. Simplified Block Diagram of CW Path Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 65 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com ACT1 500Ω IN1 INPUT1 INM1 Mixer Clock 1 LNA1 Cext 500Ω ACT2 500Ω IN2 INPUT2 INM2 Mixer Clock 2 CW_AMPINM LNA2 500Ω Rint/Rext CW_OUTP I/V Sum Amp 10Ω 10Ω CW _AMPINP Rint/Rext CW_OUTM Cext CW I or Q CHANNEL Structure ACT8 500Ω IN8 INPUT8 INM8 Mixer Clock 8 LNA8 500Ω Note: the approximately 10- to 15-Ω resistors at CW_AMPINM/P are due to internal IC routing and can create slight attenuation. Figure 82. A Complete In-phase or Quadrature Phase Channel The CW mixer in the AFE5809 is passive and switch based; passive mixer adds less noise than active mixers. It achieves good performance at low power. Figure 83 and the equations describe the principles of mixer operation, where Vi(t), Vo(t), and LO(t) are input, output, and local oscillator (LO) signals for a mixer respectively. The LO(t) is square-wave based and includes odd harmonic components, as shown in Equation 9: Vi(t) Vo(t) LO(t) Figure 83. Block Diagram of Mixer Operation Vi(t) = sin (w0 t + wd t + j ) + f (w0 t ) 4é 1 1 ù sin (w0 t ) + sin (3w0 t ) + sin (5w0 t )...ú ê 3 5 pë û 2 Vo(t) = éëcos (wd t + f ) - cos (2w0 t - wd t + f )...ùû p LO(t) = 66 Submit Documentation Feedback (9) Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 From the previous equations, the 3rd and 5th order harmonics from the LO can interface with the 3rd and 5th order harmonic signals in the Vi(t); or the noise around the 3rd and 5th order harmonics in the Vi(t). Therefore. the mixer’s performance is degraded. In order to eliminate this side effect due to the square-wave demodulation, a proprietary harmonic suppression circuit is implemented in the AFE5809. The 3rd and 5th harmonic components from the LO can be suppressed by over 12 dB. Thus the LNA output noise around the 3rd and 5th order harmonic bands will not be down-converted to base band. Hence, better noise figure is achieved. The conversion loss of the mixer is about –4 dB which is derived from 20log10 2 p The mixed current outputs of the 8 channels are summed together internally. An internal low noise operational amplifier is used to convert the summed current to a voltage output. The internal summing amplifier is designed to accomplish low power consumption, low noise, and ease of use. CW outputs from multiple AFE5809s can be further combined on system board to implement a CW beamformer with more than 8 channels. More detail information can be found in the application information section. Multiple clock options are supported in the AFE5809 CW path. Two CW clock inputs are required: N × ƒcw clock and 1 × ƒcw clock, where ƒcw is the CW transmitting frequency and N could be 16, 8, 4, or 1. Users have the flexibility to select the most convenient system clock solution for the AFE5809. In the 16 × ƒcw and 8 × ƒcw modes, the 3rd and 5th harmonic suppression feature can be supported. Thus the 16 × ƒcw and 8 × ƒcw modes achieves better performance than the 4 × ƒcw and 1 × ƒcw modes 16 × ƒcw Mode The 16 × ƒcw mode achieves the best phase accuracy compared to other modes. It is the default mode for CW operation. In this mode, 16 × ƒcw and 1 × ƒcw clocks are required. 16×fcw generates LO signals with 16 accurate phases. Multiple AFE5809s can be synchronized by the 1 × ƒcw , that is LO signals in multiple AFEs can have the same starting phase. The phase noise spec is critical only for 16X clock. 1X clock is for synchronization only and doesn’t require low phase noise. Please see the phase noise requirement in the section of application information. The top level clock distribution diagram is shown in the below Figure 84. Each mixer's clock is distributed through a 16 × 8 cross-point switch. The inputs of the cross-point switch are 16 different phases of the 1x clock. TI recommends to align the rising edges of the 1 × ƒcw and 16 × ƒcw clocks. The cross-point switch distributes the clocks with appropriate phase delay to each mixer. For example, Vi(t) is a 1 received signal with a delay of 16 T , a delayed LO(t) should be applied to the mixer in order to compensate for 1 2p T 16 16 the delay. Thus a 22.5⁰ delayed clock, that is , is selected for this channel. The mathematic calculation is expressed in the following equations: é æ ù 1 ö Vi(t) = sin êw0 ç t + ÷ + wd t ú = sin [w0 t + 22.5° + wd t ] ëê è 16 f0 ø ûú LO(t) = é æ 4 1 öù 4 sin êw0 ç t + ÷ ú = sin [w0 t + 22.5°] p êë è 16 f0 ø úû p Vo(t) = 2 cos (wd t ) + f (wn t ) p (10) Vo(t) represents the demodulated Doppler signal of each channel. When the Doppler signals from N channels are summed, the signal to noise ratio improves. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 67 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Fin 16X Clock www.ti.com INV D Q Fin 1X Clock Fin 1X Clock 16 Phase Generator 1X Clock Phase 0º 1X Clock Phase 22.5º SPI 1X Clock Phase 292.5º 1X Clock Phase 315º 1X Clock Phase 337.5º 16-to-8 Cross Point Switch Mixer 1 1X Clock Mixer 2 1X Clock Mixer 3 1X Clock Mixer 6 1X Clock Mixer 7 1X Clock Mixer 8 1X Clock Figure 84. Figure 85. 1x and 16x CW Clock Timing 8 × ƒcw and 4 × ƒcw Modes 8 × ƒcw and 4 × ƒcw modes are alternative modes when higher frequency clock solution (that is 16 × ƒcw clock) is not available in system. The block diagram of these two modes is shown below. 68 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Good phase accuracy and matching are also maintained. Quadature clock generator is used to create in-phase and quadrature clocks with exact 90° phase difference. The only difference between 8 × ƒcw and 4 × ƒcw modes is the accessibility of the 3rd and 5th harmonic suppression filter. In the 8 × ƒcw mode, the suppression filter can 1 be supported. In both modes, 16 T phase delay resolution is achieved by weighting the in-phase and quadrature 1 T 16 paths correspondingly. For example, if a delay of or 22.5° is targeted, the weighting coefficients should follow the below equations, assuming Iin and Qin are sin(ω0t) and cos(ω0t) respectively: æ 1 ö æ 2p ö æ 2p ö Idelayed (t) = Iin cos ç ÷ + Qin sin ç ÷ = Iin ç t + ÷ è 16 ø è 16 ø è 16 f0 ø æ 1 ö æ 2p ö æ 2p ö Qdelayed (t) = Qin cos ç ÷ - Iin sin ç ÷ = Qin ç t + ÷ è 16 ø è 16 ø è 16 f0 ø (11) Therefore, after I/Q mixers, phase delay in the received signals is compensated. The mixers’ outputs from all channels are aligned and added linearly to improve the signal to noise ratio. It is preferred to have the 4 × ƒcw or 8 × ƒcw and 1 × ƒcw clocks aligned both at the rising edge. INV 4X/8X Clock I/Q CLK Generator D Q 1X Clock LNA2~8 In-phase CLK Summed In-Phase Quadrature CLK I/V Weight Weight LNA1 I/V Weight Summed Quadrature Weight Figure 86. 8 × ƒcw and 4 × ƒcw Block Diagram Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 69 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Figure 87. 8 × ƒcw and 4 × ƒcw Timing Diagram 1 × ƒcw Mode 1 T 16 The 1 × ƒcw mode requires in-phase and quadrature clocks with low phase noise specifications. The phase delay resolution is also achieved by weighting the in-phase and quadrature signals as described in the 8 × ƒcw and 4 × ƒcw modes. Syncronized I/Q CLOCKs LNA2~8 In-phase CLK Summed In-Phase Quadrature CLK I/V Weight Weight LNA1 I/V Weight Summed Quadrature Weight Figure 88. Block Diagram of 1 x ƒcw mode 70 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 DIGITAL I/Q DEMODULATOR AFE5809 also includes a digital in-phase and quadrature (I/Q) demodulator and a low-pass decimation filter. The main purpose of the demodulation block is to reduce the LVDS data rate and improve overall system power efficiency. The I/Q demodulator accepts ADC output with up to 65MSPS sampling rate and 14-bit resolution. For example, after digital demodulation and 4× decimation filtering, the data rate for either in-phase or quadrature output is reduced to 16.25 MSPS, and the data resolution is improved to 16 bit consequently. Hence, the overall LVDS trace reduction can be a factor of 2. This demodulator can be bypassed and powered down completely if it is not needed. The digital demodulator block given in AFE5809 is designed to do down-conversion followed by decimation. The top level block is divided into two exactly similar blocks: (1) Subchip0 (2) Subchip1. Both subchips share 4 channels each that is subchip0 (ADC.1, ADC.2, ADC.3 and ADC.4) and subchip1 (ADC.5, ADC.6, ADC.7 and ADC.8). ADC.1 ADC.2 ADC.3 ADC.4 ADC.5 ADC.6 ADC.7 ADC.8 LVDS.1 CH.A LVDS.2 CH.B CH.C Sub-Chip 0 LVDS.3 LVDS.4 CH.D LVDS.5 CH.A LVDS.6 CH.B Sub-Chip 1 CH.C CH.D LVDS.7 LVDS.8 Figure 89. Subchip The following 4 functioning blocks are given in each demodulator. Every block can be bypassed. 1. DC Removal Block 2. Down Conversion 3. Decimator 4. Channel Multiplexing Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 71 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com Down Conversion (I Phase) Decimator M A.I To Channel Multiplexing Cos ωt DC Removal Block Down Sampler Decimation Filter DC Offset Channel A Down Conversion (Q Phase) Decimator -Sin ωt M A.Q To Channel Multiplexing Down Sampler Decimation Filter Figure 90. Digital Demodulator Block 1. DC Removal Block is used to remove DC offset. An offset value can be given to specific register. 2. Down Conversion or Demodulation of signal is done by multiplying signal by cos(ω0t) and by -sin(ω0t) to give out I phase and Q phase respectively. cos(ωt) and -sin(ωt) are 14-bit wide plus a sign bit. ω = 2πf, f can be set with resolution Fs / 216, where Fs is the ADC sampling frequency. NOTE The digital demodulator is based on a conventional down converter, that is, -sin(ω0t) is used for Q phase. 3. Decimator Block has two functions, Decimation Filter and Down Sampler. Decimation Filter is a variable coefficient symmetric FIR filter and it's coefficients can be given using Coefficient RAM. Number of taps of FIR filter is 16 x decimation factor (M). For decimation factor of M, 8M coefficients have to be stored in Coefficient Bank. Each coefficient is 14-bit wide. Down-sampler gives out 1 sample followed by M – 1 samples zeros. 4. In Figure 91, channel multiplexing is implemented for flexible data routing: 72 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 ADC.1 A.I ADC.1 Channel A 14bits 16bits Single Channel Demodulator Blocks A.Q 16bits LVDS.1 C H Serializer DEMOD.1 A N N ADC.2 E B.I ADC.2 Channel B 14bits LVDS.2 L 16bits Single Channel Demodulator Blocks Serializer DEMOD.2 B.Q 16bits M U ADC.3 L C.I ADC.3 Channel C 14bits 16bits Single Channel Demodulator Blocks C.Q 16bits LVDS.3 Serializer T I DEMOD.3 P L E ADC.4 X D.I ADC.4 Channel D 14bits 16bits Single Channel Demodulator Blocks I N LVDS.4 Serializer DEMOD.4 G D.Q 16bits Figure 91. Channel Multiplexing EQUIVALENT CIRCUITS CM CM (a) INP (b) INM (c) ACT S0492-01 Figure 92. Equivalent Circuits of LNA inputs Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 73 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com S0493-01 Figure 93. Equivalent Circuits of VCNTLP/M VCM 5 kΩ 5 kΩ CLKP CLKM (a) CW 1X and 16X Clocks (b) ADC Input Clocks S0494-01 Figure 94. Equivalent Circuits of Clock Inputs 74 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 (a) CW_OUTP/M (b) CW_AMPINP/M S0495-01 Figure 95. Equivalent Circuits of CW Summing Amplifier Inputs and Outputs + – Low +Vdiff High AFE5809 OUTP + – –Vdiff + – High Vcommon Low External 100-W Load Rout OUTM Switch impedance is nominally 50 W (±10%) Figure 96. Equivalent Circuits of LVDS Outputs Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 75 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com APPLICATION INFORMATION SPI_DIG_EN TX_SYNC_IN Logic ‘1’: 1.8V IN CH1 IN CH4 IN CH5 IN CH6 IN CH7 IN CH8 1.4V 0.1μF DVDD AVDD 0.1μF DVDD_LDO2 D1M 15nF IN1M D2P 0.1μF ACT2 D2M 0.1μF 0.1μF IN2P D3P 15nF IN2M D3M 1μF ACT3 D4P 15nF IN3M D5P 1μF ACT4 D5M 0.1μF IN4P D6P 15nF IN4M D6M 1μF ACT5 0.1μF IN5P 15nF IN5M 1μF ACT6 0.1μF IN6P 15nF IN6M 1μF ACT7 Digital I/Q Demod CLKP CLKM 0.1μF CLKP_16X 0.1μF CLKM_16X 0.1μF CLKP_1X 0.1μF CLKM_1X AFE5809 CLOCK INPUTS SOUT SDATA SCLK D7P SEN AFE5809 D7M AFE5809 RESET D8P PDN_VCA D8M ANALOG INPUTS ANALOG OUTPUTS REF/BIAS DECOUPLING LVDS OUTPUTS PDN_GLOBAL DCLKM FCLKP OTHER AFE5809 OUTPUT FCLKM IN7P 15nF IN7M CW_IP_AMPINP REXT (optional) 1μF ACT8 CW_IP_OUTM CCW 0.1μF IN8P CW_IP_AMPINM REXT (optional) CW_IP_OUTP CCW IN8M OTHER AFE5809 OUTPUT CVCNTL 470pF VCNTLP VCNTLM CVCNTL 470pF VREF_IN DIGITAL INPUTS PDN_ADC DCLKP 0.1μF VHIGH AFE5809 Clock termination depends on clock types LVDS, PECL, or CMOS D4M IN3P >1μF RVCNTL 200Ω DVDD_LDO1 IN1P CM_BYP VCNTLM IN N*0.1μF DVSS 0.1μF 0.1μF >1μF VCNTLP IN N*0.1μF AVSS LDO_EN LDO_SETV D1P 15nF RVCNTL 200Ω N*0.1μF AVSS 10μF Logic ‘1’: 1.8V 1.8VD ACT1 0.1μF IN CH3 10μF 1.8VA 1μF 1μF IN CH2 10μF 3.3VA AVDD_ADC 0.1μF AVSS AVDD_5V 10μF 5VA OTHER AFE5809 OUTPUT CW_QP_AMPINP CW_QP_OUTM CAC RSUM CAC R SUM TO SUMMING AMP CAC RSUM CAC R SUM CCW CW_QP_AMPINM REXT (optional) CW_QP_OUTP CCW REFM CAC R SUM CAC RSUM CAC R SUM REXT (optional) TO SUMMING AMP DNCs REFP AVSS DVSS OTHER AFE5809 OUTPUT CAC RSUM Figure 97. Application Circuit With Digital Demodulator 76 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 A typical application circuit diagram is listed in Figure 97. The configuration for each block is discussed below. LNA CONFIGURATION LNA Input Coupling and Decoupling The LNA closed-loop architecture is internally compensated for maximum stability without the need of external compensation components. The LNA inputs are biased at 2.4 V and AC coupling is required. A typical input configuration is shown in Figure 98. CIN is the input AC coupling capacitor. CACT is a part of the active termination feedback path. Even if the active termination is not used, the CACT is required for the clamp functionality. Recommended values for CACT is ≥ 1 µF and CIN is ≥ 0.1 µF. A pair of clamping diodes is commonly placed between the T/R switch and the LNA input. Schottky diodes with suitable forward drop voltage (for example: the BAT754/54 series, the BAS40 series, the MMBD7000 series, or similar) can be considered depending on the transducer echo amplitude. AFE CLAMP CACT ACTx CIN INPx CBYPASS INMx Input LNAx Optional Diodes DC Offset Correction S0498-01 Figure 98. LNA Input Configurations This architecture minimizes any loading of the signal source that may lead to a frequency-dependent voltage divider. The closed-loop design yields low offsets and offset drift. CBYPASS (≥ 0.015 µF) is used to set the highpass filter cut-off frequency and decouple the complimentary input. Its cut-off frequency is inversely proportional to the CBYPASS value, The HPF cut-off frequency can be adjusted through the register 59[3:2] a Table 29 lists. Low frequency signals at T/R switch output, such as signals with slow ringing, can be filtered out. In addition, the HPF can minimize system noise from DC-DC converters, pulse repetition frequency (PRF) trigger, and frame clock. Most ultrasound systems’ signal processing unit includes digital high-pass filters or band-pass filters (BPFs) in FPGAs or ASICs. Further noise suppression can be achieved in these blocks. In addition, a digital HPF is available in the AFE5809 ADC. If low frequency signal detection is desired in some applications, the LNA HPF can be disabled. Table 29. LNA HPF Settings (CBYPASS = 15 nF) Reg59[3:2] (0x3B[3:2]) Frequency 00 100 kHz 01 50 kHz 10 200 kHz 11 150 kHz Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 77 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com CM_BYP and VHIGH pins, which generate internal reference voltages, need to be decoupled with ≥ 1-µF capacitors. Bigger bypassing capacitors (> 2.2 µF) may be beneficial if low frequency noise exists in system. LNA Noise Contribution The noise spec is critical for LNA and it determines the dynamic range of entire system. The LNA of the AFE5809 achieves low power and an exceptionally low-noise voltage of 0.63 nV/√Hz, and a low current noise of 2.7 pA/√Hz. Typical ultrasonic transducer’s impedance Rs varies from tens of ohms to several hundreds of ohms. Voltage noise is the dominant noise in most cases; however, the LNA current noise flowing through the source impedance (Rs) generates additional voltage noise. 2 2 LNA _ Noise total = VLNAnoise + R2s ´ ILNAnoise (12) The AFE5809 achieves low noise figure (NF) over a wide range of source resistances as shown in Figure 32, Figure 33, and Figure 34. Active Termination In ultrasound applications, signal reflection exists due to long cables between transducer and system. The reflection results in extra ringing added to echo signals in PW mode. Since the axial resolution depends on echo signal length, such ringing effect can degrade the axial resolution. Hence, either passive termination or active termination, is preferred if good axial resolution is desired. Figure 99 shows three termination configurations: Rs LNA (a) No Termination Rf Rs LNA (b) Active Termination Rs Rt LNA (c) Passive Termination S0499-01 Figure 99. Termination Configurations 78 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 Under the no termination configuration, the input impedance of the AFE5809 is about 6 kΩ (8 K//20pF) at 1 MHz. Passive termination requires external termination resistor Rt, which contributes to additional thermal noise. The LNA supports active termination with programmable values, as shown in Figure 100 . 450Ω 900Ω 1800Ω ACTx 3600Ω 4500Ω INPx Input INMx LNAx AFE S0500-01 Figure 100. Active Termination Implementation The AFE5809 has four pre-settings 50, 100, 200, and 400 Ω which are configurable through the registers. Other termination values can be realized by setting the termination switches shown in Figure 100. Register [52] is used to enable these switches. The input impedance of the LNA under the active termination configuration approximately follows: ZIN = Rf AnLNA 1+ 2 (13) Table 8 lists the LNA RINs under different LNA gains. System designers can achieve fine tuning for different probes. The equivalent input impedance is given by Equation 14 where RIN (8K) and CIN (20 pF) are the input resistance and capacitance of the LNA. ZIN = Rf / /CIN / /RIN AnLNA 1+ 2 (14) Therefore, the ZIN is frequency dependent and it decreases as frequency increases shown in Figure 10. Since 2 to 10 MHz is the most commonly used frequency range in medical ultrasound, this rolling-off effect doesn’t impact system performance greatly. Active termination can be applied to both CW and TGC modes. Since each ultrasound system includes multiple transducers with different impedances, the flexibility of impedance configuration is a great plus. Figure 32, Figure 33, and Figure 34 shows the NF under different termination configurations. It indicates that no termination achieves the best noise figure; active termination adds less noise than passive termination. Thus termination topology should be carefully selected based on each use scenario in ultrasound. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 79 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com LNA Gain Switch Response The LNA gain is programmable through SPI. The gain switching time depends on the SPI speed as well as the LNA gain response time. During the switching, glitches might occur and they can appear as artifacts in images. In addition, the signal chain needs about 14 us to settle after the LNA gain change. Thus LNA gain switching may not be preferred when switching time or settling time for the signal chain is limited. VOLTAGE-CONTROLLED-ATTENUATOR The attenuator in the AFE5809 is controlled by a pair of differential control inputs, the VCNTLM,P pins. The differential control voltage spans from 0 to 1.5 V. This control voltage varies the attenuation of the attenuator based on its linear-in-dB characteristic. Its maximum attenuation (minimum channel gain) appears at VCNTLP – VCNTLM = 1.5 V, and minimum attenuation (maximum channel gain) occurs at VCNTLP – VCNTLM = 0. The typical gain range is 40 dB and remains constant, independent of the PGA setting. When only single-ended VCNTL signal is available, this 1.5-Vpp signal can be applied on the VCNTLP pin with the VCNTLM pin connected to ground; As the below figures show, TGC gain curve is inversely proportional to the VCNTLP – VCNTLM. 1.5V VCNTLP VCNTLM = 0V X+40dB TGC Gain XdB (a) Single-Ended Input at VCNTLP 1.5V VCNTLP 0.75V VCNTLM 0V X+40dB TGC Gain XdB (b) Differential Inputs at VCNTLP and VCNTLM W0004-01 Figure 101. VCNTLP and VCNTLM Configurations 80 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 As discussed in the theory of operation, the attenuator architecture uses seven attenuator segments that are equally spaced in order to approximate the linear-in-dB gain-control slope. This approximation results in a monotonic slope; the gain ripple is typically less than ±0.5 dB. The control voltage input (VCNTLM,P pins) represents a high-impedance input. The VCNTLM,P pins of multiple AFE5809 devices can be connected in parallel with no significant loading effects. When the voltage level (VCNTLP – VCNTLM) is above 1.5 V or below 0 V, the attenuator continues to operate at its maximum attenuation level or minimum attenuation level respectively. TI recommends to limit the voltage from –0.3 to 2 V. When the AFE5809 operates in CW mode, the attenuator stage remains connected to the LNA outputs. Therefore, TI recommends to power down the VCA using the PDN_VCA register bit. In this case, VCNTLP-VCNTLM voltage does not matter. The AFE5809 gain-control input has a –3-dB bandwidth of approximately 800KHz. This wide bandwidth, although useful in many applications (for example fast VCNTL response), can also allow high-frequency noise to modulate the gain control input and finally affect the Doppler performance. In practice, this modulation can be avoided by additional external filtering (RVCNTL and CVCNTL) at VCNTLM,P pins as Figure 96 shows. However, the external filter's cutoff frequency cannot be kept too low as this results in low gain response time. Without external filtering, the gain control response time is typically less than 1 μs to settle within 10% of the final signal level of 1VPP (–6dBFS) output as indicated in Figure 51 and Figure 52. Typical VCNTLM,P signals are generated by an 8-bit to 12-bit 10-MSPS digital to analog converter (DAC) and a differential operation amplifier. TI’s DACs, such as TLV5626 and DAC7821/11 (10 MSPS/12 bit), could be used to generate TGC control waveforms. Differential amplifiers with output common mode voltage control (that is, THS4130 and OPA1632) can connect the DAC to the VCNTLM/P pins. The buffer amplifier can also be configured as an active filter to suppress low frequency noise. The VCNTLM/P circuit shall achieve low noise in order to prevent the VCNTLM/P noise being modulated to RF signals. TI recommends that VCNTLM/P noise is below 25 nV/rtHz at 1 kHz and 5 nV/rtHz at 50 kHz. In high channel count premium systems, the VCNTLM/P noise requirement is higher. More information can be found in the literatures SLOS318 and SBAA150. The VCNTL vs Gain curves can be found in Figure 2. The following table also shows the absolute gain vs VCNTL, which may help program DAC correspondingly. In PW Doppler and color Doppler modes, VCNTL noise should be minimized to achieve the best close-in phase noise and SNR. Digital VCNTL feature is implemented to address this need in the AFE5809. In the digital VCNTL mode, no external VCNTL is needed. Table 30. VCNTLP – VCNTLM vs Gain Under Different LNA and PGA Gain Settings (Low Noise Mode) VCNTLP – VCNTLM (V) Gain (dB) LNA = 12 dB PGA = 24 dB Gain (dB) LNA = 18 dB PGA = 24 dB Gain (dB) LNA = 24 dB PGA = 24 dB Gain (dB) LNA = 12 dB PGA = 30 dB Gain (dB) LNA = 18 dB PGA = 30 dB Gain (dB) LNA = 24 dB PGA = 30 dB 0 36.45 42.45 48.45 42.25 48.25 54.25 0.1 33.91 39.91 45.91 39.71 45.71 51.71 0.2 30.78 36.78 42.78 36.58 42.58 48.58 0.3 27.39 33.39 39.39 33.19 39.19 45.19 0.4 23.74 29.74 35.74 29.54 35.54 41.54 0.5 20.69 26.69 32.69 26.49 32.49 38.49 0.6 17.11 23.11 29.11 22.91 28.91 34.91 0.7 13.54 19.54 25.54 19.34 25.34 31.34 0.8 10.27 16.27 22.27 16.07 22.07 28.07 0.9 6.48 12.48 18.48 12.28 18.28 24.28 1.0 3.16 9.16 15.16 8.96 14.96 20.96 1.1 –0.35 5.65 11.65 5.45 11.45 17.45 1.2 –2.48 3.52 9.52 3.32 9.32 15.32 1.3 –3.58 2.42 8.42 2.22 8.22 14.22 1.4 –4.01 1.99 7.99 1.79 7.79 13.79 1.5 –4 2 8 1.8 7.8 13.8 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 81 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com CW OPERATION CW Summing Amplifier In order to simplify CW system design, a summing amplifier is implemented in the AFE5809 to sum and convert 8-channel mixer current outputs to a differential voltage output. Low noise and low power are achieved in the summing amplifier while maintaining the full dynamic range required in CW operation. This summing amplifier has 5 internal gain adjustment resistors which can provide 32 different gain settings (register 54[4:0], Figure 100 and Table 11). System designers can easily adjust the CW path gain depending on signal strength and transducer sensitivity. For any other gain values, an external resistor option is supported. The gain of the summation amplifier is determined by the ratio between the 500-Ω resistors after LNA and the internal or external resistor network REXT/INT. Thus the matching between these resistors plays a more important role than absolute resistor values. Better than 1% matching is achieved on chip. Due to process variation, the absolute resistor tolerance could be higher. If external resistors are used, the gain error between I/Q channels or among multiple AFEs may increase. TI recommends to use internal resistors to set the gain in order to achieve better gain matching (across channels and multiple AFEs). With the external capacitor CEXT , this summing amplifier has 1st order LPF response to remove high frequency components from the mixers, such as 2f0±fd. Its cut-off frequency is determined by: fHP = 1 2pRINT/EXT CEXT (15) Note that when different gain is configured through register 54[4:0], the LPF response varies as well. 82 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 CEXT REXT 250Ω 250Ω RINT 500Ω 1000Ω 2000Ω CW_AMPINP CW_AMPINM CW_OUTM I/V Sum Amp CW_OUTP 250Ω 250Ω 500Ω RINT 1000Ω 2000Ω REXT CEXT S0501-01 Figure 102. CW Summing Amplifier Block Diagram Multiple AFE5809s are usually utilized in parallel to expand CW beamformer channel count. These AFE5809 CW's voltage outputs can be summed and filtered externally further to achieve desired gain and filter response. AC coupling capacitors CAC are required to block DC component of the CW carrier signal. CAC can vary from 1 to 10 μF depending on the desired low frequency Doppler signal from slow blood flow. Multiple AFE5809s’ I/Q outputs can be summed together with a low noise external differential amplifiers before 16, 18-bit differential audio ADCs. The TI ultralow noise differential precision amplifier OPA1632 and THS4130 are suitable devices. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 83 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com An alternative current summing circuit is shown in Figure 104. However this circuit only achieves good performance when a lower noise operational amplifier is available compared to the AFE5809's internal summing differential amplifier. AFE No.4 AFE No.3 AFE No.2 ACT1 500 Ω INP1 INPUT1 INM1 AFE No.1 Mixer 1 Clock LNA1 500 Ω ACT2 500 Ω INP2 INPUT2 INM2 Ext Sum Amp Cext Mixer 2 Clock Rint/Rext CW_AMPINP CW_AMPINM LNA2 I/V Sum Amp CW_OUTM CW_OUTP Rint/Rext 500 Ω CAC RSUM Cext CW I or Q CHANNEL Structure ACT8 500 Ω INP8 INPUT8 INM8 Mixer 8 Clock LNA8 500 Ω S0502-01 Figure 103. CW Circuit With Multiple AFE5809s (Voltage Output Mode) Figure 104. CW Circuit With Multiple AFE5809s (Current Output mode) The CW I/Q channels are well matched internally to suppress image frequency components in Doppler spectrum. Low tolerance components and precise operational amplifiers should be used for achieving good matching in the external circuits as well. 84 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 NOTE The local oscillator inputs of the passive mixer are cos(ωt) for I-CH and sin(ωt) for Q-CH respectively. Depending on users' CW Doppler complex FFT processing, swapping I/Q channels in FPGA or DSP may be needed in order to get correct blood flow directions. CW Clock Selection The AFE5809 can accept differential LVDS, LVPECL, and other differential clock inputs as well as single-ended CMOS clock. An internally generated VCM of 2.5 V is applied to CW clock inputs, that is CLKP_16X/ CLKM_16X and CLKP_1X/ CLKM_1X. Since this 2.5 V VCM is different from the one used in standard LVDS or LVPECL clocks, AC coupling is required between clock drivers and the AFE5809 CW clock inputs. When CMOS clock is used, CLKM_1X and CLKM_16X should be tied to ground. Common clock configurations are illustrated in Figure 105. Appropriate termination is recommended to achieve good signal integrity. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 85 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com 3.3 V 130 Ω 83 Ω CDCM7005 CDCE7010 3.3 V 0.1 μF AFE CLOCKs 0.1 μF 130 Ω LVPECL (a) LVPECL Configuration 100 Ω CDCE72010 0.1 μF 0.1 μF AFE CLOCKs LVDS (b) LVDS Configuration 0.1μF 0.1μF CLOCK SOURCE 0.1μF AFE CLOCKs 50 Ω 0.1μF (c) Transformer Based Configuration CMOS CLK Driver AFE CMOS CLK CMOS (d) CMOS Configuration S0503-01 Figure 105. Clock Configurations The combination of the clock noise and the CW path noise can degrade the CW performance. The internal clocking circuit is designed for achieving excellent phase noise required by CW operation. The phase noise of the AFE5809 CW path is better than 155 dBc/Hz at 1-kHz offset. Consequently the phase noise of the mixer clock inputs needs to be better than 155 dBc/Hz. 86 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 In the 16/8/4 × ƒcw operations modes, low phase noise clock is required for 16, 8, 4 × ƒcw clocks (that is CLKP_16X/ CLKM_16X pins) in order to maintain good CW phase noise performance. The 1 × ƒcw clock (that is CLKP_1X/ CLKM_1X pins) is only used to synchronize the multiple AFE5809 chips and is not used for demodulation. Thus 1 × ƒcw clock’s phase noise is not a concern. However, in the 1 × ƒcw operation mode, low phase noise clocks are required for both CLKP_16X/ CLKM_16X and CLKP_1X/ CLKM_1X pins since both of them are used for mixer demodulation. In general, higher slew rate clock has lower phase noise; thus, clocks with high amplitude and fast slew rate are preferred in CW operation. In the CMOS clock mode, 5 V CMOS clock can achieve the highest slew rate. Clock phase noise can be improved by a divider as long as the divider’s phase noise is lower than the target phase noise. The phase noise of a divided clock can be improved approximately by a factor of 20logN dB where N is the dividing factor of 16, 8, or 4. If the target phase noise of mixer LO clock 1×fcw is 160dBc/Hz at 1KHz off carrier, the 16×fcw clock phase noise should be better than 160 – 20log16 = 136 dBc/Hz. TI’s jitter cleaners LMK048X/CDCM7005/CDCE72010 exceed this requirement and can be selected for the AFE5809. In the 4X/1X modes, higher quality input clocks are expected to achieve the same performance since N is smaller. Thus the 16X mode is a preferred mode since it reduces the phase noise requirement for system clock design. In addition, the phase delay accuracy is specified by the internal clock divider and distribution circuit. Note in the 16X operation mode, the CW operation range is limited to 8 MHz due to the 16X CLK. The maximum clock frequency for the 16X CLK is 128 MHz. In the 8X, 4X, and 1X modes, higher CW signal frequencies up to 15 MHz can be supported with small degradation in performance, for example the phase noise is degraded by 9 dB at 15 MHz, compared to 2 MHz. As the channel number in a system increases, clock distribution becomes more complex. It is not preferred to use one clock driver output to drive multiple AFEs since the clock buffer’s load capacitance increases by a factor of N. As a result, the falling and rising time of a clock signal is degraded. A typical clock arrangement for multiple AFE5809s is illustrated in Figure 106. Each clock buffer output drives one AFE5809 in order to achieve the best signal integrity and fastest slew rate, that is better phase noise performance. When clock phase noise is not a concern, for example the 1 × ƒcw clock in the 16, 8, 4 × ƒcw operation modes, one clock driver output may excite more than one AFE5809s. Nevertheless, special considerations should be applied in such a clock distribution network design. In typical ultrasound systems, it is preferred that all clocks are generated from a same clock source, such as 16 × ƒcw , 1 × ƒcw clocks, audio ADC clocks, RF ADC clock, pulse repetition frequency signal, frame clock, and so on. By doing this, interference due to clock asynchronization can be minimized. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 87 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com FPGA Clock/ Noisy Clock n×16×CW Freq LMK048X CDCE72010 CDCM7005 16X CW CLK 1X CW CLK CDCLVP1208 LMK0030X LMK01000 CDCLVP1208 LMK0030X LMK01000 AFE AFE AFE AFE 8 Synchronized 1X CW CLKs AFE AFE AFE AFE 8 Synchronized 16 X CW CLKs B0436-01 Figure 106. CW Clock Distribution CW Supporting Circuits As a general practice in CW circuit design, in-phase and quadrature channels should be strictly symmetrical by using well matched layout and high accuracy components. In systems, additional high-pass wall filters (20 to 500 Hz) and low-pass audio filters (10 KHz to 100 KHz) with multiple poles are usually needed. Since CW Doppler signal ranges from 20 Hz to 20 kHz, noise under this range is critical. Consequently low noise audio operational amplifiers are suitable to build these active filters for CW post-processing, that is OPA1632 or OPA2211. More filter design techniques can be found from www.ti.com. The TI active filter design tool http://focus.ti.com/docs/toolsw/folders/print/filter-designer.html. The filtered audio CW I/Q signals are sampled by audio ADCs and processed by DSP or PC. Although CW signal frequency is from 20 Hz to 20 KHz, higher sampling rate ADCs are still preferred for further decimation and SNR enhancement. Due to the large dynamic range of CW signals, high resolution ADCs (≥ 16 bit) are required, such as ADS8413 (2 MSPS, 16 bit, 92 dBFS SNR) and ADS8472 (1 MSPS/16 bit/95 dBFS SNR). ADCs for in-phase and quadature-phase channels must be strictly matched, not only amplitude matching but also phase matching, in order to achieve the best I/Q matching,. In addition, the in-phase and quadrature ADC channels must be sampled simultaneously. LOW FREQUENCY SUPPORT In addition, the signal chain of the AFE5809 can handle signal frequency lower than 100 kHz, which enables the AFE5809 to be used in both sonar and medical applications. The PGA integrator has to be turned off in order to enable the low frequency support. Meanwhile, a large capacitor like 1 µF can be used for setting low corner frequency of the LNA DC offset correction circuit as shown in Figure 77. AFE5809's low frequency response can be found in Figure 59. 88 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 ADC OPERATION ADC Clock Configurations To ensure that the aperture delay and jitter are the same for all channels, the AFE5809 uses a clock tree network to generate individual sampling clocks for each channel. The clock, for all the channels, are matched from the source point to the sampling circuit of each of the eight internal ADCs. The variation on this delay is described in the aperture delay parameter of the output interface timing. Its variation is given by the aperture jitter number of the same table. FPGA Clock/ Noisy Clock n × (20 to 65)MHz TI Jitter Cleaner LMK048X CDCE72010 CDCM7005 20 to 65 MHz ADC CLK CDCLVP1208 LMK0030X LMK01000 CDCE72010 has 10 outputs thus the buffer may not be needed for 64CH systems AFE AFE AFE AFE AFE AFE AFE AFE 8 Synchronized ADC CLKs B0437-01 Figure 107. ADC Clock Distribution Network The AFE5809 ADC clock input can be driven by differential clocks (sine wave, LVPECL or LVDS) or singled clocks (LVCMOS) similar to CW clocks as shown in Figure 105. In the single-end case, TI recommends that the use of low jitter square signals (LVCMOS levels, 1.8-V amplitude). See TI document SLYT075 for further details on the theory. The jitter cleaner CDCM7005 or CDCE72010 is suitable to generate the AFE5809’s ADC clock and ensure the performance for the14bit ADC with 77 dBFS SNR. A clock distribution network is shown in Figure 107. ADC Reference Circuit The ADC’s voltage reference can be generated internally or provided externally. When the internal reference mode is selected, the REFP/M becomes output pins and should be floated. When 3[15] = 1 and 1[13] = 1, the device is configured to operate in the external reference mode in which the VREF_IN pin should be driven with a 1.4-V reference voltage and REFP/M must be left open. Since the input impedance of the VREF_IN is high, no special drive capability is required for the 1.4-V voltage reference Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 89 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com The digital beam-forming algorithm in an ultrasound system relies on gain matching across all receiver channels. A typical system would have about 12 octal AFEs on the board. In such a case, it is critical to ensure that the gain is matched, essentially requiring the reference voltages seen by all the AFEs to be the same. Matching references within the eight channels of a chip is done by using a single internal reference voltage buffer. Trimming the reference voltages on each chip during production ensures that the reference voltages are wellmatched across different chips. When the external reference mode is used, a solid reference plane on a printed circuit board can ensure minimal voltage variation across devices. More information on voltage reference design can be found in the document SLYT339. The dominant gain variation in the AFE5809 comes from the VCA gain variation. The gain variation contributed by the ADC reference circuit is much smaller than the VCA gain variation. Hence, in most systems, using the ADC internal reference mode is sufficient to maintain good gain matching among multiple AFE5809s. In addition, the internal reference circuit without any external components achieves satisfactory thermal noise and phase noise performance. POWER MANAGEMENT Power/Performance Optimization The AFE5809 has options to adjust power consumption and meet different noise performances. This feature would be useful for portable systems operated by batteries when low power is more desired. Please refer to characteristics information listed in the table of electrical characteristics as well as the typical characteristic plots. Power Management Priority Power management plays a critical role to extend battery life and ensure long operation time. The AFE5809 has fast and flexible power down/up control which can maximize battery life. The AFE5809 can be powered down/up through external pins or internal registers. Table 31 indicates the affected circuit blocks and priorities when the power management is invoked. The higher priority controls can overwrite the lower priority controls. In the device, all the power down controls are logically ORed to generate final power down for different blocks. The higher priority controls can cover the lower priority controls. The digital demoduator also has 4 power down controls, PWRDWN_VCA_BYPASS, PWRDWN_ADC_BYPASS, PWRDWN_DIG_BYPASS, and PWRDWN_LVDS_BYPASS. Their priority is lower the controls listed inTable 31. Table 31. Power Management Priority Pin Name Blocks Priority PDN_GLOBAL All High Medium Pin PDN_VCA LNA + VCAT+ PGA Register VCA_PARTIAL_PDN LNA + VCAT+ PGA Low Register VCA_COMPLETE_PDN LNA + VCAT+ PGA Medium Medium Pin PDN_ADC ADC Register ADC_PARTIAL_PDN ADC Low Register ADC_COMPLETE_PDN ADC Medium Register PDN_VCAT_PGA VCAT + PGA Lowest Register PDN_LNA LNA Lowest Partial Power-Up and Power-Down Mode The partial power-up and power-down mode is also called as fast power-up and power-down mode. In this mode, most amplifiers in the signal path are powered down, while the internal reference circuits remain active as well as the LVDS clock circuit, that is the LVDS circuit still generates its frame and bit clocks. 90 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 The partial power down function allows the AFE5809 to be wake up from a low-power state quickly. This configuration ensures that the external capacitors are discharged slowly; thus a minimum wake-up time is needed as long as the charges on those capacitors are restored. The VCA wake-up response is typically about 2 μs or 1% of the power down duration whichever is larger. The longest wake-up time depends on the capacitors connected at INP and INM, as the wake-up time is the time required to recharge the caps to the desired operating voltages. For 0.1 μF at INP and 15 nF at INM can give a wake-up time of 2.5 ms. For larger capacitors this time will be longer. The ADC wake-up time is about 1 μs. Thus the AFE5809 wake-up time is more dependent on the VCA wake-up time. This also assumes that the ADC clock has been running for at least 50 µs before normal operating mode resumes. The power-down time is instantaneous, less than 1 µs. This fast wake-up response is desired for portable ultrasound applications in which the power saving is critical. The pulse repetition frequency of a ultrasound system could vary from 50KHz to 500 Hz, while the imaging depth (that is the active period for a receive path) varies from 10 μs to hundreds of µs. The power saving can be pretty significant when a system’s PRF is low. In some cases, only the VCA would be powered down while the ADC keeps running normally to ensure minimal impact to FPGAs. In the partial power-down mode, the AFE5809 typically dissipates only 26 mW/ch, representing an 80% power reduction compared to the normal operating mode. This mode can be set using either pins (PDN_VCA and PDN_ADC) or register bits (VCA_PARTIAL_PDN and ADC_PARTIAL_PDN). Complete Power-Down Mode To achieve the lowest power dissipation of 0.7 mW/CH, the AFE5809 can be placed into a complete power-down mode. This mode is controlled through the registers ADC_COMPLETE_PDN, VCA_COMPLETE_PDN or PDN_GLOBAL pin. In the complete power-down mode, all circuits including reference circuits within the AFE5809 are powered down; and the capacitors connected to the AFE5809 are discharged. The wake-up time depends on the time needed to recharge these capacitors. The wake-up time depends on the time that the AFE5809 spends in shutdown mode. 0.1 μF at INP and 15 nF at INM can give a wake-up time close to 2.5 ms. Power Saving in CW Mode Usually only half the number of channels in a system are active in the CW mode. Thus the individual channel control through ADC_PDN_CH <7:0> and VCA_PDN_CH <7:0> can power down unused channels and save power consumption greatly. Under the default register setting in the CW mode, the voltage controlled attenuator, PGA, and ADC are still active. During the debug phase, both the PW and CW paths can be running simultaneously. In real operation, these blocks need to be powered down manually. TEST MODES The AFE5809 includes multiple test modes to accelerate system development. The ADC test modes have been discussed in the register description section. The VCA has a test mode in which the CH7 and CH8 PGA outputs can be brought to the CW pins. By monitoring these PGA outputs, the functionality of VCA operation can be verified. The PGA outputs are connected to the virtual ground pins of the summing amplifier (CW_IP_AMPINM/P, CW_QP_AMPINM/P) through 5-kΩ resistors. The PGA outputs can be monitored at the summing amplifier outputs when the LPF capacitors CEXT are removed. Please note that the signals at the summing amplifier outputs are attenuated due to the 5-kΩ resistors. The attenuation coefficient is RINT/EXT / 5 kΩ. If users would like to check the PGA outputs without removing CEXT, an alternative way is to measure the PGA outputs directly at the CW_IP_AMPINM/P and CW_QP_AMPINM/P when the CW summing amplifier is powered down Some registers are related to this test mode. PGA Test Mode Enable: Reg59[9]; Buffer Amplifier Power Down Reg59[8]; and Buffer Amplifier Gain Control Reg54[4:0]. Based on the buffer amplifier configuration, the registers can be set in different ways: • • Configuration 1 – In this configuration, the test outputs can be monitored at CW_AMPINP/M – Reg59[9] = 1; Test mode enabled – Reg59[8] = 0; Buffer amplifier powered down Configuration 2 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 91 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 – – – – www.ti.com In this configuration, the test outputs can be monitored at CW_OUTP/M Reg59[9] = 1; Test mode enabled Reg59[8] = 1; Buffer amplifier powered on Reg54[4:0] = 10H; Internal feedback 2K resistor enabled. Different values can be used as well PGA_P Cext 5K ACT 500 Ω INP INPUT INM Mixer Clock Rint/Rext CW_AMPINP CW_AMPINM LNA 500 Ω CW_OUTM I/V Sum Amp Rint/Rext CW_OUTP 5K Cext PGA_M S0504-01 Figure 108. AFE5809 PGA Test Mode POWER SUPPLY, GROUNDING, AND BYPASSING In a mixed-signal system design, power supply and grounding design plays a significant role. The AFE5809 distinguishes between two different grounds: AVSS (analog ground) and DVSS (digital ground). In most cases, it should be adequate to lay out the printed circuit board (PCB) to use a single ground plane for the AFE5809. Care should be taken that this ground plane is properly partitioned between various sections within the system to minimize interactions between analog and digital circuitry. Alternatively, the digital (DVDD) supply set consisting of the DVDD and DVSS pins can be placed on separate power and ground planes. For this configuration, the AVSS and DVSS grounds should be tied together at the power connector in a star layout. In addition, optical isolator or digital isolators, such as ISO7240, can separate the analog portion from the digital portion completely. Consequently they prevent digital noise to contaminate the analog portion. Table 31 lists the related circuit blocks for each power supply. Table 32. Supply vs Circuit Blocks Power Supply Ground Circuit Blocks AVDD (3.3 VA) AVSS LNA, attenuator, PGA with clamp and BPF, reference circuits, CW summing amplifier, CW mixer, VCA SPI AVDD_5V (5 VA) AVSS LNA, CW clock circuits, reference circuits AVDD_ADC (1.8 VA) AVSS ADC analog and reference circuits DVDD (1.8 VD) DVSS LVDS and ADC SPI All bypassing and power supplies for the AFE5809 should be referenced to their corresponding ground planes. All supply pins should be bypassed with 0.1-µF ceramic chip capacitors (size 0603 or smaller). In order to minimize the lead and trace inductance, the capacitors should be located as close to the supply pins as possible. Where double-sided component mounting is allowed, these capacitors are best placed directly under the package. In addition, larger bipolar decoupling capacitors 2.2 to 10 µF, effective at lower frequencies) may also be used on the main supply pins. These components can be placed on the PCB in proximity (< 0.5 inch or 12.7 mm) to the AFE5809 itself. 92 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 The AFE5809 has a number of reference supplies needed to be bypassed, such as CM_BYP and VHIGH . These pins should be bypassed with at least 1µF; higher value capacitors can be used for better low-frequency noise suppression. For best results, choose low-inductance ceramic chip capacitors (size 0402, > 1 µF) and place them as close as possible to the device pins. High-speed mixed signal devices are sensitive to various types of noise coupling. One primary source of noise is the switching noise from the serializer and the output buffer/drivers. For the AFE5809, care has been taken to ensure that the interaction between the analog and digital supplies within the device is kept to a minimal amount. The extent of noise coupled and transmitted from the digital and analog sections depends on the effective inductances of each of the supply and ground connections. Smaller effective inductance of the supply and ground pins leads to improved noise suppression. For this reason, multiple pins are used to connect each supply and ground sets. It is important to maintain low inductance properties throughout the design of the PCB layout by use of proper planes and layer thickness. BOARD LAYOUT Proper grounding and bypassing, short lead length, and the use of ground and power-supply planes are particularly important for high-frequency designs. Achieving optimum performance with a high-performance device such as the AFE5809 requires careful attention to the PCB layout to minimize the effects of board parasitics and optimize component placement. A multilayer PCB usually ensures best results and allows convenient component placement. In order to maintain proper LVDS timing, all LVDS traces should follow a controlled impedance design. In addition, all LVDS trace lengths should be equal and symmetrical; TI recommends to keep trace length variations less than 150 mil (0.150 inch or 3.81 mm). To avoid noise coupling through supply pins, TI recommends to keep sensitive input pins, such as INM, INP, ACT pins aways from the AVDD 3.3 V and AVDD_5V planes. For example, either the traces or vias connected to these pins should not be routed across the AVDD 3.3 V and AVDD_5V planes. That is to avoid power planes under INM, INP, and ACT pins. In addition, appropriate delay matching should be considered for the CW clock path, especially in systems with high channel count. For example, if clock delay is half of the 16x clock period, a phase error of 22.5°C could exist. Thus the timing delay difference among channels contributes to the beamformer accuracy. Additional details on BGA PCB layout techniques can be found in the Texas Instruments Application Report MicroStar BGA Packaging Reference Guide (SSYZ015), which can be downloaded from www.ti.com. Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 93 AFE5809 SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 www.ti.com REVISION HISTORY Changes from Revision C (January 2013) to Revision D Page • Changed Feature: Decimation Filter Factor M = 1 to 64To: ...M = 1 to 32 .......................................................................... 1 • Added a note for new silicon features. ................................................................................................................................. 2 • Changed pin description of CLKM_16X from "In the 1X CW clock mode, this pin becomes the quadrature-phase 1X CLKM for the CW mixer" to "... in-phase 1X CLKM for the CW mixer" ................................................................................ 5 • Changed pin description of CLKP_16X from "In the 1X CW clock mode, this pin becomes the quadrature-phase 1X CLKP for the CW mixer" to "... in-phase 1X CLKP for the CW mixer" ................................................................................. 5 • Changed pin description of CLKM_1X from "In the 1X CW clock mode, this pin becomes the in-phase 1X CLKP for the CW mixer" to "... quadrature-phase 1X CLKP for the CW mixer" .................................................................................. 5 • Changed pin description of CLKP_1X from "In the 1X CW clock mode, this pin becomes the in-phase 1X CLKP for the CW mixer" to "... quadrature-phase 1X CLKP for the CW mixer" .................................................................................. 5 • Corrected AVDD_5V current from 16.5 mA to 26 mA. ....................................................................................................... 11 • Changed 64X decimation factor to 32X decimation factorin DVDD consumption at 65 MSPS in DIGITAL DEMODULATOR ELECTRICAL CHARACTERISTICS ...................................................................................................... 12 • Changed 64X decimation factor to 32X decimation factor in DVDD consumption at 40 MSPS in DIGITAL DEMODULATOR ELECTRICAL CHARACTERISTICS ...................................................................................................... 12 • Changed Input Clock to Bit Clock ....................................................................................................................................... 24 • Changed Input Clock to Bit Clock ....................................................................................................................................... 24 • Corrected a typo in Reg0x2[15:13], that is changed 0x2[15:3] to 0x2[15:13] .................................................................... 30 • Added a note to Reg0x15[0] "This HPF feature is only avaiable when the demodulation block is disabled." ................... 31 • Added a note to Reg0x21[0] "This HPF feature is only available when the demodulation block is disabled." .................. 32 • Added a note "These digital processing features are only avaiable when the demodulation block is disabled." .............. 33 • Added a note in the Reg 51[3:1] description,"Please note: 0x3D[14], that is 5MHz LPF, should be set a 0. " ................. 36 • Added a note in the Reg 57[7:5] description,"Note: Reg.61[15] should be set as 0; otherwise PGA_CLAMP_LEVEL is affected by Reg. 61[15]." ................................................................................................................................................. 36 • Added Reg 61[15:13] description. ...................................................................................................................................... 38 • Added and reorganized Description of LNA Input Impedances Configuration ................................................................... 40 • Added Table 10 .................................................................................................................................................................. 41 • Added a note for Reg0x1F[5:0] "it is from 1 to 32." ............................................................................................................ 47 • Highlighted the note about Channel Selection. .................................................................................................................. 48 • Added Figure 67 ................................................................................................................................................................. 49 • Changed "0x521" to "0x121F" inRF Mode .......................................................................................................................... 54 • Changed "MODULATE_BYPASS = 1" to "MODULATE_BYPASS = 0" inRF Mode .......................................................... 54 • Added "FIR Filter Delay vs. TX_TRIG Timing" and "Expression of Decimation Filter Response" ..................................... 56 • Updated figure reference and added a link in Expression of Decimation Filter Response. ............................................... 59 • Added text " In high channel count premium systems, the VCNTLM/P noise requirement is higher." ................................... 81 • Deleted "VREF_IN" from "The AFE5809 has a number of reference supplies needed to be bypassed." ......................... 93 • Added "That is to avoid power planes under INM, INP, and ACT pins." ............................................................................ 93 Changes from Revision B (September 2012) to Revision C Page • Changed 'SIN' to '-SIN' and 'C8' to 'Cn' in Figure 1 .............................................................................................................. 3 • Added a note "The above timing data can be applied to 12-bit or 16-bit LVDS rates" ...................................................... 24 • Changed SPI pull down resistors from "100 kΩ" to "20 kΩ". .............................................................................................. 27 • Added a note to register 0x3[14:13] "Make sure the settings aligning with the demod register 0x3[14:13]" ..................... 31 • Added Note to PGA_CLAMP_LEVEL: "The maximum PGA output level can exceed 2Vpp with the clamp circuit enabled.". ............................................................................................................................................................................ 36 94 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 AFE5809 www.ti.com SLOS738D – SEPTEMBER 2012 – REVISED JANUARY 2014 • Changed List item From: "The internal 32 bit filter output" To: The internal 36 bit filter output" ........................................ 51 • Changed text following Table 25 From: "the block index, from 0 to (-1)" To: "the block index, from 0 to (M – 1) ............. 53 • Changed from "For RF mode (passing 14 bits only)... 0xC3[14:13] to ‘00’ " to "...0xC3[14:13] to ‘10’ " in LVDS Serialization Factor ............................................................................................................................................................. 53 • Added "The maximum PGA output level can be above 2 Vpp even with the clamp circuit enabled" in the PGA description. .......................................................................................................................................................................... 64 • Added a note "The local oscillator inputs of the passive mixer are cos(ωt) for I-CH and sin(ωt) for Q-CH" ...................... 65 • Changed "10Ω" to "10-15Ω " in Figure 82 .......................................................................................................................... 66 • Added a NOTE "The digital demodulator is based on a conventional down converter, that is, -sin(ω0t) is used for Q phase. ................................................................................................................................................................................. 72 • Added text "TI recommends that VCNTLM/P noise is below 25 nV/rtHz at 1KHz and 5 nV/rtHz at 50 kHz. " ....................... 81 • Added a note "The local oscillator inputs of the passive mixer are cos(ωt) for I-CH and sin(ωt) for Q-CH " .................... 85 • Added "AVDD_5V needs to be away from sensitive input pins" ........................................................................................ 93 Changes from Revision A (September 2012) to Revision B Page • Deleted Feature: "Programmable Digital I/Q Demodulator" ................................................................................................. 1 • Changed Feature: Noise, Power Optimizations (Without Digital Demodulator) From: 99 mW/CH at 1.1 nV/rtHz, 40 MSPS To: 101 mW/CH at 1.1 nV/rtHz, 40 MSPS ................................................................................................................ 1 • Changed Feature: Excellent Device-to-Device Gain Matching From: ±0.5 dB (typical) and ±0.9 dB (max) To: ±0.5 dB (typical) and ±1 dB (max) ................................................................................................................................................ 1 • Changed Gain matching values From MIN = –0.9 dB to MIN = –1 dB and From: MAX = 0.9 dB to MAX = 1 dB .............. 9 • Added a note to PGA_CLAMP_LEVEL: "in the low power and medium power modes, PGA_CLAMP is disabled for saving power if 51[7] = 0" ................................................................................................................................................... 36 • Added Note: "In the low power and medium power modes, PGA_CLAMP is disabled for saving power if 51[7]=0" ........ 64 Changes from Original (September 2012) to Revision A • Page Changed the device From: Product Preview To: Production ................................................................................................ 1 Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated Product Folder Links: AFE5809 95 PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2014 PACKAGING INFORMATION Orderable Device Status (1) AFE5809ZCF ACTIVE Package Type Package Pins Package Drawing Qty NFBGA ZCF 135 160 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Green (RoHS & no Sb/Br) SNAGCU Level-3-260C-168 HR Op Temp (°C) Device Marking (4/5) 0 to 85 AFE5809 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2014 Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2014, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: AFE5809EVM