CEL CG2185X2 6ghz middle power spdt switch Datasheet

RF SWITCH
CG2185X2
6GHz
Power SPDTName
Switch
EnterMedium
a Short Document/Title
Here
DESCRIPTION

PACKAGE
The CG2185X2 is a pHEMT GaAs FET SPDT
(Single Pole Double Throw) Switch. This device can
operate from 2.0GHz to 6.0GHz, with low insertion
loss and high isolation.

6-pin plastic Thin Small SON (XS02) Package
(1.0mm x 1.0mm x 0.37mm)
FEATURES




Control voltage :
VC(H) = 1.8 to 5.0 V (3.0V TYP.)
VC(L) = -0.2 to 0.2 V (0V TYP.)
Low insertion loss :
Lins1 = 0.35 dB TYP. @ f = 2.0 to 2.5 GHz
Lins2 = 0.40 dB TYP. @ f = 4.9 to 6.0 GHz
High isolation :
ISL1 = 28 dB TYP. @ f = 2.0 to 2.5 GHz
ISL2 = 26 dB TYP. @ f = 4.9 to 6.0 GHz
Power handling :
Pin(1dB) = +32 dBm TYP.
@ VC(H) = 3.0 V, VC(L) = 0 V
APPLICATIONS



Bluetooth
Wireless LAN (IEEE802.11a/b/g/n/ac)
ISM band radios
ORDERING INFORMATION
Part Number
Order Number
CG2185X2
CG2185X2-C2
CG2185X2-EVAL
CG2185X2-EVAL
This document is subject to change without notice.
Date Published: January 2017
CDS-0004-02 (Issue D)
Package
Marking
6-pin plastic
TSSON (XS02)
(Pb-Free)
C1
Description
• Embossed tape 8 mm wide
• Pin 1, 6 face the perforation
side of the tape
• MOQ 10 kpcs/reel
• Evaluation Board with DC
block capacitors, power
supply bypass capacitors,
and RF and DC connectors
• MOQ 1
1
CG2185X2
PIN CONFIGURATION AND
INTERNAL BLOCK DIAGRAM
TRUTH TABLE
VC1
VC2
RFC-RF1
RFC-RF2
High
Low
OFF
ON
Low
High
ON
OFF
ABSOLUTE MAXIMUM RATINGS
(TA = +25˚C, unless otherwise specified)
Parameter
Symbol
Control Voltage
Rating
Unit
Note 1
V
Note 2
dBm
6.0
VC
Input Power
Pin
+33
Operating Ambient Temperature
TA
-45~+85
˚C
Storage Temperature
Tstg
-55~+150
˚C
Note
1. |VC1 - VC2|≦6.0V
2. 3.0V≦|VC1 - VC2|≦5.0V
RECOMMENDED OPERATING RANGE
(TA = +25˚C, unless otherwise specified)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
f
2.0
-
6.0
GHz
Switch Control Voltage (H)
VC(H)
+1.8
+3.0
+5.0
V
Switch Control Voltage (L)
VC(L)
-0.2
0
+0.2
V
Operating Frequency
This document is subject to change without notice.
2
CG2185X2
ELECTRICAL CHARACTERISTICS
(TA=+25˚C, VC(H)=3.0V, VC(L)=0V, Zo=50Ω, DC Block Capacitance=8pF, unless otherwise specified)
Parameter
Insertion Loss
Isolation
Input Return Loss
Output Return Loss
0.1 dB Loss Compression
Input Power
Note 1
1 dB Loss Compression Input
Power
Note 2
Symbol
Test Conditions
MIN.
TYP.
MAX.
Unit
Lins1
f = 2.0 to 2.5 GHz
-
0.35
0.55
dB
Lins2
f = 4.9 to 6.0 GHz
-
0.40
0.60
dB
ISL1
f = 2.0 to 2.5 GHz
25
28
-
dB
ISL2
f = 4.9 to 6.0 GHz
23
26
-
dB
RLin1
f = 2.0 to 2.5 GHz
23
26
-
dB
RLin2
f = 4.9 to 6.0 GHz
15
18
-
dB
RLout1
f = 2.0 to 2.5 GHz
21
24
-
dB
RLout2
f = 4.9 to 6.0 GHz
15
18
-
dB
+20
+23
-
dBm
+26
+29
-
dBm
+19
+22
-
dBm
+26
+29
-
dBm
+24
+27
-
dBm
+29
+32
-
dBm
+22
+25
-
dBm
+29
+32
-
dBm
-
+55
-
dBm
Pin(0.1 dB)
Pin(1 dB)
3rd Order Input
Intercept Point
IIP3
f = 2.5 GHz, VC(H)=1.8V,
VC(L)=0V
f = 2.5 GHz, VC(H)=3.0V,
VC(L)=0V
f = 6.0 GHz, VC(H)=1.8V,
VC(L)=0V
f = 6.0 GHz VC(H)=3.0V,
VC(L)=0V
f = 2.5 GHz, VC(H)=1.8V,
VC(L)=0V
f = 2.5 GHz, VC(H)=3.0V,
VC(L)=0V
f = 6.0 GHz, VC(H)=1.8V,
VC(L)=0V
f = 6.0 GHz VC(H)=3.0V,
VC(L)=0V
f = 2.5GHz
2-tone 5MHz Spacing
Switching Speed
tsw
50% CTL to 90/10%
-
50
150
ns
Switch Control Current
Icont
RF None
-
2
10
μA
Note 1. Pin(0.1dB) is the measured input power level when the insertion loss increases 0.1dB more than that of the
linear range.
2. Pin(1dB) is the measured input power level when the insertion loss increases 1dB more than that of the
linear range.
This document is subject to change without notice.
3
CG2185X2
EVALUATION CIRCUIT
1,000pF
VC2
4
3
5
2
6
1
8pF
RF2
8pF
RFC
VC1
RF1
8pF
1,000pF
The application circuits and their parameters are for reference only and are not intended for use in actual designs.
DC Blocking Capacitors are required at all RF ports.
PACKAGE DIMENSIONS
6-pin Plastic TSSON (XS02) (Unit: mm)
(Bottom View)
1.0
0.15
0.175
1.0
This document is subject to change without notice.
(Side View)
0.15 0.45
0.35
1.0
0.35
(Top View)
4
0.37
CG2185X2
RECOMMENDED SOLDERING CONDITIONS
Recommended Soldering Conditions are available on the CEL’s Part Summary page under Associated Documents
This document is subject to change without notice.
5
CG2185X2
REVISION HISTORY
Version
Change to current version
Page(s)
CDS-0004-02 (Issue A)
February 17, 2016
CDS-0004-02 (Issue B)
March 24, 2016
Initial datasheet
N/A
CDS-0004-02 (Issue C)
August 11, 2016
Removed “preliminary”
All
CDS-0004-02 (Issue D)
January 11, 2017
Added “Recommended Soldering Conditions” section
5
Added Eval Board ordering information.
Updated Marking information.
This document is subject to change without notice.
6
Page 1,2
CG2185X2
[CAUTION]
・ All information included in this document is current as of the date this document is issued. Such information,
however, is subject to change without any prior notice.
・ You should not alter, modify, copy, or otherwise misappropriate any CEL product, whether in whole or in part.
・ CEL does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of
third parties by or arising from the use of CEL products or technical information described in this document. No
license, expressed, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual
property rights of CEL or others.
・ Descriptions of circuits, software and other related information in this document are provided only to illustrate the
operation of semiconductor products and application examples. You are fully responsible for the incorporation of
these circuits, software, and information in the design of your equipment. CEL assumes no responsibility for any
losses incurred by you or third parties arising from the use of these circuits, software, or information.
・ CEL has used reasonable care in preparing the information included in this document, but CEL does not warrant
that such information is error free. CEL assumes no liability whatsoever for any damages incurred by you resulting
from errors in or omissions from the information included herein.
・ Although CEL endeavors to improve the quality and reliability of its products, semiconductor products have specific
characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions.
Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or
damage caused by fire in the event of the failure of a CEL product, such as safety design for hardware and software
including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging
degradation or any other appropriate measures
Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final
products or system manufactured by you.
・ Please use CEL products in compliance with all applicable laws and regulations that regulate the inclusion or use of
controlled substances, including without limitation, the EU RoHS Directive.
CEL assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and
regulations.
・ This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent
of CEL.
・ Please contact CEL if you have any questions regarding the information contained in this document or CEL
products, or if you have any other inquiries.
This document is subject to change without notice.
7
CG2185X2
[CAUTION]
This product uses gallium arsenide (GaAs) of the toxic substance appointed in laws and ordinances.
GaAs vapor and powder are hazardous to human health if inhaled or ingested.
・ Do not dispose in fire or break up this product.
・ Do not chemically make gas or powder with this product.
・ When discarding this product, please obey the laws of your country.
・ Do not lick the product or in any way allow it to enter the mouth.
[CAUTION]
Although this device is designed to be as robust as possible, ESD (Electrostatic Discharge) can
damage this device. This device must be protected at all times from ESD. Static charges may easily
produce potentials of several kilovolts on the human body or equipment, which can discharge
without detection. Industry-standard ESD precautions should be used at all times.
CEL Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054 • Tel: (408) 919-2500 • www.cel.com
For a complete list of sales offices, representatives and distributors,
Please visit our website: www.cel.com/contactus
For inquiries email us at [email protected]
This document is subject to change without notice.
8
Similar pages