Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type for Choke) Data Sheet Chip Inductor (Chip Coil) 1 Power Inductor (Wire Wound Type for Choke) LQH32C_53 Series (1210 Size) ■ Dimensions ■ Packaging 2.5±0.2 1.55±0.15 2.5±0.2 A A Code Packaging Minimum Quantity L 180mm Embossed Tape 2000 K 330mm Embossed Tape 7500 3.2±0.3 2.5±0.2 A : 2.8 max. 0.9±0.3 1.3±0.2 0.9±0.3 (in mm) ■ Rated Value (p: packaging code) Part Number Inductance Test Frequency Rated Current DC Resistance Self Resonance Frequency (min.) LQH32CN1R0M53p 1.0µH±20% 1MHz 1000mA 0.060ohm±30% 100MHz LQH32CN2R2M53p 2.2µH±20% 1MHz 790mA 0.097ohm±30% 64MHz LQH32CN3R3M53p 3.3µH±20% 1MHz 710mA 0.12ohm±30% 50MHz LQH32CN4R7M53p 4.7µH±20% 1MHz 650mA 0.15ohm±30% 43MHz LQH32CN6R8M53p 6.8µH±20% 1MHz 540mA 0.25ohm±30% 32MHz LQH32CN100K53p 10µH±10% 1MHz 450mA 0.30ohm±30% 26MHz LQH32CN150K53p 15µH±10% 1MHz 300mA 0.58ohm±30% 26MHz LQH32CN220K53p 22µH±10% 1MHz 250mA 0.71ohm±30% 19MHz LQH32CN330K53p 33µH±10% 1MHz 200mA 1.1ohm±30% 17MHz LQH32CN470K53p 47µH±10% 1MHz 170mA 1.3ohm±30% 15MHz LQH32CN680K53p 68µH±10% 1MHz 130mA 2.2ohm±30% 12MHz LQH32CN101K53p 100µH±10% 1MHz 100mA 3.5ohm±30% 10MHz Class of Magnetic Shield: No magnetic shield Operating Temperature Range: -40°C to +85°C Continued on the following page. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type for Choke) Data Sheet 2 Continued from the preceding page. ■ Impedance-Frequency Characteristics (Typ.) ■ Inductance-Current Characteristics (Typ.) 100 1000 100uH 10 100uH Inductance (µH) Impedance (kΩ) 100 10uH 1 1.0uH 0.1 10uH 10 1.0uH 1 0.01 0.001 0.1 1 10 100 1000 1 Frequency (MHz) 10 100 1000 Current (mA) ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/