IDT IDTQS32X861 High-speed cmos 20-bit bus switch with flow-thru pinout Datasheet

IDTQS32X861
HIGH-SPEED CMOS 20-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH® PRODUCTS
HIGH-SPEED CMOS
20-BIT BUS SWITCH
WITH FLOW-THRU PINOUT
DESCRIPTION:
FEATURES:
•
•
•
•
•
The QS32X861 provides two sets of ten high-speed CMOS TTLcompatible bus switches. The low ON resistance of the QS32X861 allows
inputs to be connected to outputs without adding propagation delay and
without generating additional ground bounce noise. The Bus Enable (BEn)
signals turn the switches on.
The QS32X861 bus switch is ideal for switching digital buses, as well as
for hotplug buffering and 5V to 3V conversion.
The QS32X861 is characterized for operation at -40°C to +85°C.
Enhanced N channel FET with no inherent diode to Vcc
Ω bidirectional switches connect inputs to outputs
5Ω
Zero propagation delay, zero ground bounce
Undershoot clamp diodes on all switch and control inputs
Available in 48-pin QVSOP package
APPLICATIONS:
•
•
•
•
•
•
IDTQS32X861
Hot-swapping, hot-docking
Voltage translation (5V to 3.3V)
Power conservation
Capacitance reduction and isolation
Bus isolation
Clock gating
FUNCTIONAL BLOCK DIAGRAM
A0
B0
A9
B9
BE1
A10
B10
A19
B19
BE2
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
c
2011 Integrated Device Technology, Inc.
JUNE 2011
1
DSC-5730/4
IDTQS32X861
HIGH-SPEED CMOS 20-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
PIN CONFIGURATION
INDUSTRIAL TEMPERATURE RANGE
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
Description
Max
Unit
VTERM(2)
Supply Voltage to Ground
–0.5 to +7
V
VTERM(3)
DC Switch Voltage Vs
–0.5 to +7
V
VTERM(3)
DC Input Voltage VIN
–0.5 to +7
V
NC
1
48
VCC
A0
2
47
BE1
A1
3
46
B0
VAC
V
4
45
B1
AC Input Voltage (pulse width ≤ 20ns)
–3
A2
IOUT
DC Output Current
120
mA
0.5
W
–65 to +150
°C
A3
5
44
B2
PMAX
Maximum Power Dissipation (TA = 85°C)
A4
6
43
B3
TSTG
Storage Temperature
A5
7
42
B4
A6
8
41
B5
A7
9
40
B6
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. Vcc terminals.
3. All terminals except Vcc.
A8
10
39
B7
A9
11
38
B8
GND
12
37
B9
NC
13
36
VCC
A10
14
35
BE2
A11
15
34
B10
A12
16
33
B11
A13
17
32
B12
A14
18
31
B13
Pins
Typ.
Max.(1)
Unit
A15
19
30
B14
Control Pins
3
5
pF
A16
20
29
B15
5
7
pF
A17
21
28
B16
A18
22
27
B17
A19
23
26
B18
GND
24
25
B19
QVSOP
TOP VIEW
CAPACITANCE
(TA = +25°C, f = 1.0MHZ, VIN = 0V, VOUT = 0V)
Quickswitch Channels (Switch OFF)
NOTE:
1. This parameter is measured at characterization but not tested.
PIN DESCRIPTION
Pin Names
I/O
Description
A0 - A19
I/O
Bus A
B0 - B19
I/O
Bus B
BEn
I
Bus Enable
FUNCTION TABLE(1)
BE1
BE2
A0 - A9
A10 - A19
Function
L
L
B0 - B9
B10 - B19
Connect
L
H
B0 - B9
Z
Connect
H
L
Z
B10 - B19
Connect
H
H
Z
Z
Disconnect
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
Z = High-Impedance
2
IDTQS32X861
HIGH-SPEED CMOS 20-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: TA = –40°C to +85°C, VCC = 5.0V ±5%
Symbol
Parameter
Test Conditions
Min.
Typ.(1)
Max.
Unit
2
—
—
V
VIH
Input HIGH Level
Guaranteed Logic HIGH for Control Pins
VIL
Input LOW Level
Guaranteed Logic LOW for Control Pins
—
—
0.8
V
IIN
Input LeakageCurrent (Control Inputs)
0V ≤ VIN ≤ VCC
—
±0.01
±1
μA
IOZ
Off-State Output Current (Hi-Z)
0V ≤ VOUT ≤ VCC, Switches OFF
—
±0.01
±1
μA
RON
Switch ON Resistance
Pass Voltage(2)
—
—
3.7
5
10
4
7
15
4.2
Ω
VP
VCC = Min., VIN = 0V, ION = 30mA
VCC = Min., VIN = 2.4V, ION =15mA
VCC = 5V, IOUT = -5μA
NOTES:
1. Typical values are at VCC = 5.0V, TA = 25°C.
2. Pass Voltage is guaranteed but not production tested.
TYPICAL ON RESISTANCE vs VIN AT VCC = 5V
16
R ON
(ohms)
14
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
V IN
(Volts)
3
2.5
3.0
3.5
V
IDTQS32X861
HIGH-SPEED CMOS 20-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
Test Conditions(1)
Parameter
Typ(2)
Max.
Unit
ICCQ
Quiescent Power Supply Current
VCC = Max., VIN = GND or Vcc, f = 0
0.2
6
μA
ΔICC
Power Supply Current per Control Input HIGH(3)
VCC = Max., VIN = 3.4V, f = 0
—
2.5
mA
ICCD
Dynamic Power Supply Current per MHz(4)
VCC = Max., A and B pins open
—
0.25
mA/MHz
BEn Control Input Toggling at 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Typical values are at VCC = 5.0V, 25°C ambient.
3. Per TLL driven input (VIN = 3.4V, control inputs only). A and B pins do not contribute to ΔIcc.
4. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B pins generate no significant
AC or DC currents as they transition. This parameter is guaranteed but not production tested.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
TA = -40°C to +85°C, VCC = 5.0V ± 5%;
CLOAD = 50pF, RLOAD = 500Ω unless otherwise noted.
Symbol
Parameter
tPLH
Data Propagation Delay (2,3)
tPHL
An to/from Bn
tPZH
Switch Turn-on Delay
tPZL
BEn to An/Bn
tPHZ
Switch Turn-off Delay (2)
tPLZ
BEn to An/Bn
Min. (1)
Typ.
Max.
Unit
—
0.25
—
ns
1.5
—
6.5
ns
1.5
—
5.5
ns
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.25ns for CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
the driven side.
4
IDTQS32X861
HIGH-SPEED CMOS 20-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
QS
XXXXX
Device Type
XX
Package
X
Process
X
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
Blank
8
Tube or Tray
Tape and Reel
Blank
Industrial (-40°C to +85°C)
Q1G
QVSOP - Green
32X861
High Speed CMOS 20-Bit Bus Switch
with Flow-Through Pinout
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
5
for Tech Support:
[email protected]
Similar pages