FTR-K1 SERIES POWER RELAY 1 POLE - 10A High Power Relay JV-KS Series n FEATURES Low profile and space saving - Height: 12.5 mm - Mounting space: 175 mm2 l High insulation - Insulation distance: 8 mm - Dielectric strength: 5,000 VAC - Surge strength: 10,000 V l Plastic materials - UL94 flame class V-0 l Plastic sealed type l Cadmium free relay l RoHS compliant. Please see page 5 for more information l n PARTNUMBER INFORMATION [Example] JV (a) 12 S - K S (b) (c) (d) (e) JV (a) Relay type : JV Series (b) ����������� Coil rated voltage����� ������������ 12 ���� ��: 3.....24 VDC ��������� ��� ���������������������������� Coil rating table at page 3� (c) Coil type S : 250mW (d) Enclosure K :� Plastic ��������������� sealed type ������ (e) Special type S : High power type Note: Actual marking omits the hyphen (-) or (*) FTR-K1SERIES SERIES JV-KS n SPECIFICATION Item Contact Data Life Coil Data Timing Data Insulation JV-KS Configuration 1 form A (SPST-NO) Construction Single Material AgSnO2 Resistance (initial) ≤ 70 mΩ at 6 VDC, 1A Contact rating (resistive) 10A, 250VAC / 24VDC Max. carrying current 10A Max. switching voltage 250VAC / 150VDC Max. switching power 2,500VA / 240W Min. switching load * 100mA, 5 VDC Mechanical 50 x 106 operations minimum Electrical 50 x 103 operations minimum Rated power (at 20 °C) 250mW Operating temperature range -40 °C to +70 °C (no frost) Operate (at nominal voltage) ≤ 8 ms (no bounce included) Release (at nominal voltage) ≤ 4 ms Resistance (initial) ≥ 1,000MOhm at 500VDC Dielectric strength Surge strength Other Vibration resistance Shock Weight Open contacts 750VAC, 1 min. Contacts to coil 5,000VAC, 1 min. Coil to contacts 10,000V / 1.2 x 50µs standard wave Misoperation 10 to 55Hz double amplitude 1.65 mm Endurance 10 to 55Hz double amplitude 5 mm Misoperation Min. 100m/s² (11 ± 1ms) Endurance Min. 1,000m/s² (6 ± 1ms) Approximately 4.3 g * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. JV-KS FTR-K1SERIES SERIES n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseVoltage (VDC) * 3 3 36 2.1 0.3 5 5 100 3.5 0.5 6 6 144 4.2 0.6 9 9 324 6.3 0.9 12 12 576 8.4 1.2 18 18 1296 12.6 1.8 24 24 2304 14.9 2.4 Rated Power (mW) 250 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) CSA C22.2 No. 14 10A, 24VDC, resistive 50,000 operations 10A, 250VAC, resistive 50,000 operations TV-4, 120VAC, 25,000 operations VDE 0435, 0631, 0860 40016247 10A, 30VDC, 100,000 operations, - 40 / 85 °C 10A, 250VAC, 25,000 operations, - 40 / 85 °C FTR-K1SERIES SERIES JV-KS n DIMENSIONS l Dimensions l Schematics (BOTTOM VIEW) l PC board mounting hole layout (BOTTOM VIEW) Unit: mm FTR-K1 SERIES JV-KS SERIES RoHS Compliance and Lead Free Information 1. General Information l l l l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile Recommended solder Sn-3.0Ag-0.5Cu. l Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. l 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. l FTR-K1 SERIES JV-KS SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2009 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. November 6, 2009