MTDA40A SERIES 40W Desktop Power Supply for I.T. Equipment 1 Year Warranty Wide Input Voltage 90 to 264 VAC, 47 to 63Hz IEC-320-C14 Input Inlet Output Voltage Available From 5VDC Thru 48VDC Single Output Class I Insulation Energy Star 2.0, CEC V, and RoHS compliance Approvals: Single Output Product Number Output Voltage Max. Output Current Total Regulation Maximum Output Power 5.00 A 5.00 ~ 3.75 A 4.375 ~ 3.18 A 3.64 ~ 3.07 A 3.07 ~ 2.50 A 2.50 ~ 1.90 A 1.90 ~ 1.48 A 1.48 ~ 1.21 A 1.21 ~ 1.00 A 1.00 ~ 0.83 A 5% 5% 5% 5% 5% 5% 3% 3% 2% 2% 30W 30W 35W 40W 40W 40W 40W 40W 40W 40W MTDA40A-S02 5 ~ 5.99 VDC MTDA40A-S03 6.5 ~ 8 VDC MTDA40A-S04 8 ~ 11 VDC MTDA40A-S05 11 ~ 13 VDC MTDA40A-S06 13 ~ 16 VDC MTDA40A-S07 16 ~ 21 VDC MTDA40A-S08 21 ~ 27 VDC MTDA40A-S09 27 ~ 33 VDC MTDA40A-S10 33 ~ 40 VDC MTDA40A-S11 40 ~ 48 VDC Total Regulation is conditioned by below configuration (S02~S05: AWG16/4FT output cable) (S06~S08: AWG18/4FT output cable) (S09~S11: AWG18/6FT output cable) Electrical Characteristics Parameter Input Voltage Input Frequency Output Power Range Input Current (Low Line) Input Current (High Line) Low Line Inrush Current High Line Inrush Current Efficiency Line Regulation Load Regulation Over Voltage Protection Over Current Protection Transient Response Hold-Up Time Start Up Time Ripple & Noise (Peak to Peak) Safety Ground Leakage Current Temperature Coefficient No-load Power Consumption Test Conditions Universal Input Voltage Operating Voltage Vin=100 to 240VAC Io=Full load, Vin=115VAC Io=Full load, Vin=230VAC Io=Full load, 25°C, Cool start, Vin=115VAC Io=Full load, 25°C, Cool start, Vin=230VAC Io=Full Load, Vin=230VAC Io=Full Load Vin=230VAC Min. Typ. 100 90 47 0 83 40 80 87 0.5 3 Nil 110 Io=Full Load to Half Load, Vin=100VAC Io=Full Load, Vin=230VAC Io=Full Load, Vin=100VAC Full Load, Vin=90VAC Io=Full Load, Vin=240VAC All output No load, Vin=240VAC Max. Unit 240 264 63 40 0.8 0.52 45 90 90 1 7 VAC VAC Hz W A A A A % % % % % mS mS S % mA %/°C W 150 4 10 2 0.5 0.5 -0.04 0.2 3 1 0.75 0.04 0.3 Conditions Parameter Test Conditions Operating Temperature Storage Temperature Operating Humidity Storage Humidity Operating Temperature at 25°C, Calculated per MIL-HDBK-217F Min. Typ. Max. Unit 0 -40 0 0 0.1M 40 70 85 95 75 °C °C % % Hrs Min. Unit 4242 2121 50 B B VDC VDC MΩ CLASS CLASS Approvals and Compliance Parameter Test Conditions Dielectric Withstanding Voltage for Primary to secondary Dielectric Withstanding Voltage for Primary to Ground Isolation Resistance EMI requirements for CISPR-22 EMI requirements for FCC PART-15 Primary to secondary Primary to ground Test Voltage=500VDC Vin=220VAC Vin=110VAC Mechanical and PIN out Note: 1. Dimensions are shown in mm. 2. Weight: 265~280g approx. 3. Optional output connector.