! # ! ! $!! "!"! Independent Registers for A and B Buses Multiplexed Real-Time and Stored Data Transfers Choice of True and Inverting Data Paths 3-State Outputs 300 mil Slim Dual-in-Line Package Outputs Source/Sink 24 mA ′ACT652 Has TTL Compatible Inputs 1 REAL TIME TRANSFER B-BUS TO A-BUS A-BUS A-BUS REG OCTAL TRANSCEIVER/ REGISTER WITH 3-STATE OUTPUTS (NON-INVERTING) 24 REAL TIME TRANSFER A-BUS TO B-BUS REG $ #! The MC74AC/ACT652 consists of registered bus transceiver circuits, with outputs, D-type flip-flops and control circuitry providing multiplexed transmission of data directly from the input bus or from the internal storage registers. Data on the A or B bus will be loaded into the respective registers on the LOW-to-HIGH transition of the appropriate clock pin (CAB or CBA). The four fundamental data handling functions available are illustrated in Figures 1 to 4. • • • • • • • REG N SUFFIX CASE 724-03 PLASTIC PACKAGE REG 24 1 B-BUS B-BUS Figure 1 Figure 2 STORAGE FROM BUS TO REGISTER TRANSFER FROM REGISTER TO BUS A-BUS A-BUS REG REG REG DW SUFFIX CASE 751E-04 SOIC PACKAGE A0 – A7 REG B-BUS B-BUS Figure 3 Figure 4 PIN NAMES B0 – B7 CAB, CBA SAB, SBA GAB, GBA Data Register A Inputs Data Register A Outputs Data Register B Inputs Data Register B Outputs Clock Pulse Inputs Transmit/Receive Inputs Output Enable Inputs MAXIMUM RATINGS* Symbol Parameter Value Unit –0.5 to +7.0 V VCC DC Supply Voltage (Referenced to GND) Vin DC Input Voltage (Referenced to GND) –0.5 to VCC + 0.5 V Vout DC Output Voltage (Referenced to GND) –0.5 to VCC + 0.5 V Iin DC Input Current, per Pin ± 20 mA Iout DC Output Sink/Source Current, per Pin ± 50 mA ICC DC VCC or GND Current per Output Pin ± 50 mA Tstg Storage Temperature –65 to +150 °C * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. FACT DATA 5-1 MC74AC652 MC74ACT652 Pinout: 24-Lead Plastic Package (Top View) VCC CBA SBA GBA B0 B1 B2 B3 B4 B5 B6 B7 24 23 22 21 20 19 18 17 16 15 14 13 1 2 3 4 5 6 7 8 9 10 11 12 CAB SAB GAB A0 A1 A2 A3 A4 A5 A6 A7 GND LOGIC SYMBOL CAB SAB GAB CBA SBA GBA B0 B1 B2 B3 B4 B5 B6 B7 A0 A1 A2 A3 A4 A5 A6 A7 LOGIC DIAGRAM GBA GAB CBA SBA CAB SAB 1 OF 8 CHANNELS D0 C0 B0 A0 D0 C0 TO 7 OTHER CHANNELS Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. FACT DATA 5-2 MC74AC652 MC74ACT652 FUNCTION TABLE Inputs Data I/O* Operation or Function GAB GBA CAB CBA SAB SBA A0 – A7 B0 – B7 L L H H H or L ⇑ H or L ⇑ X X X X Input Input X H H H ⇑ ⇑ H or L ⇑ X X** X X Input Input Unspecified* Output Store A, Hold B Store A in Both Registers L L X L H or L ⇑ ⇑ ⇑ X X X X** Unspecified* Output Input Input Hold A, Store B Store B in Both Registers L L L L X X X H or L X X L H Output Input Real-Time B Data to A Bus Stored B Data to A Bus H H H H X H or L X X L H X X Input Output Real-Time A Data to B Bus Stored A Data to B Bus H L H or L H or L H H Output Output Stored A Data to B Bus and Stored B Data to A Bus Isolation Store A and B Data * The data output functions may be enabled or disabled by various signals at the GBA and GAB inputs. Data input functions are always enabled; i.e., data at the bus pins will be stored on every LOW-to-HIGH transition of the appropriate clock inputs. ** Select control = L: clocks can occur simultaneously. H = HIGH Voltage Level; L = LOW Voltage Level; X = Immaterial; ⇑ = LOW-to-HIGH Transition RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage Vin, Vout DC Input Voltage, Output Voltage (Ref. to GND) tr, tf Input Rise and Fall Time (Note 1) ′AC Devices except Schmitt Inputs tr, tf Input Rise and Fall Time (Note 2) ′ACT Devices except Schmitt Inputs TJ Junction Temperature (PDIP) TA Operating Ambient Temperature Range IOH IOL Min Typ Min ′AC 2.0 5.0 6.0 ′ACT 4.5 5.0 5.5 0 VCC VCC @ 3.0 V 150 VCC @ 4.5 V 40 VCC @ 5.5 V 25 VCC @ 4.5 V 10 VCC @ 5.5 V 8.0 Unit V V ns/V ns/V 140 °C 85 °C Output Current — HIGH –24 mA Output Current — LOW 24 mA –40 1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. FACT DATA 5-3 25 MC74AC652 MC74ACT652 DC CHARACTERISTICS Symbol Parameter VCC (V) 74AC 74AC TA = +25°C TA = –40°C to +85°C Typ VIH VIL VOH Guaranteed Limits 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 V VOUT = 0.1 V or VCC – 0.1 V Maximum Low Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 V VOUT = 0.1 V or VCC – 0.1 V Minimum High Level Output Voltage 3.0 4.5 5.5 2.99 4.49 5.49 2.9 4.4 5.4 2.9 4.4 5.4 V 2.56 3.86 4.86 2.46 3.76 4.76 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 5.5 0.36 0.36 0.36 0.44 0.44 0.44 5.5 ±0.1 5.5 ±0.6 Minimum Low Level Output Voltage IIN Maximum Input Leakage Current IOZT Maximum 3-State 3.0 4.5 5.5 0.002 0.001 0.001 IOUT = – 50 µA V IOHD ICC †Minimum Dynamic Output Current Maximum Quiescent Supply Current *VIN = VIL or VIH – 12 mA IOH – 24 mA – 24 mA IOUT = 50 µA V V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA ±1.0 µA VI = VCC, GND ±6.0 µA VI (OE) = VIL, VIH VI = VCC, GND VO= VCC, GND 5.5 75 mA VOLD = 1.65 V Max 5.5 –75 mA VOHD = 3.85 V Min 80 µA VIN = VCC or GND Current IOLD Conditions Minimum High Level Input Voltage 3.0 4.5 5.5 VOL Unit 5.5 8.0 * All outputs loaded; thresholds on input associated with output under test. † Maximum test duration 2.0 ms, one input loaded at a time. Note: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V. FACT DATA 5-4 MC74AC652 MC74ACT652 AC CHARACTERISTICS Symbol VCC* (V) Parameter 74AC 74AC TA = +25°C CL = 50 pF TA = –40°C to +85°C CL = 50 pF Min Max Min Max Unit tPLH Propagation Delay CPBA or CPAB to An or Bn 3.0 5.0 4.0 2.5 17.0 12.0 3.0 2.0 19.0 14.0 ns tPHL Propagation Delay CPBA or CPAB to An or Bn 3.0 5.0 3.0 2.0 14.5 10.5 2.5 1.5 16.5 12.0 ns tPLH Propagation Delay A or B to Bn or An 3.0 5.0 3.0 2.0 14.0 9.5 2.5 1.5 16.0 11.0 ns tPHL Propagation Delay A or B to Bn or An 3.0 5.0 2.5 1.5 13.0 9.0 2.0 1.0 15.0 10.5 ns tPLH Propagation Delay SBA or SAB to An or Bn 3.0 5.0 3.0 2.5 14.0 10.0 2.5 2.0 16.0 11.5 ns tPHL Propagation Delay SBA or SAB to An or Bn 3.0 5.0 2.5 2.0 13.5 10.0 2.0 1.5 15.5 11.5 ns tPZH Output Enable Time OEBA to An 3.0 5.0 2.5 1.5 12.0 9.0 2.0 1.0 13.5 10.0 ns tPZL Output Enable Time OEBA to An 3.0 5.0 2.5 1.5 12.0 9.0 2.0 1.0 14.0 10.5 ns tPHZ Output Disable Time OEBA to An 3.0 5.0 3.0 2.0 13.0 11.0 2.5 1.5 14.0 12.0 ns tPLZ Output Disable Time OEBA to An 3.0 5.0 2.5 2.0 12.5 10.5 2.0 1.5 14.0 12.0 ns * Voltage Range 3.3 V is 3.3 V ±0.3 V. Voltage Range 5.0 V is 5.0 V ±0.5 V. FACT DATA 5-5 MC74AC652 MC74ACT652 DC CHARACTERISTICS Symbol Parameter VCC (V) 74ACT 74ACT TA = +25°C TA = –40°C to +85°C Typ Guaranteed Limits Unit Conditions VIH Minimum High Level Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 V VOUT = 0.1 V or VCC – 0.1 V VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT = 0.1 V or VCC – 0.1 V VOH Minimum High Level Output Voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 V 3.86 4.86 3.76 4.76 0.1 0.1 0.1 0.1 4.5 5.5 0.36 0.36 0.44 0.44 V *VIN = VIL or VIH – 24 mA IOH – 24 mA ±0.1 ±1.0 µA VI = VCC, GND 1.5 mA VI = VCC – 2.1 V ±6.0 µA VI (OE) = VIL, VIH VI = VCC, GND VO = VCC, GND 5.5 75 mA VOLD = 1.65 V Max 5.5 –75 mA VOHD = 3.85 V Min 80 µA VIN = VCC or GND 4.5 5.5 VOL Minimum Low Level Output Voltage 4.5 5.5 IIN Maximum Input Leakage Current 5.5 ∆ICCT Additional Max. ICC/Input 5.5 IOZT Maximum 3-State 5.5 0.001 0.001 0.6 ±0.6 V V Current IOLD IOHD ICC †Minimum Dynamic Output Current Maximum Quiescent Supply Current 5.5 8.0 * All outputs loaded; thresholds on input associated with output under test. † Maximum test duration 2.0 ms, one input loaded at a time. FACT DATA 5-6 IOUT = – 50 µA *VIN = VIL or VIH – 24 mA IOH – 24 mA IOUT = – 50 µA MC74AC652 MC74ACT652 AC CHARACTERISTICS Symbol VCC* (V) Parameter 74ACT 74ACT TA = +25°C CL = 50 pF TA = –40°C to +85°C CL = 50 pF Min Max Min Max Unit tPLH Propagation Delay CPBA or CPAB to An or Bn 5.0 4.0 14.5 3.5 16.5 ns tPHL Propagation Delay CPBA or CPAB to An or Bn 5.0 3.5 14.5 3.0 16.5 ns tPLH Propagation Delay A or B to Bn or An 5.0 2.5 11.5 2.0 13.0 ns tPHL Propagation Delay A or B to Bn or An 5.0 2.5 11.5 2.0 13.0 ns tPLH Propagation Delay SBA or SAB to An or Bn 5.0 2.5 12.0 2.0 13.5 ns tPHL Propagation Delay SBA or SAB to An or Bn 5.0 3.0 12.0 2.5 13.5 ns tPZH Output Enable Time OEBA to An 5.0 2.0 11.5 1.5 13.0 ns tPZL Output Enable Time OEBA to An 5.0 2.5 11.5 2.0 13.0 ns tPHZ Output Disable Time OEBA to An 5.0 3.0 13.0 2.5 14.0 ns tPLZ Output Disable Time OEBA to An 5.0 2.5 12.5 2.0 14.0 ns tPZH Output Enable time OEAB to Bn 5.0 2.5 12.0 2.0 13.5 ns tPZL Output Enable Time OEAB to Bn 5.0 2.5 12.0 2.0 13.5 ns tPHZ Output Enable Time OEAB to Bn 5.0 3.5 13.5 3.0 14.5 ns tPLZ Output Enable Time OEAB to Bn 5.0 3.0 13.5 2.5 15.0 ns ts Setup Time, HIGH or LOW An or Bn to CPBA or CPAB 5.0 7.0 8.0 ns th Hold Time, HIGH or LOW An or Bn to CPBA or CPAB 5.0 2.5 2.5 ns tw CPAB, CPBA Pulse Width HIGH or LOW 5.0 6.0 7.0 ns * Voltage Range 3.3 V is 3.3 V ±0.3 V. Voltage Range 5.0 V is 5.0 V ±0.5 V. CAPACITANCE Symbol Parameter 74ACT Typ Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CI/O Input/Output Capacitance 15 pF VCC = 5.0 V CPD Power Dissipation Capacitance 60.0 pF VCC = 5.0 V FACT DATA 5-7 MC74AC652 MC74ACT652 OUTLINE DIMENSIONS N SUFFIX PLASTIC DIP PACKAGE CASE 724–03 ISSUE D –A– 24 13 1 12 NOTES: 1. CHAMFERED CONTOUR OPTIONAL. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 4. CONTROLLING DIMENSION: INCH. –B– L C –T– NOTE 1 K SEATING PLANE N E G M J F D 24 PL 0.25 (0.010) 24 PL 0.25 (0.010) T A M M T B M 24 12X P 0.010 (0.25) 1 M B M 12 D J 0.010 (0.25) M T A S B S F R C –T– M 22X MILLIMETERS MIN MAX 31.25 32.13 6.35 6.85 3.69 4.44 0.38 0.51 1.27 BSC 1.02 1.52 2.54 BSC 0.18 0.30 2.80 3.55 7.62 BSC 0_ 15_ 0.51 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. 13 –B– SEATING PLANE INCHES MIN MAX 1.230 1.265 0.250 0.270 0.145 0.175 0.015 0.020 0.050 BSC 0.040 0.060 0.100 BSC 0.007 0.012 0.110 0.140 0.300 BSC 0_ 15_ 0.020 0.040 DW SUFFIX PLASTIC SOIC PACKAGE CASE 751E–04 ISSUE E –A– 24X M DIM A B C D E F G J K L M N K G X 45 _ DIM A B C D F G J K M P R MILLIMETERS MIN MAX 15.25 15.54 7.40 7.60 2.35 2.65 0.35 0.49 0.41 0.90 1.27 BSC 0.23 0.32 0.13 0.29 0_ 8_ 10.05 10.55 0.25 0.75 INCHES MIN MAX 0.601 0.612 0.292 0.299 0.093 0.104 0.014 0.019 0.016 0.035 0.050 BSC 0.009 0.013 0.005 0.011 0_ 8_ 0.395 0.415 0.010 0.029 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] –TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ FACT DATA 5-8 *MC74AC652/D* MC74AC652/D