NSC DS90UR124IVS 5-43 mhz dc-balanced 24-bit fpd-link ii serializer and deserializer chipset Datasheet

September 4, 2009
5-43 MHz DC-Balanced 24-Bit FPD-Link II Serializer and
Deserializer Chipset
General Description
The DS90UR241/124 Chipset translates a 24-bit parallel bus
into a fully transparent data/control FPD-Link II LVDS serial
stream with embedded clock information. This chipset is ideally suited for driving graphical data to displays requiring 18bit color depth - RGB666 + HS, VS, DE + 3 additional general
purpose data channels. This single serial stream simplifies
transferring a 24-bit bus over PCB traces and cable by eliminating the skew problems between parallel data and clock
paths. It saves system cost by narrowing data paths that in
turn reduce PCB layers, cable width, and connector size and
pins.
The DS90UR241/124 incorporates FPD-Link II LVDS signaling on the high-speed I/O. FPD-Link II LVDS provides a low
power and low noise environment for reliably transferring data
over a serial transmission path. By optimizing the Serializer
output edge rate for the operating frequency range EMI is further reduced.
In addition, the device features pre-emphasis to boost signals
over longer distances using lossy cables. Internal DC balanced encoding/decoding is used to support AC-Coupled
interconnects. Using National Semiconductor’s proprietary
random lock, the Serializer’s parallel data are randomized to
the Deserializer without the need of REFCLK.
Features
■ Supports displays with 18-bit color depth
■ 5MHz to 43MHz pixel clock
■ Automotive grade product AEC-Q100 grade 2 qualified
■ 24:1 interface compression
■ Embedded clock with DC Balancing supports AC-coupled
data transmission
■ Capable to drive up to 10 meters shielded twisted-pair
■
■
■
■
■
■
■
■
■
■
cable
No reference clock required (deserializer)
Meets ISO 10605 ESD - Greater than 8 kV HBM ESD
structure
Hot plug support
EMI Reduction - Serializer accepts spread spectrum input;
data randomization and shuffling on serial link;
Deserializer provides Adjustable PTO (progressive turnon) LVCMOS outputs
@Speed BIST (built-in self test) to validate LVDS
transmission path
Individual power-down controls for both Transmitter and
Receiver
Power supply range 3.3V ± 10%
48-pin TQFP package for Transmitter and 64-pin TQFP
package for Receiver
Temperature range -40°C to +105°C
Backward compatible mode with DS90C241/DS90C124
Applications
■
■
■
■
Automotive Central Information Display
Automotive Instrument Cluster Display
Automotive Heads-Up Display
Remote Camera-based Driver Assistance Systems
Applications Diagram
20194527
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 2009 National Semiconductor Corporation
201945
www.national.com
DS90UR241Q/DS90UR124Q 5-43 MHz DC-Balanced 24-Bit FPD-Link II Serializer and Deserializer
Chipset
DS90UR241Q
DS90UR124Q
DS90UR241Q/DS90UR124Q
Block Diagram
20194501
Ordering Information
NSID
Package Type
DS90UR241QVS
48-Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch
VBC48A
DS90UR241QVSX
48-Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch
VBC48A
DS90UR241IVS
48-Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch
VBC48A
DS90UR241IVSX
48-Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch
VBC48A
DS90UR124QVS
64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch
VEC64A
DS90UR124QVSX
64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch
VEC64A
DS90UR124IVS
64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch
VEC64A
DS90UR124IVSX
64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch
VEC64A
www.national.com
Package ID
2
Quantity
1000
1000
1000
1000
Supply Voltage (VDD)
−0.3V to +4V
LVCMOS Input Voltage
−0.3V to (VDD +0.3V)
LVCMOS Output Voltage
−0.3V to (VDD +0.3V)
LVDS Receiver Input Voltage
−0.3V to +3.9V
LVDS Driver Output Voltage
−0.3V to +3.9V
LVDS Output Short Circuit Duration
10 ms
Junction Temperature
+150°C
Storage Temperature
−65°C to +150°C
Lead Temperature
(Soldering, 4 seconds)
+260°C
Maximum Package Power Dissipation Capacity
(Note 2)
Package De-rating:
1/θJA °C/W above +25°C
21.0°C/W
42.8 (4L*); 67.2 (2L*)°C/W
θJC
14.6°C/W
±10 kV
Air Discharge (DOUT+, DOUT−)
±30 kV
Contact Discharge (RIN+, RIN−)
±10 kV
Air Discharge (RIN+, RIN−)
±30 kV
Supply Voltage (VDD)
Operating Free Air
Temperature (TA)
Clock Rate
Supply Noise
45.8 (4L*); 75.4 (2L*) °C/W
θJA
Contact Discharge (DOUT+, DOUT−)
Recommended Operating
Conditions
DS90UR241 − 48L TQFP
θJC
DS90UR124 − 64L TQFP
RD = 2 kΩ, CS = 330 pF
Min
3.0
Nom
3.3
Max
3.6
Units
V
−40
5
+25
+105
43
±100
°C
MHz
mVP-P
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Pin/Freq.
Min
Typ
Max
Units
Tx: DIN[0:23], TCLK,
2.0
TPWDNB, DEN, TRFB, GND
RAOFF, VODSEL,
RES0.
Rx: RPWDNB, RRFB,
−0.8
REN, PTOSEL,
BISTEN, BISTM,
SLEW, RES0.
VDD
V
0.8
V
−1.5
V
LVCMOS DC SPECIFICATIONS
VIH
High Level Input Voltage
VIL
Low Level Input Voltage
VCL
Input Clamp Voltage
IIN
Input Current
ICL = −18 mA
VIN = 0V or 3.6V
VOH
High Level Output Voltage
IOH = −2 mA, SLEW = L
IOH = −4 mA, SLEW = H
VOL
Low Level Output Voltage
IOL = +2 mA, SLEW = L
IOL = +4 mA, SLEW = H
IOS
Output Short Circuit Current
VOUT = 0V
IOZ
TRI-STATE® Output Current
RPWDNB, REN = 0V,
VOUT = 0V or VDD
Tx: DIN[0:23], TCLK,
TPWDNB, DEN, TRFB,
RAOFF, RES0.
−10
Rx: RRFB, REN,
PTOSEL, BISTEN,
BISTM, SLEW, RES0.
±2
+10
µA
Rx: RPWDNB
−20
±5
+20
µA
Rx: ROUT[0:23], RCLK,
LOCK, PASS.
2.3
3.0
VDD
V
GND 0.33
0.5
V
Rx: ROUT[0:23], RCLK,
LOCK, PASS.
3
−40
−70
−110
mA
−30
±0.4
+30
µA
www.national.com
DS90UR241Q/DS90UR124Q
ESD Rating (ISO10605)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
θJA
≥±8 kV
ESD Rating (HBM)
Absolute Maximum Ratings (Note 1)
DS90UR241Q/DS90UR124Q
Symbol
Parameter
Conditions
Pin/Freq.
Min
Typ
Max
Units
+50
mV
LVDS DC SPECIFICATIONS
VTH
Differential Threshold High
Voltage
VTL
Differential Threshold Low
Voltage
IIN
Input Current
VOD
Output Differential Voltage
(DOUT+)–(DOUT−)
VCM = +1.8V
Rx: RIN+, RIN−
−50
VIN = +2.4V, VDD = 3.6V
VIN = 0V, VDD = 3.6V
ΔVOD
VOS
ΔVOS
IOS
IOZ
mV
±100
±250
µA
µA
±100
±250
RL = 100Ω, w/o preemphasis (Figure 10)
VODSEL = L Tx: DOUT+, DOUT−
380
500
630
VODSEL = H
500
900
1100
Output Differential Voltage
Unbalance
RL = 100Ω,
w/o pre-emphasis
VODSEL = L
1
50
mV
Offset Voltage
RL = 100Ω,
w/o pre-emphasis
VODSEL = L
1.50
V
RL = 100Ω,
w/o pre-emphasis
VODSEL = L
50
mV
DOUT = 0V, DIN = H,
TPWDNB = 2.4V
VODSEL = L
−2.0 −5.0
−8.0
VODSEL = H
−4.5 −7.9
−14.0
Offset Voltage Unbalance
Output Short Circuit Current
TRI-STATE Output Current
VODSEL = H
1.00 1.25
VODSEL = H
3
VODSEL = H
mV
mA
TPWDNB = 0V,
DOUT = 0V OR VDD
−15
±1
+15
µA
TPWDNB = 2.4V, DEN = 0V
DOUT = 0V OR VDD
−15
±1
+15
µA
TPWDNB = 2.4V, DEN = 2.4V,
DOUT = 0V OR VDD
NO LOCK (NO TCLK)
−15
±1
+15
µA
60
85
mA
65
90
mA
66
90
mA
45
µA
SER/DES SUPPLY CURRENT (DVDD*, PVDD* AND AVDD* PINS) *DIGITAL, PLL, AND ANALOG VDDS
IDDT
Serializer
Total Supply Current
(includes load current)
RL = 100Ω, PRE = OFF,
RAOFF = H, VODSEL = L
RL = 100Ω, PRE = 12 kΩ,
RAOFF = H, VODSEL = L
RL = 100Ω, PRE = OFF,
RAOFF = H, VODSEL = H
f = 43 MHz,
CHECKER BOARD
Pattern (Figure 1)
f = 43 MHz,
RANDOM pattern
IDDTZ
Serializer
Supply Current Power-down
TPWDNB = 0V
(All other LVCMOS Inputs = 0V)
IDDR
Deserializer
Total Supply Current
(includes load current)
CL = 4 pF,
SLEW = H
f = 43 MHz,
CHECKER BOARD
Pattern LVCMOS
Output (Figure 2)
85
105
mA
CL = 4 pF,
SLEW = H
f = 43 MHz,
RANDOM pattern
LVCMOS Output
80
100
mA
50
µA
IDDRZ
Deserializer
Supply Current Power-down
www.national.com
RPWDNB = 0V
(All other LVCMOS Inputs = 0V,
RIN+/RIN- = 0V)
4
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
tTCP
Transmit Clock Period
(Figure 5)
tTCIH
Transmit Clock High Time
tTCIL
Transmit Clock Low Time
tCLKT
TCLK Input Transition Time
Figure 4, ((Note 9))
tJIT
TCLK Input Jitter
(Note 10)
Min
Typ
Max
Units
23.25
T
200
ns
0.3T
0.5T
0.7T
ns
0.3T
0.5T
0.7T
ns
2.5
ns
±100
ps
Serializer Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
tLHLT
LVDS Low-to-High Transition Time RL = 100Ω, VODSEL = L,
LVDS High-to-Low Transition Time CL = 10 pF to GND, (Figure 3)
tDIS
DIN (0:23) Setup to TCLK
tDIH
DIN (0:23) Hold from TCLK
tHZD
DOUT ± HIGH to TRI-STATE Delay
tLZD
DOUT ± LOW to TRI-STATE Delay
tZHD
DOUT ± TRI-STATE to HIGH Delay
tZLD
DOUT ± TRI-STATE to LOW Delay
tPLD
Serializer PLL Lock Time
RL = 100Ω
tSD
Serializer Delay
RL = 100Ω, PRE = OFF,
RAOFF = L, TRFB = H,
(Figure 8)
RL = 100Ω, PRE = OFF,
RAOFF = L, TRFB = L,
(Figure 8)
tLLHT
Min
RL = 100Ω, CL = 10 pF to GND,
(Note 9), (Figure 5)
TxOUT_E_O TxOUT_Eye_Opening.
TxOUT_E_O centered on (tBIT/)2
Typ
Max
Units
245
550
ps
264
550
ps
4
ns
4
RL = 100Ω,
CL = 10 pF to GND,
(Note 6), (Figure 6)
ns
10
15
ns
10
15
ns
75
150
ns
75
150
ns
10
ms
3.5T+2
3.5T+10
ns
3.5T+2
3.5T+10
ns
5 MHz–43 MHz,
RL = 100Ω, CL = 10 pF to GND,
RANDOM pattern
(Note 10, Note 11), (Note 14)
(Figure 9)
0.76
0.84
UI
Deserializer Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Pin/Freq.
tRCP
Receiver out Clock Period
tRCP = tTCP,
PTOSEL = H
RCLK
(Figure 15)
tRDC
RCLK Duty Cycle
PTOSEL = H,
SLEW = L
tCLH
LVCMOS Low-to-High
Transition Time
ROUT [0:23],
RCLK, LOCK
tCHL
LVCMOS High-to-Low
Transition Time
CL = 4 pF
(lumped load),
SLEW = H
(Note 9)
tCLH
LVCMOS Low-to-High
Transition Time
ROUT [0:23],
RCLK, LOCK
tCHL
LVCMOS High-to-Low
Transition Time
CL = 4 pF
(lumped load),
SLEW = L
(Note 9)
5
Min
Typ
Max
Units
23.25
T
200
ns
45
50
55
%
1.5
2.5
ns
1.5
2.5
ns
2.0
3.5
ns
2.0
3.5
ns
www.national.com
DS90UR241Q/DS90UR124Q
Serializer Input Timing Requirements for TCLK
DS90UR241Q/DS90UR124Q
Symbol
tROS
Parameter
Conditions
PTOSEL = L,
SLEW = H,
ROUT (0:7) Hold Data to RCLK (Figure 16)
(Group 1)
ROUT[0:7]
tROS
ROUT (8:15) Setup Data to
RCLK (Group 2)
ROUT [8:15],
LOCK
tROH
ROUT (8:15) Hold Data to
RCLK (Group 2)
tROS
ROUT (16:23) Setup Data to
RCLK (Group 3)
tROH
ROUT (16:23) Setup Data to
RCLK (Group 3)
tROS
ROUT (0:7) Setup Data to
RCLK (Group 1)
tROH
ROUT (0:7) Setup Data to
RCLK (Group 1)
Pin/Freq.
PTOSEL = L,
SLEW = H,
(Figure 16)
ROUT [16:23]
PTOSEL = H,
SLEW = H,
ROUT (0:7) Hold Data to RCLK (Figure 15)
(Group 1)
ROUT[0:7]
tROS
ROUT (8:15) Setup Data to
RCLK (Group 2)
ROUT [8:15],
LOCK
tROH
ROUT (8:15) Hold Data to
RCLK (Group 2)
tROS
ROUT (16:23) Setup Data to
RCLK (Group 3)
tROH
ROUT (16:23) Setup Data to
RCLK (Group 3)
tHZR
HIGH to TRI-STATE Delay
tLZR
LOW to TRI-STATE Delay
tZHR
TRI-STATE to HIGH Delay
tZLR
TRI-STATE to LOW Delay
tDD
Deserializer Delay
PTOSEL = H,
(Figure 12)
RCLK
tDSR
Deserializer PLL Lock Time
from Powerdown
(Note 7, Note 9)
RxIN_TOL-L
Receiver INput TOLerance
Left
(Note 8, Note 9),
(Note 11)
(Figure 17)
tROH
RxIN_TOL-R Receiver INput TOLerance
Right
ROUT [16:23]
PTOSEL = H,
(Figure 14)
Min
Typ
(0.35)*
tRCP
(0.5*tRCP)–3 UI
ns
(0.35)*
tRCP
(0.5*tRCP)–3 UI
ns
(0.35)*
tRCP
(0.5*tRCP)–3 UI
ns
(0.35)*
tRCP
(0.5*tRCP)–3 UI
ns
(0.35)*
tRCP
(0.5*tRCP)–3 UI
ns
(0.35)*
tRCP
(0.5*tRCP)–3 UI
ns
(0.35)*
tRCP
(0.5*tRCP)–2 UI
ns
(0.35)*
tRCP
(0.5*tRCP)+2 UI
ns
(0.35)*
tRCP
(0.5*tRCP)−1 UI
ns
(0.35)*
tRCP
(0.5*tRCP)+1 UI
ns
(0.35)*
tRCP
(0.5*tRCP)+1 UI
ns
(0.35)*
tRCP
(0.5*tRCP)–1 UI
ns
ROUT [0:23],
RCLK, LOCK
Max
Units
3
10
ns
3
10
ns
3
10
ns
3
10
ns
[5+(5/56)]T+3.7
[5+(5/56)]T
+8
ns
5 MHz
128k*T
ms
43 MHz
128k*T
ms
0.25
UI
0.25
UI
5 MHz–43 MHz
(Note 8),(Note 9, 5 MHz–43 MHz
Note 11)
(Figure 17)
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability
and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in
the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the
device should not be operated beyond such conditions.
Note 2: 4L =4 layer PCB per JEDEC specification, 2L = 2 layer PCB per JEDEC specification.
Note 3: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified
or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed.
Note 4: Typical values represent most likely parametric norms at VDD = 3.3V, Ta = +25 degC, and at the Recommended Operation Conditions at the time of
product characterization and are not guaranteed.
Note 5: Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground except VOD, ΔVOD,
VTH and VTL which are differential voltages.
Note 6: When the Serializer output is at TRI-STATE the Deserializer will lose PLL lock. Resynchronization MUST occur before data transfer.
Note 7: tDSR is the time required by the Deserializer to obtain lock when exiting powerdown mode.
Note 8: RxIN_TOL is a measure of how much phase noise (jitter) the Deserializer can tolerate in the incoming data stream before bit errors occur. It is a
measurement in reference with the ideal bit position, please see National’s AN-1217 for detail.
Note 9: Specification is guaranteed by characterization and is not tested in production.
Note 10: tJIT (@BER of 10e-9) specifies the allowable jitter on TCLK. tJIT not included in TxOUT_E_O parameter.
www.national.com
6
DS90UR241Q/DS90UR124Q
Note 11: UI – Unit Interval, equivalent to one ideal serialized data bit width. The UI scales with frequency.
Note 12: Figures 1, 2 Figures 8, 12, 14show a falling edge data strobe (TCLK IN/RCLK OUT).
Note 13: Figures 5, 15, 16 show a rising edge data strobe (TCLK IN/RCLK OUT).
Note 14: TxOUT_E_O is affected by pre-emphasis value.
AC Timing Diagrams and Test Circuits
20194502
FIGURE 1. Serializer Input Checkerboard Pattern
20194503
FIGURE 2. Deserializer Output Checkerboard Pattern
20194504
FIGURE 3. Serializer LVDS Output Load and Transition Times
7
www.national.com
DS90UR241Q/DS90UR124Q
20194506
FIGURE 4. Serializer Input Clock Transition Times
20194507
FIGURE 5. Serializer Setup/Hold Times
20194508
FIGURE 6. Serializer TRI-STATE Test Circuit and Delay
www.national.com
8
DS90UR241Q/DS90UR124Q
20194509
FIGURE 7. Serializer PLL Lock Time, and TPWDNB TRI-STATE Delays
20194510
FIGURE 8. Serializer Delay
20194515
FIGURE 9. Transmitter Output Eye Opening (TxOUT_E_O)
9
www.national.com
DS90UR241Q/DS90UR124Q
20194517
VOD = (DOUT+) – (DOUT−)
Differential output signal is shown as (DOUT+) – (DOUT−), device in Data Transfer mode.
FIGURE 10. Serializer VOD Diagram
20194505
FIGURE 11. Deserializer LVCMOS Output Load and Transition Times
20194511
FIGURE 12. Deserializer Delay
www.national.com
10
DS90UR241Q/DS90UR124Q
20194513
FIGURE 13. Deserializer TRI-STATE Test Circuit and Timing
20194514
FIGURE 14. Deserializer PLL Lock Times and RPWDNB TRI-STATE Delay
11
www.national.com
DS90UR241Q/DS90UR124Q
20194512
FIGURE 15. Deserializer Setup and Hold Times and PTO, PTOSEL = H
20194521
Group 1 will be latched internally by sequence of (early 2UI, late 1UI, early 1UI, late 2UI)
Group 2 will be latched internally by sequence of (late 1UI, early 1UI, late 2UI, early 2UI)
Group 3 will be latched internally by sequence of (early 1UI, late 2UI, early 2UI, late 1UI)
FIGURE 16. Deserializer Setup and Hold Times and PTO Spread, PTOSEL = L
www.national.com
12
DS90UR241Q/DS90UR124Q
20194516
RxIN_TOL_L is the ideal noise margin on the left of the figure, with respect to ideal.
RxIN_TOL_R is the ideal noise margin on the right of the figure, with respect to ideal.
FIGURE 17. Receiver Input Tolerance (RxIN_TOL) and Sampling Window
DS90UR241 Pin Diagram
Serializer - DS90UR241
20194519
TOP VIEW
DS90UR241 Serializer Pin Descriptions
Pin #
Pin Name
I/O/PWR
Description
LVCMOS PARALLEL INTERFACE PINS
4-1,
DIN[23:0]
48-44,
41-32,
29-25
LVCMOS_I
Transmitter Parallel Interface Data Input Pins. Tie LOW if unused, do not float.
10
LVCMOS_I
Transmitter Parallel Interface Clock Input Pin. Strobe edge set by TRFB configuration pin.
TCLK
13
www.national.com
DS90UR241Q/DS90UR124Q
Pin #
Pin Name
I/O/PWR
Description
CONTROL AND CONFIGURATION PINS
9
TPWDNB
LVCMOS_I
Transmitter Power Down Bar
TPWDNB = H; Transmitter is Enabled and ON
TPWDNB = L; Transmitter is in power down mode (Sleep), LVDS Driver DOUT (+/-) Outputs are
in TRI-STATE stand-by mode, PLL is shutdown to minimize power consumption.
24
VODSEL
LVCMOS_I
VOD Level Select
VODSEL = L; LVDS Driver Output is ±500 mV (RL = 100Ω)
VODSEL = H; LVDS Driver Output is ±900 mV (RL = 100Ω)
For normal applications, set this pin LOW. For long cable applications where a larger VOD is
required, set this pin HIGH.
18
DEN
LVCMOS_I
Transmitter Data Enable
DEN = H; LVDS Driver Outputs are Enabled (ON).
DEN = L; LVDS Driver Outputs are Disabled (OFF), Transmitter LVDS Driver DOUT (+/-) Outputs
are in TRI-STATE, PLL still operational and locked to TCLK.
23
PRE
LVCMOS_I
Pre-emphasis Level Select
PRE = NC (No Connect); Pre-emphasis is Disabled (OFF).
Pre-emphasis is active when input is tied to VSS through external resistor RPRE. Resistor value
determines pre-emphasis level. Recommended value RPRE ≥ 6 kΩ; Imax = [48 / RPRE],
RPREmin = 6 kΩ
11
TRFB
LVCMOS_I
Transmitter Clock Edge Select Pin
TRFB = H; Parallel Interface Data is strobed on the Rising Clock Edge.
TRFB = L; Parallel Interface Data is strobed on the Falling Clock Edge
12
RAOFF
LVCMOS_I
Randomizer Control Input Pin
RAOFF = H, Backwards compatible mode for use with DS90C124 Deserializer.
RAOFF = L; Additional randomization ON (Default), Selects 2E7 LSFR setting.
See Table 1 for more details.
5, 8,
13
RES0
LVCMOS_I
Reserved. This pin MUST be tied LOW.
LVDS SERIAL INTERFACE PINS
20
DOUT+
LVDS_O
Transmitter LVDS True (+) Output.
This output is intended to be loaded with a 100Ω load to the DOUT+ pin. The interconnect should
be AC Coupled to this pin with a 100 nF capacitor.
19
DOUT−
LVDS_O
Transmitter LVDS Inverted (-) Output
This output is intended to be loaded with a 100Ω load to the DOUT- pin. The interconnect should
be AC Coupled to this pin with a 100 nF capacitor.
POWER / GROUND PINS
22
VDD
VDD
Analog Voltage Supply, LVDS Output POWER
21
VSS
GND
Analog Ground, LVDS Output GROUND
16
VDD
VDD
Analog Voltage Supply, VCO POWER
17
VSS
GND
Analog Ground, VCO GROUND
14
VDD
VDD
Analog Voltage Supply, PLL POWER
15
VSS
GND
Analog Ground, PLL GROUND
30
VDD
VDD
Digital Voltage Supply, Serializer POWER
31
VSS
GND
Digital Ground, Serializer GROUND
7
VDD
VDD
Digital Voltage Supply, Serializer Logic POWER
6
VSS
GND
Digital Ground, Serializer Logic GROUND
42
VDD
VDD
Digital Voltage Supply, Serializer INPUT POWER
43
VSS
GND
Digital Ground, Serializer Input GROUND
www.national.com
14
DS90UR241Q/DS90UR124Q
DS90UR124 Pin Diagram
Deserializer - DS90UR124
20194520
TOP VIEW
DS90UR124 Deserializer Pin Descriptions
Pin #
Pin Name
I/O/PWR
Description
LVCMOS PARALLEL INTERFACE PINS
35-38, ROUT[7:0]
41-44
LVCMOS_O
Receiver Parallel Interface Data Outputs – Group 1
19-22, ROUT[15:8]
27-30
LVCMOS_O
Receiver Parallel Interface Data Outputs – Group 2
7-10,
13-16
ROUT[23:16]
LVCMOS_O
Receiver Parallel Interface Data Outputs – Group 3
24
RCLK
LVCMOS_O
Parallel Interface Clock Output Pin. Strobe edge set by RRFB configuration pin.
CONTROL AND CONFIGURATION PINS
55
RRFB
LVCMOS_I
Receiver Clock Edge Select Pin
RRFB = H; ROUT LVCMOS Outputs strobed on the Rising Clock Edge.
RRFB = L; ROUT LVCMOS Outputs strobed on the Falling Clock Edge.
60
REN
LVCMOS_I
Receiver Data Enable
REN = H; ROUT[23-0] and RCLK are Enabled (ON).
REN = L; ROUT[23-0] and RCLK are Disabled (OFF), Receiver ROUT[23-0] and RCLK Outputs
are in TRI-STATE, PLL still operational and locked to TCLK.
48
RPWDNB
LVCMOS_I
Receiver Power Down Bar
RPWDNB = H; Receiver is Enabled and ON
RPWDNB = L; Receiver is in power down mode (Sleep), ROUT[23-0], RCLK, and LOCK are in
TRI-STATE stand-by mode, PLL is shutdown to minimize power consumption.
15
www.national.com
DS90UR241Q/DS90UR124Q
Pin #
Pin Name
I/O/PWR
Description
49
PTOSEL
LVCMOS_I
Progressive Turn On Operation Selection
PTO = H; ROUT[23:0] are grouped into three groups of eight, with each group switching about
±1 UI to ±2 UI apart relative to RCLK. (Figure 15)
PTO = L; PTO Spread Mode, ROUT[23:0] outputs are spread ±1 UI to ±2 UI and RCLK spread
±1 UI. (Figure 16) See Applications Informations section for more details.
63
RAOFF
LVCMOS_I
Randomizer Control Input Pin (See Table 2 for more details.)
RAOFF = H, Backwards compatible mode for use with DS90C241 Serializer.
RAOFF = L; Additional randomization ON (Default), Selects 2E7 LSFR setting.
64
SLEW
LVCMOS_I
LVCMOS Output Slew Rate Control
SLEW = L; Low drive output at 2 mA (default)
SLEW = H; High drive output at 4 mA
23
LOCK
LVCMOS_O
LOCK indicates the status of the receiver PLL
LOCK = H; receiver PLL is locked
LOCK = L; receiver PLL is unlocked, ROUT[23-0] and RCLK are at TRI-STATE.
50
RES0
LVCMOS_I
Reserved. This pin MUST be tied LOW.
NC
No Connection. Pins are not physically connected to the die. Recommendation is to leave pin
open or tie it to LOW.
1-6,
RES0
17, 18,
33, 34
BIST MODE PINS(See Applications Informations section for more details.)
61
BISTEN
LVCMOS_I
Control Pin for BIST Mode Enable
BISTEN = L; Default at Low, Normal Mode.
BISTEN = H; BIST mode active. When BISTEN = H and DS90UR241 DIN[23:0] = Low or
Floating; device will go to BIST mode accordingly. Check PASS output pin for test status.
62
BISTM
LVCMOS_I
BIST Mode selection. Control pin for which Deserializer is set for BIST reporting mode.
BISTM = L; Default at Low, Status of all ROUT with respective bit error on cycle-by-cycle basis
BISTM = H; Total accumulated bit error count provided on ROUT[7:0] (binary counter up to 255)
45
PASS
LVCMOS_O
Pass flag output for @Speed BIST Test operation.
PASS = L; BIST failure
PASS = H; LOCK = H before BIST can be enabled, then 1x10-9 error rate achieved across link.
LVDS SERIAL INTERFACE PINS
53
RIN+
LVDS_I
Receiver LVDS True (+) Input — This input is intended to be terminated with a 100Ω load to
the RIN+ pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor.
54
RIN−
LVDS_I
Receiver LVDS Inverted (−) Input — This input is intended to be terminated with a 100Ω load
to the RIN- pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor.
POWER / GROUND PINS
51
VDD
VDD
Analog LVDS Voltage Supply, POWER
52
VSS
GND
Analog LVDS GROUND
59
VDD
VDD
Analog Voltage Supply, PLL POWER
58
VSS
GND
Analog Ground, PLL GROUND
57
VDD
VDD
Analog Voltage supply, PLL VCO POWER
56
VSS
GND
Analog Ground, PLL VCO GROUND
32
VDD
VDD
Digital Voltage Supply, LOGIC POWER
31
VSS
GND
Digital Ground, Logic GROUND
46
VDD
VDD
Digital Voltage Supply, LOGIC POWER
47
VSS
GND
Digital Ground, LOGIC GROUND
40
VDD
VDD
Digital Voltage Supply, LVCMOS Output POWER
39
VSS
GND
Digital Ground, LVCMOS Output GROUND
26
VDD
VDD
Digital Voltage Supply, LVCMOS Output POWER
25
VSS
GND
Digital Ground, LVCMOS Output GROUND
11
VDD
VDD
Digital Voltage Supply, LVCMOS Output POWER
12
VSS
GND
Digital Ground, LVCMOS Output GROUND
www.national.com
16
The DS90UR241 Serializer and DS90UR124 Deserializer
chipset is an easy-to-use transmitter and receiver pair that
sends 24-bits of parallel LVCMOS data over a single serial
LVDS link from 120 Mbps to 1.03 Gbps throughput. The
DS90UR241 transforms a 24-bit wide parallel LVCMOS data
into a single high speed LVDS serial data stream with embedded clock and scrambles / DC Balances the data to enhance signal quality to support AC coupling. The DS90UR124
receives the LVDS serial data stream and converts it back into
a 24-bit wide parallel data and recovered clock. The 24-bit
Serializer/Deserializer chipset is designed to transmit data up
to 10 meters over shielded twisted pair (STP) at clock speeds
from 5 MHz to 43MHz.
The Deserializer can attain lock to a data stream without the
use of a separate reference clock source; greatly simplifying
system complexity and overall cost. The Deserializer synchronizes to the Serializer regardless of data pattern, delivering true automatic “plug and lock” performance. It will lock
to the incoming serial stream without the need of special
training patterns or sync characters. The Deserializer recovers the clock and data by extracting the embedded clock
information and validating data integrity from the incoming
data stream and then deserializes the data. The Deserializer
monitors the incoming clock information, determines lock status, and asserts the LOCK output high when lock occurs.
In addition the Deserializer also supports an optional
@SPEED BIST (Built In Self Test) mode, BIST error flag, and
LOCK status reporting pin. Signal quality on the wide parallel
output is controlled by the SLEW control and bank slew
(PTOSEL) inputs to help reduce noise and system EMI. Each
device has a power down control to enable efficient operation
in various applications.
DATA TRANSFER
After Serializer lock is established, the inputs DIN0–
DIN23 are used to input data to the Serializer. Data is clocked
into the Serializer by the TCLK input. The edge of TCLK used
to strobe the data is selectable via the TRFB pin. TRFB high
selects the rising edge for clocking data and low selects the
falling edge. The Serializer outputs (DOUT±) are intended to
drive point-to-point connections.
CLK1, CLK0, DCA, DCB are four overhead bits transmitted
along the single LVDS serial data stream (Figure 21). The
CLK1 bit is always high and the CLK0 bit is always low. The
CLK1 and CLK0 bits function as the embedded clock bits in
the serial stream. DCB functions as the DC Balance control
bit. It does not require any pre-coding of data on transmit side.
The DC Balance bit is used to minimize the short and longterm DC bias on the signal lines. This bit operates by selectively sending the data either unmodified or inverted. The
DCA bit is used to validate data integrity in the embedded data
stream. Both DCA and DCB coding schemes are integrated
and automatically performed within Serializer and Deserializer.
The chipset supports clock frequency ranges of 5 MHz to 43
MHz. Every clock cycle, 24 databits are sent along with 4 additional overhead control bits. Thus the line rate is 1.20 Gbps
maximum (140Mbps minimum). The link is extremely efficient
at 86% (24/28). Twenty five (24 data + 1 clock) plus associated ground signals are reduced to only 1 single LVDS pair
providing a compression ratio of better then 25 to 1.
In the serialized data stream, data/embedded clock & control
bits (24+4 bits) are transmitted from the Serializer data output
(DOUT±) at 28 times the TCLK frequency. For example, if
TCLK is 43 MHz, the serial rate is 43 x 28 = 1.20 Giga bits per
second. Since only 24 bits are from input data, the serial
“payload” rate is 24 times the TCLK frequency. For instance,
if TCLK = 43 MHz, the payload data rate is 43 x 24 = 1.03
Gbps. TCLK is provided by the data source and must be in
the range of 5 MHz to 43 MHz nominal. The Serializer outputs
(DOUT±) can drive a point-to-point connection as shown in
Figure 20. The outputs transmit data when the enable pin
(DEN) is high and TPWDNB is high. The DEN pin may be
used to TRI-STATE the outputs when driven low.
When the Deserializer channel attains lock to the input from
a Serializer, it drives its LOCK pin high and synchronously
delivers valid data and recovered clock on the output. The
Deserializer locks onto the embedded clock, uses it to generate multiple internal data strobes, and then drives the recovered clock to the RCLK pin. The recovered clock (RCLK
output pin) is synchronous to the data on the ROUT[23:0]
pins. While LOCK is high, data on ROUT[23:0] is valid. Otherwise, ROUT[23:0] is invalid. The polarity of the RCLK edge
is controlled by the RRFB input. ROUT[23:0], LOCK and
RCLK outputs will each drive a maximum of 4 pF load with a
43 MHz clock. REN controls TRI-STATE for ROUTn and the
RCLK pin on the Deserializer.
INITIALIZATION AND LOCKING MECHANISM
Initialization of the DS90UR241 and DS90UR124 must be
established before each device sends or receives data. Initialization refers to synchronizing the Serializer’s and
Deserializer’s PLL’s together. After the Serializers locks to the
input clock source, the Deserializer synchronizes to the Serializers as the second and final initialization step.
Step 1: When VDD is applied to both Serializer and/or Deserializer, the respective outputs are held in TRI-STATE and
internal circuitry is disabled by on-chip power-on circuitry.
When VDD reaches VDD OK (~2.2V) the PLL in Serializer begins locking to a clock input. For the Serializer, the local clock
is the transmit clock, TCLK. The Serializer outputs are held in
TRI-STATE while the PLL locks to the TCLK. After locking to
TCLK, the Serializer block is now ready to send data patterns.
The Deserializer output will remain in TRI-STATE while its
PLL locks to the embedded clock information in serial data
stream. Also, the Deserializer LOCK output will remain low
until its PLL locks to incoming data and sync-pattern on the
RIN± pins.
Step 2: The Deserializer PLL acquires lock to a data stream
without requiring the Serializer to send special patterns. The
Serializer that is generating the stream to the Deserializer will
automatically send random (non-repetitive) data patterns during this step of the Initialization State. The Deserializer will
lock onto embedded clock within the specified amount of time.
An embedded clock and data recovery (CDR) circuit locks to
the incoming bit stream to recover the high-speed receive bit
clock and re-time incoming data. The CDR circuit expects a
coded input bit stream. In order for the Deserializer to lock to
a random data stream from the Serializer, it performs a series
17
www.national.com
DS90UR241Q/DS90UR124Q
of operations to identify the rising clock edge and validates
data integrity, then locks to it. Because this locking procedure
is independent on the data pattern, total random locking duration may vary. At the point when the Deserializer’s CDR
locks to the embedded clock, the LOCK pin goes high and
valid RCLK/data appears on the outputs. Note that the LOCK
signal is synchronous to valid data appearing on the outputs.
The Deserializer’s LOCK pin is a convenient way to ensure
data integrity is achieved on receiver side.
Functional Description
DS90UR241Q/DS90UR124Q
and 100MΩ. Values less than 6kΩ should not be used. A lower input resistor value on the ”PRE” pin increases the magnitude of dynamic current during data transition. The additional
source current is based on the following formula: PRE =
(RPRE ≥ 6kΩ); IMAX = [48 / RPRE]. For example if Rpre =
15kΩ , then the Pre-Emphasis current is increase by an additional 3.2 mA.
The amount of Pre-Emphasis for a given media will depend
on the transmission distance of the application. In general, too
much Pre-Emphasis can cause over or undershoot at the receiver input pins. This can result in excessive noise, crosstalk
and increased power dissipation. For short cables or distances, Pre-Emphasis may not be required. Signal quality
measurements are recommended to determine the proper
amount of Pre-Emphasis for each application.
RESYNCHRONIZATION
If the Deserializer loses lock, it will automatically try to re-establish lock. For example, if the embedded clock edge is not
detected one time in succession, the PLL loses lock and the
LOCK pin is driven low. The Deserializer then enters the operating mode where it tries to lock to a random data stream.
It looks for the embedded clock edge, identifies it and then
proceeds through the locking process.
The logic state of the LOCK signal indicates whether the data
on ROUT is valid; when it is high, the data is valid. The system
may monitor the LOCK pin to determine whether data on the
ROUT is valid.
POWERDOWN
The Powerdown state is a low power sleep mode that the Serializer and Deserializer may use to reduce power when no
data is being transferred. The TPWDNB and RPWDNB are
used to set each device into power down mode, which reduces supply current to the µA range. The Serializer enters
powerdown when the TPWDNB pin is driven low. In powerdown, the PLL stops and the outputs go into TRI-STATE,
disabling load current and reducing current supply. To exit
Powerdown, TPWDNB must be driven high. When the Serializer exits Powerdown, its PLL must lock to TCLK before it
is ready for the Initialization state. The system must then allow
time for Initialization before data transfer can begin. The Deserializer enters powerdown mode when RPWDNB is driven
low. In powerdown mode, the PLL stops and the outputs enter
TRI-STATE. To bring the Deserializer block out of the powerdown state, the system drives RPWDNB high.
Both the Serializer and Deserializer must reinitialize and relock before data can be transferred. The Deserializer will
initialize and assert LOCK high when it is locked to the embedded clock.
AC-COUPLING AND TERMINATION
The DS90UR241 and DS90UR124 supports AC-coupled interconnects through integrated DC balanced encoding/decoding scheme. To use the Serializer and Deserializer in an
AC coupled application, insert external AC coupling capacitors in series in the LVDS signal path as illustrated in Figure
20. The Deserializer input stage is designed for AC-coupling
by providing a built-in AC bias network which sets the internal
VCM to +1.8V. With AC signal coupling, capacitors provide the
ac-coupling path to the signal input.
For the high-speed LVDS transmissions, the smallest available package should be used for the AC coupling capacitor.
This will help minimize degradation of signal quality due to
package parasitics. The most common used capacitor value
for the interface is 100 nF (0.1 uF) capacitor. NPO class 1 or
X7R class 2 type capacitors are recommended. 50 WVDC
should be the minimum used for the best system-level ESD
performance.
A termination resistor across DOUT± and RIN± is also required for proper operation to be obtained. The termination
resistor should be equal to the differential impedance of the
media being driven. This should be in the range of 90 to 132
Ohms. 100 Ohms is a typical value common used with standard 100 Ohm transmission media. This resistor is required
for control of reflections and also completes the current loop.
It should be placed as close to the Serializer DOUT± outputs
and Deserializer RIN± inputs to minimize the stub length from
the pins. To match with the deferential impedance on the
transmission line, the LVDS I/O are terminated with 100 Ohm
resistors on Serializer DOUT± outputs pins and Deserializer
RIN± input pins.
TRI-STATE
For the Serializer, TRI-STATE is entered when the DEN or
TPWDNB pin is driven low. This will TRI-STATE both driver
output pins (DOUT+ and DOUT−). When DEN is driven high,
the serializer will return to the previous state as long as all
other control pins remain static (TPWDNB, TRFB).
When you drive the REN or RPWDNB pin low, the Deserializer enters TRI-STATE. Consequently, the receiver output
pins (ROUT0–ROUT23) and RCLK will enter TRI-STATE.
The LOCK output remains active, reflecting the state of the
PLL. The Deserializer input pins are high impedance during
receiver powerdown (RPWDNB low) and power-off (VDD =
0V).
Receiver Termination Option 1
A single 100 Ohm termination resistor is placed across the
RIN± pins (see Figure 20). This provides the signal termination at the Receiver inputs. Other options may be used to
increase noise tolerance.
PRE-EMPHASIS
The DS90UR241 features a Pre-Emphasis function used to
compensate for long or lossy transmission media. Cable drive
is enhanced with a user selectable Pre-Emphasis feature that
provides additional output current during transitions to counteract cable loading effects. The transmission distance will be
limited by the loss characteristics and quality of the media.
Pre-Emphasis adds extra current during LVDS logic transition
to reduce the cable loading effects and increase driving distance. In addition, Pre-Emphasis helps provide faster transitions, increased eye openings, and improved signal integrity.
The ability of the DS90UR241 to use the Pre-Emphasis feature will extend the transmission distance up to 10 meters in
most cases.
To enable the Pre-Emphasis function, the “PRE” pin requires
one external resistor (Rpre) to Vss in order to set the additional current level. Values of Rpre should be between 6kΩ
www.national.com
Receiver Termination Option 2
For additional EMI tolerance, two 50 Ohm resistors may be
used in place of the single 100 Ohm resistor. A small capacitor
is tied from the center point of the 50 Ohm resistors to ground
(see Figure 22). This provides a high-frequency low
impedance path for noise suppression. Value is not critical,
4.7nF maybe used with general applications.
Receiver Termination Option 3
For high noise environments an additional voltage divider
network may be connected to the center point. This has the
advantage of a providing a DC low-impedance path for noise
suppression. Use resistor values in the range of 100Ω-2KΩ
18
transition to HIGH once a BER of 1x10-9 is achieved across
the transmission link.
BACKWARDS COMPATIBLE MODE WITH DS90C241
AND DS90C124
The RAOFF pin allows a backward compatible mode with
DS90C241/DS90C124 devices. To interface with either
DS90C241 Serializer or DS90C124 Deserializer, the RAOFF
pin on DS90UR241 or DS90UR124 must be tied HIGH to disable the additional LSFR coding. For normal operation directly with DS90UR241 to DS90UR124, RAOFF pins are set
LOW. See Table 1 and Table 2 for more details.
SIGNAL QUALITY ENHANCERS
The DS90UR124 Deserializer supports two signal quality enhancers. The SLEW pin is used to increase the drive strength
of the LVCMOS outputs when driving heavy loads. SLEW allows output drive strength for high or low current drive. Default
setting is LOW for low drive at 2 mA and HIGH for high drive
at 4 mA.
There are two types of Progressive Turn-On modes (Fixed
and PTO Frequency Spread) to help reduce EMI, simultaneous switching noise, and system ground bounce. The
PTOSEL pin introduces bank skew in the data/clock outputs
to limit the number of outputs switching simultaneously. For
Fixed-PTO mode, the Deserializer ROUT[23:0] outputs are
grouped into three groups of eight, with each group switching
about 2 or 1 UI apart in phase from RCLK for Group 1 and
Groups 2, 3 respectively (see Figure 15). In the PTO Frequency Spread mode, ROUT[23:0] are also grouped into
three groups of eight, with each group is separated out of
phase with the adjacent groups (see Figure 16) per every 4
cycles. Note that in the PTO Frequency Spread operating
mode RCLK is also spreading and separated by 1 UI.
Applications Information
USING THE DS90UR241 AND DS90UR124
The
DS90UR241/DS90UR124
Serializer/Deserializer
(SERDES) pair sends 24 bits of parallel LVCMOS data over
a serial LVDS link up to 1.03 Gbps. Serialization of the input
data is accomplished using an on-board PLL at the Serializer
which embeds clock with the data. The Deserializer extracts
the clock/control information from the incoming data stream
and deserializes the data. The Deserializer monitors the incoming clock information to determine lock status and will
indicate lock by asserting the LOCK output high.
DISPLAY APPLICATION
The DS90UR241/124 chipset is intended for interface between a host (graphics processor) and a Display. It supports
an 18-bit color depth (RGB666) and up to 1280 X 480 display
formats. In a RGB666 configuration 18 color bits (R[5:0], G
[5:0], B[5:0]), Pixel Clock (PCLK) and three control bits (VS,
HS and DE) along with three spare bits are supported across
the serial link with PCLK rates from 5 to 43 MHz.
@SPEED-BIST TEST FEATURE
To assist vendors with test verification, the DS90UR241/
DS90UR124 is equipped with built-in self-test (BIST) capability to support both system manufacturing and field diagnostics. BIST mode is intended to check the entire high-speed
serial link at full link-speed, without the use of specialized and
expensive test equipment. This feature provides a simple
method for a system host to perform diagnostic testing of both
Serializer and Deserializer. The BIST function is easily configured through the 2 control pins on the DS90UR124. When
the BIST mode is activated, the Serializer has the ability to
transfer an internally generated PRBS data pattern. This pattern traverses across interconnecting links to the Deserializer.
The DS90UR124 includes an on-chip PRBS pattern verification circuit that checks the data pattern for bit errors and
reports any errors on the data output pins on the Deserializer.
The @SPEED-BIST feature uses 2 signal pins (BISTEN and
BISTM) on the DS90UR124 Deserializer. The BISTEN and
BISTM pins together determine the functions of the BIST
mode. The BISTEN signal (HIGH) activates the test feature
on the Deserializer. After the BIST mode is enabled, all the
data input channels DIN[23:0] on the DS90UR241 Serializer
must be set logic LOW or floating in order for Deserializer to
start accepting data. An input clock signal (TCLK) for the Serializer must also be applied during the entire BIST operation.
The BISTM pin selects error reporting status mode of the
BIST function. When BIST is configured in the error status
mode (BISTM = LOW), each of the ROUT[23:0] outputs will
correspond to bit errors on a cycle-by-cycle basis. The result
of bit mismatches are indicated on the respective parallel inputs on the ROUT[23:0] data output pins. In the BIST errorcount accumulator mode (BISTM = HIGH), an 8-bit counter
on ROUT[7:0] is used to represent the number of errors detected (0 to 255 max). The successful completion of the BIST
test is reported on the PASS pin on the Deserializer. The
Deserializer's PLL must first be locked to ensure the PASS
status is valid. The PASS status pin will stay LOW and then
TYPICAL APPLICATION CONNECTION
Figure 18 shows a typical application of the DS90UR241 Serializer (SER). The LVDS outputs utilize a 100 ohm termination and 100nF coupling capacitors to the line. Bypass
capacitors are placed near the power supply pins. At a minimum, three 0.1uF capacitors should be used for local bypassing. A system GPO (General Purpose Output) controls
the TPWDNB pin. In this application the TRFB pin is tied High
to latch data on the rising edge of the TCLK. The DEN signal
is not used and is tied High also. The application is to the
companion Deserializer (DS90UR124) so the RAOFF pin is
tied low to scramble the data and improve link signal quality.
In this application the link is typical, therefore the VODSEL
pin is tied Low for the standard LVDS swing. The pre-emphasis input utilizes a resistor to ground to set the amount of preemphasis desired by the application.
Figure 19shows a typical application of the DS90UR124 Deserializer (DES). The LVDS inputs utilize a 100 ohm termination and 100nF coupling capacitors to the line. Bypass
capacitors are placed near the power supply pins. At a minimum, four 0.1uF capacitors should be used for local bypassing. A system GPO (General Purpose Output) controls the
RPWDNB pin. In this application the RRFB pin is tied High to
strobe the data on the rising edge of the RCLK. The REN
signal is not used and is tied High also. The application is to
the companion Serializer (DS90UR241) so the RAOFF pin is
tied low to descramble the data. Output (LVCMOS) signal
quality is set by the SLEW pin, and the PTOSEL pin can be
used to reduce simultaneous output switching by introducing
a small amount of delay between output banks.
19
www.national.com
DS90UR241Q/DS90UR124Q
for the pullup and pulldown. Ratio the resistor values to bias
the center point at 1.8V. For example (see Figure 23):
VDD=3.3V,
Rpullup=1KΩ,
Rpulldown=1.2KΩ;
or
Rpullup=100Ω, Rpulldown= 120Ω (strongest). The smaller
values will consume more bias current, but will provide enhanced noise suppression.
DS90UR241Q/DS90UR124Q
20194522
FIGURE 18. DS90UR241 Typical Application Connection
cable. In a point-to-point configuration, the transmission media needs be terminated at both ends of the transmitter and
receiver pair. Interconnect for LVDS typically has a differential
impedance of 100 Ohms. Use cables and connectors that
have matched differential impedance to minimize impedance
discontinuities. In most applications that involve cables, the
transmission distance will be determined on data rates involved, acceptable bit error rate and transmission medium.
POWER CONSIDERATIONS
An all LVCMOS design of the Serializer and Deserializer
makes them inherently low power devices. Additionally, the
constant current source nature of the LVDS outputs minimize
the slope of the speed vs. IDD curve of LVCMOS designs.
NOISE MARGIN
The Deserializer noise margin is the amount of input jitter
(phase noise) that the Deserializer can tolerate and still reliably recover data. Various environmental and systematic factors include:
Serializer: VDD noise, TCLK jitter (noise bandwidth and
out-of-band noise)
Media: ISI, VCM noise
Deserializer: VDD noise
For a graphical representation of noise margin, please see .
LIVE LINK INSERTION
The Serializer and Deserializer devices support live pluggable applications. The automatic receiver lock to random
data “plug & go” hot insertion capability allows the
DS90UR124 to attain lock to the active data stream during a
live insertion event.
TRANSMISSION MEDIA
The Serializer and Deserializer are to be used in point-to-point
configuration, through a PCB trace, or through twisted pair
www.national.com
20
DS90UR241Q/DS90UR124Q
20194523
FIGURE 19. DS90UR124 Typical Application Connection
ternal bypass capacitors should include both RF ceramic and
tantalum electrolytic types. RF capacitors may use values in
the range of 0.01 uF to 0.1 uF. Tantalum capacitors may be
in the 2.2 uF to 10 uF range. Voltage rating of the tantalum
capacitors should be at least 5X the power supply voltage
being used.
Surface mount capacitors are recommended due to their
smaller parasitics. When using multiple capacitors per supply
pin, locate the smaller value closer to the pin. A large bulk
capacitor is recommend at the point of power entry. This is
typically in the 50uF to 100uF range and will smooth low frequency switching noise. It is recommended to connect power
PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS
Circuit board layout and stack-up for the LVDS SERDES devices should be designed to provide low-noise power feed to
the device. Good layout practice will also separate high frequency or high-level inputs and outputs to minimize unwanted
stray noise pickup, feedback and interference. Power system
performance may be greatly improved by using thin dielectrics (2 to 4 mils) for power / ground sandwiches. This
arrangement provides plane capacitance for the PCB power
system with low-inductance parasitics, which has proven especially effective at high frequencies, and makes the value
and placement of external bypass capacitors less critical. Ex21
www.national.com
DS90UR241Q/DS90UR124Q
and ground pins directly to the power and ground planes with
bypass capacitors connected to the plane with via on both
ends of the capacitor. Connecting power or ground pins to an
external bypass capacitor will increase the inductance of the
path.
A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size reduces
the parasitic inductance of the capacitor. The user must pay
attention to the resonance frequency of these external bypass
capacitors, usually in the range of 20-30 MHz range. To provide effective bypassing, multiple capacitors are often used
to achieve low impedance between the supply rails over the
frequency of interest. At high frequency, it is also a common
practice to use two vias from power and ground pins to the
planes, reducing the impedance at high frequency.
Some devices provide separate power and ground pins for
different portions of the circuit. This is done to isolate switching noise effects between different sections of the circuit.
Separate planes on the PCB are typically not required. Pin
Description tables typically provide guidance on which circuit
blocks are connected to which power pin pairs. In some cases, an external filter many be used to provide clean power to
sensitive circuits such as PLLs.
Use at least a four layer board with a power and ground plane.
Locate LVCMOS signals away from the LVDS lines to prevent
coupling from the LVCMOS lines to the LVDS lines. Closelycoupled differential lines of 100 Ohms are typically recommended for LVDS interconnect. The closely coupled lines
help to ensure that coupled noise will appear as common-
mode and thus is rejected by the receivers. The tightly coupled lines will also radiate less.
Termination of the LVDS interconnect is required. For pointto-point applications, termination should be located at both
ends of the devices. Nominal value is 100 Ohms to match the
line’s differential impedance. Place the resistor as close to the
transmitter DOUT± outputs and receiver RIN± inputs as possible to minimize the resulting stub between the termination
resistor and device.
LVDS INTERCONNECT GUIDELINES
See AN-1108 and AN-905 for full details.
• Use 100Ω coupled differential pairs
• Use the S/2S/3S rule in spacings
—S = space between the pair
—2S = space between pairs
—3S = space to LVCMOS signal
• Minimize the number of Vias
• Use differential connectors when operating above
500Mbps line speed
• Maintain balance of the traces
• Minimize skew within the pair
• Terminate as close to the TX outputs and RX inputs as
possible
Additional general guidance can be found in the LVDS
Owner’s Manual - available in PDF format from the National
web site at: www.national.com/lvds
20194518
FIGURE 20. AC Coupled Application
20194526
*Note: bits [0-23] are not physically located in positions shown above since bits [0-23] are scrambled and DC Balanced
FIGURE 21. Single Serialized LVDS Bitstream*
www.national.com
22
DS90UR241Q/DS90UR124Q
20194524
FIGURE 22. Receiver Termination Option 2
20194525
FIGURE 23. Receiver Termination Option 3
Truth Tables
TABLE 1. DS90UR241 Serializer Truth Table
TPWDNB
(Pin 9)
DEN
(Pin 18)
RAOFF
(Pin 12)
Tx PLL Status
(Internal)
LVDS Outputs
(Pins 19 and 20)
L
X
X
X
Hi Z
H
L
X
X
Hi Z
H
H
X
Not Locked
Hi Z
H
H
L
Locked
Serialized Data with Embedded Clock
(DS90UR124 compatible)
H
H
H
Locked
Serialized Data with Embedded Clock
(DS90C124 compatible)
23
www.national.com
DS90UR241Q/DS90UR124Q
TABLE 2. DS90UR124 Deserializer Truth Table
RPWDNB
(Pin 48)
REN
(Pin 60)
RAOFF
(Pin 63)
Rx PLL Status
(Internal)
ROUTn and RCLK
(See Pin Diagram)
LOCK
(Pin 23)
L
X
X
X
Hi Z
Hi Z
H
L
X
X
Hi Z
L = PLL Unocked;
H = PLL Locked
H
H
X
Not Locked
Hi Z
L
H
H
L
Locked
Data and RCLK Active
(DS90UR241 compatible)
H
H
H
H
Locked
Data and RCLK Active
(DS90C241 compatible)
H
www.national.com
24
DS90UR241Q/DS90UR124Q
Physical Dimensions inches (millimeters) unless otherwise noted
Dimensions show in millimeters only
NS Package Number VBC48A
Dimensions show in millimeters only
NS Package Number VEC64A
25
www.national.com
DS90UR241Q/DS90UR124Q 5-43 MHz DC-Balanced 24-Bit FPD-Link II Serializer and Deserializer
Chipset
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage Reference
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Solutions
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
Wireless (PLL/VCO)
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2009 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]
Similar pages