H EE GEN FR ALO CAT93HC46 1-kb High Speed Microwire Serial EEPROM LE A D F R E ETM FEATURES ■ High speed operation: 4 MHz @ 5.0 V ■ Low power CMOS technology ■ 1.8 to 5.5 volt operation ■ 1,000,000 program/erase cycles ■ Selectable x8 or x16 word organization ■ 100 year data retention ■ Sequential Read ■ Industrial and extended temperature ranges ■ Software write protection ■ 8-Lead PDIP, SOIC, MSOP and TSSOP packages ■ Power-up inadvertent write protection DESCRIPTION The CAT93HC46 is a 1-kb Serial EEPROM memory device which is configured as registers of either 16 bits (ORG pin at VCC) or 8 bits (ORG pin at GND). Each register can be written (or read) serially by using the DI (or DO) pin. The CAT93HC46 is manufactured using Catalyst’s advanced CMOS EEPROM floating gate it n PIN CONFIGURATION DIP Package (P, L) 1 2 3 4 CS SK DI DO 8 7 6 5 VCC NC ORG GND SOIC Package (J, W) NC VCC CS SK 1 2 3 4 8 7 6 5 ORG GND DO DI is o c d e 1 2 3 4 8 7 6 5 D VCC NC ORG GND CS SK DI DO 1 2 3 4 8 7 6 5 u n FUNCTIONAL SYMBOL DO 1 2 3 4 8 7 6 5 DO DI CAT93HC46 SK CS VCC VSS NC ORG GND PIN FUNCTIONS Pin Name VCC NC ORG GND Note: When the ORG pin is connected to VCC, the X16 organization is selected. When it is connected to ground, the X8 pin is selected. If the ORG pin is left unconnected, then an internal pullup device will select the X16 organization. © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice VCC ORG TSSOP Package (U, Y) CS SK DI a P technology. The device is designed to endure 1,000,000 program/erase cycles and has a data retention of 100 years. The CAT93HC46 is available in 8-pin DIP, SOIC, MSOP or TSSOP packages. SOIC Package (S, V) MSOP Package (R, Z) CS SK DI DO t r 1 Function CS Chip Select SK Clock Input DI Serial Data Input DO Serial Data Output VCC 1.8 to 5.5 V Power Supply GND Ground ORG Memory Organization NC No Connection Doc. No. 1008,Rev. H CAT93HC46 ABSOLUTE MAXIMUM RATINGS* *COMMENT Temperature Under Bias .................. -55°C to +125°C Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. Storage Temperature ........................ -65°C to +150°C Pin with Respect to Ground(1) .... -2.0 V to VCC + 2.0 V VCC with Respect to Ground ................ -2.0 V to 7.0 V Lead Soldering Temperature (10 secs) ............ 300°C Output Short Circuit Current(2) ........................ 100 mA t r RELIABILITY CHARACTERISTICS Symbol Parameter Reference Test Method Min NEND(3) Endurance MIL-STD-883, Test Method 1033 1,000,000 TDR(3) Data Retention MIL-STD-883, Test Method 1008 100 VZAP(3) ESD Susceptibility MIL-STD-883, Test Method 3015 2000 ILTH(3)(4) Latch-Up JEDEC Standard 17 D.C. OPERATING CHARACTERISTICS Industrial Temperature Range (-40°C to 85°C) Symbol Parameter ICC1 Power Supply Current (Write) ICC2 Power Supply Current (Read) ISB1 Standby Supply Current (x8) ISB2(5) Standby Supply Current (x16) ILI Input Leakage Current ILO Output Leakage Current VIL1 VIH1 VIL2 VIH2 VOL1 VOH1 VOL2 VOH2 it n Min o c 0 Max a P Max Units Cycles/Byte Years d e 100 u n Limits Typ Typ Volts mA Units Test Conditions mA fSK = 4 MHz, VCC = 5.0 V 200 µA fSK = 4 MHz, VCC = 5.0 V 10 µA CS = GND, ORG=GND 10 µA CS = GND, ORG = Float or VCC 1 µA VIN = 0 V to VCC, CS = GND 1 µA VOUT = 0 V to VCC, CS = GND 2 -0.1 0.8 4.5 V ≤ VCC < 5.5 V 2 VCC + 1 4.5 V ≤ VCC < 5.5 V Input Low Voltage 0 VCC x 0.2 1.8 V ≤ VCC < 4.5 V Input High Voltage VCC x 0.7 VCC + 1 1.8V ≤ VCC < 4.5 V 0.4 4.5 V ≤ VCC < 5.5 V, IOL = 2.1 mA s i D Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage 2.4 V Output Low Voltage Output High Voltage 0.2 4.5 V ≤ VCC < 5.5 V, IOH = -400 µA 1.8 V ≤ VCC < 4.5 V, IOL = 1 mA 1.8 V ≤ VCC < 4.5 V, IOH = -100 µA VCC - 0.2 Note: (1) The minimum DC input voltage is -0.5 V. During transitions, inputs may undershoot to -2.0 V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC + 0.5 V, which may overshoot to VCC + 2.0 V for periods of less than 20 ns. (2) Output shorted for no more than one second. (3) This parameter is tested initially and after a design or process change that affects the parameter. (4) Latch-up protection is provided for stresses up to 100 mA on I/O pins from -1 V to VCC + 1 V. (5) Standby Current (ISB2) = 0 µA (<900 nA). Doc. No. 1008, Rev. H 2 CAT93HC46 POWER-UP TIMING (1)(2) Symbol Parameter tPUR tPUW Min Typ Max Units Power-up to Read Operation 1 ms Power-up to Write Operation 1 ms t r A.C. CHARACTERISTICS Industrial Temperature Range (-40°C to 85°C) 1.8 V - 5.5 V a P 2.5 V - 5.5 V 4.5 V - 5.5 V Symbol Parameter Min Max Min Max Min Max Units SKMAX Maximum Clock Frequency DC 1 DC 2 DC 4 MHz tCSS CS Setup Time 240 120 60 tCSH CS Hold Time 0 0 0 tDIS DI Setup Time 240 120 tDIH DI Hold Time 240 120 tPD1 Output Delay to 1 480 240 120 ns tPD0 Output Delay to 0 480 240 120 ns tHZ(1) Output Delay to High-Z 240 120 60 ns tCSMIN Minimum CS Low Time tSKHI Minimum SK High Time tSKLOW Minimum SK Low Time tSV Output Delay to Status Valid 480 240 120 ns tEW Program/Erase Pulse Width 5 5 5 ms it n 240 480 240 o c d e 240 ns 60 120 Conditions ns 60 u n 120 ns Test ns 60 ns 120 ns 60 ns CL = 100 pF (3) NOTE: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. (3) The input levels and timing reference points are shown in the “AC Test Conditions” table. s i D A.C. TEST CONDITIONS Input Rise and Fall Times ≤ 10 ns Input Pulse Voltages 0.4 V to 2.4 V 4.5 V ≤ VCC ≤ 5.5 V Timing Reference Voltages 0.8 V, 2.0 V 4.5 V ≤ VCC ≤ 5.5 V Input Pulse Voltages VCC x 0.2 to VCC x 0.8 1.8 V ≤ VCC ≤ 4.5 V Timing Reference Voltages VCC x 0.5 1.8 V ≤ VCC ≤ 4.5 V 3 Doc. No. 1008, Rev. H CAT93HC46 DEVICE OPERATION The ready/busy status can be determined after the start of a write operation by selecting the device (CS high) and polling the DO pin; DO low indicates that the write operation is not completed, while DO high indicates that the device is ready for the next instruction. If necessary, the DO pin may be placed back into a high impedance state by shifting a dummy “1” into the DI pin. The DO pin will enter the high impedance state on the falling edge of the clock (SK). Placing the DO pin into the high impedance state is recommended in applications where the DI pin and the DO pin are to be tied together to form a common DI/O pin. The CAT93HC46 is a 1024-bit nonvolatile memory intended for use with industry standard microprocessors. The CAT93HC46 can be organized as registers of either 16 bits or 8 bits. When organized as X16, seven 9-bit instructions control the reading, writing and erase operations of the device. When organized as X8, seven 10-bit instructions control the operation of the device. The CAT93HC46 operates on a single power supply and will generate on chip the high voltage required during write operation. Instructions, addresses, and data are clocked into the DI pin on the rising edge of the clock (SK). The DO pin is normally in a high impedance state, except when reading data from the device, or when checking the ready/busy status after a write operation. d e INSTRUCTION SET Instruction Start Bit Opcode Address x8 x16 READ 1 10 A6-A0 ERASE 1 11 A6-A0 WRITE 1 01 A6-A0 EWEN 1 00 11XXXXX EWDS 1 00 00XXXXX ERAL 1 00 10XXXXX WRAL 1 00 01XXXXX s i D x8 it n A5-A0 o c u n Data A5-A0 A5-A0 D7-D0 11XXXX 00XXXX x16 a P D7-D0 Comments Read Address AN–A0 Clear Address AN–A0 D15-D0 Write Address AN–A0 Write Enable Write Disable Clear All Addresses 10XXXX 01XXXX t r The format for all instructions sent to the device is a logical "1" start bit, a 2-bit (or 4-bit) opcode, 6-bit byte/ word address (an additional bit when organized X8) and for write operations a 16-bit data field (8-bit for X8 organization). D15-D0 Write All Addresses Figure 1. Sychronous Data Timing SK DI tSKHI tSKLOW tCSH tDIS tDIH VALID VALID tCSS CS tDIS tPD0,tPD1 DO Doc. No. 1008, Rev. H DATA VALID 4 tCSMIN CAT93HC46 Read Write Upon receiving a READ command and an address (clocked into the DI pin), the DO pin of the CAT93HC46 will come out of the high impedance state; after an initial dummy zero bit, data will be shifted out, MSB first. The output will toggle on the rising edge of the SK clock and will be stable after the specified time delay (tPD0 or tPD1) After receiving a WRITE command, address and data, the CS (Chip Select) pin must be deselected for a minimum of tCSMIN. The falling edge of CS will start the self-timed clear and data store cycle into the specified memory location. The clocking of the SK pin is not necessary after the device has entered the self-timed mode. (Note 1.) The ready/busy status of the CAT93HC46 can be determined by selecting the device and polling the DO pin. Since this device features Auto-Clear before write, it is NOT necessary to erase a memory location before it is written into. After the 1st data word has been shifted out and CS remains asserted with the SK clock continuing to toggle, the CAT93HC46 will automatically increment to the next address and shift out the next data word. As long as CS is continuously asserted and SK continues to toggle, the device will keep incrementing to the next address automatically until it reaches the end of the address space, then loops back to address 0. In the sequential READ mode, only the initial data word is preceeded by a dummy zero bit; all subsequent data words will follow without a dummy zero bit. it n Figure 2a. Read Instruction Timing SK CS o c AN DI DO 1 1 AN—1 0 s i D HIGH-Z t r a P Erase Upon receiving an ERASE command and address, the CS (Chip Select) pin must be deasserted for a minimum of tCSMIN. The falling edge of CS will start the self-timed clear cycle of the selected memory location. The clocking of the SK pin is not necessary after the device has entered the self-timed mode. (Note 1.) The ready/busy status of the CAT93HC46 can be determined by selecting the device and polling the DO pin. Once cleared, the content of a cleared location returns to a logical “1” state. d e u n tCS MIN STANDBY A0 tPD0 tHZ HIGH-Z 0 DN DN—1 D1 D0 Figure 2b. Sequential Read Instruction Timing SK 1 1 1 1 1 AN AN–1 1 1 1 1 1 1 1 1 1 1 CS DI DO 1 Don't Care 1 A0 0 HIGH-Z Dummy 0 D15 . . . D0 or D7 . . . D0 5 Address + 1 D15 . . . D0 or D7 . . . D0 Address + 2 D15 . . . D0 or D7 . . . D0 Address + n D15 . . . or D7 . . . Doc. No. 1008, Rev. H CAT93HC46 Erase/Write Enable and Disable Write All The CAT93HC46 powers up in the write disable state. Any writing after power-up or after an EWDS (write disable) instruction must first be preceded by the EWEN (write enable) instruction. Once write is enabled, it will remain enabled until power to the device is removed, or the EWDS instruction is sent. The EWDS instruction can be used to disable all CAT93HC46 write and clear instructions, and will prevent any accidental writing or clearing of the device. Data can be read normally from the device regardless of the write enable/disable status. Upon receiving a WRAL command and data, the CS (Chip Select) pin must be deselected for a minimum of tCSMIN. The falling edge of CS will start the self-timed data write to all memory locations in the device. The clocking of the SK pin is not necessary after the device has entered the self-timed mode. The ready/busy status of the CAT93HC46 can be determined by selecting the device and polling the DO pin. It is not necessary for all memory locations to be cleared before the WRAL command is executed. Once written, the contents of all memory locations will return to a logical “0” state. Erase All Figure 3. Write Instruction Timing it n SK CS AN DI 1 o c 0 DO AN-1 1 s i D A0 t r a P Note 1: After the last data bit has been sampled, Chip Select (CS) must be brought Low before the next rising edge of the clock (SK) in order to start the self-timed high voltage cycle. This is important because if the CS is brought low before or after this specific frame window, the addressed location will not be programmed or erased. Upon receiving an ERAL command, the CS (Chip Select) pin must be deselected for a minimum of tCSMIN. The falling edge of CS will start the self-timed clear cycle of all memory locations in the device. The clocking of the SK pin is not necessary after the device has entered the self-timed mode. (Note 1.) The ready/busy status of the CAT93HC46 can be determined by selecting the device and polling the DO pin. Once cleared, the contents of all memory locations will return to a logical “1” state. d e u n DN tCS MIN STANDBY STATUS VERIFY D0 tSV tHZ BUSY HIGH-Z READY HIGH-Z tEW Figure 4. Erase Instruction Timing SK CS STATUS VERIFY AN DI 1 1 tCS MIN A0 AN-1 STANDBY 1 tHZ tSV HIGH-Z DO BUSY READY HIGH-Z tEW Doc. No. 1008, Rev. H 6 CAT93HC46 Figure 5. EWEN/EWDS Instruction Timing SK STANDBY CS DI 1 0 0 a P * ENABLE=11 DISABLE=00 d e Figure 6. ERAL Instruction Timing SK CS DI 1 0 1 0 o c s i D Figure 7. WRAL Instruction Timing SK CS DI it n 0 HIGH-Z DO 1 0 0 t r * u n STATUS VERIFY STANDBY tCS MIN tSV tHZ BUSY READY HIGH-Z tEW STATUS VERIFY STANDBY tCS MIN 0 DN 1 D0 tSV tHZ DO BUSY READY HIGH-Z tEW 7 Doc. No. 1008, Rev. H CAT93HC46 ORDERING INFORMATION Prefix Device # Suffix 93HC46 CAT Optional Company ID -1.8 I S Temperature Range Blank = Commercial (0¡C to +70¡C) I = Industrial (-40¡C to +85¡C) A = Automotive (-40¡C to +105¡C) E = Extended (-40ßC to +125ßC) Product Number 93HC46: 1K Package P = PDIP S = SOIC (JEDEC) J = SOIC (JEDEC) U = TSSOP * available upon request Rev H(2) TE13 Tape & Reel a P Operating Voltage Blank (Vcc=2.5 to 6.0V) 1.8 (Vcc=1.8 to 6.0V) it n u n d e Notes: (1) The device used in the above example is a 93HC46SI-TE13 (SOIC, Industrial Temperature,Tape & Reel). (2) Product die revision letter is marked on top of the package as a suffix to the production date code (e.g., AYWWH.) For additional information, please contact your Catalyst sales office. o c s i D Doc. No. 1008, Rev. H 8 t r Die Revision REVISION HISTORY Date Rev. Reason 11/11/2003 E Updated Features Eliminated Commercial temperature range Updated DC Operating Characteristics Updated AC Characteristics t r Updated Ordering Information 11/14/2003 F Updated DC Operating Characteristics 7/27/2004 G Add die revision to Ordering Information 03/11/2005 H Updated Ordering Information d e Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: DPP ™ AE2 ™ u n a P Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents issued to Catalyst Semiconductor contact the Company’s corporate office at 408.542.1000. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. it n Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. o c Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. s i D Catalyst Semiconductor, Inc. Corporate Headquarters 1250 Borregas Avenue Sunnyvale, CA 94089 Phone: 408.542.1000 Fax: 408.542.1200 www.catalyst-semiconductor.com Publication #: Revison: Issue date: Type: 1008 H 03/11/05 Final