DATA SHEET GS1A~GS1M SURFACE MOUNT RECTIFIER VOLTAGE- 50 to 1000 Volts CURRENT - 1.0 Ampere SMA / DO-214AC Unit: inch ( mm ) FEATURES .114 (2.90) .098 (2.50) • For surface mounted applications • Low profile package .062 (1.60) .055 (1.40) • Built-in strain relief • Easy pick and place • Plastic package has Underwriters Laboratory Flammability Classification 94V-O • Glass passivated chip junction • High temperature soldering : 260°C /10 seconds at terminals .181 (4.60) .157 (4.00) .012 (.305) MECHANICAL DATA .006 (.152) .096 (2.30) .078 (2.00) Case: JEDEC DO-214AC molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard packaging: 12mm tape (EIA-481) Weight: 0.002 ounce, 0.064 gram .008(.203) .002(.051) .060 (1.52) .030 (0.76) .208 (5.28) .188 (4.80) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. SYMBOLS GS1A GS1B GS1D GS1G GS1J GS1K GS1M UNIT Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 V Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 100 V Maximum Average Forward Rectified Current, at T L =75°C Peak Forward Surge Current 8.3ms single half sine-wave I(AV) 1.0 A superimposed on rated load (JEDEC method) IFSM 30.0 A Maximum Instantaneous Forward Voltage at 1.0A VF 1.10 V 5.0 µA 50.0 µA Maximum DC Reverse Current at Rated DC Blocking Voltage TA=25°C TA=125°C IR Maximum Reverse Recovery Time(Note 1) T J =25°C TRR 2.5 µs Typical Junction Capacitance (Note 2) CJ 12 pF Maximum Thermal Resistance(Note 3) RθJA RθJA 30.0 °C/ W Operating and Storage Temperature Range TJ,TSTG NOTES:1. Reverse Recovery Test Conditions: I F =0.5A, I R =1.0A, I rr =0.25A 2. Measured at 1 MHz and applied V r = 4.0 volts. 3. 8.0 mm 2 ( .013mm thick ) land areas. -55 to +150 °C INSTANTANEOUS FORWARD CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES AVERAGE FORWARD CURRENT AMPERES 3.0 2.5 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.315 X 0.315" ( 8.0 X 8.0mm ) COPPER PAD AREAS 2.0 1.5 1.0 0.5 0 0 50 100 100 40 20 10 4.0 2.0 1.0 0.4 0.2 0.1 0.4 150 O TEMPERATURE C Fig. 1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FPRWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) 100 O T J =100 C 10 T J =75 OC 1.0 0.1 T J =25 OC 0.01 0.001 0 20 40 60 80 100 120 140 0.8 1.2 1.0 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 2- TYPICAL INSTANTANEOUS FORWARD CHARACTERISITCS PER ELEMENT 30 25 20 15 10 5 0 1 6 2 10 20 40 60 100 NO. OF CYCLES AT 62Hz Fig. 4- MAXIMUM NON-REPETITEVE PEAK FORWARD SURGE CURRENT PERCENT OF PEAK REVERSE VOLTAGE Fig. 3- TYPICAL REAK REVERSE CHARACTERISTICS 100 100 50 50 O CAPACITANCE, pF THERMAL IMPEDANCE( OC/W) 0.6 20 10 2 2 Units Mounted On 20in (5.4mm ) +0.5mil inches(0.013mm) Thick Copper Land Areas 5 Tj=25 C f=1.0MHz Vsig=50mVp-p 20 10 5 2 2 1 0.01 1 0.1 0.1 1.0 10 HEATING TIME(SEC) Fig. 5- TRANSIENT THERMAL IMPEDANCE 100 1.0 10 100 1000 REVERSE VOLTAGE, VOLTS Fig. 6- TYPICL JUNCTION CAPACITANCE PER ELEMENT