MCH03 Ceramic capacitors Multi-layer ceramic chip capacitors MCH03 (0603 (0201) size, chip capacitor) zFeatures 1) Ultra miniature (0.6mm×0.3mm×0.3mm), Ultra light weight (0.3mg) 2) Suitable for mobile devices 3) Lead-free plating terminal 4) No polarity zQuick Reference The design and specifications are subject to change without prior notice. Please check the most recent technical specifications prior to placing orders or using the product. For more detail information regarding packaging style code, please check product designation. Thermal compensation Part No. Size code Temperature characteristics (ppm/°C) code Operating temp. range (°C) Rated voltage (V) Capacitance (pF) 25 0.5 to 2.7 (E12 Series) ∗ 3.0 to 3.9 (E12 Series) ∗ 4 to 5 (E12 Series) ∗ 5.1 to 10 (E12 Series) ∗ 11 to 100 (E12 Series) 0±250(CK) 0±120(CJ) MCH03 0603 −55 to +125 A (AN) 0±60(CH) Capacitance tolerance Thickness (mm) C(±0.25pF) D(±0.5pF) J(±5%) 0.3 ± 0.03 ∗ : 0.5pF/0.75pF/2pF/3pF/4pF/5pF/6pF/7pF/8pF/9pF available zHigh dielectric constant Part No. Size code Temperature characteristics code Operating temp. range (°C) ±10%(B) CN MCH03 0603 FN ±15% (R) (X7R) Capacitance (pF) Capacitance tolerance 100 to 2,200 (E6 Series) 4,700 (E3 Series) 100 to 2,200 (E6 Series) 4,700 (E3 Series) 10,000 (E6 Series) K (±10%) −55 to +85 25 16 25 16 6.3 −25 to +85 16 10,000 (E1 Series) −30 to +85 16 10,000 (E1 Series) −25 to +85 −55 to +125 ±15%(X5R) +30%, −80% (F) +22%, −82% (Y5V) Rated voltage (V) Thickness (mm) 0.3 ± 0.03 Z (+80%, −20%) zExternal dimensions (Unit : mm) 0.1Min. 0.17Min. 0.3±0.03 0.3±0.03 0.3±0.03 0.6±0.03 0.3±0.03 Rev.A 1/12 MCH03 Ceramic capacitors zProduct designation Code Prduct thickness K 0.3mm Packing specification Reel Basic ordering unit(pcs.) Paper tape(width 8mm, pitch 2mm) φ180mm (7in.) 15,000 Packaging Style Part No. M C H Rated voltage Code Voltage 8 6.3V 3 16V 2 25V 0 3 3 F N 1 0 3 Temperature characteristic code :Refer to quick reference table. Z K Nominal capacitance Capacitance tolerance Tolerance Code K ±0.25pF(0.5 to 5pF) ±0.5pF(5.1 to 10pF) ±5%(11pF or more) ±10% Z +80%, −20% C 3-digit designation accordijg to IEC D J zProduct No.list •Thermal compensation capacitors Capacitance (pF) 0.5 0.75 1.0 1.2 1.5 1.8 2.0 2.2 2.7 3.0 3.3 3.9 4.0 4.7 5.0 5.6 6 6.8 7 8 8.2 9 10 Temperature A AN(CG) (COG) (CH) Characteristic 25V Rated voltage (V) Product No. Tolerance Product thickness(mm) MCH032A (AN) 0R5CK MCH032A (AN) R75CK MCH032A (AN) 010CK MCH032A (AN) 1R2CK MCH032A (AN) 1R5CK MCH032A (AN) 1R8CK MCH032A (AN) 020CK MCH032A (AN) 2R2CK C (±0.25pF) MCH032A (AN) 2R7CK MCH032A (AN) 030CK MCH032A (AN) 3R3CK MCH032A (AN) 3R9CK 0.6 ± 0.03 MCH032A (AN) 040CK MCH032A (AN) 4R7CK MCH032A (AN) 050CK MCH032A (AN) 5R6DK MCH032A (AN) 060DK MCH032A (AN) 6R8DK MCH032A (AN) 070DK D (±0.5pF) MCH032A (AN) 080DK MCH032A (AN) 8R2DK MCH032A (AN) 090DK MCH032A (AN) 100DK Capacitance (pF) 12 15 18 22 27 33 39 47 56 68 82 100 Temperature A AN(CG) (COG) (CH) Characteristic 25V Rated voltage (V) Product No. Tolerance Product thickness(mm) MCH032A (AN) 120JK MCH032A (AN) 150JK MCH032A (AN) 180JK MCH032A (AN) 220JK MCH032A (AN) 270JK MCH032A (AN) 330JK J (±5%) 0.6 ± 0.03 MCH032A (AN) 390JK MCH032A (AN) 470JK MCH032A (AN) 560JK MCH032A (AN) 680JK MCH032A (AN) 820JK MCH032A (AN) 101JK Rev.A 2/12 MCH03 Ceramic capacitors •High dielectric constant capacitors Capacitance (pF) 100 150 220 330 470 680 1,000 1,500 2,200 4,700 10,000 Capacitance (pF) 10,000 Temperature Rated voltage (V) Tolerance Product thickness(mm) K (±10%) 0.6 ± 0.03 CN (R) (B) (X7R) Characteristic 16V 25V Product No. Product No. MCH032CN101KK MCH032CN151KK MCH032CN221KK MCH032CN331KK MCH032CN471KK MCH032CN681KK MCH032CN102KK MCH032CN152KK MCH032CN222KK MCH033CN472KK CN (X5R) Characteristic 6.3V Product No. MCH038CN103KK Temperature FN(F) (Y5V) Characteristic 16V Rated voltage (V) Product No. Tolerance Product thickness(mm) MCH033FN103ZK Z (+80%, −20%) 0.6 ± 0.03 Rev.A 3/12 MCH03 Ceramic capacitors •Performance and test method No. Items Performance Test Method (As per JIS C 5101-1, JIS C 5101-10) 1 Appearance and dimensions No marked defects shall be allowed As per 4.4 of JIS C 5101-1. for appearance. As per 4.5 of JIS C 5101-10 Dimensions shall be as specified the Using a Magnifier. clause 4. 2 Withstanding voltage No dielectrical breakdown or other damage shall be allowed. As per 4.6 of JIS C 5101-1. As per 4.6.4 of JIS C 5101-10 Voltage shall be applied as per Table1. Table 1 CharacVoltage teristic A, AN 300% Rated voltage CN 250% Rated voltage FN Voltage shall be applied for 1 to 5s with 50mA charging and discharging curent. 3 Insulation resistance Not less than 10000MΩ or 500MΩ µF, whichever is less. (For products with rated voltage less than 16V, it is not less than 10000MΩ or 100MΩ µF, whichever is less.) As per 4.5 of JIS C 5101-1. As per 4.6.3 of JIS C 5101-10 Measurements shall be made after 60+/−5s period of the rated voltage applied. 4 Capacitance Capacitance shall be within specified tolerance range. As per 4.7 of JIS C 5101-1. As per 4.6.1 of JIS C 5101-10 Measurements shall be made under the conditions specified in Table 2. Characteristic A, AN CN FN 5 Dielectric loss tangent A, AN CN FN Capacitance < 30pF tan δ < − 100/(400+20C)% < 30pF Capacitance − tan δ < − 0.1% Table 2 Frequency Voltage < > 1000 pF − 1000 pF 1+/−0.1MHz 1+/−0.1kHz 1+/−0.1Vrms. 1+/−0.1Vrms. 1+/−0.1kHz 1+/−0.1Vrms. As per 4.8 of JIS C 5101-1. As per 4.6.2 of JIS C 5101-10 Measurements shall be made under the conditions specified in Table 2. Rated voltage=25V tan δ < − 3.0% Rated voltage=16V tan δ < − 5.0% Rated voltage=6.3V tan δ < − 10.0% Rated voltage=16V tan δ < − 10.0% Rev.A 4/12 MCH03 Ceramic capacitors No. Items 6 Temperature characteristic Performance A, AN CN FN Capacitance C < − 2pF 0+/−250ppm/°C Capacitance C=3pF 0+/−120ppm/°C Capacitance C < − 4pF 0+/−60ppm/°C (−55°C to +125°C) X7R R +/−15% (−55°C to +125°C) B +/−10% (−25°C to +85°C) X5R +/−15% (−55°C to +85°C) Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.24 of JIS C 5101-1. As per 4.7 of JIS C 5101-10 Temperature coefficient shall be calculated at 20°C and 85°C. As per 4.24 of JIS C 5101-1. As per 4.7 of JIS C 5101-10 If required, measurements shall be made at a given temperature. +30%, −80% (−25°C to +85°C) +22%, −82% (−30°C to +85°C) 7 Solderability 8 Resistance to solderin heat More than 3/4 of each end termination shall be covered with new solder. Appearance Without mechanical damage. Change rate from initial value A, AN Within +/−2.5% or +/−0.25pF whichever is larger. CN Within +/−7.5% FN Within +/−20% Dielectric loss tangent Within specified initial value. Insulation resistance Within specified initial value. Withstanding No defects shall be allowed. voltage 9 End termination adherence Without peeling or sign of peeling shall be allowed on the end terminations. As per 4.15.2 of JIS C 5101-1. As per 4.11 of JIS C 5101-10 The solder specified in JIS Z 3282 H63A shall be used. Ans the flux containing 25% rosin and ethanol solution shall be used. The specimens shall be immersed into the solder at 235+/−5°C for 2+/−0.5s So that both end terminations are completely under solder. As per 4.14 of JIS C 5101-1. As per 4.10 of JIS C 5101-10 The solder specified in JIS Z 3282. H63A shall be used. The specimens shall be immersed into the solder at 260+/−5°C for 5+/−0.5s so that both end terminations are completely under the solder. Pre-heating at 150+/−10°C for 1 to 2min Initial measurements prior to test shall be performed after the thermal Pre-conditioning specified in Remarks (1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. Table3 Characteristic A, AN CN, FN Time 24+/−2 h 48+/−4 h As per 4.13 of JIS C 5101-1. As per 4.8 ofJIS C 5101-10 A 2N weight for 10+/−1s shall be applied to the soldered specimens as shown by the arrow mark in the below sketch. Applied pressure Substrate Capacitor Rev.A 5/12 MCH03 Ceramic capacitors No. Items Performance Test Method (As per JIS C 5101-1, JIS C 5101-10) 10 Bending strength Appearance Without mechanical damage. As per 4.35 of JIS C 5101-1. As per 4.9 of JIS C 5101-10 Glass epoxy board with soldered specimens shall be bent till 1mm by 1.0mm/s. 11 Vibration Appearance Without mechanical damage. As per 4.17 of JIS C 5101-1 The specimens shall be soldered on the specified test jig. Initial measurements shall be made after the thermal pre-conditioning specified in Remarks(1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. [Condition] Directions : 2h each X, Y and Z directions Total : 6h Frequency range : 10 to 55 to 10Hz(1min) Applitude : 1.5mm (shall not exceed acceleration196m/s2) Change rate from initial value Dielectric loss tangent A, AN Capacitance shall be within specified tolerance range. CN Within +/−7.5% FN Within +/−20% Within specified initial value. Table3 Characteristic A, AN CN, FN 12 Temperature Appearance cycling Change rate from initial value Without mechanical damage. A, AN CN Rated voltage 25V,16V Rated voltage 6.3V FN Dielectric loss tangent Insulation resistance Time 24+/−2 h 48+/−4 h As per 4.16 of JIS C 5101-1 As per 4.12 of JIS C 5101-10 Within +/−2.5% or The specimens shall be soldered on the test +/−0.25pF whichever jig shown in Remarks. is larger. Temperature cycle : 5cycles Initial measurements prior to test shall be performed after the thermal Within +/−7.5% per-conditioning specified in Remarks (1). Final measurements shall be made after the Within +/−10.0% specimens have been left at room temperature as per Table3. Within +/−20% Within specified initial value. Within specified initial value. Withstanding No defects shall be allowed. voltage Test condition Step Temp. (°C) Time (min) 1 Min operating temp. 2 Room temp. 30+/−3 < −3 3 Max operating temp. 4 Room temp. 30+/−3 < −3 Table3 Characteristic A, AN CN, FN Time 24+/−2 h 48+/−4 h Rev.A 6/12 MCH03 Ceramic capacitors No. 13 Humidity (Steady) Items Performance Appearance Without mechanical damage. Change rate from initial value A, AN Rated voltage 25V,16V CN Rated voltage 6.3V FN Dielectric tangent Insulation resistance 14 Humidity life test Within +/−5.0% or +/−0.5pF whichever is larger. Within +/−12.5% Within +/−25.0% Within +/−30.0% tan δ < − 0.3% Less than 200% of CN initial spec. Less than 150% of FN initial spec. Not less than 1000MΩ or 50MΩ µF, whichever is less. (For products with rated voltage less than 16V, it is not less than 1000MΩ or 10MΩ µF, whichever is less.) Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.22 of JIS C 5101-1 JIS C 5101-10 Test temperature : 60+/−2°C Relative humidity : 90 to 95% Test time : 500 +24/−0 h Initial measurements prior to test shall be made after the voltage pre-conditioning specified in Remarks (2). Final measurements have been left at room temperature as per Table3. Table3 A, AN Characteristic A, AN CN, FN Time 24+/−2 h 48+/−4 h Appearance Without mechanical damage. Change rate from initial value Dielectric loss tangent As per 4.22 of JIS C 5101-1 As per 4.14 of JIS C 5101-10 Within +/−7.5% or A, AN Test temperature : 60+/−2°C +/−0.75pF whichever Relative humidity : 90 to 95% is larger. Voltage : Rated voltage Rated Test time : 500 +24/−0 h Within +/−12.5% voltage Initial measurements prior to test shall 25V,16V be made after the voltage CN Rated pre-conditioning specified in Within +/−25.0% voltage Remarks (2). 6.3V Final measurements shall be made after Within +/−30.0% FN the specimens have been left at room temperature as per Table3. tan δ < A, AN − 0.5% CN FN Insulation resistance Less than 200% of initial spec. Less than 150% of initial spec. Not less than 500MΩ or 25MΩ µF, whichever is less. (For products with rated voltage less than 16V, it is not less than 500mΩ or 5MΩ µF, whichever is less.) Table3 Characteristic A, AN CN, FN Time 24+/−2 h 48+/−4 h Rev.A 7/12 MCH03 Ceramic capacitors No. Items 15 Heat life test Performance Appearance Without mechanical damage. Change rate from initial value A, AN CN Dielectric loss tangent Insulation resistance Rated voltage 25V,16V Rated voltage 6.3V Within +/−3.0% or +/−0.3pF whichever is larger. Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.23 of JIS C 5101-1. As per 4.15 of JIS C 5101-10 Test Voltage temperature(°C) Within +/−15.0% A, AN 125 CN 85 (B, X5R) Within +/−25.0% FN Within +/−30.0% A, AN tan δ < − 0.3% CN Less than 200% of initial spec. FN Less than 150% of initial spec. Not less than 1000MΩ or 50MΩ µF, whichever is less. (For products with rated voltage less than 16V, it is not less than 1000mΩ or 10MΩ µF, whichever is less.) 125 (R, X7R) FN 85 200% Rated voltage 200% Rated voltage 200% Rated voltage 200% Rated voltage Test time (h) 1000 +48/−0 1000 +48/−0 1000 +48/−0 Initial measurements prior to test shall be made after the voltage pre-conditioning specified in Remarks (2). Final measurements shall be made after the specimens have been left at room temperature Table3 Characteristic A, AN CN, FN Time 24+/−2 h 48+/−4 h [Remarks] Pre-conditioning If specified in test method of as per 3(Performance and test merhod), capacitors of CN, FN characteristics shall be pre-conditionded as follows. (1) Thermal pre-conditioning Prior to initial measurements, specimens shall be conditioned at a temperature of 150 0/−10°C for a period of 1hr., and shall be allowed to stabilize at room temperature for 48+/−4h (2) Voltage pre-conditioning Prior to initial measurements, voltage specified as a test condition shall be applied to specimens for a period of 1hr., and the specimens shall be allowed to stabilize at room temperature for 48+/−4h <Test jig> Soldering Glass epoxy substrate Rev.A 8/12 MCH03 Ceramic capacitors zPackaging specifications Taping dimensions Reel dimensions t φJ d E +1.0 9.0 −0 Pulling direction A D G H +0 φ180 −1.5 φ13.0 + − 0.2 t1 F φ60.0+1.0 −0 C B Pulling direction C Symbol D E F G H d J t t1 0.37 0.42 0.5 8.0 3.5 1.75 2.0 2.0 4.0 φ1.5 Dimensions +/ −0.2 +/ −0.05 +/ −0.1 +/ −0.05 +/ −0.05 +/ −0.1 +0.1/ −0 +/ −0.02 +/ −0.02 MAX. Symbol Style MCH03 A B 0.37 +/ −0.03 0.67 +/ −0.03 (Unit : mm) Label pasting As per EIAJ ET−7200A (Unit : mm) (Unit : mm) (1) The quantity for one reel is as bellows. Kind of reel φ180 reel Series Paper tape Quantity MCH03 15,000 pcs. Symbol K (2) When the tape is pulled out towards the operator with the cover tape facing upward, the feeding holes shall be found on the right portion of the tape. (3) Specification of beginning and ending of the tape are as follows. Ending(reel's center) Beginning(reel's round) : Approx. 300mm (no chips) : Approx. 270mm (no chips) : Approx. 30mm (no pasted tape) : Approx. 260mm (cover tape only) (4) No juncture of tape shall be allowed. (5) The share strength of tape shall be more than 5N at the break down strength. (6) The peel strength of the cover tape shall be 0.1 to 0.7(N) when the cover tape are peeled 0 to 15° degree from the surface. (7) The number of missing components shall not exceed 0.1% of the total number of components (marked number) or one whichever is the larger, and no consecutive missing exceeding two is allowed. (8) The reels made from resin shall be used, as per EIAJ ET-7200A. zMarking No marking shall be performed on the chip. Trademark, parts number, quantity, lot No. , and country of origin shall be labeled on each reel, bulk case. zNumbering system for LOT No. Example 03 (1) 01 (2) A0001 (3) J (4) (1) The end of the Christian Era < two digits> of production finish. (2) Week in completing part of production finish. (3) Manufacture continuity number. (4) The symbol of manufacturing plant. Rev.A 9/12 MCH03 Ceramic capacitors zLabel expression The Figure below is label expression < Label Example > Part Number : MCH032A470JK ④ ① MCH032A470JK ② ③ □ 15,000pcs 0501 00001Ｆ ⑤ 0123456789ABCDEFGHI J0123456789ABCDEFGHI J ＪＡＰＡＮ ⑦ Ｋ．ＳＡＴＯ Excellence ｉｎ Ｅｌｅｃｔｒｏｎｉｃｓ ROHM ⑧ ⑥ ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ Part Number Division cord Quantity Lot No. The Country of origin Inspector QR code Trademark Rev.A 10/12 MCH03 Ceramic capacitors zPacking method 1) φ180mm Reel EIAJ cole B' 2 C' (reel) Label A' [width of 9mm : 5reel] 1 A (interior box of R-26) Packing slip B C (R-26) < Packaging unit > Symbol Dimensions K R-26 Quantity of reel in interior box Quantity of reel in box of R-26 5 20 Packaging interior box of R-26 A (A’) 195 185 B (B’) 255 60 C (C’) 190 185 (Unit : mm) < Appearance > Carton < Accumulation > You must do accumulation by ten boxes < Packaging slip > 1. 2. 3. 4. 5. Customer Parts number Quantity Box quantity Trade mark zWeight / Piece (Unit : mg) Size Item Thickness 0603 (0201) MCH03 0.3mm Characteristic Weight / Piece A, AN 0.3 CN 0.3 FN 0.3 (Note) The measured values in the table are for reference only. Actual weight of these chips may very slightly lot by lot. Rev.A 11/12 MCH03 Ceramic capacitors zElectrical characteristics gA (C0G) Characteristics 1000000 RATE OF CAPACITANCE CHANGE : (%) 5 4 100000 3 10000 2 1 1000 IMPEDANCE (Ω) 0 −1 −2 −3 −4 −5 −50 0 50 0.5pF 100 10pF 10 1 0.1 100 1 10 100 1000 10000 TEMPERATURE (°C) FREQUENCY (MHz) Fig.1 Capacitance-temperature characteristics Fig.2 Impedance-frequency characteristics gCN (X7R) Characteristics 1000000 20 100000 10 0 10000 −10 −20 10 5 −80 −40 0 40 80 120 1000 IMPEDANCE (Ω) −30 Dissipation factor (%) CAPACITANCE CHANGE : (%) 30 100 10 0.1 160 1000pF 1 1 10 100 1000 10000 FREQUENCY (MHz) TEMPERATURE : (°C) Fig.4 Impedance-frequency characteristics Fig.3 Capacitance-temperature characteristics 20 10 0 −10 −20 −30 −40 −50 −60 −70 −80 60 50 40 30 20 10 −80 −40 0 40 80 120 Dissipation factor (%) CAPACITANCE CHANGE : (%) gFN (Y5V) Characteristics 160 TEMPERATURE : (°C) Fig.5 Capacitance-temperature characteristics Rev.A 12/12 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1