AZF-60 SERIES AC/DC Power Module 60W FEATURES ►Fully encapsulated Plastic Case ►3 Mounting Versions: - PCB Mounting with Solder Pins - Chassis Mounting with Screw Terminals - DIN-Rail Mounting ►Universal Input 85-264 VAC, 47- 440 Hz ►Protection Class ll ►Safety Approval to cUL/UL/IEC/EN 60950-1 ►UL508 Approval (Option) ►Over Load and Over Voltage Protection ►3 Year Product Warranty PRODUCT OVERVIEW The MINMAX AZF-60 series is a new range of fully encapsulated AC/DC power supply modules. The product features EMI-filter to EN55022, class B and EMS compliance to EN 61000-4 standard.Universal input voltage 85-264VAC and International safety approvals qualifies these power modules for applications in products with worldwide markets. For industrial applications, the models for chassis mounting can also be supplied as option with UL508 approval.The AZF-60 series provide a cost effective solution for many space critical applications in commercial and industrial electronic equipment. Model Selection Guide Model Number PCB Mounting (For model with Chassis Mounting, add suffix C) Output Voltage Output Current Input Current µF Efficiency (typ.) @Max. Load % 50 8000 79 1060 50 3900 82 4000 1047 50 3300 83 24 2500 1035 50 1500 84 AZF-60S36 36 1666 1035 50 1000 84 AZF-60S48 48 1250 1035 50 680 84 VDC Max. mA AZF-60S051 5.1 10,000 936 AZF-60S12 12 5000 AZF-60S15 15 AZF-60S24 Input Specifications Parameter Model Input Voltage Range All Models Input Frequency Range Input Voltage Range 115VAC Inrush Current (Cold Start at 25℃) E-mail:[email protected] 2013/02/25 REV:11 230VAC Tel:886-6-2923150 Page 1 of 4 Max. capacitive Load 115VAC, 60Hz @Max. Load @No Load mA(typ.) mA(typ.) Min. Typ. 47 --- 85 120 --- --- --- Max. Unit 264 VAC --- 370 VDC --- 50 A --- 63 30 Hz A AZF-60 SERIES AC/DC POWER MODULE 60W Output Specifications Parameter Output Voltage Accuracy Line Regulation Load Regulation Conditions Vin=Min. to Max. Iout=Min. to Max. 5.1VDC Output Models Other Output Models Ripple & Noise (20MHz) Minimum Load Over Voltage Protection Transient Response Deviation Temperature Coefficient Overshoot Zener diode clamp (Iout=100% to Iout=50%) Short Circuit Protection General Specifications Parameter I/O Isolation Voltage I/O Isolation Resistance Switching Frequency Hold-up Time MTBF (calculated) EMC Emission Conditions Input to Output, 60 Seconds 500 VDC MIL-HDBK-217F@25℃, Ground Benign Conducted and radiated Standard EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EMC Immunity according EN61000-6-1 EN61000-4-6 EN61000-4-8 EN61000-4-11 Protection Class II Safety Approvals Input Fuse Environmental Specifications Parameter Temperature Range (operational) Power Derating Power Derating (5.1Vout) Storage Temperature Range Over Temperature Protection Cooling Humidity (non condensing) 4 5 6 Ambient +50℃ to +70℃ +40℃ to +70℃ Typ. ±1.0 ±0.2 ±0.5 2.0 1.0 10 120 ±3 ±0.02 ----- Max. ±2.0 ±1.0 ±1.0 3.0 1.3 ----±6 --5 --- Unit % % % %VPP of Vo %VPP of Vo %Inom. % of Vo % %/℃ % Vout %Inom. Min. Typ. Max. Unit 3000 ----VACrms 100 ----MΩ --100 --KHz --20 --ms 125,000 ----Hours EN 55011 class B, EN 55022 class B, FCC part 15 class B Specification Requirement Performance Criteria B Air ±8KV Cont. ±4KV A 80~1000MHz, 10V/m 80% AM, 1KHz modulation B AC port ±2KV DC, SL, TL ±2KV not less than 1 min. B 1.2/50µS(8/20µS) AC dif. ±1KV DC ±0.5KV 0.15~80MHz, 10Vrms (functional earth ports included) B 80% AM, 1KHz modulation A 50Hz/60Hz, 30A/m B 30%, 10ms C 60%, 100ms, 95%, 5000ms According IEC/EN 60536 cUL/UL 60950-1,IEC/EN 60950-1 (UL508 for models with order code suffix ICE only) All Models Built-in Fuse External Fuse (Recommended) 1 2 3 ----- Foldback, auto-recovery 105 (long term overload condition may cause damage) Hiccup mode, indefinite (automatic recovery) Current Limitation Notes Min. --------------- 6A / 250VAC 3A Slow – Blow Type Conditions -10℃ -40℃ at 90℃ (automatic recovery at 67℃) Free-Air convection --- +70℃ 2.25W / ℃ 2.25W / ℃ +85℃ 95 % rel. H All specifications typical at Ta=+25℃, resistive load, 115VAC, 60Hz input voltage and after warm-up time rated output current unless otherwise noted. Ripple & Noise measurement bandwidth is 0~20 MHz These power modules require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage the power supplies however they may not meet all listed specifications. Other input and output voltage may be available, please contact factory. Long term short circuit operation may cause damage to the unit. Specifications are subject to change without notice E-mail:[email protected] 2013/02/25 REV:11 Tel:886-6-2923150 Page 2 of 4 AZF-60 SERIES AC/DC POWER MODULE 60W Package Specifications PCB Mounting Mechanical Dimensions Pin Connections Pin 25.4 [1.00] 4 81.3 [3.20] 27.5 [1.08] 31.45 [1.24] Mounting M4.0 Thread Bottom View 2 AC(N) – AC Neutral 4 +Vout AC(L) – AC Line 6 -Vout 88.9 [3.50] 28.75 [1.13] 1 2 1.0 [ 0.04] 6 Function 1 55.88 [2.20] ►All dimensions in mm (inches) 0.7 [0.03] 6.0 [0.24] 67.5 [2.66] 34.2 [1.35] ►Tolerance: ±0.5 (±0.02) ►Pin diameter — 1.0 ±0.1 (0.04±0.004) Physical Characteristics Case Size : 88.9x67.5x34.2mm (3.50x2.66x1.35 inches) Pin Material : Copper Alloy with Gold Plate Over Nickel Subplate Case Material Plastic resin + Fiberglass (flammability to UL 94V-0 rated) : Weight : 345g Package Specifications Chassis Mounting (order code suffix C) Mechanical Dimensions Connections Terminal 4x 3.5 1 2 Top View 4 1 DCON 100.0 [3.94] 112.0x67.8x38.0mm (4.41x2.67x1.50 inches) Plastic resin + Fiberglass (flammability to UL 94V-0 rated) 357g E-mail:[email protected] 2013/02/25 REV:11 Tel:886-6-2923150 Page 3 of 4 38.0 [1.50] 5.0[0.20] Physical Characteristics : : -Vout NC 11.0 [0.43] 16.8 [0.66] 90.0 [3.54] : 6 NC NC: No Connection 112.0 [4.41] Case Material Weight +Vout 7 POWER"GOOD"INDICATOR Case Size NC 4 5 3 Indication LED AC(L) – AC Line 3 67.8 [2.67] 2 5 50.0 [1.97] 7 6 Function AC(N) – AC Neutral ►All dimensions in mm (inches) ►Tolerance: ±0.5 (±0.02) AZF-60 SERIES AC/DC POWER MODULE 60W Package Specifications with DIN Rail Mounting Bracket (order code AC-DIN-02) Mechanical Dimensions 4x 3.5 2 5 Top View 4 1 67.8 [2.67] 50.0 [1.97] 7 6 3 Indication LED DCON POWER"GOOD"INDICATOR 100.0 [3.94] 112.0 [4.41] 38.0 [1.50] 11.0 [0.43] 3.0 [0.12] 5.0[0.20] 11.0 [0.43] 16.8 [0.66] 90.0 [3.54] Physical Characteristics Case Size : 112.0x67.8x38.0mm (4.41x2.67x1.50 inches) Weight : 410g Case Material : Plastic resin + Fiberglass (flammability to UL 94V-0 rated) DIN-Rail Mounting Kit Minmax Technology Co., Ltd. 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] 2013/02/25 REV:11 Page 4 of 4