LINER LT3070 5a, low noise, programmable output, 85mv dropout linear regulator Datasheet

LT3070
5A, Low Noise,
Programmable Output,
85mV Dropout
Linear Regulator
Features
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
Description
Output Current: 5A
Dropout Voltage: 85mV Typical
Digitally Programmable VOUT : 0.8V to 1.8V
Digital Output Margining: ±1%, ±3% or ±5%
Low Output Noise: 25µVRMS (10Hz to 100kHz)
Parallel Multiple Devices for 10A or More
Precision Current Limit: ±20%
±1% Accuracy Over Line, Load and Temperature
Stable with Low ESR Ceramic Output Capacitors
(15µF Minimum)
High Frequency PSRR: 30dB at 1MHz
Enable Function Turns Output On/Off
VIOC Pin Controls Buck Converter to Maintain Low
Power Dissipation and Optimize Efficiency
PWRGD/UVLO/Thermal Shutdown Flag
Current Limit with Foldback Protection
Thermal Shutdown
28-Lead (4mm × 5mm × 0.75mm) QFN Package
Applications
n
n
n
n
FPGA and DSP Supplies
ASIC and Microprocessor Supplies
Servers and Storage Devices
Post Buck Regulation and Supply Isolation
The LT®3070 is a low voltage, UltraFast™ transient response linear regulator. The device supplies up to 5A of
output current with a typical dropout voltage of 85mV.
A 0.01µF reference bypass capacitor decreases output
voltage noise to 25µVRMS. The LT3070’s high bandwidth
permits the use of low ESR ceramic capacitors, saving
bulk capacitance and cost. The LT3070’s features make
it ideal for high performance FPGAs, microprocessors or
sensitive communication supply applications.
Output voltage is digitally selectable in 50mV increments
over a 0.8V to 1.8V range. A margining function allows
the user to adjust system output voltage in increments of
±1%, ±3% or ±5%. The IC incorporates a unique tracking
function to control a buck regulator powering the LT3070’s
input. This tracking function drives the buck regulator to
maintain the LT3070’s input voltage to VOUT + 300mV,
minimizing power dissipation.
Internal protection includes UVLO, reverse-current protection, precision current limiting with power foldback and
thermal shutdown. The LT3070 regulator is available in a
thermally enhanced 28-lead, 4mm × 5mm QFN package.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
UltraFast and VLDO are trademarks of Linear Technology Corporation. All other trademarks are
the property of their respective owners. Patents pending.
Typical Application
Dropout Voltage
0.9V, 5A Regulator
VIN
1.2V
50k
150
2.2µF
IN
330µF
BIAS
PWRGD
EN
VO0
SENSE
LT3070
OUT
VO1
VO2
MARGSEL
2.2µF*
1nF
REF/BYP
GND
4.7µF*
*X5R OR X7R CAPACITORS
MARGTOL
VIOC
VIN = VOUT(NOMINAL)
PWRGD
0.01µF
3070 TA01a
VOUT
0.9V
5A
10µF*
DROPOUT VOLTAGE (mV)
VBIAS
2.2V TO 3.6V
120
90
VOUT = 1.8V
VBIAS = 3.3V
60
VOUT = 0.8V
VBIAS = 2.5V
30
0
0
1
3
4
2
OUTPUT CURRENT (A)
5
3070 TA01b
3070fa
LT3070
Pin Configuration
IN, OUT...................................................... –0.3V to 3.3V
BIAS.............................................................. –0.3V to 4V
VO2, VO1, VO0 Inputs..................................... –0.3V to 4V
MARGSEL, MARGTOL Input......................... –0.3V to 4V
EN Input........................................................ –0.3V to 4V
SENSE Input................................................. –0.3V to 4V
VIOC, PWRGD Outputs................................. –0.3V to 4V
REF/BYP Output............................................ –0.3V to 4V
Output Short-Circuit Duration……...................Indefinite
Operating Junction Temperature (Note 2)
LT3070E/LT3070I.............................. –40°C to 125°C
LT3070MP.......................................... –55°C to 125°C
Storage Temperature Range................... –65°C to 150°C
VO0
VO1
VO2
GND
BIAS
EN
TOP VIEW
28 27 26 25 24 23
VIOC 1
22 MARGTOL
PWRGD 2
21 MARGSEL
REF/BYP 3
20 GND
GND 4
19 SENSE
29
GND
IN 5
18 OUT
IN 6
17 OUT
IN 7
16 OUT
IN 8
15 OUT
GND
GND
GND
GND
9 10 11 12 13 14
GND
(Note 1)
GND
Absolute Maximum Ratings
UFD PACKAGE
28-LEAD (4mm s 5mm) PLASTIC QFN
TJMAX = 125°C, θJA = 30°C/W TO 35°C/W
EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3070EUFD#PBF
LT3070EUFD#TRPBF
3070
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3070IUFD#PBF
LT3070IUFD#TRPBF
3070
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3070MPUFD#PBF
LT3070MPUFD#TRPBF
3070
28-Lead (4mm × 5mm) Plastic QFN
–55°C to 125°C
LEAD BASED FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT3070EUFD
LT3070EUFD#TR
3070
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3070IUFD
LT3070IUFD#TR
3070
28-Lead (4mm × 5mm) Plastic QFN
–40°C to 125°C
LT3070MPUFD
LT3070MPUFD#TR
3070
28-Lead (4mm × 5mm) Plastic QFN
–55°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3070fa
LT3070
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. COUT = 15µF (Note 9), VIN = VOUT + 0.3V (Note 5), VBIAS = 2.5V unless
otherwise noted.
PARAMETER
CONDITIONS
IN Pin Voltage Range
VIN ≥ VOUT + 150mV, IOUT= 5A
MIN
l
TYP
0.95
2.2
UNITS
3.0
V
3.6
V
Regulated Output Voltage
VOUT = 0.8V, 10mA ≤ IOUT ≤ 5A, 1.05V ≤ VIN ≤ 1.25V
VOUT = 0.9V, 10mA ≤ IOUT ≤ 5A, 1.15V ≤ VIN ≤ 1.35V
VOUT = 1V, 10mA ≤ IOUT ≤ 5A, 1.25V ≤ VIN ≤ 1.45V
VOUT = 1.1V, 10mA ≤ IOUT ≤ 5A, 1.35V ≤ VIN ≤ 1.55V
VOUT = 1.2V, 10mA ≤ IOUT ≤ 5A, 1.45V ≤ VIN ≤ 1.65V, VBIAS = 3.3V
VOUT = 1.5V, 10mA ≤ IOUT ≤ 5A, 1.75V ≤ VIN ≤ 1.95V, VBIAS = 3.3V
VOUT = 1.8V, 10mA ≤ IOUT ≤ 5A, 2.05V ≤ VIN ≤ 2.25V, VBIAS = 3.3V
l
l
l
l
l
l
l
0.792
0.891
0.990
1.089
1.188
1.485
1.782
0.800
0.900
1.000
1.100
1.200
1.500
1.800
0.808
0.909
1.010
1.111
1.212
1.515
1.818
V
V
V
V
V
V
V
Regulated Output Voltage Margining
(Note 3)
MARGTOL = 0V, MARGSEL = VBIAS
MARGTOL = 0V, MARGSEL = 0V, IOUT = 10mA
l
l
0.8
–1.2
1
–1
1.2
–0.8
%
%
MARGTOL = FLOAT, MARGSEL = VBIAS
MARGTOL = FLOAT, MARGSEL = 0V, IOUT = 10mA
l
l
2.7
–3.3
3
–3
3.3
–2.7
%
%
MARGTOL = VBIAS, MARGSEL= VBIAS
MARGTOL = VBIAS, MARGSEL = 0V, IOUT = 10mA
l
l
4.6
–5.4
5
–5
5.4
–4.6
%
%
Line Regulation to VIN
VOUT = 0.8V, ∆VIN = 1.05V to 2.7V, VBIAS = 3.3V, IOUT = 10mA
VOUT = 1.8V, ∆VIN = 2.05V to 2.7V, VBIAS = 3.3V, IOUT = 10mA
l
l
1.0
1.0
mV
mV
Line Regulation to VBIAS
VOUT = 0.8V, ∆VBIAS = 2.2V to 3.6V, VIN = 1.1V, IOUT = 10mA
VOUT = 1.8V, ∆VBIAS = 3.25V to 3.6V, VIN = 2.1V, IOUT = 10mA
l
l
2.0
1.0
mV
mV
Load Regulation,
∆IOUT = 10mA to 5A
VBIAS = 2.5V, VIN = 1.05V, VOUT = 0.8V
–1.5
–3.0
–5.5
mV
mV
–2
–4.0
–7.5
mV
mV
–2
–4.0
–7.5
mV
mV
–2.5
–5.0
–9.0
mV
mV
–3
–7.0
–13
mV
mV
20
35
mV
50
65
85
mV
mV
85
120
150
mV
mV
BIAS Pin Voltage Range (Note 3)
l
MAX
l
VBIAS = 2.5V, VIN = 1.25V, VOUT = 1.0V
l
VBIAS = 3.3V, VIN = 1.45V, VOUT = 1.2V
l
VBIAS = 3.3V, VIN = 1.75V, VOUT = 1.5V
l
VBIAS = 3.3V, VIN = 2.05V, VOUT = 1.8V
l
Dropout Voltage,
VIN = VOUT(NOMINAL) (Note 6)
IOUT = 1A, VOUT = 1V
l
IOUT = 2.5A, VOUT = 1V
l
IOUT = 5A, VOUT = 1V
l
SENSE Pin Current
VIN = 1.1V, VSENSE = 0.8V
VBIAS = 3.3V, VIN = 2.1V, VSENSE = 1.8V
l
l
35
200
50
300
65
400
µA
µA
Ground Pin Current,
VIN = 1.3V, VOUT = 1V
IOUT = 10mA
IOUT = 5A
l
l
0.65
0.9
1.1
1.35
1.8
2.3
mA
mA
3070fa
LT3070
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. COUT = 15µF (Note 9), VIN = VOUT + 0.3V (Note 5), VBIAS = 2.5V unless
otherwise noted.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
BIAS Pin Current in Nap Mode
EN = Low (After POR Completed)
l
120
200
320
µA
BIAS Pin Current,
VIN = 1.3V, VOUT = 1V
IOUT = 10mA
IOUT = 100mA
IOUT = 500mA
IOUT = 1A
IOUT = 2.5A
IOUT = 5A
l
l
l
l
l
l
0.75
1.25
2.0
2.6
3.5
4.5
1.08
1.8
3.0
3.8
5.2
6.9
1.5
2.4
4.0
5.0
7.0
10.0
mA
mA
mA
mA
mA
mA
Current Limit (Note 5)
VIN – VOUT < 0.3V, VBIAS = 3.3V
VIN – VOUT = 1.0V, VBIAS = 3.3V
VIN – VOUT = 1.7V, VBIAS = 3.3V
l
l
l
5.1
3.2
1.2
6.4
4.5
2.5
7.7
5.8
4.3
A
A
A
Reverse Output Current (Note 8)
VIN = 0V, VOUT = 1.8V
l
300
450
µA
PWRGD VOUT Threshold
Percentage of VOUT(NOMINAL), VOUT Rising
Percentage of VOUT(NOMINAL), VOUT Falling
l
l
90
85
93
88
%
%
PWRGD VOL
IPWRGD = 200µA (Fault Condition)
l
50
150
mV
VBIAS Undervoltage Lockout
VBIAS Rising
VBIAS Falling
l
l
1.1
0.9
1.55
1.4
2.1
1.7
V
V
VIN-VOUT Servo Voltage by VIOC
87
82
l
250
300
350
mV
VIOC Output Current
VIN = VOUT(NOMINAL) + 150mV, Sourcing Out of the Pin
VIN = VOUT(NOMINAL) + 450mV, Sinking Into the Pin
l
l
160
170
235
255
310
340
µA
µA
VIL Input Threshold (Logic-0 State),
VO2, VO1, VO0, MARGSEL, MARGTOL
Input Falling
l
0.25
V
VBIAS – 0.9
V
VIZ Input Range (Logic-Z State),
VO2, VO1, VO0, MARGSEL, MARGTOL
VIH Input Threshold (Logic-1 State),
VO2, VO1, VO0, MARGSEL, MARGTOL
Input Rising
l
0.75
l
VBIAS – 0.25
Input Hysteresis (Both Thresholds),
VO2, VO1, VO0, MARGSEL, MARGTOL
V
60
mV
Input Current High,
VO2, VO1, VO0, MARGSEL, MARGTOL
VIH = VBIAS = 2.5V, Current Flows Into Pin
l
25
40
µA
Input Current Low,
VO2, VO1, VO0, MARGSEL, MARGTOL
VIL = 0V, VBIAS = 2.5V, Current Flows Out of Pin
l
25
40
µA
EN Pin Threshold
VOUT = Off to On
VOUT = On to Off
l
l
0.9
1.4
V
V
EN Pin Logic High Current
VEN = VBIAS = 2.5V
l
2.5
6.5
µA
EN Pin Logic Low Current
VEN = 0V
l
0.1
µA
4.0
3070fa
LT3070
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. COUT = 15µF (Note 9), VIN = VOUT + 0.3V (Note 5), VBIAS = 2.5V unless
otherwise noted.
PARAMETER
CONDITIONS
VBIAS Ripple Rejection
VBIAS = VOUT + 1.5VAVG, VRIPPLE =0.5VP-P , fRIPPLE = 120Hz,
VIN – VOUT = 300mV, IOUT = 2.5A
75
dB
VIN Ripple Rejection
(Notes 3, 4, 5)
VBIAS = 2.5V, VRIPPLE = 50mVP-P , fRIPPLE = 120Hz,
VIN – VOUT = 300mV, IOUT = 2.5A
66
dB
Reference Voltage Noise
(REF/BYP Pin)
CREF/BYP = 10nF, BW = 10Hz to 100kHz
10
µVRMS
Output Voltage Noise
VOUT = 1V, IOUT = 5A, CREF/BYP = 10nF, COUT = 15µF,
BW = 10Hz to 100kHz
25
µVRMS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3070 regulators are tested and specified under pulse load
conditions such that TJ ≅ TA. The LT3070E is 100% tested at TA = 25°C.
Performance at –40°C and 125°C is assured by design, characterization
and correlation with statistical process controls. The LT3070I is
guaranteed over the –40°C to 125°C operating junction temperature range.
The LT3070MP is 100% tested and guaranteed over the –55°C to 125°C
operating junction temperature range.
Note 3: To maintain proper performance and regulation, the BIAS supply
voltage must be higher than the IN supply voltage. For a given VOUT , the
BIAS voltage must satisfy the following conditions: 2.2V ≤ VBIAS ≤ 3.6V
and VBIAS ≥ (1.25 • VOUT + 1V). For VOUT ≤ 0.95V, the minimum BIAS
voltage is limited to 2.2V.
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification does not apply
for all possible combinations of input voltage and output current. When
operating at maximum output current, limit the input voltage range to
VIN < VOUT + 500mV.
MIN
TYP
MAX
UNITS
Note 5: The LT3070 incorporates safe operating area protection circuitry.
Current limit decreases as the VIN-VOUT voltage increases. Current limit
foldback starts at VIN – VOUT > 500mV. See the Typical Performance
Characteristics for a graph of Current Limit vs VIN – VOUT voltage. The
current limit foldback feature is independent of the thermal shutdown
circuity.
Note 6: Dropout voltage, VDO, is the minimum input to output voltage
differential at a specified output current. In dropout, the output voltage
equals VIN – VDO.
Note 7: GND pin current is tested with VIN = VOUT(NOMINAL) + 300mV and a
current source load. VIOC is a buffered output determined by the value of
VOUT as programmed by the VO2-VO0 pins. VIOC’s output is independent of
the margining function.
Note 8: Reverse output current is tested with the IN pins grounded and the
OUT + SENSE pins forced to the rated output voltage. This is measured as
current into the OUT + SENSE pins.
Note 9: Frequency Compensation: The LT3070 must be frequency
compensated at its OUT pins with a minimum COUT of 15µF configured
as a cluster of (15×) 1µF ceramic capacitors or as a graduated cluster
of 10µF/4.7µF/2.2µF ceramic capacitors of the same case size. Linear
Technology only recommends X5R or X7R dielectric capacitors.
3070fa
LT3070
Typical Performance Characteristics
Dropout Voltage vs Temperature
30
VIN = VOUT(NOMINAL)
TJ = 25°C
25
120
VOUT = 1.8V
VBIAS = 3.3V
60
VOUT = 0.8V
VBIAS = 2.5V
30
0
VIN = VOUT(NOMINAL)
IOUT = 1A
20
15
10
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
VOUT = 1.2V, VBIAS = 3.3V
5
0
1
3
4
2
OUTPUT CURRENT (A)
90
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
5
Dropout Voltage vs Temperature
60
30
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
VOUT = 1.2V, VBIAS = 3.3V
30
20
0.808
160
140
120
100
80
60
40
0
OUT = 1.8V
OUT = 1.5V
OUT = 0.8V
2.2
2.4
2.6 2.8 3.0
3.2
BIAS VOLTAGE (V)
3.4
1.212
ILOAD = 10mA
0.802
0.800
0.798
0.796
0.794
0.792
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3.6
3070 G06
Output Voltage (1.5V)
vs Temperature
1.515
ILOAD = 10mA
1.208
OUTPUT VOLTAGE (V)
1.006
1.002
1.000
0.998
0.996
0.994
ILOAD = 10mA
0.804
Output Voltage (1.2V)
vs Temperature
1.004
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
VOUT = 1.2V, VBIAS = 3.3V
3070 G05
Output Voltage (1V)
vs Temperature
OUTPUT VOLTAGE (V)
40
0.806
3070 G04
1.008
50
Output Voltage (0.8V)
vs Temperature
Dropout Voltage vs VBIAS
20
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
1.010
60
3070 G03
OUTPUT VOLTAGE (V)
90
70
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
IOUT = 5A
180 TJ = 25°C
DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
200
VIN = VOUT(NOMINAL)
IOUT = 5A
120
80
3070 G02
3070 G01
150
VIN = VOUT(NOMINAL)
IOUT = 2.5A
10
ILOAD = 10mA
1.510
OUTPUT VOLTAGE (V)
90
Dropout Voltage vs Temperature
100
DROPOUT VOLTAGE (mV)
Dropout Voltage vs IOUT
DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
150
1.204
1.200
1.196
1.505
1.500
1.495
1.192
1.490
1.188
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
1.485
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
0.992
0.990
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3070 G07
3070 G08
3070 G09
3070fa
LT3070
Typical Performance Characteristics
Output Voltage (1.8V)
vs Temperature
GND PIN CURRENT (mA)
OUTPUT VOLTAGE (V)
1.806
1.802
1.798
1.794
1.790
2.0
1.5
1.0
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 1.2V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
0.5
1.786
1.782
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
0
0
1
10
250
200
150
100
50
2.5
8
7
VOUT = 1.8V
VBIAS = 3.3V
6
5
4
VOUT = 0.8V
VBIAS = 2.5V
3
2
0
0
1
3
4
2
OUTPUT CURRENT (A)
EN Pin Thresholds
VBIAS = 2.5V
PWRGD TRESHOLD VOLTAGE (V)
ENABLE PIN THRESHOLD (V)
VBIAS RISING
1.5
1.0
VBIAS FALLING
0.5
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
5
3070 G15
PWRGD Threshold Voltage
1.00
1.6
0.8
2.0
3070 G14
3070 G13
1.0
3070 G12
1
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
1.2
594
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
BIAS Pin Undervoltage Lockout
Threshold
VIN = VOUT + 300mV
TJ = 25°C
9
BIAS PIN CURRENT (mA)
BIAS PIN CURRENT (µA)
VBIAS = 2.5V
350 VEN = 0V
1.4
598
BIAS Pin Current vs IOUT
400
1.8
600
3070 G11
BIAS Pin Current in Nap Mode
2.0
602
596
5
2
3
4
OUTPUT CURRENT (A)
3070 G10
300
CREF/BYP = 0.01µF
604
REF/BYP VOLTAGE (mV)
2.5
1.810
606
VIN = VOUT + 300mV
TJ = 25°C
UVLO THRESHOLD VOLTAGE (V)
1.814
3.0
ILOAD = 10mA
EN PIN RISING
EN PIN FALLING
0.6
0.4
100
VBIAS = 2.5V
VOUT = 1V
PWRGD VOL VOLTAGE (mV)
1.818
REF/BYP Pin Voltage
vs Temperature
GND Pin Current vs IOUT
0.95
VOUT RISING
0.90
0.85
VOUT FALLING
PWRGD VOL vs Temperature
VBIAS = 2.5V
IPWRGD = 200µA
80
60
40
20
0.2
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3070 G16
0.80
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3070 G17
0
–75 –50 –25
0 25 50 75 100 125 150
TEMPERATURE (°C)
3070 G50
3070fa
LT3070
Typical Performance Characteristics
Logic Input Threshold Voltages
Logic Low to Hi-Z State Transitions
0.7
0.5
INPUT FALLING
LOGIC Hi-Z TO LOW
0.4
0.3
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
2.9
2.8
INPUT RISING
LOGIC Hi-Z TO HIGH
2.7
INPUT FALLING
LOGIC HIGH TO Hi-Z
2.6
3070 G18
4.0
3.5
3.0
2.5
2.0
1.5
3070 G16
SENSE Pin Current
65
40
VLOGIC = VBIAS = 2.5V
CURRENT FLOWS INTO THE PIN
30
25
20
15
10
5
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
VBIAS = 2.5V
35 VLOGIC = 0V
CURRENT FLOWS OUT OF THE PIN
30
25
20
15
10
VBIAS = 2.5V
60 VOUT = 0.8V
CURRENT FLOWS INTO SENSE
55
50
45
40
35
5
30
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
25
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3070 G21
3070 G23
3070 G22
SENSE Pin Current
Current Limit vs Temperature
400
7.50
VBIAS = 3.3V
375 VOUT = 1.8V
CURRENT FLOWS INTO SENSE
350
7.25
Current Limit vs VIN – VOUT
8
VIN – VOUT(NOMINAL) = 300mV
300
275
250
6.75
6.50
6.25
6.00
5.75
5.50
225
5.25
200
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3070 G24
CURRENT LIMIT (A)
325
VBIAS = 3.3V
TJ = 25°C
7
7.00
CURRENT LIMIT (A)
SENSE PIN CURRENT (µA)
4.5
Logic Pin Input Current,
Low State
LOGIC PIN INPUT CURRENT (µA)
LOGIC PIN INPUT CURRENT (µA)
35
5.0
3070 G19
Logic Pin Input Current,
High State
40
VEN = VBIAS = 2.5V
5.5
1.0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
2.5
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
SENSE PIN CURRENT (µA)
0.6
INPUT RISING
LOGIC LOW TO Hi-Z
VBIAS = 3.3V
LOGIC Hi-Z TO HIGH THRESHOLD IS
RELATIVE TO VBIAS VOLTAGE
SEE APPLICATIONS INFORMATION
FOR MORE DETAILS
EN Pin Logic High Current
6.0
EN PIN LOGIC HIGH CURRENT (µA)
3.0
SEE APPLICATIONS INFORMATION
FOR MORE DETAILS
LOGIC INPUT THRESHOLD VOLTAGE (V)
LOGIC INPUT THRESHOLD VOLTAGE (V)
0.8
Logic Input Threshold Voltages
Logic Hi-Z to High State Transitions
6
5
4
3
2
VOUT = 1.8V, VBIAS = 3.3V
VOUT = 1.2V, VBIAS = 3.3V
VOUT = 0.8V, VBIAS = 2.5V
5.00
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3070 G25
VOUT = 1.8V
VOUT = 1.2V
VOUT = 0.8V
1
0
0
0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
IN-TO-OUT VOLTAGE DIFFERENTIAL (V)
3070 G26
3070fa
LT3070
Typical Performance Characteristics
60
50
40
30
20
VBIAS = 2.5V + 500mVP-P
VBIAS = 2.7V + 500mVP-P
VBIAS = 3.3V + 500mVP-P
10
0
10
100
70
70
60
50
40
COUT = 117µF
COUT = 16.9µF
30
20
VOUT = 1V
VIN = 1.3V + 50mVP-P RIPPLE
VBIAS = 2.5V
IOUT = 1A
10
1k
10k 100k
FREQUENCY (Hz)
1M
0
10M
10
100
1k
10k 100k
FREQUENCY (Hz)
1M
3070 G27
IOUT = 5A
3.6
VOUT = 1.8V
VOUT = 1.2V
VOUT = 0.8V
3.4
3.2
3.0
2.8
2.6
2.4
3.2
3.0
0
1
2
4
3
OUTPUT CURRENT (A)
BIAS VOLTAGE LINE REGULATION (µV)
LOAD REGULATION (mV)
10M
IOUT = 5A
TJ = 25°C
2.8
2.6
2.4
2.2
1.8
0.7
5
0.9
1.5
1.1
1.3
OUTPUT VOLTAGE (V)
1.7
1.9
3070 G51
Bias Voltage Line Regulation
400
800
3070 G32
1M
3.0
Bias Voltage Line Regulation
Load Regulation
–10
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
1k
10k 100k
FREQUENCY (Hz)
3070 G31
0
VOUT = 0.8V
VOUT = 1.2V
VOUT = 1.8V
100
2.0
3070 G30
VIN = VOUT(NOMINAL) + 300mV
VBIAS = 3.3V
$IOUT = 100mA TO 5A
10
3070 G29
3.2
2.4
2.0
–4
VOUT = 1V
VIN = 1.3V + 50mVP-P RIPPLE
VBIAS = 2.5V
IOUT = 5A
Minimum BIAS Voltage vs VOUT
2.6
2.0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
–8
20
3.4
2.8
2.2
–2
COUT = 117µF
COUT = 16.9µF
30
0
10M
VIN = VOUT(NOMINAL) + 300mV
$VOUT = –1%, TJ = 25°C
VOUT = 1.8V
VOUT = 1.5V
VOUT = 1.2V
VOUT = 0.8V TO 1V
3.4
2.2
–6
40
Minimum BIAS Voltage vs IOUT
3.6
MINIMUM BIAS VOLTAGE (V)
MINIMUM BIAS VOLTAGE (V)
3.8
50
3070 G28
Minimum BIAS Voltage
vs Temperature
4.0
60
10
MINIMUM BIAS VOLTAGE (V)
70
80
VBIAS = 2.2V TO 3.6V
700 VIN = 1.1V
VOUT = 0.8V
600 IOUT = 10mA
BIAS VOLTAGE LINE REGULATION (µV)
BIAS PIN RIPPLE REJECTION (dB)
80
80
IN PIN RIPPLE REJECTION (dB)
VIN = 1.3V
VOUT = 1V
IOUT = 5A
COUT = 10µF + 4.7µF + 2.2µF
90
IN Pin Ripple Rejection
IN Pin Ripple Rejection
IN PIN RIPPLE REJECTION (dB)
BIAS Pin Ripple Rejection
100
500
400
300
200
100
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3070 G33
VBIAS = 3.25V TO 3.6V
300 VIN = 2.1V
VOUT = 1.8V
200 IOUT = 10mA
100
0
–100
–200
–300
–400
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3070 G34
3070fa
LT3070
Typical Performance Characteristics
200
150
100
50
250
200
150
100
50
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
0
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
Nap Mode Recovery Time vs IOUT
1.0
250
200
150
NOISE SPECTRAL DENSITY (µV/√Hz)
NAP MODE RECOVERY TIME (µs)
300
100
50
0
0
1
2
4
3
OUTPUT CURRENT (A)
14
12
10
8
6
4
2
0.1
0.3
0.4
0.2
REF/BYP CAPACITANCE (µF)
0
RMS Output Noise
vs Output Current
5
80
VBIAS = 2.5V
VOUT = 1V
IOUT = 5A
COUT = 16.9µF
CREF/BYP = 0.01µF
0.1
70
0.01
0.001
VIN = VOUT(NOMINAL) + 300mV
VBIAS = 3.3V
COUT = 16.9µF
60
50
40
30
20
10
100
10
3070 G38
1k
10k
FREQUENCY (Hz)
0.5
3070 G37
Output Noise Spectral Density
VBIAS = 3.3V
VIN = VOUT(NOM) + 300mV
EN = LOW TO HIGH
IOUT = 5A (SET BY A RESISTOR LOAD)
TJ = 25°C
VOUT = 1.8V,
COUT = 117µF
VOUT = 1.2V,
COUT = 117µF
VOUT = 0.8V,
COUT = 117µF
350
16
3070 G36
3070 G35
400
VBIAS = 2.5V TO 3.3V
IOUT = 10mA
COUT = 10µF + 4.7µF + 2.2µF
TJ = 25°C
SEE APPLICATIONS
INFORMATION FOR
START-UP DETAILS
18
0
OUTPUT NOISE (µVRMS)
250
20
VBIAS = 3.3V
VIN = 2.05V TO 2.7V
VOUT = 1.8V
IOUT = 10mA
OUTPUT VOLTAGE START-UP TIME (ms)
300
VBIAS = 3.3V
VIN = 1.05V TO 2.7V
VOUT = 0.8V
IOUT = 10mA
INPUT VOLTAGE LINE REGULATION (µV)
INPUT VOLTAGE LINE REGULATION (µV)
300
Output Voltage Start-Up Time
vs CREF/BYP
Input Voltage Line Regulation
Input Voltage Line Regulation
100k
0
0.01
VOUT = 1.8V
VOUT = 1.2V
VOUT = 0.8V
0.1
1
OUTPUT CURRENT (A)
3070 G39
10
3070 G40
Input Voltage Line Transient
Response
Output Noise (10Hz to 100kHz)
VOUT
1mV/DIV
VOUT
100µV/DIV
VIN
50mV/DIV
VOUT = 1V
IOUT = 5A
COUT = 16.9µF
1ms/DIV
3070 G41
VIN = 1.3V
VOUT = 1V
IOUT = 5A
COUT = 16.9µF
20µs/DIV
3070 G42
3070fa
10
LT3070
Typical Performance Characteristics
VIOC Amplifier IN-to-OUT Servo
Voltage
VOUT
10mV/DIV
VBIAS
200mV/DIV
VIN = 1.3V
VBIAS = 2.5V
VOUT = 1V
IOUT = 5A
COUT = 16.9µF
20µs/DIV
3070 G43
VIOC IN-TO-OUT SERVO VOLTAGE (mV)
350
340
VIOC Amplifier Output Current
vs Temperature
300
VBIAS = 2.5V
VIOC AMPLIFIER OUTPUT CURRENT (µA)
Bias Voltage Line Transient
Response
330
320
310
300
290
280
270
260
250
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
275
IVIOC SOURCING
250
IVIOC SINKING
225
200
175
150
–75 –50 –25 0 25 50 75 100 125 150 175
TEMPERATURE (°C)
3070 G44
Transient Load Response
Transient Load Response
VOUT
50mV/DIV
AC-COUPLED
VOUT
50mV/DIV
AC-COUPLED
IOUT
2A/DIV
∆I = 500mA
TO 5A
IOUT
2A/DIV
∆I = 500mA
TO 5A
VOUT = 1V
20µs/DIV
COUT = 10µF + 4.7µF + 2.2µF
IOUT tRISE/tFALL = 100ns
3070 G46
VOUT = 1V
20µs/DIV
COUT = 117µF
IOUT tRISE/tFALL = 100ns
Transient Load Response
3070 G47
Transient Load Response
VOUT
50mV/DIV
AC-COUPLED
VOUT
50mV/DIV
AC-COUPLED
IOUT
2A/DIV
∆I = 500mA
TO 5A
IOUT
2A/DIV
∆I = 500mA
TO 5A
VOUT = 1V
20µs/DIV
COUT = 10µF + 4.7µF + 2.2µF
IOUT tRISE/tFALL = 1µs
3070 G45
3070 G48
VOUT = 1V
20µs/DIV
COUT = 117µF
IOUT tRISE/tFALL = 1µs
3070 G49
3070fa
11
LT3070
Pin Functions
VIOC (Pin 1): Voltage for In-to-Out Control. The IC incorporates a unique tracking function to control a buck
regulator powering the LT3070’s input. The VIOC pin is
the output of this tracking function that drives the buck
regulator to maintain the LT3070’s input voltage at VOUT +
300mV. This function maximizes efficiency and minimizes
power dissipation. See the Applications Information section for more information on proper control of the buck
regulator.
PWRGD (Pin 2): Power Good. The PWRGD pin is an opendrain NMOS output that actively pulls low if any one of
these fault modes is detected:
• VOUT is less than 90% of VOUT(NOMINAL) on the rising
edge of VOUT .
• VOUT drops below 85% of VOUT(NOMINAL) for more than
25µs.
• Junction temperature typically exceeds 145°C.
• VBIAS is less than its undervoltage lockout threshold.
• The OUT-to-IN reverse-current detector activates.
See the Applications Information section for more information on PWRGD fault modes.
REF/BYP (Pin 3): Reference Filter. The pin is the output
of the bandgap reference and has an impedance of approximately 19kΩ. This pin must not be externally loaded.
Bypassing the REF/BYP pin to GND with a 10nF capacitor
decreases output voltage noise and provides a soft-start
function to the reference. LTC recommends the use of a
high quality, low leakage capacitor. See the Applications
Information section for more information on noise and
output voltage margining considerations.
GND (Pins 4, 9-14, 20, 26, 29): Ground. The exposed pad
(Pin 29) of the QFN package is an electrical connection to
GND. To ensure proper electrical and thermal performance,
solder Pin 29 to the PCB ground and tie to all GND pins
of the package. These GND pins are fused to the internal
die attach paddle and the exposed pad to optimize heat
sinking and thermal resistance characteristics. See the Applications Information section for thermal considerations
and calculating junction temperature.
IN (Pins 5, 6, 7, 8): Input Supply. These pins supply
power to the high current pass transistor. Tie all IN pins
together for proper performance. The LT3070 requires a
bypass capacitor at IN to maintain stability and low input
impedance over frequency. A 47µF input bypass capacitor
suffices for most battery and power plane impedances.
Minimizing input trace inductance optimizes performance.
Applications that operate with low VIN-VOUT differential
voltages and that have large, fast load transients may require
much higher input capacitor requirements to prevent the
input supply from drooping and allowing the regulator to
enter dropout. See the Applications Information section
for more information on input capacitor requirements.
OUT (Pins 15, 16, 17, 18): Output. These pins supply
power to the load. Tie all OUT pins together for proper
performance. A minimum output capacitance of 15µF is
required for stability. LTC recommends low ESR, X5R or
X7R dielectric ceramic capacitors for best performance.
A parallel ceramic capacitor combination of 10µF + 4.7µF
+ 2.2µF or 15 1µF ceramic capacitors in parallel provide
excellent stability and load transient response. Large load
transient applications require larger output capacitors to
limit peak voltage transients. See the Applications Information section for more information on output capacitor
requirements.
SENSE (Pin 19): Kelvin Sense for OUT . The SENSE pin is
the inverting input to the error amplifier. Optimum regulation
is obtained when the SENSE pin is connected to the OUT
pins of the regulator. In critical applications, the resistance
(RP) of PCB traces between the regulator and the load cause
small voltage drops, creating a load regulation error at the
point of load. Connecting the SENSE pin at the load instead
of directly to OUT eliminates this voltage error. Figure 1
illustrates this Kelvin-Sense connection method. Note that
the voltage drop across the external PCB traces adds to the
dropout voltage of the regulator. The SENSE pin input bias
current depends on the selected output voltage. SENSE
pin input current varies from 50µA typically at VOUT = 0.8V
to 300µA typically at VOUT = 1.8V.
3070fa
12
LT3070
Pin Functions
+
VBIAS
EN
BIAS
SENSE
IN
VO2
+
OUT
LT3070
VO1
VIN
RP
PWRGD
VO0
LOAD
MARGSEL
MARGTOL
VIOC
REF/BYP
GND
RP
3070 F01
Figure 1. Kelvin Sense Connection
MARGSEL (Pin 21): Margining Enable and Polarity Selection. This three-state pin determines both the polarity and
the active state of the margining function. The logic low
threshold is less than 250mV referenced to GND and enables negative voltage margining. The logic high threshold
is greater than VBIAS – 250mV and enables positive voltage
margining. The voltage range between these two logic
thresholds as set by a window comparator defines the
logic Hi-Z state and disables the margining function.
MARGTOL (Pin 22): Margining Tolerance. This threestate pin selects the absolute value of margining (1%,
3% or 5%) if enabled by the MARGSEL input. The logic
low threshold is less than 250mV referenced to GND and
enables either ±1% change in VOUT depending on the state
of the MARGSEL pin. The logic high threshold is greater
than VBIAS – 250mV and enables either ±5% change in
VOUT depending on the state of the MARGSEL pin. The
voltage range between these two logic thresholds as set
by a window comparator defines the logic Hi-Z state and
enables either ±3% change in VOUT depending on the state
of the MARGSEL pin.
VO0, VO1 and VO2 (Pins 23, 24, 25): Output Voltage Select. These three-state pins combine to select a nominal
output voltage from 0.8V to 1.8V in increments of 50mV.
Output voltage is limited to 1.8V maximum by an internal
override of VO1 when VO2 = high. The input logic low
threshold is less than 250mV referenced to GND and the
logic high threshold is greater than VBIAS – 250mV. The
range between these two thresholds as set by a window
comparator defines the logic Hi-Z state. See Table 1 in the
Applications Information section that defines the VO2, VO1
and VO0 settings versus VOUT .
BIAS (Pin 27): Bias Supply. This pin supplies current to
the internal control circuitry and the output stage driving
the pass transistor. The LT3070 requires a minimum 2.2µF
bypass capacitor for stability and proper operation. To
ensure proper operation, the BIAS voltage must satisfy
the following conditions: 2.2V ≤ VBIAS ≤ 3.6V and VBIAS ≥
(1.25 • VOUT + 1V). For VOUT ≤ 0.95V, the minimum BIAS
voltage is limited to 2.2V.
EN (Pin 28): Enable. This pin enables/disables the output
device only. The internal reference and all support functions
are active if VBIAS is above its UVLO threshold. Pulling
EN low keeps the reference circuit active, but disables
the output pass transistor and puts the LT3070 into a low
power nap mode. Drive the EN pin with either a digital logic
port or an open-collector NPN or an open-drain NMOS
terminated with a pull-up resistor to VBIAS. The pull-up
resistor must be less than 35k to meet the VIH condition
of the EN pin. If unused, connect EN to BIAS.
3070fa
13
LT3070
Block Diagram
27
BIAS
IN
5-8
UVLO AND
THERMAL
SHUTDOWN
+
ISENSE
REF/BYP
–
+
EAMP
BUF
–
OUT
15-18
LDO CORE
SENSE
DETECT
+
–
1
VIOC
PWRGD
19
2
VOUT(NOM) + 300mV
VREF
GND
4,9-14,20,26,29
REF/BYP
600mV
3
PROGRAM CONTROL
EN
28
VO2 VO1 VO0 MARGSEL MARGTOL
25
24
23
21
22
3070 BD
LOGIC HIGH STATE
VBIAS – 0.25V
–
+
LOGIC Hi-Z STATE
VBIAS
VO2, VO1, VO0
MARGSEL OR
MARGTOL
100k
VBIAS – 0.9V
100k
0.75V
+
–
+
–
HIGH IF IN > VBIAS – 0.25V
HIGH IF IN < VBIAS – 0.9V
AND IN > 0.75V
TO LOGIC
HIGH IF IN < 0.25V
LOGIC LOW STATE
–
0.25V
+
3070fa
14
LT3070
Applications Information
Introduction
Current generation FPGA and ASIC processors place
stringent demands on the power supplies that power the
core, I/O and transceiver channels. These microprocessors
may cycle load current from near zero to amps in tens of
nanoseconds. Output voltage specifications, especially in
the 1V range, require tight tolerances including transient
response as part of the requirement. Some ASIC processors
require only a single output voltage from which the core
and I/O circuitry operate. Some high performance FPGA
processors require separate power supply voltages for the
processor core, the I/O, and the transceivers. Often, these
supply voltages must be low noise and high bandwidth
to achieve the lowest bit-error rates. These requirements
mandate the need for very accurate, low noise, high current, very high speed regulator circuits that operate at low
input and output voltages.
The LT3070 is a low voltage, UltraFast transient response
linear regulator. The device supplies up to 5A of output
current with a typical dropout voltage of 85mV. A 0.01µF
reference bypass capacitor decreases output voltage noise
to 25µVRMS (BW = 10Hz to 100kHz). The LT3070’s high
bandwidth provides UltraFast transient response using low
ESR ceramic output capacitors (15µF minimum), saving
bulk capacitance, PCB area and cost.
The LT3070’s features permit state-of-the-art linear regulator performance. The LT3070 is ideal for high performance
FPGAs, microprocessors, sensitive communication supplies, and high current logic applications that also operate
over low input and output voltages.
Output voltage for the LT3070 is digitally selectable in
50mV increments over a 0.8V to 1.8V range. A margining
function allows the user to adjust system output voltage
in increments of ±1%, ±3% or ±5%.
The IC incorporates a unique tracking function, which if
enabled by the user, controls an upsteam regulator powering the LT3070’s input (see Figure 8). This tracking function
drives the buck regulator to maintain the LT3070’s input
voltage to VOUT + 300mV. This input-to-output voltage
control allows the user to change the regulator output
voltage, and have the switching regulator powering the
LT3070’s input to track to the optimum input voltage with
no component changes.
This combines the efficiency of a switching regulator
with superior linear regulator response. It also permits
thermal management of the system even with a maximum
5A output load.
LT3070 internal protection includes input undervoltage
lockout (UVLO), reverse-current protection, precision current limiting with power foldback and thermal shutdown.
The LT3070 regulator is available in a thermally enhanced
28-lead, 4mm × 5mm QFN package.
The LT3070’s architecture drives an internal N-channel
power MOSFET as a source follower. This configuration
permits a user to obtain an extremely low dropout, UltraFast transient response regulator with excellent high frequency PSRR performance. The LT3070 achieves superior
regulator bandwidth and transient load performance by
eliminating expensive bulk tantalum or electrolytic capacitors in the most modern and demanding microprocessor
applications. Users realize significant cost savings as all
additional bulk capacitance is removed. The additional
savings of insertion cost, purchasing/inventory cost and
board space are readily apparent. Precision incremental
output voltage control accommodates legacy and future
microprocessor power supply voltages.
Output capacitor networks simplify to direct parallel combinations of ceramic capacitors. Often, the high frequency
ceramic decoupling capacitors required by these various
FPGA and ASIC processors are sufficient to stabilize the
system (see Stability and Output Capacitance section). This
regulator design provides ample bandwidth and responds
to transient load changes in a few hundred nanoseconds
versus regulators that respond in many microseconds.
The LT3070 also incorporates precision current limiting,
enable/disable control of output voltage and integrated
overvoltage and thermal shutdown protection. The
LT3070’s unique design combines the benefits of low
dropout voltage, high functional integration, precision
performance and UltraFast transient response, as well as
providing significant cost savings on the output capacitance
needed in fast load transient applications.
As lower voltage applications become increasingly prevalent with higher frequency switching power supplies, the
LT3070 offers superior regulation and an appreciable
3070fa
15
LT3070
Applications Information
component cost savings. The LT3070 steps to the next
level of performance for the latest generation FPGAs, DSPs
and microprocessors. The simple versatility and benefits
derived from these circuits exceed the power supply needs
of today’s high performance microprocessors.
Programming Output Voltage
Three tri-level input pins, VO2, VO1 and VO0, select the
value of output voltage. Table 1 illustrates the 3-bit digital
word to output voltage resulting from setting these pins
high, low or allowing them to float.
These pins may be tied high or low by either pin-strapping
them to VBIAS or driving them with digital ports. Pins that
float may either actually float or require logic that has
Hi-Z output capability. This allows output voltage to be
dynamically changed if necessary.
Output voltage is selectable from a minimum of 0.8V to
a maximum of 1.8V in increments of 50mV. The MSB,
VO2, sets the pedestal voltage, and the LSB’s, VO1 and
VO0 increment VOUT .
Output voltage is limited to 1.8V maximum by an internal
override of VO1 (default to low) when VO2 = high.
Table 1: VO2 to VO0 Settings vs Output Voltage
VO2
VO1
VO0
VOUT(NOM)
VO2
VO1
VO0
VOUT(NOM)
0
0
0
0.80V
Z
0
1
1.35V
0
0
Z
0.85V
Z
Z
0
1.40V
0
0
1
0.90V
Z
Z
Z
1.45V
0
Z
0
0.95V
Z
Z
1
1.50V
0
Z
Z
1.00V
Z
1
0
1.55V
0
Z
1
1.05V
Z
1
Z
1.60V
0
1
0
1.10V
Z
1
1
1.65V
0
1
Z
1.15V
1
X
0
1.70V
0
1
1
1.20V
1
X
Z
1.75V
Z
0
0
1.25V
1
X
1
1.80V
Z
0
Z
1.30V
X = Don’t Care, 0 = Low, Z = Float, 1 = High
The input logic low threshold is less than 250mV referenced to GND and the logic high threshold is greater than
VBIAS – 250mV. The range between these two thresholds
as set by a window comparator defines the logic Hi-Z
state.
REF/BYP—Voltage Reference
This pin is the buffered output of the internal bandgap
reference and has an output impedance of ≅19kΩ. The
design includes an internal compensation pole at fC = 4kHz.
A 10nF REF/BYP capacitor to GND creates a lowpass pole
at fLP = 840Hz. The 10nF capacitor decreases reference
voltage noise to about 10µVRMS and soft-starts the reference. The LT3070 only soft-starts the reference voltage
during an initial turn-on sequence. If the EN pin is toggled
low after initial turn-on, the reference remains powered-up.
Therefore, toggling the EN pin from low to high does not
soft-start the reference. Only by turning the BIAS supply
voltage on and off will the reference be soft-started. Output
voltage noise is the RMS sum of the reference voltage
noise in addition to the amplifier noise.
The REF/BYP pin must not be DC loaded by anything except
for applications that parallel other LT3070 regulators for
higher output currents. Consult the Applications Section
on Paralleling for further details.
Output Voltage Margining
Two tri-level input pins, MARGSEL (polarity) and MARGTOL
(scale), select the polarity and amount of output voltage
margining. Margining is programmable in increments of
±1%, ±3% and ±5%. Margining is internally implemented
as a scaling of the reference voltage.
Table 2 illustrates the 2-bit digital word to output voltage
margining resulting from setting these pins high, low or
allowing them to float.
These pins may be set high or low by either pin-strapping
them to VBIAS or driving them with digital ports. Pins that
float may either actually float or require logic that has
“Hi-Z” output capability. This allows output voltage to be
dynamically margined if necessary.
The MARGSEL pin determines both the polarity and the active state of the margining function. The logic low threshold
is less than 250mV referenced to GND and enables negative
voltage margining. The logic high threshold is greater than
VBIAS – 250mV and enables positive voltage margining.
The voltage range between these two logic thresholds as
set by a window comparator defines the logic Hi-Z state
and disables the margining function.
3070fa
16
LT3070
Applications Information
The MARGTOL pin selects the absolute value of margining (1%, 3% or 5%) if enabled by the MARGSEL input.
The logic low threshold is less than 250mV referenced to
GND and enables either ±1% change in VOUT depending
on the state of the MARGSEL pin. The logic high threshold
is greater than VBIAS – 250mV and enables either ±5%
change in VOUT depending on the state of the MARGSEL
pin. The voltage range between these two logic thresholds as set by a window comparator defines the logic Hi-Z state
and enables either ±3% change in VOUT depending on the
state of the MARGSEL pin.
Table 2: Programming Margining
MARGSEL
0
0
0
Z
Z
Z
1
1
1
MARGTOL
0
Z
1
0
Z
1
0
Z
1
% OF VOUT(NOM)
–1
–3
–5
0
0
0
1
3
5
Enable Function—Turning On and Off
The EN pin enables/disables the output device only. The
LT3070 reference and all support functions remain active
if VBIAS is above its UVLO threshold. Pulling the EN pin
low puts the LT3070 into nap mode. In nap mode, the
reference circuit is active, but the output is disabled and
quiescent current decreases.
Drive the EN pin with either a digital logic port or an opencollector NPN or an open-drain NMOS terminated with
a pull-up resistor to VBIAS. The pull-up resistor must be
less than 35k to meet the VIH condition of the EN pin. If
unused, connect EN to BIAS.
Input Undervoltage Lockout on BIAS Pin
An internal undervoltage lockout (UVLO) comparator
monitors the BIAS supply voltage. If VBIAS drops below
the UVLO threshold, all functions shut down, the pass
transistor is gated off and output current falls to zero. The
typical BIAS pin UVLO threshold is 1.55V on the rising
edge of VBIAS. The UVLO circuit incorporates about 150mV
of hysteresis on the falling edge of VBIAS.
High Efficiency Linear Regulator—Input-to-Output
Voltage Control
The VIOC (voltage input-to-output control) pin is a function
to control a switching regulator and facilitate a design solution that maximizes system efficiency at high load currents
and still provides low dropout voltage performance.
The VIOC pin is the output of an integrated transconductance amplifier that sources and sinks about 250µA
of current. It typically regulates the output of most LTC®
switching regulators or LTM® power modules, by sinking
current from the ITH compensation node. The VIOC function
controls a buck regulator powering the LT3070’s input by
maintaining the LT3070’s input voltage to VOUT + 300mV.
This 300mV VIN-VOUT differential voltage is chosen to
provide fast transient response and good high frequency
PSRR while minimizing power dissipation and maximizing
efficiency. For example, 1.5V to 1.2V conversion and 1.3V
to 1V conversion yield 1.5W maximum power dissipation
at 5A full output current.
Figure 2 depicts that the switcher’s feedback resistor network sets the maximum switching regulator output voltage
if the linear regulator is disabled. However, once the LT3070
is enabled, the VIOC feedback loop decreases the switching
regulator output voltage back to VOUT + 300mV.
Using the VIOC function creates a feedback loop between
the LT3070 and the switching regulator. As such, the feedback loop must be frequency compensated for stability.
Fortunately, the connection of VIOC to many LTC switching
regulator ITH pins represents a high impedance characteristic which is the optimum circuit node to frequency
compensate the feedback loop. Figure 2 illustrates the
typical frequency compensation network used at the VIOC
node to GND.
The VIOC amplifier characteristics are:
gm = 3.2mS, IOUT = ±250µA, BW = 10MHz.
If the VIOC function is not used, terminate the VIOC pin to GND
with a small capacitor (1000pF) to prevent oscillations.
3070fa
17
LT3070
Applications Information
LT3070
IN
OUT
SWITCHING REGULATOR
REF
+
–
LOAD
–
+
PWM
FB
VOUT +
VREF 300mV
VIOC
REFERENCE
ITH
3070 F02
Figure 2. VIOC Control Block Diagram
PWRGD—Power Good
PWRGD pin is an open-drain NMOS digital output that
actively pulls low if any one of these fault modes is detected:
• VOUT is less than 90% of VOUT(NOMINAL) on the rising
edge of VOUT .
• VOUT drops below 85% of VOUT(NOMINAL) for more than
25µs.
• VBIAS is less than its undervoltage lockout threshold.
• The OUT-to-IN reverse-current detector activates.
• Junction temperature exceeds 145°C typically.*
*The junction temperature detector is an early warning
indicator that trips approximately 20°C before thermal
shutdown engages.
Stability and Output Capacitance
The LT3070’s feedback loop requires an output capacitor
for stability. Choose COUT carefully and mount it in close
proximity to the LT3070’s OUT and GND pins. Include wide
routing planes for OUT and GND to minimize inductance.
If possible, mount the regulator immediately adjacent to
the application load to minimize distributed inductance
for optimal load transient performance. Point-of-Load
applications present the best case layout scenario for
extracting full LT3070 performance.
Low ESR, X5R or X7R ceramic chip capacitors are the
LTC recommended choice for stabilizing the LT3070. Additional bulk capacitors distributed beyond the immediate
decoupling capacitors are acceptable as their parasitic ESL
and ESR, combined with the distributed PCB inductance
isolates them from the primary compensation pole provided
by the local surface mount ceramic capacitors.
The LT3070 requires a minimum output capacitance of
15µF for stability. LTC strongly recommends that the output
capacitor network consist of several low value ceramic
capacitors in parallel.
Why Do Multiple, Small-Value Output Capacitors
Connected in Parallel Work Better?
The LT3070’s unity-gain bandwidth with COUT of 15µF is
about 1MHz at its full-load current of 5A. Surface mounted
MLCC capacitors have a self-resonance frequency of
fR = 1/(2π√LC), which must be pushed to a frequency higher
than the regulator bandwidth. Standard MLCC capacitors
are acceptable. To keep the resonant frequency greater
than 1MHz, the product 1/(2π√LC) must be greater than
1MHz. At this bandwidth, PCB vias can add significant
inductance, thus the fundamental decoupling capacitors
must be mounted on the same plane as the LT3070.
Typical 0603 or 0805 case-size capacitors have an ESL of
~800pH and PCB mounting can contribute up to ~200pH.
Thus, it becomes necessary to reduce the parasitic
3070fa
18
LT3070
Applications Information
inductance by using a parallel capacitor combination.
A suitable methodology must control this paralleling as
capacitors with the same self-resonant frequency, fR, will
form a tank circuit that can induce ringing of their own
accord. Small amounts of ESR (5mΩ to 20mΩ) have some
benefit in dampening the resonant loop, but higher ESRs
degrade the capacitor response to transient load steps
with rise/fall times less than 1µs. The most area efficient
parallel capacitor combination is a graduated 4/2/1 scale
of fR of the same case size. Under these conditions, the
individual ESLs are relatively uniform, and the resonance
peaks are deconstructively spread beyond the regulator
bandwidth. The recommended parallel combination that
approximates 15µF is 10µF + 4.7µF + 2.2µF. Capacitors
with case sizes larger than 0805 have higher ESL and
lower ESR (<5mΩ). Therefore, more capacitors with
smaller values (<10µF) must be chosen. Users should
consider new generation, low inductance capacitors to
push out fR and maximize stability. Refer to the surface
mount ceramic capacitor manufacturer’s data sheets for
capacitor specifications. Figure 3 illustrates an optimum
PCB layout for the parallel output capacitor combination,
but also illustrates the GND connection between the IN
capacitor and the OUT capacitors to minimize the AC
GND loop for fast load transients. This tight bypassing
connection minimizes EMI and optimizes bypassing.
Many of the applications in which the LT3070 excels,
such as FPGA, ASIC processor or DSP supplies, typically
require a high frequency decoupling capacitor network for
the device being powered. This network generally consists
of many low value ceramic capacitors in parallel. In some
LT3070
SENSE
IN OUT
GND
Lo-Z
INPUT
LOAD PLANE
2.2µF
47µF
4.7µF
10µF
3070 F03
applications, this total value of capacitance may be close
to the LT3070’s minimum 15µF capacitance requirement.
This may reduce the required value of capacitance directly
at the LT3070’s output. Multiple low value capacitors in
parallel present a favorable frequency characteristic that
pushes many of the parasitic poles/zeroes beyond the
LT3070’s unity-gain crossover frequency. This technique
illustrates the method that extracts the full bandwidth
performance of the LT3070.
Give additional consideration to the use of ceramic capacitors. Ceramic capacitors are manufactured with a variety of
dielectrics, each with different behavior across temperature
and applied voltage. The most common dielectrics used
are specified with EIA temperature characteristic codes of
Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics are
good for providing high capacitances in a small package,
but they tend to have strong voltage and temperature
coefficients as shown in Figures 4 and 5. When used with
a 5V regulator, a 16V 10µF Y5V capacitor can exhibit an
effective value as low as 1µF to 2µF for the DC bias voltage
applied and over the operating temperature range. The X5R
and X7R dielectrics result in more stable characteristics
and are more suitable for use as the output capacitor.
The X7R type has better stability across temperature,
while the X5R is less expensive and is available in higher
values. Care still must be exercised when using X5R and
X7R capacitors; the X5R and X7R codes only specify
operating temperature range and maximum capacitance
change over temperature. Capacitance change due to
DC bias with X5R and X7R capacitors is better than Y5V
and Z5U capacitors, but can still be significant enough to
drop capacitor values below appropriate levels. Capacitor
DC bias characteristics tend to improve as component
case size increases, but expected capacitance at operating voltage should be verified. Voltage and temperature
coefficients are not the only sources of problems. Some
ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due
to mechanical stress, similar to the way a piezoelectric
microphone works. For a ceramic capacitor the stress
can be induced by vibrations in the system or thermal
transients.
Figure 3. Example PCB Layout
3070fa
19
LT3070
Applications Information
20
0
CHANGE IN VALUE (%)
the LT3070 back to the power supply ground), large input
capacitors are required to avoid an unstable application.
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
X5R
–20
–40
–60
Y5V
–80
–100
0
2
10 12
4
8
6
DC BIAS VOLTAGE (V)
14
16
3070 F04
Figure 4. Ceramic Capacitor DC Bias Characteristics
40
CHANGE IN VALUE (%)
20
0
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
X5R
–20
–40
Y5V
–60
–80
–100
–50 –25
50
25
75
0
TEMPERATURE (°C)
100
125
3070 F05
Figure 5. Ceramic Capacitor Temperature Characteristics
Stability and Input Capacitance
The LT3070 is stable with a minimum capacitance of
47µF connected to its IN pins. Use low ESR capacitors to
minimize instantaneous voltage drops under large load
transient conditions. Large VIN droops during large load
transients may cause the regulator to enter dropout with
corresponding degradation in load transient response.
Increased values of input and output capacitance may be
necessary depending on an application’s requirements.
Sufficient input capacitance is critical as the circuit is
intentionally operated close to dropout to minimize power.
Ideally, the output impedance of the supply that powers
IN should be less than 10mΩ to support a 5A load with
large transients.
In cases where wire is used to connect a power supply
to the input of the LT3070 (and also from the ground of
This is due to the inductance of the wire forming an LC
tank circuit with the input capacitor and not a result of the
LT3070 being unstable. The self inductance, or isolated
inductance, of a wire is directly proportional to its length.
However, the diameter of a wire does not have a major
influence on its self inductance. For example, one inch of
18-AWG, 0.04 inch diameter wire has 28nH of self inductance. The self inductance of a 2-AWG isolated wire with
a diameter of 0.26 inch is about half the inductance of a
18-AWG wire. The overall self inductance of a wire can
be reduced in two ways. One is to divide the current flowing towards the LT3070 between two parallel conductors
which flows in the same direction in each. In this case,
the farther the wires are placed apart from each other, the
more inductance will be reduced, up to a 50% reduction
when placed a few inches apart. Splitting the wires basically connects two equal inductors in parallel. However,
when placed in close proximity from each other, mutual
inductance is added to the overall self inductance of the
wires. The most effective way to reduce overall inductance
is to place the forward and return-current conductors (the
wire for the input and the wire for the return ground) in
very close proximity. Two 18-AWG wires separated by
0.05 inch reduce the overall self inductance to about onefourth of a single isolated wire. If the LT3070 is powered
by a battery mounted in close proximity with ground and
power planes on the same circuit board, a 47µF input
capacitor is sufficient for stability. However, if the LT3070
is powered by a distant supply, use a low ESR, large value
input capacitor on the order of 330µF. As power supply
output impedance varies, the minimum input capacitance
needed for application stability also varies.
Bias Pin Capacitance Requirements
The BIAS pin supplies current to most of the internal
control circuitry and the output stage driving the pass
transistor. The LT3070 requires a minimum 2.2µF bypass capacitor for stability and proper operation. To
ensure proper operation, the BIAS voltage must satisfy the following conditions: 2.2V ≤ VBIAS ≤ 3.6V and
VBIAS ≥ (1.25 • VOUT + 1V). For VOUT ≤ 0.95V, the
minimum BIAS voltage is limited to 2.2V.
3070fa
20
LT3070
Applications Information
Load Regulation
The LT3070 provides a Kelvin sense pin for VOUT , allowing
the application to correct for parasitic package and PCB
I-R drops. However, LTC recommends that the SENSE pin
terminate in close proximity to the LT3070’s OUT pins.
This minimizes parasitic inductance and optimizes regulation. The LT3070 handles moderate levels of output line
impedance, but excessive impedance between VOUT and
COUT causes excessive phase shift in the feedback loop
and adversely affects stability.
Figure 1 in the Pin Functions section illustrates the KelvinSense connection method that eliminates voltage drops
due to PCB trace resistance. However, note that the voltage
drop across the external PCB traces adds to the dropout
voltage of the regulator. The SENSE pin input bias current
depends on the selected output voltage. SENSE pin input
current varies from 50µA typically at VOUT = 0.8V to 300µA
typically at VOUT = 1.8V.
Short-Circuit and Overload Recovery
Like many IC power regulators, the LT3070 has safe operating area (SOA) protection. The safe area protection
decreases current limit as input-to-output voltage increases
and keeps the power transistor inside a safe operating
region for all values of input-to-output voltage up to the
absolute maximum voltage rating. VBIAS must be above
the UVLO threshold for any function. The LT3070 has a
precision current limit specified at ±20% that is active if
VBIAS is above UVLO.
Under conditions of maximum ILOAD and maximum
VIN-VOUT the device’s power dissipation peaks at about
3W. If ambient temperature is high enough, die junction
temperature will exceed the 125°C maximum operating
temperature. If this occurs, the LT3070 relies on two
additional thermal safety features. At about 145°C, the
PWRGD output pulls low providing an early warning of an
impending thermal shutdown condition. At 165°C typically,
the LT3070’s thermal shutdown engages and the output is
shut down until the IC temperature falls below the thermal
hysteresis limit. The SOA protection decreases current limit
as the IN-to-OUT voltage increases and keeps the power
dissipation at safe levels for all values of input-to-output
voltage. The LT3070 provides some output current at all
values of input-to-output voltage up to the absolute maximum voltage rating. See the Current Limit vs VIN curve in
the Typical Performance Characteristics.
During start-up, after the BIAS voltage has cleared its UVLO
threshold and VIN is increasing, output voltage increases
at the rate of current limit charging COUT .
With a high input voltage, a problem can occur where the
removal of an output short will not allow the output voltage to recover. Other regulators with current limit foldback
also exhibit this phenomenon, so it is not unique to the
LT3070. The load line for such a load may intersect the
output current curve at two points: normal operation and
the SOA restricted load current settings. A common situation is immediately after the removal of a short circuit,
but with a static load ≥ 1A. In this situation, removal of the
load or reduction of IOUT to <1A will clear this condition
and allow VOUT to return to normal regulation.
Reverse Voltage
The LT3070 incorporates a circuit that detects if VIN decreases below VOUT . This reverse-voltage detector has
a typical threshold of about (VIN – VOUT) = –6mV. If the
threshold is exceeded, this detector circuit turns off the
drive to the internal NMOS pass transistor, thereby turning
off the output. The output pulls low with the load current
discharging the output capacitance. This circuit’s intent
is to limit and prevent back-feed current from OUT to IN
if the input voltage collapses due to a fault or overload
condition.
Thermal Considerations
The LT3070’s maximum rated junction temperature of
125°C limits its power handling capability and is dominated by the output current multiplied by the input/output
voltage differential:
IOUT • (VIN – VOUT)
The LT3070’s internal power and thermal limiting circuitry
protect it under overload conditions. For continuous normal load conditions, do not exceed the maximum junction
temperature of 125°C. Give careful consideration to all
sources of thermal resistance from junction to ambient.
This includes junction to case, case-to-heat sink interface,
3070fa
21
LT3070
Applications Information
heat sink resistance or circuit board to ambient as the
application dictates. Also, consider additional heat sources
mounted in proximity to the LT3070. The LT3070 is a surface
mount device and as such, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Surface mount heat sinks and
plated through-holes can also be used to spread the heat
generated by power devices. Junction-to-case thermal
resistance is specified from the IC junction to the bottom
of the case directly below the die. This is the lowest resistance path for heat flow. Proper mounting is required to
ensure the best possible thermal flow from this area of the
package to the heat sinking material. Note that the exposed
pad is electrically connected to GND.
Table 3 lists thermal resistance as a function of copper
area in a fixed board size. All measurements were taken
in still air on a 4-layer FR-4 board with 1 oz solid internal
planes and 2 oz top/bottom external trace planes with a
total board thickness of 1.6mm. PCB layers, copper weight,
board layout and thermal vias affect the resultant thermal
resistance. For further information on thermal resistance
and high thermal conductivity test boards, refer to JEDEC
standard JESD51, notably JESD51-12 and JESD51-7.
Achieving low thermal resistance necessitates attention
to detail and careful PCB layout.
Table 3, UFD Plastic Package, 28-Lead QFN
COPPER AREA
TOPSIDE*
BACK SIDE
BOARD AREA
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
2500mm2
2500mm2
2500mm2
30°C/W
1000mm2
2500mm2
2500mm2
32°C/W
225mm2
2500mm2
2500mm2
33°C/W
100mm2
2500mm2
2500mm2
35°C/W
*Device is mounted on topside
Calculating Junction Temperature
Example: Given an output voltage of 0.9V, an input voltage
range of 1.2V ± 5%, a BIAS voltage of 2.5V, a maximum output current of 4A and a maximum ambient temperature of
50°C, what will the maximum junction temperature be?
The power dissipated by the device equals:
IOUT(MAX) • (VIN(MAX) – VOUT) + (IBIAS – IGND) • VOUT
+ IGND • VBIAS
22
where:
IOUT(MAX) = 4A
VIN(MAX) = 1.26V
IBIAS at (IOUT = 4A, VBIAS = 2.5V) = 6.91mA
IGND at (IOUT = 4A, VBIAS = 2.5V) = 0.87mA
thus:
P = 4A(1.26V – 0.9V) + (6.91mA – 0.87mA)0.9V +
0.87mA(2.5V) = 1.448W
With the QFN package soldered to maximum copper
area, the thermal resistance is 30°C/W. So the junction
temperature rise above ambient equals:
1.448W at 30°C/W = 43.44°C
The maximum junction temperature equals the maximum
ambient temperature plus the maximum junction temperature rise above ambient or:
TJMAX = 50°C + 43.44°C = 93.44°C
Applications that cannot support extensive PCB space
for heat sinking the LT3070 require a derating of output
current or increased airflow.
Paralleling Devices for Higher IOUT
Multiple LT3070s may be paralleled to obtain higher output
current. This paralleling concept borrows from the scheme
employed by the LT3080.
To accomplish this paralleling, tie the REF/BYP pins of
the paralleled regulators together. This effectively gives
an averaged value of multiple 600mV reference voltage
sources. Tie the OUT pins of the paralleled regulators to
the common load plane through a small piece of PC trace
ballast or an actual surface mount sense resistor beyond
the primary output capacitors of each regulator. The required ballast is dependent upon the application output
voltage and peak load current. The recommended ballast
is that value which contributes 1% to load regulation. For
example, two LT3070 regulators configured to output 1V,
sharing a 10A load require 2mΩ of ballast at each output.
The Kelvin SENSE pins connect to the regulator side of
the ballast resistors to keep the individual control loops
from conflicting with each other (see Figures 8 and 9).
3070fa
LT3070
Applications Information
Keep this ballast trace area free of solder to maintain a
controlled resistance.
Table 4 shows a simple guideline for PCB trace resistance
as a function of weight and trace width.
Table 4. PC Board Trace Resistance
WEIGHT (Oz)
100 MIL WIDTH*
200 MIL WIDTH*
1
5.43
2.71
2
2.71
1.36
*Trace resistance is measured in milliohms/in
Quieting the Noise
The LT3070 offers numerous noise performance advantages. Each LDO has several sources of noise. An LDO’s
most critical noise source is the reference, followed by
the LDO error amplifier. Traditional low noise regulators
buffer the voltage reference out to an external pin (usually
through a large value resistor) to allow for bypassing and
PWRGD
2.2µF
IN
330µF
EN
VO0
BIAS
PWRGD
SENSE
LT3070 OUT
VO1
2.2µF*
VO2
NC
MARGSEL
NC
MARGTOL
VIOC
1nF
This approach also accommodates reference sharing
between LT3070 regulators that are hooked up in current sharing applications. The REF/BYP filter capacitor
delays the initial power-up time by a factor of the RC time
constant. VREF remains active in nap mode, thus start-up
time is significantly reduced and well controlled coming
out of nap mode (EN:LO↑HI).
50k
VBIAS
2.5V TO 3.6V
VIN
1.5V
noise reduction of reference noise. The LT3070 deviates
from the traditional voltage reference by generating a
low voltage VREF from a reference current into an internal resistor ≅19k. This intermediate impedance node
(REF/BYP) facilitates external filtering directly. A 10nF filter
capacitor minimizes reference noise to 10µVRMS at the
600mV REF/BYP pin, equivalently a 17µV contribution to
output noise at VOUT = 1V. See the Typical Performance
Characteristics for Noise vs Output Voltage performance
as a function of CREF/BYP .
REF/BYP
GND
4.7µF*
10µF*
VOUT
1.2V
5A
*X5R OR X7R CAPACITORS
0.01µF
3070 F06
Figure 6. 1.5V to 1.2V Linear Regulator
3070fa
23
LT3070
Applications Information
VBIAS
3.3V
47µF
6.3V
s3
1Ω
50k
SVIN
NC
PGOOD RUN
PVIN
PVIN
SVIN TRACK
PVIN
SW
PVIN
SW
PLLLPF
SW
LTC3415EUHF
CLKOUT
VO0
ITH
VO1
VO2
NC
MARGTOL
MGN
NC
MARGSEL
100µF
6.3V
s2
NC
SVIN
4.7µF*
*X5R OR X7R CAPACITORS
REF/BYP
GND
2k
4.7nF
VOUT
1V
5A
10µF*
OUT
2.2µF*
VIOC
10k
PWRGD
SENSE
LT3070
NC
ITHM
MODE
IN
NC
20k
VFB
PGND
CLKIN
BIAS
EN
1.3V/5A
47µF
BSEL
PHMODE
NC
0.2µH
SW
SGND
NC
PWRGD
2.2µF
0.1µF
0.01µF
1nF
SGND
PGND PGND PGND PGND
3070 F07
PGND PGND
NOTE: LTC3415 SWITCHER, 2MHz INTERNAL OSCILLATOR
LTC3415 AND LT3070 ON SAME PCB POWER PLANE
Figure 7. Regulator with VIOC Buck Control
VBIAS
3.3V
47µF
6.3V
s3
50k
1Ω
PWRGD
2.2µF
SVIN
NC
0.1µF
PGOOD RUN
NC
PVIN
PVIN
SVIN TRACK
SW
PVIN
SW
PVIN
SW
PLLLPF
SW
CLKOUT
LTC3415EUHF
CLKIN
MODE
PGND PGND PGND PGND
PGND
BIAS
EN
1.3V/7A
IN
47µF
NC
VO0
NC
VO1
VO2
NC
MARGTOL
NC
MARGSEL
ITHM
NC
VIOC
17.5k
1%
15k
1%
4.7µF*
10µF*
RTRACE
3mΩ
CONTROLLED
P.O.L. 1
POWER
PLANE
1V/8A
0.01µF
P.O.L. 2
2.2µF
SGND
PGND PGND
NOTE: LTC3415 SWITCHER, 2MHz INTERNAL OSCILLATOR
LTC3415 AND LT3070 s2 ON SAME PCB POWER PLANE
2.2µF*
REF/BYP
GND
1nF
100µF
6.3V
s2
VOUT
1V
3.5A
OUT
*X5R OR X7R CAPACITORS
ITH
BSEL
PWRGD
SENSE
LT3070
MGN
VFB
PHMODE
NC
0.2µH
SGND
EN
BIAS
IN
47µF
VO0
NC
VO1
VO2
NC
MARGTOL
NC
MARGSEL
VIOC
1nF
PWRGD
SENSE
LT3070
NC
RTRACE
3mΩ
CONTROLLED
OUT
2.2µF*
4.7µF*
10µF*
VOUT
1V
3.5A
*X5R OR X7R CAPACITORS
REF/BYP
GND
0.01µF
3070 F08
Figure 8. 1V, 7A Point-of-Load Current Sharing Regulators
3070fa
24
LT3070
Typical Applications
50k
VIN
3.3V
EN
NC
VO0
NC
VO1
VO2
NC
MARGTOL
NC
MARGSEL
1nF
NC
10µF
10µF
NC
NC
NC
SW1 CLKIN1 CLKOUT1 CLKIN2 CLKOUT2
VIN1
VOUT1
SVIN1
MGN1
RUN1
FB1
PLLLPF1
ITH1
MODE1
ITHM1
PHMODE1
BSEL1
TRACK1
PGOOD1
LTM4616
VIN2
VOUT2
SVIN2
MGN2
RUN2
FB2
PLLLPF2
ITH2
MODE2
ITHM2
PHMODE2
BSEL2
TRACK2
PGOOD2
SW2
SGND1 GND1
VIN
3.3V
NC
EN
100µF
6.3V
X5R
10k
NC
NC
4.7nF
VBUCK2 2.1V/8A
VO1
VO2
NC
MARGTOL
NC
MARGSEL
VIOC
EN
VO0
4.7nF
RTRACE
2.5mΩ
CONTROLLED
P.O.L. 1
POWER
PLANE
1V/7A
0.01µF
RTRACE
2.5mΩ
CONTROLLED
PWRGD
SENSE
10µF*
VOUT
1V
4A
10µF*
VOUT
1.8V
5A
10µF*
VOUT
1.5V
3A
OUT
2.2µF*
4.7µF*
*X5R OR X7R CAPACITORS
REF/BYP
GND
BIAS
0.01µF
VO1
VO2
NC
MARGTOL
NC
MARGSEL
1nF
VIN
3.3V
PWRGD
SENSE
LT3070
NC
VIOC
2k
10µF*
*X5R OR X7R CAPACITORS
LT3070
IN
20k
4.7µF*
2.2µF
47µF
10k
BIAS
NC
VIN
3.3V
NC
2.2µF*
P.O.L. 2
VO0
1nF
VOUT
1V
4A
OUT
REF/BYP
GND
NC
NC
NC
SGND2 GND2
NOTE: THE TWO LTM4616 MODULE CHANNELS ARE
INDEPENDENTLY CONTROLLED BY THE VIOC
CONTROLS FROM THE LINEAR REGULATORS
LT3070
IN
47µF
2k
100µF
6.3V
X5R
VIOC
PWRGD
SENSE
2.2µF
VBUCK1 1.3V/8A
20k
BIAS
IN
47µF
VIN
3.3V
PWRGD
2.2µF
OUT
2.2µF*
4.7µF*
*X5R OR X7R CAPACITORS
REF/BYP
GND
0.01µF
2.2µF
EN
BIAS
IN
47µF
VO0
LT3070
NC
VO1
NC
NC
VO2
NC
MARGSEL
OUT
MARGTOL
VIOC
1nF
PWRGD
SENSE
REF/BYP
GND
2.2µF*
4.7µF*
*X5R OR X7R CAPACITORS
0.01µF
3070 F09
Figure 9. Triple Output Supply Providing 1V, 8A and 1.8V, 5A and 1.5V, 3A
3070fa
25
LT3070
Package Description
UFD Package
28-Lead Plastic QFN (4mm × 5mm)
(Reference LTC DWG # 05-08-1712 Rev B)
0.70 p0.05
4.50 p 0.05
3.10 p 0.05
2.50 REF
2.65 p 0.05
3.65 p 0.05
PACKAGE OUTLINE
0.25 p0.05
0.50 BSC
3.50 REF
4.10 p 0.05
5.50 p 0.05
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
4.00 p 0.10
(2 SIDES)
0.75 p 0.05
R = 0.05
TYP
PIN 1 NOTCH
R = 0.20 OR 0.35
s 45o CHAMFER
2.50 REF
R = 0.115
TYP
27
28
0.40 p 0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
5.00 p 0.10
(2 SIDES)
3.50 REF
3.65 p 0.10
2.65 p 0.10
(UFD28) QFN 0506 REV B
0.200 REF
0.00 – 0.05
0.25 p 0.05
0.50 BSC
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WXXX-X).
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
3070fa
26
LT3070
Revision History
REV
DATE
DESCRIPTION
PAGE NUMBER
A
5/10
Entire data sheet revised
1 to 28
3070fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
27
LT3070
Typical Application
50k
VBIAS
2.5V TO 3.6V
VIN
1.5V
PWRGD
2.2µF
IN
330µF
EN
VO0
BIAS
PWRGD
SENSE
LT3070 OUT
VO1
2.2µF*
VO2
NC
MARGSEL
NC
MARGTOL
VIOC
1nF
REF/BYP
GND
4.7µF*
10µF*
VOUT
1.2V
5A
*X5R OR X7R CAPACITORS
0.01µF
3070 TA02
1.5V to 1.2V Linear Regulator
Related Parts
PART
DESCRIPTION
COMMENTS
LT1763
500mA, Low Noise LDO
300mV Dropout Voltage, Low Noise: 20µVRMS, VIN: 1.8V to 20V,
SO-8 Package
LT1764/LT1764A
3A, Fast Transient Response, Low Noise LDO
340mV Dropout Voltage, Low Noise: 40µVRMS, VIN: 2.7V to 20V,
TO-220 and DD Packages “A” Version Stable Also with Ceramic Caps
LT1963/LT1963A
1.5A Low Noise, Fast Transient Response LDO
340mV Dropout Voltage, Low Noise: 40µVRMS, VIN: 2.5V to 20V,
“A” Version Stable with Ceramic Caps, TO-220, DD, SOT-223 and
SO-8 Packages
LT1965
1.1A, Low Noise, Low Dropout Linear Regulator
290mV Dropout Voltage, Low Noise: 40µVRMS, VIN: 1.8V to 20V,
VOUT : 1.2V to 19.5V, Stable with Ceramic Caps, TO-220, DD-Pak,
MSOP and 3mm × 3mm DFN Packages
LT3021
500mA, Low Voltage, VLDO™ Linear Regulator
VIN: 0.9V to 10V, Dropout Voltage = 160mV (Typ), Adjustable Output
(VREF = VOUT(MIN) = 200mV), Fixed Output Voltages: 1.2V, 1.5V, 1.8V,
Stable with Low ESR, Ceramic Output Capacitors 16-Pin DFN
(5mm × 5mm) and 8-Lead SO Packages
LT3080/LT3080-1
1.1A, Parallelable, Low Noise, Low Dropout Linear Regulator 300mV Dropout Voltage (2-Supply Operation), Low Noise: 40µVRMS,
VIN: 1.2V to 36V, VOUT : 0V to 35.7V, Current-Based Reference with
1 Resistor VOUT Set; Directly Parallelable (No Op Amp Required),
Stable with Ceramic Caps, TO-220, SOT-223, MSOP-8 and 3mm
× 3mm DFN-8 Packages; LT3080-1 has Integrated Internal Ballast
Resistor
LT3085
500mA, Parallelable, Low Noise, Low Dropout
Linear Regulator
275mV Dropout Voltage (2-Supply Operation), Low Noise: 40µVRMS,
VIN: 1.2V to 36V, VOUT : 0V to 35.7V, Current-Based Reference with
1 Resistor VOUT Set; Directly Parallelable (No Op Amp Required),
Stable with Ceramic Caps, MSOP-8 and 2mm × 3mm DFN-6
Packages
LTC3025-1/
LTC3025-2
500mA Micropower VLDO Linear Regulator
in 2mm × 2mm DFN
VIN = 0.9V to 5.5V, Dropout Voltage: 75mV, Low Noise 80µVRMS,
Low IQ: 54µA, Fixed Output: 1.2V (LTC3025-2); Adjustable Output
Range: 0.4V to 3.6V (LTC3025-1) 2mm × 2mm 6-Lead DFN Package
LTC3026
1.5A, Low Input Voltage VLDO Regulator
VIN: 1.14V to 3.5V (Boost Enabled), 1.14V to 5.5V (with External
5V), VDO = 0.1V, IQ = 950µA, Stable with 10µF Ceramic Capacitors,
10-Lead MSOP and DFN-10 Packages
3070fa
28 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507 ● www.linear.com
LT 0510 REV A • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2009