HMC564LC4 v00.0906 AMPLIFIERS - SMT 5 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz Typical Applications Features The HMC564LC4 is ideal for use as a LNA or driver amplifier for: Noise Figure: 1.8 dB • Point-to-Point Radios Gain: 17 dB OIP3: 25 dBm • Point-to-Multi-Point Radios & VSAT Single Supply: +3V @ 51 mA • Test Equipment and Sensors 50 Ohm Matched Input/Output • Military & Space RoHS Compliant 4 x 4 mm Package Functional Diagram General Description The HMC564LC4 is a high dynamic range GaAs PHEMT MMIC Low Noise Amplifier housed in a leadless RoHS compliant 4x4mm SMT package. Operating from 7 to 14 GHz, the HMC564LC4 features extremely flat small signal gain of 17 dB as well as 1.8 dB noise figure and +25 dBm output IP3 across the operating band. This self-biased LNA is ideal for microwave radios due to its consistent output power, single +3V supply operation, and DC blocked RF I/O’s. Electrical Specifications, TA = +25° C, Vdd 1, 2 = +3V Parameter Min. Frequency Range Gain 14 Gain Variation Over Temperature Max. Units GHz 17 dB 0.02 0.03 dB/ °C Noise Figure 1.8 2.2 dB Input Return Loss 15 dB Output Return Loss 14 dB Output Power for 1 dB Compression (P1dB) Saturated Output Power (Psat) 5 - 560 Typ. 7 - 14 10 13 dBm 14.5 dBm Output Third Order Intercept (IP3) 25 Supply Current (Idd)(Vdd = +3V) 51 dBm 75 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com mA HMC564LC4 v00.0906 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz Broadband Gain & Return Loss 5 Gain vs. Temperature 20 20 10 5 GAIN (dB) RESPONSE (dB) 15 S21 S11 S22 0 -5 15 10 -10 +25C +85C -40C 5 -15 -20 -25 0 0 4 8 12 16 6 20 7 8 FREQUENCY (GHz) 11 12 13 14 15 Output Return Loss vs. Temperature 0 0 +25C +85C -40C +25C +85C -40C -5 RETURN LOSS (dB) -5 RETURN LOSS (dB) 10 FREQUENCY (GHz) Input Return Loss vs. Temperature -10 -15 -20 -10 -15 -20 -25 -25 6 7 8 9 10 11 12 13 14 15 6 7 8 FREQUENCY (GHz) 9 10 11 12 13 14 15 13 14 15 FREQUENCY (GHz) Noise Figure vs. Temperature Output IP3 vs. Temperature 6 35 5 30 +25C +85C -40C 4 OIP3 (dBm) NOISE FIGURE (dB) 9 AMPLIFIERS - SMT 25 25 3 25 20 2 15 1 10 0 +25C +85C -40C 5 6 7 8 9 10 11 12 FREQUENCY (GHz) 13 14 15 6 7 8 9 10 11 12 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 561 HMC564LC4 v00.0906 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz P1dB vs. Temperature Psat vs. Temperature 20 20 16 16 Psat (dBm) P1dB (dBm) AMPLIFIERS - SMT 5 12 8 +25C +85C -40C 4 12 +25C +85C -40C 8 4 0 0 6 7 8 9 10 11 12 13 14 15 6 7 8 9 FREQUENCY (GHz) Reverse Isolation vs. Temperature 11 12 13 15 20 Pout (dBm), GAIN (dB), PAE(%) +25C +85C -40C -10 -20 -30 -40 -50 6 7 8 9 10 11 12 13 14 15 10 Pout Gain PAE 5 0 -15 15 -10 FREQUENCY (GHz) -5 INPUT POWER (dBm) 20 10 18 9 8 16 14 P1dB Gain 7 12 6 10 5 4 8 Noise Figure 6 3 4 2 2 1 0 0 2.5 NOISE FIGURE (dB) GAIN (dB), P1dB (dBm) Gain, Power & Noise Figure vs. Supply Voltage @ 8 GHz 3 3.5 Vdd (Vdc) 5 - 562 14 Power Compression @ 8 GHz 0 ISOLATION (dB) 10 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 0 HMC564LC4 Absolute Maximum Ratings Drain Bias Voltage (Vdd1, Vdd2) +3.5 Vdc RF Input Power (RFin) (Vdd = +3.0 Vdc) +5 dBm Channel Temperature 175 °C Continuous Pdiss (T= 85 °C) (derate 12.9 mW/°C above 85 °C) 1.16 W Thermal Resistance (channel to ground paddle) 77.5 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz Typical Supply Current vs. Vdd Vdd (Vdc) Idd (mA) 2.5 49 3.0 51 3.5 53 Note: Amplifier will operate over full voltage ranges shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 5 AMPLIFIERS - SMT v00.0906 Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA. 2. LEAD AND GROUND PADDLE PLATING: GOLD FLASH OVER NICKEL. 3. DIMENSIONS ARE IN INCHES (MILLIMETERS). 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 5. PACKAGE WARP SHALL NOT EXCEED 0.05MM DATUM – C – 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 563 HMC564LC4 v00.0906 AMPLIFIERS - SMT 5 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz Pin Descriptions Function Description 1, 5-8, 9 -14, 18, 20, 21, 22, 24 Pin Number N/C No connection required. These pins may be connected to RF/DC ground without affecting performance. 2, 4, 15, 17 GND Package bottom has an exposed metal paddle that must also be connected to RF/DC ground. 3 RFIN This pin is AC coupled and matched to 50 Ohms. 16 RFOUT This pin is AC coupled and matched to 50 Ohms. 23, 19 Vdd1, Vdd2 Power Supply Voltage for the amplifier. External bypass capacitors of 100 pF, 1000pF, and 2.2 μF are required. Interface Schematic Application Circuit 5 - 564 Component Value C1, C2 100 pF C5, C6 2.2 μF For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC564LC4 v00.0906 GaAs SMT PHEMT LOW NOISE AMPLIFIER, 7 - 14 GHz 5 AMPLIFIERS - SMT Evaluation PCB List of Material for Evaluation PCB 116156 Item J1, J2 Description 2.92 mm PC mount SMA J3 - J7 DC Pin C1 - C2 100 pF capacitor, 0402 pkg. C3 - C4 2.2μF Capacitor, Tantalum U1 HMC564LC4 Amplifier PCB [2] 108535 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350. [1] The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 565