DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI FEATURES GENERAL DESCRIPTION This document describes the specifications for the IDTF1102 Zero-DistortionTM RF to IF Downconverting Mixer. This device is part of a series of downconverting mixers covering all UTRA bands. See the Part# Matrix for the details of all devices in the series. • • • • The F1102 dual channel device operates with a single 5V supply. It is optimized for operation in a Multicarrier BaseStation Receiver for RF bands from 698 to 915 MHz with High or Low Side Injection. IF frequencies from 50 to 300 MHz are supported. The F1102 also supports the 400 MHz RF bands with some simple external matching modifications (see page 25). Nominally, the device offers +43 dBm Output IP3 with 330 mA of ICC. Alternately one can adjust 4 resistor values and a toggle pin to run the devices in low current mode (LC mode) with +36 dBm Output IP3 and 235 mA of ICC. • • • • • • • • • • • COMPETITIVE ADVANTAGE Dual Path for Diversity Systems Ideal for Multi-Carrier Systems 9.0 dB Gain Ultra linear: +43 dBm IP3O (STD Mode) +36 dBm IP3O (LC Mode) Low NF < 10 dB Extended LO level range for MIMO (-6 dBm) 200 Ω output impedance Ultra high +13 dBm P1dBI Pin Compatible with existing solutions 6x6 36 pin package Power Down mode < 200 nsec settling from Power Down Minimizes Synth pulling in Standby Mode Low Current Mode : ICC = 235 mA Standard Mode: ICC = 330 mA DEVICE BLOCK DIAGRAM In typical basestation receivers the mixer limits the linearity performance for the entire receive system. The F1102 with Zero-Distortion technology dramatically improves the maximum IM3 interference that the BTS can withstand at a desired Signal to Noise Ratio (SNR.) Alternately, one can run the device in LC Mode to reduce Power consumption significantly. RFIN_A IFOUT_A STBY RF VCO IP3O: ⇑ 7 dB STD Mode, ⇑ 3 dB LC Mode Dissipation: ⇓ 40% LC Mode, ⇓ 12% STD Mode Allows for higher RF gain improving Sensitivity Bias Control 2 LOISET LCMODE RFIN_B IFOUT_B PART# MATRIX Part# RF freq range UTRA bands IF freq range Typ. Gain Injection 150 - 450 8.3 High Side F1100 698 - 915 5,6,8,12,13,14,17 ,19,20 F 1102 400 - 1000 5,6,8,12,13,14,17 ,1 9 ,2 0 50 - 300 9 .0 Both F11502 1700 - 2200 1,2,3,4,9,10, 33, 34,35, 36, 37,39 50 - 450 8.5 High Side F1152 1400 - 2200 1,2,3,4,9,10, 21 , 241, 33, 34,35, 36, 37,39 50 - 350 8.5 Low Side F1162 2300 – 2700 7,38,40,41 50 – 500 8.8 Low Side ORDERING INFORMATION Omit IDT prefix IDTF1102NBGI8 1 1 2 2 Tape & Reel 0.8 mm height package RF product Line Green Industrial Temp range – with High side injection – With High side or Low side injection IDT Zero-DistortionTM Mixer 1 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI ABSOLUTE MAXIMUM RATINGS VCC to GND STBY, LCMODE IF_A+, IF_B+, IF_A-, IF_B-, LO1_ADJ, LO2_ADJ LO_IN, LO_IN_ALT, RF_A, RF_B IF_BiasA, IF_BiasB to GND RF Input Power (RF_A, RF_B) Continuous Power Dissipation θJA (Junction – Ambient) θJC (Junction – Case) The Case is defined as the exposed paddle Operating Temperature Range (Case Temperature) Maximum Junction Temperature Storage Temperature Range Lead Temperature (soldering, 10s) . -0.3V to +5.5V -0.3V to (VCC_ + 0.3V) -0.3V to (VCC_ + 0.3V) -0.3V to +0.3V -0.3V to +0.3V +20dBm 2.2W +35°C/W +2.5°C/W TC = -40°C to +100°C 150°C -65°C to +150°C +260°C Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. IDT Zero-DistortionTM Mixer 2 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI IDTF1102 SPECIFICATION (400 – 1000 MHZ MIXER W/HIGH OR LOW SIDE INJECTION) Specifications apply at VCC = +5.0V, FRF = 850 MHz, FIF = 200 MHz, Hi-Side, PLO = 0 dBm, TC = +25°C, STBY = GND, LCMODE = VIH (STD Mode), EVKit BOM = Standard Mode, Transformer Loss included (not de-embedded) unless otherwise noted. Parameter Comment Symbol min Logic Input High For Standby, LCMODE Pins VIH 2 Logic Input Low For Standby, LCMODE Pins VIL Logic Current For Standby Pin IIH, IIL -30 Logic Current LCMODE Pin IIH, IIL -100 Supply Voltage(s) All VCC pins Operating Temperature Case Temperature Supply Current Total VCC , STD Mode Total Both Channels typ max units V 0.8 V +30 µA -20 µA VCC 4.75 to 5.25 V TCASE -40 to +100 degC ISTD 330 370 1 mA ILC 235 260 mA ISTBY 22 30 mA Total VCC , LC Mode Supply Current LCMODE = GND EVkit BOM = LC Mode Total Both Channels Standby Mode Supply Current RF Freq Range Operating Range FRF 400 – 1000 MHz IF Freq Range Operating Range FIF 50 to 300 MHz LO Freq Range Operating LO Range FLO 500 to 1150 MHz LO Power Operating LO Range PLO -6 to +6 dBm ZRF 50 Ω ZIF 200 Ω ZLO 50 Ω TSETT 0.175 µsec STBY = VIH Total Both Channels STD Mode 3 RF Input Impedance IF Output Impedance LO port Impedance Settling Time Single Ended Return Loss ~17 dB Differential Return Loss ~ 13 dB Single Ended Return Loss ~15 dB • Pin = -13 dBm • Gate STBY from VIH to VIL • Time for IF Signal to settle to within 0.1 dB of final value Conversion Gain Gain STD Mode • • • • FRF = 698 MHz LCMODE = VIH EVkit BOM = STD Mode FIF = 150 MHz (Low Side Inj.) GSTD 8.5 9.2 9.9 dB GLC 7.8 8.5 9.2 dB Conversion Gain Gain LC Mode IDT Zero-DistortionTM Mixer • • • • FRF = 915 MHz LCMODE = GND EVkit BOM = LC Mode FIF = 200 MHz (High Side Inj.) 3 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI IDTF1102 SPECIFICATION (CONTINUED) Parameter Comment Symbol min typ max units NF STD Mode • LCMODE = VIH • EVkit BOM = STD Mode • FIF = 200 MHz (High Side Inj.) NFSTD 9.5 dB NF LC Mode • LCMODE = GND • EVkit BOM = LC Mode • FIF = 200 MHz (High Side Inj.) NFLC 9.3 dB 21.7 dB 43 dBm 42 dBm 36 dBm -78 dBc -100 MHz offset blocker PIN = +10 dBm FIF = 200 MHz NFBLK PIN = -10 dBm per tone 800 KHz Tone Separation FIF = 200 MHz (High Side Inj.) FRF = 850 MHz IP3O1 PIN = -10 dBm per tone 15 MHz Tone Separation FIF = 200 MHz (High Side Inj.) IP3O2 PIN = -10 dBm per tone FIF = 200 MHz (High Side Inj.) 800 KHz Tone Separation LCMODE = GND FRF = 915 MHz IP3O3 1 dB Compression Input referred P1dBI1 11.9 12.5 dBm 1 dB Compression LCMODE Input referred LCMODE = GND P1dBI2 9.0 10.2 dBm Gain Comp. w/blocker Blocker unmodulated tone PIN = +8 dBm, 20 MHz offset Signal Pin Tone = -20 dBm Measure ∆G of signal ∆GAC 0.15 dB Spur: 5RF X -4LO FLO = 1087.5 MHz FIF = 190 MHz (High Side Inj.) Desired FRF = 897.5 MHz Spur Freq = 908 MHz Pin = +5 dBm STD Mode SPUR1 -97 Channel Isolation IF_B Pout vs. IF_A w/ RF_A input NF w/Blocker Output IP3 – Narrowband Output IP3 – Wideband Output IP3 – LCMODE 2RF – 2LO rejection PRF = -10 dBm Frequency = FRF + ½ FIF 2 33 2x2 ISOC LO to IF leakage RF to IF leakage 39 Pin = -10 dBm LO to RF leakage 45 -89 dBc dB 51 ISOLI -22 -15 dBm ISORI -26 -20 dBm ISOLR -40 dBm Notes: 1 – Items in min/max columns in bold italics are Guaranteed by Test 2 – All other Items in min/max columns are Guaranteed by Design Characterization 3 – Normal RF range is 698 – 915 MHz. See Page 25 for modifications for 400 – 500 MHz operation IDT Zero-DistortionTM Mixer 4 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDTIONS Unless otherwise Noted, the following Apply to the Typ Ops Graphs 800 KHz Tone Spacing High Side injection graphs with 200MHz IF (pages 6 – 10) Low Side injection graphs with 150MHz IF (pages 11 – 14) Average of Channel A & Channel B Pin = – 10 dBm per Tone LO port = Pin 19 (Main Port) Listed Temperatures are Case Temperature (TC or TCASE = Case Temperature) Where noted, TA or TAMB = Ambient Temperature Transformer losses are de-embedded IDT Zero-DistortionTM Mixer 5 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [IF = 200 MHz, High Side Injection] (-1-) Gain vs. TCASE Gain vs. VCC 10 10 9 9 Gain (dB) 11 Gain (dB) 11 8 7 6 5 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 8 7 6 5 4 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 4 650 700 750 800 850 900 950 650 700 750 RF Freq (MHz) 800 850 900 950 RF Freq (MHz) Gain vs. LO Level Output IP3 vs. TCASE 11 50 10 45 Output IP3 (dBm) Gain (dB) 9 8 7 6 5 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC 40 35 30 25 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 20 4 650 700 750 800 850 900 650 950 700 750 RF Freq (MHz) Output IP3 vs. VCC 850 900 950 Output IP3 vs. LO Level 50 50 45 45 Output IP3 (dBm) Output IP3 (dBm) 800 RF Freq (MHz) 40 35 30 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 25 40 35 30 25 20 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC 20 650 700 750 800 850 900 950 650 IDT Zero-DistortionTM Mixer 700 750 800 850 900 950 RF Freq (MHz) RF Freq (MHz) 6 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [IF = 200 MHz, High Side Injection] (-2-) P1dB vs. VCC 15 15 14 14 13 13 Input P1dB (dBm) Input P1dB (dBm) P1dB vs. TCASE 12 11 10 9 8 7 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 12 11 10 9 8 7 6 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 6 650 700 750 800 850 900 950 650 700 750 RF Freq (MHz) P1dB vs. LO Level 14 2 X 2 Rejection [Pin = -10] (dBc) 0 -10 Input P1dB (dBm) 13 12 11 10 9 7 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC 6 900 950 -20 -30 -40 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC -50 -60 -70 -80 -90 -100 650 700 750 800 850 900 950 650 700 750 RF Freq (MHz) -10 -10 2 X 2 Rejection [Pin = -10] (dBc) 0 -20 -40 850 900 950 2RF x 2LO Rejection vs. LO Level 0 -30 800 RF Freq (MHz) 2RF x 2LO Rejection vs. VCC 2 X 2 Rejection [Pin = -10] (dBc) 850 2RF x 2LO rejection vs. TCASE 15 8 800 RF Freq (MHz) 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC -50 -60 -70 -80 -90 -100 -20 -30 -40 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC -50 -60 -70 -80 -90 -100 650 700 750 800 850 900 950 650 RF Freq (MHz) IDT Zero-DistortionTM Mixer 700 750 800 850 900 950 RF Freq (MHz) 7 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [IF = 200 MHz, High Side Injection] (-3-) ICC vs. VCC 0.400 0.400 0.380 0.380 0.360 0.360 Total ICC (Amps) Total ICC (Amps) ICC vs. TCASE 0.340 0.320 0.300 0.280 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 0.340 0.320 0.300 0.280 0.260 0.260 0.240 0.240 0.220 0.220 0.200 650 750 800 850 900 950 650 25 degC - 0 dBm - 4.75 V - LC 700 0.400 0 0.380 -5 LO to IF leakage (dBm) 0.340 0.320 0.300 0.280 750 800 850 900 950 LO-IF Leakage vs. TCASE 0.360 Total ICC (Amps) 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD RF Freq (MHz) ICC vs. LO Level 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC 0.260 0.240 -10 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC -15 -20 -25 -30 -35 -40 -45 0.220 -50 0.200 700 750 800 850 900 650 950 700 750 800 850 900 950 RF Freq (MHz) RF Freq (MHz) LO-IF Leakage vs. LO Level LO-IF Leakage vs. VCC 0 0 -10 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC -5 LO to IF leakage (dBm) -5 LO to IF leakage (dBm) 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 0.200 700 RF Freq (MHz) 650 25 degC - 0 dBm - 5.25 V - STD -15 -20 -25 -30 -35 -40 -10 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC -15 -20 -25 -30 -35 -40 -45 -45 -50 -50 650 700 750 800 850 900 650 950 IDT Zero-DistortionTM Mixer 700 750 800 850 900 950 RF Freq (MHz) RF Freq (MHz) 8 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [IF = 200 MHz, High Side Injection] (-4-) RF-IF Leakage vs. TCASE RF-IF Leakage vs. VCC 0 -5 -10 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC RF to IF leakage [PIN = -10] (dBm) RF to IF leakage [PIN = -10] (dBm) 0 -15 -20 -25 -30 -35 -40 -45 -50 -5 -10 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC -15 -20 -25 -30 -35 -40 -45 -50 650 700 750 800 850 900 950 650 700 RF Freq (MHz) 850 900 950 3RF X 3LO Rejection vs. TCASE 0 0 -5 -10 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC -10 3 X 3 Rejection [PIN = -10] (dBc) RF to IF leakage [PIN = -10] (dBm) 800 RF Freq (MHz) RF-IF Leakage vs. LO Level -15 -20 -25 -30 -35 -40 -45 -20 -30 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC -40 -50 -60 -70 -80 -90 -100 -50 650 700 750 800 850 900 950 650 700 RF Freq (MHz) 0 -10 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 3 X 3 Rejection [PIN = -10] (dBc) 0 -30 800 850 900 950 3RF X 3LO Rejection vs. LO Level -10 -20 750 RF Freq (MHz) 3RF X 3LO Rejection vs. VCC 3 X 3 Rejection [PIN = -10] (dBc) 750 -40 -50 -60 -70 -80 -90 -100 -20 -30 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC -40 -50 -60 -70 -80 -90 -100 650 700 750 800 850 900 950 650 RF Freq (MHz) IDT Zero-DistortionTM Mixer 700 750 800 850 900 950 RF Freq (MHz) 9 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [IF = 200 MHz, High Side Injection] (-5-) Channel Isolation vs. VCC 70 70 65 65 ChA to ChB Isolation (dBc) ChA to ChB Isolation (dBc) Channel Isolation vs. TCASE 60 55 50 45 40 35 30 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 25 60 55 50 45 40 35 30 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 25 20 20 650 700 750 800 850 900 950 650 700 750 Channel Isolation vs. LO Level 850 900 950 Noise Figure vs. TCASE (LC Mode) 14.0 70 65 13.0 60 Noise Figure (dB) ChA to ChB Isolation (dBc) 800 RF Freq (MHz) RF Freq (MHz) 55 50 45 40 35 30 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC -40 degC case - ChA -40 degC case - ChB 25 degC case - ChA 25 degC case - ChB 100 degC case - ChA 100 degC case - ChB 12.0 11.0 10.0 9.0 25 8.0 EVkit RF trace losses de-embedded 20 650 700 750 800 850 900 950 7.0 750 RF Freq (MHz) 800 850 900 950 RF Freq (MHz) Noise Figure vs. TCASE (STD Mode) NF vs. Blocker (RF =850 MHz, IF = 200 MHz, TA = 25C) 14.0 26 -40 degC case - ChB 25 degC case - ChA 25 degC case - ChB 100 degC case - ChA 100 degC case - ChB 24 22 12.0 Noise Figure (dB) Noise Figure (dB) 13.0 -40 degC case - ChA 11.0 10.0 9.0 ChA LC mode ChaA STD mode ChB LC mode ChB STD mode 20 18 16 14 12 10 8.0 8 EVkit RF trace losses de-embedded 7.0 750 800 850 900 6 950 -30 RF Freq (MHz) IDT Zero-DistortionTM Mixer -26 -22 -18 -14 -10 -6 -2 2 6 10 Blocker Input Power (dBm) 10 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [IF = 150 MHz, Low Side Injection] (-6-) Gain vs. TCASE Gain vs. VCC 10 10 9 9 Gain (dB) 11 Gain (dB) 11 8 7 6 5 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 8 7 6 5 4 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 4 700 750 800 850 900 950 700 750 RF Freq (MHz) 800 850 900 950 RF Freq (MHz) Gain vs. LO level Output IP3 vs. TCASE 11 50 10 45 Output IP3 (dBm) Gain (dB) 9 8 7 6 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 5 40 35 30 25 25 degC - -6 dBm - 5.00 V - LC -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 20 4 700 750 800 850 900 700 950 750 RF Freq (MHz) 850 900 950 RF Freq (MHz) Output IP3 vs. VCC Output IP3 vs. LO Level 50 50 45 45 Output IP3 (dBm) Output IP3 (dBm) 800 40 35 30 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 25 40 35 30 25 20 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC 20 700 750 800 850 900 950 700 IDT Zero-DistortionTM Mixer 750 800 850 900 950 RF Freq (MHz) RF Freq (MHz) 11 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [IF = 150 MHz, Low Side Injection] (-7-) P1dB vs. VCC 15 15 14 14 13 13 Input P1dB (dBm) Input P1dB (dBm) P1dB vs. TCASE 12 11 10 9 8 7 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 12 11 10 9 8 7 6 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 6 700 750 800 850 900 950 700 750 RF Freq (MHz) 14 2 X 2 Rejection [Pin = -10] (dBc) 0 -10 Input P1dB (dBm) 13 12 11 10 9 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC 6 950 -20 -30 -40 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC -50 -60 -70 -80 -90 -100 700 750 800 850 900 950 700 750 RF Freq (MHz) -10 -10 2 X 2 Rejection [Pin = -10] (dBc) 0 -20 -40 850 900 950 2RF x 2LO rejection vs. LO Level 0 -30 800 RF Freq (MHz) 2RF x 2LO Rejection vs. VCC 2 X 2 Rejection [Pin = -10] (dBc) 900 2RF x 2LO rejection vs. TCASE 15 7 850 RF Freq (MHz) P1dB vs. LO Level 8 800 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC -50 -60 -70 -80 -90 -100 -20 -30 -40 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC -50 -60 -70 -80 -90 -100 700 750 800 850 900 950 700 RF Freq (MHz) IDT Zero-DistortionTM Mixer 750 800 850 900 950 RF Freq (MHz) 12 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [IF = 150 MHz, Low Side Injection] (-8-) ICC vs. VCC 0.400 0.400 0.380 0.380 0.360 0.360 Total ICC (Amps) Total ICC (Amps) ICC vs. TCASE 0.340 0.320 0.300 0.280 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 0.340 0.320 0.300 0.280 0.260 0.260 0.240 0.240 0.220 0.220 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 0.200 0.200 700 25 degC - 0 dBm - 5.25 V - STD 750 800 850 900 700 950 750 RF Freq (MHz) 0.400 0 0.380 -5 LO to IF leakage (dBm) Total ICC (Amps) 0.360 0.340 0.320 0.280 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC 0.260 0.240 950 -10 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC -15 -20 -25 -30 -35 -40 -50 0.200 750 800 850 900 700 950 750 800 850 900 950 RF Freq (MHz) RF Freq (MHz) LO-IF Leakage vs. LO Level LO-IF Leakage vs. VCC 0 0 -10 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC -5 LO to IF leakage (dBm) -5 LO to IF leakage (dBm) 900 -45 0.220 700 850 LO-IF Leakage vs. TCASE ICC vs. LO Level 0.300 800 RF Freq (MHz) -15 -20 -25 -30 -35 -40 -10 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC -15 -20 -25 -30 -35 -40 -45 -45 -50 -50 700 750 800 850 900 700 950 IDT Zero-DistortionTM Mixer 750 800 850 900 950 RF Freq (MHz) RF Freq (MHz) 13 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [IF = 150 MHz, Low Side Injection] (-9-) RF-IF Leakage vs. TCASE RF-IF Leakage vs. VCC 0 -5 -10 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC RF to IF leakage [PIN = -10] (dBm) RF to IF leakage [PIN = -10] (dBm) 0 -15 -20 -25 -30 -35 -40 -45 -50 -5 -10 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC -15 -20 -25 -30 -35 -40 -45 -50 700 750 800 850 900 950 700 750 RF Freq (MHz) RF-IF Leakage vs. LO Level 900 950 0 -5 -10 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC -10 3 X 3 Rejection [PIN = -10] (dBc) RF to IF leakage [PIN = -10] (dBm) 850 3RF X 3LO Rejection vs. TCASE 0 -15 -20 -25 -30 -35 -40 -45 -20 -30 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC -40 -50 -60 -70 -80 -90 -100 -50 650 700 750 800 850 900 950 700 750 RF Freq (MHz) 0 -10 25 degC - 0 dBm - 5.25 V - STD 25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD 25 degC - 0 dBm - 4.75 V - LC 3 X 3 Rejection [PIN = -10] (dBc) 0 -30 850 900 950 3RF X 3LO Rejection vs. LO Level -10 -20 800 RF Freq (MHz) 3RF X 3LO Rejection vs. VCC 3 X 3 Rejection [PIN = -10] (dBc) 800 RF Freq (MHz) -40 -50 -60 -70 -80 -90 -100 -20 -30 25 degC - 6 dBm - 5.00 V - STD 25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -6 dBm - 5.00 V - STD 25 degC - -6 dBm - 5.00 V - LC -40 -50 -60 -70 -80 -90 -100 700 750 800 850 900 950 700 RF Freq (MHz) IDT Zero-DistortionTM Mixer 750 800 850 900 950 RF Freq (MHz) 14 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [400 MHz Bands see modifications on p. 25 ] (-10-) Gain vs. LO Level (130 MHz IF) 11 11 10 10 9 9 Gain (dB) Gain (dB) Gain vs. TCASE (130 MHz IF) 8 7 6 5 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 8 7 6 5 4 25 degC - 3 dBm - 5.00 V - STD 25 degC - 3 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD 25 degC - -3 dBm - 5.00 V - LC 4 410 430 450 470 490 410 430 RF Freq (MHz) 45 45 40 40 35 30 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 490 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 35 30 25 20 25 degC - 3 dBm - 5.00 V - STD 25 degC - 3 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD 25 degC - -3 dBm - 5.00 V - LC 20 410 430 450 470 490 410 430 P1dB vs. LO Level (70 MHz IF) 14 14 13 13 Input P1dB (dBm) 15 12 11 10 9 8 6 5 410 25 degC - 3 dBm - 5.00 V - STD 25 degC - 3 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD 25 degC - -3 dBm - 5.00 V - LC 430 450 490 470 12 11 10 9 8 7 6 5 410 490 RF Freq (MHz) IDT Zero-DistortionTM Mixer 470 P1dB vs. LO Level (130 MHz IF) 15 7 450 RF Freq (MHz) RF Freq (MHz) Input P1dB (dBm) 470 Output IP3 vs. LO Level (130 MHz IF) Output IP3 (dBm) Output IP3 (dBm) Output IP3 vs. TCASE (130 MHz IF) 25 450 RF Freq (MHz) 25 degC - 3 dBm - 5.00 V - STD 25 degC - 3 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD 25 degC - -3 dBm - 5.00 V - LC 430 450 470 490 RF Freq (MHz) 15 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [400 MHz Bands see modifications on p. 25 ] (-11-) 2RF x 2LO vs. LO Level (130 MHz IF) 0 0 -10 -10 -20 -30 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 2 X 2 Rejection [PIN = -10] (dBc) 2 X 2 Rejection [PIN = -10] (dBc) 2RF x 2LO vs. TCASE (130 MHz IF) -40 -50 -60 -70 -80 -90 -20 -30 25 degC - 3 dBm - 5.00 V - STD 25 degC - 3 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD 25 degC - -3 dBm - 5.00 V - LC -40 -50 -60 -70 -80 -90 -100 -100 410 430 450 470 410 490 430 RF Freq (MHz) 0.400 0.400 0.380 0.380 0.360 0.360 0.340 0.300 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 0.280 0.320 25 degC - 3 dBm - 5.00 V - STD 25 degC - 3 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD 25 degC - -3 dBm - 5.00 V - LC 0.300 0.280 0.260 0.240 0.240 0.220 0.220 0.200 0.200 430 450 470 490 410 430 RF Freq (MHz) 450 470 490 RF Freq (MHz) LO to IF Leakage vs. TCASE (130 MHz IF) LO to IF Leakage vs. LO Level (130 MHz IF) 0 0 -5 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC -5 -10 LO to IF leakage (dBm) -10 LO to IF leakage (dBm) 490 0.340 0.260 410 470 ICC vs. LO Level (130 MHz IF) Total ICC (Amps) Total ICC (Amps) ICC vs. TCASE (130 MHz IF) 0.320 450 RF Freq (MHz) -15 -20 -25 -30 -35 -40 -45 25 degC - 3 dBm - 5.00 V - STD 25 degC - 3 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD 25 degC - -3 dBm - 5.00 V - LC -15 -20 -25 -30 -35 -40 -45 -50 -50 410 430 450 470 490 410 RF Freq (MHz) IDT Zero-DistortionTM Mixer 430 450 470 490 RF Freq (MHz) 16 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [400 MHz Bands see modifications on p. 25 ] (-12-) RF to IF Leakage vs. TCASE (130 MHz IF) RF to IF Leakage vs. LO Level (130 MHz IF) 0 0 -10 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC -5 RF to IF leakage [PIN = -10] (dBm) RF to IF leakage [PIN = -10] (dBm) -5 -15 -20 -25 -30 -35 -40 -45 -50 410 430 450 470 -10 25 degC - 3 dBm - 5.00 V - STD 25 degC - 3 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD 25 degC - -3 dBm - 5.00 V - LC -15 -20 -25 -30 -35 -40 -45 -50 490 410 430 450 RF Freq (MHz) 3RF x 3LO rejection vs. TCASE (130 MHz IF) 490 3RF x 3LO rejection vs. LO Level (130 MHz IF) 0 0 -10 -10 -20 -30 -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD 100 degC - 0 dBm - 5.00 V - LC 3 X 3 Rejection [PIN = -10] (dBc) 3 X 3 Rejection [PIN = -10] (dBc) 470 RF Freq (MHz) -40 -50 -60 -70 -80 -90 -100 410 430 450 470 -20 -30 25 degC - 3 dBm - 5.00 V - STD 25 degC - 3 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD 25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD 25 degC - -3 dBm - 5.00 V - LC -40 -50 -60 -70 -80 -90 -100 490 410 RF Freq (MHz) 430 450 470 490 RF Freq (MHz) Noise Figure (TCASE = 25C) Channel Isolation vs. LO level (130 MHz IF) 13.0 70 12.0 60 Noise Figure (dB) ChA to ChB Isolation (dBc) 65 55 50 45 40 35 30 -40 degC - 3 dBm - 5.00 V - STD -40 degC - 3 dBm - 5.00 V - LC -40 degC - 0 dBm - 5.00 V - STD -40 degC - 0 dBm - 5.00 V - LC -40 degC - -3 dBm - 5.00 V - STD -40 degC - -3 dBm - 5.00 V - LC 11.0 10.0 9.0 ChA STD mode ChA LC mode ChB STD mode ChB LC mode 25 20 410 430 450 470 8.0 490 400 RF Freq (MHz) IDT Zero-DistortionTM Mixer 420 440 460 480 500 RF Freq (MHz) 17 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [General] (-13-) EVkit IF Port Match (TA = 25C) 5RF X -4LO Rejection (IF = 190M, STD Mode) 0 IF Return Loss (dB) -5 ChA LC mode ChB LC mode ChA STD mode ChB STD mode 5 X -4 Rejection [PIN = +5] (dBc) -60 -10 -15 -20 -65 -70 -40 degC - ChA -40 degC - ChB 25 degC - ChA 25 degC - ChB 100 degC - ChA 100 degC - ChB -75 -80 -85 -90 -95 -100 -105 -25 100 200 300 400 500 -110 600 838 IF Freq (MHz) 898 VIF 10 0.1 8 0.0 6 -0.1 4 -0.2 2 VIF Out (Volts) 0.2 908 918 100 150 200 VSTBY 0.2 10 0.1 8 0.0 6 -0.1 4 -0.2 2 0 -0.3 0 -0.3 50 888 12 VSTBY STBY Logic Pin (Volts) VIF Out (Volts) 878 0.3 12 0 868 Settling Time (STBY -> VIH) 0.3 -50 858 RF Freq (MHz) Settling Time (STBY -> VIL) VIF 848 -50 250 STBY Logic Pin (Volts) 0 0 50 100 150 Time (nsec) Time (nsec) EVkit RF Port Match (TA = 25C) EVkit LO Port Match (TA = 25C, PMEAS = 0 dBm) 0 0 LO main STD LO main LC LO alt STD LO alt LC -5 RF Return Loss (dB) LO Port Return Loss (dB) -5 -10 -15 -20 -25 -30 -35 ChA LC mode ChB LC mode ChA STD mode ChB STD mode -10 -15 -20 -40 -45 -25 -50 0.50 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 RF Freq (GHz) LO Freq (GHz) IDT Zero-DistortionTM Mixer 18 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TYPICAL OPERATING CONDITIONS [General] (-14-) IP3O vs. PIN (TA = 25C, Freq = 850 MHz, IF = 200 MHz) 50 50 45 45 Output IP3 (dBm) Output IP3 (dBm) IP3O vs. ∆f (TA = 25C, Freq = 850 MHz, IF = 200 MHz) 40 35 30 STD 40 35 30 LC STD 25 25 20 20 0.8 2.8 4.8 6.8 8.8 10.8 12.8 -14 14.8 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 Input Power (dBm/Tone) Tone Spacing (MHz) TC4-1T Transformer Loss EVkit Input RF Trace Loss (TA = 25C) 0.0 0.0 -0.2 TC4-1T Transformer Loss (dB) RFA & RFB input trace loss (dB) LC -0.1 -0.2 -0.3 -0.4 -0.6 -0.8 See Mixer Device Gain plots. This Data is used to de-embed the EVKit measured data -1.0 -1.2 -40C +25C +100C -1.4 -0.4 650 700 750 800 850 900 4.0E+07 950 8.0E+07 1.2E+08 1.6E+08 2.0E+08 2.4E+08 2.8E+08 3.2E+08 3.6E+08 4.0E+08 Frequency (Hz) RF Freq (MHz) Gain Distribution (FRF = 915 MHz, LC mode, N = 1598) IP3O Distribution (FRF = 850 MHz, LC mode, N = 1598) 40% 25% Channel B Channel B 35% Channel A Channel A 20% Percentage Percentage 30% 15% 10% 25% 20% 15% 10% 5% 5% 0% 0% Gain Bin (dB) IP3O Bin (dBm) IDT Zero-DistortionTM Mixer 19 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI PACKAGE DRAWING (6X6 QFN) IDT Zero-DistortionTM Mixer 20 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI PINOUTS Please Note! Black Text denotes recommended external connection Red Text denotes internal Function or Connection - Only connect to one LO feed - Choose Either Pin 19 or Pin 27 - Do not connect the unused LO pin to ensure good LO return loss - DB GND = Downbonded to Paddle - Internal NC = Pin not connected LO2_ADJ GND [DB GND] 4 VCC NC [internal NC] NC [internal NC] 3 IF_A- GND [DB GND] IF_A+ 2 NC [internal NC] GND [RFA_rtn] IF_BiasA 1 VCC RF_A 36 35 34 33 32 31 30 29 28 B I A S C T R L 27 LO_in_alt 26 GND [internal NC] 25 GND [LCMODE] 24 GND [DB GND] 23 LO_SW [internal NC] VCC GND [RFB_rtn] 8 20 GND [LO_rtn] RF_B 9 19 LO_in IDT Zero-DistortionTM Mixer 10 11 12 13 14 15 16 17 18 GND [DB GND] 21 LO1_ADJ 7 VCC GND [DB GND] NC [internal NC] GND [STBY] IF_B- 22 IF_B+ 6 NC [internal NC] NC [internal NC] IF_BiasB 5 VCC GND [DB GND] 21 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI PIN DESCRIPTIONS Pin Name Function 1 RF_A Main Channel RF Input. Internally matched to 50Ω. DO NOT apply DC to these pins 2, 8, 20 RF_Artn, RF_Brtn, LO_rtn Transformer Ground Returns. Ground these pins. GND Ground these pins. 3, 5, 7, 18, 24, 28 4, 6, 12, 15, 31, 23, 26, 34 10, 16, 21, 30, 36 N.C. VCC 9 RF_B 11 IF_BiasB 13, 14 IFB+, IFB- 17 LO1_ADJ 19, 27 LO_in LO_in_alt 25 LC_MODE 22 STBY 29 LO2_ADJ 32, 33 IFA-, IFA+ 35 IF_BiasA — EP IDT Zero-DistortionTM Mixer No Connection. Not internally connected. OK to connect to Vcc. OK to connect to GND Power Supply. Bypass to GND with capacitors shown in the Typical Application Circuit as close as possible to pin. Diversity Channel RF Input. Internally matched to 50Ω Connect the specified resistor from this pin to ground to set the bias for the Diversity IF amplifier. This is NOT a current set resistor Diversity Mixer Differential IF Output. Connect pullup inductors from each of these pins to VCC (see the Typical Application Circuit). Connect the specified resistor for either Standard or LC mode from this pin to ground to set the LO common buffer Icc Local Oscillator Input. Connect the LO to this port through the recommended coupling capacitor. Note that you can only drive one LO port at a time. Remove the series capacitor from the unused port. Low_Current Mode. Set this pin to low or ground for LC mode. Set to high or No-Connect for Standard mode. There is an internal pull-up resistor. STBY Mode. Pull this pin high for Standby mode (~20 mA). Pull low or Ground for normal Operation Connect the specified resistor for either Standard or LC mode from this pin to ground to set the LO drive buffers Icc Main Mixer Differential IF Output. Connect pullup inductors from each of these pins to VCC (see the Typical Application Circuit). Connect the specified resistor from this pin to ground to set the bias for the Main IF amplifier. This is NOT a current set resistor Exposed Pad. Internally connected to GND. Solder this exposed pad to a PCB pad that uses multiple ground vias to provide heat transfer out of the device into the PCB ground planes. These multiple via grounds are also required to achieve the noted RF performance. 22 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI EVKIT SCHEMATIC C1 J2 4:1 Balun C2 Vcc J1 C4 Vcc C3 L2 L1 T1 Vcc Vcc C6 R15 R16 C5 Vcc R17 R18 J3 GND LO2_ADJ VCC NC IF_A- IF_A+ NC VCC IF_BiasA R9 R8 C7 JP J4 36 C8 35 34 33 32 31 30 29 28 RF_A 1 27 RF_A rtn 2 26 B I A S GND 3 NC 25 4 24 C T R L GND 5 NC 23 6 22 7 21 8 20 9 19 GND LO_in_alt JP NC LCMODE GND R10 NC STBY VCC C9 RF_B rtn LO_rtn Vcc RF_B J5 LO_in C11 J6 16 17 NC C12 Vcc 18 GND 15 LO1_ADJ 14 VCC 13 IF_B- 12 IF_B+ 11 NC VCC 10 IF_BiasB C10 R14 R13 R12 R11 C13 Vcc L3 T2 J7 L4 C14 Vcc C15 4:1 Balun C16 IDT Zero-DistortionTM Mixer 23 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI EVKIT PICTURE/LAYOUT/OPERATION Outer Position for STD Mode (R15, R17) Inner Position for LC Mode (R16, R18) Install Jumper for LC Mode Remove Jumper for STD Mode Alternate LO Port: Must remove C11 and Install C7 to use Install Jumper for Mixer Operation Remove Jumper to Turn Mixer Off Outer Position for STD Mode (R11, R13) IDT Zero-DistortionTM Mixer Inner Position for LC Mode (R12, R14) 24 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI EVKIT BOM Default BOM: For Standard Mode, Open the LCMODE jumper in conjunction with positioning the 4 dual jumpers to select the resistors in red. For Low Current Mode close the LCMODE jumper in conjunction with positioning the 4 dual jumpers to select the resistors in blue. F1102 BOM Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Value 10nF 1000pF 150pF 9 pF 10uF Header 2 Pin Header 3 Pin SMA_END_LAUNCH SMA_END_LAUNCH 270nH 27 62 91 180 1.91K 1.21K 47K 0 4:1 Balun F1102 PCB Size Desc Mfr. Part # Mfr. CAP CER 10000PF 16V 10% X7R 0402 GRM155R71C103KA01D 0402 MURATA CAP CER 1000PF 50V C0G 0402 GRM1555C1H102JA01D MURATA 0402 CAP CER 150PF 50V C0G 0402 GRM1555C1H151JA01D MURATA 0402 Note: C7 and C11 cannot be installed together. C7 for Pin27 LO feed. C11 for Pin19 LO feed 0402 CAP CER 10UF 6.3V X5R 0603 GRM188R60J106ME47D 0603 MURATA CONN HEADER VERT SGL 2POS GOLD 961102-6404-AR 3M TH 2 CONN HEADER VERT SGL 3POS GOLD 961103-6404-AR 3M TH 3 SMA_END_LAUNCH (Small) 142-0711-821 Emerson Johnson .062 SMA_END_LAUNCH (Big) 142-0701-851 Emerson Johnson .062 0805CS (2012) Ceramic Chip Inductor 0805CS-271XJLB 0805 COILCRAFT RES 27 OHM 1/10W 1% 0402 SMD ERJ-2RKF27R0X Panasonic 0402 RES 62.0 OHM 1/10W 1% 0402 SMD ERJ-2RKF62R0X Panasonic 0402 RES 91.0 OHM 1/10W 1% 0402 SMD ERJ-2RKF91R0X Panasonic 0402 RES 180 OHM 1/10W 1% 0402 SMD ERJ-2RKF1800X 0402 Panasonic RES 1.91K OHM 1/10W 1% 0402 SMD ERJ-2RKF1911X Panasonic 0402 RES 1.21K OHM 1/10W 1% 0402 SMD ERJ-2RKF1211X Panasonic 0402 RES 47.0K OHM 1/16W 1% 0402 SMD RC0402FR-0747KL Yageo 0402 RES 0.0 OHM 1/10W 0402 SMD ERJ-2GE0R00X Panasonic 0402 TC4-1TG2+ Mini Circuits SM-22 4:1 Center Tap Balun F1102NBGI QFN-36 Diversity Downconverter (400 - 1000 MHz) IDT EV Kit Part Reference C1,5,6,9,12,13,16 C2,3,14,15 C8,10,11 C7 C4 JP1,2,3 JP4,5,6,7 J1,2,7 J3,4,5,6 L1,2,3,4 R11,15 R12,16 R13 R14 R18 R17 R8,9 R1,2,3,4,5,6,7,10 T1,2 U1 F1102 EVkit Rev5 Qty 7 4 3 1 1 3 4 3 4 4 2 2 1 1 1 1 2 8 2 1 1 Modified BOM and EVKit (for 400 MHz bands): EVkit Modifications for High Side Injection 400 MHz operation (see TOCs on pages 15 – 17) Scrape resist from ground and add shunt 8 pF Replace C8 and C10 with 18 pF Scrape resist from ground and add shunt 1.8 pF Replace C11 with 6.8 pF IDT Zero-DistortionTM Mixer 25 RevO, August 2012 DATASHEET RF to IF Dual Downconverting Mixer 400 – 1000 MHz F1102NBGI TOPMARKINGS IDTF1102 NBGI YA1208A Part Number Date Code: [xxYYWWx] (Work Week 8 of 2012) Q21A029M ● IDT Zero-DistortionTM Mixer Lot Code 26 NOTE: Production Devices are DateCode 1208 or later. RevO, August 2012