TI1 LMC7221AIM5 Lmc7221 tiny cmos comparator with rail-to-rail input and open drain output Datasheet

LMC7221
www.ti.com
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
LMC7221 Tiny CMOS Comparator with Rail-To-Rail Input and Open Drain Output
Check for Samples: LMC7221
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
The LM7221 is a micropower CMOS comparator
available in the space saving 5-Pin SOT-23 package.
This makes this comparator ideal for space and
weight critical designs. The LMC7221 is also
available in the 8-Pin SOIC package. The LMC7221
is supplied in two offset voltage grades, 5 mV and 15
mV.
1
2
Tiny 5-Pin SOT-23 package saves space
Package is less than 1.43 mm thick
Ensured specs at 2.7V, 5V, 15V supplies
Typical supply current 7 μA at 5V
Response time of 4 μs at 5V
LMC7221—open drain output
Input common-mode range beyond V− and V+
Low input current
APPLICATIONS
•
•
•
•
•
•
•
Mixed voltage battery powered products
Notebooks and PDAs
PCMCIA cards
Mobile communications
Alarm and security circuits
Driving low current LEDs
Direct sensor interface
The open drain output can be pulled up with a
resistor to a voltage which can be higher or lower
than the supply voltage—this makes the part useful
for mixed voltage systems.
For a tiny comparator with a push-pull output, please
see the LMC7211 datasheet.
Connection Diagram
8-Pin SOIC - Top View
Figure 1. See Package Number D0008A
5-Pin SOT-23 - Top View
Figure 2. See Package Number DBV0005A
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
LMC7221
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
Absolute Maximum Ratings
ESD Tolerance
www.ti.com
(1)
(2)
2 kV
Differential Input Voltage
V+ +0.3V, V− −0.3V
Voltage at Input
V+ +0.3V, V− −0.3V
Voltage at Output Pin
+
15V
−
16V
(3)
±5 mA
Supply Voltage (V –V )
Current at Input Pin
Current at Output Pin (4)
(5)
±30 mA
Current at Power Supply Pin
40 mA
Lead Temperature (soldering, 10 sec.)
260°C
Junction Temperature
(1)
(6)
150°C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics.
Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of
JEDEC)Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
All limits are specified by testing or statistical analysis.
Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of ±30 mA may adversely affect reliability.
Limiting input pin current is only necessary for input voltages which exceed the absolute maximum input voltage rating.
The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board.
(2)
(3)
(4)
(5)
(6)
Operating Ratings
(1)
2.7 ≤ VCC ≤ 15V
Supply Voltage
Temperature Range
(2)
−40°C to +85°C
LMC7221AI, LMC7221BI
Thermal Resistance (θJA)
8-Pin SOIC
180°C/W
5-Pin SOT-23
325°C/W
(1)
(2)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics.
The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) – TA)/ θJA. All numbers apply for packages soldered directly onto a PC Board.
2.7V Electrical Characteristics
Unless otherwise specified, all limits ensured for TJ = 25°C, V+ = 2.7V, V− = 0V, VCM = VO = V+/2. Boldface limits apply at the
temperature extremes.
Parameter
VOS
Test Conditions
Input Offset Voltage
TCVOS
Input Offset Voltage
Temperature Drift
Input Offset Voltage Average
Drift
(3)
IOS
Input Offset Current
CMRR
Common Mode Rejection Ratio
0V ≤ VCM ≤ 2.7V
PSRR
Power Supply Rejection Ratio
2.7V ≤ V+ ≤ 15V
2
LMC7221BI
Limit (2)
3
5
15
mV
8
18
max
3.3
Input Current
(2)
(3)
LMC7221AI
Limit (2)
1.0
IB
(1)
Typ (1)
Units
μV/°C
μV/Month
0.04
pA
0.02
pA
75
dB
80
dB
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
All limits are specified by testing or statistical analysis.
CL includes the probe and test jig capacitance.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
LMC7221
www.ti.com
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
2.7V Electrical Characteristics (continued)
Unless otherwise specified, all limits ensured for TJ = 25°C, V+ = 2.7V, V− = 0V, VCM = VO = V+/2. Boldface limits apply at the
temperature extremes.
Parameter
AV
Voltage Gain
CMVR
Input Common-Mode Voltage
Range
VOL
Output Voltage Low
IS
Supply Current
Test Conditions
Typ (1)
LMC7221AI
Limit (2)
LMC7221BI
Limit (2)
2.9
2.9
V
2.7
2.7
min
−0.2
−0.2
V
0.0
0.0
max
0.3
0.3
V
0.4
0.4
max
12
12
μA
14
14
max
100
CMRR > 55 dB
3.0
CMRR > 55 dB
−0.3
ILOAD = 2.5 mA
0.2
VOUT = Low
7
Units
dB
5.0V and 15.0V Electrical Characteristics
Unless otherwise specified, all limits ensured for TJ = 25°C, V+ = 5.0V and 15V, V− = 0V, VCM = VO = V+/2. Boldface limits
apply at the temperature extremes.
Parameter
VOS
Test Conditions
Input Offset Voltage
TCVOS
Input Offset Voltage Temperature V+ = 5V
Drift
V+ = 15V
Input Offset Voltage Average Drift V+ = 5V
LMC7221AI
Limit (2)
LMC7221BI
Limit (2)
3
5
15
mV
8
18
max
1.0
(3)
Units
μV/°C
4.0
(3)
V+ = 15V
Typ (1)
3.3
μV/Month
4.0
IB
Input Current
0.04
pA
IOS
Input Offset Current
0.02
pA
CMRR
Common Mode Rejection Ration
75
dB
V = 15.0V
82
dB
5V ≤ V+ ≤ 10V
80
dB
V+ = 5.0V
+
PSRR
Power Supply Rejection Ratio
AV
Voltage Gain
CMVR
Input Common-Mode Voltage
Range
VOL
IS
(1)
(2)
(3)
Output Voltage Low
Supply Current
100
dB
V+ = 5.0V
CMRR > 55 dB
5.3
5.2
V+ = 5.0V
CMRR > 55 dB
−0.3
V+ = 15.0V
CMRR > 55 dB
15.3
V+ = 15.0V
CMRR > 55 dB
5.2
V
5.0
5.0
min
−0.2
−0.2
V
0.0
0.0
max
15.2
15.2
V
15.0
15.0
min
−0.3
−0.2
−0.2
V
0.0
0.0
max
V+ = 5V
ILOAD = 5 mA
0.2
0.40
0.40
mV
0.55
0.55
max
V+ = 15V
ILOAD = 5 mA
0.2
0.40
0.40
mV
0.55
0.55
max
VOUT = Low
7
14
14
μA
18
18
max
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
All limits are specified by testing or statistical analysis.
CL includes the probe and test jig capacitance.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
3
LMC7221
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
5.0V and 15.0V Electrical Characteristics (continued)
Unless otherwise specified, all limits ensured for TJ = 25°C, V+ = 5.0V and 15V, V− = 0V, VCM = VO = V+/2. Boldface limits
apply at the temperature extremes.
Parameter
ISC
(4)
Short Circuit Current
Test Conditions
Sinking
LMC7221AI
Limit (2)
Typ (1)
(4)
LMC7221BI
Limit (2)
45
Units
mA
Limiting input pin current is only necessary for input voltages which exceed the absolute maximum input voltage rating.
Leakage Characteristics
TJ = 25°C
Parameter
ILEAKAGE
(1)
(2)
Output Leakage Current
Test Conditions
Typ (1)
LMC7221AI
Limit (2)
LMC7221BI
Limit (2)
Units
0.1
500
500
nA
V+ = 2.7V
VIN(+) = 0.5V
VIN(−) = 0V
VOUT = 15V
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
All limits are specified by testing or statistical analysis.
AC Electrical Characteristics
Unless otherwise specified, all limits ensured for TJ = 25°C, V+ = 5V, V− = 0V, VCM = VO = V+/2. Boldface limits apply at the
temperature extreme.
Parameter
trise
Rise Time
Test Conditions
Typ (1)
f = 10 kHz, CL = 50 pF, (3)
Overdrive = 10 mV, 5 kΩ Pullup
(3)
0.3
tfall
Fall Time
f = 10 kHz, CL = 50 pF,
Overdrive = 10 mV, 5 kΩ Pullup
0.3
tPHL
Propagation Delay
(High to Low) (4)
f = 10 kHz, CL = 50 pF,
5 kΩ Pullup (3)
10 mV
10
100 mV
4
10 mV
10
100 mV
4
10 mV
6
100 mV
4
10 mV
7
100 mV
4
V+ = 2.7V, f = 10 kHz,
CL = 50 pF, 5 kΩ Pullup
tPLH
Propagation Delay
(Low to High) (4)
f = 10 kHz, CL = 50 pF,
5 kΩ Pullup (3)
V+ = 2.7V, f = 10 kHz,
CL = 50 pF, 5 kΩ Pullup
(1)
(2)
(3)
(4)
4
(3)
(3)
LMC7221AI
Limit (2)
LMC7221BI
Limit (2)
Units
μs
μs
μs
μs
μs
μs
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
All limits are specified by testing or statistical analysis.
Do not short circuit the output to V+ when V+ is greater than 12V or reliability will be adversely affected.
Input offset voltage average drift is calculated by dividing the accelerated operating life VOS drift by the equivalent operational time. This
represents worst case input conditions and includes the first 30 days of drift.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
LMC7221
www.ti.com
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
Typical Performance Characteristics
Supply Current
vs.
Supply Voltage
Supply Current
vs.
Temperature while Sinking
Figure 3.
Figure 4.
Output Sinking Current
vs.
Supply Voltage
Output Sinking Current
vs.
Output Voltage @ 5V
Figure 5.
Figure 6.
Output Sinking Current
vs.
Output Voltage @ 15V
Response Time for Various Input Overdrives −tPHL
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
5
LMC7221
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
6
Response Time
vs.
Various Input Overdrives −tPHL
Response Time
vs
Various Input Overdrives −tPHL
Figure 9.
Figure 10.
Input Bias Current
vs.
Common Mode Voltage
Input Bias Current
vs.
Common Mode Voltage
Figure 11.
Figure 12.
Input Bias Current
vs.
Common Mode Voltage
Input Bias Current
vs.
Temperature
Figure 13.
Figure 14.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
LMC7221
www.ti.com
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Leakage Current
vs.
Supply Voltage
Figure 15.
APPLICATION INFORMATION
BENEFITS OF THE LMC7221 TINY COMPARATOR
Size
The small footprint of the 5-Pin SOT-23 packaged Tiny Comparator, (0.120 x 0.118 inches, 3.05 x 3.00 mm)
saves space on printed circuit boards, and enable the design of smaller electronic products. Because they are
easier to carry, many customers prefer smaller and lighter products.
Height
The height (0.056 inches, 1.43 mm) of the Tiny Comparator makes it possible to use it in PCMCIA type III cards.
Simplified Board Layout
The Tiny Comparator can simplify board layout in several ways. First, by placing a comparator where
comparators are needed, instead of routing signals to a dual or quad device, long pc traces may be avoided.
By using multiple Tiny Comparators instead of duals or quads, complex signal routing and possibly crosstalk can
be reduced.
Low Supply Current
The typical 7 μA supply current of the LMC7221 extends battery life in portable applications, and may allow the
reduction of the size of batteries in some applications.
Wide Voltage Range
The LMC7221 is characterized at 15V, 5V and 2.7V. Performance data is provided at these popular voltages.
This wide voltage range makes the LMC7221 a good choice for devices where the voltage may vary over the life
of the batteries.
Digital Outputs Representing Signal Level
Comparators provide a high or low digital output depending on the voltage levels of the (+) and (−) inputs. This
makes comparators useful for interfacing analog signals to microprocessors and other digital circuits. The
LMC7221 can be thought of as a one-bit a/d converter.
Open Drain Output
The open drain output is like the open collector output of a logic gate. This makes the LMC7221 very useful for
mixed voltage systems.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
7
LMC7221
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Driving LEDs (Light Emitting Diodes)
With a 5 volt power supply, the LMC7221's output sinking current can drive small, high efficiency LEDs for
indicator and test point circuits. The small size of the Tiny package makes it easy to find space to add this
feature to even compact designs.
Input range to Beyond Rail to Rail
The input common mode range of the LMC7221 is slightly larger than the actual power supply range. This wide
input range means that the comparator can be used to sense signals close to the power supply rails. This wide
input range can make design easier by eliminating voltage dividers, amplifiers, and other front end circuits
previously used to match signals to the limited input range of earlier comparators. This is useful to power supply
monitoring circuits which need to sense their own power supply, and compare it to a reference voltage which is
close to the power supply voltage. The wide input range can also be useful for sensing the voltage drop across a
current sense resistor for battery chargers.
Zero Crossing Detector
Since the LMC7221's common mode input range extends below ground even when powered by a single positive
supply, it can be used with large input resistors as a zero crossing detector.
Low Input Currents and High Input Impedance
These characteristics allow the LMC7221 to be used to sense high impedance signals from sensors. They also
make it possible to use the LMC7221 in timing circuits built with large value resistors. This can reduce the power
dissipation of timing circuits. For very long timing circuits, using high value resistors can reduce the size and cost
of large value capacitors for the same R-C time constant.
Direct Sensor Interfacing
The wide input voltage range and high impedance of the LMC7221 may make it possible to directly interface to a
sensor without the use of amplifiers or bias circuits. In circuits with sensors which can produce outputs in the
tens to hundreds of millivolts, the LMC7221 can compare the sensor signal with an appropriately small reference
voltage. This may be done close to ground or the positive supply rail. Direct sensor interfacing may eliminate the
need for an amplifier for the sensor signal. Eliminating the amplifier can save cost, space, and design time.
LOW VOLTAGE OPERATION
Comparators are the common devices by which analog signals interface with digital circuits. The LMC7221 has
been designed to operate at supply voltages of 2.7V without sacrificing performance to meet the demands of 3V
digital systems.
At supply voltages of 2.7V, the common-mode voltage range extends 200 mV (ensured) below the negative
supply. This feature, in addition to the comparator being able to sense signals near the positive rail, is extremely
useful in low voltage applications.
Figure 16. Even at Low-Supply Voltage of 2.7V, an Input Signal which Exceeds the Supply Voltages
Produces No Phase Inversion at the Output
At V+ = 2.7V propagation delays are tPLH = 4 μs and tPHL = 4 μs with overdrives of 100 mV.
Please refer to the performance curves for more extensive characterization.
8
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
LMC7221
www.ti.com
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
OPEN DRAIN OUTPUT
Output Stage
Figure 17. Output Stage
Figure 17 shows the difference between push-pull output and open drain output.
Push pull outputs will have a conventional high or low digital output, the same as a logic gate. Low will be the
negative supply rail (usually ground) and high will be the positive supply rail.
This is useful if the chips you are interfacing to run on the same supply voltage as the comparator. An example
would be an all +5V system.
Open drain outputs will only pull low—for the high output they depend on an external pull-up resistor. This can
pull up to a voltage higher or lower than the comparator supply voltage. This voltage can be as high as 15V. This
makes the open drain parts useful in mixed voltage systems. An example would be where the comparator runs at
5V and the logic circuits are at 3.3V. The pull-up resistor would go to the 3.3V supply.
Open drain outputs are the CMOS equivalent of open collector outputs.
OUTPUT SHORT CIRCUIT CURRENT
The LMC7221 has short circuit protection of 40 mA. However, it is not designed to withstand continuous short
circuits, transient voltage or current spikes, or shorts to any voltage beyond the supplies. A resistor in series with
the output should reduce the effect of shorts. For outputs which send signals off PC boards additional protection
devices, such as diodes to the supply rails, and varistors may be used.
INPUT PROTECTION
If input signals are likely to exceed the common mode range of the LMC7221, or it is likely that signals may be
present when power is off, damage to the LMC7221 may occur. Large value (100 kΩ to MΩ) input resistors may
reduce the likelihood of damage by limiting the input currents. Since the LMC7221 has very low input leakage
currents, the effect on accuracy will be small. Additional protection may require the use of diodes, as shown in
Figure 18. Note that diode leakage current may affect accuracy during normal operation.
The R-C time constant of RIN and the diode capacitance may also slow response time.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
9
LMC7221
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
Figure 18.
LAYOUT CONSIDERATIONS
The LMC7221 is not an especially fast comparator, so high speed design practices are not required. The
LMC7221 is capable of operating with very high impedance inputs, so precautions should be taken to reduce
noise pickup with high impedance (∼ 100 kΩ and greater) designs and in electrically noisy environments.
Keeping high value resistors close to the LMC7221 and minimizing the size of the input nodes is a good practice.
With multilayer designs, try to avoid long loops which could act as inductors (coils). Sensors which are not close
to the comparator may need twisted pair or shielded connections to reduce noise.
PUSH-PULL OUTPUTS, DUAL VERSIONS
The LMC7211 is a comparator similar to the LMC7221, but with push-pull outputs which can source current.
The performance of the LMC7221 is available in a dual device. Please see the LMC6772 datasheet. For a dual
device with push-pull outputs, please see the LMC6762 datasheet.
Rail-to-Rail Input Low Power Comparators—
Push-Pull Output
LMC7221
5-Pin SOT-23, 8-Pin SOIC
Single
LMC6762
8-Pin SOIC
Dual
Open Drain Output
LMC7221
5-Pin SOT-23, 8-Pin SOIC
Single
LMC6772
8-Pin SOIC
Dual
ADDITIONAL 5-Pin SOT-23 TINY DEVICES
TI has additional parts available in the space saving SOT-23 Tiny package, including amplifiers, voltage
references, and voltage regulators, including the following:
LMC7101
1 MHz gain-bandwidth rail-to-rail input and output amplifier—high input impedance and high gain 700 μA typical
current 2.7V, 3V, 5V and 15V specifications.
LMC7111
Low power 50 kHz gain-bandwidth rail-to-rail input and output amplifier with 25 μA typical current specified at 2.7V,
3.0V, 3.3V, 5V and 10V.
LM7131
Tiny Video amp with 70 MHz gain bandwidth 3V, 5V and ±5V specifications.
LP2980
Micropower SOT 50 mA Ultra Low-Dropout Regulator.
LM4040
Precision micropower shunt voltage reference. Fixed voltages of 2.500V, 4.096V, 5.000V, 8.192V and 10.000V.
LM4041
Precision micropower shut voltage reference 1.225V and adjustable.
LM385
Low current voltage reference. Fixed Voltages of 1.2V and 2.5V.
10
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
LMC7221
www.ti.com
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
Contact your TI representative for the latest information.
SPICE MACROMODEL
A Spice Macromodel is available for the LMC7221 comparator on the TI Amplifier Macromodel disk. Contact your
TI representative to obtain the latest version.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
11
LMC7221
SNOS748E – SEPTEMBER 1999 – REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision D (March 2013) to Revision E
•
12
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 11
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LMC7221
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMC7221AIM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 85
LMC72
21AIM
LMC7221AIM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LMC72
21AIM
LMC7221AIM5
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 85
C01A
LMC7221AIM5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
C01A
LMC7221AIM5X
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 85
C01A
LMC7221AIM5X/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
C01A
LMC7221AIMX
NRND
SOIC
D
8
2500
TBD
Call TI
Call TI
-40 to 85
LMC72
21AIM
LMC7221AIMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LMC72
21AIM
LMC7221BIM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 85
LMC72
21BIM
LMC7221BIM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LMC72
21BIM
LMC7221BIM5
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 85
C01B
LMC7221BIM5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
C01B
LMC7221BIM5X
NRND
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
-40 to 85
C01B
LMC7221BIM5X/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
C01B
LMC7221BIMX
NRND
SOIC
D
8
2500
TBD
Call TI
Call TI
-40 to 85
LMC72
21BIM
LMC7221BIMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LMC72
21BIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LMC7221AIM5
SOT-23
DBV
5
1000
178.0
8.4
LMC7221AIM5/NOPB
SOT-23
DBV
5
1000
178.0
LMC7221AIM5X
SOT-23
DBV
5
3000
178.0
LMC7221AIM5X/NOPB
SOT-23
DBV
5
3000
LMC7221AIMX
SOIC
D
8
W
Pin1
(mm) Quadrant
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LMC7221AIMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LMC7221BIM5
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMC7221BIM5/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMC7221BIM5X
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMC7221BIM5X/NOPB
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LMC7221BIMX
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LMC7221BIMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
8-Apr-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMC7221AIM5
SOT-23
DBV
5
1000
210.0
185.0
35.0
LMC7221AIM5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LMC7221AIM5X
SOT-23
DBV
5
3000
210.0
185.0
35.0
LMC7221AIM5X/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LMC7221AIMX
SOIC
D
8
2500
367.0
367.0
35.0
LMC7221AIMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LMC7221BIM5
SOT-23
DBV
5
1000
210.0
185.0
35.0
LMC7221BIM5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LMC7221BIM5X
SOT-23
DBV
5
3000
210.0
185.0
35.0
LMC7221BIM5X/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LMC7221BIMX
SOIC
D
8
2500
367.0
367.0
35.0
LMC7221BIMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated