FERROXCUBE DATA A SH SHEET EET E64/10/50 Planar E cores and accessories Supersedes data of February 2002 2004 Sep 01 Ferroxcube Planar E cores and accessories E64/10/50 CORES Effective core parameters of a set of E cores handbook, halfpage SYMBOL PARAMETER VALUE Σ(I/A) core factor (C1) 0.156 mm−1 Ve effective volume 40700 mm3 Ie effective length 79.9 mm Ae effective area 519 mm2 Amin minimum area 519 mm2 m mass of core half ≈ 100 g 64.0 ±1.3 53.8 ±1.1 UNIT 10.2 ±0.2 5.1 ±0.13 10.2 ±0.13 R0.25 max. typ. 50.8 ±1 R0.64 ref. typ. R0.81 ref. typ. CBW415 Dimensions in mm. Fig.1 E64/10/50. Effective core parameters of an E/PLT combination SYMBOL PARAMETER VALUE UNIT Σ(I/A) core factor (C1) 0.136 mm−1 Ve effective volume 35500 mm3 Ie effective length 69.7 mm Ae effective area 519 mm2 Amin minimum area 519 mm2 m mass of plate ≈ 78 g handbook, halfpage 63.8 ±1.3 5.08 ±0.13 Ordering information for plates GRADE 50.3 ±1 TYPE NUMBER 3C90 PLT64/50/5-3C90 3C92 PLT64/50/5-3C92 3C93 PLT64/50/5-3C93 3C94 PLT64/50/5-3C94 3F3 PLT64/50/5-3F3 3F4 PLT64/50/5-3F4 CBW416 R0.64 ref. typ. Dimensions in mm. Fig.2 PLT 64/50/5. 2004 Sep 01 2 Ferroxcube Planar E cores and accessories E64/10/50 Core halves for use in combination with an E core AL measured in combination with a non-gapped core half, clamping force for AL measurements, 100 ±30 N, unless stated otherwise. GRADE 3C90 AL (nH) AIR GAP (µm) µe 630 ±3%(1) ≈ 78 ≈ 1100 ±3%(1) TYPE NUMBER E64/10/50-3C90-E630-E ≈ 124 ≈ 660 E64/10/50-3C90-E1000-E 1600 ±5% ≈ 199 ≈ 385 E64/10/50-3C90-A1600-E 2500 ±10% ≈ 310 ≈ 225 E64/10/50-3C90-A2500-E E64/10/50-3C90-A3150-E 1000 3150 ±10% ≈ 391 ≈ 170 14640 ±25% ≈ 1820 ≈0 E64/10/50-3C90 3C92 11200 ±25% ≈ 1390 ≈0 E64/10/50-3C92 3C93 13300 ±25% E64/10/50-3C93 3C94 3F3 3F4 ≈ 1650 ≈0 ±3%(1) ≈ 78 ≈ 1100 1000 ±3%(1) ≈ 124 ≈ 660 E64/10/50-3C94-E1000-E 1600 ±5% ≈ 199 ≈ 385 E64/10/50-3C94-A1600-E 2500 ±10% ≈ 310 ≈ 225 E64/10/50-3C94-A2500-E 3150 ±10% ≈ 391 ≈ 170 E64/10/50-3C94-A3150-E 14640 ±25% 630 E64/10/50-3C94-E630-E ≈ 1820 ≈0 ±3%(1) ≈ 78 ≈ 1100 1000 ±3%(1) ≈ 124 ≈ 660 E64/10/50-3F3-E1000-E 1600 ±5% ≈ 199 ≈ 385 E64/10/50-3F3-A1600-E 2500 ±10% ≈ 310 ≈ 225 E64/10/50-3F3-A2500-E 3150 ±10% ≈ 391 ≈ 170 E64/10/50-3F3-A3150-E 13300 ±25% 630 E64/10/50-3C94 E64/10/50-3F3-E630-E ≈ 1650 ≈0 ±3%(1) ≈ 78 ≈ 1100 1000 ±3%(1) ≈ 124 ≈ 660 E64/10/50-3F4-E1000-E 1600 ±5% ≈ 199 ≈ 385 E64/10/50-3F4-A1600-E 2500 ±10% ≈ 310 ≈ 225 E64/10/50-3F4-A2500-E 3150 ±10% ≈ 391 ≈ 170 E64/10/50-3F4-A3150-E 6960 ±25% ≈ 860 ≈0 630 E64/10/50-3F3 E64/10/50-3F4-E630-E E64/10/50-3F4 Note 1. Measured in combination with an equal-gapped core half, clamping force for AL measurements, 100 ±30 N. 2004 Sep 01 3 Ferroxcube Planar E cores and accessories E64/10/50 Core halves for use in combination with a plate (PLT) AL measured in combination with a plate (PLT), clamping force for AL measurements, 100 ±30 N. GRADE 3C90 AIR GAP (µm) AL (nH) µe 630 ±3% ≈ 78 ≈ 1100 1000 ±3% ≈ 124 ≈ 660 E64/10/50-3C90-A-1000-P 1600 ±5% ≈ 199 ≈ 385 E64/10/50-3C90-A-1600-P 2500 ±10% ≈ 310 ≈ 225 E64/10/50-3C90-A-2500-P 3150 ±10% ≈ 391 ≈ 170 E64/10/50-3C90-A-3150-P ≈ 1790 16540 ±25% TYPE NUMBER E64/10/50-3C90-A-630-P ≈0 E64/10/50-3C90 3C92 12700 ±25% ≈ 1370 ≈0 E64/10/50-3C92 3C93 15050 ±25% ≈ 1630 ≈0 E64/10/50-3C93 3C94 630 ±3% ≈ 78 ≈ 1100 1000 ±3% ≈ 124 ≈ 660 E64/10/50-3C94-A-1000-P 1600 ±5% ≈ 199 ≈ 385 E64/10/50-3C94-A-1600-P 2500 ±10% ≈ 310 ≈ 225 E64/10/50-3C94-A-2500-P 3150 ±10% ≈ 391 ≈ 170 E64/10/50-3C94-A-3150-P 16540 ±25% ≈ 1790 ≈0 630 ±3% ≈ 78 ≈ 1100 1000 ±3% ≈ 124 ≈ 660 E64/10/50-3F3-A-1000-P 1600 ±5% ≈ 199 ≈ 385 E64/10/50-3F3-A-1600-P 2500 ±10% ≈ 310 ≈ 225 E64/10/50-3F3-A-2500-P 3150 ±10% ≈ 391 ≈ 170 E64/10/50-3F3-A-3150-P 15050 ±25% ≈ 1630 ≈0 630 ±3% ≈ 78 ≈ 1100 1000 ±3% ≈ 124 ≈ 660 E64/10/50-3F4-A-1000-P 1600 ±5% ≈ 199 ≈ 385 E64/10/50-3F4-A-1600-P 2500 ±10% ≈ 310 ≈ 225 E64/10/50-3F4-A-2500-P 3150 ±10% ≈ 391 ≈ 170 E64/10/50-3F4-A-3150-P 7920 ±25% ≈ 860 ≈0 3F3 3F4 2004 Sep 01 4 E64/10/50-3C94-A-630-P E64/10/50-3C94 E64/10/50-3F3-A-630-P E64/10/50-3F3 E64/10/50-3F4-A-630-P E64/10/50-3F4 Ferroxcube Planar E cores and accessories E64/10/50 Properties of core sets under power conditions B (mT) at CORE LOSS (W) at H = 250 A/m; f = 10 kHz; T = 100 °C f = 100 kHz; ˆ = 100 mT; B T = 100 °C f = 100 kHz; ˆ = 200 mT; B T = 100 °C f = 400 kHz; ˆ = 50 mT; B T = 100 °C E+E64-3C90 ≥320 ≤ 4.8 − − E+PLT64-3C90 ≥320 ≤ 4.2 − − E+E64-3C92 ≥370 ≤ 3.6 ≤ 25 − E+PLT64-3C92 ≥370 ≤ 3.2 ≤ 23 − E+E64-3C93 ≥320 ≤ 3.6(1) ≤ 25(1) − E+PLT64-3C93 ≥320 ≤ 3.2(1) ≤ 23(1) − E+E64-3C94 ≥320 ≤ 3.6 ≤ 25 − E+PLT64-3C94 ≥320 ≤ 3.2 ≤ 23 − E+E64-3F3 ≥300 ≤ 4.8 − ≤ 7.8 E+PLT64-3F3 ≥300 ≤ 4.2 − ≤ 6.8 E+E64-3F4 ≥250 − − − E+PLT64-3F4 ≥250 − − − GRADE 1. Measured at 140 °C. Properties of core sets under power conditions (continued) B (mT) at CORE LOSS (W) at H = 250 A/m; f = 10 kHz; T = 100 °C f = 500 kHz; B̂ = 50 mT; T = 100 °C f = 500 kHz; B̂ = 100 mT; T = 100 °C f = 1 MHz; ˆ = 30 mT; B T = 100 °C f = 3 MHz; ˆ = 10 mT; B T = 100 °C E+E64-3C90 ≥320 − − − − E+PLT64-3C90 ≥320 − − − − E+E64-3C92 ≥370 − − − − E+PLT64-3C92 ≥370 − − − − E+E64-3C93 ≥320 − − − − E+PLT64-3C93 ≥320 − − − − E+E64-3C94 ≥320 − − − − E+PLT64-3C94 ≥320 − − − − E+E64-3F3 ≥300 − − − − E+PLT64-3F3 ≥300 − − − − E+E64-3F4 ≥250 − − ≤ 12 ≤ 20 E+PLT64-3F4 ≥250 − − ≤ 10.5 ≤ 17 GRADE 2004 Sep 01 5 Ferroxcube Planar E cores and accessories E64/10/50 DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS PRODUCT STATUS DEFINITIONS Preliminary specification Development This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. Design-in These products are recommended for new designs. Preferred These products are recommended for use in current designs and are available via our sales channels. Support These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 2004 Sep 01 6