EL7243
®
Data Sheet
May 13, 2005
Dual Input, High Speed, Dual Channel
CCD Driver
FN7286.1
Features
• Logic AND/NAND input
The EL7243 dual input, 2-channel driver achieves the same
excellent switching performance of the EL7212 family while
providing added flexibility. The power package makes this
part extremely well suited for high frequency and heavy
loads as in CCD applications. The 2-input logic and
configuration is applicable to numerous power MOSFET
drive circuits. As with other Elantec drivers, the EL7243 is
excellent for driving large capacitive loads with minimal delay
and switching times. “Shoot-thru” protection and latching
circuits can be implemented by simply “cross-coupling” the
2-channels.
• 3V and 5V Input compatible
• Clocking speeds up to 20MHz
• 20ns Switching/delay time
• 2A Peak drive
• Isolated drains
• Low output impedance
• Low quiescent current
• Wide operating voltage — 4.5V to 16V
• Pb-Free available (RoHS compliant)
Pinout
EL7243
(20-PIN THERMAL SOIC)
TOP VIEW
Applications
• CCD Drivers
• Short circuit protected switching
• Under-voltage shut-down circuits
• Switch-mode power supplies
• Motor controls
• Power MOSFET switching
• Switching capacitive loads
• Shoot-thru protection
• Latching drivers
Note 1: Pins 4–7 and 14–17 are electrically connected.
Note 2: Output pins must be tied together.
Ordering Information
Manufactured under U.S. Patent Nos. 5,334,883, #5,341,047
PACKAGE
TAPE &
REEL
PKG. DWG. #
EL7243CM
20-Pin SOIC
-
MDP0027
EL7243CM-T13
20-Pin SOIC
13”
MDP0027
EL7243CMZ
(See Note)
20-Pin SOIC
(Pb-free)
-
MDP0027
EL7243CMZ-T13
(See Note)
20-Pin SOIC
(Pb-free)
13”
MDP0027
PART NUMBER
NOTE: Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with
both SnPb and Pb-free soldering operations. Intersil Pb-free products
are MSL classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J STD-020.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-352-6832 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 1996, 2003, 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
EL7243
Absolute Maximum Ratings (TA = 25°C)
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C
Power Dissipation
20-pin “Batwing” SOIC . . . . . . . . . . . . . . . . . . . . . . .1500mW
Supply (V+ to Gnd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V
Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V above V+
Combined Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . .4A
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
PARAMETER
TA = 25°C, VDD = 15V unless otherwise specified
DESCRIPTION
TEST CONDITIONS
MIN
TYP
MAX
UNITS
INPUT
VIH
Logic “1” Input Voltage
IIH
Logic “1” Input Current
VIL
Logic “0” Input Voltage
IIL
Logic “0” Input Current
VHVS
Input Hysteresis
2.4
@VDD
V
0.1
@0V
0.1
10
µA
0.8
V
10
µA
0.3
V
OUTPUT
ROH
Pull-Up Resistance
IOUT = -100mA
3
6
Ω
ROL
Pull-Down Resistance
IOUT = +100mA
4
6
Ω
IPK
Peak Output Current
Source
Sink
2
2
IDC
Continuous Output Current
Source/Sink
IS
Power Supply Current
Inputs High
VS
Operating Voltage
A
200
mA
POWER SUPPLY
AC Electrical Specifications
PARAMETER
1
4.5
2.5
mA
16
V
MAX
UNITS
TA = 25°C, V = 15V unless otherwise specified
DESCRIPTION
TEST CONDITIONS
MIN
TYP
SWITCHING CHARACTERISTICS
tR
Rise Time
CL = 500pF
CL = 1000pF
10
20
ns
tF
Fall Time
CL = 500pF
CL = 1000pF
10
20
ns
tD-ON
Turn-On Delay Time
20
25
ns
tD-OFF
Turn-Off Delay Time
20
25
ns
2
EL7243
Timing Table
Standard Test Configuration
Pins 19, 20 connected to V+
Simplified Schematic
3
EL7243
Typical Performance Curves
Max Power/Derating Curves
Switch Threshold vs Supply Voltage
Peak Drive vs Supply Voltage
Input Current vs Voltage
Quiescent Supply Current
4
“ON” Resistance vs Supply Voltage
EL7243
Typical Performance Curves
(Continued)
Average Supply Current vs
Voltage and Frequency
Average Supply Current
vs Capacitive Load
Rise/Fall Time vs Load
Rise/Fall Time vs Supply Voltage
Rise/Fall Time vs Temperature
Propagation Delay vs Supply Voltage
Delay vs Temperature
5
EL7243
Applications Information
Typical CCD Configuration
EL7243 Macromodel
6
EL7243
EL7243 Macromodel
* EL7243 Macromodel
* Revision A, January 1996
* Connections
Gnd
*
|
Inp+
*
|
|
Inp*
|
|
|
out
*
|
|
|
|
VCC
.subckt M7243 1 2 3 8 10
V1 12 1 1.6
R1 13 15 1k
R2 14 15 5k
R5 11 12 100
C1 15 1 43.3pF
D1 14 13 dmod
X1 13 11 2 1 comp1
X2 16 12 15 1 comp1
V2 22 1 1.6
R6 23 25 1K
R7 24 25 5K
R8 21 22 100
C2 25 1 43.3pF
D2 24 23 dmod
X3 23 21 3 1 comp1
X4 26 25 22 1 comp1
X5 16 26 17 1 And-gate
sp 10 8 17 1 spmod
sn 8 1 17 1 snmod
g1 11 1 13 1 938u
g2 21 1 23 1 938u
.model dmod d
.model spmod vswitch ron=3 roff=2meg von=1 voff=1.5
.model snmod vswitch ron=4 roff=2meg von=3 voff=2
.ends M7243
* AND Gate Subcircuit*
.subckt And-gate inp1 inp2 out-AS Vss-A
el out-A Vss-A table {v(inp1)*v(inp2)} = (0, 3.2) (3.2, 0)
Rout-a out-a vss-a 10 meg
rinpa inp1 vss-a 10 meg
rinpb inp2 vss-a 10 meg
.ends and-gate
* Comparator Subcircuit *
.subckt comp1 out inp inm vss
el out vss table {(v(inp)-v(inm))*5000} = (0,0) (3.2, 3.2)
Rout out vss 10meg
Rinp inp vss 10meg
Rinm inm vss 10meg
.ends omp1
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
7