LINER LTC1664 Micropower quad 10-bit dac Datasheet

LTC1664
Micropower Quad
10-Bit DAC
Features
n
n
n
n
n
n
n
n
n
Description
Tiny: 4 DACs in the Board Space of an SO-8
Micropower: 59µA per DAC Plus
1µA Sleep Mode for Extended Battery Life
Wide 2.7V to 5.5V Supply Range
Rail-to-Rail Voltage Outputs Drive 1000pF
Reference Range Includes Supply for Ratiometric
0V to VCC Output
Reference Input Impedance is Code-Independent
—Eliminates External Reference Buffer
Individually Addressable DACs
Differential Nonlinearity: ≤ ±0.75LSB Max
Pin-Compatible Octal Version Available (LTC1660)
The LTC®1664 integrates four accurate, serially addressable
10-bit digital-to-analog converters (DACs) in a tiny 16-pin
narrow SSOP package. Each buffered DAC draws just 59µA
total supply current, yet is capable of supplying DC output
currents in excess of 5mA and reliably driving capacitive
loads of up to 1000pF. Sleep mode further reduces total
supply current to 1µA.
Linear Technology’s proprietary, inherently monotonic
voltage interpolation architecture provides excellent linearity while allowing for an exceptionally small external
form factor.
Ultralow supply current, power-saving sleep mode and
extremely compact size make the LTC1664 ideal for
battery-powered applications, while its ease of use, high
performance and wide supply range make it an excellent
choice as a general-purpose converter.
Applications
n
n
n
n
n
Mobile Communications
Remote Industrial Devices
Automatic Calibration for Manufacturing
Portable Battery-Powered Instruments
Trim/Adjust Applications
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Block Diagram
GND
VOUT A
1
2
16 VCC
10-BIT
DAC A
10-BIT
DAC D
5
Differential Nonlinearity (DNL)
1.0
VOUT D
VCC = 5V
0.8 VREF = 4.096V
0.6
0.4
3
10-BIT
DAC C
4
0.2
VOUT C
LSB
VOUT B
10-BIT
DAC B
0
–0.2
–0.4
REF
6
CS/LD
7
CONTROL
LOGIC
ADDRESS
DECODER
–0.6
11
CLR
10
DOUT
–0.8
–1.0
SCK
8
SHIFT REGISTER
9
0
256
512
CODE
768
1023
1664 G02
DIN
1664 BD
1664fa
1
LTC1664
Absolute Maximum Ratings
Pin Configuration
(Note 1)
TOP VIEW
VCC to GND............................................... – 0.3V to 7.5V
Logic Inputs to GND ................................ – 0.3V to 7.5V
VOUT A , VOUT B…VOUT D ,
REF to GND ................................. –0.3V to (VCC + 0.3V)
Maximum Junction Temperature........................... 125°C
Operating Temperature Range
LTC1664C................................................ 0°C to 70°C
LTC1664I............................................. –40°C to 85°C
Storage Temperature Range.................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
GND
1
16 VCC
VOUT A
2
15 NC
VOUT B
3
14 NC
VOUT C
4
13 NC
VOUT D
5
12 NC
REF
6
11 CLR
CS/LD
7
10 DOUT
SCK
8
9
GN PACKAGE
16-LEAD PLASTIC SSOP
DIN
N PACKAGE
16-LEAD PDIP
TJMAX = 125°C, θJA = 150°C/W (GN)
TJMAX = 125°C, θJA = 100°C/W (N)
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC1664CGN#PBF
LTC1664CGN#TRPBF
1664
16-Lead Plastic SSOP
0°C to 70°C
LTC1664CN#PBF
LTC1664CN#TRPBF
LTC1664CN
16-Lead PDIP
0°C to 70°C
LTC1664IGN#PBF
LTC1664IGN#TRPBF
1664I
16-Lead Plastic SSOP
–40°C to 85°C
LTC1664IN#PBF
LTC1664IN#TRPBF
LTC1664IN
16-Lead PDIP
–40°C to 85°C
LEAD BASED FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC1664CGN
LTC1664CGN#TR
1664
16-Lead Plastic SSOP
0°C to 70°C
LTC1664CN
LTC1664CN#TR
LTC1664CN
16-Lead PDIP
0°C to 70°C
LTC1664IGN
LTC1664IGN#TR
1664I
16-Lead Plastic SSOP
–40°C to 85°C
LTC1664IN
LTC1664IN#TR
LTC1664IN
16-Lead PDIP
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
1664fa
2
LTC1664
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 2.7V to 5.5V, VREF ≤ VCC, VOUT unloaded, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Accuracy
l
10
Bits
Monotonicity
(Notes 2, 4)
l
10
Bits
DNL
Differential Nonlinearity
(Notes 2, 4)
l
±0.2
±0.75
LSB
INL
Integral Nonlinearity
(Notes 2, 4)
l
±0.6
±2.5
LSB
VOS
Offset Error
(Note 7)
l
±10
±30
mV
l
±15
FSE
Full-Scale Error
l
±3
l
±30
µV/°C
0.18
LSB/V
Resolution
VOS Temperature Coefficient
VCC = 5V, VREF = 4.096V (Note 4)
Full-Scale Error Temperature Coefficient
PSR
Power Supply Rejection
VREF = 2.5V
µV/°C
±15
LSB
Reference Input
Input Voltage Range
Resistance
Not in Sleep Mode
l
0
l
70
Capacitance
IREF
Reference Current
Sleep Mode
VCC
130
kΩ
12
pF
0.001
l
V
1
µA
5.5
V
236
186
1
380
290
3
µA
µA
µA
Power Supply
VCC
Positive Supply Voltage
ICC
Supply Current
l
2.7
VCC = 5V (Note 3)
VCC = 3V (Note 3)
Sleep Mode (Note 3)
l
l
l
Short-Circuit Current Low
VOUT = 0V, VCC = 5.5V, VREF = 5.1V,
Code = 1023 (Note 9)
l
10
30
100
mA
Short-Circuit Current High
VOUT = VCC = 5.5V, VREF = 5.1V,
Code = 0 (Note 9)
l
10
27
120
mA
DC Performance
AC Performance
Voltage Output Slew Rate
Rising (Notes 4, 5)
Falling (Notes 4, 5)
Voltage Output Settling Time
Rising 0.1VFS to 0.9VFS ±0.5LSB (Notes 4, 5)
Falling 0.9VFS to 0.1VFS ± 0.5LSB (Notes 4, 5)
0.60
0.25
Capacitive Load Driving
V/µs
V/µs
6
19
µs
µs
1000
pF
Digital I/O
VIH
Digital Input High Voltage
VCC = 2.7V to 5.5V
VCC = 2.7V to 3.6V
l
l
VIL
Digital Input Low Voltage
VCC = 4.5V to 5.5V
VCC = 2.7V to 5.5V
l
l
VOH
Digital Output High Voltage
IOUT = –1mA, DOUT Only
l
VOL
Digital Output Low Voltage
IOUT = 1mA, DOUT Only
l
ILK
Digital Input Leakage
VIN = GND to VCC
l
CIN
Digital Input Capacitance
2.4
2.0
V
V
0.8
0.6
VCC – 1
V
V
V
0.05
2
0.4
V
±10
µA
pF
1664fa
3
LTC1664
Timing Characteristics
The l denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Figure 1)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VCC = 4.5V to 5.5V
t1
DIN Valid to SCK Setup
l
40
ns
t2
DIN Valid to SCK Hold
l
0
ns
t3
SCK High Time
(Note 6)
l
30
ns
t4
SCK Low Time
(Note 6)
l
30
ns
t5
CS/LD Pulse Width
(Note 6)
l
80
ns
t6
LSB SCK High to CS/LD High
(Note 6)
l
30
ns
t7
CS/LD Low to SCK High
(Note 6)
l
80
t8
DOUT Propagation Delay
CLOAD = 15pF (Note 6)
l
5
t9
SCK Low to CS/LD Low
(Note 6)
l
20
ns
t10
CLR Pulse Width
(Note 6)
l
100
ns
t11
CS/LD High to SCK Positive Edge
(Note 6)
l
30
ns
SCK Frequency
(Notes 6 and 8)
l
t1
DIN Valid to SCK Setup
(Note 6)
l
60
ns
t2
DIN Valid to SCK Hold
(Note 6)
l
0
ns
t3
SCK High Time
(Note 6)
l
50
ns
t4
SCK Low Time
(Note 6)
l
50
ns
t5
CS/LD Pulse Width
(Note 6)
l
100
ns
t6
LSB SCK High to CS/LD High
(Note 6)
l
50
ns
t7
CS/LD Low to SCK High
(Note 6)
l
100
t8
DOUT Propagation Delay
CLOAD = 15pF (Note 6)
l
5
t9
SCK Low to CS/LD Low
(Note 6)
l
30
ns
t10
CLR Pulse Width
(Note 6)
l
120
ns
t11
CS/LD High to SCK Positive Edge
(Note 6)
l
30
ns
SCK Frequency
(Notes 6 and 8)
l
ns
80
16.7
ns
MHz
VCC = 2.7V to 5.5V
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Nonlinearity and monotonicity are defined and tested at
VCC = 5V, VREF = 4.096V, from code 20 to code 1023. See the Rail-to-Rail
Output Considerations section.
Note 3: Digital inputs at 0V or VCC.
ns
150
10
ns
MHz
Note 4: Load is 10kΩ in parallel with 100pF.
Note 5: VCC = VREF = 5V.
Note 6: Guaranteed by design and not subject to test.
Note 7: Measured at code 20.
Note 8: If a continuous clock is used, CS/LD timing (t7 and t9) will limit
the maximum clock frequency to 5MHz at 4.5V to 5.5V (3.85MHz at 2.7V
to 5.5V).
Note 9: Any output shorted.
1664fa
4
LTC1664
Typical Performance Characteristics
Integral Nonlinearity (INL)
0.6
1.0
0.4
0.5
0.2
LSB
1.5
0
–0.2
–1.0
–0.4
–1.5
–0.6
– 2.0
–0.8
0
256
512
CODE
768
–1.0
1023
VREF = VCC
CODE = 1023
280
0
– 0.5
– 2.5
Supply Current vs Temperature
300
VCC = 5V
0.8 VREF = 4.096V
VCC = 5V
VREF = 4.096V
2.0
LSB
Differential Nonlinearity (DNL)
1.0
SUPPLY CURENT (µA)
2.5
260
VCC = 5.5V
240
VCC = 4.5V
220
VCC = 3.6V
200
VCC = 2.7V
180
0
256
512
CODE
768
160
–55 –35 –15
1023
1664 G02
5 25 45 65
TEMPERATURE (°C)
85 105 125
1664 G03
1664 G01
Load Regulation vs Output Current
VCC = VREF = 5V
CODE = 512
VCC = VREF = 3V
CODE = 512
2.0
1.5
1.0
1.0
0.5
0.5
∆VOUT (LSB)
∆VOUT (LSB)
1.5
0
–0.5
–1.0
5
10% TO
90% STEP
0
–0.5
3
2
–1.0
–1.5
SOURCE
–2.0
–2
–1
0
IOUT (mA)
1
–1.5
SINK
SOURCE
–2.0
1
2
–500
SINK
0
IOUT (µA)
2.0
1.9
2.8
1.7
VOUT (V)
VCC = 5.5V
VCC = 5V
2.5
2.4
2.3
2.2
SOURCE
2.0
–30
1.6
1.5
VCC = 3V
1.4
VCC = 2.7V
1.2
2.1
–20
–10
0
10
IOUT (mA)
SOURCE
1.0
20
30
1664 G07
–15 –12
100
0.8
0.6
0.4
0.2
1.1
SINK
80
ALL DIGITAL INPUTS
SHORTED TOGETHER
1.0
VCC = 3.6V
1.3
VCC = 4.5V
1.2
VREF = VCC
CODE = 512
1.8
2.6
40
60
TIME (µs)
Supply Current vs Logic Input
Voltage
Mid-Scale Output Voltage
vs Load Current
VREF = VCC
CODE = 512
2.7
20
1664 G06
SUPPLY CURRENT (mA)
2.9
0
1664 G05
Mid-Scale Output Voltage
vs Load Current
3.0
0
500
1664 G04
VOUT (V)
VCC = VREF = 5V
4
VOUT (V)
2.0
Large-Signal Step Response
Load Regulation vs Output Current
–8
SINK
–4
0
4
IOUT (mA)
8
12 15
1664 G08
0
0
1
2
3
4
LOGIC INPUT VOLTAGE (V)
5
1664 G09
1664fa
5
LTC1664
Typical Performance Characteristics
Minimum VOUT vs Load Current
(Output Sinking)
1400
1400
VCC = 5V
CODE = 0
1200
Minimum Supply Headroom vs
Load Current (Output Sourcing)
1000
800
VCC – VOUT (mV)
VOUT (mV)
1000
25°C
600
–55°C
400
125°C
800
25°C
600
–55°C
400
200
200
0
VREF = 4.096V
∆VOUT < 1LSB
CODE = 1023
1200
125°C
0
2
4
6
8
|IOUT| (mA) (SINKING)
10
1664 G10
0
0
2
4
6
8
|IOUT| (mA) (SOURCING)
10
1664 G11
Pin Functions
GND (Pin 1): System Ground.
VOUT A to VOUT D (Pins 2–5): DAC Analog Voltage Outputs.
The output range is:
DIN (Pin 9): Serial Interface Data Input. Data on the DIN
pin is shifted into the 16-bit register on the rising edge of
SCK. CMOS and TTL compatible.
REF (Pin 6): Reference Voltage Input. 0V ≤ VREF ≤ VCC.
DOUT (Pin 10): Serial Interface Data Output. Data appears
on DOUT 16 positive SCK edges after being applied to DIN.
May be tied to DIN of another serial device for daisy-chain
operation. CMOS and TTL compatible.
CS/LD (Pin 7): Serial Interface Chip Select/Load Input.
When CS/LD is low, SCK is enabled for shifting data on
DIN into the register. When CS/LD is pulled high, SCK is
disabled and data is loaded from the shift register into the
specified DAC register(s), updating the analog output(s).
CMOS and TTL compatible.
CLR (Pin 11): Asynchronous Clear Input. All internal shift
and DAC registers are cleared to zero at the falling edge of
the CLR signal, forcing the analog outputs to zero-scale.
CMOS and TTL compatible.
NC (Pins 12–15): Make no electrical connection to these
pins.
SCK (Pin 8): Serial Interface Clock Input. CMOS and TTL
compatible.
VCC (Pin 16): Supply Voltage Input. 2.7V ≤ VCC ≤ 5.5V.
 1023 
0 to 
V
 1024  REF
1664fa
6
LTC1664
Block Diagram
GND
1
VOUT A
2
10-BIT
DAC A
10-BIT
DAC D
5
VOUT D
VOUT B
3
10-BIT
DAC B
10-BIT
DAC C
4
VOUT C
11
CLR
10
DOUT
9
DIN
REF
6
CS/LD
7
SCK
8
16 VCC
CONTROL
LOGIC
ADDRESS
DECODER
SHIFT REGISTER
1664 BD
Timing Diagram
t1
t2
t3
t6
t4
SCK
t9
t11
DIN
A3
t5
A1
A2
X1
X0
t7
CS/LD
t8
DOUT
A3
A2
A1
X1
X0
A3
1664 F01
Figure 1
1664fa
7
LTC1664
Operation
Transfer Function
The transfer function is
 k 
VOUT(IDEAL) = 
V
 1024  REF
where k is the decimal equivalent of the binary DAC input
code and VREF is the voltage at REF (Pin 6).
Power-On Reset
The LTC1664 clears the outputs to zero-scale when power
is first applied, making system initialization consistent
and repeatable.
Power Supply Sequencing
The voltage at REF (Pin 6) should be kept within the range
–0.3V ≤ VREF ≤ VCC + 0.3V (see Absolute Maximum Ratings). Particular care should be taken to observe these
limits during power supply turn-on and turn-off sequences,
when the voltage at VCC (Pin 16) is in transition. If it is
not possible to sequence the supplies, connect a Schottky
diode from REF (anode) to VCC (cathode).
Serial Interface
Referring to Figure 2: With CS/LD held low, data on the DIN
input is shifted into the 16-bit shift register on the positive
edge of SCK. The 4-bit DAC address, A3-A0, is loaded first
(see Table 2), then the 10-bit input code, D9-D0, ordered
MSB-to-LSB in each case. Two don’t-care bits, X1-X0,
are loaded last. When the full 16-bit input word has been
shifted in, CS/LD is pulled high, loading the DAC register
with the word and causing the addressed DAC output(s)
to update. The clock is disabled internally when CS/LD is
high. Note: SCK must be low before CS/LD is pulled low.
The buffered serial output of the shift register is available on the DOUT pin, which swings from GND to VCC .
Data appears on DOUT 16 positive SCK edges after being
applied to DIN.
Multiple LTC1664’s can be controlled from a single 3-wire
serial port (i.e., SCK, DIN and CS/LD) by using the included
daisychain facility. A series of m chips is configured by
connecting each DOUT (except the last) to DIN of the next
chip, forming a single 16m -bit shift register. The SCK and
CS/LD signals are common to all chips in the chain. In
use, CS/LD is held low while m 16-bit words are clocked
to DIN of the first chip; CS/LD is then pulled high, updating
all of them simultaneously.
Sleep Mode
DAC address 1110 b is reserved for the special sleep instruction (see Table 2). In this mode, the digital interface stays
active while the analog circuits are disabled; static power
consumption is thus virtually eliminated. The reference
input and analog outputs are set in a high impedance state
and all DAC settings are retained in memory so that when
sleep mode is exited, the outputs of DACs not updated by
the Wake command are restored to their last active state.
Sleep mode is initiated by performing a load sequence to
address 1110 b (the DAC input word D9-D0 is ignored).
Once in sleep mode, a load sequence to any other address (including “No Change” address 0000 b) causes
the LTC1664 to Wake. It is possible to keep one or more
chips of a daisy chain in continuous sleep mode by giving
the sleep instruction to these chips each time the active
chips in the chain are updated.
Voltage Outputs
Each of the four rail-to-rail output amplifiers contained in
the LTC1664 can source or sink up to 5mA. The outputs
swing to within a few millivolts of either supply rail when
unloaded and have an equivalent output resistance of 85Ω
when driving a load to the rails. The output amplifiers are
stable driving capacitive loads of up to 1000pF.
A small resistor placed in series with the output can be
used to achieve stability for any load capacitance. A 1µF
Table 1. LTC1664 Input Word
A3 A2 A1 A0 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X1 X0
ADDRESS/CONTROL
INPUT CODE
DON’T CARE
1664fa
8
LTC1664
Operation
SCK
1
A3
DIN
2
A2
3
A1
4
A0
5
D9
6
7
D8
D7
8
D6
ADDRESS/CONTROL
9
10
D5
D4
11
12
D3
13
D2
D1
14
D0
INPUT CODE
15
X1
16
X0
DON’T CARE
INPUT WORD W0
CS/LD
DOUT
(ENABLE SCK)
(UPDATE OUTPUT)
A3
A2
A1
A0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
X1
INPUT WORD W–1
X0
A3
INPUT WORD W0
1664 F02
Figure 2. LTC1664 Register Loading Sequence
Table 2. DAC Address/Control Functions
ADDRESS/CONTROL
A3
A2
A1
A0
DAC STATUS
SLEEP STATUS
0
0
0
0
No Change
Wake
0
0
0
1
Load DAC A
Wake
0
0
1
0
Load DAC B
Wake
0
0
1
1
Load DAC C
Wake
0
1
0
0
Load DAC D
Wake
0
1
0
1
Reserved
0
1
1
0
Reserved
0
1
1
1
Reserved
1
0
0
0
Reserved
1
0
0
1
Reserved
1
0
1
0
Reserved
1
0
1
1
Reserved
1
1
0
0
Reserved
1
1
0
1
1
1
1
0
No Change
Sleep
1
1
1
1
Load ALL DACs
with Same
10-Bit Code
Wake
Reserved
1664fa
9
LTC1664
Operation
load can be successfully driven by inserting a 20Ω resistor; a 2.2µF load needs only a 10Ω resistor. In either case,
larger values of resistance, capacitance or both may be
safely substituted for the values given.
Rail-to-Rail Output Considerations
In any rail-to-rail voltage output DAC, the output is limited
to voltages within the supply range.
Similarly, limiting can occur near full-scale when the REF
pin is tied to VCC. If VREF = VCC and the DAC full-scale
error (FSE) is positive, the output for the highest codes
limits at VCC as shown in Figure 3c. No full-scale limiting
can occur if VREF is less than VCC – FSE.
Offset and linearity are defined and tested over the region
of the DAC transfer function where no output limiting can
occur.
If the DAC offset is negative, the output for the lowest
codes limits at 0V as shown in Figure 3b.
POSITIVE
FSE
VREF = VCC
OUTPUT
VOLTAGE
INPUT CODE
(3c)
VREF = VCC
OUTPUT
VOLTAGE
0
512
INPUT CODE
1023
(3a)
OUTPUT
VOLTAGE
NEGATIVE
OFFSET
0V
INPUT CODE
(3b)
1664 F03
Figure 3. Effects of Rail-to-Rail Operation On a DAC Transfer Curve. (a) Overall Transfer Function (b) Effect of Negative
Offset for Codes Near Zero-Scale (c) Effect of Positive Full-Scale Error for Input Codes Near Full-Scale When VREF = VCC
1664fa
10
VOUT1
4
3
2
0.1µF
3-WIRE
SERIAL
INTERFACE
1
0.1µF
LTC1258-2.5
2
3.3V
4
U2A
LT®1490
+
1
8
–
0.1µF
R2
11k
R2
11k
FINE
SCK
CS/LD
REF
VOUT B
R1
110Ω
COARSE VOUT A
GND
8
7
6
3
2
1
SHIFT REGISTER
ADDRESS
DECODER
DAC C
DAC D
1 CODE C 
 CODE D
+
= 2.5V 

 1024
100 1024 
 CODE D R1 CODE C 
+
VOUT2 = VREF 

 1024
R2 1024 
1 CODE B 
 CODE A
+
= 2.5V 

 1024
100 1024 
 CODE A R1 CODE B 
VOUT1 = VREF 
+

 1024
R2 1024 
CONTROL
LOGIC
DAC B
DAC A
U1
LTC1664
9
10
11
4
5
16
DIN
1664 TA01
DOUT
CLR
VOUT C
VOUT D
VCC
0.1µF
TO OTHER
LTC1664s
R2
11k
FINE
R1
110Ω
COARSE
3.3V
R2
11k
R1
110Ω
U2B
LT1490
0.1µF
5
6
+
R1 3.3V
110Ω
–
A Low Power Dual Trim Circuit with Coarse/Fine Adjustment
VOUT2
7
LTC1664
Typical Applications
1664fa
11
VOUT B ′
±5V
VOUT A ′
±5V
7
U2A
LT1491
U2B
LT1491
VS–
R
0.1µF 11
1
4
VS+
5
6
3
2
3-WIRE
SERIAL
INTERFACE
+
0.1µF
–
+
R
R
R
CLK
CS/LD
REF
VOUT B
VOUT A
GND
8
7
6
3
2
1
CONTROL
LOGIC
DAC B
DAC A
SHIFT REGISTER
U1
LTC1664
ADDRESS
DECODER
DAC C
DAC D
9
10
11
4
5
16
DIN
1664 TA02
DOUT
CLR
VOUT C
VOUT D
VCC
0.1µF
5V
R
R
10
9
12
13
U2D
LT1491
– 5V
0V
+4.99V
VOUT C′
±5V
VOUT D′
±5V
0
512
1023
8
14
VOUT X
R
R
CODE
U2C
LT1491
+
–
–
12
+
–
A 4-Channel Bipolar Output Voltage Circuit Configuration
LTC1664
Typical Applications
1664fa
LTC1664
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
GN Package
16-Lead Plastic SSOP (Narrow 0.150)
(LTC DWG # 05-08-1641)
.189 – .196*
(4.801 – 4.978)
.045 ±.005
16 15 14 13 12 11 10 9
.254 MIN
.009
(0.229)
REF
.150 – .165
.229 – .244
(5.817 – 6.198)
.0165 ±.0015
.150 – .157**
(3.810 – 3.988)
.0250 BSC
RECOMMENDED SOLDER PAD LAYOUT
1
.015 ±.004
× 45°
(0.38 ±0.10)
.007 – .0098
(0.178 – 0.249)
.0532 – .0688
(1.35 – 1.75)
2 3
4
5 6
7
8
.004 – .0098
(0.102 – 0.249)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. CONTROLLING DIMENSION: INCHES
INCHES
2. DIMENSIONS ARE IN
(MILLIMETERS)
.008 – .012
(0.203 – 0.305)
TYP
.0250
(0.635)
BSC
GN16 (SSOP) 0204
3. DRAWING NOT TO SCALE
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
1664fa
13
LTC1664
Package Description
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
N Package
16-LeadNPDIP
(Narrow 0.300)
Package
(LTC
DWG
# 05-08-1510)
16-Lead
PDIP
(Narrow
.300 Inch)
(Reference LTC DWG # 05-08-1510 Rev I)
.770*
(19.558)
MAX
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
.255 ± .015*
(6.477 ± 0.381)
.300 – .325
(7.620 – 8.255)
.008 – .015
(0.203 – 0.381)
(
+.035
.325 –.015
+0.889
8.255
–0.381
NOTE:
1. DIMENSIONS ARE
)
.130 ± .005
(3.302 ± 0.127)
.045 – .065
(1.143 – 1.651)
.020
(0.508)
MIN
.065
(1.651)
TYP
.120
(3.048)
MIN
.100
(2.54)
BSC
.018 ± .003
(0.457 ± 0.076)
N16 REV I 0711
INCHES
MILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
1664fa
14
LTC1664
Revision History
REV
DATE
DESCRIPTION
PAGE NUMBER
A
01/12
Removed Typical values in the Timing Characteristics section.
4
Corrected Related Parts listing for LTC1659.
16
1664fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LTC1664
Typical Application
An 11-Bit Pin Driver VH and VL Adjustment Circuit for ATE Applications
5V
11
16
6
CLR
VCC
REF
0.1µF
VH
(FROM MAIN DAC)
U1 LTC1664
DAC A
2
RG
VA 50k
RF
5k
10V
3
2
DAC B
3
DAC C
4
RG
VB 50k
CS/LD
7
DIN
9
SCK
8
5
GND
1
1
U2A
LT1368
–
4
– 5V
RG
VC 50k
RF
5k
5
RG
VD 50k
1664 TA03
VL′
0.1µF
RF
5k
VH
VL
+
7
U2B
LT1368
RF
5k
CODE B
1023
512
0
1023
512
0
1023
512
0
VOUT
PIN
DRIVER
VL′ = VL + ∆VL
0.1µF
–
CODE A
1023
1023
1023
512
512
512
0
0
0
VH′
VH′ = VH + ∆VH
0.1µF
VL
(FROM MAIN DAC)
6
DAC D
+
0.1µF
8
LOGIC
DRIVE
∆VH, ∆VL
0
+ 250mV
+500mV
– 250mV
0
+ 250mV
–500mV
–250mV
0
VA = VC = 2.5V
R
VH′ = VH + F (VA – VB)
RG
R
VL′ = VL + F (VC – VD)
RG
For Resistor Values Shown:
Adjustment Range = ±500mV
Adjustment Step Size = 500µV
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LTC1665/LTC1660
Octal 8-/10-Bit VOUT DAC in 16-Pin Narrow SSOP
VCC = 2.7V to 5.5V, 60μA per DAC, Rail-to-Rail Output
LTC1661
Dual 10-Bit VOUT DAC in 8-Pin MSOP Package
VCC = 2.7V to 5.5V, 60μA per DAC, Rail-to-Rail Output
LTC1662
Ultra Low Power Dual 10-Bit VOUT DAC in 8-Pin MSOP Package
VCC = 2.7V to 5.5V, 1.5μA per DAC, Rail-to-Rail Output
LTC1663
Single 10-Bit VOUT DAC with 2-Wire Interface in SOT-23 Package
VCC = 2.7V to 5.5V, Internal Reference, 60µA
LTC1446/LTC1446L
Dual 12-Bit VOUT DACs in SO-8 Package with Internal Reference
LTC1446: VCC = 4.5V to 5.5V, VOUT = 0V to 4.095V
LTC1446L: VCC = 2.7V to 5.5V, VOUT = 0V to 2.5V
LTC1448
Dual 12-Bit VOUT DAC in SO-8 Package
VCC = 2.7V to 5.5V, External Reference Can Be Tied to VCC
LTC1454/LTC1454L
Dual 12-Bit VOUT DACs in SO-16 Package with Added Functionality
LTC1454: VCC = 4.5V to 5.5V, VOUT = 0V to 4.095V
LTC1454L: VCC = 2.7V to 5.5V, VOUT = 0V to 2.5V
LTC1458/LTC1458L
Quad 12-Bit Rail-to-Rail Output DACs with Added Functionality
LTC1458: VCC = 4.5V to 5.5V, VOUT = 0V to 4.095V
LTC1458L: VCC = 2.7V to 5.5V, VOUT = 0V to 2.5V
LT1460
Micropower Precision Series Reference, 2.5V, 5V, 10V Versions
0.075% Max, 10ppm/°C Max, Only 130µA Supply Current
LTC1590
Dual 12-Bit IOUT DAC in SO-16 Package
VCC = 4.5V to 5.5V, 4-Quadrant Multiplication
LTC1654
Dual 14-Bit DAC in SO-8 Footprint
1LBS DNL, Selectable Speed/Power
LTC1659
Single Rail-to-Rail 12-Bit VOUT DAC in 8-Lead MSOP Package
VCC = 2.7V to 5.5V, Low Power Multiplying VOUT DAC. Output
Swings from GND to REF. REF Input Can Be Tied to VCC
1664fa
16 Linear Technology Corporation
LT 0112 REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2000