SpectraLinear CY28349B Ftg for intelâ® pentiumâ® 4 cpu and chipset Datasheet

CY28349B
FTG for Intel® Pentium® 4 CPU and Chipsets
Features
• Compatible to Intel® CK-Titan and CK-408 Clock
Synthesizer/driver specifications
• Support SMBus byte read/write and block read/ write
operations to simplify system BIOS development
• System frequency synthesizer for Intel Brookdale 845
and Brookdale – G Pentium® 4 chipsets
• Vendor ID and Revision ID support
• Programmable clock output frequency with less than
1-MHz increment
• Programmable output skew support
• Integrated fail-safe Watchdog timer for system
recovery
• Available in 48-pin SSOP
• Automatically switch to hardware-selected or softwareprogrammed clock frequency when w timer time-out
• Fixed 3V66 and PCI output frequency mode.
• Programmable drive strength support
• Power management control inputs
CPU
3V66
PCI
REF
48M
24_48M
x3
x4
x 10
x2
x1
x1
• Capable of generating system RESET after a Watchdog
timer time-out occurs or a change in output frequency
via SMBus interface
Pin Configuration [1]
Block Diagram
X1
X2
PLL Ref Freq
Divider
Network
*MULTSEL0:1
PLL2
2
SMBus
Logic
RST#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
CY28349B
PWR_DWN#
SDATA
SCLK
*MULTSEL1/REF1
VDD_REF
X1
X2
GND_PCI
*FS2/PCI_F0
*FS3/PCI_F1
PCI_F2
VDD_PCI
VDD_3V66
*FS4/PCI0
3V66_0:2
PCI1
PCI2
GND_PCI
VDD_PCI
PCI3
PCI_F0:2
PCI4
PCI0:6
PCI5
VDD_48MHz
PCI6
3V66_3/48MHz_1
VDD_PCI
VTT_PWRGD#
VDD_48MHz
48MHz_0
RST#
GND_48MHz
*FS0/48MHz_0
24_48MHz
*FS1/24_48MHz
VDD_48MHz
VDD_CPU
CPU0:1, CPU0:1#,
CPU_ITP, CPU_ITP#
~
PLL 1
*FS0:4
VTT_PWRGD#
VDD_REF
REF0:1
XTAL
OSC
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
REF0/MULTSEL0*
GND_REF
VDD_CPU
CPU_ITP
CPU_ITP#
GND_CPU
PWR_DWN#
CPU0
CPU0#
VDD_CPU
CPU1
CPU1#
GND_CPU
IREF
VDD_CORE
GND_CORE
VDD_3V66
3V66_0
3V66_1
GND_3V66
3V66_2
3V66_3/48MHz_1
SCLK
SDATA
SSOP-48
Note:
1. Signals marked with ‘*’ and “^” have internal pull-up and pull-down resistors, respectively.
Rev 1.0, November 20, 2006
2200 Laurelwood Road, Santa Clara, CA 95054
Page 1 of 20
Tel:(408) 855-0555
Fax:(408) 855-0550
www.SpectraLinear.com
CY28349B
Pin Definitions
Pin No.
Pin
Type
X1
3
I
Crystal Connection or External Reference Frequency Input: This pin has dual
functions. It can be used as an external 14.318-MHz crystal connection or as an
external reference frequency input.
X2
4
O
Crystal Connection: Connection for an external 14.318-MHz crystal. If using an
external reference, this pin must be left unconnected.
REF0/MULTSEL0
48
I/O
Reference Clock 0/Current Multiplier Selection 0: 3.3V 14.318-MHz clock
output. This pin also serves as a power-on strap option to determine the current
multiplier for the CPU clock outputs. The MULTSEL1:0 definitions are as follows:
MULTSEL1:0
00 = Ioh is 4 x IREF
01 = Ioh is 5 x IREF
10 = Ioh is 6 x IREF
11 = Ioh is 7 x IREF
REF1/MULTSEL1
1
I/O
Reference Clock 1/Current Multiplier Selection 1: 3.3V 14.318-MHz clock
output. This pin also serves as a power-on strap option to determine the current
multiplier for the CPU clock outputs. The MULTSEL1:0 definitions are as follows:
MULTSEL1:0
00 = Ioh is 4 x IREF
01 = Ioh is 5 x IREF
10 = Ioh is 6 x IREF
11 = Ioh is 7 x IREF
CPU0:1, CPU0:1#
41, 38, 40, 37
O
CPU Clock Outputs: Frequency is set by the FS0:4 inputs or through serial input
interface.
44, 45
I/O
CPU Clock Output for ITP: Frequency is set by the FS0:4 inputs or through serial
input interface.
31, 30, 28
O
66-MHz Clock Outputs: 3.3V fixed 66-MHz clock.
PCI_F0/FS2
6
I/O
Free-running PCI Output 0/Frequency Select 2: 3.3V free-running PCI output.
This pin also serves as a power-on strap option to determine device operating
frequency as described in the Frequency Selection Table.
PCI_F1/FS3
7
I/O
Free-running PCI Output 1/Frequency Select 3: 3.3V free-running PCI output.
This pin also serves as a power-on strap option to determine device operating
frequency as described in Table 4.
Pin Name
CPU_ITP, CPU_ITP#
3V66_0:2
Pin Description
PCI_F2
8
I/O
Free-running PCI Output 2: 3.3V free-running PCI output.
PCI0/FS4
10
I/O
PCI Output 0/Frequency Select 4: 3.3V PCI output. This pin also serves as a
power-on strap option to determine device operating frequency as described in
Table 4.
11, 12, 14, 15,
16, 17
O
PCI Clock Output 1 to 6: 3.3V PCI clock outputs.
48MHz_0/FS0
22
I/O
48-MHz Output/Frequency Select 0: 3.3V fixed 48-MHz, non-spread spectrum
output. This pin also serves as a power-on strap option to determine device
operating frequency as described in Table 4.
This output will be used as the reference clock for USB host controller in Intel 845
(Brookdale) platforms. For Intel Brookdale – G platforms, this output will be used
as the VCH reference clock.
24_48MHz/FS1
23
I/O
24- or 48-MHz Output/Frequency Select 1: 3.3V fixed 24-MHz or 48-MHz
non-spread spectrum output. This pin also serves as a power-on strap option to
determine device operating frequency as described in Table 4.
This output will be used as the reference clock for SIO devices in Intel 845
(Brookdale) platforms. For Intel Brookdale – G platforms, this output will be used
as the reference clock for both USB host controller and SIO devices. We
recommend system designer to configure this output as 48 MHz and “HIGH Drive”
by setting Byte [5], Bit [0] and Byte [9], Bit [7], respectively.
3V66_3/48MHz_1
27
O
48-MHz or 66-MHz Output: 3.3V output.
PCI1:6
Rev 1.0, November 20, 2006
Page 2 of 20
CY28349B
Pin Definitions (continued)
Pin No.
Pin
Type
PWR_DWN#
42
I
Power-down Control: 3.3V LVTTL compatible input that places the device in
power down mode when held low.
SCLK
26
I
SMBus Clock Input: Clock pin for serial interface.
SDATA
25
I/O
RST#
20
IREF
35
I
Current Reference for CPU Output: A precision resistor is attached to this pin
which is connected to the internal current reference.
VTT_PWRGD#
19
I
Powergood from Voltage Regulator Module (VRM): 3.3V LVTTL input.
VTT_PWRGD# is a level-sensitive strobe used to determine when FS0:4 and
MULTSEL0:1 inputs are valid and OK to be sampled (Active LOW). Once
VTT_PWRGD# is sampled LOW, the status of this input will be ignored.
VDD_REF,
VDD _PCI,
VDD_48MHz,
VDD_3V66,
VDD_CPU
2, 9, 18, 24,
32, 39, 46
P
3.3V Power Connection: Power supply for CPU outputs buffers, 3V66 output
buffers, PCI output buffers, reference output buffers and 48-MHz output buffers.
Connect to 3.3V.
GND_PCI,
GND_48MHz,
GND_3V66,
GND_CPU,
GND_REF,
5, 13, 21, 29,
36, 43, 47
G
Ground Connection: Connect all ground pins to the common system ground
plane.
VDD_CORE
34
P
3.3V Analog Power Connection: Power supply for core logic, PLL circuitry.
Connect to 3.3V.
GND_CORE
33
G
Analog Ground Connection: Ground for core logic, PLL circuitry.
Pin Name
Rev 1.0, November 20, 2006
Pin Description
SMBus Data Input: Data pin for serial interface.
O
System Reset Output: Open-drain system reset output.
(open-d
rain)
Page 3 of 20
CY28349B
Swing Select Functions
MULTSEL1
MULTSEL0
Board Target
Trace/Term Z
Reference R, IREF =
VDD/(3*Rr)
Output
Current
VOH @ Z
0
0
50:
Rr = 221 1%,
IREF = 5.00 mA
IOH = 4*Iref
1.0V @ 50
0
0
60:
Rr = 221 1%,
IREF = 5.00 mA
IOH = 4*Iref
1.2V @ 60
0
1
50:
Rr = 221 1%,
IREF = 5.00 mA
IOH = 5*Iref
1.25V @ 50
0
1
60:
Rr = 221 1%,
IREF = 5.00 mA
IOH = 5*Iref
1.5V @ 60
1
0
50:
Rr = 221 1%,
IREF = 5.00 mA
IOH = 6*Iref
1.5V @ 50
1
0
60:
Rr = 221 1%,
IREF = 5.00 mA
IOH = 6*Iref
1.8V @ 60
1
1
50:
Rr = 221 1%,
IREF = 5.00 mA
IOH = 7*Iref
1.75V @ 50
1
1
60:
Rr = 221 1%,
IREF = 5.00 mA
IOH = 7*Iref
2.1V @ 60
0
0
50:
Rr = 475 1%,
IREF = 2.32 mA
IOH = 4*Iref
0.47V @ 50
0
0
60:
Rr = 475 1%,
IREF = 2.32 mA
IOH = 4*Iref
0.56V @ 60
0
1
50:
Rr = 475 1%,
IREF = 2.32 mA
IOH = 5*Iref
0.58V @ 50
0
1
60:
Rr = 475 1%,
IREF = 2.32 mA
IOH = 5*Iref
0.7V @ 60
1
0
50:
Rr = 475 1%,
IREF = 2.32 mA
IOH = 6*Iref
0.7V @ 50
1
0
60:
Rr = 475 1%,
IREF = 2.32 mA
IOH = 6*Iref
0.84V @ 60
1
1
50:
Rr = 475 1%,
IREF = 2.32 mA
IOH = 7*Iref
0.81V @ 50
1
1
60:
Rr = 475 1%,
IREF = 2.32 mA
IOH = 7*Iref
0.97V @ 60
Rev 1.0, November 20, 2006
Page 4 of 20
CY28349B
Serial Data Interface
Data Protocol
To enhance the flexibility and function of the clock synthesizer,
a two-signal serial interface is provided. Through the Serial
Data Interface, various device functions such as individual
clock output buffers, etc. can be individually enabled or
disabled.
The register associated with the Serial Data Interface
initializes to its default setting upon power-up, and therefore
use of this interface is optional. Clock device register changes
are normally made upon system initialization, if any are
required. The interface can also be used during system
operation for power management functions.
The clock driver serial protocol accepts Byte Write, byte read,
Block Write and Block Read operation from the controller. For
Block Write/Read operation, the bytes must be accessed in
sequential order from lowest to highest byte (most significant
bit first) with the ability to stop after any complete byte has
been transferred. For Byte Write and Byte Read operations,
the system controller can access individual indexed bytes. The
offset of the indexed byte is encoded in the command code,
as described in Table 1.
The Block Write and Block Read protocol is outlined in Table 2
while Table 3 outlines the corresponding byte write and byte
read protocol.
The slave receiver address is 11010010 (D2h).
Table 1. Command Code Definition
Bit
Descriptions
0 = Block Read or Block Write operation
1 = Byte Read or Byte Write operation
7
Byte offset for Byte Read or Byte Write operation. For Block Read or Block Write operations,
these bits should be ‘0000000’.
6:0
Table 2. Block Read and Block Write Protocol
Block Write Protocol
Bit
1
2:8
Description
Start
Block Read Protocol
Bit
1
Slave address – 7 bits
2:8
Description
Start
Slave address – 7 bits
9
Write
9
Write
10
Acknowledge from slave
10
Acknowledge from slave
11:18
19
20:27
28
29:36
37
38:45
Command Code – 8 bits
‘00000000’ stands for block operation
11:18
Command Code – 8 bits
‘00000000’ stands for block operation
Acknowledge from slave
19
Acknowledge from slave
Byte Count – 8 bits
20
Repeat start
Acknowledge from slave
Data byte 0 – 8 bits
Acknowledge from slave
Data byte 1 – 8 bits
46
Acknowledge from slave
...
Data Byte N/Slave Acknowledge...
...
Data Byte N – 8 bits
...
Acknowledge from slave
...
Stop
21:27
Slave address – 7 bits
28
Read
29
Acknowledge from slave
30:37
38
39:46
47
48:55
Byte count from slave – 8 bits
Acknowledge
Data byte from slave – 8 bits
Acknowledge
Data byte from slave – 8 bits
56
Acknowledge
...
Data bytes from slave/Acknowledge
...
Data byte N from slave – 8 bits
...
Not Acknowledge
...
Stop
Table 3. Byte Read and Byte Write Protocol
Byte Write Protocol
Bit
1
2:8
Description
Start
Slave address – 7 bits
Rev 1.0, November 20, 2006
Byte Read Protocol
Bit
1
2:8
Description
Start
Slave address – 7 bits
Page 5 of 20
CY28349B
Table 3. Byte Read and Byte Write Protocol (continued)
Byte Write Protocol
Bit
Byte Read Protocol
Description
Bit
Description
9
Write
9
Write
10
Acknowledge from slave
10
Acknowledge from slave
11:18
19
20:27
Command Code – 8 bits
‘1xxxxxxx’ stands for byte operation
bit[6:0] of the command code represents the offset
of the byte to be accessed
11:18
Command Code – 8 bits
‘1xxxxxxx’ stands for byte operation
bit[6:0] of the command code represents the offset
of the byte to be accessed
Acknowledge from slave
19
Acknowledge from slave
Data byte – 8 bits
20
Repeat start
28
Acknowledge from slave
29
Stop
21:27
28
29
30:37
Slave address – 7 bits
Read
Acknowledge from slave
Data byte from slave – 8 bits
38
Not Acknowledge
39
Stop
Data Byte Configuration Map
Data Byte 0
Bit
Pin#
Name
Description
Power On
Default
Bit 7
–
Spread Select2
‘000’ = OFF
0
Bit 6
–
Spread Select1
‘001’ = Reserved
0
Bit 5
–
Spread Select0
‘010’ = Reserved
0
‘011’ = Reserved
‘100’ = ± 0.25%
‘101’ = – 0.5%
‘110’ = ±0.5%
‘111’ = ±0.38%
SW Frequency selection bits. See Table 4.
Bit 4
–
SEL4
0
Bit 3
–
SEL3
0
Bit 2
–
SEL2
0
Bit 1
–
SEL1
0
Bit 0
–
SEL0
0
Data Byte 1
Bit
Pin#
Name
Description
Power On
Default
Bit 7
38, 37
CPU1, CPU1#
(Active/Inactive)
1
Bit 6
41, 40
CPU0, CPU0#
(Active/Inactive)
1
Bit 5
22
48MHz
(Active/Inactive)
1
Bit 4
23
24_48MHz
(Active/Inactive)
1
Bit 3
27
3V66_3
(Active/Inactive)
1
Bit 2
28
3V66_2
(Active/Inactive)
1
Bit 1
30
3V66_1
(Active/Inactive)
1
Bit 0
31
3V66_0
(Active/Inactive)
1
Rev 1.0, November 20, 2006
Page 6 of 20
CY28349B
Data Byte 2
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 7
–
Reserved
Reserved
0
Bit 6
17
PCI6
(Active/Inactive)
1
Bit 5
16
PCI5
(Active/Inactive)
1
Bit 4
15
PCI4
(Active/Inactive)
1
Bit 3
14
PCI3
(Active/Inactive)
1
Bit 2
12
PCI2
(Active/Inactive)
1
Bit 1
11
PCI1
(Active/Inactive)
1
Bit 0
10
PCI0
(Active/Inactive)
1
Data Byte 3
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 7
8
PCI_F2
(Active/Inactive)
1
Bit 6
7
PCI_F1
(Active/Inactive)
1
Bit 5
6
PCI_F0
(Active/Inactive)
1
Bit 4
–
Bit 3
44, 45
Reserved
Reserved
0
CPU_ITP, CPU_ITP#
(Active/Inactive)
1
Bit 2
Bit 1
–
Reserved
Reserved
0
1
REF1
(Active/Inactive)
1
Bit 0
48
REF0
(Active/Inactive)
1
Data Byte 4
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 7
–
MULTSEL_Override
This bit control the selection of IREF multiple.
0 = HW control; IREF multiplier is determined by
MULTSEL[0:1] input pins
1 = SW control; IREF multiplier is determined by Byte[4],
Bit[5:6].
0
IREF multiplier
00 = Ioh is 4 x IREF
01 = Ioh is 5 x IREF
10 = Ioh is 6 x IREF
11 = Ioh is 7 x IREF
0
Bit 6
–
SW_MULTSEL1
Bit 5
–
SW_MULTSEL0
Bit 4
–
Reserved
Reserved
Reserved
Bit 3
–
Reserved
Reserved
Reserved
Bit 2
–
Reserved
Reserved
Reserved
Bit 1
–
Reserved
Reserved
Reserved
Bit 0
–
Reserved
Reserved
Reserved
0
Data Byte 5
Bit
Pin#
Name
Pin Description
Latched FS[4:0] inputs. These bits are read-only.
Power On
Default
Bit 7
10
Latched FS4 input
Bit 6
7
Latched FS3 input
X
X
Bit 5
6
Latched FS2 input
X
Bit 4
23
Latched FS1 input
X
Bit 3
22
Latched FS0 input
X
Rev 1.0, November 20, 2006
Page 7 of 20
CY28349B
Data Byte 5 (continued)
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 2
–
FS_Override
0 = Select operating frequency by FS[4:0] input pins
1 = Select operating frequency by SEL[4:0] settings
0
Bit 1
27
SEL 3V66
0 = 48-MHz output on pin 27
1 = 66-MHz output on pin 27
0
Bit 0
23
SEL 48MHZ
0 = 24-MHz
1 = 48-MHz
0
Data Byte 6
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 7
–
Revision_ID3
Revision ID bit[3]
0
Bit 6
–
Revision_ID2
Revision ID bit[2]
0
Bit 5
–
Revision_ID1
Revision ID bit[1]
0
Bit 4
–
Revision_ID0
Revision ID bit[0]
0
Bit 3
–
Vendor_ID3
Bit[3] of Cypress’s Vendor ID. This bit is read-only.
1
Bit 2
–
Vendor_ID2
Bit[2] of Cypress’s Vendor ID. This bit is read-only.
0
Bit 1
–
Vendor _ID1
Bit[1] of Cypress’s Vendor ID. This bit is read-only.
0
Bit 0
–
Vendor _ID0
Bit[0] of Cypress’s Vendor ID. This bit is read-only.
0
Data Byte 7
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 7
–
Reserved
Reserved
0
Bit 6
–
Reserved
Reserved
0
Bit 5
–
Reserved
Reserved
0
Bit 4
–
Reserved
Reserved
0
Bit 3
–
Reserved
Reserved
0
Bit 2
–
Reserved
Reserved
0
Bit 1
–
Reserved
Reserved
0
Bit 0
–
Reserved
Reserved
0
Data Byte 8
Bit
Bit 7
Pin#
–
Name
Reserved
Power On
Default
Pin Description
Reserved
0
Bit 6
–
Reserved
Reserved
0
Bit 5
–
WD_TIMER4
1
Bit 4
–
WD_TIMER3
Bit 3
–
WD_TIMER2
Bit 2
–
WD_TIMER1
Bit 1
–
WD_TIMER0
These bits store the time-out value of the Watchdog Timer.
The scale of the timer is determine by the pre-scaler. The
timer can support a value of 150 ms to 4.8 sec when the
pre-scaler is set to 150 ms. If the prescaler is set to 2.5 sec,
it can support a value from 2.5 sec to 80 sec. When the
Watchdog Timer reaches “0,” it will set the WD_TO_STATUS
bit and generate Reset if RST_EN_WD is enabled.
Bit 0
–
WD_PRE_SCALER
0 = 150 ms
1 = 2.5 sec
0
Rev 1.0, November 20, 2006
1
1
1
1
Page 8 of 20
CY28349B
Data Byte 9
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 7
–
48MHz_DRV
48MHz and 24_48MHz clock output drive strength
0 = Normal
1 = High Drive
(Recommend to set to high drive if this output is being used
to drive both USB and SIO devices in Intel Brookdale - G
platforms)
0
Bit 6
–
PCI_DRV
PCI clock output drive strength
0 = Normal
1 = High Drive
0
Bit 5
–
3V66_DRV
3V66 clock output drive strength
0 = Normal
1 = High Drive
0
Bit 4
–
RST_EN_WD
This bit will enable the generation of a Reset pulse when a
Watchdog timer time-out occurs.
0 = Disabled
1 = Enabled
0
Bit 3
–
RST_EN_FC
This bit will enable the generation of a Reset pulse after a
frequency change occurs.
0 = Disabled
1 = Enabled
0
Bit 2
–
WD_TO_STATUS
Watchdog Timer Time-out Status bit
0 = No time-out occurs (Read); Ignore (Write)
1 = time-out occurred (Read); Clear WD_TO_STATUS
(Write)
0
Bit 1
–
WD_EN
0 = Stop and reload Watchdog Timer
1 = Enable Watchdog Timer. It will start counting down after
a frequency change occurs.
Note: CY28349B will generate system reset, reload a
recovery frequency, and lock itself into a recovery
frequency mode after a Watchdog Timer time-out occurs.
Under recovery frequency mode, CY28349B will not
respond to any attempt to change output frequency via the
SMBus control bytes. System software can unlock
CY28349B from its recovery frequency mode by clearing
the WD_EN bit.
0
Bit 0
–
Reserved
Reserved
0
Data Byte 10
Bit
Pin#
Name
Bit 7
–
CPU_Skew2
Bit 6
–
CPU_Skew1
Bit 5
–
CPU_Skew0
Bit 4
–
Fixed 3V66/PCI
Rev 1.0, November 20, 2006
Power On
Default
Pin Description
CPU skew control
000 = Normal
001 = –150 ps
010 = –300 ps
011 = –450 ps
100 = +150 ps
101 = +300 ps
110 = +450 ps
111 = +600 ps
0
Fixed 3V66 and PCI output mode
0 = Disabled
1 = Enabled
When enabled, 3V66 and PCI output frequency will be fixed
at 64 MHz and 32 MHz respectively.
0
0
0
Page 9 of 20
CY28349B
Data Byte 10 (continued)
Bit
Pin#
Name
Bit 3
–
PCI_Skew1
Bit 2
–
PCI_Skew0
Bit 1
–
3V66_Skew1
Bit 0
–
3V66_Skew0
Power On
Default
Pin Description
PCI skew control
00 = Normal
01 = –500 ps
10 = Reserved
11 = +500 ps
0
3V66 skew control
00 = Normal
01 = –150 ps
10 = +150 ps
11 = +300 ps
0
0
0
Data Byte 11
Bit
Pin#
Name
Bit 7
–
ROCV_FREQ_N7
Bit 6
–
ROCV_FREQ_N6
Bit 5
–
ROCV_FREQ_N5
Bit 4
–
ROCV_FREQ_N4
Bit 3
–
ROCV_FREQ_N3
Bit 2
–
ROCV_FREQ_N2
Bit 1
–
ROCV_FREQ_N1
Bit 0
–
ROCV_FREQ_N0
Power On
Default
Pin Description
If ROCV_FREQ_SEL is set, the values programmed in
ROCV_FREQ_N[7:0] and ROCV_FREQ_M[6:0] will be
used to determine the recovery CPU output frequency
when a Watchdog Timer time-out occurs.
The setting of FS_Override bit determines the frequency
ratio for CPU and other output clocks. When FS_Override
bit is cleared, the same frequency ratio stated in the
Latched FS[4:0] register will be used. When it is set, the
frequency ratio stated in the SEL[4:0] register will be used.
0
0
0
0
0
0
0
0
Data Byte 12
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 7
–
ROCV_FREQ_SEL
ROCV_FREQ_SEL determines the source of the recover
frequency when a Watchdog Timer time-out occurs. The
clock generator will automatically switch to the recovery
CPU frequency based on the selection on
ROCV_FREQ_SEL.
0 = From latched FS[4:0]
1 = From the settings of ROCV_FREQ_N[7:0] &
ROCV_FREQ_M[6:0]
0
Bit 6
–
ROCV_FREQ_M6
0
Bit 5
–
ROCV_FREQ_M5
Bit 4
–
ROCV_FREQ_M4
Bit 3
–
ROCV_FREQ_M3
Bit 2
–
ROCV_FREQ_M2
Bit 1
–
ROCV_FREQ_M1
Bit 0
–
ROCV_FREQ_M0
If ROCV_FREQ_SEL is set, the values programmed in
ROCV_FREQ_N[7:0] and ROCV_FREQ_M[6:0] will be
used to determine the recovery CPU output
frequency.when a Watchdog Timer time-out occurs.
The setting of FS_Override bit determines the frequency
ratio for CPU and other output clocks. When FS_Override
bit is cleared, the same frequency ratio stated in the
Latched FS[4:0] register will be used. When it is set, the
frequency ratio stated in the SEL[4:0] register will be used.
Rev 1.0, November 20, 2006
0
0
0
0
0
0
Page 10 of 20
CY28349B
Data Byte 13
Bit
Pin#
Name
Bit 7
–
CPU_FSEL_N7
Bit 6
–
CPU_FSEL_N6
Bit 5
–
CPU_FSEL_N5
Bit 4
–
CPU_FSEL_N4
Bit 3
–
CPU_FSEL_N3
Bit 2
–
CPU_FSEL_N2
Bit 1
–
CPU_FSEL_N1
Bit 0
–
CPU_FSEL_N0
Power On
Default
Pin Description
If Prog_Freq_EN is set, the values programmed in
CPU_FSEL_N[7:0] and CPU_FSEL_M[6:0] will be used to
determine the CPU output frequency. The new frequency
will start to load whenever CPU_FSELM[6:0] is updated.
The setting of FS_Override bit determines the frequency
ratio for CPU and other output clocks. When it is cleared,
the same frequency ratio stated in the Latched FS[4:0]
register will be used. When it is set, the frequency ratio
stated in the SEL[4:0] register will be used.
0
0
0
0
0
0
0
0
Data Byte 14
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 7
–
Pro_Freq_EN
Programmable output frequencies enabled
0 = Disabled
1 = Enabled
0
If Prog_Freq_EN is set, the values programmed in
CPU_FSEL_N[7:0] and CPU_FSEL_M[6:0] will be used to
determine the CPU output frequency. The new frequency
will start to load whenever CPU_FSELM[6:0] is updated.
The setting of FS_Override bit determines the frequency
ratio for CPU and other output clocks. When it is cleared,
the same frequency ratio stated in the Latched FS[4:0]
register will be used. When it is set, the frequency ratio
stated in the SEL[4:0] register will be used.
0
Bit 6
–
CPU_FSEL_M6
Bit 5
–
CPU_FSEL_M5
Bit 4
–
CPU_FSEL_M4
Bit 3
–
CPU_FSEL_M3
Bit 2
–
CPU_FSEL_M2
Bit 1
–
CPU_FSEL_M1
Bit 0
–
CPU_FSEL_M0
0
0
0
0
0
0
Data Byte 15
Bit
Pin#
Name
Pin Description
Power On
Default
Bit 7
–
Reserved
Reserved
0
Bit 6
–
Reserved
Reserved
0
Bit 5
–
Reserved
Reserved
0
Bit 4
–
Reserved
Reserved
0
Bit 3
–
Reserved
Reserved
0
Bit 2
–
Reserved
Reserved
0
Bit 1
–
Vendor Test Mode
Reserved. Write with “1”
1
Bit 0
–
Vendor Test Mode
Reserved. Write with “1”
1
Data Byte 16
Bit
Pin#
Name
Pin Description
Power On
Default
Bit 7
–
Reserved
Reserved
0
Bit 6
–
Reserved
Reserved
0
Bit 5
–
Reserved
Reserved
0
Bit 4
–
Reserved
Reserved
0
Bit 3
–
Reserved
Reserved
0
Bit 2
–
Reserved
Reserved
0
Bit 1
–
Reserved
Reserved
0
Bit 0
–
Reserved
Reserved
0
Rev 1.0, November 20, 2006
Page 11 of 20
CY28349B
Data Byte 17
Bit
Pin#
Name
Power On
Default
Pin Description
Bit 7
–
Reserved
Reserved
0
Bit 6
–
Reserved
Reserved
0
Bit 5
–
Reserved
Reserved
0
Bit 4
–
Reserved
Reserved
0
Bit 3
–
Reserved
Reserved
0
Bit 2
–
Reserved
Reserved
0
Bit 1
–
Reserved
Reserved
0
Bit 0
–
Reserved
Reserved
0
Table 4. Frequency Selection Table
Input Conditions
Output Frequency
FS4
FS3
FS2
FS1
FS0
SEL4
SEL3
SEL2
SEL1
SEL0
CPU
3V66
PCI
PLL Gear
Constants
(G)
0
0
0
0
0
100.7
67.1
33.6
48.00741
0
0
0
0
1
100.9
67.3
33.6
48.00741
0
0
0
1
0
108.0
72.0
36.0
48.00741
0
0
0
1
1
101.2
67.5
33.7
48.00741
0
0
1
0
0
114.0
76.0
38.0
48.00741
0
0
1
0
1
117.0
78.0
39.0
48.00741
0
0
1
1
0
120.0
80.0
40.0
48.00741
0
0
1
1
1
123.0
82.0
41.0
48.00741
0
1
0
0
0
126.0
63.0
31.5
48.00741
0
1
0
0
1
130.0
65.0
32.5
48.00741
0
1
0
1
0
133.9
67.0
33.5
48.00741
0
1
0
1
1
134.2
67.1
33.6
48.00741
0
1
1
0
0
134.5
67.3
33.6
48.00741
0
1
1
0
1
148.0
74.0
37.0
48.00741
0
1
1
1
0
152.0
76.0
38.0
48.00741
0
1
1
1
1
156.0
78.0
39.0
48.00741
1
0
0
0
0
160.0
80.0
40.0
48.00741
1
0
0
0
1
164.0
82.0
41.0
48.00741
1
0
0
1
0
167.4
66.9
33.5
48.00741
1
0
0
1
1
170.0
68.0
34.0
48.00741
1
0
1
0
0
175.0
70.0
35.0
48.00741
1
0
1
0
1
180.0
72.0
36.0
48.00741
1
0
1
1
0
185.0
74.0
37.0
48.00741
1
0
1
1
1
190.0
76.0
38.0
48.00741
1
1
0
0
0
166.8
66.7
33.4
48.00741
1
1
0
0
1
100.2
66.8
33.4
48.00741
1
1
0
1
0
133.6
66.8
33.4
48.00741
1
1
0
1
1
200.4
66.8
33.4
48.00741
1
1
1
0
0
166.6
66.6
33.3
48.00741
1
1
1
0
1
100.0
66.6
33.3
48.00741
1
1
1
1
0
200.0
66.6
33.3
48.00741
Rev 1.0, November 20, 2006
Page 12 of 20
CY28349B
Table 4. Frequency Selection Table (continued)
Input Conditions
Output Frequency
FS4
FS3
FS2
FS1
FS0
SEL4
SEL3
SEL2
SEL1
SEL0
CPU
3V66
PCI
PLL Gear
Constants
(G)
1
1
1
1
1
133.3
66.6
33.3
48.00741
Programmable Output Frequency, Watchdog
Timer and Recovery Output Frequency
Functional Description
The Programmable Output Frequency feature allows users to
generate any CPU output frequency from the range of 50 MHz
to 248 MHz. Cypress offers the most dynamic and the simplest
programming interface for system developers to utilize this
feature in their platforms.
The Watchdog Timer and Recovery Output Frequency
features allow users to implement a recovery mechanism
when the system hangs or gets unstable. System BIOS or
other control software can enable the Watchdog Timer before
they attempt to make a frequency change. If the system hangs
and a Watchdog Timer time-out occurs, a system reset will be
generated and a recovery frequency will be activated.
All of the related registers are summarized in Table 5.
Table 5. Register Summary
Name
Description
Pro_Freq_EN
Programmable output frequencies enabled
0 = Disabled (default)
1 = Enabled.
When it is disabled, the operating output frequency will be determined by either the latched value of
FS[4:0] inputs or the programmed value of SEL[4:0]. If FS_Override bit is clear, latched FS[4:0] inputs
will be used. If FS_Override bit is set, programmed value of SEL[4:0] will be used.
When it is enabled, the CPU output frequency will be determined by the programmed value of
CPUFSEL_N, CPUFSEL_M and the PLL Gear Constant. The program value of FS_Override, SEL[4:0]
or the latched value of FS[4:0] will determine the PLL Gear Constant and the frequency ratio between
CPU and other frequency outputs.
FS_Override
When Pro_Freq_EN is cleared or disabled,
0 = Select operating frequency by FS input pins (default)
1 = Select operating frequency by SEL bits in SMBus control bytes.
When Pro_Freq_EN is set or enabled,
0 = Frequency output ratio between CPU and other frequency groups and the PLL Gear Constant are
based on the latched value of FS input pins (default)
1 = Frequency output ratio between CPU and other frequency groups and the PLL Gear Constant are
based on the programmed value of SEL bits in SMBus control bytes.
CPU_FSEL_N,
CPU_FSEL_M
When Prog_Freq_EN is set or enabled, the values programmed in CPU_FSEL_N[7:0] and
CPU_FSEL_M[6:0] determines the CPU output frequency. The new frequency will start to load
whenever there is an update to either CPU_FSEL_N[7:0] or CPU_FSEL_M[6:0]. Therefore, it is recommended to use Word or Block write to update both registers within the same SMBus bus operation.
The setting of FS_Override bit determines the frequency ratio for CPU, AGP and PIC. When
FS_Override is cleared or disabled, the frequency ratio follows the latched value of the FS input pins.
When FS_Override is set or enabled, the frequency ratio follows the programmed value of SEL bits in
SMBus control bytes.
ROCV_FREQ_SEL
ROCV_FREQ_SEL determines the source of the recover frequency when a Watchdog timer time-out
occurs. The clock generator will automatically switch to the recovery CPU frequency based on the
selection on ROCV_FREQ_SEL.
0 = From latched FS[4:0]
1 = From the settings of ROCV_FREQ_N[7:0] & ROCV_FREQ_M[6:0].
ROCV_FREQ_N[7:0],
ROCV_FREQ_M[6:0]
When ROCV_FREQ_SEL is set, the values programmed in ROCV_FREQ_N[7:0] and
ROCV_FREQ_M[6:0] will be used to determine the recovery CPU output frequency when a
Watchdog Timer time-out occurs
The setting of FS_Override bit determines the frequency ratio for CPU, AGP and PIC. When it is cleared,
the same frequency ratio stated in the Latched FS[4:0] register will be used.
When it is set, the frequency ratio stated in the SEL[4:0] register will be used.
The new frequency will start to load whenever there is an update to either ROCV_FREQ_N[7:0] and
ROCV_FREQ_M[6:0]. Therefore, it is recommended to use Word or Block Write to update both
registers within the same SMBus bus operation.
WD_EN
0 = Stop and reload Watchdog Timer
1 = Enable Watchdog timer. It will start counting down after a frequency change occurs.
Rev 1.0, November 20, 2006
Page 13 of 20
CY28349B
Table 5. Register Summary (continued)
Name
Description
WD_TO_STATUS
Watchdog Timer Time-out Status bit
0 = No time-out occurs (READ); Ignore (WRITE)
1 = Time-out occurred (READ); Clear WD_TO_STATUS (WRITE).
WD_TIMER[4:0]
These bits store the time-out value of the Watchdog timer. The scale of the timer is determine by the
pre-scaler.
The timer can support a value of 150 ms to 4.8 sec when the prescaler is set to 150 ms. If the prescaler
is set to 2.5 sec, it can support a value from 2.5 sec to 80 sec.
When the Watchdog timer reaches “0”, it will set the WD_TO_STATUS bit.
WD_PRE_SCALER
0 = 150 ms
1 = 2.5 sec
RST_EN_WD
This bit will enable the generation of a Reset pulse when a Watchdog timer time-out occurs.
0 = Disabled
1 = Enabled
RST_EN_FC
This bit will enable the generation of a Reset pulse after a frequency change occurs.
0 = Disabled
1 = Enabled
Program the CPU Output Frequency
When the programmable output frequency feature is enabled
(Pro_Freq_EN bit is set), the CPU output frequency is determined by the following equation:
Fcpu = G * (N+3)/(M+3).
“N” and “M” are the values programmed in Programmable
Frequency Select N-Value Register and M-Value Register,
respectively.
“G” stands for the PLL Gear Constant, which is determined by
the programmed value of FS[4:0] or SEL[4:0]. The value is
listed in Table 4.
The ratio of (N+3) and (M+3) need to be greater than “1”
[(N+3)/(M+3) > 1].
The following table lists set of N and M values for different
frequency output ranges.This example use a fixed value for
the M-Value Register and select the CPU output frequency by
changing the value of the N-Value Register.
Table 6. Examples of N and M Value for Different CPU Frequency Range
Frequency Ranges
Gear Constants
Fixed Value for
M-Value Register
Range of N-Value Register
for Different CPU Frequency
50 MHz–129 MHz
48.00741
93
97–255
130 MHz–248 MHz
48.00741
45
127–245
Rev 1.0, November 20, 2006
Page 14 of 20
CY28349B
Maximum Ratings
Storage Temperature (Non-condensing) .....–65qC to +150qC
(Above which the useful life may be impaired. For user guidelines, not tested.)
Max. Soldering Temperature (10 sec) ....................... +260qC
Junction Temperature................................................ +150qC
Supply Voltage..................................................–0.5 to +7.0V
Package Power Dissipation.............................................. 1W
Input Voltage.............................................. –0.5V to VDD+0.5
Static Discharge Voltage ........................................................
(per MIL-STD-883, Method 3015) ............................ > 2000V
Operating Conditions Over which Electrical Parameters are Guaranteed[2]
Parameter
Description
Min.
Max.
Unit
3.135
3.465
V
0
VDD_REF, VDD_PCI,VDD_CORE,
VDD_3V66, VDD_48 MHz, VDD_CPU,
3.3V Supply Voltages
TA
Operating Temperature, Ambient
70
qC
Cin
Input Pin Capacitance
5
pF
CXTAL
XTAL Pin Capacitance
22.5
pF
CL
Max. Capacitive Load on
48MHz, REF
PCICLK, 3V66
f(REF)
Reference Frequency, Oscillator Nominal Value
pF
20
30
14.318
14.318
MHz
Electrical Characteristics Over the Operating Range
Parameter
Description
Test Conditions
Min. Max. Unit
VIH
High-level Input Voltage
Except Crystal Pads. Threshold voltage for crystal pads = VDD/2
VIL
Low-level Input Voltage
Except Crystal Pads
2.0
V
VOH
High-level Output Voltage
48MHz, REF, 3V66
IOH = –1 mA
2.4
V
PCI
IOH = –1 mA
2.4
V
0.8
V
VOL
Low-level Output Voltage
48MHz, REF, 3V66
IOL = 1 mA
PCI
IOL = 1 mA
0.55
V
IIH
Input High Current
0 < VIN < VDD
–5
5
mA
IIL
Input Low Current
0 < VIN < VDD
–5
5
mA
IOH
High-level Output Current
CPU
For IOH =6*IRef Configuration
Type X1, VOH = 0.65V
REF, 48 MHz
Type 3, VOH = 1.00V
0.4
12.9
Type X1, VOH = 0.74V
Type 5, VOH = 1.00V
–29
REF, 48MHz
Type 3, VOL = 1.95V
–23
–33
Type 5, VOH = 3.135V
IOL
Low-level Output Current
–33
29
Type 3, VOL = 0.4V
3V66, PCI,
Type 5, VOL =1.95 V
Output Leakage Current
IDD3
3.3V Power Supply Current VDD_CORE/VDD33 = 3.465V, FCPU = 133 MHz
3.3V Shutdown Current
VDD_CORE/VDDQ3 = 3.465V
IDDPD3
mA
27
30
Type 5, VOL = 0.4V
IOZ
mA
14.9
Type 3, VOH = 3.135V
3V66, PCI
V
38
Three-state
10
10
mA
250
mA
40
mA
Note:
2. Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required.
Rev 1.0, November 20, 2006
Page 15 of 20
CY28349B
-
Switching Characteristics Over the Operating Range[3]
Min.
Max.
Unit
t1
Parameter
All
Output Duty Cycle[4]
t1A/(t1B)
45
55
%
t2
CPU
Rise Time
Measured at 20% to 80% of Voh
175
700
ps
t2
48MHz, REF
Rising Edge Rate
Between 0.4V and 2.4V
0.5
2.0
V/ns
t2
PCI, 3V66,
Rising Edge Rate
Between 0.4V and 2.4V
1.0
4.0
V/ns
t3
CPU
Fall Time
Measured at 80% to 20% of Voh
175
700
ps
t3
48MHz, REF
Falling Edge Rate
Between 2.4V and 0.4V
0.5
2.0
V/ns
t3
PCI, 3V66
Falling Edge Rate
Between 2.4V and 0.4V
1.0
4.0
V/ns
t4
CPU
CPU-CPU Skew
Measured at Crossover
150
ps
t5
3V66 [0:1]
3V66-3V66 Skew
Measured at 1.5V
500
ps
t6
PCI
PCI-PCI Skew
Measured at 1.5V
500
ps
t7
3V66,PCI
3V66-PCI Clock Skew
3V66 leads. Measured at 1.5V
3.5
ns
t8
CPU
Cycle-Cycle Clock Jitter
Measured at Crossover t8 = t8A – t8B
With all outputs running
200
ps
t9
3V66
Cycle-Cycle Clock Jitter
Measured at 1.5V t9 = t9A – t9B
250
ps
t9
48MHz
Cycle-Cycle Clock Jitter
Measured at 1.5V t9 = t9A – t9B
350
ps
t9
PCI
Cycle-Cycle Clock Jitter
Measured at 1.5V t9 = t9A – t9B
500
ps
t9
REF
Cycle-Cycle Clock Jitter
Measured at 1.5V t9 = t9A – t9B
1000
ps
CPU, PCI
Settle Time
CPU and PCI clock stabilization from
power-up
3
ms
CPU
Rise/Fall Matching
Measured with test loads[5, 6]
Voh
Output
Description
Test Conditions
1.5
20%
loads[6]
CPU
Overshoot
Measured with test
CPU
Undershoot
Measured with test loads[6]
–0.2
Measured with test
loads[6]
0.65
0.74
V
loads[6]
0.0
0.05
V
CPU
High-level Output Voltage
Vol
CPU
Low-level Output Voltage
Measured with test
Vcrossover
CPU
Crossover Voltage
Measured with test loads[6]
Voh +
0.2
V
V
45% of 55% of
0.65
0.74
V
Notes:
3. All parameters specified with loaded outputs.
4. Duty cycle is measured at 1.5V when VDD = 3.3V. When VDD = 2.5V, duty cycle is measured at 1.25V.
5. Determined as a fraction of 2*(Trp – Trn)/(Trp + Trn) Where Trp is a rising edge and Trn is an intersecting falling edge.
6. The test load is Rs = 33.2:, Rp = 49.9: in test circuit.
Rev 1.0, November 20, 2006
Page 16 of 20
CY28349B
Switching Waveforms
Duty Cycle Timing (Single-ended Output)
t1B
t1A
Duty Cycle Timing (CPU Differential Output)
t1B
t1A
All Outputs Rise/Fall Time
VDD
OUTPUT
0V
t3
t2
CPU-CPU Clock Skew
Host_b
Host
Host_b
Host
t4
3V66-3V66 Clock Skew
3V66
3V66
t5
PCI-PCI Clock Skew
PCI
PCI
t6
Rev 1.0, November 20, 2006
Page 17 of 20
CY28349B
Switching Waveforms (continued)
3V66-PCI Clock Skew
3V66
PCI
t7
CPU Clock Cycle-Cycle Jitter
t8A
t8B
Host_b
Host
Cycle-Cycle Clock Jitter
t9A
t9B
CLK
Rev 1.0, November 20, 2006
Page 18 of 20
CY28349B
Layout Example
+3.3V Supply
FB
VDDQ3
0.005PF
G
G
G
G
VDDQ3
5:
48
47
V
46
G
45
44
G 43
42
41
G 40
V 39
G
38
37
G
36
G 35
V 34
G
3
V
32
G
31
30
G 29
28
27
26
G 25
G
CY28349B
1
2 VG
3
4
5 G
6
7
8 G
9 V
G
10
11
12
13 G
14
15
16
17 G
18 V
19 G
20
21 G
22
23
24 *
G
C5 G
C3
G
G
G
G
G
G
G C6
FB = Dale ILB1206 - 300 (300:@ 100 MHz)
C4 = 0.005 PF
Ceramic Caps C3 = 10–22 PF
G = VIA to GND plane layer
C5 = 10 PF
C6 = 0.1 PF
V =VIA to respective supply plane layer
Note: Each supply plane or strip should have a ferrite bead and capacitors
All bypass caps = 0.1 PF ceramic
* For use with onboard video using 48 MHz for Dot Clock or connect to VDDQ3
Rev 1.0, November 20, 2006
Page 19 of 20
CY28349B
Ordering Information
Ordering Code
Package Type
Operating Range
CY28349BOC
48-pin SSOP
Commercial, 0°C to 70°C
CY28349BOCT
48-pin SSOP – Tape and Reel
Commercial, 0°C to 70°C
CY28349BOXC
48-pin SSOP
Commercial, 0°C to 70°C
CY28349BOXCT
48-pin SSOP – Tape and Reel
Commercial, 0°C to 70°C
Lead-free
Package Diagram
48-lead Shrunk Small Outline Package O48
While SLI has reviewed all information herein for accuracy and reliability, Spectra Linear Inc. assumes no responsibility for the use of any circuitry or for the infringement of any patents or other rights of third parties which would result from each use. This product is intended for use in
normal commercial applications and is not warranted nor is it intended for use in life support, critical medical instruments, or any other application requiring extended temperature range, high reliability, or any other extraordinary environmental requirements unless pursuant to additional
processing by Spectra Linear Inc., and expressed written agreement by Spectra Linear Inc. Spectra Linear Inc. reserves the right to change any
circuitry or specification without notice.
Rev 1.0, November 20, 2006
Page 20 of 20
Similar pages