Sharp GP1A73A Compact opic photointerrupter with connector Datasheet

GP1A73A/GP1A73A1
GP1A73A/GP1A73A1
Compact OPIC Photointerrupter
with Connector
■ Features
■ Outline Dimensions
1. Compact type
2. TTL compatible owing to OPIC output
(Unit : mm)
GP1A73A
2.3
(Sensor center)
4. 3 kinds of mounting plate thickness
(Applicable plate thickness : 1.0, 1.2 and 1.6 mm)
7.8
73
SHARP
8.0
3. Snap-in mounting type
JAPAN
( 6.8)
JAPAN AMP made
connector 175487-3
(Case surface)
13.6
4.7
1.6
2-0.5 ± 0.1
(Slit)
6.8 ± 1
2.4
2.3
1.1
2. Laser beam printers
3. Facsimiles
0.6
0.2
2.3
1. Copiers
5.4
14.0
16.8
17.0
0.75
2-0.5 4.0
* Unspecified tolerances
shall be as follows.
* ( ) : Connector dimensions
for reference
6.9
9.9
11.4
1.2
2-0.9
1.1
5.6
■ Applications
1 : VCC
2 : Vout
3 : GND
5.8
7.2
3.2
4.3 5.0 4.3
Dimension
d < 5.0
5.0<= d < 15.0
15.0 <= d
Tolerance
± 0.15
± 0.2
± 0.3
GP1A73A1
2.3
(Sensor center)
73
8.0
HIROSE made
connector DF3A-3P-2DSA
(Case surface)
13.6
4.7
1.6
2-0.5 ± 0.1
(Slit)
5.0 ± 1
3.2
4.3 5.0 4.3
3 : VCC
2 : Vout
1 : GND
*1
*2
*3
*3
*1 Output transistor collector-emitter voltage
*2 Output transistor collector current
*3 The connector should be plugged in/out at normal temperature.
Unit
V
V
mA
˚C
˚C
2.4
5.4
6.9
9.9
11.4
14.0
16.8
17.0
1.2
0.75
2-0.9
1.1
(Ta=25˚C)
Rating
- 0.5 to + 7
- 0.5 to + 7
8
- 20 to + 75
- 30 to + 85
2.3
Symbol
V CC
V out
I OL
T opr
T stg
1.1
Parameter
Supply voltage
Output voltage
Low level output current
Operating temperature
Storage temperature
0.6
0.2
2.3
■ Absolute Maximum Ratings
5.6
5
7.2
* "OPIC" (Optical IC) is a trademark of the SHARP Corporation.
An OPIC consists of a light-detecting element and signal-processing circuit
integrated onto a single chip.
SHARP
8.0
JAPAN
( 5)
2-0.5 4.0
* Unspecified tolerances
shall be as follows.
* ( ) : Connector dimensions
for reference
Dimension
d < 5.0
5.0<= d < 15.0
15.0 <= d
Tolerance
± 0.15
± 0.2
± 0.3
■ Internal Connection Diagram (Both GP1A73A/GP1A73A1)
Constant
voltage circuit
GND
Vout
Connector terminal No.
GP1A73A GP1A73A1
3 : GND 1 : GND
2 : Vout 2 : Vout
1 : Vcc
3 : Vcc
Amp.
Vcc
* GP1A73A and GP1A73A1 are different in the terminal marking number of
connectors from each other due to use of connectors of different manufacturers.
“ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs,
data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.”
GP1A73A/GP1A73A1
■ Electro-optical Characteristics
(VCC =5v, Ta=25 ˚C unless otherwise specified)
Parameter
Operating supply voltage
Current consumption
Low level output voltage
Current consumption
High level output voltage
Symbol
V CC
I CCL
V OL
I CCH
V OH
MIN. interruption time
Response
Conditions
MIN.
4.5
Light beam uninterrupted
Light beam uninterrupted, I OL =4mA
Light beam interrupted
Light beam interrupted, RL =47k Ω V CC x 0.9
tH
MIN. sensing time
tL
Fig. 1 Output Current vs. Ambient
Temperature
166
-
-
µs
166
-
-
µs
Low level output voltage V OL ( V)
1.0
(mA)
8
OL
Unit
V
mA
V
mA
V
Fig. 2 Low Level Output Voltage vs.
Low Level Output Current
10
Output current I
MAX.
5.5
16.5
0.35
16.5
-
R L = 4.7kΩ
characteristics
6
4
2
0
- 20
TYP.
-
V CC = 5V
T a = 25˚C
0.5
0.2
0.1
0.05
0.02
0.01
0
25
50
1
75
2
5
10
50
20
100
Low level output current I OL ( mA)
Ambient temperature Ta (˚C)
Fig. 3 Low Level Output Voltage vs.
Ambient Temperature
Fig. 4 Supply Current vs. Supply Voltage
20
0.2
CC ( mA)
I OL = 6mA
Supply current I
Low level output voltage V OL ( V)
V CC = 5V
4mA
0.1
2mA
0
- 25
0
25
50
75
- 20 Ambient temperature Ta (˚C)
100
- 20˚CI CCL
- 20˚CI CCH
+25˚CI CCL
+25˚CI CCH
10
+75˚CI CCL
+75˚CI CCH
0
4.5
5.0
Supply voltage V CC ( V)
5.5
GP1A73A/GP1A73A1
Fig. 5 Detecting Position Characteristics (1)
Fig. 6 Detecting Position Characteristics (2)
Output "High"
Output "High"
VCC= 5V, Ta= 25˚C
RL= 47kΩ
Detecting position
characteristics
( d= 2.35± 0.3mm )
d0
VCC= 5V
Ta= 25˚C
RL= 47kΩ
Detecting position
characteristics
( h= 3.0 + 0.3 )
- 1.8
Shield plate
Shield plate
0
h
Output "Low"
Output "Low"
0
1
2
3
4
5
0
1
2
Distance d (mm)
3
4
5
Distance h (mm)
■ Recommended Mounting Hole Shape
(Unit : mm)
8 - R0.1± 0.1
8 - R0.1± 0.1
7.7
17
3.5
6
7.5
17
General mounting type
17
7.5
6
3.5
8 - R0.1± 0.1
7.5
Plate thickness : 1.6 mm
7.5
Plate thickness : 1.2 mm
12 - R0.1± 0.1
12 - R0.1± 0.1
2.4
2.4
2.4
7.7
Plate thickness : 1.6 mm
2.4
7.5
Plate thickness : 1.2 mm
3.5
6
7.5
preventive type
17
17
Reverse insertion
17
7.5
6
3.5
12 - R0.1± 0.1
Plate thickness : 1.0 mm
2.4
2.4
7.5
Plate thickness : 1.0 mm
1. It is recommended to mark the shear droop surface (punch side) of the mounting plate (metal plate) with "GP1A73A" or "GP1A73A1".
2. Mounting workability, shaking after mounting and mounting strength depend on the corner radius of the mounting plate and state of punching.
Determine the mounting dimensions after check on an actual machine.
3. General dimensional tolerances shall be ± 0.1 mm.
GP1A73A/GP1A73A1
(Precautions for Operation)
1) In this product, the PWB is fixed with a hook, and cleaning solvent may remain inside the case;
therefore, dip cleaning or ultrasonic cleaning are prohibited.
2) Remove dust or stains, using an air blower or a soft cloth moistened in cleaning solvent.
However, do not perform the above cleaning using a soft cloth with solvent in the marking portion.
In this case, use only the following type of cleaning solvent for wiping off;
Ethyl alcohol, Methyl alcohol, Isopropyl alcohol,
When the cleaning solvents except for specified materials are used, please contact us.
3) In order to stabilize power supply line, connect a by-pass capacitor of more than 0.01µ F between VCC and GND
near the device.
● As for other general precautions, please refer to the chapter "Precautions for Use".
Similar pages