M470L1714BT0 200pin DDR SDRAM SODIMM 128MB DDR SDRAM MODULE (16Mx64 based on 8Mx16 DDR SDRAM) 200pin SODIMM 64-bit Non-ECC/Parity Revision 0.1 June. 2001 Rev. 0.1 June. 2001 M470L1714BT0 200pin DDR SDRAM SODIMM Revision History Revision 0.0 (Apr. 2001) 1. First release. Revision 0.1 (June. 2001) 1. Changed module current speificaton 2. Changed typo size on module PCB in package dimesions. (from 2.6mm to 3mm). 3. Changed AC parameter table. Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 M470L1714BT0 200pin DDR SDRAM SODIMM 16Mx64 200pin DDR SDRAM SODIMM based on 8Mx16 FEATURE GENERAL DESCRIPTION The Samsung M470L1714BT0 is 16M bit x 64 Double Data • Performance range Part No. Rate SDRAM high density memory modules based on first gen Max Freq. Interface of 128Mb DDR SDRAM respectively. M470L1714BT0-C(L)A2 133MHz(7.5ns@CL=2) The Samsung M470L1714BT0 consists of eight CMOS 8M x M470L1714BT0-C(L)B0 133MHz(7.5ns@CL=2.5) 16 bit with 4banks Double Data Rate SDRAMs in 66pin TSOP- M470L1714BT0-C(L)A0 100MHz(10ns@CL=2) II(400mil) packages mounted on a 200pin glass-epoxy substrate. Four 0.1uF decoupling capacitors are mounted on the printed circuit board in parallel for each DDR SDRAM. The M470L1714BT0 is Dual In-line Memory Modules and intended for mounting into 200pin edge connector sockets. Synchronous design allows precise cycle control with the use of system clock. Data I/O transactions are possible on both edges of DQS. Range of operating frequencies, programmable latencies and burst lengths allow the same device to be useful for a variety of high bandwidth, high performance memory system applications. • Power supply : Vdd: 2.5V ± 0.2V, Vddq: 2.5V ± 0.2V • Double-data-rate architecture; two data transfers per clock cycle • Bidirectional data strobe(DQS) • Differential clock inputs(CK and CK) • DLL aligns DQ and DQS transition with CK transition • Programmable Read latency 2, 2.5 (clock) • Programmable Burst length (2, 4, 8) • Programmable Burst type (sequential & interleave) • Edge aligned data output, center aligned data input • Auto & Self refresh, 15.6us refresh interval(4K/64ms refresh) • Serial presence detect with EEPROM • PCB : Height 1250 (mil), double sided component PIN DESCRIPTION PIN CONFIGURATIONS (Front side/back side) Pin Front 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 VREF VSS DQ0 DQ1 VDD DQS0 DQ2 VSS DQ3 DQ8 VDD DQ9 DQS1 VSS DQ10 DQ11 VDD CK0 /CK0 VSS Key DQ16 DQ17 VDD DQS2 DQ18 VSS DQ19 DQ24 VDD DQ25 DQS3 VSS DQ26 41 43 45 47 49 51 53 55 57 59 61 63 65 Pin Front Pin Front DQ34 DQ27 135 67 VSS 137 VDD 69 DQ35 139 CB0 71 DQ40 141 CB1 73 VDD 143 VSS 75 DQ41 DQS8 145 77 DQS5 147 CB2 79 VSS 149 VDD 81 DQ42 151 CB3 83 DQ43 153 DU 85 VDD 155 VSS 87 VDD 157 CK2 89 VSS 159 /CK2 91 VSS 161 VDD 93 DQ48 CKE1 163 95 DQ49 97 DU(A13) 165 VDD 167 A12 99 DQS6 169 A9 101 DQ50 171 VSS 103 VSS 173 A7 105 DQ51 175 A5 107 DQ56 177 A3 109 VDD 179 A1 111 DQ57 181 VDD 113 DQS7 115 A10/AP 183 VSS 185 BA0 117 DQ58 187 /WE 119 DQ59 189 /S0 121 VDD 191 DU 123 SDA 193 VSS 125 SCL 127 DQ32 195 129 DQ33 197 VDDSPD 199 VDDID VDD 131 133 DQS4 Pin Back 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 VREF VSS DQ4 DQ5 VDD DM0 DQ6 VSS DQ7 DQ12 VDD DQ13 DM1 VSS DQ14 DQ15 VDD VDD VSS VSS Key DQ20 DQ21 VDD DM2 DQ22 VSS DQ23 DQ28 VDD DQ29 DM3 VSS DQ30 42 44 46 48 50 52 54 56 58 60 62 64 66 Pin Back SSTL_2 Pin Back 136 DQ31 68 138 VDD 70 140 CB4 72 142 CB5 74 144 VSS 76 146 DM8 78 148 CB6 80 150 VDD 82 152 CB7 84 86 DU/(RESET) 154 156 VSS 88 158 VSS 90 160 VDD 92 162 VDD 94 164 CKE0 96 166 DU(BA2) 98 168 A11 100 170 A8 102 172 VSS 104 174 A6 106 176 A4 108 178 A2 110 180 A0 112 182 VDD 114 184 BA1 116 186 /RAS 118 188 /CAS 120 190 /S1 122 192 DU 124 194 VSS 126 196 DQ36 128 198 DQ37 130 200 VDD 132 DM4 134 DQ38 VSS DQ39 DQ44 VDD DQ45 DM5 VSS DQ46 DQ47 VDD /CK1 CK1 VSS DQ52 DQ53 VDD DM6 DQ54 VSS DQ55 DQ60 VDD DQ61 DM7 VSS DQ62 DQ63 VDD SA0 SA1 SA2 DU Pin Name * Function A0 ~ A11 Address input (Multiplexed) BA0 ~ BA1 Bank Select Address DQ0 ~ DQ63 Data input/output DQS0 ~ DQS7 Data Strobe input/output CK0~ CK2, CK0~ CK2 Clock input CKE0 Clock enable input CS0 Chip select input RAS Row address strobe CAS Column address strobe WE Write enable DM0 ~ DM7 Data - in mask VDD Power supply (2.5V) VDDQ Power Supply for DQS(2.5V) VSS Ground VREF Power supply for reference VDDSPD Serial EEPROM Power Supply (2.3V to 3.6V) SDA Serial data I/O SCL Serial clock SA0 ~ 2 Address in EEPROM VDDID VDD identification flag NC No connection These pins are not used in this module. SAMSUNG ELECTRONICS CO., Ltd. reserves the right to change products and specifications without notice. Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 FUNCTIONAL BLOCK DIAGRAM S1 S0 DQS0 DM0 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 LDQS LDM I/0 0 I/0 1 I/0 2 I/0 3 I/0 4 I/0 5 I/0 6 I/0 7 DQS1 DM1 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 UDQS UDM I/0 8 I/0 9 I/0 10 I/0 11 I/0 12 I/0 13 I/0 14 I/0 15 DQS2 DM2 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 LDQS LDM I/0 0 I/0 1 I/0 2 I/0 3 I/0 4 I/0 5 I/0 6 I/0 7 DQS3 DM3 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 UDQS UDM I/0 8 I/0 9 I/0 10 I/0 11 I/0 12 I/0 13 I/0 14 I/0 15 S D0 S D1 BA0 - BA1 BA0-BA1: DDR SDRAMs D0 - D7 A0 - A13 A0-A13: DDR SDRAMs D0 - D7 RAS RAS: SDRAMs D0 - D7 CAS CAS: SDRAMs D0 - D7 CKE0 CKE: SDRAMs D0 - D7 WE WE: SDRAMs D0 - D7 VDDSPD VDD/VDDQ VREF VSS VDDID LDQS S LDM I/0 0 I/0 1 I/0 2 D4 I/0 3 I/0 4 I/0 5 I/0 6 I/0 7 DQS4 DM4 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 LDQS LDM I/0 0 I/0 1 I/0 2 I/0 3 I/0 4 I/0 5 I/0 6 I/0 7 UDQS UDM I/0 8 I/0 9 I/0 10 I/0 11 I/0 12 I/0 13 I/0 14 I/0 15 DQS5 DM5 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 UDQS UDM I/0 8 I/0 9 I/0 10 I/0 11 I/0 12 I/0 13 I/0 14 I/0 15 LDQS S LDM I/0 0 I/0 1 I/0 2 D5 I/0 3 I/0 4 I/0 5 I/0 6 I/0 7 DQS6 DM6 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 LDQS LDM I/0 0 I/0 1 I/0 2 I/0 3 I/0 4 I/0 5 I/0 6 I/0 7 UDQS UDM I/0 8 I/0 9 I/0 10 I/0 11 I/0 12 I/0 13 I/0 14 I/0 15 DQS7 DM7 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 UDQS UDM I/0 8 I/0 9 I/0 10 I/0 11 I/0 12 I/0 13 I/0 14 I/0 15 LDQS S LDM I/0 0 I/0 1 I/0 2 D7 I/0 3 I/0 4 I/0 5 I/0 6 I/0 7 D3 UDQS UDM I/0 8 I/0 9 I/0 10 I/0 11 I/0 12 I/0 13 I/0 14 I/0 15 R=120Ω ± 5% SDRAMs CK CK 4 SDRAMs 4 SDRAMs NC Card Edge *Clock Net Wiring Serial PD SCL D0 - D7 WP D0 - D7 UDQS UDM I/0 8 I/0 9 I/0 10 I/0 11 I/0 12 I/0 13 I/0 14 I/0 15 S Clock Wiring Clock Input CK0/CK0 CK1/CK1 CK2/CK2 SPD Strap: see Note 4 D2 Dram1 D0 - D7 D0 - D7 LDQS S LDM I/0 0 I/0 1 I/0 2 D6 I/0 3 I/0 4 I/0 5 I/0 6 I/0 7 S SDA A0 A1 A2 SA0 SA1 SA2 Dram2 Dram3 Dram4 Notes: 1. DQ-to-I/O wiring is shown as recommended but may be changed. 2. DQ/DQS/DM/CKE/CS relationships must be maintained as shown. 3. DQ, DQS, DM/DQS resistors: 22 Ohms. 4. VDDID strap connections (for memory device VDD, VDDQ): STRAP OUT (OPEN): VDD = VDDQ STRAP IN (VSS): VDD ≠ VDDQ. Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin relative to Vss Symbol Value Unit VIN, VOUT -0.5 ~ 3.6 V VDD -1.0 ~ 3.6 V Voltage on VDD supply relative to Vss Voltage on VDDQ supply relative to Vss VDDQ -0.5 ~ 3.6 V Storage temperature TSTG -55 ~ +150 °C Power dissipation PD 8 W Short circuit current IOS 50 mA Note : Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. POWER & DC OPERATING CONDITIONS (SSTL_2 In/Out) Recommended operating conditions(Voltage referenced to VSS=0V, TA=0 to 70°C) Parameter Symbol Min Max Supply voltage(for device with a nominal VDD of 2.5V) VDD 2.3 2.7 I/O Supply voltage VDDQ 2.3 2.7 I/O Reference voltage VREF VDDQ/2-50mV VDDQ/2+50mV V 1 I/O Termination voltage(system) VTT VREF-0.04 VREF+0.04 V 2 Input logic high voltage VIH(DC) VREF+0.15 VDDQ+0.3 V 4 Input logic low voltage VIL(DC) -0.3 VREF-0.15 V 4 Input Voltage Level, CK and CK inputs VIN(DC) -0.3 VDDQ+0.3 V Input Differential Voltage, CK and CK inputs VID(DC) 0.3 VDDQ+0.6 V 3 Input crossing point voltage, CK and CK inputs VIX(DC) 1.15 1.35 V 5 II -2 2 uA Output leakage current IOZ -5 5 uA Output High Current(Normal strengh driver) ;VOUT = VTT + 0.84V IOH -16.8 mA Output High Current(Normal strengh driver) ;VOUT = VTT - 0.84V IOL 16.8 mA Output High Current(Half strengh driver) ;VOUT = VTT + 0.45V IOH -9 mA Output High Current(Half strengh driver) ;VOUT = VTT - 0.45V IOL 9 mA Input leakage current Unit Note V Notes 1. Includes ± 25mV margin for DC offset on VREF, and a combined total of ± 50mV margin for all AC noise and DC offset on V REF, bandwidth limited to 20MHz. The DRAM must accommodate DRAM current spikes on VREF and internal DRAM noise coupled TO VREF, both of which may result in VREF noise. VREF should be de-coupled with an inductance of ≤ 3nH. 2.VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF, and must track variations in the DC level of VREF 3. VID is the magnitude of the difference between the input level on CK and the input level on CK. 4. These parameters should be tested at the pin on actual components and may be checked at either the pin or the pad in simulation. The AC and DC input specifications are relative to a VREF envelop that has been bandwidth limited to 200MHZ. 5. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the dc level of the same. 6. These charactericteristics obey the SSTL-2 class II standards. Rev. 0.1 June. 2001 M470L1714BT0 200pin DDR SDRAM SODIMM DDR SDRAM SPEC Items and Test Conditions Recommended operating conditions Unless Otherwise Noted, TA=0 to 70°C) Conditions Symbol Typical Worst Operating current - One bank Active-Precharge; tRC=tRCmin;tCK=100Mhz for DDR200, 133Mhz for DDR266A & DDR266B; DQ,DM and DQS inputs changing twice per clock cycle; address and control inputs changing once per clock cycle IDD0 - - Operating current - One bank operation ; One bank open, BL=4, Reads - Refer to the following page for detailed test condition IDD1 - - Percharge power-down standby current; All banks idle; power - down mode; CKE = <VIL(max); tCK=100Mhz for DDR200, 133Mhz for DDR266A & DDR266B; Vin = Vref for DQ,DQS and DM IDD2P - - Precharge Floating standby current; CS# > =VIH(min);All banks idle; CKE > = VIH(min); tCK=100Mhz for DDR200, 133Mhz for DDR266A & DDR266B; Address and other control inputs changing once per clock cycle; Vin = Vref for DQ,DQS and DM IDD2F - - Precharge Quiet standby current; CS# > = VIH(min); All banks idle; CKE > = VIH(min); tCK = 100Mhz for DDR200, 133Mhz for DDR266A & DDR266B; Address and other control inputs stable with keeping >= VIH(min) or =<VIL(max); Vin = Vref for DQ ,DQS and DM IDD2Q - - Active power - down standby current ; one bank active; power-down mode; CKE=< VIL (max); tCK = 100Mhz for DDR200, 133Mhz for DDR266A & DDR266B; Vin = Vref for DQ,DQS and DM IDD3P - - Active standby current; CS# >= VIH(min); CKE>=VIH(min); one bank active; active - precharge; tRC=tRASmax; tCK = 100Mhz for DDR200, 133Mhz for DDR266A & DDR266B; DQ, DQS and DM inputs changing twice per clock cycle; address and other control inputs changing once per clock cycle IDD3N - - Operating current - burst read; Burst length = 2; reads; continguous burst; One bank active; address and control inputs changing once per clock cycle; CL=2 at tCK = 100Mhz for DDR200, CL=2 at tCK = 133Mhz for DDR266A, CL=2.5 at tCK = 133Mhz for DDR266B ; 50% of data changing at every burst; lout = 0 m A IDD4R - - Operating current - burst write; Burst length = 2; writes; continuous burst; One bank active address and control inputs changing once per clock cycle; CL=2 at tCK = 100Mhz for DDR200, CL=2 at tCK = 133Mhz for DDR266A, CL=2.5 at tCK = 133Mhz for DDR266B ; DQ, DM and DQS inputs changing twice per clock cycle, 50% of input data changing at every burst IDD4W - - Auto refresh current; tRC = tRFC(min) - 8*tCK for DDR200 at 100Mhz, 10*tCK for DDR266A & DDR266B at 133Mhz; distributed refresh IDD5 - - Self refresh current; CKE =< 0.2V; External clock should be on; tCK = 100Mhz for DDR200, 133Mhz for DDR266A & DDR266B IDD6 - - Orerating current - Four bank operation ; Four bank interleaving with BL=4 -Refer to the following page for detailed test condition IDD7A - - Typical case: VDD = 2.5V, T = 25’C Worst case : VDD = 2.7V, T = 10’C Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 DDR SDRAM module IDD spec table Symbol IDD6 typical worst B0(DDR266@CL=2.5) typical worst A0(DDR200@CL=2) typical worst Unit IDD0 620 680 620 680 540 580 mA IDD1 720 800 720 800 640 720 mA IDD2P 320 340 304 340 260 280 mA mA IDD2F 420 460 380 460 360 380 IDD2Q 380 400 340 400 320 340 mA IDD3P 360 380 320 380 300 320 mA IDD3N 440 480 400 480 360 400 mA IDD4R 940 1060 940 1060 780 920 mA IDD4W 980 1120 980 1120 820 980 mA IDD5 980 1080 980 1080 900 980 mA 16 16 16 16 16 16 mA Normal Low power IDD7A * Module A2(DDR266@CL=2) 8 8 8 8 8 8 mA 1600 1820 1600 1820 1300 1500 mA IDD was calculated on the basis of component IDD and Notes Optional can be differently measured according to DQ loading cap. < Detailed test conditions for DDR SDRAM IDD1 & IDD7A > IDD1 : Operating current: One bank operation 1. Typical Case : Vdd = 2.5V, T=25’C 2. Worst Case : Vdd = 2.7V, T= 10’C 3. Only one bank is accessed with tRC(min), Burst Mode, Address and Control inputs on NOP edge are changing once per clock cycle. lout = 0mA 4. Timing patterns - DDR200(100Mhz, CL=2) : tCK = 10ns, CL2, BL=4, tRCD = 2*tCK, tRAS = 5*tCK Read : A0 N R0 N N P0 N A0 N - repeat the same timing with random address changing *50% of data changing at every burst - DDR266B(133Mhz, CL=2.5) : tCK = 7.5ns, CL=2.5, BL=4, tRCD = 3*tCK, tRC = 9*tCK, tRAS = 5*tCK Read : A0 N N R0 N P0 N N N A0 N - repeat the same timing with random address changing *50% of data changing at every burst - DDR266A (133Mhz, CL=2) : tCK = 7.5ns, CL=2, BL=4, tRCD = 3*tCK, tRC = 9*tCK, tRAS = 5*tCK Read : A0 N N R0 N P0 N N N A0 N - repeat the same timing with random address changing *50% of data changing at every burst Legend : A=Activate, R=Read, W=Write, P=Precharge, N=NOP Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 IDD7A : Operating current: Four bank operation 1. Typical Case : Vdd = 2.5V, T=25’C 2. Worst Case : Vdd = 2.7V, T= 10’C 3. Four banks are being interleaved with tRC(min), Burst Mode, Address and Control inputs on NOP edge are not changing. lout = 0mA 4. Timing patterns - DDR200(100Mhz, CL=2) : tCK = 10ns, CL2, BL=4, tRRD = 2*tCK, tRCD= 3*tCK, Read with autoprecharge Read : A0 N A1 R0 A2 R1 A3 R2 A0 R3 A1 R0 - repeat the same timing with random address changing *100% of data changing at every burst - DDR266B(133Mhz, CL=2.5) : tCK = 7.5ns, CL=2.5, BL=4, tRRD = 2*tCK, tRCD = 3*tCK Read with autoprecharge Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing *100% of data changing at every burst - DDR266A (133Mhz, CL=2) : tCK = 7.5ns, CL2=2, BL=4, tRRD = 2*tCK, tRCD = 3*tCK Read : A0 N A1 R0 A2 R1 A3 R2 N R3 A0 N A1 R0 - repeat the same timing with random address changing *100% of data changing at every burst Legend : A=Activate, R=Read, W=Write, P=Precharge, N=NOP AC Operating Conditions Parameter/Condition Symbol Min Input High (Logic 1) Voltage, DQ, DQS and DM signals VIH(AC) Input Low (Logic 0) Voltage, DQ, DQS and DM signals. VIL(AC) Input Differential Voltage, CK and CK inputs VID(AC) 0.7 Input Crossing Point Voltage, CK and CK inputs VIX(AC) 0.5*VDDQ-0.2 Max VREF + 0.31 Unit Note V 3 VREF - 0.31 V 3 VDDQ+0.6 V 1 0.5*VDDQ+0.2 V 2 Note 1. VID is the magnitude of the difference between the input level on CK and the input on CK. 2. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the DC level of the same. 3. These parameters should be tested at the pim on actual components and may be checked at either the pin or the pad in simulation. the AC and DC input specificatims are refation to a Vref envelope that has been bandwidth limited 20MHz. Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 AC OPERATING TEST CONDITIONS (VDD=2.5V, VDDQ=2.5V, TA= 0 to 70°C) Parameter Value Unit Input reference voltage for Clock 0.5 * VDDQ V Input signal maximum peak swing 1.5 V VREF+0.31/VREF-0.31 V VREF V Vtt V Input Levels(VIH/VIL) Input timing measurement reference level Output timing measurement reference level Output load condition Note See Load Circuit Vtt=0.5*VDDQ RT=50Ω Output Z0=50Ω VREF =0.5*VDDQ CLOAD=30pF Output Load Circuit (SSTL_2) Input/Output CAPACITANCE (VDD=2.5V, VDDQ=2.5V, TA= 25°C, f=1MHz) Parameter Symbol Min Max Unit Input capacitance(A0 ~ A11, BA0 ~ BA1,RAS,CAS, WE ) CIN1 36 44 pF Input capacitance(CKE0) CIN2 36 44 pF Input capacitance( CS0, CS1) CIN3 26 30 pF Input capacitance( CLK0, CLK1) CIN4 34 38 pF Data & DQS input/output capacitance(DQ0~DQ63) COUT 12 14 pF Input capacitance(DM0~DM8) CIN5 12 14 pF Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 AC Timming Parameters & Specifications (These AC charicteristics were tested on the Component) Parameter Symbol Row cycle time -TCA2(DDR266A) -TCB0(DDR266B) Min Max Min Max -TCA0 (DDR200) Min Max Unit tRC 65 65 70 Refresh row cycle time tRFC 75 75 80 Row active time tRAS 45 RAS to CAS delay tRCD 20 20 20 ns tRP 20 20 20 ns Row active to Row active delay tRRD 15 15 15 ns Write recovery time tWR 2 2 2 tCK tCDLR 1 1 1 tCK Row precharge time Last data in to Read command Col. address to Col. address delay Clock cycle time tCCD CL=2.0 CL=2.5 tCK 120K 1 45 120K 1 ns ns 48 120K 1 7.5 12 10 12 7.5 12 7.5 12 ns tCK 10 12 ns 5 12 ns 5 Clock high level width tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK Clock low level width tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK ns DQS-out access time from CK/CK tDQSCK -0.75 +0.75 -0.75 +0.75 -0.8 +0.8 Output data access time from CK/CK tAC -0.75 +0.75 -0.75 +0.75 -0.8 +0.8 ns Data strobe edge to ouput data edge tDQSQ - +0.5 - +0.5 - +0.6 ns Read Preamble tRPRE 0.9 1.1 0.9 1.1 0.9 1.1 tCK Read Postamble tRPST 0.4 0.6 0.4 0.6 0.4 0.6 tCK CK to valid DQS-in tDQSS 0.75 1.25 0.75 1.25 0.75 1.25 tCK DQS-in setup time tWPRES 0 0 0 ns DQS-in hold time tWPREH 0.25 0.25 0.25 tCK DQS falling edge to CK rising-setup time tDSS 0.2 0.2 0.2 tCK DQS falling edge from CK rising-hold time tDSH 0.2 0.2 0.2 tCK DQS-in high level width tDQSH 0.35 0.35 0.35 tCK DQS-in low level width tDQSL 0.35 0.35 0.35 tCK DQS-in cycle time 0.9 1.1 0.9 tIS 0.9 0.9 1.1 ns 6 Address and Control Input hold time tIH 0.9 0.9 1.1 ns 6 Data-out high impedence time from CK/CK tHZ tACmin 400ps tACmax - 400ps tACmin - 400ps tACmax - 400ps tACmin - 400ps tACmax - 400ps ps Data-out low impedence time from CK/CK tLZ tACmin 400ps tACmax - 400ps tACmin - 400ps tACmax - 400ps tACmin - 400ps tACmax - 400ps ps tSL(I) 0.5 Input Slew Rate(for I/O pins) tSL(IO) 0.5 Output Slew Rate(x4,x8) tSL(O) 1.0 Output Slew Rate(x16) tSL(O) 0.7 5 0.7 5 Output Slew Rate Matching Ratio(rise to fall) tSLMR 0.67 1.5 0.67 1.5 0.5 0.5 4.5 1.0 1.1 2 tDSC 0.5 0.9 5 Address and Control Input setup time Input Slew Rate(for input only pins) 1.1 Note V/ns 0.5 4.5 tCK 6 V/ns 7 4.5 V/ns 10 0.7 5 V/ns 10 0.67 1.5 1.0 Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 Parameter Mode register set cycle time Symbol -TCA2(DDR266A) Min Max -TCB0(DDR266B) Min Max -TCA0 (DDR200) Min Max Unit Note tMRD 15 15 16 ns DQ & DM setup time to DQS tDS 0.5 0.5 0.6 ns 7,8,9 DQ & DM hold time to DQS tDH 0.5 0.5 0.6 ns 7,8,9 DQ & DM input pulse width tDIPW 1.75 1.75 2 ns Power down exit time tPDEX 10 10 10 ns Exit self refresh to write command tXSW 95 116 ns Exit self refresh to bank active command tXSA 75 75 80 ns Exit self refresh to read command tXSR 200 200 200 Cycle tREF 15.6 15.6 15.6 us 1 7.8 7.8 7.8 us 1 - tHPmin -tQHS - tHPmin -tQHS - ns 5 - tCLmin or tCHmin - tCLmin or tCHmin - ns Refresh interval time 64Mb, 128Mb 256Mb Output DQS valid window tQH tHPmin -tQHS Clock half period tHP tCLmin or tCHmin Data hold skew factor DQS write postamble time tQHS tWPST 0.75 0.25 0.75 0.25 0.8 0.25 4 ns tCK 3 Note : 1. Maximum burst refresh of 8 2. The specific requirement is that DQS be valid(High or Low) on or before this CK edge. The case shown(DQS going from High_Z to logic Low) applies when no writes were previously in progress on the bus. If a previous write was in progress, DQS could be High at this time, depending on tDQSS. 3. The maximum limit for this parameter is not a device limit. The device will operate with a great value for this parameter, but system performance (bus turnaround) will degrade accordingly. 4. A write command can be applied with tRCD satisfied after this command. 5. For registered DINNs, tCL and tCH are ≥ 45% of the period including both the half period jitter (tJIT(HP)) of the PLL and the half period jitter due to crosstalk (tJIT(crosstalk)) on the DIMM. Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 6. Input Setup/Hold Slew Rate Derating Input Setup/Hold Slew Rate ∆tIS ∆tIH (V/ns) (ps) (ps) 0.5 0 0 0.4 +50 +50 0.3 +100 +100 This derating table is used to increase tIS/tIH in the case where the input slew rate is below 0.5V/ns. Input setup/hold slew rate based on the lesser of AC-AC slew rate and DC-DC slew rate. 7. I/O Setup/Hold Slew Rate Derating I/O Setup/Hold Slew Rate ∆tDS ∆tDH (V/ns) (ps) (ps) 0.5 0 0 0.4 +75 +75 0.3 +150 +150 This derating table is used to increase tDS/tDH in the case where the I/O slew rate is below 0.5V/ns. I/O setup/hold slew rate based on the lesser of AC-AC slew rate and DC-DC slew rate. 8. I/O Setup/Hold Plateau Derating I/O Input Level ∆tDS ∆tDH (mV) (ps) (ps) ± 280 +50 +50 This derating table is used to increase tDS/tDH in the case where the input level is flat below VREF ± 310mV for a duration of up to 2ns. 9. I/O Delta Rise/Fall Rate(1/slew-rate) Derating Delta Rise/Fall Rate ∆tDS ∆tDH (ns/V) (ps) (ps) 0 0 0 ±0.25 +50 +50 ±0.5 +100 +100 This derating table is used to increase tDS/tDH in the case where the DQ and DQS slew rates differ. The Delta Rise/Fall Rate is calated as 1/SlewRate1-1/SlewRate2. For example, if slew rate 1 = 5V/ns and slew rate 2 =.4V/ns then the Delta Rise/Fall Rate =-0/5ns/V. Input S/H slew rate based on larger of AC-AC delta rise/fall rate and DC-DC delta rise/fall rate. 10. This parameter is fir system simulation purpose. It is guranteed by design. Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 Command Truth Table (V=Valid, X=Don′t Care, H=Logic High, L=Logic Low) COMMAND CKEn-1 CKEn CS RAS CAS WE BA0,1 A10/AP A11 A9 ~ A0 Note Register Extended MRS H X L L L L OP CODE 1, 2 Register Mode Register Set H X L L L L OP CODE 1, 2 L L L H X L H H H Auto Refresh Refresh Entry Self Refresh H L L H H X X X Bank Active & Row Addr. H X L L H H V Read & Column Address H X L H L H V Write & Column Address Exit H Auto Precharge Disable Auto Precharge Enable Auto Precharge Disable Auto Precharge Enable Burst Stop Precharge Bank Selection All Banks Active Power Down H X L H L L H X L H H L H X L L H L H X X X Entry H L Exit L H Entry H L Precharge Power Down Mode Exit L DM H No operation (NOP) : Not defined H H L V V V X X X X H X X X L H H H H X X X V V V L X X X X X L H H H 3 3 X V 3 Row Address L H L H Column Address (A0~A8) 4 Column Address (A0~A8) 4 X V L X H 4 4, 6 7 X 5 X X X H 3 X 8 9 9 Note : 1. OP Code : Operand Code. A0 ~ A11 & BA0 ~ BA1 : Program keys. (@EMRS/MRS) 2. EMRS/ MRS can be issued only at all banks precharge state. A new command can be issued 2 clock cycles after EMRS or MRS. 3. Auto refresh functions are same as the CBR refresh of DRAM. The automatical precharge without row precharge command is meant by "Auto". Auto/self refresh can be issued only at all banks precharge state. 4. BA0 ~ BA1 : Bank select addresses. If both BA0 and BA1 are "Low" at read, write, row active and precharge, bank A is selected. If both BA0 is "High" and BA1 is "Low" at read, write, row active and precharge, bank B is selected. If both BA0 is "Low" and BA1 is "High" at read, write, row active and precharge, bank C is selected. If both BA0 and BA1 are "High" at read, write, row active and precharge, bank D is selected. 5. If A10/AP is "High" at row precharge, BA0 and BA1 are ignored and all banks are selected. 6. During burst write with auto precharge, new read/write command can not be issued. Another bank read/write command can be issued after the end of burst. New row active of the associated bank can be issued at tRP after the end of burst. 7. Burst stop command is valid at every burst length. 8. DM sampled at the rising and falling edges of the DQS and Data-in are masked at the both edges (Write DM latency is 0). 9. This combination is not defined for any function, which means "No Operation(NOP)" in DDR SDRAM. Rev. 0.1 June. 2001 200pin DDR SDRAM SODIMM M470L1714BT0 PACKAGE DIMENSIONS Units : Inches (Millimeters) 2.70 (67.60) 2.50 (63.60) 1 39 41 0.456 11.40 0.086 2.15 199 2-φ 0.07 (1.80) 1.896 (47.40) 0.17 (4.20) 0.096 (2.40) 0.07 (1.8) 0.79 (20.00) 0.24 (6.0) 0.16 ± 0.039 (4.00 ± 0.10) 1.25 (31.75) Full R 2x Z Y 0.098 2.45 200 0.157 Min (4.00 Min) 0.157 Min (4.00 Min) 0.150 Max (3.80 Max) 0.04 ± 0.0039 (1.00 ± 0.10) 0.16 ± 0.0039 (4.00 ± 0.10) 0.04 ± 0.0039 (1.00 ± 0.1) Detail Z 0.102 Min 40 42 (2.55 Min) 2 0.018 ± 0.001 (0.45 ± 0.03) 0.01 (0.25) 0.024 TYP (0.60 TYP) Detail Y Tolerances : ±.006(.15) unless otherwise specified The used device is 8Mx16 SDRAM, TSOP SDRAM Part No. : K4H281638B-TC/L Rev. 0.1 June. 2001