AD ADF4107BRU Pll frequency synthesizer Datasheet

PLL Frequency Synthesizer
ADF4107
Data Sheet
FEATURES
GENERAL DESCRIPTION
7.0 GHz bandwidth
2.7 V to 3.3 V power supply
Separate charge pump supply (VP) allows extended tuning
voltage in 3 V systems
Programmable dual-modulus prescaler
8/9, 16/17, 32/33, 64/65
Programmable charge pump currents
Programmable antibacklash pulse width
3-wire serial interface
Analog and digital lock detect
Hardware and software power-down mode
The ADF4107 frequency synthesizer can be used to implement
local oscillators in the upconversion and downconversion sections
of wireless receivers and transmitters. It consists of a low noise
digital PFD (phase frequency detector), a precision charge pump, a
programmable reference divider, programmable A and B counters,
and a dual-modulus prescaler (P/P + 1). The A (6-bit) and B
(13-bit) counters, in conjunction with the dual-modulus
prescaler (P/P + 1), implement an N divider (N = BP + A). In
addition, the 14-bit reference counter (R counter), allows
selectable REFIN frequencies at the PFD input. A complete PLL
(phase-locked loop) can be implemented if the synthesizer is
used with an external loop filter and VCO (voltage controlled
oscillator). Its very high bandwidth means that frequency
doublers can be eliminated in many high frequency systems,
simplifying system architecture and reducing cost.
APPLICATIONS
Broadband wireless access
Satellite systems
Instrumentation
Wireless LANs
Base stations for wireless radio
FUNCTIONAL BLOCK DIAGRAM
AVDD
DVDD
VP
RSET
CPGND
REFERENCE
14-BIT
R COUNTER
REFIN
PHASE
FREQUENCY
DETECTOR
CHARGE
PUMP
CP
14
R COUNTER
LATCH
CLK
DATA
LE
24-BIT INPUT
REGISTER
SDOUT
FUNCTION
LATCH
22
FROM
FUNCTION
LATCH
A, B COUNTER
LATCH
CURRENT
SETTING 1
CURRENT
SETTING 2
CPI3 CPI2 CPI1
CPI6 CPI5 CPI4
HIGH Z
19
AVDD
MUXOUT
MUX
13
N = BP + A
RFINA
RFINB
LOCK
DETECT
13-BIT
B COUNTER
SDOUT
LOAD
PRESCALER
P/P + 1
LOAD
M3 M2 M1
6-BIT
A COUNTER
03338-001
ADF4107
6
CE
AGND
DGND
Figure 1.
Rev. D
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2003–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADF4107
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Phase Frequency Detector and Charge Pump ..............................9
Applications ....................................................................................... 1
MUXOUT and Lock Detect...................................................... 10
General Description ......................................................................... 1
Input Shift Register .................................................................... 10
Functional Block Diagram .............................................................. 1
Latch Summary........................................................................... 11
Revision History ............................................................................... 2
Reference Counter Latch Map .................................................. 12
Specifications..................................................................................... 3
AB Counter Latch Map ............................................................. 13
Timing Characteristics ................................................................ 4
Function Latch Map ................................................................... 14
Absolute Maximum Ratings ............................................................ 5
Initialization Latch Map ............................................................ 15
ESD Caution .................................................................................. 5
Function Latch ............................................................................ 16
Pin Configurations and Function Descriptions ........................... 6
Initialization Latch ..................................................................... 17
Typical Performance Characteristics ............................................. 7
Device Programming after Initial Power-Up ............................. 17
Functional Description .................................................................... 9
Applications..................................................................................... 18
Reference Input Stage................................................................... 9
Local Oscillator for LMDS Base Station Transmitter ............ 18
RF Input Stage ............................................................................... 9
Interfacing ................................................................................... 19
Prescaler (P/P + 1) ........................................................................ 9
PCB Design Guidelines for Chip Scale Package .................... 19
A and B Counters ......................................................................... 9
Outline Dimensions ....................................................................... 20
R Counter ...................................................................................... 9
Ordering Guide .......................................................................... 20
REVISION HISTORY
3/13—Rev. C to Rev. D
Changed RFINA to RFINB Parameter from ±320 mV to ±600 mV,
Table 3 ................................................................................................ 5
Updated Outline Dimensions ....................................................... 20
Changes to Ordering Guide .......................................................... 20
11/12—Rev. B to Rev. C
Changed EVAL-ADF411xEBZ1 to EV-ADF411XSD1Z ............. 4
Changes to Table 3 ............................................................................ 5
Updated Outline Dimensions ....................................................... 20
Changes to Ordering Guide .......................................................... 20
4/07—Rev. 0 to Rev. A
Updated Format .................................................................. Universal
Changes to REFIN Characteristics Section ...................................3
Changes to Noise Characteristics Section ......................................4
Changes to Absolute Maximum Ratings Section ..........................5
Changes to Figure 23...................................................................... 12
Changes to Ordering Guide .......................................................... 20
5/03—Revision 0: Initial Version
9/11—Rev. A to Rev. B
Changes to Normalized Phase Noise Floor (PNSYNTH) Parameter,
Table 1 ................................................................................................ 3
Added Normalized 1/f Noise (PN1_f) Parameter and Endnote 11,
Table 1 ................................................................................................ 3
Changed EVAL-ADF4107EB1 to EVAL-ADF411xEBZ1 ............ 4
Changes to Figure 4 and Table 4 ..................................................... 6
Updated Outline Dimensions ....................................................... 20
Changes to Ordering Guide .......................................................... 20
Rev. D | Page 2 of 20
Data Sheet
ADF4107
SPECIFICATIONS
AVDD = DVDD = 3 V ± 10%, AVDD ≤ VP ≤ 5.5 V, AGND = DGND = CPGND = 0 V, RSET = 5.1 kΩ, dBm referred to 50 Ω, TA = TMAX to TMIN,
unless otherwise noted.
Table 1.
Parameter
RF CHARACTERISTICS
RF Input Frequency (RFIN) 3
RF Input Sensitivity
Maximum Allowable Prescaler Output
Frequency 4
REFIN CHARACTERISTICS
REFIN Input Frequency
REFIN Input Sensitivity 5
REFIN Input Capacitance
REFIN Input Current
PHASE DETECTOR
Phase Detector Frequency 7
CHARGE PUMP
ICP Sink/Source
High Value
Low Value
Absolute Accuracy
RSET Range
ICP Three-State Leakage
Sink and Source Current Matching
ICP vs. VCP
ICP vs. Temperature
LOGIC INPUTS
VIH, Input High Voltage
VIL, Input Low Voltage
IINH, IINL, Input Current
CIN, Input Capacitance
LOGIC OUTPUTS
VOH, Output High Voltage
VOH, Output High Voltage
IOH
VOL, Output Low Voltage
POWER SUPPLIES
AVDD
DVDD
VP
IDD 8 (AIDD + DIDD)
IP
Power-Down Mode 9 (AIDD + DIDD)
NOISE CHARACTERISTICS
Normalized Phase Noise Floor (PNSYNTH) 10
Normalized 1/f Noise (PN1_f) 11
B Version 1
B Chips 2 (Typ)
Unit
Test Conditions/Comments
1.0/7.0
–5/+5
300
1.0/7.0
–5/+5
300
GHz min/max
dBm min/max
MHz max
See Figure 18 for input circuit
20/250
0.8/VDD
10
±100
20/250
0.8/VDD
10
±100
MHz min/max
V p-p min/max
pF max
µA max
For f < 20 MHz, ensure slew rate >50 V/µs
Biased at AVDD/2 6
104
104
MHz max
ABP = 0,0 (2.9 ns antibacklash pulse width)
Programmable; see Figure 25
5
625
2.5
3.0 to 11
1
2
1.5
2
5
625
2.5
3.0 to 11
1
2
1.5
2
mA typ
µA typ
% typ
kΩ typ
nA typ
% typ
% typ
% typ
With RSET = 5.1 kΩ
1.4
0.6
±1
10
1.4
0.6
±1
10
V min
V max
µA max
pF max
1.4
1.4
V min
VDD − 0.4
100
0.4
VDD − 0.4
100
0.4
V min
µA max
V max
2.7/3.3
AVDD
AVDD/5.5
17
0.4
10
2.7/3.3
AVDD
AVDD/5.5
15
0.4
10
V min/V max
V min/V max
mA max
mA max
µA typ
AVDD ≤ VP ≤ 5.5 V
15 mA typ
TA = 25°C
−223
−223
dBc/Hz typ
−122
−122
dBc/Hz typ
PLL loop BW = 500 kHz, measured at
100 kHz offset
10 kHz offset; normalized to 1 GHz
Rev. D | Page 3 of 20
With RSET = 5.1 kΩ
See Figure 25
0.5 V ≤ VCP ≤ VP − 0.5 V
0.5 V ≤ VCP ≤ VP − 0.5 V
VCP = VP/2
Open-drain output chosen; 1 kΩ pull-up
resistor to 1.8 V
CMOS output chosen
IOL = 500 µA
ADF4107
Data Sheet
B Version1
B Chips2 (Typ)
Unit
−93
−76
−83
−93
−76
−83
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
−90/−92
−90/−92
dBc typ
6400 MHz Output14
−65/−70
−65/−70
dBc typ
6400 MHz Output15
−70/−75
−70/−75
dBc typ
Parameter
Phase Noise Performance12
900 MHz Output13
6400 MHz Output14
6400 MHz Output15
Spurious Signals
900 MHz Output13
Test Conditions/Comments
@ VCO output
@ 1 kHz offset and 200 kHz PFD frequency
@ 1 kHz offset and 200 kHz PFD frequency
@ 1 kHz offset and 1 MHz PFD frequency
@ 200 kHz/400 kHz and 200 kHz PFD
frequency
@ 200 kHz/400 kHz and 200 kHz PFD
frequency
@ 1 MHz/2 MHz and 1 MHz PFD frequency
1
Operating temperature range (B version) is −40°C to +85°C.
The B chip specifications are given as typical values.
3
Use a square wave for lower frequencies, below the minimum stated.
4
This is the maximum operating frequency of the CMOS counters. The prescaler value should be chosen to ensure that the RF input is divided down to a frequency that
is less than this value.
5
AVDD = DVDD = 3 V.
6
AC-coupling ensures AVDD/2 bias.
7
Guaranteed by design. Sample tested to ensure compliance.
8
TA = 25°C; AVDD = DVDD = 3 V; P = 32; RFIN = 7.0 GHz.
9
TA = 25°C; AVDD = DVDD = 3.3 V; R = 16,383; A = 63; B = 891; P = 32; RFIN = 7.0 GHz.
10
The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20logN (where N is the N divider value)
and 10 log(FPFD). PNSYNTH = PNTOT – 20 logN −10 logFPFD.
11
The PLL phase noise is composed of 1/f (flicker) noise plus the normalized PLL noise floor. The formula for calculating the 1/f noise contribution at an RF frequency, fRF,
and at a frequency offset, f, is given by PN = PN1_f + 10 log(10 kHz/f) + 20 log(fRF/1 GHz). Both the normalized phase noise floor and flicker noise are modeled in
ADIsimPLL.
12
The phase noise is measured with the EV-ADF411xSD1Z evaluation board and the HP8562E spectrum analyzer. The spectrum analyzer provides the REFIN for the
synthesizer (fREFOUT = 10 MHz @ 0 dBm).
13
fREFIN = 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 900 MHz; N = 4500; loop BW = 20 kHz.
14
fREFIN = 10 MHz; fPFD = 200 kHz; offset frequency = 1 kHz; fRF = 6400 MHz; N = 32,000; loop BW = 20 kHz.
15
fREFIN = 10 MHz; fPFD = 1 MHz; offset frequency = 1 kHz; fRF = 6400 MHz; N = 6400; loop BW = 100 kHz.
2
TIMING CHARACTERISTICS
AVDD = DVDD = 3 V ± 10%, AVDD ≤ VP ≤ 5.5 V, AGND = DGND = CPGND = 0 V, RSET = 5.1 kΩ, dBm referred to 50 Ω, TA = TMAX to TMIN,
unless otherwise noted. 1
Table 2.
Limit2 (B Version)
10
10
25
25
10
20
Parameter
t1
t2
t3
t4
t5
t6
2
Test Conditions/Comments
DATA to CLOCK setup time
DATA to CLOCK hold time
CLOCK high duration
CLOCK low duration
CLOCK to LE setup time
LE pulse width
Guaranteed by design but not production tested.
Operating temperature range (B Version) is −40°C to +85°C.
t3
t4
CLOCK
t1
DATA
DB23 (MSB)
t2
DB22
DB2
DB1 (CONTROL
BIT C2)
DB0 (LSB)
(CONTROL BIT C1)
t6
LE
t5
03338-002
1
Unit
ns min
ns min
ns min
ns min
ns min
ns min
LE
Figure 2. Timing Diagram
Rev. D | Page 4 of 20
Data Sheet
ADF4107
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3.
Parameter
AVDD to GND 1
AVDD to DVDD
VP to GND
VP to AVDD
Digital I/O Voltage to GND
Analog I/O Voltage to GND
REFIN, RFINA, RFINB to GND
RFINA to RFINB
Operating Temperature Range
Industrial (B Version)
Storage Temperature Range
Maximum Junction Temperature
TSSOP θJA Thermal Impedance
LFCSP θJA Thermal Impedance
(Paddle Soldered)
Reflow Soldering
Peak Temperature
Time at Peak Temperature
Transistor Count
CMOS
Bipolar
1
Rating
−0.3 V to +3.6 V
−0.3 V to +0.3 V
−0.3 V to +5.8 V
−0.3 V to +5.8 V
−0.3 V to VDD + 0.3 V
−0.3 V to Vp + 0.3 V
−0.3 V to VDD + 0.3 V
±600 mV
−40°C to +85°C
−65°C to +125°C
150°C
112°C/W
30.4°C/W
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
This device is a high performance RF integrated circuit with an
ESD rating of <2 kV, and it is ESD sensitive. Proper precautions
should be taken for handling and assembly.
ESD CAUTION
260°C
40 sec
6425
303
GND = AGND = DGND = 0 V.
Rev. D | Page 5 of 20
ADF4107
Data Sheet
20
19
18
17
16
CP
RSET
VP
DVDD
DVDD
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
VP
16
CP 2
15
DVDD
CPGND 3
14
MUXOUT
ADF4107
CPGND
AGND
AGND
RFINB
RFINA
TOP VIEW 13 LE
(Not to Scale)
12 DATA
RFINB 5
11
CLK
AVDD 7
10
CE
REFIN 8
9
DGND
NOTES:
1. TRANSISTOR COUNT 6425 (CMOS),
303 (BIPOLAR).
TOP VIEW
(Not to Scale)
15
14
13
12
11
MUXOUT
LE
DATA
CLK
CE
NOTES
1. TRANSISTOR COUNT 6425 (CMOS),
303 (BIPOLAR).
2. THE EXPOSED PAD MUST BE
CONNECTED TO AGND.
03338-003
RFINA 6
ADF4107
AVDD 6
AVDD 7
REFIN 8
DGND 9
DGND 10
AGND 4
1
2
3
4
5
Figure 3. Pin Configuration, TSSOP
03338-004
RSET 1
Figure 4. Pin Configuration, LFCSP
Table 4. Pin Function Descriptions
Pin No.
TSSOP LFCSP
1
19
Mnemonic
RSET
2
20
CP
3
4
5
1
2, 3
4
CPGND
AGND
RFINB
6
7
5
6, 7
RFINA
AVDD
8
8
REFIN
9
10
9, 10
11
DGND
CE
11
12
CLK
12
13
DATA
13
14
LE
14
15
MUXOUT
15
16, 17
DVDD
16
18
VP
EP
Description
Connecting a resistor between this pin and CPGND sets the maximum charge pump output current. The
nominal voltage potential at the RSET pin is 0.66 V. The relationship between ICP and RSET is
25.5
I CP MAX =
R SET
so, with RSET = 5.1 kΩ, ICP MAX = 5 mA.
Charge Pump Output. When enabled, this pin provides ±ICP to the external loop filter, which in turn drives
the external VCO.
Charge Pump Ground. This is the ground return path for the charge pump.
Analog Ground. This is the ground return path of the prescaler.
Complementary Input to the RF Prescaler. This point must be decoupled to the ground plane with a small
bypass capacitor, typically 100 pF. See Figure 18.
Input to the RF Prescaler. This small signal input is ac-coupled to the external VCO.
Analog Power Supply. This voltage may range from 2.7 V to 3.3 V. Decoupling capacitors to the analog
ground plane should be placed as close as possible to this pin. AVDD must be the same value as DVDD.
Reference Input. This is a CMOS input with a nominal threshold of VDD/2 and a dc equivalent input
resistance of 100 kΩ. See Figure 17. This input can be driven from a TTL or CMOS crystal oscillator or it can
be ac-coupled.
Digital Ground.
Chip Enable. A logic low on this pin powers down the device and puts the charge pump output into threestate mode. Taking the pin high powers up the device, depending on the status of the power-down bit, F2.
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched
into the 24-bit shift register on the CLK rising edge. This input is a high impedance CMOS input.
Serial Data Input. The serial data is loaded MSB first with the two LSBs being the control bits. This input is a
high impedance CMOS input.
Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into one of
the four latches, the latch being selected using the control bits.
This multiplexer output allows either the lock detect, the scaled RF, or the scaled reference frequency to
be accessed externally.
Digital Power Supply. This may range from 2.7 V to 3.3 V. Decoupling capacitors to the digital ground
plane should be placed as close as possible to this pin. DVDD must be the same value as AVDD.
Charge Pump Power Supply. This voltage should be greater than or equal to VDD. In systems where VDD is 3 V, it
can be set to 5 V and used to drive a VCO with a tuning range of up to 5 V.
Exposed Pad. The exposed pad must be connected to AGND.
Rev. D | Page 6 of 20
Data Sheet
ADF4107
TYPICAL PERFORMANCE CHARACTERISTICS
–40
10dB/DIV
RL = –40dBc/Hz
RMS NOISE = 0.36°
–50
PHASE NOISE (dBc/Hz)
–60
–70
–80
–90
–100
–110
03338-008
–120
03338-005
–130
–140
100Hz
Figure 5. Parameter Data for the RF Input
Figure 8. Integrated Phase Noise (900 MHz, 200 kHz, 20 kHz)
0
0
VDD = 3V
VP = 3V
REF LEVEL = –14.0dBm
–10
–5
OUTPUT POWER (dB)
–20
–10
–15
–20
TA = +85°C
–30
–40
–50
–60
–70
–91.0dBc/Hz
TA = –40°C
0
1
2
3
4
5
03338-009
TA = +25°C
–30
–90
–100
6
–400kHz
–200kHz
RF INPUT FREQUENCY (GHz)
900MHz
200kHz
400kHz
FREQUENCY
Figure 6. Input Sensitivity
Figure 9. Reference Spurs (900 MHz, 200 kHz, 20 kHz)
0
0
–20
–30
–40
REF LEVEL = –10dBm
VDD = 3V, VP = 5V
ICP = 5mA
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 SECONDS
AVERAGES = 10
–10
–20
OUTPUT POWER (dB)
REF LEVEL = –14.3dBm
–10
–50
–60
–93.0dBc/Hz
–70
–80
–30
–40
–50
–60
–70
03338-007
–80
–90
–100
–2kHz
–1kHz
900MHz
1kHz
VDD = 3V, VP = 5V
ICP = 5mA
PFD FREQUENCY = 1MHz
LOOP BANDWIDTH = 100kHz
RES BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
SWEEP = 1.9 SECONDS
AVERAGES = 10
–83.5dBc/Hz
03338-010
OUTPUT POWER (dB)
VDD = 3V, VP = 5V
ICP = 5mA
PFD FREQUENCY = 200kHz
LOOP BANDWIDTH = 20kHz
RES BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
SWEEP = 2.5 SECONDS
AVERAGES = 30
–80
–25
03338-006
RF INPUT POWER (dBm)
1MHz
FREQUENCY OFFSET FROM 900MHz CARRIER
–90
–100
2kHz
–2kHz
FREQUENCY
–1kHz
6400MHz
1kHz
2kHz
FREQUENCY
Figure 7. Phase Noise (900 MHz, 200 kHz, 20 kHz)
Figure 10. Phase Noise (6.4 GHz, 1 MHz, 100 kHz)
Rev. D | Page 7 of 20
ADF4107
Data Sheet
–40
–5
10dB/DIV
RL = –40dBc/Hz
RMS NOISE = 1.8°
–70
–80
–90
–100
–110
03338-011
–120
–130
–25
–35
–45
–55
–65
–75
–85
03338-014
PHASE NOISE (dBc/Hz)
–60
–140
100Hz
VDD = 3V
VP = 5V
–15
FIRST REFERENCE SPUR (dBc)
–50
–95
–105
0
1MHz
1
2
5
–120
0
VDD = 3V, VP = 5V
ICP = 5mA
PFD FREQUENCY = 1MHz
LOOP BANDWIDTH = 100kHz
RES BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
SWEEP = 13 SECONDS
AVERAGES = 1
–20
–30
–40
VDD = 3V
VP = 5V
–130
PHASE NOISE (dBc/Hz)
REF LEVEL = –10dBm
–10
–50
–65.0dBc
–66.0dBc
–60
–70
–80
–140
–150
–160
03338-012
–170
–90
–100
–2kHz
–1kHz
5800MHz
1kHz
03338-015
OUTPUT POWER (dB)
4
Figure 14. Reference Spurs vs. VTUNE (6.4 GHz, 1 MHz, 100 kHz)
Figure 11. Integrated Phase Noise (6.4 GHz, 1 MHz, 100 kHz)
–180
10k
2kHz
100k
1M
10M
100M
PHASE DETECTOR FREQUENCY (Hz)
FREQUENCY (MHz)
Figure 12. Reference Spurs (6.4 GHz, 1 MHz, 100 kHz)
Figure 15. Phase Noise (Referred to CP Output) vs. PFD Frequency
–6
–60
VDD = 3V
VP = 3V
–5
–4
VP = 5V
ICP SETTLING = 5mA
–3
–70
–2
ICP (mA)
PHASE NOISE (dBc/Hz)
3
TUNING VOLTAGE (V)
FREQUENCY OFFSET FROM 5800MHz CARRIER
–80
–1
0
1
2
3
–90
–20
0
20
40
60
80
03338-016
–100
–40
03338-013
4
5
6
0
100
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
VCP (V)
TEMPERATURE (°C)
Figure 13. Phase Noise (6.4 GHz, 1 MHz, 100 kHz) vs. Temperature
Figure 16. Charge Pump Output Characteristics
Rev. D | Page 8 of 20
5.0
Data Sheet
ADF4107
FUNCTIONAL DESCRIPTION
REFERENCE INPUT STAGE
A AND B COUNTERS
The reference input stage is shown in Figure 17. SW1 and SW2
are normally closed switches. SW3 is normally open. When
power-down is initiated, SW3 is closed and SW1 and SW2 are
opened. This ensures that there is no loading of the REFIN pin
on power-down.
The A and B CMOS counters combine with the dual-modulus
prescaler to allow a wide ranging division ratio in the PLL
feedback counter. The counters are specified to work when the
prescaler output is 300 MHz or less. Thus, with an RF input
frequency of 4.0 GHz, a prescaler value of 16/17 is valid but a
value of 8/9 is not valid.
POWER-DOWN
CONTROL
Pulse Swallow Function
100kΩ
SW2
REFIN
TO R COUNTER
NC
BUFFER
NO
SW3
fVCO is the output frequency of external voltage controlled
oscillator (VCO).
P is the preset modulus of dual-modulus prescaler (8/9, 16/17).
B is the preset divide ratio of binary 13-bit counter (3 to 8191).
A is the preset divide ratio of binary 6-bit swallow counter (0 to 63).
fREFIN is the external reference frequency oscillator.
RF INPUT STAGE
The RF input stage is shown in Figure 18. It is followed by a
2-stage limiting amplifier to generate the CML clock levels
needed for the prescaler.
500Ω
f REFIN
R
where:
Figure 17. Reference Input Stage
BIAS
GENERATOR
f VCO  P  B   A 
03338-017
SW1
The A and B counters, in conjunction with the dual-modulus
prescaler, make it possible to generate output frequencies that
are spaced only by the reference frequency divided by R. The
equation for the VCO frequency is as follows:
N = BP + A
1.6V
AVDD
13-BIT B
COUNTER
500Ω
FROM RF
INPUT STAGE
PRESCALER
P/P + 1
RFINA
MODULUS
CONTROL
LOAD
LOAD
6-BIT A
COUNTER
RFINB
N DIVIDER
Figure 19. A and B Counters
03338-018
AGND
TO PFD
03338-019
NC
R COUNTER
Figure 18. RF Input Stage
PRESCALER (P/P + 1)
The dual-modulus prescaler (P/P + 1), along with the A and B
counters, enables the large division ratio, N, to be realized
(N = BP + A). The dual-modulus prescaler, operating at CML
levels, takes the clock from the RF input stage and divides it
down to a manageable frequency for the CMOS A and CMOS B
counters. The prescaler is programmable. It can be set in
software to 8/9, 16/17, 32/33, or 64/65. It is based on a
synchronous 4/5 core. A minimum divide ratio is possible for
fully contiguous output frequencies. This minimum is
determined by P, the prescaler value, and is given by: (P2 − P).
The 14-bit R counter allows the input reference frequency to be
divided down to produce the reference clock to the phase
frequency detector (PFD). Division ratios from 1 to 16,383 are
allowed.
PHASE FREQUENCY DETECTOR AND CHARGE PUMP
The phase frequency detector (PFD) takes inputs from the R
counter and N counter (N = BP + A) and produces an output
proportional to the phase and frequency difference between
them. Figure 20 is a simplified schematic. The PFD includes a
programmable delay element that controls the width of the
antibacklash pulse. This pulse ensures that there is no dead zone
in the PFD transfer function and minimizes phase noise and
reference spurs. Two bits in the reference counter latch, ABP2
and ABP1, control the width of the pulse. Use of the minimum
antibacklash pulse width is not recommended. See Figure 23.
Rev. D | Page 9 of 20
ADF4107
Data Sheet
DVDD
VP
CHARGE
PUMP
HI
D1
Q1
UP
ANALOG LOCK DETECT
U1
R DIVIDER
DIGITAL LOCK DETECT
CLR1
R COUNTER OUTPUT
MUX
CONTROL
MUXOUT
PROGRAMMABLE
DELAY
N COUNTER OUTPUT
U3
CP
SDOUT
HI
ABP1
DGND
CLR2 DOWN
D2 Q2
03338-021
ABP2
Figure 21. MUXOUT Circuit
03338-020
U2
N DIVIDER
CPGND
Figure 20. PFD Simplified Schematic and Timing (in Lock)
MUXOUT AND LOCK DETECT
The output multiplexer on the ADF4107 allows the user to
access various internal points on the chip. The state of
MUXOUT is controlled by M3, M2, and M1 in the function
latch. Figure 25 shows the full truth table. Figure 21 shows the
MUXOUT section in block diagram form.
Lock Detect
MUXOUT can be programmed for two types of lock detect:
digital lock detect and analog lock detect.
Digital lock detect is active high. When the lock detect
precision (LDP) bit in the R counter latch is set to 0, digital lock
detect is set high when the phase error on three consecutive
phase detector (PD) cycles is less than 15 ns. With LDP set to 1,
five consecutive cycles of less than 15 ns are required to set the
lock detect. It stays set high until a phase error of greater than
25 ns is detected on any subsequent PD cycle.
INPUT SHIFT REGISTER
The ADF4107 digital section includes a 24-bit input shift
register, a 14-bit R counter, and a 19-bit N counter, comprising a
6-bit A counter and a 13-bit B counter. Data is clocked into the
24-bit shift register on each rising edge of CLK. The data is
clocked in MSB first. Data is transferred from the shift register
to one of four latches on the rising edge of LE. The destination
latch is determined by the state of the two control bits (C2, C1)
in the shift register. These are the two LSBs, DB1 and DB0, as
shown in the timing diagram of Figure 2. The truth table for
these bits is shown in Table 5. Figure 22 shows a summary of
how the latches are programmed.
Table 5. C2, C1 Truth Table
Control Bits
C2
C1
0
0
0
1
1
0
1
1
The N-channel open-drain analog lock detect should be
operated with an external pull-up resistor of 10 kΩ nominal.
When lock has been detected, this output becomes high with
narrow, low going pulses.
Rev. D | Page 10 of 20
Data Latch
R Counter
N Counter (A and B)
Function Latch (Including Prescaler)
Initialization Latch
Data Sheet
ADF4107
LATCH SUMMARY
LOCK
DETECT
PRECISION
REFERENCE COUNTER LATCH
RESERVED
TEST
MODE BITS
ANTIBACKLASH
WIDTH
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
X
0
0
LDP
T2
T1
CONTROL
BITS
14-BIT REFERENCE COUNTER
ABP2 ABP1
R14
R13
R12
R11
R10
R9
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
R8
R7
R6
R5
R4
R3
R2
R1
C2 (0)
C1 (0)
RESERVED
CP GAIN
N COUNTER LATCH
13-BIT B COUNTER
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
X
X
G1
B13
B12
B11
B10
B9
B8
B7
B6
CONTROL
BITS
6-BIT A COUNTER
B5
B4
B3
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
B2
B1
A6
A5
A4
A3
A2
A1
C2 (0) C1 (1)
CONTROL
BITS
DB1
DB0
FASTLOCK
ENABLE
CP THREESTATE
PD
POLARITY
POWERDOWN 1
COUNTER
RESET
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
F4
F3
F2
M3
M2
M1
PD1
F1
C2 (1) C1 (0)
MUXOUT
CONTROL
PRESCALER
VALUE
P2
P1
POWERDOWN 2
FASTLOCK
MODE
FUNCTION LATCH
PD2
CURRENT
SETTING
2
CPI6
CPI5
CPI4
CURRENT
SETTING
1
CPI3
CPI2
CPI1
TIMER COUNTER
CONTROL
TC4
TC3
TC2
TC1
F5
MUXOUT
CONTROL
DB1
DB0
FASTLOCK
ENABLE
CP THREESTATE
PD
POLARITY
POWERDOWN 1
COUNTER
RESET
CONTROL
BITS
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
F4
F3
F2
M3
M2
M1
PD1
F1
P2
P1
PD2
CURRENT
SETTING
2
CPI6
CPI5
CPI4
CURRENT
SETTING
1
CPI3
CPI2
TIMER COUNTER
CONTROL
CPI1
TC4
TC3
TC2
TC1
F5
Figure 22. Latch Summary
Rev. D | Page 11 of 20
DB0
C2 (1) C1 (1)
03338-022
PRESCALER
VALUE
POWERDOWN 2
FASTLOCK
MODE
INITIALIZATION LATCH
ADF4107
Data Sheet
LOCK
DETECT
PRECISION
REFERENCE COUNTER LATCH MAP
RESERVED
TEST
MODE BITS
ANTIBACKLASH
WIDTH
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
X
0
LDP
0
T2
T1
ABP2 ABP1
CONTROL
BITS
14-BIT REFERENCE COUNTER
R14
R12
R13
R11
R10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
R8
R7
R6
R5
R4
R3
R2
R1
C2 (0)
C1 (0)
R9
X = DON’T CARE
ABP2
0
0
1
1
ABP1
0
1
0
1
R14
R13
R12
..........
R3
R2
R1
DIVIDE RATIO
0
0
0
0
.
.
.
0
0
0
0
.
.
.
0
0
0
0
.
.
.
..........
..........
..........
..........
..........
..........
..........
0
0
0
1
.
.
.
0
1
1
0
.
.
.
1
0
1
0
.
.
.
1
2
3
4
.
.
.
1
1
1
..........
1
0
0
16380
1
1
1
..........
1
0
1
16381
1
1
1
..........
1
1
0
16382
1
1
1
..........
1
1
1
16383
ANTIBACKLASH PULSE WIDTH
2.9ns
1.3ns TEST MODE ONLY. DO NOT USE
6.0ns
2.9ns
TEST MODE BITS
SHOULD BE SET
TO 00 FOR NORMAL
OPERATION.
LDP
0
1
OPERATION
THREE CONSECUTIVE CYCLES OF PHASE DELAY LESS THAN
15ns MUST OCCUR BEFORE LOCK DETECT IS SET.
FIVE CONSECUTIVE CYCLES OF PHASE DELAY LESS THAN
15ns MUST OCCUR BEFORE LOCK DETECT IS SET.
03338-023
BOTH OF THESE BITS
MUST BE SET TO 0 FOR
NORMAL OPERATION.
Figure 23. Reference Counter Latch Map
Rev. D | Page 12 of 20
Data Sheet
ADF4107
CP GAIN
AB COUNTER LATCH MAP
RESERVED
CONTROL
BITS
6-BIT A COUNTER
13-BIT B COUNTER
DB23
DB22
DB21
DB20
DB19
DB18
DB17
DB16
DB15
DB14
DB13
DB12
DB11
DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
X
X
G1
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
A6
A5
A4
A3
A2
A1
DB1
DB0
C2 (0) C1 (1)
X = DON’T CARE
B13
B12
B11
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
A6
A5
..........
A2
A1
A COUNTER
DIVIDE RATIO
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
0
0
1
1
.
.
.
0
0
1
1
0
1
0
1
.
.
.
0
1
0
1
0
1
2
3
.
.
.
60
61
62
63
B3
B2
B1
B COUNTER DIVIDE RATIO
0
0
0
0
.
.
.
1
1
1
1
0
0
1
1
.
.
.
0
0
1
1
0
1
0
1
.
.
.
0
1
0
1
NOT ALLOWED
NOT ALLOWED
NOT ALLOWED
3
.
.
.
8188
8189
8190
8191
F4 (FUNCTION LATCH)
FASTLOCK ENABLE
CP GAIN
OPERATION
0
0
CHARGE PUMP CURRENT
SETTING 1 IS PERMANENTLY USED.
0
1
1
0
1
1
CHARGE PUMP CURRENT
SETTING 2 IS PERMANENTLY USED.
CHARGE PUMP CURRENT
SETTING 1 IS USED.
CHARGE PUMP CURRENT IS
SWITCHED TO SETTING 2. THE
TIME SPENT IN SETTING 2 IS
DEPENDENT ON WHICH FASTLOCK
MODE IS USED. SEE FUNCTION
LATCH DESCRIPTION.
N = BP + A, P IS PRESCALER VALUE SET IN THE FUNCTION
LATCH. B MUST BE GREATER THAN OR EQUAL TO A. FOR
CONTINUOUSLY ADJACENT VALUES OF (N × FREF ), AT THE
OUTPUT, NMIN IS (P2 – P).
03338-024
THESE BITS ARE NOT USED
BY THE DEVICE AND ARE
DON'T CARE BITS.
Figure 24. AB Counter Latch Map
Rev. D | Page 13 of 20
ADF4107
Data Sheet
FASTLOCK
ENABLE
CP THREESTATE
PD
POLARITY
POWERDOWN 1
COUNTER
RESET
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
F4
F3
F2
M3
M2
M1
PD1
F1
POWERDOWN 2
FASTLOCK
MODE
FUNCTION LATCH MAP
PRESCALER
VALUE
P1
PD2
CPI6
CPI5
CPI4
CPI2
CPI3
TIMER COUNTER
CONTROL
CPI1
TC4
TC3
TC2
TC1
TC4
TC3
TC2
TC1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
3kΩ
1.06
2.12
3.18
4.24
5.30
6.36
7.42
8.50
5.1kΩ
0.625
1.25
1.875
2.5
3.125
3.75
4.375
5.0
CPI6
CPI5
CPI4
CPI3
0
0
0
0
1
1
1
1
CPI2
0
0
1
1
0
0
1
1
CPI1
0
1
0
1
0
1
0
1
PD2
PD1
MODE
X
X
0
1
X
0
1
1
ASYNCHRONOUS POWER-DOWN
NORMAL OPERATION
ASYNCHRONOUS POWER-DOWN
SYNCHRONOUS POWER-DOWN
P1
PRESCALER VALUE
0
1
0
1
8/9
16/17
32/33
64/65
PHASE DETECTOR
POLARITY
F1
0
1
NEGATIVE
POSITIVE
0
1
F3
CHARGE PUMP
OUTPUT
0
1
NORMAL
THREE-STATE
F4
F5
FASTLOCK MODE
0
1
1
X
0
1
FASTLOCK DISABLED
FASTLOCK MODE 1
FASTLOCK MODE 2
TIMEOUT
(PFD CYCLES)
3
7
11
15
19
23
27
31
35
39
43
47
51
55
59
63
DB1
DB0
C2 (1) C1 (0)
COUNTER
OPERATION
NORMAL
R, A, B COUNTERS
HELD IN RESET
M3
M2
M1
OUTPUT
0
0
0
0
0
1
0
0
1
1
1
1
0
0
0
1
0
1
1
1
1
1
0
1
THREE-STATE OUTPUT
DIGITAL LOCK DETECT
(ACTIVE HIGH)
N DIVIDER OUTPUT
DVDD
R DIVIDER OUTPUT
N-CHANNEL OPEN-DRAIN
LOCK DETECT
SERIAL DATA OUTPUT
DGND
11kΩ
0.289
0.580
0.870
1.160
1.450
1.730
2.020
2.320
CE PIN
0
0
1
1
F2
CONTROL
BITS
ICP (mA)
0
1
1
1
P2
F5
MUXOUT
CONTROL
03338-025
P2
CURRENT
SETTING
1
CURRENT
SETTING
2
Figure 25. Function Latch Map
Rev. D | Page 14 of 20
Data Sheet
ADF4107
FASTLOCK
ENABLE
CP THREESTATE
PD
POLARITY
POWERDOWN 1
COUNTER
RESET
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
F4
F3
F2
M3
M2
M1
PD1
F1
POWERDOWN 2
FASTLOCK
MODE
INITIALIZATION LATCH MAP
PRESCALER
VALUE
P1
PD2
CPI6
CPI5
CPI4
CPI3
CPI2
TIMER COUNTER
CONTROL
CPI1
TC4
TC3
TC2
TC1
TC4
TC3
TC2
TC1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
3kΩ
1.06
2.12
3.18
4.24
5.30
6.36
7.42
8.50
5.1kΩ
0.625
1.25
1.875
2.5
3.125
3.75
4.375
5.0
CPI6
CPI5
CPI4
CPI3
0
0
0
0
1
1
1
1
CPI2
0
0
1
1
0
0
1
1
CPI1
0
1
0
1
0
1
0
1
PD2
PD1
MODE
X
X
0
1
X
0
1
1
ASYNCHRONOUS POWER-DOWN
NORMAL OPERATION
ASYNCHRONOUS POWER-DOWN
SYNCHRONOUS POWER-DOWN
P1
PRESCALER VALUE
0
1
0
1
8/9
16/17
32/33
64/65
PHASE DETECTOR
POLARITY
F1
0
1
NEGATIVE
POSITIVE
0
1
F3
CHARGE PUMP
OUTPUT
0
1
NORMAL
THREE-STATE
F4
F5
FASTLOCK MODE
0
1
1
X
0
1
FASTLOCK DISABLED
FASTLOCK MODE 1
FASTLOCK MODE 2
TIMEOUT
(PFD CYCLES)
3
7
11
15
19
23
27
31
35
39
43
47
51
55
59
63
DB1
DB0
C2 (1) C1 (1)
COUNTER
OPERATION
NORMAL
R, A, B COUNTERS
HELD IN RESET
M3
M2
M1
OUTPUT
0
0
0
0
0
1
0
0
1
1
1
1
0
0
0
1
0
1
1
1
1
1
0
1
THREE-STATE OUTPUT
DIGITAL LOCK DETECT
(ACTIVE HIGH)
N DIVIDER OUTPUT
DVDD
R DIVIDER OUTPUT
N-CHANNEL OPEN-DRAIN
LOCK DETECT
SERIAL DATA OUTPUT
DGND
11kΩ
0.289
0.580
0.870
1.160
1.450
1.730
2.020
2.320
CE PIN
0
0
1
1
F2
CONTROL
BITS
ICP (mA)
0
1
1
1
P2
F5
MUXOUT
CONTROL
03338-026
P2
CURRENT
SETTING
1
CURRENT
SETTING
2
Figure 26. Initialization Latch Map
Rev. D | Page 15 of 20
ADF4107
Data Sheet
FUNCTION LATCH
Fastlock Mode Bit
The on-chip function latch is programmed with C2 and C1 set
to 1 and 0, respectively. Figure 25 shows the input data format
for programming the function latch.
DB10 of the function latch is the fastlock mode bit. When
fastlock is enabled, this bit determines which fastlock mode is
used. If the fastlock mode bit is 0, then Fastlock Mode 1 is
selected; and if the fastlock mode bit is 1, then Fastlock Mode 2
is selected.
Counter Reset
DB2 (F1) is the counter reset bit. When this bit is 1, the R
counter and the AB counters are reset. For normal operation,
this bit should be 0. Upon powering up, the F1 bit needs to be
disabled (set to 0). Then, the N counter resumes counting in
close alignment with the R counter. (The maximum error is one
prescaler cycle).
Fastlock Mode 1
The charge pump current is switched to the contents of Current
Setting 2. The device enters fastlock by having a 1 written to the
CP gain bit in the AB counter latch. The device exits fastlock by
having a 0 written to the CP gain bit in the AB counter latch.
Power-Down
Fastlock Mode 2
DB3 (PD1) and DB21 (PD2) provide programmable powerdown modes. They are enabled by the CE pin.
The charge pump current is switched to the contents of Current
Setting 2. The device enters fastlock by having a 1 written to the
CP gain bit in the AB counter latch. The device exits fastlock
under the control of the timer counter. After the timeout period
determined by the value in TC4 to TC1, the CP gain bit in the
AB counter latch is automatically reset to 0 and the device
reverts to normal mode instead of fastlock. See Figure 25 for the
timeout periods.
When the CE pin is low, the device is immediately disabled
regardless of the states of PD2 and PD1.
In the programmed asynchronous power-down, the device
powers down immediately after latching a 1 into the PD1 bit,
with the condition that PD2 has been loaded with a 0.
In the programmed synchronous power-down, the device
power-down is gated by the charge pump to prevent unwanted
frequency jumps. Once the power-down is enabled by writing
a 1 into PD1 (on condition that a 1 has also been loaded to
PD2), then the device goes into power-down on the occurrence
of the next charge pump event.
When a power-down is activated (either in synchronous or
asynchronous mode, including CE pin-activated power-down),
the following events occur:
•
All active dc current paths are removed.
•
The R, N, and timeout counters are forced to their load state
conditions.
•
The charge pump is forced into three-state mode.
•
The digital lock detect circuitry is reset.
•
The RFIN input is debiased.
•
The reference input buffer circuitry is disabled.
•
The input register remains active and capable of loading and
latching data.
MUXOUT Control
The on-chip multiplexer is controlled by M3, M2, and M1 on
the ADF4107. Figure 25 shows the truth table.
Fastlock Enable Bit
DB9 of the function latch is the fastlock enable bit. Fastlock is
enabled only when this bit is 1.
Timer Counter Control
The user has the option of programming two charge pump
currents. The intent is that Current Setting 1 is used when the RF
output is stable and the system is in a static state. Current Setting 2
is meant to be used when the system is dynamic and in a state of
change (that is, when a new output frequency is programmed).
The normal sequence of events is as follows:
The user initially decides what the preferred charge pump
currents are going to be. For example, the choice may be 2.5 mA
as Current Setting 1 and 5 mA as Current Setting 2.
At the same time, it must be decided how long the secondary
current is to stay active before reverting to the primary current.
This is controlled by the timer counter control bits, DB14 to
DB11 (TC4 to TC1), in the function latch. The truth table is
given in Figure 25.
To program a new output frequency, the user simply programs
the AB counter latch with new values for A and B. At the same
time, the CP gain bit can be set to 1, which sets the charge
pump with the value in CPI6 to CPI4 for a period of time
determined by TC4 to TC1. When this time is up, the charge
pump current reverts to the value set by CPI3 to CPI1. At the
same time, the CP gain bit in the AB counter latch is reset to 0
and is ready for the next time that the user wishes to change the
frequency.
Note that there is an enable feature on the timer counter. It is
enabled when Fastlock Mode 2 is chosen by setting the fastlock
mode bit (DB10) in the function latch to 1.
Rev. D | Page 16 of 20
Data Sheet
ADF4107
Charge Pump Currents
5.
Then do an AB load (01 in two LSBs).
CPI3, CPI2, and CPI1 program Current Setting 1 for the charge
pump. CPI6, CPI5, and CPI4 program Current Setting 2 for the
charge pump. The truth table is given in Figure 25.
6.
When the initialization latch is loaded, the following
occurs:
a.
b.
The function latch contents are loaded.
An internal pulse resets the R, AB, and timeout counters to
load-state conditions and also three-states the charge
pump. Note that the prescaler band gap reference and the
oscillator input buffer are unaffected by the internal reset
pulse, allowing close phase alignment when counting
resumes.
Latching the first AB counter data after the initialization
word activates the same internal reset pulse. Successive AB
loads do not trigger the internal reset pulse unless there is
another initialization.
Prescaler Value
P2 and P1 in the function latch set the prescaler values. The
prescaler value should be chosen so that the prescaler output
frequency is always less than or equal to 300 MHz. Thus, with
an RF frequency of 4 GHz, a prescaler value of 16/17 is valid but
a value of 8/9 is not valid.
PD Polarity
c.
This bit sets the phase detector polarity bit. See Figure 25.
CP Three-State
This bit controls the CP output pin. With the bit set high, the
CP output is put into three-state. With the bit set low, the CP
output is enabled.
INITIALIZATION LATCH
The initialization latch is programmed when C2 and C1 are set
to 1 and 1. This is essentially the same as the function latch
(programmed when C2, C1 = 1, 0).
However, when the initialization latch is programmed an
additional internal reset pulse is applied to the R and AB
counters. This pulse ensures that the AB counter is at load point
when the AB counter data is latched and the device will begin
counting in close phase alignment.
CE Pin Method
1. Apply VDD.
2. Bring CE low to put the device into power-down. This is
an asychronous power-down in that it happens immediately.
3. Program the function latch (10).
4. Program the R counter latch (00).
5. Program the AB counter latch (01).
6. Bring CE high to take the device out of power-down. The
R and AB counters resume counting in close alignment.
Note that after CE goes high, a duration of 1 µs may be required
for the prescaler band gap voltage and oscillator input buffer
bias to reach steady state.
If the latch is programmed for synchronous power-down (CE
pin is high; PD1 bit is high; PD2 bit is low), the internal pulse
also triggers this power-down. The prescaler reference and the
oscillator input buffer are unaffected by the internal reset pulse and
so close phase alignment is maintained when counting resumes.
CE can be used to power the device up and down in order to
check for channel activity. The input register does not need to
be reprogrammed each time the device is disabled and enabled
as long as it has been programmed at least once after VDD was
initially applied.
When the first AB counter data is latched after initialization, the
internal reset pulse is again activated. However, successive AB
counter loads after this will not trigger the internal reset pulse.
Counter Reset Method
1. Apply VDD.
2. Do a function latch load (10 in two LSBs). As part of this,
load 1 to the F1 bit. This enables the counter reset.
3. Do an R counter load (00 in two LSBs).
4. Do an AB counter load (01 in two LSBs).
5. Do a function latch load (10 in two LSBs). As part of this,
load 0 to the F1 bit. This disables the counter reset.
DEVICE PROGRAMMING AFTER INITIAL POWER-UP
After initially powering up the device, there are three ways to
program the device.
Initialization Latch Method
1. Apply VDD.
2. Program the initialization latch (11 in two LSBs of input
word). Make sure that the F1 bit is programmed to 0.
3. Next, do a function latch load (10 in two LSBs of the
control word), making sure that the F1 bit is programmed
to a 0.
4. Then do an R load (00 in two LSBs).
This sequence provides the same close alignment as the
initialization method. It offers direct control over the internal
reset. Note that counter reset holds the counters at load point
and three-states the charge pump, but does not trigger
synchronous power-down.
Rev. D | Page 17 of 20
ADF4107
Data Sheet
APPLICATIONS
Other PLL system specifications are:
LOCAL OSCILLATOR FOR LMDS BASE STATION
TRANSMITTER
KD = 5.0 mA
KV = 80 MHz/V
Loop bandwidth = 70 kHz
FPFD = 1 MHz
N = 6300
Extra reference spur attenuation = 10 dB
Figure 27 shows the ADF4107 being used with a VCO to
produce the LO for an LMDS base station.
The reference input signal is applied to the circuit at FREFIN
and, in this case, is terminated in 50 Ω. A typical base station
system has either a TCXO or an OCXO driving the reference
input without any 50 Ω termination.
All of these specifications are needed and used to derive the
loop filter component values shown in Figure 27.
To have a channel spacing of 1 MHz at the output, the 10 MHz
reference input must be divided by 10, using the on-chip
reference divider of the ADF4107.
Figure 27 gives a typical phase noise performance of −83 dBc/Hz
at 1 kHz offset from the carrier. Spurs are better than −70 dBc.
The loop filter output drives the VCO, which, in turn, is fed
back to the RF input of the PLL synthesizer, and drives the RF
output terminal. A T-circuit configuration provides 50 Ω
matching between the VCO output, the RF output, and the RFIN
terminal of the synthesizer.
The charge pump output of the ADF4107 (Pin 2) drives the
loop filter. In calculating the loop filter component values, a
number of items need to be considered. In this example, the
loop filter was designed so that the overall phase margin for the
system would be 45°.
In a PLL system, it is important to know when the system is in
lock. In Figure 27, this is accomplished by using the MUXOUT
signal from the synthesizer. The MUXOUT pin can be
programmed to monitor various internal signals in the
synthesizer. One of these is the LD or lock detect signal.
VDD
VP
RFOUT
100pF
7
1000pF
1000pF
FREFIN
16
15
VCC
2
7.5kΩ
100pF
51Ω
100pF
14
1.7kΩ
AVDD DVDD VP
CP 2
8 REFIN
47pF
10
V956ME01
18Ω
18Ω
18Ω
ADF4107
CE
CLK
DATA
LE
MUXOUT 14
1, 3, 4, 5, 7, 8,
9, 11, 12, 13
LOCK
DETECT
100pF
RFINA 6
51Ω
RFINB 5
DGND
3
4
9
100pF
NOTES:
1. DECOUPLING CAPACITORS (0.1µF/10pF) ON AVDD, DVDD, AND
VP OF THE ADF4106 AND ON VCC OF THE V956ME03 HAVE
BEEN OMITTED FROM THE DIAGRAM TO AID CLARITY.
03338-027
5.1kΩ
RSET
AGND
1
CPGND
SPI®-COMPATIBLE SERIAL BUS
820pF
Figure 27. 6.3 GHz Local Oscillator Using the ADF4107
Rev. D | Page 18 of 20
Data Sheet
ADF4107
INTERFACING
ADSP-2181 Interface
The ADF4107 has a simple SPI®-compatible serial interface for
writing to the device. CLK, DATA, and LE control the data
transfer. When LE (latch enable) goes high, the 24 bits that have
been clocked into the input register on each rising edge of CLK
are transferred to the appropriate latch. See Figure 2 for the
timing diagram and Table 5 for the latch truth table.
Figure 29 shows the interface between the ADF4107 and the
ADSP21xx digital signal processor. The ADF4107 needs a
24-bit serial word for each latch write. The easiest way to
accomplish this using the ADSP-21xx family is to use the
autobuffered transmit mode of operation with alternate
framing. This provides a means for transmitting an entire block
of serial data before an interrupt is generated. Set up the word
length for 8 bits and use three memory locations for each 24-bit
word. To program each 24-bit latch, store the three 8-bit bytes,
enable the autobuffered mode, and then write to the transmit
register of the DSP. This last operation initiates the autobuffer
transfer.
ADuC812 Interface
Figure 28 shows the interface between the ADF4107 and the
ADuC812 MicroConverter®. Since the ADuC812 is based on an
8051 core, this interface can be used with any 8051-based
microcontroller. The MicroConverter is set up for SPI master
mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Each latch of the ADF4107 needs a
24-bit word. This is accomplished by writing three 8-bit bytes
from the MicroConverter to the device. When the third byte
has been written, the LE input should be brought high to
complete the transfer.
On first applying power to the ADF4107, it needs four writes
(one each to the initialization latch, function latch, R counter
latch, and N counter latch) for the output to become active.
I/O port lines on the ADuC812 are also used to control powerdown (CE input) and to detect lock (MUXOUT configured as
lock detect and polled by the port input).
When operating in the mode described, the maximum
SCLOCK rate of the ADuC812 is 4 MHz. This means that the
maximum rate at which the output frequency can be changed is
166 kHz.
MOSI
CLK
DATA
LE
ADuC812
I/O PORTS
ADF4107
CE
MUXOUT
(LOCK DETECT)
Figure 28. ADuC812 to ADF4107 Interface
03338-028
SCLOCK
SCLOCK
DT
ADSP-21xx
TFS
CLK
DATA
LE
ADF4107
CE
I/O FLAGS
MUXOUT
(LOCK DETECT)
03338-029
The maximum allowable serial clock rate is 20 MHz. This
means that the maximum update rate possible for the device is
833 kHz or one update every 1.2 µs. This is certainly more than
adequate for systems that have typical lock times in hundreds of
microseconds.
Figure 29. ADSP-21xx to ADF4107 Interface
PCB DESIGN GUIDELINES FOR CHIP SCALE
PACKAGE
The lands on the chip scale package (CP-20-6) are rectangular.
The printed circuit board pad for these should be 0.1 mm
longer than the package land length and 0.05 mm wider than
the package land width. The land should be centered on the
pad. This ensures that the solder joint size is maximized. The
bottom of the chip scale package has a central thermal pad.
The thermal pad on the printed circuit board should be at least
as large as this exposed pad. On the printed circuit board, there
should be a clearance of at least 0.25 mm between the thermal
pad and the inner edges of the pad pattern. This ensures that
shorting is avoided.
Thermal vias may be used on the printed circuit board thermal
pad to improve thermal performance of the package. If vias are
used, they should be incorporated in the thermal pad at 1.2 mm
pitch grid. The via diameter should be between 0.3 mm and
0.33 mm and the via barrel should be plated with 1 oz. copper
to plug the via.
The user should connect the printed circuit board thermal pad
to AGND.
Rev. D | Page 19 of 20
ADF4107
Data Sheet
OUTLINE DIMENSIONS
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.30
0.19
0.65
BSC
COPLANARITY
0.10
0.75
0.60
0.45
8°
0°
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 30. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
PIN 1
INDICATOR
0.30
0.25
0.18
0.50
BSC
PIN 1
INDICATOR
20
16
15
1
EXPOSED
PAD
2.30
2.10 SQ
2.00
11
0.65
0.60
0.55
TOP VIEW
0.80
0.75
0.70
5
10
0.20 MIN
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
6
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WGGD-1.
ORDERING GUIDE
08-16-2010-B
4.10
4.00 SQ
3.90
Figure 31. 20-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
4 mm × 4 mm Body, Very Very Thin Quad
(CP-20-6)
Dimensions shown in millimeters
Model 1
Temperature Range
Package Description
Package Option
ADF4107BRU
ADF4107BRU-REEL
ADF4107BRU-REEL7
ADF4107BRUZ
ADF4107BRUZ-REEL
ADF4107BRUZ-REEL7
ADF4107BCPZ
ADF4107BCPZ-REEL
ADF4107BCPZ-REEL7
EV-ADF411XSD1Z
–40°C to + 85°C
–40°C to + 85°C
–40°C to + 85°C
–40°C to + 85°C
–40°C to + 85°C
–40°C to + 85°C
–40°C to + 85°C
–40°C to + 85°C
–40°C to + 85°C
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
16-Lead Thin Shrink Small Outline Package [TSSOP]
20-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
20-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
20-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
Evaluation Board
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
CP-20-6
CP-20-6
CP-20-6
1
Z = RoHS Compliant Part.
©2003–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03338-0-3/13(D)
Rev. D | Page 20 of 20
Similar pages