HT11 - HT18 1.0 AMP. High Efficient Rectifiers TS-1 Features High efficiency, Low VF High current capability High reliability High surge current capability For use in low voltage, high frequency inventor, free wheeling, and polarity protection application. Mechanical Data Case: Molded plastic TS-1 Epoxy: UL 94V0 rate flame retardant Lead: Pure tin plated, lead free , solderable per MIL-STD-202, Method 208 guaranteed Polarity: Color band denotes cathode High temperature soldering guaranteed: 260 oC/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs., (2.3kg) tension Mounting position: Any Weight: 0.20 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375 (9.5mm) Lead Length o @T A = 55 C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A o Maximum DC Reverse Current @ T A =25 C o at Rated DC Blocking Voltage @ T A =125 C Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance Typical Thermal Resistance Operating Temperature Range ( Note 2 ) Symbol HT HT 11 12 V RRM 50 100 V RMS 35 70 V DC 50 100 HT 13 200 140 200 HT 14 300 210 300 HT 15 400 280 400 HT 16 600 420 600 HT 17 800 560 800 HT Units 18 1000 V 700 V 1000 V I(AV) 1.0 A IFSM 30 A VF 1.0 1.3 5.0 150 IR Trr Cj R θJA TJ 1.7 50 20 75 15 100 -65 to +150 -65 to +150 Storage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mount on Cu-Pad Size 5mm x 5mm on PCB. V uA uA nS pF o C/W o C o C Version: A06 RATINGS AND CHARACTERISTIC CURVES (HT11 THRU HT18) FIG.2- TYPICAL REVERSE CHARACTERISTICS FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 1000 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 1.0 0 0 25 50 75 100 125 150 175 O AMBIENT TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) 2.0 100 Tj=100 0C 10 Tj=75 0C 1 Tj=25 0C 35 0.1 0 40 60 80 100 120 140 8.3ms Single Half Sine Wave JEDEC Method 25 20 FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 15 10 10 0 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 70 JUNCTION CAPACITANCE.(pF) 20 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 30 INSTANTANEOUS FORWARD CURRENT. (A) PEAK FORWARD SURGE CURRENT. (A) 40 60 50 40 HT 30 11~ H HT1 20 T15 6~H T18 1.0 HT11~HT14 HT 15 0.1 0.01 HT16~HT18 10 0 0.001 0.1 0.5 1 2 5 10 20 50 100 200 500 1000 0 0.2 REVERSE VOLTAGE. (V) 0.4 0.6 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (+) 50Vdc (approx) (-) (-) DUT NON INDUCTIVE PULSE GENERATOR (NOTE 2) OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06