HI-1565, HI-1566 MIL-STD-1553 / 1760 5V Monolithic Dual Transceivers August 2006 DESCRIPTION PIN CONFIGURATIONS To minimize the package size for this function, the transmitter outputs are internally connected to the receiver inputs, so that only two pins are required for connection to each coupling transformer. FEATURES ! Compliant to MIL-STD-1553A & B, MIL-STD-1760, ARINC 708A ! CMOS technology for low standby power ! Smallest footprint available in 44-pin plastic 1565PCI 1565PCT 1566PCI 1566PCT 33 32 31 TXINHA 30 RXA 29 RXA 28 27 26 TXB 25 TXB 24 TXINHB 23 - 12 13 14 15 16 17 18 19 20 21 22 The receiver section of each channel converts the 1553 bus bi-phase data to complementary CMOS / TTL data suitable for inputting to a Manchester decoder. Each receiver has a separate enable input which can be used to force the output of the receiver to a logic 0 (HI-1565) or logic 1 (HI-1566). - 1 RXENA 2 GNDA 3 GNDA 4 GNDA 5 VDDB 6 VDDB 7 BUSB 8 BUSB 9 BUSB 10 BUSB 11 RXENB GNDB GNDB GNDB RXB RXB - The transmitter section of each channel takes complementary CMOS / TTL digital input data and converts it to bi-phase Manchester encoded 1553 signals suitable for driving the bus isolation transformer. Separate transmitter inhibit control signals are provided for each transmitter. 44 43 BUSA 42 BUSA 41 BUSA 40 BUSA 39 VDDA 38 VDDA 37 TXA 36 TXA 35 34 - The HI-1565 and HI-1566 are low power CMOS dual transceivers designed to meet the requirements of the MIL-STD-1553 /1760 specifications. 44 Pin Plastic 7mm x 7mm Chip-scale package VDDA 1 BUSA 2 BUSA 3 RXENA 4 GNDA 5 VDDB 6 BUSB 7 BUSB 8 RXENB 9 GNDB 10 1565PSI 1565PST 1565PSM 1565PSI 1565PST 1565PSM 20 19 18 17 16 15 14 13 12 11 TXA TXA TXINHA RXA RXA TXB TXB TXINHB RXB RXB 20 Pin Plastic ESOIC - WB package chip-scale package with integral heatsink VDDA 1 20 TXA ! Less than 1.0W maximum power dissipation ! BUS pins ESD protected to greater than 8KV ! Also available in DIP and small outline BUSA 2 19 TXA (ESOIC) package options ! Military processing options ! Industry standard pin configurations BUSA 3 RXENA 4 1565CDI 1565CDT 1565CDM BUSB 7 BUSB 8 17 RXA 16 RXA GNDA 5 VDDB 6 18 TXINHA 1566CDI 1566CDT 1566CDM 15 TXB 14 TXB 13 TXINHB RXENB 9 12 RXB GNDB 10 11 RXB 20 Pin Ceramic DIP package (DS1565 Rev. A) HOLT INTEGRATED CIRCUITS www.holtic.com 08/06 HI-1565, HI-1566 PIN DESCRIPTIONS PIN (DIP/ESOIC) SYMBOL FUNCTION DESCRIPTION 1 VDDA power supply +5 volt power for channel A 2 BUSA analog output MIL-STD-1533 bus driver A, positive signal 3 BUSA analog output MIL-STD-1553 bus driver A, negative signal 4 RXENA digital input 5 GNDA power supply Ground for channel A 6 VDDB power supply +5 volt power for channel B Receiver A enable. If low, forces RXA and RXA low (HI-1565) or High (HI-1566) 7 BUSB analog output MIL-STD-1533 bus driver B, positive signal 8 BUSB analog output MIL-STD-1553 bus driver B, negative signal 9 RXENB digital input 10 GNDB power supply Ground for channel B 11 RXB digital output Receiver B output, inverted 12 RXB digital output Receiver B output, non-inverted 13 TXINHB digital input Transmit inhibit, channel B. If high BUSB, BUSB disabled 14 TXB digital input Transmitter B digital data input, non-inverted 15 TXB digital input Transmitter B digital data input, inverted Receiver B enable. If low, forces RXB and RXB low (HI-1565) or High (HI-1566) 16 RXA digital output Receiver A output, inverted 17 RXA digital output Receiver A output, non-inverted 18 TXINHA digital input Transmit inhibit, channel A. If high BUSA, BUSA disabled 19 TXA digital input Transmitter A digital data input, non-inverted 20 TXA digital input Transmitter A digital data input, inverted FUNCTIONAL DESCRIPTION The HI-1565 family of data bus transceivers contain differential voltage source drivers and differential receivers. They are intended for applications using a MIL-STD-1553 A/B data bus. The device produces a trapezoidal output waveform during transmission. TRANSMITTER Data input to the device’s transmitter section is from the complementary CMOS /TTL inputs TXA/B and TXA/B. The transmitter accepts Manchester II bi-phase data and converts it to differential voltages on BUSA/B and BUSA/B. The transceiver outputs are either direct or transformer coupled to the MIL-STD-1553 data bus. Both coupling methods produce a nominal voltage on the bus of 7.5 volts peak to peak. The transmitter is automatically inhibited and placed in the high impedance state when both TXA/B and TXA/B are either at a logic “1” or logic “0” simultaneously. A logic “1” applied to the TXINHA/B input will force the transmitter to the high impedance state, regardless of the state of TXA/B and TXA/B. RECEIVER The receiver accepts bi-phase differential data from the MIL-STD-1553 bus through the same direct or transformer coupled interface as the transmitter. The receiver’s differential input stage drives a filter and threshold comparator that produces CMOS/TTL data at the RXA/B and RXA/B output pins. Each set of receiver outputs can be independently forced to a logic "0" (HI-1565) or logic “1” (HI-1566) by setting RXENA or RXENB low. MIL-STD-1553 BUS INTERFACE A direct coupled interface (see Figure 2) uses a 1:2.5 ratio isolation transformer and two 55 ohm isolation resistors between the transformer and the bus. In a transformer coupled interface (see Figure 3), the transceiver is connected to a 1:1.79 isolation transformer which in turn is connected to a 1:1.4 coupling transformer. The transformer coupled method also requires two coupling resistors equal to 75% of the bus characteristic impedence (Zo) between the coupling transformer and the bus. HOLT INTEGRATED CIRCUITS 2 HI-1565, HI-1566 Data Bus Each Channel TRANSMITTER Isolation Transformer Coupler Network BUSA/B TXA/B Transmit Logic Direct or Transformer Slope Control TXA/B BUSA/B TXINHA/B RECEIVER RXA/B Input Filter Receive Logic RXA/B Comparator RXENA/B Figure 1. Block Diagram TRANSMIT WAVEFORM - EXAMPLE PATTERN TXA/B TXA/B BUSA/B - BUSA/B RECEIVE WAVEFORMS - EXAMPLE PATTERN Vin (Line to Line) tDR tDR tDR RXA/B tRG tRG RXA/B HOLT INTEGRATED CIRCUITS 3 tDR HI-1565, HI-1566 RECOMMENDED OPERATING CONDITIONS ABSOLUTE MAXIMUM RATINGS Supply voltage (VDD) Logic input voltage range Supply Voltage -0.3 V to +7 V VDD....................................... 5V... ±5% -0.3 V dc to +5.5 V Receiver differential voltage 10 Vp-p Temperature Range Driver peak output current +1.0 A Power dissipation at 25°C ceramic DIL, derate 1.0 W 7mW/°C Solder Temperature Industrial Screening.........-40°C to +85°C Hi-Temp Screening........-55°C to +125°C Military Screening..........-55°C to +125°C NOTE: Stresses above absolute maximum ratings or outside recommended operating conditions may cause permanent damage to the device. These are stress ratings only. Operation at the limits is not recommended. 275°C for 10 sec. Junction Temperature 175°C Storage Temperature -65°C to +150°C DC ELECTRICAL CHARACTERISTICS VDD = 5.0V, GND = 0V, TA = Operating Temperature Range (unless otherwise specified). PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS 4.75 5 5.25 V Operating Voltage VDD Total Supply Current ICC1 Not Transmitting 14 22 mA ICC2 Transmit one channel @ 50% duty cycle 200 340 mA ICC3 Transmit one channel @ 100% duty cycle 400 550 mA 0.11 W 0.95 W Power Dissipation PD1 Not Transmitting PD2 Transmit one channel @ 100% duty cycle 0.70 Min. Input Voltage (HI) VIH Digital inputs Max. Input Voltage (LO) VIL Digital inputs Min. Input Current (HI) IIH VIH = 4.9V, Digital inputs Max. Input Current (LO) IIL VIL = 0.1V, Digital inputs -20 µA Min. Output Voltage (HI) VOH IOUT = -0.4mA, Digital outputs 2.7 V (LO) VIH IOUT = 4.0mA, Digital outputs Max. Output Voltage RECEIVER 2.0 1.4 1.4 V 0.8 V 20 µA 0.4 V (Measured at Point “AD“ in Figure 2 unless otherwise specified) Input resistance RIN Differential Input capacitance CIN Differential Common mode rejection ratio CMRR Input Level VIN Input common mode voltage Threshold Voltage - Direct-coupled Detect VTHD VTHND Threshold Voltage - Transformer-coupled Detect VTHD No Detect VTHND Kohm 5 40 Differential pF dB 9 Vp-p -5.0 5.0 V-pk 1 Mhz Sine Wave (Measured at Point “AD“ in Figure 2) 1.15 20.0 Vp-p 0.28 Vp-p 1 MHz Sine Wave (Measured at Point “AT“ in Figure 3) 0.86 14.0 Vp-p 0.20 Vp-p VICM No Detect 20 HOLT INTEGRATED CIRCUITS 4 HI-1565, HI-1566 DC ELECTRICAL CHARACTERISTICS (cont.) VDD = 5.0V, GND = 0V, TA = Operating Temperature Range (unless otherwise specified). PARAMETER TRANSMITTER SYMBOL CONDITION MIN TYP MAX UNITS 7.0 9.0 Vp-p 20.0 27.0 Vp-p 10.0 mVp-p -90 90 mV -250 250 mV (Measured at Point “AD” in Figure 2 unless otherwise specified) Output Voltage Direct coupled VOUT Transformer coupled VOUT Output Noise 35 ohm load (Measured at Point “AD“ in Figure 2) 70 ohm load (Measured at Point “AT“ in Figure 3) VON Output Dynamic Offset Voltage Direct coupled VDYN Transformer coupled VDYN Differential, inhibited 35 ohm load (Measured at Point “AD“ in Figure 2) 70 ohm load (Measured at Point “AT“ in Figure 3) Output resistance ROUT Differential, not transmitting Output Capacitance COUT 1 MHz sine wave 10 Kohm 15 pF AC ELECTRICAL CHARACTERISTICS VDD = 5.0V, GND = 0V, TA =Operating Temperature Range (unless otherwise specified). PARAMETER RECEIVER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS 450 ns 365 ns 40 ns (Measured at Point “AD” in Figure 2) Receiver Delay tDR From input zero crossing to RXA/B or RXA/B Receiver gap time tRG Spacing between RXA/B and RXA/B pulses Receiver Enable Delay tREN 90 From RXENA/B rising or falling edge to RXA/B or RXA/B TRANSMITTER (Measured at Point “AD” in Figure 2) Driver Delay tDT TXA/B, TXA/B to BUSA/B, BUSA/B 150 ns Rise time tr 35 ohm load 100 300 ns Fall Time tf 35 ohm load 100 300 ns tDI-H Inhibited output 100 ns tDI-L Active output 150 ns Inhibit Delay TRANSMITTER 1:2.5 55 W BUSA/B TXA/B 35 W TXA/B BUSA/B TXINHA/B 55 W Isolation Transformer Point “AD“ 55 W RECEIVER 2.5:1 RXA/B Point “AD“ 35 W 55 W RXA/B Isolation Transformer RXENA/B Figure 2. Direct Coupled Test Circuits HOLT INTEGRATED CIRCUITS 5 HI-1565, HI-1566 TRANSMITTER Point “AT” 1:1.79 52.5 W (.75 Zo) 1:1.4 BUSA/B TXA/B 35 W (.5 Zo) TXA/B BUSA/B TXINHA/B 52.5 W (.75 Zo) Isolation Transformer 1.4:1 52.5 W (.75 Zo) Coupling Transformer Point “AT” 1.79:1 RECEIVER RXA/B 35 W (.5 Zo) 52.5 W (.75 Zo) RXA/B Coupling Transformer Isolation Transformer RXENA/B Figure 3. Transformer Coupled Test Circuits HEAT SINK - ESOIC & CHIP-SCALE PACKAGE Both the HI-1565PSI/T/M and HI-1566PSI/T/M use a 20-pin thermally enhanced SOIC package. The HI-1565PCI/T and HI-1566PCI/T use a plastic chip-scale package. These packages include a metal heat sink located on the bottom surface of the device. This heat sink should be soldered down to the printed circuit board for optimum thermal dissipation. The heat sink is electrically isolated and may be soldered to any convenient power or ground plane.. THERMAL CHARACTERISTICS PART NUMBER PACKAGE STYLE HI-1565PSI / T / M 20-pin Thermally enhanced plastic SOIC (ESOIC) HI-1566PSI / T / M HI-1565CDI / T / M HI-1566CDI / T / M HI-1565PCI / T HI-1566PCI / T JUNCTION TEMPERATURE CONDITION ØJA Heat sink unsoldered 54°C/W 62°C 122°C 162°C Heat sink soldered 47°C/W 57°C 117°C 157°C 20-pin Ceramic side-brazed DIP Socketed 62°C/W 69°C 129°C 169°C 44-pin Plastic chipscale package Heat sink unsoldered 49°C/W 59°C 119°C 159°C TA=25°C TA=85°C TA=125°C Data taken at VDD=5.0V, continuous transmission at 1Mbit/s, single transmitter enabled. APPLICATIONS NOTE Holt Applications Note AN-500 provides circuit design notes regarding the use of Holt's family of MIL-STD-1553 transceivers. Layout considerations, as well as recommended interface and protection components are included. HOLT INTEGRATED CIRCUITS 6 HI-1565, HI-1566 ORDERING INFORMATION HI - 156x xx x x (Plastic) PART NUMBER Blank F LEAD FINISH Tin / Lead (Sn / Pb) Solder 100% Matte Tin (Pb-free, RoHS compliant) PART NUMBER TEMPERATURE RANGE FLOW BURN IN I -40°C TO +85°C I NO T -55°C TO +125°C T NO M -55°C TO +125°C M YES PART NUMBER PACKAGE DESCRIPTION PC 44 PIN PLASTIC CHIP-SCALE (LPCC) PS 20 PIN PLASTIC ESOIC (Wide Body, Thermally Enhanced SOIC w/Heat Sink) PART NUMBER RXENA = 0 RXENB = 0 RXA RXA RXB RXB 1565 0 0 0 0 1566 1 1 1 1 HI - 156xCD x (Ceramic) PART NUMBER TEMPERATURE RANGE FLOW BURN IN I -40°C TO +85°C I NO Gold (Pb-free, RoHS compliant) T -55°C TO +125°C T NO Gold (Pb-free, RoHS compliant) M -55°C TO +125°C M YES PART NUMBER LEAD FINISH Tin / Lead (Sn / Pb) Solder RXENA = 0 RXENB = 0 PACKAGE RXA RXA RXB RXB DESCRIPTION 1565CD 0 0 0 0 20 PIN CERAMIC SIDE BRAZED DIP 1566CD 1 1 1 1 20 PIN CERAMIC SIDE BRAZED DIP RECOMMENDED TRANSFORMERS The HI-1565 and HI-1566 transceivers have been characterized for compliance with the electrical requirements of MIL-STD-1553 when used with the following MANUFACTURER Technotrol Premier Magnetics Technotrol Premier Magnetics transformers. Holt recommends the Premier Magnetics parts as offering the best combination of electrical performance, low cost and small footprint. PART NUMBER APPLICATION TURNS RATIO(S) DIMENSIONS TL1553-45 Isolation Dual tapped 1:1.79, 1:2.5 .630 x 630 x .155 inches PM-DB2725EX Isolation Dual tapped 1:1.79, 1:2.5 .500 x .500 x .375 inches TQ1553-2 Stub coupling 1:1.4 .625 x .625 x .250 inches PM-DB2702 Stub coupling 1:1.4 .625 x .500 x .250 inches HOLT INTEGRATED CIRCUITS 7 PACKAGE DIMENSIONS inches (millimeters) 20-PIN PLASTIC SMALL OUTLINE (ESOIC) - WB (Wide Body, Thermally Enhanced) .0105 ± .0015 (.2667 ± .0381) .5035 ± .0075 (12.789 ± .191) .4065 ± .0125 (10.325 ± .318) Top View Package Type: 24HEW Heat sink stud on bottom of package. .300 TYP. (7.620) Bottom View .215 TYP. (5.461) .296 ± .003 (7.518 ± .076) .025 Min.. (.635) SEE DETAIL A .018 TYP. (.457) .025 Min.. (.635) .090 ± .010 (2.286 ± .254) 0° to 8° .050 TYP (1.27) .033 ± .017 (.838 ± .432) .0075 ± .0035 (.191 ± .889) DETAIL A 20-PIN CERAMIC SIDE-BRAZED DIP PACKAGE TYPE: 20C 1.000 ± .010 (25.400 ± .254) .310 ± .010 (7.874 ± .254) .050 TYP. (1.270 TYP.) .200 MAX. (5.080 MAX.) .125 MIN. (3.175 MIN.) .300 ± .010 (7.620 ± .254) .085 ± .009 (2.159 ± .229) .017 ± .002 (.432 ± .051) .100 ± .005 (2.540 ± .127) HOLT INTEGRATED CIRCUITS 8 .010 + .002/- .001 (.254 + .051/- .025) PACKAGE DIMENSIONS millimeters 44-PIN PLASTIC CHIP-SCALE PACKAGE Heat sink stud on bottom of package. 7.00 ± .10 5.65 ± .15 0.50 7.00 ± .10 5.65 ± .15 0.25 typ 0.40 ± .05 0.90 ± .10 0.2 typ HOLT INTEGRATED CIRCUITS 9