STMicroelectronics HCF4038BC1 Triple serial adder Datasheet

HCC/HCF4032B
HCC/HCF4038B
TRIPLE SERIAL ADDERS
.
.
..
.
.
..
..
INVERT INPUTS ON ALL ADDERS FOR SUM
COMPLEMENTING APPLICATIONS
FULLY STATIC OPERATION...DC TO 10MHz
(typ.) @ VDD = 10V
BUFFERED INPUTS AND OUTPUTS
SINGLE-PHASE CLOCKING
STANDARDIZED SYMMETRICAL OUTPUT
CHARACTERISTICS
QUIESCENT CURRENT SPECIFIED TO 20V
FOR HCC DEVICE
5V, 10V, AND 15V PARAMETRIC RATING
INPUT CURRENT OF 100nA AT 18V AND 25°C
FOR HCC DEVICE
100% TESTED FOR QUIESCENT CURRENT
MEETS ALL REQUIREMENTS OF JEDEC TENTATIVE STANDARD N° 13A, ”STANDARD SPECIFICATIONS FOR DESCRIPTION OF ”B”
SERIES CMOS DEVICES”
EY
(Plastic Package)
M1
(Micro Package)
F
(Ceramic Package)
C1
(Plastic Chip Carrier)
ORDER CODES :
HCC40XXBF
HCF40XXBM1
HCF40XXBEY
HCF40XXBC1
PIN CONNECTIONS
DESCRIPTION
The HCC/4032B/4038B (extended temperature
range) and HCF4032B/4038B (intermediate temperature range) are monolithic integrated circuits,
available in 16-lead dual in-line plastic or ceramic
package and plastic micro package.
The HCC/HCF4032B and HCC/HCF4038B types
consist of three serial adder circuits with common
CLOCK and CARRY-RESET inputs. Each adder
has two provisions for two serial DATA INPUT signals and an INVERT command signal. When the
command signal is a logical ”1”, the sum is complemented. Data words enter the adder with the
least significant bit first ; the sign bit trails. The output
is the MOD 2 sum of the input bits plus the carry from
the previous bit position. The carry is only added at
the positive-going clock transition for the
HCC/HCF4032B or at the negative-going clock for
the HCC/HCF4038B, thus, for spike-free operation
the input data transitions should occur as soon as
possible after the triggering edge. The CARRY is
reset to a logical ”0” at the end of each word by applying a logical ”1” signal to a CARRY-RESET input
one-bit-position before the application of the first bit
of the next word.
June 1989
1/11
HCC/HCF4032B/4038B
FUNCTIONAL DIAGRAM
ABSOLUTE MAXIMUM RATINGS
Symbol
V DD*
Parameter
Supply Voltage : HC C Types
H C F Types
Vi
Input Voltage
II
Value
Unit
– 0.5 to + 20
– 0.5 to + 18
V
V
– 0.5 to V DD + 0.5
V
DC Input Current (any one input)
± 10
mA
Pt ot
Total Power Dissipation (per package)
Dissipation per Output Transistor
for T o p = Full Package-temperature Range
200
mW
100
mW
Top
Operating Temperature : HCC Types
H CF Types
– 55 to + 125
– 40 to + 85
°C
°C
Tstg
Storage Temperature
– 65 to + 150
°C
Stresses above those listed under ”Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections
of this specification is not implied. Exposure to absolute maximum rating conditions for external periods may affect device reliability.
* All voltage values are referred to VSS pin voltage.
RECOMMENDED OPERATING CONDITIONS
Symbol
V DD
VI
Top
2/11
Parameter
Supply Voltage : H CC Types
H C F Types
Input Voltage
Operating Temperature : HCC Types
H CF Types
Value
Unit
3 to 18
3 to 15
V
V
0 to V DD
V
– 55 to + 125
– 40 to + 85
°C
°C
HCC/HCF4032B/4038B
LOGIC AND TIMING DIAGRAMS
(one of three serial adders)
4032B
WORD 1
WORD 2
0.0111100 =
0.0110010 =
+ 60
+ 50
0.1101110 = + 110
WORD 3
WORD 4
1.1011011 =
1.1001110 =
– 37
– 50
1.0101001 =
– 87
3/11
HCC/HCF4032B/4038B
LOGIC AND TIMING DIAGRAMS (continued)
4038B
WORD 1
WORD 2
1.1000011 =
1.1001101 =
– 61
– 51
1.0010000 = – 112
4/11
WORD 3
WORD 4
0.0100100 =
0.0110001 =
+ 36
+ 49
0.1010101 =
+ 85
HCC/HCF4032B/4038B
STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions)
Test Conditions
Symbol
IL
VOH
VOL
Parameter
Quiescent
Current
VI
(V)
VO
(V)
VIL
IOH
CI
Max. Min.
Max.
150
HCC 0/10
Types 0/15
10
10
0.04
10
300
15
20
0.04
20
600
0/20
20
100
0.08
100
3000
0/ 5
HCF
0/10
Types
0/15
5
20
0.04
20
150
10
40
0.04
40
300
15
80
0.04
80
600
0/ 5
< 1
5
4.95
4.95
4.95
0/10
< 1
10
9.95
9.95
9.95
0/15
< 1
15
14.95
5/0
< 1
5
0.05
0.05
0.05
10/0
< 1
10
0.05
0.05
0.05
Input High
Voltage
Input Low
Voltage
Input
Leakage
Current
Typ.
5
14.95
< 1
15
0.5/4.5
< 1
5
3.5
0.05
3.5
0.05
3.5
1/9
< 1
10
7
7
7
1.5/13.5 < 1
15
11
11
11
< 1
5
1.5
1.5
1.5
9/1
< 1
10
3
3
3
13.5/1.5 < 1
15
4
4
– 1.6 – 3.2
–
1.15
0/ 5
4.6
5
–
0.64
–
0.51
–
0.36
0/10
9.5
10
– 1.6
– 1.3 – 2.6
– 0.9
0/15
13.5
15
– 4.2
– 3.4 – 6.8
– 2.4
0/ 5
2.5
5
–
1.53
–
– 3.2
1.36
– 1.1
0/ 5
4.6
5
–
0.52
–
0.44
–
0.36
0/10
9.5
10
– 1.3
– 1.1 – 2.6
– 0.9
0/15
13.5
15
– 3.6
– 3.0 – 6.8
– 2.4
0/ 5
0.4
5
0.64
0.51
1
0.36
HCC
0/10
Types
0/15
0.5
10
1.6
1.3
2.6
0.9
1.5
15
4.2
3.4
6.8
2.4
0/ 5
0.4
5
0.52
0.44
1
0.36
0.5
10
1.3
1.1
2.6
0.9
1.5
15
3.6
3.0
6.8
2.4
Input Capacitance
– 1
– 1
18
± 0.1
±10–5 ± 0.1
15
± 0.3
±10
mA
mA
± 1
Any Input
Any Input
V
4
– 2
HCF 0/15
Types
V
V
4.5/0.5
5
HCC
0/18
Types
V
0.05
2.5
HCC
Types
µA
14.95
0/ 5
HCF
0/10
Types
0/15
IIH, IIL
Max. Min.
Unit
T High*
0.04
Output Low
Voltage
Output
Sink
Cur rent
Min.
2 5° C
5
HCF
Types
IOL
TLow*
5
Output High
Voltage
Output
Drive
Current
Value
V DD
(V)
0/ 5
15/0
VIH
| I O|
(µA)
µA
5
–5
± 0.3
7.5
± 1
pF
* TLo w = – 55°C for HCC device : – 40°C for HCF device.
* THigh = + 125°C for HCC device : + 85°C for HCF device.
The Noise Margin for both ”1” and ”0” level is : 1V min. with VDD = 5V, 2V min. with VDD = 10V, 2.5V min. with VDD = 15V.
5/11
HCC/HCF4032B/4038B
DYNAMIC ELECTRICAL CHARACTERISTICS (T amb = 25°C, C L = 50pF, R L = 200kΩ,
all input rise and fall time = 20ns)
Symbol
Parameter
t PHL ,
tP LH
Propagation Delay Time A, B, or
Inverter Inputs to Sum Outputs
t PHL ,
tP LH
Propagation Delay Time
(clock input to sum outputs)
Test Conditions
Value
V D D (V) Min.
Typ.
Max.
5
260
520
10
120
240
15
90
180
5
325
650
10
175
350
15
150
300
5
100
200
10
50
100
t T HL ,
t T HL
Transition Time
t h o ld
Data Input Hold Time
(clock edge to A, B, or reset
inputs)
Maximum Clock Input Frequency
5
f max
t r, t f *
Clock Input Rise or Fall Time
15
40
80
5
120
200
10
50
80
40
60
15
2.5
4.5
10
5
10
15
7.5
15
Unit
ns
ns
ns
MHz
5
500
10
500
15
500
µs
* If more than one unit is cascaded tr should be made less than or equal to the sum of the transition time and the fixed propagation delay of the output of the driving state for the estimated capacitive load.
Typical Output Low (sink) Current.
6/11
Minimum Output Low (sink) Current Characteristics.
HCC/HCF4032B/4038B
Typical Output High (source) Current Characteristics.
Minimum Output High (source) Current Characteristics.
TEST CIRCUITS
Quiescent Device Current.
Input Voltage.
Input Current.
7/11
HCC/HCF4032B/4038B
Plastic DIP16 (0.25) MECHANICAL DATA
mm
DIM.
MIN.
a1
0.51
B
0.77
TYP.
inch
MAX.
MIN.
TYP.
MAX.
0.020
1.65
0.030
0.065
b
0.5
0.020
b1
0.25
0.010
D
20
0.787
E
8.5
0.335
e
2.54
0.100
e3
17.78
0.700
F
7.1
0.280
I
5.1
0.201
L
Z
3.3
0.130
1.27
0.050
P001C
8/11
HCC/HCF4032B/4038B
Ceramic DIP16/1 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
20
0.787
B
7
0.276
D
E
3.3
0.130
0.38
e3
0.015
17.78
0.700
F
2.29
2.79
0.090
0.110
G
0.4
0.55
0.016
0.022
H
1.17
1.52
0.046
0.060
L
0.22
0.31
0.009
0.012
M
0.51
1.27
0.020
0.050
N
P
Q
10.3
7.8
8.05
5.08
0.406
0.307
0.317
0.200
P053D
9/11
HCC/HCF4032B/4038B
PLCC20 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
9.78
10.03
0.385
0.395
B
8.89
9.04
0.350
0.356
D
4.2
4.57
0.165
0.180
d1
2.54
0.100
d2
0.56
0.022
E
7.37
8.38
0.290
0.330
e
1.27
0.050
e3
5.08
0.200
F
0.38
0.015
G
0.101
0.004
M
1.27
0.050
M1
1.14
0.045
P027A
10/11
HCC/HCF4032B/4038B
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.
 1994 SGS-THOMSON Microelectronics - All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A
11/11