SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 D D D D D D Choice of Eight Latches or Eight D-Type Flip-Flops in a Single Package 3-State Bus-Driving Outputs Full Parallel Access for Loading Buffered Control Inputs Clock-Enable Input Has Hysteresis to Improve Noise Rejection (’S373 and ’S374) P-N-P Inputs Reduce DC Loading on Data Lines (’S373 and ’S374) SN54LS373, SN54LS374, SN54S373, SN54S374 . . . J OR W PACKAGE SN74LS373, SN74S374 . . . DW, N, OR NS PACKAGE SN74LS374 . . . DB, DW, N, OR NS PACKAGE SN74S373 . . . DW OR N PACKAGE (TOP VIEW) OC 1Q 1D 2D 2Q 3Q 3D 4D 4Q GND description 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 8Q 8D 7D 7Q 6Q 6D 5D 5Q C† † C for ’LS373 and ’S373; CLK for ’LS374 and ’S374. SN54LS373, SN54LS374, SN54S373, SN54S374 . . . FK PACKAGE (TOP VIEW) The eight latches of the ’LS373 and ’S373 are transparent D-type latches, meaning that while the enable (C or CLK) input is high, the Q outputs follow the data (D) inputs. When C or CLK is taken low, the output is latched at the level of the data that was set up. 2D 2Q 3Q 3D 4D 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 8D 7D 7Q 6Q 6D 4Q GND C† 5Q 5D The eight flip-flops of the ’LS374 and ’S374 are edge-triggered D-type flip-flops. On the positive transition of the clock, the Q outputs are set to the logic states that were set up at the D inputs. 20 2 1D 1Q OC VCC 8Q These 8-bit registers feature 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. The high-impedance 3-state and increased high-logic-level drive provide these registers with the capability of being connected directly to and driving the bus lines in a bus-organized system without need for interface or pullup components. These devices are particularly attractive for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. 1 † C for ’LS373 and ’S373; CLK for ’LS374 and ’S374. Schmitt-trigger buffered inputs at the enable/clock lines of the ’S373 and ’S374 devices simplify system design as ac and dc noise rejection is improved by typically 400 mV due to the input hysteresis. A buffered output-control (OC) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. OC does not affect the internal operation of the latches or flip-flops. That is, the old data can be retained or new data can be entered, even while the outputs are off. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 ORDERING INFORMATION TA PDIP – N 0°C to 70°C ORDERABLE PART NUMBER PACKAGE† SOIC – DW SOP – NS SSOP – DB CDIP – J –55°C to 125°C CFP – W LCCC – FK TOP-SIDE MARKING Tube SN74LS373N SN74LS373N Tube SN74LS374N SN74LS374N Tube SN74S373N SN74S373N Tube SN74S374N SN74S374N Tube SN74LS373DW Tape and reel SN74LS373DWR Tube SN74LS374DW Tape and reel SN74LS374DWR Tube SN74S373DW Tape and reel SN74S373DWR Tube SN74S374DW Tape and reel SN74S374DWR Tape and reel SN74LS373NSR 74LS373 Tape and reel SN74LS374NSR 74LS374 Tape and reel SN74S374NSR 74S374 Tape and reel SN74LS374DBR LS374A Tube SN54LS373J SN54LS373J Tube SNJ54LS373J SNJ54LS373J Tube SN54LS374J SN54LS374J Tube SNJ54LS374J SNJ54LS374J Tube SN54S373J SN54S373J Tube SNJ54S373J SNJ54S373J Tube SN54S374J SN54S374J Tube SNJ54S374J SNJ54S374J Tube SNJ54LS373W SNJ54LS373W Tube SNJ54LS374W SNJ54LS374W Tube SNJ54S374W SNJ54S374W Tube SNJ54LS373FK SNJ54LS373FK Tube SNJ54LS374FK SNJ54LS374FK Tube SNJ54S373FK SNJ54S373FK Tube SNJ54S374FK SNJ54S374FK LS373 LS374 S373 S374 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 Function Tables ’LS373, ’S373 (each latch) INPUTS OC C D OUTPUT Q L H H H L H L L L L X Q0 H X X Z ’LS374, ’S374 (each latch) INPUTS OC CLK D OUTPUT Q L ↑ H H L ↑ L L L L X Q0 H X X Z POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 logic diagrams (positive logic) ’LS373, ’S373 Transparent Latches OC C 1 OC 11 CLK C1 1D 3 4 3D 4D 5D 6D 7D 8D 16 1D 13 14 17 8D 18 for ’S373 Only 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 1D 16 1D 1D for ’S374 Only Pin numbers shown are for DB, DW, J, N, NS, and W packages. 12 1D C1 8Q 9 1D C1 7Q 7D 19 8 6 1D C1 6Q 6D 1D C1 18 15 7 5 1D C1 5Q 5D 1D C1 17 12 4 2 1D C1 4Q 4D 1D C1 14 9 3 C1 3Q 3D 1D C1 13 6 11 C1 2Q 2D 1D C1 8 5 1 C1 1Q 1D 1D C1 7 2 1D C1 2D ’LS374, ’S374 Positive-Edge-Triggered Flip-Flops 19 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 schematic of inputs and outputs ’LS373 EQUIVALENT OF DATA INPUTS EQUIVALENT OF ENABLE- AND OUTPUT-CONTROL INPUTS TYPICAL OF ALL OUTPUTS VCC VCC VCC 17 kΩ NOM Req = 20 kΩ NOM 100 Ω NOM Input Input Output ’LS374 EQUIVALENT OF DATA INPUTS VCC EQUIVALENT OF CLOCK- AND OUTPUT-CONTROL INPUTS TYPICAL OF ALL OUTPUTS VCC VCC 17 kΩ NOM 30 kΩ NOM 100 Ω NOM Input Input Output POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† (’LS devices) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. Voltage values are with respect to network ground terminal. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions SN54LS’ MIN NOM 4.5 5 SN74LS’ MAX MIN NOM MAX 5 4.75 5 5.25 UNIT VCC VOH Supply voltage High-level output voltage 5.5 5.5 V IOH IOL High-level output current –1 –2.6 mA 24 mA Low-level output current tw Pulse duration tsu Data setup time th Data hold time 12 CLK high 15 15 CLK low 15 15 ’LS373 5↓ 5↓ ’LS374 20↑ 20↑ ’LS373 ’LS374‡ 20↓ 20↓ 5↑ 0↑ V ns ns ns TA Operating free-air temperature –55 125 0 70 °C ‡ The th specification applies only for data frequency below 10 MHz. Designs above 10 MHz should use a minimum of 5 ns (commercial only). 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) TEST CONDITIONS† PARAMETER MIN SN54LS’ TYP‡ MAX 2 MIN SN74LS’ TYP‡ MAX 2 UNIT VIH VIL High-level input voltage VIK Input clamp voltage VCC = MIN, II = –18 mA VOH High level output voltage High-level VCC = MIN,, VIL = VIL max, VIH = 2 V,, IOH = MAX VOL Low level output voltage Low-level VCC = MIN,, VIL = VIL max VIH = 2 V,, VCC = MAX,, VO = 2.7 V VIH = 2 V,, 20 20 m A m A Low-level input voltage Off-state output current,, IOZH high-level voltage applied 24 2.4 IOL = 12 mA IOL = 24 mA 0.8 V –1.5 –1.5 V 34 3.4 0.25 V 0.7 24 2.4 31 3.1 0.4 V 0.25 0.4 0.35 0.5 IOZL Off-state output current,, low-level voltage applied VCC = MAX,, VO = 0.4 V VIH = 2 V,, –20 20 –20 20 II Input current at maximum input voltage VCC = MAX MAX, VI = 7 V 01 0.1 01 0.1 VI = 2.7 V VI = 0.4 V 20 20 IIH IIL High-level input current Low-level input current VCC = MAX, VCC = MAX, IOS Short-circuit output current§ VCC = MAX ICC Supply current VCC = MAX,, Output control at 4.5 V –0.4 –30 –130 –30 V mA m A –0.4 mA –130 mA ’LS373 24 40 24 40 ’LS374 27 40 27 40 mA † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. ‡ All typical values are at VCC = 5 V, TA = 25°C. § Not more than one output should be shorted at a time and duration of the short circuit should not exceed one second. switching characteristics, VCC = 5 V, TA = 25°C (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) TEST CONDITIONS ’LS373 MIN TYP ’LS374 MAX RL = 667 Ω, CL = 45 pF, See Note 3 fmax MIN TYP 35 50 MAX MHz tPLH tPHL Data Any Q RL = 667 Ω, CL = 45 pF,, See Note 3 12 18 12 18 tPLH tPHL C or CLK Any Q RL = 667 Ω, CL = 45 pF,, See Note 3 20 30 15 28 18 30 19 28 tPZH tPZL Any Q RL = 667 Ω, CL = 45 pF,, See Note 3 15 28 20 26 OC 25 36 21 28 25 15 28 Any Q RL = 667 Ω, CL = 5 pF 15 OC 12 20 12 20 tPHZ tPLZ UNIT ns ns ns ns NOTE 3: Maximum clock frequency is tested with all outputs loaded. fmax = maximum clock frequency tPLH = propagation delay time, low-to-high-level output tPHL = propagation delay time, high-to-low-level output tPZH = output enable time to high level tPZL = output enable time to low level tPHZ = output disable time from high level tPLZ = output disable time from low level POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 schematic of inputs and outputs ’S373 and ’S374 ’S373 and ’S374 TYPICAL OF ALL OUTPUTS EQUIVALENT OF EACH INPUT VCC VCC 50 Ω NOM 2.8 kΩ NOM Input Output 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† (’S devices) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Off-state output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Package thermal impedance, θJA (see Note 2): DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69°C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. Voltage values are with respect to network ground terminal. 2. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions SN54S’ SN74S’ MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.75 5 5.25 UNIT VCC VOH Supply voltage High-level output voltage 5.5 5.5 V IOH High-level output current –2 –6.5 mA tw Pulse duration, duration clock/enable tsu Data setup time th Data hold time TA Operating free-air temperature High 6 6 Low 7.3 7.3 ’S373 0↓ 0↓ ’S374 5↑ 5↑ ’S373 10↓ 10↓ ’S374 2↑ 2↑ –55 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 125 0 V ns ns ns 70 °C 9 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) (SN54S373, SN54S374, SN74S373, SN74S374) TEST CONDITIONS† PARAMETER MIN VIH VIL TYP‡ MAX 2 VIK VCC = MIN, II = –18 mA VCC = MIN MIN, VIH = 2 V V, VIL = 0 0.8 8V V, IOH = MAX VOL IOZH VCC = MIN, VCC = MAX, VIH = 2 V, VIH = 2 V, VIL = 0.8 V, VO = 2.4 V IOL = 20 mA IOZL II VCC = MAX, VCC = MAX, VIH = 2 V, VI = 5.5 V VO = 0.5 V IIH IIL VCC = MAX, VCC = MAX, VI = 2.7 V VI = 0.5 V IOS§ VCC = MAX VOH SN54S’ SN74S’ ICC V 2.4 3.4 2.4 3.1 VCC = MAX ’S374 0.8 V –1.2 V V 0.5 V 50 m A –50 m A 1 –40 ’S373 UNIT mA 50 m A –250 m A –100 mA Outputs high 160 Outputs low 160 Outputs disabled 190 Outputs high 110 Outputs low 140 Outputs disabled 160 CLK and OC at 4 V, D inputs at 0 V 180 mA † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. ‡ All typical values are at VCC= 5 V, TA = 25°C. § Not more than one output should be shorted at a time and duration of the short circuit should not exceed one second. switching characteristics, VCC = 5 V, TA = 25°C (see Figure 2) PARAMETER FROM (INPUT) TO (OUTPUT) TEST CONDITIONS ’S373 MIN ’S374 MAX RL = 280 Ω, CL = 15 pF, See Note 3 fmax MIN TYP 75 100 MAX Data Any Q RL = 280 Ω, CL = 15 pF,, See Note 3 7 12 7 12 tPLH tPHL C or CLK Any Q RL = 280 Ω, CL = 15 pF,, See Note 3 7 14 8 15 12 18 11 17 tPZH tPZL Any Q RL = 280 Ω, CL = 15 pF,, See Note 3 8 15 8 15 OC 11 18 11 18 tPHZ tPLZ Any Q RL = 280 Ω, CL = 5 pF 6 9 5 9 OC 8 12 7 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT MHz tPLH tPHL NOTE 3. Maximum clock frequency is tested with all outputs loaded. fmax = maximum clock frequency tPLH = propagation delay time, low-to-high-level output tPHL = propagation delay time, high-to-low-level output tPZH = output enable time to high level tPZL = output enable time to low level tPHZ = output disable time from high level tPLZ = output disable time from low level 10 TYP ns ns ns ns SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 PARAMETER MEASUREMENT INFORMATION SERIES 54LS/74LS DEVICES VCC Test Point VCC RL From Output Under Test CL (see Note A) CL (see Note A) High-Level Pulse 1.3 V S2 LOAD CIRCUIT FOR 3-STATE OUTPUTS 3V Timing Input 1.3 V 5 kΩ Test Point LOAD CIRCUIT FOR OPEN-COLLECTOR OUTPUTS LOAD CIRCUIT FOR 2-STATE TOTEM-POLE OUTPUTS S1 (see Note B) CL (see Note A) RL (see Note B) RL From Output Under Test VCC From Output Under Test Test Point 1.3 V 0V tw Low-Level Pulse 1.3 V tsu 0V In-Phase Output (see Note D) 3V 1.3 V 1.3 V 0V tPZL tPLZ tPHL VOH 1.3 V 1.3 V Waveform 1 (see Notes C and D) VOL tPZH tPLH VOH 1.3 V 1.3 V VOL Waveform 2 (see Notes C and D) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES ≈1.5 V 1.3 V VOL tPHL Out-of-Phase Output (see Note D) 1.3 V 0V Output Control (low-level enabling) 1.3 V tPLH 1.3 V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.3 V 3V Data Input 1.3 V VOLTAGE WAVEFORMS PULSE DURATIONS Input th VOL + 0.5 V tPHZ VOH 1.3 V VOH – 0.5 V ≈1.5 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS NOTES: A. CL includes probe and jig capacitance. B. All diodes are 1N3064 or equivalent. C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. D. S1 and S2 are closed for tPLH, tPHL, tPHZ, and tPLZ; S1 is open and S2 is closed for tPZH; S1 is closed and S2 is open for tPZL. E. Phase relationships between inputs and outputs have been chosen arbitrarily for these examples. F. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO ≈ 50 Ω, tr ≤ 1.5 ns, tf ≤ 2.6 ns. G. The outputs are measured one at a time with one input transition per measurement. H. All parameters and waveforms are not applicable to all devices . Figure 1. Load Circuits and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 PARAMETER MEASUREMENT INFORMATION SERIES 54S/74S DEVICES VCC Test Point VCC RL (see Note B) From Output Under Test CL (see Note A) High-Level Pulse 1.5 V S2 LOAD CIRCUIT FOR 3-STATE OUTPUTS 3V Timing Input 1.5 V 1 kΩ Test Point LOAD CIRCUIT FOR OPEN-COLLECTOR OUTPUTS LOAD CIRCUIT FOR 2-STATE TOTEM-POLE OUTPUTS S1 (see Note B) CL (see Note A) RL CL (see Note A) RL From Output Under Test VCC From Output Under Test Test Point 1.5 V 0V tw Low-Level Pulse 1.5 V tsu Data Input 1.5 V VOLTAGE WAVEFORMS PULSE DURATIONS 1.5 V 1.5 V In-Phase Output (see Note D) tPHL VOH 1.5 V Out-of-Phase Output (see Note D) 0V 1.5 V 1.5 V Waveform 1 (see Notes C and D) tPLZ VOH 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES ≈1.5 V 1.5 V VOL tPZH tPLH 1.5 V 0V tPZL VOL tPHL 1.5 V 3V Output Control (low-level enabling) 0V tPLH 3V 1.5 V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V Input th Waveform 2 (see Notes C and D) VOL + 0.5 V tPHZ VOH 1.5 V VOH – 0.5 V ≈1.5 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS NOTES: A. CL includes probe and jig capacitance. B. All diodes are 1N3064 or equivalent. C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. D. S1 and S2 are closed for tPLH, tPHL, tPHZ, and tPLZ; S1 is open and S2 is closed for tPZH; S1 is closed and S2 is open for tPZL. E. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO ≈ 50 Ω; tr and tf ≤ 7 ns for Series 54/74 devices and tr and tf ≤ 2.5 ns for Series 54S/74S devices. F. The outputs are measured one at a time with one input transition per measurement. G. All parameters and waveforms are not applicable to all devices . Figure 2. Load Circuits and Voltage Waveforms 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54LS373, SN54LS374, SN54S373, SN54S374, SN74LS373, SN74LS374, SN74S373, SN74S374 OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS SDLS165B – OCTOBER 1975 – REVISED AUGUST 2002 TYPICAL APPLICATION DATA Bidirectional Bus Driver Output Control 1 1D 2D 3D 4D 5D 6D 7D 8D Bidirectional Data Bus 1 ’LS374 or ’S374 C 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q Bidirectional Data Bus 2 Clock 1 Clock 2 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q C ’LS374 or ’S374 1D 2D 3D 4D 5D 6D 7D 8D Output Control 2 Clock 1 H Clock 2 H Bus Exchange Clock Clock Circuit for Bus Exchange Expandable 4-Word by 8-Bit General Register File ’LS374 or ’S374 1/2 SN74LS139 or SN74S139 G Enable Select A B Y0 Y1 Y2 Y3 ’LS374 or ’S374 ’LS374 or ’S374 ’LS374 or ’S374 1/2 SN74LS139 or SN74S139 Y0 A Y1 B Clock Select POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Y2 Y3 G Clock 13 PACKAGE OPTION ADDENDUM www.ti.com 28-Feb-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type 5962-7801102VRA ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC 5962-7801102VSA ACTIVE CFP W 20 1 None Call TI Level-NC-NC-NC Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) 78011022A ACTIVE LCCC FK 20 1 None Call TI Level-NC-NC-NC 7801102RA ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC 7801102SA ACTIVE CFP W 20 1 None Call TI Level-NC-NC-NC JM38510/32502B2A ACTIVE LCCC FK 20 1 None Call TI Level-NC-NC-NC JM38510/32502BRA ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC JM38510/32502BSA ACTIVE CFP W 20 1 None Call TI Level-NC-NC-NC JM38510/32502SRA ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC JM38510/32502SSA ACTIVE CFP W 20 1 None Call TI Level-NC-NC-NC JM38510/32503B2A ACTIVE LCCC FK 20 1 None Call TI Level-NC-NC-NC JM38510/32503BRA ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC JM38510/32503BSA ACTIVE CFP W 20 1 None Call TI Level-NC-NC-NC SN54LS373J ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC SN54LS374J ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC SN54S373J ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC SN54S374J ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC SN74LS373DW ACTIVE SOIC DW 20 25 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM SN74LS373DWR ACTIVE SOIC DW 20 2000 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM SN74LS373N ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC SN74LS373N3 OBSOLETE PDIP N 20 None Call TI SN74LS373NSR ACTIVE SO NS 20 2000 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM SN74LS374DBR ACTIVE SSOP DB 20 2000 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM SN74LS374DW ACTIVE SOIC DW 20 25 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM SN74LS374DWR ACTIVE SOIC DW 20 2000 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM None Call TI 20 Pb-Free (RoHS) CU NIPDAU SN74LS374J OBSOLETE CDIP J 20 SN74LS374N ACTIVE PDIP N 20 Call TI Call TI Level-NC-NC-NC SN74LS374N3 OBSOLETE PDIP N 20 None Call TI SN74LS374NSR ACTIVE SO NS 20 2000 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM SN74S373DW ACTIVE SOIC DW 20 25 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM SN74S373DWR ACTIVE SOIC DW 20 2000 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM None Call TI 20 Pb-Free (RoHS) CU NIPDAU None Call TI SN74S373J OBSOLETE CDIP J 20 SN74S373N ACTIVE PDIP N 20 SN74S373N3 OBSOLETE PDIP N 20 Addendum-Page 1 Call TI Call TI Level-NC-NC-NC Call TI PACKAGE OPTION ADDENDUM www.ti.com 28-Feb-2005 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN74S374DW ACTIVE SOIC DW 20 25 SN74S374DWR ACTIVE SOIC DW 20 SN74S374J OBSOLETE CDIP J 20 SN74S374N ACTIVE PDIP N 20 Lead/Ball Finish MSL Peak Temp (3) Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM 2000 Pb-Free (RoHS) CU NIPDAU Level-2-250C-1 YEAR/ Level-1-235C-UNLIM None Call TI 20 Pb-Free (RoHS) CU NIPDAU Call TI Level-NC-NC-NC SN74S374N3 OBSOLETE PDIP N 20 None Call TI SN74S374NSR ACTIVE SO NS 20 2000 Pb-Free (RoHS) CU NIPDAU Call TI SNJ54LS373FK ACTIVE LCCC FK 20 1 None Call TI Level-NC-NC-NC SNJ54LS373J ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC SNJ54LS373W ACTIVE CFP W 20 1 None Call TI Level-NC-NC-NC SNJ54LS374FK ACTIVE LCCC FK 20 1 None Call TI Level-NC-NC-NC SNJ54LS374J ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC SNJ54LS374W ACTIVE CFP W 20 1 None Call TI Level-NC-NC-NC SNJ54S373FK ACTIVE LCCC FK 20 1 None Call TI Level-NC-NC-NC SNJ54S373J ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC SNJ54S374FK ACTIVE LCCC FK 20 1 None Call TI Level-NC-NC-NC SNJ54S374J ACTIVE CDIP J 20 1 None Call TI Level-NC-NC-NC SNJ54S374W ACTIVE CFP W 20 1 None Call TI Level-NC-NC-NC Level-2-260C-1 YEAR/ Level-1-235C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated