NJM2717 SINGLE SUPPLY HI-SLEW RATE DUAL OPERATIONAL AMPLIFER ■GENERAL DESCRIPTION The NJM2717 is single supply dual high slew rate operational amplifier. It is applicable to A/D converters, FAX, scanner which require the single supply operation and high slew rate. ■ FEATURES ●Single Supply ●Operating Voltage ●High Slew Rate ●Operating Current ●Output Voltage Range ●Bipolar Technology ●Package Outline 2.7V to 12V 40V/µs Typ. at V+=5V 8mA typ. at V+=5V VOH ≥4.5V Typ. at V+=5V,RL=4kΩ VOL ≤0.05V Typ. at V+=5V,RL=4kΩ ■ PACKAGE OUTLINE NJM2717D NJM2717M NJM2717V NJM2717RB1 DIP8, DMP8, SSOP8, TVSP8 ■ PIN CONFIGRATION 1 8 2 7 3 6 4 5 PIN FUNCTION 1. A OUTPUT 2. A -INPUT 3. A +INPUT 4. GND 5. B +INPUT 6. B –INPUT 7. B OUTPUT + 8. V NJM2717D NJM2717M NJM2717V NJM2717RB1 Ver.2005-01-26 -1- NJM2717 ■ ABSOLUTE MAXIMUM RATINGS PARAMETER Supply Voltage Differential Input Voltage Input Common Mode Voltage Range Power Dissipation Output Sink Current Operating Temperature Range Storage Temperature Range SYMBOL + V VID VICM (Ta=25ûC ) RATINGS 15.0 ± 3 -0.3 to +15.0(Note 1) (DIP8) 500 (DMP8) 300 (SSOP8) 250 (TVSP8) 320 10 -40 to +85 -40 to +125 PD I SI NK Topr Tstg UNIT V V V mW mA ûC ûC (Note 1) For supply voltage less than 15V, the absolute maximum input voltage is equal to the supply voltage. ■ RECOMMENDED OPERATING CONDITION PARAMETER Supply Voltage SYMBOL + V (Ta=25ûC ) TEST CONDITION 2.7 to 12.0 UNIT V ■ ELECTRICAL CHARACTERISTICS ●DC CHARACTERISTICS PARAMETER Operating Current Input Offset Voltage Input Bias Current Input Offset Current Voltage Gain Common Mode Rejection Ratio Supply Voltage Rejection Ratio Output Voltage 1 Output Voltage 2 Output Source Current Output Sink Current Input Common Mode Voltage Range SYMBOL I CC VIO IB IIO AV CMR SVR VOH1 VOL1 VOH2 VOL2 (V+=5V,Ta=25ûC ) TEST CONDITION R L =∞, no signal R S =0Ω R L ≥ 10kΩ, VO=1.5V to 3.5V 0V ≤ V CM ≤ 3.8V + V =4V to 8V R L =4kΩ to GND R L =4kΩ to 2.5V I SOURCE I SI NK VICM MIN TYP MAX UNIT 60 8.0 1 2 0.2 75 11.0 11 4.4 0.5 - mA mV µA µA dB 45 50 4.3 4.5 1 2.5 0 to 3.8 80 85 4.5 0.05 4.7 0.1 2.5 6 - 0.1 0.5 5 dB dB V V V V mA mA V (V+=5V,Ta=25ûC ) ●AC CHARACTERISTICS PARAMETER Unity Gain Bandwidth SYMBOL TEST CONDITION fT MIN TYP MAX UNIT - 20 - MHz (V+=5V,Ta=25ûC ) ●TRANSIENT CHARACTERISTICS PARAMETER Slew Rate -2- SYMBOL SR TEST CONDITION MIN TYP MAX UNIT - 40 - V/µs Ver.2005-01-26 NJM2717 ■ ELECTRICAL CHARACTERISTICS ●DC CHARACTERISTICS PARAMETER SYMBOL Operating Current Input Offset Voltage Input Bias Current Input Offset Current Voltage Gain I CC VIO IB IIO AV Common Mode Rejection Ratio Supply Voltage Rejection Ratio Output Voltage 1 CMR SVR VOH1 VOL1 VOH2 VOL2 Output Voltage 2 Output Source Current Output Sink Current Input Common Mode Voltage Range (V+=12V,Ta=25ûC ) TEST CONDITION R L =∞, no signal R S =0Ω R L ≥ 10kΩ, VO=2V to 10V 0V ≤ V CM ≤ 10.8V + V =8V to 12V R L =10kΩ to GND R L =10kΩ to 6V I SOURCE I SI NK VICM MIN TYP MAX UNIT 60 10.0 1 2.1 0.2 80 14.5 12 4.4 1 - mA mV µA µA dB 45 50 11.3 11.5 1 2.5 0 to 10.8 80 85 11.5 0.1 11.7 0.1 3 8 - 0.3 0.5 - dB dB V V V V mA mA V (V+=12V,Ta=25ûC ) ●AC CHARACTERISTICS PARAMETER Unity Gain Bandwidth SYMBOL TEST CONDITION fT MIN TYP MAX UNIT - 21 - MHz (V+=12V,Ta=25ûC ) ●TRANSIENT CHARACTERISTICS PARAMETER Slew Rate Ver.2005-01-26 SYMBOL SR TEST CONDITION MIN TYP MAX UNIT - 45 - V/µs -3- NJM2717 ■ ELECTRICAL CHARACTERISTICS ●DC CHARACTERISTICS PARAMETER SYMBOL Operating Current Input Offset Voltage Input Bias Current Input Offset Current Voltage Gain I CC VIO IB IIO AV Common Mode Rejection Ratio Supply Voltage Rejection Ratio Output Voltage 1 CMR SVR VOH1 VOL1 VOH2 VOL2 Output Voltage 2 Output Source Current Output Sink Current Input Common Mode Voltage Range (V+=2.7V,Ta=25ûC ) TEST CONDITION R L =∞, no signal R S =0Ω R L ≥ 10kΩ, VO=0.85V to 1.85V 0V ≤ V CM ≤ 1.5V + V =2.7V to 4V R L =4kΩ to GND R L =4kΩ to 1.35V I SOURCE I SI NK VICM MIN TYP MAX UNIT 60 6 1 1.7 0.2 73 8.5 10 4.4 0.5 - mA mV µA µA dB 45 50 2.5 2.6 1 2.5 0 to 1.5 80 75 2.6 0.05 2.65 0.1 2.5 5 - 0.1 0.2 - dB dB V V V V mA mA V (V+=2.7V,Ta=25ûC ) ●AC CHARACTERISTICS PARAMETER Unity Gain Bandwidth SYMBOL TEST CONDITION fT MIN TYP MAX UNIT - 19 - MHz (V+=2.7V,Ta=25ûC ) ●TRANSIENT CHARACTERISTICS PARAMETER Slew Rate -4- SYMBOL SR TEST CONDITION MIN TYP MAX UNIT - 30 - V/µs Ver.2005-01-26 NJM2717 ■ Typical Characteristics Operating Current vs. Supply Voltage Operating Current vs. Ambient temperature (Ambient Temperature) 20 20 18 Ta=+85oC 16 o Ta=+125 C Operating Current [mA] Operating Current [mA] 18 14 12 Ta=+25oC 10 8 6 Ta=-40oC 4 o Ta=-50 C 2 16 14 V+/V-=±6.0V V+/V-=±2.5V 12 10 8 6 V+/V-=±1.35V 4 2 0 0 0 2 4 6 8 10 12 Supply Voltage V+ [V] 14 16 -50 Input Offset Voltage vs. Supply Voltage 0 25 50 75 100 Ambien t Temperature [oC] 125 Input Offset Voltage vs. Ambient Tmperature (Ambient Temperature) 5 3 Ta=-50oC 2 4 o Ta=-40 C 1 Input Offset Voltage [mV] Input Offset Voltage [mV] -25 0 -1 Ta=+25oC -2 -3 Ta=+85oC -4 Ta=+125oC -5 -6 3 2 1 V+/V-=±2.5V 0 -1 -2 V+/V-=±1.35V -3 V+/V-=±6.0V -4 -7 -5 0 Ver.2005-01-26 2 4 6 8 10 12 Supply voltage V+ [V] 14 16 -50 -25 0 25 50 75 100 125 Ambient Temperature [oC] -5- NJM2717 ■ Typical Characteristics Input Offset Voltage vs. Input Common Mode Vltage Input Offset Voltage vs. Input Common Mode Voltage (Ambient Temperature) (Ambient Temperature) V+/V-=±1.35V 4 4 3 3 2 1 o Ta=-40 C 0 -1 -2 Ta=+85oC -3 Ta=+25oC -4 0 0.5 1 1.5 Input Common Mode Voltage [V] 0 -1 -2 Ta=+85oC Ta=+25oC -3 -5 -0.5 2 0.5 1.5 2.5 3.5 Input Common Mode Voltage [V] Input Bias Current vs. Input Common Mode Voltage (Ambient Temperature) (Ambient Temperature) V+/V-=±6.0V 4 6 3 5 2 Ta=-40oC 1 0 -1 -2 o -3 Ta=+85 C Ta=+25oC -4 4.5 V+/V-=±1.35V 7 Input Bias Current [uA] Input Offset Voltage [mV] Ta=-40oC 1 Input Offset Voltage vs. Input Common Mode Voltage Range 5 4 Ta=-40oC 3 2 1 0 Ta=+85oC -1 Ta=+25oC -2 -5 -1 -3 -0.5 1 3 5 7 9 11 Input Common Mode Voltage [V] Input Bias Current vs. Input Common Mode Voltage (Ambient Temperature) (Ambient Temperature) V+/V-=±6.0V V+/V-=±2.5V Input Bias Current [uA] 6 5 Ta=-40oC 4 3 2 1 o Ta=+85 C o Ta=+25 C -1 -2 -3 -0.5 2 7 6 0 0 0.5 1 1.5 Input Common Mode Voltage [V] Input Bias Current vs. Input Common Mode Voltage 7 Input Bias Current [uA] 2 -4 -5 -0.5 -6- V+/V-=±2.5V 5 Input Offset Voltage [mV] Input Offset Voltage [mV] 5 5 Ta=-40oC 4 3 2 1 0 Ta=+85oC Ta=+25oC -1 -2 -3 0.5 1.5 2.5 3.5 Input Common Mode Voltage [V] 4.5 -1 1 3 5 7 9 11 Input Common Mode Voltage [V] Ver.2005-01-26 NJM2717 ■ Typical Characteristics Maximum Output Voltage vs. Supply Voltage 8 V+/V-=±6.0V 6 4 Ta=- 50oC Ta=- 40oC Ta=+ 25oC Ta=+ 85oC Ta=+125oC 2 0 -2 -4 -6 -8 2 4 6 Supply Voltage V+/V- [V] V+/V-=±2.5V 2 0 V+/V-=±1.35V -2 -4 8 -50 (Supply Voltage) (Ambient Temperature) V+/V-=±1.35V, GV=OPEN - 3.0 125 V+/V-=±2.5V 2.0 V+/V-=±1.35V 0.0 -2.0 -4.0 -VOM Maximum Output Voltage [V] +VOM V /V =±6.0V 4.0 0 25 50 75 100 Ambient Temperature [oC] Maximum Output Voltage vs. Load Resistance V+/V-,GV=OPEN,Ta=+25oC + -25 Maximum Output Voltage vs. Load Resistance 6.0 Maximum Output Voltage [V] 4 -6 0 -6.0 2.0 +VOM 1.0 Ta=-40oC Ta=+25oC Ta=+85oC 0.0 -1.0 -VOM -2.0 -3.0 3.0 1.0 10.0 Load Resistance [kΩ] 100.0 1.0 10.0 Load Resistance [kΩ] Maximum Output Voltage vs. Load Resistance Maximum Output vltage vs. Load Resistance (Ambient Temperautre) V+/V-=±2.5V, GV=OPEN (Ambient Temperature) 2.0 Ta=-40oC Ta=+25oC Ta=+85oC 0.0 -1.0 -VOM -2.0 -3.0 100.0 V+/V-=±6.0V, GV=OPEN 6.0 +VOM 1.0 0.1 Maximum Output Voltage [V] 0.1 Maximum Output Voltage [V] GV=OPEN,RL=4KΩ 6 Maximum Output Voltage [V] Maximum Output Voltage [V] Maximum Output Voltage vs. Ambient Temperature (Ambient Temperature) GV=OPEN,RL=4kΩ +VOM 4.0 Ta=-40oC Ta=+25oC Ta=+85oC 2.0 0.0 -2.0 -4.0 -VOM -6.0 0.1 Ver.2005-01-26 1.0 10.0 Load Resistance [kΩ] 100.0 0.1 1.0 10.0 Load Resistance [kΩ] 100.0 -7- NJM2717 ■ Typical Characteristics Maximum Output Voltage vs. Load Resistance Maximum Output Voltage vs. Load Resistance (Ambient Temperature) 5.0 +VOM 4.0 3.0 2.0 V+=+2.7V, V-=GND,GV=OPEN 0.50 Maximum Output Voltage [V] Maximum Output Voltage [V] (Ambient Temperature) V+=+2.7V,V-=GND,GV=OPEN Ta=+85oC Ta=+25oC Ta=-40oC 1.0 -VOM 0.0 0.40 0.30 Ta=+85oC 0.20 o Ta=+25 C Ta=-40oC -VOM 0.10 0.00 0.1 1 10 Load Resistance [kΩ] 100 0.1 Maximum Output Voltage vs. Load Resistance (Ambient Temperarture) (Ambient Temperature) V+=+5.0V, V-=GND,GV=OPEN V+=+5.0V, V-=GND, GV=OPEN 0.50 +VOM 4.0 Ta=+85oC Ta=+25oC Ta=-40oC 3.0 2.0 1.0 -VOM 0.0 0.40 0.30 Ta=+85oC 0.20 o Ta=+25 C Ta=-40oC 1 10 Load Resistance [kΩ] 100 0.1 Maximum Output Voltage vs. Load Resistance +VOM 8.0 Ta=+85oC Ta=+25oC Ta=-40oC 6.0 4.0 2.0 100 (Ambient Temperature) V+=+12.0V, V-=GND, GV=OPEN 0.50 Maximum Output Voltage [V] 10.0 1 10 Load Resistance [kΩ] Maximum Output Voltage vs. Load Resistance (Ambient temperature) V+=+12.0V,V-=GND, GV=OPEN 12.0 Maximum Output Voltage [V] -VOM 0.10 0.00 0.1 -VOM 0.40 0.30 Ta=+85oC Ta=+25oC 0.20 Ta=-40oC 0.10 -VOM 0.00 0.0 0.1 -8- 100 Maximum Output Voltage vs. Load Resistance Maximum Output Voltage [V] Maximum Output Voltage [V] 5.0 1 10 Load Resistance [kΩ] 1 10 Load Resistance [kΩ] 100 0.1 1 10 Load Resistance [kΩ] 100 Ver.2005-01-26 NJM2717 ■ Typical Characteristics Maximum Output Voltage vs. Output Source Current Maximum Output Voltage vs. Output Sink Current V+/V-=±1.35V,GV=OPEN 0.0 2.5 -0.5 Maximum Output Voltage [V] Maximum Output Voltage [V] V+/V-=±1.35V,GV=OPEN 3.0 2.0 1.5 1.0 Ta=-40oC Ta=+25oC Ta=+85oC 0.5 -1.0 -1.5 Ta=-40oC Ta=+25oC Ta=+85oC -2.0 -2.5 -3.0 0.0 0.01 0.1 1 Output Source Current [mA] 0.01 10 Maximum Output Voltage vs. Output Source Current V+/V-=±2.5V,GV=OPEN 0.0 2.5 -0.5 Maximum Output Voltage [V] Maximum Output Voltage [V] V+/V-=±2.5V,GV=OPEN 2.0 1.5 Ta=-40oC Ta=+25oC Ta=+85oC 0.5 0.0 -1.0 Ta=-40oC Ta=+25oC Ta=+85oC -1.5 -2.0 -2.5 -3.0 0.01 0.1 1 Output Source Current [mA] 10 0.01 Maximum Output Voltage vs. Output Source Current 100 V+/V-=±6.0V,GV=OPEN 0.0 5.0 -1.0 Maximum Output Voltage [V] 6.0 4.0 Ta=-40oC Ta=+25oC Ta=+85oC 3.0 0.1 1 10 Output Sink Current [mA] Maximum Output Voltage vs. Output Sink Current V+/V-=±6.0V,GV=OPEN Maximum Output Voltage [V] 100 Maximum Output Voltage vs. Output Sink Current 3.0 1.0 0.1 1 10 Output Sink Current [mA] 2.0 1.0 0.0 -2.0 -3.0 Ta=-40oC Ta=+25oC Ta=+85oC -4.0 -5.0 -6.0 0.01 Ver.2005-01-26 0.1 1 Output Source Current [mA] 10 0.01 0.1 1 10 Output Sink Current [mA] 100 -9- NJM2717 ■ Typical Characteristics Voltage Gain vs. Frequency Voltage Gain/Phase vs. Frequency (Voltage Follower) V+/V-,GV=0dB, RL=2kΩ to GND, Ta=25oC GV=40dB, RL=2kΩ to GND, CL=10pF, Ta=25oC 50 45 0 20 -45 -90 + - V /V =±1.35V 10 -135 0.01 10 -180 100 CL=10pF -4 V+/V-=±1.35V V+/V-=±2.5V V+/V-=±6.0V 0.1 1 10 100 Frequency [MHz] 1000 Pulse Response Pulse Response V+/V-=±2.5V,AV=0dB,f=1MHz,VIN=±1V, RL=10KΩ,Ta=25oC RL=10KΩ,Ta=25oC 1.0 1.5 -0.5 0.5 CL=100pF 0.0 -1.0 CL=10pF -0.5 OUTPUT -2.0 -400 -200 0 200 Time [nsec] 400 Input Voltage [V] 1.0 Output Voltage [V] CL=220pF 0.0 2.5 1.5 2.0 0.5 Input Voltage [V] -2 -10 INPUT -600 0 V+/V-=±1.35V,AV=0dB,f=1MHz,VIN=±0.5V, 1.0 -1.5 CL=100pF -8 0.1 1 Frequency [MHz] V+/V-=±1.35V V+/V-=±2.5V V+/V-=±6.0V 2 -6 V+/V-=±2.5V 0 0.001 4 INPUT 0.5 1.5 0.0 1.0 -0.5 CL=220pF CL=100pF -1.0 CL=10pF -1.5 -2.0 -1.0 600 2.0 -2.5 -400 0.0 -0.5 -1.0 OUTPUT -600 0.5 Output Voltagve [V] V+/V-=±6.0V Voltage Gain [dB] Phase 30 6 Phase [deg] Voltage Gain [dB] 8 Gain 40 10 -200 0 200 Time [nsec] 400 -1.5 600 Pulse Response V+/V-=±6.0V,AV=0dB,f=1MHz, VIN=±1V,RL=10KΩ,Ta=25oC 1.5 2.5 1.0 2.0 0.5 1.5 0.0 1.0 -0.5 CL=220pF CL=100pF -1.0 CL=10pF -1.5 -2.0 -2.5 - 10 - -400 0.0 -0.5 -1.0 OUTPUT -600 0.5 -200 0 200 Time [nsec] 400 -1.5 600 Output Voltage [V] Input Voltage [V] INPUT [CAUTION] The specifications on this data book are only given for information, without any guarantee as regards either mistakes or omissions. The application circuits in this data book are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. Ver.2005-01-26