MC33063A MC34063A www.ti.com SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 1.5-A PEAK BOOST/BUCK/INVERTING SWITCHING REGULATORS Check for Samples: MC33063A MC34063A FEATURES 1 • • • • Wide Input Voltage Range: 3 V to 40 V High Output Switch Current: Up to 1.5 A Adjustable Output Voltage Oscillator Frequency Up to 100 kHz • • • Precision Internal Reference: 2% Short-Circuit Current Limiting Low Standby Current D (SOIC) OR P (PDIP) PACKAGE (TOP VIEW) Switch Collector Switch Emitter Timing Capacitor GND 1 8 2 7 3 6 4 5 Driver Collector Ipk VCC Comparator Inverting Input DRJ (QFN) PACKAGE (TOP VIEW) Switch Collector 1 Switch Emitter † 8 Driver Collector 2 7 Ipk Timing Capacitor 3 6 VCC GND 4 5 Comparator Inverting Input † The exposed thermal pad is electrically bonded internally to pin 4 (GND) . DESCRIPTION/ORDERING INFORMATION The MC33063A and MC34063A are easy-to-use ICs containing all the primary circuitry needed for building simple dc-dc converters. These devices primarily consist of an internal temperature-compensated reference, a comparator, an oscillator, a PWM controller with active current limiting, a driver, and a high-current output switch. Thus, the devices require minimal external components to build converters in the boost, buck, and inverting topologies. The MC33063A is characterized for operation from –40°C to 85°C, while the MC34063A is characterized for operation from 0°C to 70°C. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2004–2009, Texas Instruments Incorporated MC33063A MC34063A SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 www.ti.com ORDERING INFORMATION (1) PACKAGE (2) TA –40°C to 85°C MC33063AP MC33063AP QFN – DRJ Reel of 1000 MC33063ADRJR ZYF Tube of 75 MC33063AD Reel of 2500 MC33063ADR PDIP – P Tube of 50 MC34063AP MC34063AP QFN – DRJ Reel of 1000 MC34063ADRJR ZYG Tube of 75 MC34063AD Reel of 2500 MC34063ADR SOIC – D (1) (2) TOP-SIDE MARKING Tube of 50 SOIC – D 0°C to 70°C ORDERABLE PART NUMBER PDIP – P M33063A M34063A For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. FUNCTIONAL BLOCK DIAGRAM Drive Collector 8 1 Switch Collector 2 Switch Emitter 3 Timing Capacitor Q2 S Q Q1 R 100 Ω Ipk Sense 7 Ipk Oscillator CT 6 VCC + − Comparator Inverting Input 2 1.25-V Reference Regulator 4 5 Submit Documentation Feedback GND Copyright © 2004–2009, Texas Instruments Incorporated Product Folder Link(s): MC33063A MC34063A MC33063A MC34063A www.ti.com SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN VCC Supply voltage VIR Comparator Inverting Input voltage range VC(switch) Switch Collector voltage VE(switch) Switch Emitter voltage VCE(switch) Switch Collector to Switch Emitter voltage VC(driver) MAX UNIT 40 V 40 V 40 V 40 V 40 V Driver Collector voltage 40 V IC(driver) Driver Collector current 100 mA ISW Switch current 1.5 A Package thermal impedance (2) θJA VPIN1 = 40 V (3) TJ Operating virtual junction temperature Tstg Storage temperature range (1) (2) (3) –0.3 D package 97 DRJ package 41 P package 85 –65 °C/W 150 °C 150 °C Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions VCC TA MIN MAX 3 40 MC33063A –40 85 MC34063A 0 70 Supply voltage Operating free-air temperature UNIT V °C Electrical Characteristics VCC = 5 V, TA = full operating range (unless otherwise noted) (see block diagram) Oscillator MIN TYP MAX fosc Oscillator frequency PARAMETER VPIN5 = 0 V, CT = 1 nF TEST CONDITIONS 25°C TA 24 33 42 kHz Ichg Charge current VCC = 5 V to 40 V 25°C 24 35 42 μA Idischg Discharge current VCC = 5 V to 40 V 25°C 140 220 260 μA Idischg/Ichg Discharge-to-charge current ratio VPIN7 = VCC 25°C 5.2 6.5 7.5 VIpk Current-limit sense voltage Idischg = Ichg 25°C 250 300 350 Copyright © 2004–2009, Texas Instruments Incorporated Product Folder Link(s): MC33063A MC34063A Submit Documentation Feedback UNIT mV 3 MC33063A MC34063A SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 www.ti.com Output Switch (1) PARAMETER TEST CONDITIONS VCE(sat) Saturation voltage – Darlington connection ISW = 1 A, pins 1 and 8 connected VCE(sat) Saturation voltage – non-Darlington connection (2) ISW = 1 A, RPIN8 = 82 Ω to VCC, forced β ~ 20 hFE DC current gain ISW = 1 A, VCE = 5 V IC(off) Collector off-state current VCE = 40 V (1) (2) TA MIN TYP MAX Full range 1 1.3 V Full range 0.45 0.7 V 100 μA 25°C 50 Full range UNIT 75 0.01 Low duty-cycle pulse testing is used to maintain junction temperature as close to ambient temperature as possible. In the non-Darlington configuration, if the output switch is driven into hard saturation at low switch currents (≤300 mA) and high driver currents (≥30 mA), it may take up to 2 μs for the switch to come out of saturation. This condition effectively shortens the off time at frequencies ≥30 kHz, becoming magnified as temperature increases. The following output drive condition is recommended in the non-Darlington configuration: Forced β of output switch = IC,SW / (IC,driver – 7 mA) ≥ 10, where ~7 mA is required by the 100-Ω resistor in the emitter of the driver to forward bias the Vbe of the switch. Comparator PARAMETER TEST CONDITIONS TA MIN TYP MAX 25°C 1.225 1.25 1.275 Full range 1.21 UNIT Vth Threshold voltage ΔVth Threshold-voltage line regulation VCC = 5 V to 40 V Full range 1.4 5 mV IIB Input bias current VIN = 0 V Full range –20 –400 nA MIN MAX UNIT 1.29 V Total Device PARAMETER ICC 4 Supply current Submit Documentation Feedback TEST CONDITIONS TA VCC = 5 V to 40 V, CT = 1 nF, VPIN7 = VCC, VPIN5 > Vth, VPIN2 = GND, All other pins open Full range 4 mA Copyright © 2004–2009, Texas Instruments Incorporated Product Folder Link(s): MC33063A MC34063A MC33063A MC34063A www.ti.com SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 TYPICAL CHARACTERISTICS 1000 1.8 100 Pin 7 = VCC Pin 5 = GND TA = 25°C VCE(SAT), Output Switch Saturation Voltage (V) On-Off Time (µs) t ON-OFF, Output Switch VCC = 5 V t ON 10 t OFF 1 0.01 1.7 1.6 1.5 1.4 1.3 1.2 1.1 1.0 1 0 0.0 0.1 1 CT, Oscillator Timing Capacitor (nF) 0.4 0.6 380 340 1.0 Force Beta = 20 0.8 0.6 0.0 0 0 0.0 VCC = 5 V Pin 7 = VCC Pin 2, 3, 5 = GND TA = 25°C 0.2 1 0.4 0.6 0.8 1.0 1.2 IC, Collector Current (A) 1.2 1.4 1.6 VCC = 5 V ICHG = IDISCHG 360 1.2 0.2 1 1.0 Figure 2. Output Switch Saturation Voltage vs Emitter Current (Emitter-Follower Configuration) Darlington Connection 0.4 0.8 IE, Emitter Current (A) VIPK, Current Limit Sense Voltage (mV) VCE(SAT), Output Switch Saturation Voltage (V) 0.2 10 Figure 1. Output Switch On-Off Time vs Oscillator Timing Capacitor 1.4 VCC = 5 V Pin 1, 7, 8 = VCC Pin 3, 5 = GND TA = 25°C 1.4 Figure 3. Output Switch Saturation Voltage vs Collector Current (Common-Emitter Configuration) 1.6 320 300 280 260 240 220 200 −50 −25 0 25 50 75 100 TA, Ambient Temperature (°C) 125 Figure 4. Current-Limit Sense Voltage vs Temperature ICC, Supply Current (mA) 3.6 3.2 2.8 2.4 2.0 1.6 CT = 1 nF Pin 7 = VCC Pin 2 = GND TA = 25°C 1.2 0.8 0.4 0.0 0 5 10 15 20 25 30 35 40 VCC, Supply Voltage (V) Figure 5. Standby Supply Current vs Supply Voltage Copyright © 2004–2009, Texas Instruments Incorporated Product Folder Link(s): MC33063A MC34063A Submit Documentation Feedback 5 MC33063A MC34063A SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 www.ti.com TYPICAL CHARACTERISTICS (continued) 170 µH L 1 8 180 Ω S Q Q2 1N5819 Q1 R 2 7 Ipk RSC 0.22 Ω VIN 12 V 6 + 3 CT VCC + _ Comparator 100 µF 1.25-V Reference Regulator CT 1500 pF 4 5 1.0 µH R2 R1 2.2 kΩ 47 kΩ CO 330 µF VOUT + 1.25 (1 ) R2) R1 VOUT 28 V/175 mA + 100 µF + Optional Filter Figure 6. Step-Up Converter TEST CONDITIONS RESULTS Line regulation VIN = 8 V to 16 V, IO = 175 mA 30 mV ± 0.05% Load regulation VIN = 12 V, IO = 75 mA to 175 mA 10 mV ± 0.017% Output ripple VIN = 12 V, IO = 175 mA 400 mVPP Efficiency VIN = 12 V, IO = 175 mA 87.7% Output ripple with optional filter VIN = 12 V, IO = 175 mA 40 mVPP 6 Submit Documentation Feedback Copyright © 2004–2009, Texas Instruments Incorporated Product Folder Link(s): MC33063A MC34063A MC33063A MC34063A www.ti.com SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 R* 8 1 7 1 7 2 VOUT 2 RSC RSC 6 VIN 8 VOUT VIN 6 * R " 0 for constant Vin a) EXTERNAL npn SWITCH A. b) EXTERNAL pnp SATURATED SWITCH (see Note A) If the output switch is driven into hard saturation (non-Darlington configuration) at low switch currents (≤300 mA) and high driver currents (≥30 mA), it may take up to 2 μs to come out of saturation. This condition will shorten the off time at frequencies ≥30 kHz and is magnified at high temperatures. This condition does not occur with a Darlington configuration because the output switch cannot saturate. If a non-Darlington configuration is used, the output drive configuration in Figure 7b is recommended. Figure 7. External Current-Boost Connections for IC Peak Greater Than 1.5 A Copyright © 2004–2009, Texas Instruments Incorporated Product Folder Link(s): MC33063A MC34063A Submit Documentation Feedback 7 MC33063A MC34063A SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 www.ti.com 1 8 S Q Q2 Q1 R 2 7 VIN 25 V Oscillator 6 + 1N5819 Ipk RSC 0.33 Ω CT 3 VCC + _ Comparator 100 µF L 220 µH CT 470 pF 1.25-V Reference Regulator 4 5 1.0 µH R2 VOUT 5 V/500 mA 3.8 kΩ R1 1.2 kΩ CO 470 µF + VOUT + 1.25 (1 ) R2) R1 + 100 µF Optional Filter Figure 8. Step-Down Converter TEST CONDITIONS RESULTS Line regulation VIN = 15 V to 25 V, IO = 500 mA 12 mV ± 0.12% Load regulation VIN = 25 V, IO = 50 mA to 500 mA 3 mV ± 0.03% Output ripple VIN = 25 V, IO = 500 mA 120 mVPP Short-circuit current VIN = 25 V, RL = 0.1 Ω 1.1 A Efficiency VIN = 25 V, IO = 500 mA 83.7% Output ripple with optional filter VIN = 25 V, IO = 500 mA 40 mVPP 8 1 1 8 7 VIN 7 2 VOUT RSC VOUT 2 RSC 6 VIN a) EXTERNAL npn SWITCH 6 b) EXTERNAL pnp SATURATED SWITCH Figure 9. External Current-Boost Connections for IC Peak Greater Than 1.5 A 8 Submit Documentation Feedback Copyright © 2004–2009, Texas Instruments Incorporated Product Folder Link(s): MC33063A MC34063A MC33063A MC34063A www.ti.com SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 1 8 S Q Q2 Q1 R 2 7 Oscillator 6 VIN 4.5 V to 6.0 V + L 88 µH Ipk RSC 0.24 Ω CT 3 VCC + _ Comparator 100 µF 1.25-V Reference Regulator 1N5819 + 1500 pF 4 5 1.0 µH R1 R2 8.2 kΩ VOUT −12 V/100 mA 953 Ω CO 1000 µF VOUT + *1.25 (1 ) R2) R1 100 µF + + Optional Filter Figure 10. Voltage-Inverting Converter TEST CONDITIONS RESULTS Line regulation VIN = 4.5 V to 6 V, IO = 100 mA 3 mV ± 0.12% Load regulation VIN = 5 V, IO = 10 mA to 100 mA 0.022 V ± 0.09% Output ripple VIN = 5 V, IO = 100 mA 500 mVPP Short-circuit current VIN = 5 V, RL = 0.1 Ω 910 mA Efficiency VIN = 5 V, IO = 100 mA 62.2% Output ripple with optional filter VIN = 5 V, IO = 100 mA 70 mVPP 8 8 1 1 VOUT 7 2 7 2 6 3 5 4 VOUT VIN 6 3 5 4 VIN a) External NPN Switch b) External PNP Saturated Switch Figure 11. External Current-Boost Connections for IC Peak Greater Than 1.5 A Copyright © 2004–2009, Texas Instruments Incorporated Product Folder Link(s): MC33063A MC34063A Submit Documentation Feedback 9 MC33063A MC34063A SLLS636L – DECEMBER 2004 – REVISED DECEMBER 2009 www.ti.com APPLICATION INFORMATION CALCULATION ton/toff STEP UP STEP DOWN VOLTAGE INVERTING Vout ) VF * Vin(min) Vin(min) * Vsat Vout ) VF Vin(min) * Vsat * Vout ŤVoutŤ ) VF Vin * Vsat 1 f 1 f 1 f ton ) toff ton ) toff ton ) toff (ton + toff) t on t off toff ǒton ton ) 1 ) toffǓ * toff 10*5 CT 4 Ipk(switch) 2Iout(max) ǒ CO Vout ǒton ton 4 Ǔ t on )1 t off ǒ 9 ) toffǓ * toff 10*5 ǒton ton Ǔ t on(max) ǒ 4 ǒ Ǔ t on(max) ǒ 1.25(1 ) R2) R1 See Figure 8 Ǔ ǒVin(min) * VsatǓ Ipk(switch) 9 8Vripple(pp) 1.25(1 ) R2) R1 See Figure 6 Ǔ t on )1 t off 0.3 Ipk(switch) Ipk(switch)ǒt on ) t offǓ I outton Vripple(pp) 10*5 ton 2Iout(max) ǒVin(min) * Vsat * VoutǓ Ipk(switch) ) 1 ) toffǓ * toff 0.3 Ipk(switch) ǒVin(min) * VsatǓ Ipk(switch) t on t off ) 1 2Iout(max) 0.3 Ipk(switch) RSC L(min) t on t off t on(max) I outton Vripple(pp) *1.25(1 ) R2) R1 See Figure 10 Vsat = Saturation voltage of the output switch VF = Forward voltage drop of the chosen output rectifier The following power-supply parameters are set by the user: Vin = Nominal input voltage Vout = Desired output voltage Iout = Desired output current fmin = Minimum desired output switching frequency at the selected values of Vin and Iout Vripple = Desired peak-to-peak output ripple voltage. The ripple voltage directly affects the line and load regulation and, thus, must be considered. In practice, the actual capacitor value should be larger than the calculated value, to account for the capacitor's equivalent series resistance and board layout. 10 Submit Documentation Feedback Copyright © 2004–2009, Texas Instruments Incorporated Product Folder Link(s): MC33063A MC34063A PACKAGE OPTION ADDENDUM www.ti.com 1-Jul-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty MC33063AD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC33063ADE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC33063ADG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC33063ADR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC33063ADRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC33063ADRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC33063ADRJR ACTIVE SON DRJ 8 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR MC33063ADRJRG4 ACTIVE SON DRJ 8 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR MC33063AP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type MC33063APE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type MC34063AD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC34063ADE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC34063ADG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC34063ADR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC34063ADRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC34063ADRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM MC34063ADRJR ACTIVE SON DRJ 8 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR MC34063ADRJRG4 ACTIVE SON DRJ 8 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR MC34063AP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type MC34063APE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 1-Jul-2009 TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF MC33063A : • Automotive: MC33063A-Q1 NOTE: Qualified Version Definitions: • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 2-Sep-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device MC33063ADR Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 MC33063ADRJR SON DRJ 8 1000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 MC34063ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 MC34063ADRJR SON DRJ 8 1000 180.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 2-Sep-2009 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) MC33063ADR SOIC D 8 2500 340.5 338.1 20.6 MC33063ADRJR SON DRJ 8 1000 346.0 346.0 29.0 MC34063ADR SOIC D 8 2500 340.5 338.1 20.6 MC34063ADRJR SON DRJ 8 1000 190.5 212.7 31.8 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated