ISL6622 ® Data Sheet October 30, 2008 VR11.1 Compatible Synchronous Rectified Buck MOSFET Drivers Features • Dual MOSFET Drives for Synchronous Rectified Bridge The ISL6622 is a high frequency MOSFET driver designed to drive upper and lower power N-Channel MOSFETs in a synchronous rectified buck converter topology. The advanced PWM protocol of ISL6622 is specifically designed to work with Intersil VR11.1 controllers and combined with N-Channel MOSFETs, form a complete core-voltage regulator solution for advanced microprocessors. When ISL6622 detects a PSI protocol sent by an Intersil VR11.1 controller, it activates Diode Emulation (DE) and Gate Voltage Optimization Technology (GVOT) operation; otherwise, it operates in normal Continuous Conduction Mode (CCM) PWM mode. In the 8 Ld SOIC package, the ISL6622 drives the upper and lower gates to VCC during normal PWM mode, while the lower gate drops down to a fixed 5.75V (typically) during PSI mode. The 10 Ld DFN part offers more flexibility: the upper gate can be driven from 5V to 12V via the UVCC pin, while the lower gate has a resistor-selectable drive voltage of 5.75V, 6.75V, and 7.75V (typically) during PSI mode. This provides the flexibility necessary to optimize applications involving trade-offs between gate charge and conduction losses. To further enhance light load efficiency, the ISL6622 enables diode emulation operation during PSI mode. This allows Discontinuous Conduction Mode (DCM) by detecting when the inductor current reaches zero and subsequently turning off the low side MOSFET to prevent it from sinking current. An advanced adaptive shoot-through protection is integrated to prevent both the upper and lower MOSFETs from conducting simultaneously and to minimize dead time. The ISL6622 has a 20kΩ integrated high-side gate-to-source resistor to prevent self turn-on due to high input bus dV/dt. This driver also has an overvoltage protection feature operational while VCC is below the POR threshold: the PHASE node is connected to the gate of the low side MOSFET (LGATE) via a 10kΩ resistor, limiting the output voltage of the converter close to the gate threshold of the low side MOSFET, dependent on the current being shunted, which provides some protection to the load should the upper MOSFET(s) become shorted. 1 FN6470.2 • Advanced Adaptive Zero Shoot-through Protection • Integrated LDO for Selectable Lower Gate Drive Voltage (5.75V, 6.75V, 7.75V) to Optimize Light Load Efficiency • 36V Internal Bootstrap Diode • Advanced PWM Protocol (Patent Pending) to Support PSI Mode, Diode Emulation, Three-State Operation • Diode Emulation for Enhanced Light Load Efficiency • Bootstrap Capacitor Overcharging Prevention • Supports High Switching Frequency - 3A Sinking Current Capability - Fast Rise/Fall Times and Low Propagation Delays • Integrated High-Side Gate-to-Source Resistor to Prevent from Self Turn-On due to High Input Bus dV/dt • Pre-POR Overvoltage Protection for Start-up and Shutdown • Power Rails Undervoltage Protection • Expandable Bottom Copper Pad for Enhanced Heat Sinking • Dual Flat No-Lead (DFN) Package - Near Chip-Scale Package Footprint; Improves PCB Efficiency and Thinner in Profile • Pb-Free (RoHS Compliant) Applications • High Light Load Efficiency Voltage Regulators • Core Regulators for Advanced Microprocessors • High Current DC/DC Converters • High Frequency and High Efficiency VRM and VRD Related Literature • Technical Brief TB363 “Guidelines for Handling and Processing Moisture Sensitive Surface Mount Devices (SMDs)” • Technical Brief TB417 “Designing Stable Compensation Networks for Single Phase Voltage Mode Buck Regulators” for Power Train Design, Layout Guidelines, and Feedback Compensation Design CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2008. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL6622 Ordering Information PART NUMBER (Note) PART MARKING TEMP. RANGE (°C) PACKAGE (Pb-Free) PKG. DWG. # ISL6622CBZ* 6622 CBZ 0 to +70 8 Ld SOIC M8.15 ISL6622CRZ* 622Z 0 to +70 10 Ld 3x3 DFN L10.3x3 ISL6622IBZ* 6622IBZ -40 to +85 8 Ld SOIC M8.15 ISL6622IRZ* 622I -40 to +85 10 Ld 3x3 DFN L10.3x3 *Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.. Pinouts ISL6622 (10 LD 3x3 DFN) TOP VIEW ISL6622 (8 LD SOIC) TOP VIEW UGATE 1 8 PHASE BOOT 2 7 VCC PWM 3 6 LVCC GND 4 5 UGATE 1 10 PHASE BOOT 2 GD_SEL 3 LGATE 9 VCC 8 UVCC PWM 4 7 LVCC GND 5 6 LGATE GND Block Diagrams ISL6622 BOOT UVCC UGATE LDO GD_SEL 20k VCC PHASE +5V LVCC 11.2k SHOOTTHROUGH PROTECTION 10k LVCC POR/ PWM CONTROL 9.6k LOGIC LGATE GND UVCC = VCC FOR SOIC LVCC = 5.75V (TYPICALLY) @ 50mA FOR SOIC 2 FN6470.2 October 30, 2008 ISL6622 Typical Application Circuit +12V VIN BOOT LVCC +5V VCC UGATE PHASE ISL6622 DRIVER LGATE FB COMP VCC DAC GND PWM REF VDIFF VSEN PWM1 RGND VTT EN_VTT VIN +12V ISEN1- BOOT PVCC ISEN1+ VR_RDY VCC UGATE VID7 PHASE ISL6334 VID6 ISL6612 DRIVER VID5 LGATE VID4 PWM2 VID3 VID2 GND PWM ISEN2- VID1 ISEN2+ VID0 VIN +12V PSI PVCC PWM3 VR_FAN BOOT µP LOAD ISEN3- VR_HOT ISEN3+ VCC UGATE VIN PHASE ISL6612 DRIVER EN_PWR LGATE GND PWM GND PWM4 IMON ISEN4ISEN4+ TCOMP VIN +12V TM OFS FS BOOT SS PVCC +5V +5V VCC UGATE PHASE ISL6612 DRIVER NTC LGATE PWM 3 GND FN6470.2 October 30, 2008 ISL6622 Absolute Maximum Ratings Thermal Information Supply Voltage (VCC, UVCC) . . . . . . . . . . . . . . . . . . . . . . . . . . .15V BOOT Voltage (VBOOT-GND). . . . . . . . . . . . . . . . . . . . . . . . . . . .36V Input Voltage (VPWM) . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to 7V UGATE. . . . . . . . . . . . . . . . . . . VPHASE - 0.3VDC to VBOOT + 0.3V VPHASE - 3.5V (<100ns Pulse Width, 2µJ) to VBOOT + 0.3V LGATE . . . . . . . . . . . . . . . . . . . . . . .GND - 0.3VDC to VLVCC + 0.3V GND - 5V (<100ns Pulse Width, 2µJ) to VLVCC + 0.3V PHASE. . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3VDC to 15VDC GND - 8V (<200ns, 10µJ) to 30V (<200ns, VBOOT-GND<36V) Thermal Resistance θJA (°C/W) θJC (°C/W) SOIC Package (Note 1) . . . . . . . . . . . . 100 N/A DFN Package (Notes 2, 3) . . . . . . . . . . 48 7 Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . .-65°C to +150°C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Ambient Temperature Range ISL6622IBZ, ISL6622IRZ . . . . . . . . . . . . . . . . . . . .-40°C to +85°C ISL6622CBZ, ISL6622CRZ . . . . . . . . . . . . . . . . . . . 0°C to +70°C Maximum Operating Junction Temperature. . . . . . . . . . . . . +125°C Supply Voltage VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8V to 13.2V UVCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.75V to 13.2V CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 2. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 3. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. 4. Limits should be considered typical and are not production tested. Electrical Specifications Recommended Operating Conditions. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS - 8.2 - mA VCC SUPPLY CURRENT (Note 4) No Load Switching Supply Current IVCC ISL6622CBZ and ISL6622IBZ, fPWM = 300kHz, VVCC = 12V IVCC ISL6622CRZ and ISL6622IRZ, fPWM = 300kHz, VVCC = 12V IUVCC Standby Supply Current - 6.2 - mA - 2.0 - mA IVCC ISL6622CBZ and ISL6622IBZ, PWM Transition from 0V to 2.5V - 5.7 - mA IVCC ISL6622CRZ and ISL6622IRZ, PWM Transition from 0V to 2.5V - 5 - mA - 0.7 - mA VCC Rising Threshold 6.25 6.45 6.70 V VCC Falling Threshold IUVCC POWER-ON RESET 4.8 5.0 5.25 V LVCC Rising Threshold (Note 4) - 4.4 - V LVCC Falling Threshold (Note 4) - 3.4 - V - 500 - µA PWM INPUT (See “TIMING DIAGRAM” on page 6) Input Current (Note 4) IPWM VPWM = 5V VPWM = 0V - -430 - µA PWM Rising Threshold (Note 4) VCC = 12V - 3.4 - V PWM Falling Threshold (Note 4) VCC = 12V - 1.6 - V Three-State Lower Gate Falling Threshold (Note 4) VCC = 12V - 1.6 - V Three-State Lower Gate Rising Threshold (Note 4) VCC = 12V - 1.1 - V Three-State Upper Gate Rising Threshold (Note 4) VCC = 12V - 3.2 - V 4 FN6470.2 October 30, 2008 ISL6622 Electrical Specifications Recommended Operating Conditions. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested (Continued) PARAMETER SYMBOL MIN TYP MAX UNITS VCC = 12V - 2.8 - V tRU VVCC = 12V, 3nF Load, 10% to 90% - 26 - ns LGATE Rise Time (Note 4) tRL VVCC = 12V, 3nF Load, 10% to 90% - 18 - ns UGATE Fall Time (Note 4) tFU VVCC = 12V, 3nF Load, 90% to 10% - 18 - ns tFL Three-State Upper Gate Falling Threshold (Note 4) UGATE Rise Time (Note 4) LGATE Fall Time (Note 4) TEST CONDITIONS VVCC = 12V, 3nF Load, 90% to 10% - 12 - ns UGATE Turn-On Propagation Delay (Note 4) tPDHU VVCC = 12V, 3nF Load, Adaptive - 20 - ns LGATE Turn-On Propagation Delay (Note 4) tPDHL VVCC = 12V, 3nF Load, Adaptive - 10 - ns UGATE Turn-Off Propagation Delay (Note 4) tPDLU VVCC = 12V, 3nF Load - 10 - ns LGATE Turn-Off Propagation Delay (Note 4) tPDLL VVCC = 12V, 3nF Load - 10 - ns - 60 - ns 230 330 450 ns - 1.25 - A - 2.0 - Ω - A Diode Braking Holdoff Time (Note 4) tUG_OFF_DB VVCC = 12V Minimum LGATE ON-Time At Diode Emulation tLG_ON_DM VVCC = 12V Upper Drive Source Current IU_SOURCE VVCC = 12V, 3nF Load Upper Drive Source Impedance RU_SOURCE 20mA Source Current OUTPUT (Note 4) Upper Drive Sink Current IU_SINK VVCC = 12V, 3nF Load - 2 20mA Sink Current - 1.35 - Ω VVCC = 12V, 3nF Load - 2 - A - 1.35 - Ω Upper Drive Sink Impedance RU_SINK Lower Drive Source Current IL_SOURCE Lower Drive Source Impedance RL_SOURCE 20mA Source Current Lower Drive Sink Current IL_SINK VVCC = 12V, 3nF Load - 3 - A Lower Drive Sink Impedance RL_SINK 20mA Sink Current - 0.90 - Ω Functional Pin Description PACKAGE PIN # SOIC DFN PIN SYMBOL 1 1 UGATE Upper gate drive output. Connect to gate of high-side power N-Channel MOSFET. 2 2 BOOT Floating bootstrap supply pin for the upper gate drive. Connect the bootstrap capacitor between this pin and the PHASE pin. The bootstrap capacitor provides the charge to turn on the upper MOSFET. See “Internal Bootstrap Device” on page 8 for guidance in choosing the capacitor value. - 3 GD_SEL 3 4 PWM The PWM signal is the control input for the driver. The PWM signal can enter three distinct states during operation, see the three-state PWM Input section on page 6 for further details. Connect this pin to the PWM output of the controller. 4 5 GND Bias and reference ground. All signals are referenced to this node. It is also the power ground return of the driver. 5 6 LGATE 6 7 LVCC This pin provides power for the LGATE drive. Place a high quality low ESR ceramic capacitor from this pin to GND. - 8 UVCC This pin provides power to the upper gate drive. Its operating range is +5V to 12V. Place a high quality low ESR ceramic capacitor from this pin to GND. 7 9 VCC Connect this pin to 12V bias supply. This pin supplies power to the upper gate in the SOIC and to the LDO for the lower gate drive. Place a high quality low ESR ceramic capacitor from this pin to GND. 8 10 PHASE Connect this pin to the SOURCE of the upper MOSFET and the DRAIN of the lower MOSFET. This pin provides a return path for the upper gate drive. - 11 PAD FUNCTION This pin sets the LG drive voltage in PSI mode. Lower gate drive output. Connect to gate of the low-side power N-Channel MOSFET. Connect this pad to the power ground plane (GND) via thermally enhanced connection. 5 FN6470.2 October 30, 2008 ISL6622 1.5V<PWM<3.2V 1.0V<PWM<2.6V PWM tPDLU tPDHU tPDTS tUG_OFF_DB tPDTS UGATE tFU tRU LGATE tRL tFL tTSSHD tPDLL tPDHL FIGURE 1. TIMING DIAGRAM Description Operation and Adaptive Shoot-through Protection Designed for high speed switching, the ISL6622 MOSFET driver controls both high-side and low-side N-Channel FETs from one externally provided PWM signal. A rising transition on PWM initiates the turn-off of the lower MOSFET (see Figure 1). After a short propagation delay [tPDLL], the lower gate begins to fall. Typical fall time [tFL] is provided in the “Electrical Specifications” on page 4. Following a 25ns blanking period, adaptive shoot-through circuitry monitors the LGATE voltage and turns on the upper gate following a short delay time [tPDHU] after the LGATE voltage drops below ~1.75V. The upper gate drive then begins to rise [tRU] and the upper MOSFET turns on. A falling transition on PWM indicates the turn-off of the upper MOSFET and the turn-on of the lower MOSFET. A short propagation delay [tPDLU] is encountered before the upper gate begins to fall [tFU]. The adaptive shoot-through circuitry monitors the UGATE-PHASE voltage and turns on the lower MOSFET a short delay time [tPDHL] after the upper MOSFET’s PHASE voltage drops below +0.8V or 40ns after the upper MOSFET’s gate voltage [UGATE-PHASE] drops below ~1.75V. The lower gate then rises [tRL], turning on the lower MOSFET. These methods prevent both the lower and upper MOSFETs from conducting simultaneously (shoot-through), while adapting the dead time to the gate charge characteristics of the MOSFETs being used. This driver is optimized for voltage regulators with large step down ratio. The lower MOSFET is usually sized larger compared to the upper MOSFET because the lower MOSFET conducts for a longer time during a switching period. The lower gate driver is therefore sized much larger to meet this application requirement. The 0.8Ω ON-resistance and 3A sink current capability enable the lower gate driver to absorb the current injected into the lower gate through the drain-to-gate capacitor of the lower MOSFET and help prevent 6 shoot-through caused by the self turn-on of the lower MOSFET due to high dV/dt of the switching node. Advanced PWM Protocol (Patent Pending) The advanced PWM protocol of ISL6622 is specifically designed to work with Intersil VR11.1 controllers. When ISL6622 detects a PSI protocol sent by an Intersil VR11.1 controller, it turns on diode emulation and GVOT (described in next sections) operation; otherwise, it remains in normal CCM PWM mode. Another unique feature of ISL6622 and other Intersil drivers is the addition of a three-state shutdown window to the PWM input. If the PWM signal enters and remains within the shutdown window for a set holdoff time, the driver outputs are disabled and both MOSFET gates are pulled and held low. The shutdown state is removed when the PWM signal moves outside the shutdown window. Otherwise, the PWM rising and falling thresholds outlined in the “Electrical Specifications” on page 4 determine when the lower and upper gates are enabled. This feature helps prevent a negative transient on the output voltage when the output is shut down, eliminating the Schottky diode that is used in some systems for protecting the load from reversed output voltage events. Note that the LGATE will not turn off until the diode emulation minimum ON-time of 350ns is expired for a PWM low to tri-level (2.5V) transition. Diode Emulation Diode emulation allows for higher converter efficiency under light-load situations. With diode emulation active, the ISL6622 detects the zero current crossing of the output inductor and turns off LGATE. This prevents the low side MOSFET from sinking current and ensures that discontinuous conduction mode (DCM) is achieved. The LGATE has a minimum ON-time of 350ns in DCM mode. FN6470.2 October 30, 2008 ISL6622 The ISL6622 provides the user flexibility in choosing the gate drive voltage for efficiency optimization. During light load operation, the switching losses dominate system performance. Dropping down to a lower drive voltage with GVOT during light load operation can reduce the switching losses and maximize system efficiency. Figure 2 shows that the gate drive voltage optimization is accomplished via an internal low drop out regulator (LDO) that regulates the lower gate drive voltage. LVCC is driven to a lower voltage depending on the state of the internal PSI signal and the GD_SEL pin impedance. The input and output of this internal regulator is the VCC and LVCC pins, respectively. Both VCC and LVCC should be decoupled with a high quality low ESR ceramic capacitor. ISL6622 INTERNAL CIRCUIT EXTERNAL CIRCUIT SET BY PSI AND GD_SEL VCC VIN > GVOT LDO 1µF + - + - RCC Figure 3 illustrates the internal LDO’s variation with the average load current plotted over a range of temperatures spanning from -40°C to +120°C. Should finer tweaking of this LVCC voltage be necessary, a resistor (RCC) can be used to shunt the LDO, as shown in Figure 2. The resistor delivers part of the LGATE drive current, leaving less current going through the internal LDO, elevating the LDO’s output voltage. Further reduction in RCC’s value can raise the LVCC voltage further, as desired. Figure 4 also details the typical LDO performance when the pass element is fully enhanced, as it is the case when the driver operates in CCM. 12.0 VCC = 12V +40°C 11.8 11.6 LVCC VOLTAGE (V) Gate Voltage Optimization Technology (GVOT) 11.4 11.2 11.0 LVCC 10.8 LGATE DRIVER 1µF 10.6 0 20 40 60 80 100 AVERAGE LOAD CURRENT (mA) RCC = OPTION FOR HIGHER LVCC THAN PRE-SET BY GD_SEL FIGURE 3. TYPICAL LVCC VARIATION WITH LOAD (CCM) FIGURE 2. GATE VOLTAGE OPTIMIZATION (GVOT) DETAIL 9.0 8.5 +40°C +120°C -40°C 8.0 LVCC VOLTAGE (V) In the 8 Ld SOIC package, the ISL6622 drives the upper and lower gates close to VCC during normal PWM mode, while the lower gate drops down to a fixed 5.75V during PSI mode. The 10 Ld DFN part offers more flexibility: the upper gate can be driven from 5V to 12V via the UVCC pin, while the lower gate has a resistor-selectable drive voltage of 5.75V, 6.75V, and 7.75V during PSI mode. This provides the flexibility necessary to optimize applications involving trade-offs between gate charge and conduction losses. Table 1 shows the LDO output (LVCC) level set by the PWM input and GD_SEL pin impedance. GD_SEL TIED TO GND 7.5 +40°C +120°C -40°C 7.0 GD_SEL 4.5kΩ TO GND 6.5 +40°C +120°C -40°C 6.0 GD_SEL FLOATING 5.5 TABLE 1. LDO OPERATION AND OPTIONS 5.0 PWM INPUT GD_SEL PIN 0V 5V 0 20 40 60 80 AVERAGE LOAD CURRENT (mA) 100 Floating 5.75V (Typical; Fixed in SOIC Package) 4.5kΩ to GND 6.75V (Typical) Power-On Reset (POR) Function GND 7.75V (Typical) DON’T CARE 11.20V (Typical) During initial start-up, the VCC voltage rise is monitored. Once the rising VCC voltage exceeds rising POR threshold, operation of the driver is enabled and the PWM input signal takes control of the gate drives. If VCC drops below the POR falling threshold, operation of the driver is disabled. 5V 2.5V LVCC @ 50mA DC LOAD FIGURE 4. TYPICAL LVCC VARIATION WITH LOAD (DEM) 0V 7 FN6470.2 October 30, 2008 ISL6622 Pre-POR Overvoltage Protection . 1.6 1.2 1.0 0.8 0.6 QUGATE = 100nC 0.4 50nC 0.2 20nC 0.0 0.0 Internal Bootstrap Device The ISL6622 features an internal bootstrap Schottky diode. Simply adding an external capacitor across the BOOT and PHASE pins completes the bootstrap circuit. The bootstrap function is also designed to prevent the bootstrap capacitor from overcharging due to the large negative swing at the trailing-edge of the PHASE node. This reduces the voltage stress on the BOOT to PHASE pins. The bootstrap capacitor must have a maximum voltage rating well above the maximum voltage intended for UVCC. Its minimum capacitance value can be estimated from Equation 1: Q UGATE C BOOT_CAP ≥ -------------------------------------ΔV BOOT_CAP 1.4 CBOOT_CAP (µF) While VCC is below its POR level, the upper gate is held low and LGATE is connected to the PHASE pin via an internal 10kΩ (typically) resistor. By connecting the PHASE node to the gate of the low side MOSFET, the driver offers some passive protection to the load if the upper MOSFET(s) is or becomes shorted. If the PHASE node goes higher than the gate threshold of the lower MOSFET, it results in the progressive turn-on of the device and the effective clamping of the PHASE node’s rise. The actual PHASE node clamping level depends on the lower MOSFET’s electrical characteristics, as well as the characteristics of the input supply and the path connecting it to the respective PHASE node. (EQ. 1) Q G1 • UVCC Q UGATE = ------------------------------------ • N Q1 V GS1 where QG1 is the amount of gate charge per upper MOSFET at VGS1 gate-source voltage and NQ1 is the number of control MOSFETs. The ΔVBOOT_CAP term is defined as the allowable droop in the rail of the upper gate drive. Select results are exemplified in Figure 5. 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 ΔVBOOT_CAP (V) FIGURE 5. BOOTSTRAP CAPACITANCE vs BOOT RIPPLE VOLTAGE Power Dissipation Package power dissipation is mainly a function of the switching frequency (FSW), the output drive impedance, the layout resistance, and the selected MOSFET’s internal gate resistance and total gate charge (QG). Calculating the power dissipation in the driver for a desired application is critical to ensure safe operation. Exceeding the maximum allowable power dissipation level may push the IC beyond the maximum recommended operating junction temperature. The DFN package is more suitable for high frequency applications. See “Layout Considerations” on page 9 for thermal impedance improvement suggestions. The total gate drive power losses due to the gate charge of MOSFETs and the driver’s internal circuitry and their corresponding average driver current can be estimated using Equations 2 and 3, respectively: P Qg_TOT = P Qg_Q1 + P Qg_Q2 + I Q • VCC (EQ. 2) Q G1 • UVCC 2 P Qg_Q1 = --------------------------------------- • F SW • N Q1 V GS1 Q G2 • LVCC 2 P Qg_Q2 = -------------------------------------- • F SW • N Q2 V GS2 ⎛ Q G1 • UVCC • NQ1 Q G2 • LVCC • N Q2⎞ I DR = ⎜ ------------------------------------------------------ + -----------------------------------------------------⎟ • F SW + I Q V GS1 V GS2 ⎝ ⎠ (EQ. 3) where the gate charge (QG1 and QG2) is defined at a particular gate to source voltage (VGS1 and VGS2) in the corresponding MOSFET datasheet; IQ is the driver’s total quiescent current with no load at both drive outputs; NQ1 and NQ2 are number of upper and lower MOSFETs, respectively; UVCC and LVCC are the drive voltages for both upper and lower FETs, respectively. The IQ*VCC product is the quiescent power of the driver without a load. 8 FN6470.2 October 30, 2008 ISL6622 The total gate drive power losses are dissipated among the resistive components along the transition path, as outlined in Equation 4. The drive resistance dissipates a portion of the total gate drive power losses, the rest will be dissipated by the external gate resistors (RG1 and RG2) and the internal gate resistors (RGI1 and RGI2) of MOSFETs. Figures 6 and 7 show the typical upper and lower gate drives turn-on current paths. P DR = P DR_UP + P DR_LOW + I Q • VCC (EQ. 4) R LO1 R HI1 ⎛ ⎞ P Qg_Q1 P DR_UP = ⎜ -------------------------------------- + ----------------------------------------⎟ • --------------------2 ⎝ R HI1 + R EXT1 R LO1 + R EXT1⎠ R LO2 R HI2 ⎛ ⎞ P Qg_Q2 P DR_LOW = ⎜ -------------------------------------- + ----------------------------------------⎟ • --------------------R + R R + R 2 ⎝ HI2 EXT2 LO2 EXT2⎠ R GI1 R EXT1 = R G1 + ------------N Q1 R GI2 R EXT2 = R G2 + ------------N Q2 . BOOT UVCC D CGD RHI1 G RLO1 RL1 CDS RG1 CGS Q1 S PHASE FIGURE 6. TYPICAL UPPER-GATE DRIVE TURN-ON PATH LVCC D CGD RHI2 RLO2 G RL2 CDS RG2 CGS Q2 S FIGURE 7. TYPICAL LOWER-GATE DRIVE TURN-ON PATH Application Information help minimize such unwanted stress. The following advice is meant to lead to an optimized layout: • Keep decoupling loops (LVCC-GND and BOOT-PHASE) as short as possible. • Minimize trace inductance, especially low-impedance lines: all power traces (UGATE, PHASE, LGATE, GND, LVCC) should be short and wide, as much as possible. • Minimize the inductance of the PHASE node: ideally, the source of the upper and the drain of the lower MOSFET should be as close as thermally allowable. • Minimize the input current loop: connect the source of the lower MOSFET to ground as close to the transistor pin as feasible; input capacitors (especially ceramic decoupling) should be placed as close to the drain of upper and source of lower MOSFETs as possible. In addition, for improved heat dissipation, place copper underneath the IC whether it has an exposed pad or not. The copper area can be extended beyond the bottom area of the IC and/or connected to buried power ground plane(s) with thermal vias. This combination of vias for vertical heat escape, extended surface copper islands, and buried planes combine to allow the IC and the power switches to achieve their full thermal potential. Upper MOSFET Self Turn-On Effect at Start-up Should the driver have insufficient bias voltage applied, its outputs are floating. If the input bus is energized at a high dV/dt rate while the driver outputs are floating, due to self-coupling via the internal CGD of the MOSFET, the gate of the upper MOSFET could momentarily rise up to a level greater than the threshold voltage of the device, potentially turning on the upper switch. Therefore, if such a situation could conceivably be encountered, it is a common practice to place a resistor (RUGPH) across the gate and source of the upper MOSFET to suppress the Miller coupling effect. The value of the resistor depends mainly on the input voltage’s rate of rise, the CGD/CGS ratio, as well as the gatesource threshold of the upper MOSFET. A higher dV/dt, a lower CDS/CGS ratio, and a lower gate-source threshold upper FET will require a smaller resistor to diminish the effect of the internal capacitive coupling. For most applications, the integrated 20kΩ resistor is sufficient, not affecting normal performance and efficiency. –V Layout Considerations During switching of the devices, the parasitic inductances of the PCB and the power devices’ packaging (both upper and lower MOSFETs) leads to ringing, possibly in excess of the absolute maximum rating of the devices. Careful layout can DS ⎛ ----------------------------------⎞ dV ⎜ ------- ⋅ R ⋅ C ⎟ dV iss⎟ V GS_MILLER = ------- ⋅ R ⋅ C rss ⎜ 1 – e dt ⎜ ⎟ dt ⎜ ⎟ ⎝ ⎠ R = R UGPH + R GI C rss = C GD (EQ. 5) C iss = C GD + C GS The coupling effect can be roughly estimated with Equation 5, which assumes a fixed linear input ramp and neglects the clamping effect of the body diode of the upper drive and the bootstrap capacitor. Other parasitic 9 FN6470.2 October 30, 2008 ISL6622 Gate Drive Voltage Options components such as lead inductances and PCB capacitances are also not taken into account. Figure 8 provides a visual reference for this phenomenon and its potential solution. UVCC Intersil provides various gate drive voltage options in the ISL6622 product family, as shown in Table 2. The ISL6622 can drop the low-side MOSFET’s gate drive voltage when operating in DEM, while the high-side FET’s gate drive voltage of the DFN package can be connected to VCC or LVCC. VIN > BOOT CBOOT D CGD RUGPH ISL6622 UGATE 20kΩ G CDS RG CGS QUPPER S The ISL6622A allows the low-side MOSFET(s) to operate from an externally-provided rail as low as 5V, eliminating the LDO losses, while the high-side MOSFET’s gate drive voltage of the DFN package can be connected to VCC or LVCC. The ISL6622B sets the low-side MOSFET’s gate drive voltage at a fixed, programmable LDO level, while the high-side FETs’ gate drive voltage of the DFN package can be connected to VCC or LVCC. PHASE FIGURE 8. GATE TO SOURCE RESISTOR TO REDUCE UPPER MOSFET MILLER COUPLING TABLE 2. ISL6622 FAMILY BIAS OPTIONS LVCC POWER RAILS ISL6622 ISL6622A ISL6622B PSI = LOW PSI = HIGH UVCC SOIC 5.75V 11.2V VCC DFN Programmable 11.2V Own Rail SOIC Own Rail VCC DFN Own Rail Own Rail SOIC 5.75V VCC DFN Programmable Own Rail 10 VCC Operating Voltage Ranges from 6.8V to 13.2V FN6470.2 October 30, 2008 ISL6622 Dual Flat No-Lead Plastic Package (DFN) 2X 0.15 C A D A L10.3x3 10 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE MILLIMETERS 2X 0.15 C B SYMBOL MIN 6 INDEX AREA 0.80 0.90 1.00 - - - 0.05 - 0.28 5,8 2.05 7,8 1.65 7,8 0.20 REF 0.18 D 1.95 E 0.10 C 0.08 C SIDE VIEW C SEATING PLANE 1 e 1.60 - 0.50 BSC - k 0.25 - - L 0.30 0.35 0.40 N 10 Nd 5 3 3. Nd refers to the number of terminals on D. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. E2/2 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. NX L N-1 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. NX b 5 (Nd-1)Xe REF. 8 2 2. N is the number of terminals. E2 e - 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. NX k 8 1.55 NOTES: D2/2 2 N - Rev. 3 6/04 D2 (DATUM B) 2.00 8 7 6 INDEX AREA (DATUM A) A3 - 3.00 BSC E2 A 0.23 3.00 BSC D2 B NOTES A b TOP VIEW MAX A1 A3 E NOMINAL 0.10 M C A B 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. BOTTOM VIEW C L 0.415 NX (b) (A1) 0.200 5 L NX L e SECTION "C-C" NX b C C C TERMINAL TIP FOR ODD TERMINAL/SIDE 11 FN6470.2 October 30, 2008 ISL6622 Small Outline Plastic Packages (SOIC) M8.15 (JEDEC MS-012-AA ISSUE C) N 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA H 0.25(0.010) M B M INCHES E SYMBOL -B- 1 2 3 L SEATING PLANE -A- A D h x 45° -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 3 E 0.1497 0.1574 3.80 4.00 4 e α B S 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N α NOTES: MILLIMETERS 8 0° 8 8° 0° 7 8° 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 12 FN6470.2 October 30, 2008