2M x 8 - Bit Dynamic RAM 2k Refresh (Hyper Page Mode- EDO) HYB5117805BSJ -50/-60/-70 Advanced Information • 2 097 152 words by 8-bit organization • 0 to 70 °C operating temperature • Performance: -50 -60 -70 tRAC RAS access time 50 60 70 ns tCAC CAS access time 13 15 20 ns tAA Access time from address 25 30 35 ns tRC Read/Write cycle time 84 104 124 ns tHPC Hyper page mode (EDO) cycle time 20 25 30 ns • Single + 5 V (± 10 %) supply • Low power dissipation max. 660 mW active (-50 version) max. 605 mW active (-60 version) max. 550 mW active (-70 version) 11 mW standby (TTL) 5.5. mW standby (MOS) • Read, write, read-modify-write, CAS-before-RAS refresh, RAS-only refresh, hidden refresh, self refresh and test mode • Hyper page mode (EDO) capability • All inputs, outputs and clocks fully TTL-compatible • 2048 refresh cycles / 32 ms (2k-Refresh) • Plastic Package: Semiconductor Group P-SOJ-28-3 400 mil 1 1.96 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM The HYB 5117805BSJ is a 16 MBit dynamic RAM organized as 2 097 152 words by 8-bits. The HYB 5117805BSJ utilizes a submicron CMOS silicon gate process technology, as well as advanced circuit techniques to provide wide operating margins, both internally and for the system user. Multiplexed address inputs permit the HYB 5117805BSJ to be packaged in a standard SOJ 28 plastic package with 400 mil width. These packages provide high system bit densities and are compatible with commonly used automatic testing and insertion equipment. System-oriented features include single + 5 V (± 10 %) power supply, direct interfacing with high-performance logic device families such as Schottky TTL. Ordering Information Type Ordering Code Package Descriptions HYB 5117805BJ-50 Q67100-Q1104 P-SOJ-28-3 400 mil DRAM (access time 50 ns) HYB 5117805BJ-60 Q67100-Q1105 P-SOJ-28-3 400 mil DRAM (access time 60 ns) HYB 5117805BJ-70 Q67100-Q1106 P-SOJ-28-3 400 mil DRAM (access time 70 ns) Pin Names A0-A10 Row Address Inputs A0-A9 Column Address Inputs RAS Row Address Strobe OE Output Enable I/O1-I/O8 Data Input/Output CAS Column Address Strobe WE Read/Write Input VCC Power Supply (+ 5 V) VSS Ground (0 V) N.C. not connected Semiconductor Group 2 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM P-SOJ-28-3 VCC I/O1 I/O2 I/O3 I/O4 WE RAS N.C. A10 A0 A1 A2 A3 VCC 400 mil O 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 Pin Configuration Semiconductor Group 3 VSS I/O8 I/O7 I/O6 I/O5 CAS OE A9 A8 A7 A6 A5 A4 VSS HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM I/O1 I/O2 I/O8 WE CAS & . Data in Buffer 10 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 No. 2 Clock Generator 8 Column Address Buffer(10) 10 Data out Buffer OE 8 Column Decoder Refresh Controller Sense Amplifier I/O Gating Refresh Counter (11) 8 1024 x8 11 Row 11 RAS Address Buffers(11) 11 Row Decoder 2048 Memory Array 2048x1024x8 No. 1 Clock Generator Voltage Down Generator Block Diagram Semiconductor Group 4 VCC VCC (internal) HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM Absolute Maximum Ratings Operating temperature range ............................................................................................0 to 70 °C Storage temperature range.........................................................................................– 55 to 150 °C Input/output voltage ................................................................................-0.5 to min (Vcc+0.5,7.0) V Power supply voltage...................................................................................................-1.0V to 7.0 V Power dissipation..................................................................................................................... 1.0 W Data out current (short circuit) ................................................................................................ 50 mA Note: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage of the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC Characteristics TA = 0 to 70 °C, VSS = 0 V, VCC = 5 V ± 10 %; tT = 2 ns Parameter Symbol Limit Values min. max. Unit Test Condition Input high voltage VIH 2.4 Vcc+0.5 V 1) Input low voltage VIL – 0.5 0.8 V 1) Output high voltage (IOUT = – 5 mA) VOH 2.4 – V 1) Output low voltage (IOUT = 4.2 mA) VOL – 0.4 V 1) Input leakage current (0 V ≤ VIH ≤ Vcc + 0.3V, all other pins = 0 V) II(L) – 10 10 µA 1) Output leakage current (DO is disabled, 0 V ≤ VOUT ≤ Vcc + 0.3V) IO(L) – 10 10 µA 1) Average VCC supply current: ICC1 -50 ns version -60 ns version -70 ns version (RAS, CAS, address cycling: tRC = tRC min.) – – – 120 110 100 mA mA mA 2) 3) 4) Standby VCC supply current (RAS = CAS = VIH) ICC2 – 2 mA – Average VCC supply current, during RAS-only refresh cycles: -50 ns version -60 ns version -70 ns version (RAS cycling, CAS = VIH, tRC = tRC min.) ICC3 – – – 120 110 100 mA mA mA 2) 4) Semiconductor Group 5 2) 3) 4) 2) 3) 4) 2) 4) 2) 4) HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM DC Characteristics TA = 0 to 70 °C, VSS = 0 V, VCC = 5 V ± 10 %; tT = 2 ns Parameter Symbol Average VCC supply current, ICC4 during hyper page mode: -50 ns version -60 ns version -70 ns version (RAS = VIL, CAS, address cycling:tPC = tPC min.) Standby VCC supply current (RAS = CAS = VCC – 0.2 V) ICC5 Average VCC supply current, during CASbefore-RAS refresh mode: -50 ns version -60 ns version -70 ns version (RAS, CAS cycling: tRC = tRC min.) ICC6 Average Self Refresh Current ICC7 Limit Values min. max. Unit Test Condition – – – 70 55 45 mA mA mA – 1 mA – – – 120 110 100 mA mA mA _ 1 mA 2) 3) 4) 2) 3) 4) 2) 3) 4) 1) 2) 4) 2) 4) 2) 4) (CBR cycle with tRAS>TRASSmin., CAS held low, WE=Vcc-0.2V, Address and Din=Vcc - 0.2V or 0.2V) Capacitance TA = 0 to 70 °C,VCC = 5 V ± 10 %, f = 1 MHz Parameter Symbol Limit Values min. max. Unit Input capacitance (A0 to A10) CI1 – 5 pF Input capacitance (RAS, CAS, WE, OE) CI2 – 7 pF I/O capacitance (I/O1-I/O8) CIO – 7 pF Semiconductor Group 6 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM AC Characteristics 5)6) TA = 0 to 70 °C,VCC = 5 V ± 10 %, tT = 2 ns Parameter 16E Limit Values Symbol -50 Unit Note -60 -70 min. max. min. max. min. max. common parameters Random read or write cycle time tRC 84 – 104 – 124 – ns RAS precharge time tRP 30 – 40 – 50 – ns RAS pulse width tRAS 50 10k 60 10k 70 10k ns CAS pulse width tCAS 8 10k 10 10k 12 10k ns Row address setup time tASR 0 – 0 – 0 – ns Row address hold time tRAH 8 – 10 – 10 – ns Column address setup time tASC 0 – 0 – 0 – ns Column address hold time tCAH 8 – 10 – 12 – ns RAS to CAS delay time tRCD 12 37 14 45 14 53 ns RAS to column address delay tRAD 10 25 12 30 12 35 ns RAS hold time tRSH 13 15 – 17 – ns CAS hold time tCSH 40 50 – 60 – ns CAS to RAS precharge time tCRP 5 – 5 – 5 – ns Transition time (rise and fall) tT 1 50 1 50 1 50 ns Refresh period tREF – 32 – 32 – 32 ms Access time from RAS tRAC – 50 – 60 – 70 ns 8, 9 Access time from CAS tCAC – 13 – 15 – 17 ns 8, 9 Access time from column address tAA – 25 – 30 – 35 ns 8,10 OE access time – 13 – 15 – 17 ns Column address to RAS lead time tRAL 25 – 30 – 35 – ns Read command setup time tRCS 0 – 0 – 0 – ns Read command hold time tRCH 0 – 0 – 0 – ns 11 Read command hold time referenced to RAS tRRH 0 – 0 – 0 – ns 11 CAS to output in low-Z tCLZ 0 – 0 – 0 – ns 8 Output buffer turn-off delay tOFF 0 13 0 15 0 17 ns 12 Output turn-off delay from OE tOEZ 0 13 0 15 0 17 ns 12 7 Read Cycle Semiconductor Group tOEA 7 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM AC Characteristics (cont’d) 5)6) TA = 0 to 70 °C,VCC = 5 V ± 10 %, tT = 2 ns Parameter 16E Limit Values Symbol -50 Unit Note -60 -70 min. max. min. max. min. max. Data to CAS low delay tDZC 0 – 0 – 0 – ns 13 Data to OE low delay tDZO 0 – 0 – 0 – ns 13 CAS high to data delay tCDD 10 – 13 – 15 – ns 14 OE high to data delay tODD 10 – 13 – 15 – ns 14 Write command hold time tWCH 8 – 10 – 10 – ns Write command pulse width tWP 8 – 10 – 10 – ns Write command setup time tWCS 0 – 0 – 0 – ns Write command to RAS lead time tRWL 13 – 15 – 17 – ns Write command to CAS lead time tCWL 13 – 15 – 17 – ns Data setup time tDS 0 – 0 – 0 – ns 16 Data hold time tDH 8 – 10 – 12 – ns 16 Read-write cycle time tRWC 113 – 138 – 162 – ns RAS to WE delay time tRWD 64 – 77 – 89 – ns 15 CAS to WE delay time tCWD 27 – 32 – 36 – ns 15 Column address to WE delay time tAWD 39 – 47 – 54 – ns 15 OE command hold time tOEH 10 – 13 – 15 – ns Hyper page mode (EDO) cycle time tHPC 20 – 25 – 30 – ns CAS precharge time tCP 8 – 10 – 10 – ns Access time from CAS precharge tCPA – 27 – 32 – 37 ns Output data hold time tCOH 5 – 5 – 5 – ns RAS pulse width in EDO mode tRAS 50 200k 60 200k 70 200k ns CAS precharge to RAS Delay tRHPC 27 – – – Write Cycle 15 Read-modify-Write Cycle Hyper Page Mode (EDO) Cycle Semiconductor Group 8 32 37 ns 7 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM AC Characteristics (cont’d) 5)6) TA = 0 to 70 °C,VCC = 5 V ± 10 %, tT = 2 ns Parameter 16E Limit Values Symbol -50 min. Unit Note -60 max. min. -70 max. min. max. Hyper Page Mode (EDO) Read-modify-Write Cycle Hyper page mode (EDO) readwrite cycle time tPRWC 58 – 68 – 77 – ns CAS precharge to WE tCPWD 41 – 49 – 56 – ns CAS setup time tCSR 10 – 10 – 10 – ns CAS hold time tCHR 10 – 10 – 10 – ns RAS to CAS precharge time tRPC 5 – 5 – 5 – ns Write to RAS precharge time tWRP 10 – 10 – 10 – ns Write hold time referenced to RAS tWRH 10 – 10 – 10 – ns tCPT 35 – 40 – 40 – ns RAS pulse width tRASS 100k – 100k – 100k – ns 17 RAS precharge time tRPS 95 – 110 – 130 – ns 17 CAS hold time tCHS -50 – -50 – -50 – ns 17 Write command setup time tWTS 10 – 10 – 10 – ns Write command hold time tWTH 10 – 10 – 10 – ns CAS hold time tCHRT 30 – 30 – 30 – ns CAS-before-RAS Refresh Cycle CAS-before-RAS Counter Test Cycle CAS precharge time (CASbefore-RAS counter test cycle) Self Refresh Cycle Test Mode Semiconductor Group 9 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM Notes: 1) All voltages are referenced to VSS. 2) ICC1, ICC3, ICC4 and ICC6 depend on cycle rate. 3) ICC1 and ICC4 depend on output loading. Specified values are obtained with the output open. 4) Address can be changed once or less while RAS = Vil. In case of ICC4 it can be changed once or less during a hyper page mode (EDO) cycle 5) An initial pause of 200 µs is required after power-up followed by 8 RAS cycles of which at least one cycle has to be a refresh cycle, before proper device operation is achieved. In case of using the internal refresh counter, a minimum of 8 CAS-before-RAS initialization cycles instead of 8 RAS cycles are required. 6) AC measurements assume tT = 2 ns. 7) VIH (min.) and VIL (max.) are reference levels for measuring timing of input signals. Transition times are also measured between VIH and VIL. 8) Measured with the specified current load and 100 pF at Vol = 0.8 V and Voh = 2.0 V. Access time is determined by the latter of tRAC, tCAC, tAA,tCPA, tOEA . tCAC is measured from tristate. 9) Operation within the tRCD (max.) limit ensures that tRAC (max.) can be met. tRCD (max.) is specified as a reference point only. If tRCD is greater than the specified tRCD (max.) limit, then access time is controlled by tCAC. 10) Operation within the tRAD (max.) limit ensures that tRAC (max.) can be met. tRAD (max.) is specified as a reference point only. If tRAD is greater than the specified tRAD (max.) limit, then access time is controlled by tAA. 11) Either tRCH or tRRH must be satisfied for a read cycle. 12) tOFF (max.), tOEZ (max.) define the time at which the output achieves the open-circuit conditions and are not referenced to output voltage levels. tOFF is referenced from the rising edge of RAS or CAS, whichever occurs last. 13) Either tDZC or tDZO must be satisfied. 14) Either tCDD or tODD must be satisfied. 15) tWCS, tRWD, tCWD and tAWD are not restrictive operating parameters. They are included in the data sheet as electrical characteristics only. If tWCS > tWCS (min.), the cycle is an early write cycle and data out pin will remain open-circuit (high impedance) through the entire cycle; if tRWD > tRWD (min.), tCWD > tCWD (min.) and tAWD > tAWD (min.), the cycle is a read-write cycle and I/O will contain data read from the selected cells. If neither of the above sets of conditions is satisfied, the condition of I/O (at access time) is indeterminate. 16) These parameters are referenced to the CAS leading edge in early write cycles and to the WE leading edge in read-write cycles. 17)When using Self Refresh mode, the following refresh operations must be performed to ensure proper DRAM operation: If row addresses are being refreshed on an evenly distributed manner over the refresh interval using CBR refresh cycles, then only one CBR cycle must be performed immediately after exit from Self Refresh. If row addresses are being refreshed in any other manner (ROR - Distributed/Burst; or CBR-Burst) over the refresh interval, then a full set of row refreshes must be performed immediately before entry to and immediately after exit from Self Refresh Semiconductor Group 10 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRC tRAS RAS V IH VIL tCSH V IH VIL tRAD tASR Address V IH VIL tCRP tRSH tCAS tRCD CAS tRP tRAL tCAH tASC tASR Column Row Row tRCH tRAH tRCS tRRH V WE OE I/O (Inputs) IH VIL tAA tOEA V IH VIL tCDD tDZC tODD tDZO V IH tCAC VIL tCLZ V OH I/O (Outputs) V Hi Z tOFF tOEZ Valid Data Out Hi Z OL tRAC WL1 “H” or “L” Read Cycle Semiconductor Group 11 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRC tRAS tRP V IH RAS VIL tCSH tRCD tRSH tCAS V IH CAS VIL tRAD tASR Address V IH tRAL Row OE . Row tCWL tWCS t WP IH VIL tWCH tRWL V IH VIL tDS I/O (Inputs) tASR Column VIL V WE tCAH tASC tRAH tCRP tDH V IH Valid Data In VIL V OH I/O (Outputs) V Hi Z OL WL2 “H” or “L” Write Cycle (Early Write) Semiconductor Group 12 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRC tRAS tRP V IH RAS VIL tCSH tRCD V IH CAS VIL tRAD tASR tCRP tRSH tCAS tCAH tASC tRAL tASR . V IH Address V IL Row tCWL tRWL tWP tRAH V WE Row Column IH VIL tOEH V OE IH tODD tDS tOEZ VIL tDZO tDZC I/O (Inputs) tDH V IH Valid Data VIL tCLZ tOEA V OH I/O (Outputs) V Hi-Z Hi-Z OL “H” or “L” WL3 Write Cycle (OE Controlled Write) Semiconductor Group 13 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRWC tRAS RAS V IH tRP tCSH VIL tRSH tCAS tRCD V tCRP IH CAS VIL tRAH tCAH tASR tASC tASR V IH Address VIL Row Column Row tCWL tRWL tAWD tRAD tCWD tRWD tWP V IH WE VIL tAA tRCS tOEH tOEA V IH OE VIL tDS tDZO tDZC I/O (Inputs) tDH V IH Valid Data in VIL tCLZ tODD tCAC tOEZ V OH I/O (Outputs) VOL Data Out tRAC “H” or “L” WL4 Read-Write (Read-Modify-Write) Cycle Semiconductor Group 14 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRP tRAS V tRCD IH RAS tRHCP VIL tRSH tHPC tCRP tCAS tCP tCAS tCRP tCAS V IH CAS VIL tCSH tASR Address tRAH tASC tRAL tCAH V IH VIL Row Column 1 tASC tCAH tASC tCAH Column 2 Column N tRAD tRRH tRCH tRCS WE VIH VIL tOES OH V tCPA tCPA tOFF tOEA V OE tCAC tAA tCAC tAA OL tRAC tAA tCAC tOEZ tCOH tCLZ V I/O IH (Output) V IL Data Out 1 Data Out 2 Data Out N WL5 “H” or “L” Hyper Page Mode (EDO) Read Cycle Semiconductor Group tCOH 15 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRP tRAS V tRHCP tRCD IH RAS VIL tRSH tHPC tCRP tCAS tCAS tCP tCRP tCAS V IH CAS VIL tCSH tASR tRAH tASC tRAL tCAH tASC tCAH tASC tCAH Column 2 Column N V IH Address VIL Row Addr Column 1 tRAD tWCS tCWL tCWL tWCH tWCS tWCH tWP tWP WE VIH tRWL tCWL tWCS tWCH tWP VIL V OE OH V OL tDS tDH tDS tDH tDS tDH V IH I/O (Input) V IL Data In 1 Data In 2 “H” or “L” WL8 Hyper Page Mode (EDO) Early Write Cycle Semiconductor Group Data In N 16 Semiconductor Group 17 IH IH IH IH V IH V IL V V IL V V IL V V IL V V IL IH Hyper Page Mode (EDO) Late Write and Read-Modify Write Cycle OL OH I/O (Outputs) V V I/O (Inputs) V IL OE WE Address CAS RAS V tASR Row tRAH tRAD tRAC tCAS tAA tOEA tCAC Data In tDS tOEH tCLZ tOEZ tWP tDS tDH Data In tODD Data Out tOEA tAWD tCPA tAA tDZC tCAS tPRWC tCPWD tCWD tCAH Column tASC tCP tCWL tWP tOEZ tDH tODD Data Out tAWD tRWD tCWD Column tASC tCAH tDZC tCLZ tDZO tRCS tRCD tCSH tRASP tOEH tDZC tCWL tAWD tCAC tAA tCLZ tCPA tRAL Data Out tDS tDH tOEH tRWL tCWL tWP Data In tODD tCPWD tCWD tOEA Column tASC tCAH tCAS tRSH tCRP Row tASR tRP HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM WL17 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRC tRAS RAS tRP V IH VIL tCRP tRPC CAS V IH VIL tRAH tASR tASR V Address IH Row VIL Row V OH I/O (Outputs) V HI-Z OL “H” or “L” WL9 RAS-Only Refresh Cycle Semiconductor Group 18 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRC tRP tRAS tRP V RAS IH VIL tRPC tCSR tCRP tCP CAS tRPC tCHR V IH VIL tWRP tWRH V WE IH VIL tOEZ V IH OE VIL tCDD I/O (Inputs) V IH VIL tODD V OH I/O (Outputs)VOL HI-Z tOFF “H” or “L” WL10 CAS-Before-RAS Refresh Cycle Semiconductor Group 19 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRC tRC RAS tRP tRAS V tRP tRAS IH VIL tRSH tRCD tCRP tCHR V CAS IH tRAD VIL tWRP tASC tASR tRAH tASR tWRH tCAH V Address IH VIL Column Row Row tRRH tRCS V WE IH VIL tAA tOEA V OE IH VIL tDZC tCDD tDZO tODD V I/O (Inputs) IH VIL tCAC tOFF tCLZ tOEZ tRAC V OH I/O (Outputs) V Valid Data Out HI-Z OL “H” or “L” WL11 Hidden Refresh Cycle (Read) Cycle Semiconductor Group 20 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRC tRC tRP RAS tRAS V IH WE VIL tCHR tCRP tRAD tRAH tASC tCAH V IH VIL Row tASR Row Column tWCS tWRP tWCH tWRH tWP V IH VIL tDS I/O (Input) tRSH V IH tASR Address tRP VIL tRCD CAS tRAS V IH tDH Valid Data V IL V OH I/O (Output) V OL HI-Z “H” or “L” WL12 Hidden Refresh Early Write Cycle Semiconductor Group 21 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRASS tRP RAS tRPS V IH VIL tRPC tCP V CAS tCRP tCHS tCSR IH VIL tWRP tWRH V WE OE IH VIL V IH VIL tCDD I/O (Inputs) V IH VIL tODD tOEZ V OH I/O (Outputs) V OL HI-Z tOFF “H” or “L” WL13 Self Refresh Semiconductor Group 22 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRP tRAS Read Cycle: RAS V IH V IL tRSH tCAS tCP tCHR tCSR CAS V IH V IL tRAL tASC Address V IH Column V IL tWRP WE OE I/O (Inputs) I/O (Outputs) V IL Row tWRH tOEA tRCS V IH V IL tDZC V IH V IL tODD tDZO VOH VOL V IH V IL OE V IH V IL I/O (Inputs) V IH tOEZ Data Out tWCS tRWL tCWL tWCH tWRH tDS V IH V IL HI-Z CAS-Before-RAS Refresh Counter Test Cycle Semiconductor Group tDH Data In V IL 23 tCDD tOFF tCLZ Write Cycle: I/O (Outputs) tRRH tAA tCAC V IH tWRP WE tASR tCAH tRCH HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM tRC tRP tRAS V RAS tRP IH VIL tRPC tCP tCSR tCHR tRPC tCRP V CAS IH VIL tASR tRAH V Address IH Row VIL tWTS tWTH V WE IH VIL V OE IH VIL V I/O IH (Inputs) V IL tODD HI-Z tCDD tOEZ V OH I/O (Outputs) V HI-Z OL tOFF “H” or “L” WL15 Test Mode Entry Semiconductor Group 24 HYB5117805BSJ-50/-60/-70 2M x 8-EDO DRAM Plastic Package P-SOJ-28-3 (400mil) (Small Outline J-lead, SMD) 10.16 30 0.51 -0.13 - O 0.81max 1.27 1) +0.13 0.18 M 9.4 + 0.25 - 0.1 28x 11.18 0.18 +0.13 - GPJ05699 28 15 1 14 18.54 1) -0.25 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side Package Outline Semiconductor Group 25 M