AH1884 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Description Pin Assignments AH1884 is with two Hall effect plates and dual CMOS output driver, mainly designed for battery–operation, hand-held equipment (such as Cellular and Cordless Phone, PDA). The total operation power is down to 15uW in the 1.8V supply. ( Top View ) Out 2 1 GND 2 NC 3 Either north or south pole of sufficient strength will turn the output on. The output will be turned off under no magnetic field. While the magnetic flux density (B) is larger than operate point (Bop), the output will be turned on (low), the output is held until B is lower than release point (Brp), then turned off. Applications • • • • • • • • • • • • Package: SOT553 “Green” Molding Compound 4 Vdd SOT553 Features Micropower operation Operation with North or South Pole 1.65V to 3.3V battery operation Chopper stabilized • Superior temperature stability • Extremely Low Switch-Point Drift • Insensitive to Physical Stress Good RF noise immunity -40°C to 85°C operating temperature ESD ＞ 4KV in human body mode 5 Out 1 Cellular phone PDA Cordless phone Typical Application Circuit Vdd Output 1 AH1884 Output 2 GND AH1884 Document number: DS31171 Rev. 6 - 2 1 of 7 www.diodes.com September 2010 © Diodes Incorporated AH1884 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Pin Descriptions Pin Name P/I/O Pin # Out 2 GND NC Vdd Out 1 O P/I 1 2 3 4 5 P/I O Description Output Pin ( active High ) Ground No Connection Power Supply Voltage Output Pin ( active Low ) Functional Block Diagram Vdd Power switch Offset Cancelling Hall Plate Latch Amp Out1 GND Vdd Logical Offset Cancelling Hall Plate Amp Latch Out2 GND Absolute Maximum Ratings (TA = 25°C) Symbol Vdd B TS PD TJ Characteristics Supply voltage Magnetic flux density Storage Temperature Range Package Power Dissipation Maximum Junction Temperature Values Unit 5 V Unlimited -65 to +150 230 150 °C mW °C Recommended Operating Conditions (TA = 25°C) Symbol Vdd TA Parameter Conditions Rating Unit Supply Voltage Operating 1.65 to 3.3 V Operating Temperature Range Operating -40 to +85 °C AH1884 Document number: DS31171 Rev. 6 - 2 2 of 7 www.diodes.com September 2010 © Diodes Incorporated AH1884 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Electrical Characteristics (TA = 25°C, Vdd = 1.8V, unless otherwise specified) Symbol Characteristic Conditions Min Typ. Max Unit VOH Output On Voltage (High side) IO= -0.5mA Vdd-0.2 - - V VOL Output On Voltage (Low side) IO= 0.5mA - - 0.2 V Chip enable - 2 4 mA Supply Current Chip disable - 5 8 uA average supply current - 7 12 uA Idd(en) Idd(dis) Idd(avg) Tawake Awake Time - 50 100 µs Tperiod Period - 50 100 ms Duty Cycle - 0.1 - % D.C. Magnetic Characteristics (TA = 25°C, Vdd = 1.8V~3.0V, Note 1 & 2) (1mT=10 Gauss) Symbol Characteristic Bops(south pole to brand side) Operate Point Bopn(north pole to brand side) Brps(south pole to brand side) Release Point Brpn(north pole to brand side) Bhy(|Bopx|-|Brpx|) Notes: Hysteresis Min Typ. Max - 37 55 -55 -37 - 15 29 - - -29 -15 3 8 - Unit Gauss 1. Typical data is at Ta = 25°C, Vdd = 3V, and for design information only. 2. The magnetic characteristics may vary with supply voltage, operating temperature and after soldering. Output1 V dd ( off-state ) Turn off Turn on ( on-state ) B hy ( Output Voltage ) ( Output Voltage ) Output1 Document number: DS31171 Rev. 6 - 2 Turn off V dd B hy Turn on Vsat Vsat Bopn B rpn 0 ( Magnetic flux density B ) AH1884 ( off-state ) ( on-state ) 0 B rps Bops ( Magnetic flux density B ) 3 of 7 www.diodes.com September 2010 © Diodes Incorporated AH1884 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Typical Operating Characteristics Switching Point AH1884 Hysteresis vs Temp. (Vdd = 1.8V) AH1884 Hysteresis vs Vdd (Ta =25 Degree C) Gauss (G) 60 50 40 30 40 Brpn 20 10 Brpn 20 Bopn Bopn Brps Gauss(G) 0 -10 -20 Bhys_n Bhys_s -30 -40 Brps 0 Bops 1.8 2.3 2.8 Bhys_s -40 -50 -50 -25 0 25 50 75 100 -60 Temp. ℃ Vdd(V) Supply Current AH1884 Idd(avg.) vs Temp. AH1884 Idd(avg.) vs Vdd 10 (Ta=25 Degree C) 12 9 10 8 Idd(avg.) unit : uA Idd(avg.) 8 unit: uA 7 6 Icc (avg) uA 6 5 Vdd = 1.8V 4 4 Vdd = 2.5V 2 3 2 0 -50 -25 0 25 50 75 100 1.8 Temp. ℃ AH1884 Document number: DS31171 Rev. 6 - 2 Bops Bhys_n -20 2.3 2.8 Vdd(V) 4 of 7 www.diodes.com September 2010 © Diodes Incorporated AH1884 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Performance Characteristics TA (°C) 25 50 60 70 80 85 90 100 110 120 130 140 150 PD (mW) 230 184 166 147 129 120 110 92 74 55 37 18 0 P D (m W ) P o w e r D is s i p a tio n C u rv e 300 200 100 0 -40 0 25 50 75 85 100 12 5 150 o TA ( C) Ordering Information AH 1884 - Z G - 7 Device AH1884-ZG-7 Notes: Package Green Packing Z : SOT553 G : Green 7 : Tape & Reel Package Code Z Packaging (Note 3 & 4) SOT553 7” Tape and Reel Quantity Part Number Suffix 3000/Tape & Reel -7 3. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. 4. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf. AH1884 Document number: DS31171 Rev. 6 - 2 5 of 7 www.diodes.com September 2010 © Diodes Incorporated AH1884 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH Marking Information (1) SOT553 ( Top View ) XX Y W X Part Number AH1884 XX : Identification Code Y : Year : 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : A~Z : Green Package SOT553 Identification Code KR Package Outline Dimensions (All Dimensions in mm) (1) Package Type: SOT553 1.50/1.70 1.0Typ. 0.10/0.18 0.32/0.58 Pin1 0.5Typ. 2.2 C L 1.2 C L 1.7 0.1 6°~8 ° CL 5x-0.5 0.30 C D 0.45/0.67 1.10/1.25 CL A 0.30 C 1.55/1.70 D 0.30 C D 1.0Typ. Hall Sensor 0.15/0.30(5x) 0.10 M C A-B D B 0.55/0.62 6°~8° Pin1 0.5Typ. 0.3 Land Pattern Recommendation (Unit:mm) Top View 6°~ 8° AH1884 Document number: DS31171 Rev. 6 - 2 6 of 7 www.diodes.com September 2010 © Diodes Incorporated AH1884 MICROPOWER, ULTRA-SENSITIVE HALL EFFECT SWITCH IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2010, Diodes Incorporated www.diodes.com AH1884 Document number: DS31171 Rev. 6 - 2 7 of 7 www.diodes.com September 2010 © Diodes Incorporated