DSC2033 Low-Jitter Configurable Dual LVDS Oscillator General Description Features The DSC2033 series of high performance dual output LVDS oscillators utilize a proven silicon MEMS technology to provide excellent jitter and stability while incorporating additional device functionality. The two outputs are controlled by separate supply voltages to allow for high output isolation. The frequencies of the outputs can be identical or independently derived from a common PLL frequency source. The DSC2033 has provision for up to eight userdefined pre-programmed, pin-selectable output frequency combinations. Low RMS Phase Jitter: <1 ps (typ) DSC2033 is packaged in a 14-pin 3.2x2.5 mm QFN package and available in temperature grades from Ext. Commercial to Industrial. Wide Freq. Range: o LVDS output: 2.3 – 460 MHz High Stability: ±10, ±25, ±50 ppm Wide Temperature Range o Industrial: -40° to 85° C o Ext. commercial: -20° to 70° C High Supply Noise Rejection: -50 dBc Two Independent LVDS Outputs Pin-Selectable Configurations o 3-bit Output Frequency Combinations Short Lead Times: 2 Weeks Miniature Footprint of 3.2x2.5mm Excellent Shock & Vibration Immunity o Qualified to MIL-STD-883 High Reliability o 20x better MTF than quartz oscillators Block Diagram Supply Range of 2.25 to 3.6 V Lead Free & RoHS Compliant Applications Storage Area Networks o SATA, SAS, Fibre Channel Passive Optical Networks o EPON, 10G-EPON, GPON, 10G-PON Ethernet o 1G, 10GBASE-T/KR/LR/SR, and FCoE HD/SD/SDI Video & Surveillance PCI Express _____________________________________________________________________________________________________________________________ _________________ DSC2033 Page 1 MK-Q-B-P-D-12042609-2 DSC2033 Low-Jitter Configurable Dual LVDS Oscillator Pin Description Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Pin Name Enable NC NC GND FS0 FS1 FS2 Output1+ Output1Output 2Output 2+ VDD2 VDD NC Pin Type I NA NA Power I I I O O O O Power Power NA Description Enables outputs when high and disables when low Leave unconnected or grounded Leave unconnected or grounded Ground Least significant bit for frequency selection Middle bit for frequency selection Most significant bit for frequency selection Positive LVDS Output 1 Negative LVDS Output 1 Negative LVDS Output 2 Positive LVDS Output 2 Power Supply 2 for LVDS Output 2 Power Supply Leave unconnected or grounded Operational Description The DSC2033 is a dual output LVDS oscillator consisting of a MEMS resonator and a support PLL IC. The two outputs are generated through independent 8-bit programmable dividers from the output of the internal PLL. Two constraints are imposed on the output frequencies: 1) f2=M x f1/N, where M and N are even integers between 4 and 254, 2) 1.2GHz < N x f2 < 1.7GHz. coefficients required by the PLL for up to eight different frequency combinations. Three control pins (FS0 – FS2) select the output frequency combination. Discera supports customer defined versions of the DSC2033. Standard frequency options are described in in the following sections. When Enable (pin 1) is floated or connected to VDD, the DSC2033 is in operational mode. Driving Enable to ground will tri-state both output drivers (hi-impedance mode). The actual frequencies output by the DSC2033 are controlled by an internal pre-programmed memory (OTP). This memory stores all Output Clock Frequencies Table 1 lists the standard frequency configurations and the associated ordering information to be used in conjunction with the ordering code above. Customer defined combinations are available. Table 1. Pre-programmed pin-selectable output frequency combinations Ordering Info G0001 G0002 GXXXX Freq (MHz) Freq Select Bits [FS2, FS1, FS0] – Default is [111] 000 148.5 001 156.25 010 150 011 125 100 125 101 100 110 100 111 400 fOUT2 fOUT1 74.25 125 125 25 50 50 75 200 100 125 0 0 0 0 0 0 fOUT1 100 125 0 0 0 0 0 0 fOUT1 fOUT1 fOUT2 Contact factory for additional configurations. Frequency select bit are weakly tied high so if left unconnected the default setting will be [1] and the device will output the associated frequency highlighted in Bold. _____________________________________________________________________________________________________________________________ _________________ DSC2033 Page 2 MK-Q-B-P-D-12042609-2 DSC2033 Low-Jitter Configurable Dual LVDS Oscillator Absolute Maximum Ratings Item Min Max Unit Supply Voltage -0.3 +4.0 V Input Voltage Junction Temp Storage Temp Soldering Temp ESD HBM MM CDM -0.3 -55 - VDD+0.3 +150 +150 +260 V °C °C °C V Ordering Code Condition Temp Range E: -20 to 70 I: -40 to 85 DSC2033 F I 2 40sec max. Package F: 3.2x2.5mm 4000 400 1500 - xxxxx Stability 1: ±50ppm 2: ±25ppm 5: ±10ppm Packing T: Tape & Reel : Tube T Freq (MHz) See Freq. table Note: 1000+ years of data retention on internal memory Specifications (Unless specified otherwise: T=25° C) Parameter Supply Voltage Condition 1 VDD Supply Current Supply Current IDD 2 IDD Frequency Stability Δf Aging Startup Time3 Input Logic Levels Input logic high Input logic low Δf tSU VIH VIL Output Disable Time4 Output Enable Time Min. Typ. 2.25 EN pin low – outputs are disabled EN pin high – outputs are enabled RL=100Ω, FO1=FO2 =156.25 MHz Includes frequency variations due to initial tolerance, temp. and power supply voltage 1 year @25°C T=25°C 21 Max. Unit 3.6 V 23 mA 38 mA ±10 ±25 ±50 ±5 5 ppm ms 0.25xVDD V tDA 5 ns tEN 20 ns 2 Pull-Up Resistor 0.75xVDD - ppm Pull-up exists on all digital IO 40 kΩ LVDS Outputs Output Offset Voltage R=100Ω Differential 1.125 Delta Offset Voltage Pk to Pk Output Swing Output Transition time Rise Time Fall Time 4 Frequency tR tF Single-Ended 350 20% to 80% RL=100Ω, CL= 2pF (to GND) 200 1.4 V 50 mV mV 350 ps f0 Single Frequency 2.3 460 MHz SYM Differential 48 52 % Period Jitter JPER FO1=FO2=156.25 MHz 2.5 Integrated Phase Noise JCC 200kHz to 20MHz @156.25MHz 100kHz to 20MHz @156.25MHz 12kHz to 20MHz @156.25MHz 0.28 0.4 1.7 Output Duty Cycle 5 Notes: 1. 2. 3. 4. 5. psRMS 2 psRMS Pin 4 VDD should be filtered with 0.01uf capacitor. Output is enabled if Enable pad is floated or not connected. tsu is time to 100PPM stable output frequency after VDD is applied and outputs are enabled. Output Waveform and Test Circuit figures below define the parameters. Period Jitter includes crosstalk from adjacent output. _____________________________________________________________________________________________________________________________ _________________ DSC2033 Page 3 MK-Q-B-P-D-12042609-2 DSC2033 Low-Jitter Configurable Dual LVDS Oscillator Nominal Performance Parameters (Unless specified otherwise: T=25° C, VDD=3.3 V) 2.5 Phase Jitter (ps RMS) 156MHz-LVDS 212MHz-LVDS 2.0 320MHz-LVDS 1.5 410MHz-LVDS 1.0 0.5 0.0 0 200 400 600 800 1000 Low-end of integration BW: x kHz to 20 MHz LVDS Phase jitter (integrated phase noise) Output Waveform: LVDS tR Output tF 80% 350 830 mvmV 50% Output 20% tEN 1/f o tDA VIH Enable VIL _____________________________________________________________________________________________________________________________ _________________ DSC2033 Page 4 MK-Q-B-P-D-12042609-2 DSC2033 Low-Jitter Configurable Dual LVDS Oscillator Solder Reflow Profile 20-40 Sec Se 3C / 217°C 200°C 60-150 Sec . ax cM Se 3C / 25°C a x. Reflow 60-180 Sec cM 150°C Se 6C/ Temperature (°C) cM ax . 260°C Cool Pre heat Time 8 min max MSL 1 @ 260°C refer to JSTD-020C Ramp-Up Rate (200°C to Peak Temp) 3°C/Sec Max. Preheat Time 150°C to 200°C 60-180 Sec Time maintained above 217°C 60-150 Sec 255-260°C Peak Temperature Time within 5°C of actual Peak 20-40 Sec 6°C/Sec Max. Ramp-Down Rate Time 25°C to Peak Temperature 8 min Max. Package Dimensions 3.2 x 2.5 mm 14 Lead Plastic Package Disclaimer: Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. MICREL, Inc. Phone: +1 (408) 944-0800 ● ● 2180 Fortune Drive, Fax: +1 (408) 474-1000 San Jose, California 95131 ● Email: [email protected] ● ● USA www.micrel.com _____________________________________________________________________________________________________________________________ _________________ DSC2033 Page 5 MK-Q-B-P-D-12042609-2