Features • 80C52 Compatible • • • • • • • • • • • • • • • • • • • – Four 8-bit I/O Ports – Three 16-bit Timer/Counters – 256 Bytes Scratch Pad RAM – 8 Interrupt Sources with 4 Priority Levels – Dual Data Pointer Variable Length MOVX for Slow RAM/Peripherals High-speed Architecture – 10 to 40 MHz in Standard Mode 16K/32K Bytes On-Chip ROM Program T80C51RD2 ROMless Versions On-Chip 1024 bytes Expanded RAM (XRAM) – Software Selectable Size (0, 256, 512, 768, 1024 bytes) – 256 Bytes Selected at Reset for AT87C51RB2/RC2 Compatibility Keyboard Interrupt Interface on Port P1 8-bit Clock Prescaler 64K Program and Data Memory Spaces Improved X2 Mode with Independant Selection for CPU and Each Peripheral Programmable Counter Array 5 Channels with: – High-speed Output – Compare/Capture – Pulse Width Modulator – Watchdog Timer Capabilities Asynchronous Port Reset Full Duplex Enhanced UART Dedicated Baud Rate Generator for UART Low EMI (Inhibit ALE) Hardware Watchdog Timer (One-time Enabled with Reset-out) Power Control Modes – Idle Mode – Power-down Mode – Power-off Flag Power Supply: 2.7V to 5.5V or 2.7V to 3.6V Temperature Ranges: Commercial (0 to +70°C) and Industrial (-40°C to +85°C) Packages: PDIL40, PLCC44, VQFP44 80C51 High Performance ROM 8-bit Microcontroller AT80C51RD2 AT83C51RB2 AT83C51RC2 Description AT8xC51Rx2 microcontrollers are high performance ROM versions of the 80C51 8-bit microcontrollers. They contain a 0K, 16K or 32K bytes ROM memory block for program. The microcontrollers retain all features of the Atmel 80C52 with 256 bytes of internal RAM, a 7-source 4-level interrupt controller and three timer/counters. In addition, the microcontrollers have a Programmable Counter Array, an XRAM of 1024 byte, a Hardware Watchdog Timer, a Keyboard Interface, a more versatile serial channel that facilitates multiprocessor communication (EUART) and a speed improvement mechanism (X2 mode). The microcontrollers have 2 software-selectable modes of reduced activity and 8 bit clock prescaler for further reduction in power consumption. In Idle mode, the CPU is frozen while the peripherals and the interrupt system are still operating. In the Powerdown mode, the RAM is saved and all other functions are inoperative. Rev. 4113B–8051–03/05 Table 1. Memory Size ROM (Bytes) XRAM (Bytes) TOTAL RAM (Bytes) I/O AT83C51RB2 16K 1024 1280 32 AT83C51RC2 32K 1024 1280 32 AT80C51RD2 ROMless 1024 1280 32 (2) (2) XTAL1 XTAL2 RAM 256x8 C51 CORE PSEN ROM 32Kx8 or 16Kx8 XRAM PCA 1Kx8 T2 T2EX (1) (1) (1) EUART + BRG ALE/ PROG PCA ECI Vss VCC TxD RxD Block Diagram (1) Timer2 IB-bus CPU EA Timer 0 Timer 1 (2) Parallel I/O Ports & Ext. Bus Watch Dog Key Board P3 P2 P1 P0 INT0 INT1 (2) (2) T1 (2) (2) Notes: 2 INT Ctrl Port 0 Port 1 Port 2 Port 3 RESET WR (2) T0 RD 1. Alternate function of Port 1 2. Alternate function of Port 3 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Pin Configurations P1.0/T2 1 40 VCC P1.1/T2EX 2 P0.0/AD0 P1.2/ECI P1.3CEX0 P1.4/CEX1 3 4 39 38 P1.5/CEX2 P1.6/CEX3 6 7 8 9 37 P0.1/AD1 P0.2/AD2 36 35 P0.3/AD3 P0.4/AD4 34 33 P0.5/AD5 32 P0.7/AD7 31 30 EA ALE/PROG 13 29 28 P3.5/T1 14 15 27 26 PSEN P2.7/AD15 P2.6/AD14 P2.5/AD13 P3.6/WR 16 25 P3.7/RD XTAL2 17 18 19 20 24 XTAL1 VSS 23 22 21 P2.1/AD9 P0.2/AD2 P0.3/AD3 P0.1/AD1 P0.0/AD0 VCC NIC* P1.0/T2 6 5 4 3 2 1 44 43 42 41 40 P2.4/AD12 P2.3/AD11 P2.2/AD10 P1.1/T2EX P3.4/T0 PDIL40 11 12 P1.2/ECI P3.2/INT0 P3.3/INT1 10 P1.3/CEX0 P3.0/RxD P3.1/TxD P0.6/AD6 P1.4/CEX1 P1.7CEX4 RST 5 P1.5/CEX2 P2.0/AD8 39 38 P0.4/AD4 P1.6/CEX3 7 8 P1.7/CEx4 9 37 P0.6/AD6 RST 10 36 P0.7/AD7 P3.0/RxD 11 12 13 35 34 33 EA 14 15 32 31 PSEN 16 30 P2.6/A14 17 29 P2.5/A13 NIC* P3.1/TxD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 PLCC44 P0.5/AD5 NIC* ALE/PROG P2.7/A15 P2.3/A11 P2.4/A12 P2.2/A10 P2.1/A9 NIC* P2.0/A8 VSS XTAL1 XTAL2 P3.7/RD P3.6/WR P0.3/AD3 P0.2/AD2 P0.1/AD1 P0.0/AD0 VCC NIC* P1.0/T2 P1.1/T2EX P1.2/ECI P1.3/CEX0 P1.4/CEX1 18 19 20 21 22 23 24 25 26 27 28 44 43 42 41 40 39 38 37 36 35 34 33 32 P0.4/AD4 31 P0.6/AD6 30 P0.7/AD7 29 28 27 EA PSEN 9 26 25 10 24 P2.6/A14 11 23 P2.5/A13 P1.5/CEX2 1 P1.6/CEX3 P1.7/CEX4 2 RST P3.0/RxD NIC* P3.1/TxD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 3 4 5 VQFP44 1.4 6 7 8 P0.5/AD5 NIC* ALE/PROG P2.7/A15 P2.3/A11 P2.4/A12 P2.2/A10 P2.1/A9 NIC* P2.0/A8 VSS XTAL1 XTAL2 P3.7/RD P3.6/WR 12 13 14 15 16 17 18 19 20 21 22 *NIC: No Internal Connection 3 4113B–8051–03/05 Table 2. Pin Description Pin Number Mnemonic DIL PLCC44 VQFP44 1.4 Type Name and Function VSS 20 22 16 I Ground: 0V reference VCC 40 44 38 I Power Supply: This is the power supply voltage for normal, idle and power-down operation P0.0 - P0.7 39 - 32 43 - 36 37 - 30 I/O Port 0: Port 0 is an open-drain, bi-directional I/O port. Port 0 pins that have 1s written to them float and can be used as high impedance inputs. Port 0 must be polarized to VCC or VSS in order to prevent any parasitic current consumption. Port 0 is also the multiplexed low-order address and data bus during access to external program and data memory. In this application, it uses strong internal pull-up when emitting 1s. Port 0 also inputs the code bytes during EPROM programming. External pull-ups are required during program verification during which P0 outputs the code bytes. P1.0 - P1.7 1-8 2-9 40 - 44 1-3 I/O Port 1: Port 1 is an 8-bit bi-directional I/O port with internal pull-ups. Port 1 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 1 pins that are externally pulled low will source current because of the internal pull-ups. Port 1 also receives the low-order address byte during memory programming and verification. Alternate functions for T89C51RB2/RC2 Port 1 include: 1 2 2 3 40 41 I/O P1.0: Input/Output I/O T2 (P1.0): Timer/Counter 2 external count input/Clockout I/O P1.1: Input/Output I 3 4 42 I/O I 4 5 6 7 8 5 6 7 8 9 43 44 1 2 3 T2EX: Timer/Counter 2 Reload/Capture/Direction Control P1.2: Input/Output ECI: External Clock for the PCA I/O P1.3: Input/Output I/O CEX0: Capture/Compare External I/O for PCA module 0 I/O P1.4: Input/Output I/O CEX1: Capture/Compare External I/O for PCA module 1 I/O P1.5: Input/Output I/O CEX2: Capture/Compare External I/O for PCA module 2 I/O P1.6: Input/Output I/O CEX3: Capture/Compare External I/O for PCA module 3 I/O P1.7: Input/Output: I/O CEX4: Capture/Compare External I/O for PCA module 4 XTAL1 19 21 15 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits. XTAL2 18 20 14 O Crystal 2: Output from the inverting oscillator amplifier 4 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 2. Pin Description (Continued) Pin Number Mnemonic DIL PLCC44 VQFP44 1.4 Type P2.0 - P2.7 21 - 28 24 - 31 18 - 25 I/O Name and Function Port 2: Port 2 is an 8-bit bi-directional I/O port with internal pull-ups. Port 2 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally pulled low will source current because of the internal pull-ups. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it uses strong internal pull-ups emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX @Ri), Port 2 emits the contents of the P2 SFR. Some Port 2 pins receive the high order address bits during ROM reading and verification: P2.0 to P2.5 for 16 KB devices P2.0 to P2.6 for 32 KB devices P3.0 - P3.7 10 - 17 11, 13 - 19 5, 7 - 13 I/O Port 3: Port 3 is an 8-bit bi-directional I/O port with internal pull-ups. Port 3 pins that have 1s written to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally pulled low will source current because of the internal pull-ups. Port 3 also serves the special features of the 80C51 family, as listed below. 10 11 5 I RXD (P3.0): Serial input port 11 13 7 O TXD (P3.1): Serial output port 12 14 8 I INT0 (P3.2): External interrupt 0 13 15 9 I INT1 (P3.3): External interrupt 1 14 16 10 I T0 (P3.4): Timer 0 external input 15 17 11 I T1 (P3.5): Timer 1 external input 16 18 12 O WR (P3.6): External data memory write strobe 17 19 13 O RD (P3.7): External data memory read strobe Reset: A high on this pin for two machine cycles while the oscillator is running, resets the device. An internal diffused resistor to VSS permits a power-on reset using only an external capacitor to VCC. This pin is an output when the hardware watchdog forces a system reset. RST 9 10 4 I/O ALE/PROG 30 33 27 O (I) Address Latch Enable/Program Pulse: Output pulse for latching the low byte of the address during an access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6 (1/3 in X2 mode) the oscillator frequency, and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory. This pin is also the program pulse input (PROG) during Flash programming. ALE can be disabled by setting SFR’s AUXR.0 bit. With this bit set, ALE will be inactive during internal fetches. PSEN 29 32 26 O Program Strobe Enable: The read strobe to external program memory. When executing code from the external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. PSEN is not activated during fetches from internal program memory. EA 31 35 29 I External Access Enable: EA must be externally held low to enable the device to fetch code from external program memory locations 0000H to 3FFFH (16K), 7FFFH (32K). If security level 1 is programmed, EA will be internally latched on Reset. 5 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 SFR Mapping The Special Function Registers (SFRs) of the microcontroller fall into the following categories: • C51 core registers: ACC, B, DPH, DPL, PSW, SP • I/O port registers: P0, P1, P2, P3 • Timer registers: T2CON, T2MOD, TCON, TH0, TH1, TH2, TMOD, TL0, TL1, TL2, RCAP2L, RCAP2H • Serial I/O port registers: SADDR, SADEN, SBUF, SCON • PCA (Programmable Counter Array) registers: CCON, CCAPMx, CL, CH, CCAPxH, CCAPxL (x: 0 to 4) • Power and clock control registers: PCON • Hardware Watchdog Timer registers: WDTRST, WDTPRG • Interrupt system registers: IE0, IPL0, IPH0, IE1, IPL1, IPH1 • Keyboard Interface registers: KBE, KBF, KBLS • BRG (Baud Rate Generator) registers: BRL, BDRCON • Clock Prescaler register: CKRL • Others: AUXR, AUXR1, CKCON0, CKCON1 7 4113B–8051–03/05 Table 3 shows all SFRs with their address and their reset value. Table 3. SFR Mapping Bit Addressable 0/8 F8h F0h D8h 1/9 2/A 3/B 4/C 5/D 6/E CH CCAP0H CCAP1H CCAPL2H CCAPL3H CCAPL4H 0000 0000 XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX 7/F FFh B 0000 0000 E8h E0h Non-bit Addressable F7h CL CCAP0L CCAP1L CCAPL2L CCAPL3L CCAPL4L 0000 0000 XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX EFh ACC 0000 0000 E7h CCON CMOD CCAPM0 CCAPM1 CCAPM2 CCAPM3 CCAPM4 00X0 0000 00XX X000 X000 0000 X000 0000 X000 0000 X000 0000 X000 0000 D0h PSW 0000 0000 C8h T2CON 0000 0000 DFh D7h T2MOD XXXX XX00 RCAP2L 0000 0000 RCAP2H 0000 0000 TL2 0000 0000 TH2 0000 0000 CFh C0h B8h B0h A8h A0h 98h 90h 88h 80h C7h IPL0 SADEN X000 000 0000 0000 BFh P3 IE1 IPL1 IPH1 IPH0 1111 1111 XXXX XXX0b XXXX XXX0b XXXX XXX0b X000 0000 IE0 SADDR 0000 0000 0000 0000 B7h AFh P2 AUXR1 WDTRST WDTPRG 1111 1111 XXXX XXX0 XXXX XXXX XXXX X000 SCON SBUF BRL BDRCON KBLS KBE KBF 0000 0000 XXXX XXXX 0000 0000 XXX0 0000 0000 0000 0000 0000 0000 0000 9Fh P1 CKRL 1111 1111 1111 1111 TCON TMOD TL0 TL1 TH0 TH1 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 P0 1111 1111 SP 0000 0111 DPL 0000 0000 DPH 0000 0000 0/8 1/9 2/A 3/B AUXR XX0X 0000 A7h CKCON0 97h 8Fh 0000 0000 PCON 87h 00X1 0000 4/C 5/D 6/E 7/F Reserved 8 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Oscillators Overview One oscillator is available for CPU: • OSC used for high frequency (3 MHz to 40 MHz) In order to optimize the power consumption and the execution time needed for a specific task, an internal prescaler feature has been implemented between the selected oscillator and the CPU. Registers Table 4. Clock Reload Register 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7:0 Bit Mnemonic Description CKRL Clock Reload Register: Prescaler value Reset Value = 1111 1111b Not bit addressable Prescaler Divider A hardware RESET puts the prescaler divider in the following state: • CKRL = FFh: FCLK CPU = FCLK PERIPH = FOSC/2 (Standard C51 feature) KS signal selects OSC: FCLK OUT = FOSC • Any value between FFh down to 00h can be written by software into CKRL register in order to divide frequency of the selected oscillator: – CKRL = 00h: minimum frequency FCLK CPU = FCLK PERIPH = FOSC/1020 (Standard Mode) FCLK CPU = FCLK PERIPH = FOSC/510 (X2 Mode) – CKRL = FFh: maximum frequency FCLK CPU = FCLK PERIPH = FOSC/2 (Standard Mode) FCLK CPU = FCLK PERIPH = FOSC (X2 Mode) – FCLK CPU and FCLK PERIPH In X2 mode: F OSC F CPU = F CLKPERIPH = --------------------------------------------- 2 × ( 255 – CKRL ) In X1 mode: F OSCA F CPU = F CLKPERIPH = --------------------------------------------- 4 × ( 255 – CKRL ) 9 4113B–8051–03/05 Enhanced Features X2 Feature and OSC Clock Generation In comparison to the original 80C52, the microcontrollers implement the following new features: • X2 option • Dual Data Pointer • Extended RAM • Programmable Counter Array (PCA) • Hardware Watchdog • 4-level Interrupt Priority System • Power-off Flag • Power On Reset • ONCE mode • ALE disabling • Some enhanced features are also located in the UART and the Timer 2 The microcontroller core needs only 6 clock periods per machine cycle. This feature called ”X2” provides the following advantages: • Divides frequency crystals by 2 (cheaper crystals) while keeping same CPU power. • Saves power consumption while keeping same CPU power (oscillator power saving). • Saves power consumption by dividing dynamically the operating frequency by 2 in operating and idle modes. • Increases CPU power by 2 while keeping same crystal frequency. In order to keep the original C51 compatibility, a divider by 2 is inserted between the XTAL1 signal and the main clock input of the core (phase generator). This divider may be disabled by software. Description The clock for the whole circuit and peripherals is first divided by two before being used by the CPU core and the peripherals. This allows any cyclic ratio to be accepted on XTAL1 input. In X2 mode, as this divider is bypassed, the signals on XTAL1 must have a cyclic ratio between 40 to 60%. Figure 2 shows the clock generation block diagram. X2 bit is validated on the rising edge of the XTAL1 ÷ 2 to avoid glitches when switching from X2 to standard mode. Figure 3 shows the switching mode waveforms. Figure 2. Clock Generation Diagram CKRL 2 XTAL1 FXTAL FOSC XTAL1:2 0 1 CLK Periph 8-bit Prescaler Idle CLK CPU X2 CKCON0 10 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Figure 3. Mode Switching Waveforms XTAL1 XTAL1:2 X2 Bit FOSC CPU Block STD Mode X2 Mode STD Mode The X2 bit in the CKCON0 register (see Table 5) allows to switch from 12 clock periods per instruction to 6 clock periods and vice versa. At reset, the speed is set according to X2 bit of Hardware Config Byte (HCB). By default, Standard mode is activated. Setting the X2 bit activates the X2 feature (X2 mode). The T0X2, T1X2, T2X2, UARTX2, PCAX2 and WDX2 bits in the CKCON0 register (Table 5) allow to switch from standard peripheral speed (12 clock periods per peripheral clock cycle) to fast peripheral speed (6 clock periods per peripheral clock cycle). These bits are active only in X2 mode. 11 4113B–8051–03/05 Table 5. CKCON0 Register CKCON0 - Clock Control Register (8Fh) 7 6 5 4 3 2 1 0 - WDX2 PCAX2 SIX2 T2X2 T1X2 T0X2 X2 Bit Bit Number Mnemonic 7 - 6 WDX2 Description Reserved Do not set this bit. Watchdog clock (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 5 PCAX2 Programmable Counter Array clock (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 4 SIX2 Enhanced UART clock (Mode 0 and 2) (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 3 T2X2 Timer 2 clock (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. 2 T1X2 Timer 1 clock (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle 1 T0X2 Timer 0 clock (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle CPU clock Cleared to select 12 clock periods per machine cycle (STD mode) for CPU and all the peripherals. 0 X2 Set to select 6clock periods per machine cycle (X2 mode) and to enable the individual peripherals "X2" bits. Programmed by hardware after Power-up regarding Hardware Config Byte (HCB). Reset Value = 0000 000’HCB.X2’b (see Hardware Config Byte) Not bit addressable 12 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Dual Data Pointer Register The additional data pointer can be used to speed up code execution and reduce code size. The dual DPTR structure is a way by which the chip will specify the address of an external data memory location. There are two 16-bit DPTR registers that address the external memory, and a single bit called DPS = AUXR1.0 (see Table 6) that allows the program code to switch between them (Refer to Figure 4). Figure 4. Use of Dual Pointer External Data Memory 7 0 DPS DPTR1 DPTR0 AUXR1(A2H) DPH(83H) DPL(82H) Table 6. AUXR1 Register AUXR1- Auxiliary Register 1(0A2h) 7 6 5 4 3 2 1 0 - - - - GF3 0 - DPS Bit Number Bit Mnemonic 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 GF3 2 0 Always cleared(1). 1 - Reserved The value read from this bit is indeterminate. Do not set this bit. 0 DPS Description This bit is a general purpose user flag. Data Pointer Selection Cleared to select DPTR0. Set to select DPTR1. Reset Value: XXXX XXXX0b Not bit addressable Note: 1. Bit 2 stuck at 0; this allows to use INC AUXR1 to toggle DPS without changing GF3. 13 4113B–8051–03/05 Assembly Language ; Block move using dual data pointers ; Modifies DPTR0, DPTR1, A and PSW ; note: DPS exits opposite of entry state ; unless an extra INC AUXR1 is added ; 00A2 AUXR1 EQU 0A2H ; 0000 909000MOV DPTR,#SOURCE ; address of SOURCE 0003 05A2 INC AUXR1 ; switch data pointers 0005 90A000 MOV DPTR,#DEST ; address of DEST 0008 LOOP: 0008 05A2 INC AUXR1 ; switch data pointers 000A E0 MOVX A,@DPTR ; get a byte from SOURCE 000B A3 INC DPTR ; increment SOURCE address 000C 05A2 INC AUXR1 ; switch data pointers 000E F0 MOVX @DPTR,A ; write the byte to DEST 000F A3 INC DPTR ; increment DEST address 0010 70F6JNZ LOOP ; check for 0 terminator 0012 05A2 INC AUXR1 ; (optional) restore DPS INC is a short (2 bytes) and fast (12 clocks) way to manipulate the DPS bit in the AUXR1 SFR. However, note that the INC instruction does not directly force the DPS bit to a particular state, but simply toggles it. In simple routines, such as the block move example, only the fact that DPS is toggled in the proper sequence matters, not its actual value. In other words, the block move routine works the same whether DPS is '0' or '1' on entry. Observe that without the last instruction (INC AUXR1), the routine will exit with DPS in the opposite state. 14 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Expanded RAM (XRAM) The T8xc51Rx2 devices provide additional Bytes of Random Access Memory (RAM) space for increased data parameter handling and high level language usage. The devices have expanded RAM in external data space; maximum size and location are described in Table 7. Table 7. Expanded RAM Address XRAM size Start End 1024 00h 3FFh T83C51RB2/RC2 T80C51RD2 The T8xc51Rx2 has internal data memory that is mapped into four separate segments. The four segments are: 1. The Lower 128 bytes of RAM (addresses 00h to 7Fh) are directly and indirectly addressable. 2. The Upper 128 bytes of RAM (addresses 80h to FFh) are indirectly addressable only. 3. The Special Function Registers (SFRs) (addresses 80h to FFh) are directly addressable only. 4. The expanded RAM bytes are indirectly accessed by MOVX instructions, and with the EXTRAM bit cleared in the AUXR register (see Table 7). The lower 128 bytes can be accessed by either direct or indirect addressing. The Upper 128 bytes can be accessed by indirect addressing only. The Upper 128 bytes occupy the same address space as the SFR. That means they have the same address, but are physically separate from SFR space. Figure 5. Internal and External Data Memory Address 0FFh or 3FFh 0FFh Upper 128 Bytes Internal RAM indirect accesses XRAM 0FFFFh 0FFh 80h Special Function Register Direct Accesses External Data Memory 80h 7Fh Lower 128 Bytes Internal RAM Direct or Indirect Accesses 00 00 00FFh up to 03FFh 0000 15 4113B–8051–03/05 When an instruction accesses an internal location above address 7Fh, the CPU knows whether the access is to the upper 128 bytes of data RAM or to SFR space by the addressing mode used in the instruction. • Instructions that use direct addressing access SFR space. For example: MOV 0A0H, # data, accesses the SFR at location 0A0h (which is P2). • Instructions that use indirect addressing access the Upper 128 bytes of data RAM. For example: MOV @R0, # data where R0 contains 0A0h, accesses the data byte at address 0A0h, rather than P2 (whose address is 0A0h). • The XRAM bytes can be accessed by indirect addressing, with EXTRAM bit cleared and MOVX instructions. This part of memory which is physically located on-chip, logically occupies the first bytes of external data memory. The bits XRS0 and XRS1 are used to hide a part of the available XRAM as explained in Table 7. This can be useful if external peripherals are mapped at addresses already used by the internal XRAM. • With EXTRAM = 0, the XRAM is indirectly addressed, using the MOVX instruction in combination with any of the registers R0, R1 of the selected bank or DPTR. An access to XRAM will not affect ports P0, P2, P3.6 (WR) and P3.7 (RD). For example, with EXTRAM = 0, MOVX @R0, # data where R0 contains 0A0H, accesses the XRAM at address 0A0H rather than external memory. An access to external data memory locations higher than the accessible size of the XRAM will be performed with the MOVX DPTR instructions in the same way as in the standard 80C51, with P0 and P2 as data/address busses, and P3.6 and P3.7 as write and read timing signals. Accesses to XRAM above 0FFH can only be done by the use of DPTR. • With EXTRAM = 1, MOVX @Ri and MOVX @DPTR will be similar to the standard 80C51. MOVX @ Ri will provide an eight-bit address multiplexed with data on Port 0 and any output port pins can be used to output higher order address bits. This is to provide the external paging capability. MOVX @DPTR will generate a sixteen-bit address. Port2 outputs the high-order eight address bits (the contents of DPH) while Port0 multiplexes the low-order eight address bits (DPL) with data. MOVX @ Ri and MOVX @DPTR will generate either read or write signals on P3.6 (WR) and P3.7 (RD). The stack pointer (SP) may be located anywhere in the 256 bytes RAM (lower and upper RAM) internal data memory. The stack may not be located in the XRAM. The M0 bit allows to stretch the XRAM timings; if M0 is set, the read and write pulses are extended from 6 to 30 clock periods. This is useful to access external slow peripherals. 16 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 8. AUXR Register AUXR - Auxiliary Register (8Eh) 7 6 5 4 3 2 1 0 - - M0 - XRS1 XRS0 EXTRAM AO Bit Number Bit Mnemonic Description 7 - 6 - 5 M0 Reserved The value read from this bit is indeterminate. Do not set this bit Reserved The value read from this bit is indeterminate. Do not set this bit Pulse length Cleared to stretch MOVX control: the RD and the WR pulse length is 6 clock periods (default). Set to stretch MOVX control: the RD and the WR pulse length is 30 clock periods. Reserved 4 - 3 XRS1 XRAM Size 2 XRS0 XRS1 0 XRS0 0 XRAM Size 256 bytes (default) 0 1 512 bytes 1 0 768 bytes 1 1 1024 bytes 1 EXTRAM The value read from this bit is indeterminate. Do not set this bit EXTRAM bit Cleared to access internal XRAM using MOVX @ Ri/ @ DPTR. Set to access external memory. Programmed by hardware after Power-up regarding Hardware Security Byte (HSB), default setting, XRAM selected. 0 AO ALE Output bit Cleared, ALE is emitted at a constant rate of 1/6 the oscillator frequency (or 1/3 if X2 mode is used) (default). Set, ALE is active only if a MOVX or MOVC instruction is used. Reset Value = XX0X 00’HSB.XRAM’0b (see Table 7) Not bit addressable 17 4113B–8051–03/05 Timer 2 The Timer 2 in the T8xc51Rx2 is the standard C52 Timer 2. It is a 16-bit timer/counter: the count is maintained by two eight-bit timer registers, TH2 and TL2 are cascaded. It is controlled by T2CON (Table 9) and T2MOD (Table 10) registers. Timer 2 operation is similar to Timer 0 and Timer 1. C/T2 selects FOSC/12 (timer operation) or external pin T2 (counter operation) as the timer clock input. Setting TR2 allows TL2 to be incremented by the selected input. Timer 2 has 3 operating modes: capture, auto-reload and Baud Rate Generator. These modes are selected by the combination of RCLK, TCLK and CP/RL2 (T2CON). Refer to the Atmel 8-bit Microcontroller Hardware description for Capture and Baud Rate Generator Modes. Timer 2 includes the following enhancements: Auto-reload Mode • Auto-reload mode with up or down counter • Programmable clock-output The auto-reload mode configures Timer 2 as a 16-bit timer or event counter with automatic reload. If DCEN bit in T2MOD is cleared, Timer 2 behaves as in 80C52 (refer to the Atmel 8-bit Microcontroller Hardware description). If DCEN bit is set, Timer 2 acts as an Up/down timer/counter as shown in Figure 6. In this mode the T2EX pin controls the direction of count. When T2EX is high, Timer 2 counts up. Timer overflow occurs at FFFFh which sets the TF2 flag and generates an interrupt request. The overflow also causes the 16-bit value in RCAP2H and RCAP2L registers to be loaded into the timer registers TH2 and TL2. When T2EX is low, Timer 2 counts down. Timer underflow occurs when the count in the timer registers TH2 and TL2 equals the value stored in RCAP2H and RCAP2L registers. The underflow sets TF2 flag and reloads FFFFh into the timer registers. The EXF2 bit toggles when Timer 2 overflows or underflows according to the direction of the count. EXF2 does not generate any interrupt. This bit can be used to provide 17-bit resolution. 18 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Figure 6. Auto-Reload Mode Up/Down Counter (DCEN = 1) FCLK PERIPH :6 0 1 T2 C/T2 TR2 T2CON T2CON T2EX: (DOWN COUNTING RELOAD VALUE) if DCEN = 1, 1 = UP FFh FFh if DCEN = 1, 0 = DOWN (8-bit) (8-bit) if DCEN = 0, up counting TOGGLE T2CON EXF2 TL2 (8-bit) TH2 (8-bit) TF2 TIMER 2 INTERRUPT T2CON RCAP2L (8-bit) RCAP2H (8-bit) (UP COUNTING RELOAD VALUE) Programmable ClockOutput In the clock-out mode, Timer 2 operates as a 50% duty-cycle, programmable clock generator (see Figure 7). The input clock increments TL2 at frequency FCLK PERIPH/2. The timer repeatedly counts to overflow from a loaded value. At overflow, the contents of RCAP2H and RCAP2L registers are loaded into TH2 and TL2. In this mode, Timer 2 overflows do not generate interrupts. The formula gives the clock-out frequency as a function of the system oscillator frequency and the value in the RCAP2H and RCAP2L registers: F CLKPERIPH Clock – OutFrequency = ----------------------------------------------------------------------------------------4 × ( 65536 – RCAP2H ⁄ RCAP2L ) For a 16 MHz system clock, Timer 2 has a programmable frequency range of 61 Hz (FCLK PERIPH/216) to 4 MHz (FCLK PERIPH/4). The generated clock signal is brought out to T2 pin (P1.0). Timer 2 is programmed for the clock-out mode as follows: • Set T2OE bit in T2MOD register. • Clear C/T2 bit in T2CON register. • Determine the 16-bit reload value from the formula and enter it in RCAP2H/RCAP2L registers. • Enter a 16-bit initial value in timer registers TH2/TL2. It can be the same as the reload value or a different one depending on the application. • To start the timer, set TR2 run control bit in T2CON register. It is possible to use Timer 2 as a baud rate generator and a clock generator simultaneously. For this configuration, the baud rates and clock frequencies are not independent since both functions use the values in the RCAP2H and RCAP2L registers. 19 4113B–8051–03/05 Figure 7. Clock-Out Mode C/T2 = 07 FCLK PERIPH :6 TR2 T2CON TL2 (8-bit) TH2 (8-bit) OVEFLOW RCAP2L (8-bit) RCAP2H (8-bit) Toggle T2 Q D T2OE T2MOD EXF2 T2EX EXEN2 T2CON 20 TIMER 2 INTERRUPT T2CON AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 9. T2CON Register T2CON - Timer 2 Control Register (C8h) 7 6 5 4 3 2 1 0 TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2# CP/RL2# Bit Bit Number Mnemonic 7 TF2 Description Timer 2 overflow Flag Must be cleared by software. Set by hardware on Timer 2 overflow, if RCLK = 0 and TCLK = 0. 6 EXF2 Timer 2 External Flag Set when a capture or a reload is caused by a negative transition on T2EX pin if EXEN2 = 1. When set, causes the CPU to vector to Timer 2 interrupt routine when Timer 2 interrupt is enabled. Must be cleared by software. EXF2 doesn’t cause an interrupt in Up/down counter mode (DCEN = 1) 5 RCLK Receive Clock bit Cleared to use timer 1 overflow as receive clock for serial port in mode 1 or 3. Set to use Timer 2 overflow as receive clock for serial port in mode 1 or 3. 4 TCLK Transmit Clock bit Cleared to use timer 1 overflow as transmit clock for serial port in mode 1 or 3. Set to use Timer 2 overflow as transmit clock for serial port in mode 1 or 3. 3 EXEN2 2 TR2 1 0 Timer 2 External Enable bit Cleared to ignore events on T2EX pin for Timer 2 operation. Set to cause a capture or reload when a negative transition on T2EX pin is detected, if Timer 2 is not used to clock the serial port. Timer 2 Run control bit Cleared to turn off Timer 2. Set to turn on Timer 2. C/T2# Timer/Counter 2 select bit Cleared for timer operation (input from internal clock system: FCLK PERIPH). Set for counter operation (input from T2 input pin, falling edge trigger). Must be 0 for clock out mode. CP/RL2# Timer 2 Capture/Reload bit If RCLK = 1 or TCLK = 1, CP/RL2# is ignored and timer is forced to auto-reload on Timer 2 overflow. Cleared to auto-reload on Timer 2 overflows or negative transitions on T2EX pin if EXEN2 = 1. Set to capture on negative transitions on T2EX pin if EXEN2 = 1. Reset Value = 0000 0000b Bit addressable 21 4113B–8051–03/05 Table 10. T2MOD Register T2MOD - Timer 2 Mode Control Register (C9h) 7 6 5 4 3 2 1 0 - - - - - - T2OE DCEN Bit Bit Number Mnemonic 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 - Reserved The value read from this bit is indeterminate. Do not set this bit. 1 T2OE Timer 2 Output Enable bit Cleared to program P1.0/T2 as clock input or I/O port. Set to program P1.0/T2 as clock output. 0 DCEN Down Counter Enable bit Cleared to disable Timer 2 as up/down counter. Set to enable Timer 2 as up/down counter. Description Reset Value = XXXX XX00b Not bit addressable 22 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Programmable Counter Array (PCA) The PCA provides more timing capabilities with less CPU intervention than the standard timer/counters. Its advantages include reduced software overhead and improved accuracy. The PCA consists of a dedicated timer/counter which serves as the time base for an array of five compare/capture modules. Its clock input can be programmed to count any one of the following signals: • ÷6 Peripheral clock frequency (FCLK PERIPH) ÷ 2 • Timer 0 overflow • External input on ECI (P1.2) • Peripheral clock frequency (FCLK PERIPH) Each compare/capture modules can be programmed in any one of the following modes: • Rising and/or falling edge capture • Software timer • High-speed output • Pulse width modulator Module 4 can also be programmed as a Watchdog Timer (see Section "PCA Watchdog Timer", page 34). When the compare/capture modules are programmed in the capture mode, software timer, or high-speed output mode, an interrupt can be generated when the module executes its function. All five modules plus the PCA timer overflow share one interrupt vector. The PCA timer/counter and compare/capture modules share Port 1 for external I/O. These pins are listed below. If the port is not used for the PCA, it can still be used for standard I/O. PCA Component External I/O Pin 16-bit Counter P1.2/ECI 16-bit Module 0 P1.3/CEX0 16-bit Module 1 P1.4/CEX1 16-bit Module 2 P1.5/CEX2 16-bit Module 3 P1.6/CEX3 The PCA timer is a common time base for all five modules (see Figure 8). The timer count source is determined from the CPS1 and CPS0 bits in the CMOD register (Table 11) and can be programmed to run at: • 1/6 the peripheral clock frequency (FCLK PERIPH) • 1/2 the peripheral clock frequency (FCLK PERIPH) • The Timer 0 overflow • The input on the ECI pin (P1.2) 23 4113B–8051–03/05 Figure 8. PCA Timer/Counter To PCA Modules FCLK PERIPH /6 Overflow FCLK PERIPH/2 CH T0 OVF It CL 16-Bit Up/Down Counter P1.2 CIDL WDTE CF CR CPS1 CPS0 ECF CMOD 0xD9 CCF2 CCF1 CCF0 CCON 0xD8 Idle 24 CCF4 CCF3 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 11. CMOD Register CMOD - PCA Counter Mode Register (D9h) 7 6 5 4 3 2 1 0 CIDL WDTE - - - CPS1 CPS0 ECF Bit Number Bit Mnemonic Description Counter Idle Control 7 CIDL Cleared to program the PCA Counter to continue functioning during idle Mode. Set to program PCA to be gated off during idle. Watchdog Timer Enable 6 WDTE Cleared to disable Watchdog Timer function on PCA Module 4. Set to enable Watchdog Timer function on PCA Module 4. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 CPS1 PCA Count Pulse Select CPS1 0 1 0 CPS0 ECF CPS0 Selected PCA input 0 Internal clock fCLK PERIPH/6 0 1 1 0 Internal clock fCLK PERIPH/2 Timer 0 Overflow 1 1 External clock at ECI/P1.2 pin (max rate = fCLK PERIPH/4) PCA Enable Counter Overflow Interrupt Cleared to disable CF bit in CCON to inhibit an interrupt. Set to enable CF bit in CCON to generate an interrupt. Reset Value = 00XX X000b Not bit addressable The CMOD register includes three additional bits associated with the PCA (see Figure 11 and Table 11). • The CIDL bit which allows the PCA to stop during idle mode. • The WDTE bit which enables or disables the watchdog function on module 4. • The ECF bit which when set causes an interrupt and the PCA overflow flag CF (in the CCON SFR) to be set when the PCA timer overflows. The CCON register contains the run control bit for the PCA and the flags for the PCA timer (CF) and each module (see Table 12). • Bit CR (CCON.6) must be set by software to run the PCA. The PCA is shut off by clearing this bit. • Bit CF: The CF bit (CCON.7) is set when the PCA counter overflows and an interrupt will be generated if the ECF bit in the CMOD register is set. The CF bit can only be cleared by software. • Bits 0 through 4 are the flags for the modules (bit 0 for module 0, bit 1 for module 1, etc.) and are set by hardware when either a match or a capture occurs. These flags can only be cleared by software. 25 4113B–8051–03/05 Table 12. CCON Register CCON - PCA Counter Control Register (D8h) 7 6 5 4 3 2 1 0 CF CR - CCF4 CCF3 CCF2 CCF1 CCF0 Bit Number Bit Mnemonic Description PCA Counter Overflow flag 7 CF 6 CR Set by hardware when the counter rolls over. CF flags an interrupt if bit ECF in CMOD is set. CF may be set by either hardware or software but can only be cleared by software. PCA Counter Run control bit Must be cleared by software to turn the PCA counter off. Set by software to turn the PCA counter on. 5 - 4 CCF4 Reserved The value read from this bit is indeterminate. Do not set this bit. PCA Module 4 interrupt flag Must be cleared by software. Set by hardware when a match or capture occurs. PCA Module 3 interrupt flag 3 CCF3 Must be cleared by software. Set by hardware when a match or capture occurs. PCA Module 2 interrupt flag 2 CCF2 Must be cleared by software. Set by hardware when a match or capture occurs. PCA Module 1 interrupt flag 1 CCF1 Must be cleared by software. Set by hardware when a match or capture occurs. PCA Module 0 interrupt flag 0 CCF0 Must be cleared by software. Set by hardware when a match or capture occurs. Reset Value = 000X 0000b Not bit addressable The watchdog timer function is implemented in module 4 (see Figure 11). The PCA interrupt system is shown in Figure 9. 26 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Figure 9. PCA Interrupt System CF CR CCF4 CCF3 CCF2 CCF1 CCF0 CCON 0xD8 PCA Timer/Counter Module 0 Module 1 To Interrupt Priority Decoder Module 2 Module 3 Module 4 CMOD.0 ECF ECCFn CCAPMn.0 IE.6 EC IE.7 EA PCA Modules: each one of the five compare/capture modules has six possible functions. It can perform: • 16-bit Capture, positive-edge triggered • 16-bit Capture, negative-edge triggered • 16-bit Capture, both positive and negative-edge triggered • 16-bit Software Timer • 16-bit High-speed Output • 8-bit Pulse Width Modulator In addition, module 4 can be used as a Watchdog Timer. Each module in the PCA has a special function register associated with it. These registers are: CCAPM0 for module 0, CCAPM1 for module 1, etc. (see Table 13). The registers contain the bits that control the mode that each module will operate in. • The ECCF bit (CCAPMn.0 where n = 0, 1, 2, 3, or 4 depending on the module) enables the CCF flag in the CCON SFR to generate an interrupt when a match or compare occurs in the associated module. • PWM (CCAPMn.1) enables the pulse width modulation mode. • The TOG bit (CCAPMn.2) when set causes the CEX output associated with the module to toggle when there is a match between the PCA counter and the module's capture/compare register. • The match bit MAT (CCAPMn.3) when set will cause the CCFn bit in the CCON register to be set when there is a match between the PCA counter and the module's capture/compare register. • The next two bits CAPN (CCAPMn.4) and CAPP (CCAPMn.5) determine the edge that a capture input will be active on. The CAPN bit enables the negative edge, and the CAPP bit enables the positive edge. If both bits are set both edges will be enabled and a capture will occur for either transition. • The last bit in the register ECOM (CCAPMn.6) when set enables the comparator function. 27 4113B–8051–03/05 Table 13 shows the CCAPMn settings for the various PCA functions. Table 13. CCAPMn Registers (n = 0-4) CCAPM0 - PCA Module 0 Compare/Capture Control Register (0DAh) CCAPM1 - PCA Module 1 Compare/Capture Control Register (0DBh) CCAPM2 - PCA Module 2 Compare/Capture Control Register (0DCh) CCAPM3 - PCA Module 3 Compare/Capture Control Register (0DDh) CCAPM4 - PCA Module 4 Compare/Capture Control Register (0DEh) 7 6 5 4 3 2 1 0 - ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn Bit Number Bit Mnemonic Description 7 - 6 ECOMn Reserved The value read from this bit is indeterminate. Do not set this bit. Enable Comparator Cleared to disable the comparator function. Set to enable the comparator function. Capture Positive 5 CAPPn 4 CAPNn Cleared to disable positive edge capture. Set to enable positive edge capture. Capture Negative Cleared to disable negative edge capture. Set to enable negative edge capture. Match 3 MATn 2 TOGn 1 PWMn When MATn = 1, a match of the PCA counter with this module's compare/capture register causes the CCFn bit in CCON to be set, flagging an interrupt. Toggle When TOGn = 1, a match of the PCA counter with this module's compare/capture register causes the CEXn pin to toggle. Pulse Width Modulation Mode Cleared to disable the CEXn pin to be used as a pulse width modulated output. Set to enable the CEXn pin to be used as a pulse width modulated output. Enable CCF interrupt 0 CCF0 Cleared to disable compare/capture flag CCFn in the CCON register to generate an interrupt. Set to enable compare/capture flag CCFn in the CCON register to generate an interrupt. Reset Value = X000 0000b Not bit addressable 28 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 14. PCA Module Modes (CCAPMn Registers) ECOMn CAPPn CAPNn MATn TOGn PWMm ECCFn Module Function 0 0 0 0 0 0 0 No Operation X 1 0 0 0 0 X 16-bit capture by a positive-edge trigger on CEXn X 0 1 0 0 0 X 16-bit capture by a negative trigger on CEXn X 1 1 0 0 0 X 16-bit capture by a transition on CEXn 1 0 0 1 0 0 X 16-bit Software Timer/Compare mode. 1 0 0 1 1 0 X 16-bit High-speed Output 1 0 0 0 0 1 0 8-bit PWM 1 0 0 1 X 0 X Watchdog Timer (module 4 only) There are two additional registers associated with each of the PCA modules. They are CCAPnH and CCAPnL and these are the registers that store the 16-bit count when a capture occurs or a compare should occur. When a module is used in the PWM mode these registers are used to control the duty cycle of the output (see Table 15 and Table 16). Table 15. CCAPnH Registers (n = 0-4) CCAP0H - PCA Module 0 Compare/Capture Control Register High (0FAh) CCAP1H - PCA Module 1 Compare/Capture Control Register High (0FBh) CCAP2H - PCA Module 2 Compare/Capture Control Register High (0FCh) CCAP3H - PCA Module 3 Compare/Capture Control Register High (0FDh) CCAP4H - PCA Module 4 Compare/Capture Control Register High (0FEh) 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description - PCA Module n Compare/Capture Control CCAPnH Value Reset Value = 0000 0000b Not bit addressable 29 4113B–8051–03/05 Table 16. CCAPnL Registers (n = 0-4) CCAP0L - PCA Module 0 Compare/Capture Control Register Low (0EAh) CCAP1L - PCA Module 1 Compare/Capture Control Register Low (0EBh) CCAP2L - PCA Module 2 Compare/Capture Control Register Low (0ECh) CCAP3L - PCA Module 3 Compare/Capture Control Register Low (0EDh) CCAP4L - PCA Module 4 Compare/Capture Control Register Low (0EEh) 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description - PCA Module n Compare/Capture Control CCAPnL Value Reset Value = 0000 0000b Not bit addressable Table 17. CH Register CH - PCA Counter Register High (0F9h) 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description - PCA counter CH Value Reset Value = 0000 0000b Not bit addressable Table 18. CL Register CL - PCA Counter Register Low (0E9h) 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description - PCA Counter CL Value Reset Value = 0000 0000b Not bit addressable 30 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 PCA Capture Mode To use one of the PCA modules in the capture mode either one or both of the CCAPM bits CAPN and CAPP for that module must be set. The external CEX input for the module (on port 1) is sampled for a transition. When a valid transition occurs the PCA hardware loads the value of the PCA counter registers (CH and CL) into the module's capture registers (CCAPnL and CCAPnH). If the CCFn bit for the module in the CCON SFR and the ECCFn bit in the CCAPMn SFR are set then an interrupt will be generated (see Figure 10). Figure 10. PCA Capture Mode CF CR CCF4 CCF3 CCF2 CCF1 CCF0 CCON 0xD8 PCA IT PCA Counter/Timer Cex.n CH CL CCAPnH CCAPnL Capture ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn CCAPMn, n= 0 to 4 0xDA to 0xDE 16-bit Software Timer/ Compare Mode The PCA modules can be used as software timers by setting both the ECOM and MAT bits in the modules CCAPMn register. The PCA timer will be compared to the module's capture registers and when a match occurs an interrupt will occur if the CCFn (CCON SFR) and the ECCFn (CCAPMn SFR) bits for the module are both set (see Figure 11). 31 4113B–8051–03/05 Figure 11. PCA Compare Mode and PCA Watchdog Timer CCON CF Write to CCAPnL CR CCF4 CCF3 CCF2 CCF1 CCF0 0xD8 Reset PCA IT Write to CCAPnH 1 CCAPnH 0 CCAPnL Enable Match 16 bit comparator CH RESET * CL PCA counter/timer ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn CIDL WDTE CPS1 CPS0 ECF CCAPMn, n = 0 to 4 0xDA to 0xDE CMOD 0xD9 Before enabling ECOM bit, CCAPnL and CCAPnH should be set with a non zero value, otherwise an unwanted match could happen. Writing to CCAPnH will set the ECOM bit. Once ECOM set, writing CCAPnL will clear ECOM so that an unwanted match doesn’t occur while modifying the compare value. Writing to CCAPnH will set ECOM. For this reason, user software should write CCAPnL first, and then CCAPnH. Of course, the ECOM bit can still be controlled by accessing to CCAPMn register. High-speed Output Mode In this mode, the CEX output (on port 1) associated with the PCA module will toggle each time a match occurs between the PCA counter and the module's capture registers. To activate this mode the TOG, MAT, and ECOM bits in the module's CCAPMn SFR must be set (see Figure 12). A prior write must be done to CCAPnL and CCAPnH before writing the ECOMn bit. 32 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Figure 12. PCA High-speed Output Mode CCON CF CR CCF4 CCF3 CCF2 CCF1 CCF0 0xD8 Write to CCA PnL Reset PCA IT Write to CCAPnH 1 CCAPnH 0 CCAPnL Enable 16 bit comparator CH Match CL CEXn PCA counter/timer ECO Mn CAPPn CAPNn MATn TOGn PWMn ECCFn CCAPMn, n = 0 to 4 0xDA to 0xDE Before enabling ECOM bit, CCAPnL and CCAPnH should be set with a non zero value, otherwise an unwanted match could occur. Once ECOM is set, writing CCAPnL will clear ECOM so that an unwanted match doesn’t occur while modifying the compare value. Writing to CCAPnH will set ECOM. For this reason, user software should write CCAPnL first, and then CCAPnH. Of course, the ECOM bit can still be controlled by accessing the CCAPMn register. Pulse Width Modulator Mode All of the PCA modules can be used as PWM outputs. Figure 13 shows the PWM function. The frequency of the output depends on the source for the PCA timer. All of the modules will have the same frequency of output because they all share the PCA timer. The duty cycle of each module is independently variable using the module's capture register CCAPLn. When the value of the PCA CL SFR is less than the value in the module's CCAPLn SFR the output will be low, when it is equal to or greater than the output will be high. When CL overflows from FF to 00, CCAPLn is reloaded with the value in CCAPHn. This allows updating the PWM without glitches. The PWM and ECOM bits in the module's CCAPMn register must be set to enable the PWM mode. 33 4113B–8051–03/05 Figure 13. PCA PWM Mode CCAPnH Overflow CCAPnL “0” CEXn Enable 8-Bit Comparator “1” CL PCA Counter/Timer ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn CCAPMn, n= 0 to 4 0xDA to 0xDE PCA Watchdog Timer An on-board watchdog timer is available with the PCA to improve the reliability of the system without increasing chip count. Watchdog timers are useful for systems that are susceptible to noise, power glitches, or electrostatic discharge. Module 4 is the only PCA module that can be programmed as a watchdog. However, this module can still be used for other modes if the watchdog is not needed. Figure 11 shows a diagram of how the watchdog works. The user pre-loads a 16-bit value in the compare registers. Just like the other compare modes, this 16-bit value is compared to the PCA timer value. If a match is allowed to occur, an internal reset will be generated. This will not cause the RST pin to be driven high. In order to hold off the reset, the user has three options: 1. Periodically change the compare value so it will never match the PCA timer. 2. Periodically change the PCA timer value so it will never match the compare values. 3. Disable the watchdog by clearing the WDTE bit before a match occurs and then re-enable it. The first two options are more reliable because the watchdog timer is never disabled as in option #3. If the program counter ever goes astray, a match will eventually occur and cause an internal reset. The second option is also not recommended if other PCA modules are being used. Remember, the PCA timer is the time base for all modules; changing the time base for other modules would not be a good idea. Thus, in most applications the first solution is the best option. This watchdog timer won’t generate a reset out on the reset pin. 34 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Serial I/O Port The serial I/O port in the T8xc51Rx2 is compatible with the serial I/O port in the 80C52. It provides both synchronous and asynchronous communication modes. It operates as a Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex modes (Modes 1, 2 and 3). Asynchronous transmission and reception can occur simultaneously and at different baud rates Serial I/O port includes the following enhancements: Framing Error Detection • Framing error detection • Automatic address recognition Framing bit error detection is provided for the three asynchronous modes (modes 1, 2 and 3). To enable the framing bit error detection feature, set SMOD0 bit in PCON register (see Figure 14). Figure 14. Framing Error Block diagram SM 0/FE SM 1 SM 2 RE N TB8 RB8 TI RI S CO N (9 8h ) Se t FE bit if stop bit is 0 (fram ing erro r) (SM OD0 = 1) SM 0 to UA RT m o de con tro l (SM OD0 = 0 ) SM OD1 1 SM OD0 - PO F GF1 GF0 PD IDL PCON (87 h) To UA RT fra min g e rro r co nt ro l When this feature is enabled, the receiver checks each incoming data frame for a valid stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous transmission by two CPUs. If a valid stop bit is not found, the Framing Error bit (FE) in SCON register (see Table 22) bit is set. Software may examine FE bit after each reception to check for data errors. Once set, only software or a reset can clear FE bit. Subsequently, received frames with valid stop bits cannot clear FE bit. When FE feature is enabled, RI rises on stop bit instead of the last data bit (see Figure 15 and Figure 16). Figure 15. UART Timings in Mode 1 RXD D0 Start bit D1 D2 D3 D4 Data byte D5 D6 D7 Stop bit RI SMOD0=X FE SMOD0=1 35 4113B–8051–03/05 Figure 16. UART Timings in Modes 2 and 3 RXD D0 D1 .Start Bit D2 D3 D4 D5 Data Byte D6 D7 D8 Ninth Stop Bit Bit RI SMOD0 = 0 RI SMOD0 = 1 FE SMOD0 = 1 Automatic Address Recognition The automatic address recognition feature is enabled when the multiprocessor communication feature is enabled (SM2 bit in SCON register is set). Implemented in hardware, automatic address recognition enhances the multiprocessor communication feature by allowing the serial port to examine the address of each incoming command frame. Only when the serial port recognizes its own address, the receiver sets RI bit in SCON register to generate an interrupt. This ensures that the CPU is not interrupted by command frames addressed to other devices. If desired, you may enable the automatic address recognition feature in mode 1. In this configuration, the stop bit takes the place of the ninth data bit. Bit RI is set only when the received command frame address matches the device’s address and is terminated by a valid stop bit. To support automatic address recognition, a device is identified by a given address and a broadcast address. Note: Given Address The multiprocessor communication and automatic address recognition features cannot be enabled in mode 0 (i.e. setting SM2 bit in SCON register in mode 0 has no effect). Each device has an individual address that is specified in SADDR register; the SADEN register is a mask byte that contains don’t care bits (defined by zeros) to form the device’s given address. The don’t care bits provide the flexibility to address one or more slaves at a time. The following example illustrates how a given address is formed. To address a device by its individual address, the SADEN mask byte must be 1111 1111b. For example: SADDR0101 0110b SADEN1111 1100b Given0101 01XXb The following is an example of how to use given addresses to address different slaves: Slave A:SADDR1111 0001b SADEN1111 1010b Given1111 0X0Xb Slave B:SADDR1111 0011b SADEN1111 1001b Given1111 0XX1b Slave C:SADDR1111 0010b SADEN1111 1101b Given1111 00X1b 36 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 The SADEN byte is selected so that each slave may be addressed separately. For slave A, bit 0 (the LSB) is a don’t-care bit; for slaves B and C, bit 0 is a 1. To communicate with slave A only, the master must send an address where bit 0 is clear (e.g. 1111 0000b). For slave A, bit 1 is a 1; for slaves B and C, bit 1 is a don’t care bit. To communicate with slaves B and C, but not slave A, the master must send an address with bits 0 and 1 both set (e.g. 1111 0011b). To communicate with slaves A, B and C, the master must send an address with bit 0 set, bit 1 clear, and bit 2 clear (e.g. 1111 0001b). Broadcast Address A broadcast address is formed from the logical OR of the SADDR and SADEN registers with zeros defined as don’t-care bits, e.g.: SADDR 0101 0110b SADEN 1111 1100b Broadcast = SADDR OR SADEN1111 111Xb The use of don’t-care bits provides flexibility in defining the broadcast address, however in most applications, a broadcast address is FFh. The following is an example of using broadcast addresses: Slave A:SADDR1111 0001b SADEN1111 1010b Broadcast1111 1X11b, Slave B:SADDR1111 0011b SADEN1111 1001b Broadcast1111 1X11B, Slave C:SADDR = 1111 0010b SADEN1111 1101b Broadcast1111 1111b For slaves A and B, bit 2 is a don’t care bit; for slave C, bit 2 is set. To communicate with all of the slaves, the master must send an address FFh. To communicate with slaves A and B, but not slave C, the master can send and address FBh. Reset Addresses On reset, the SADDR and SADEN registers are initialized to 00h, i.e. the given and broadcast addresses are XXXX XXXXb (all don’t-care bits). This ensures that the serial port will reply to any address, and so, that it is backwards compatible with the 80C51 microcontrollers that do not support automatic address recognition. Table 19. SADEN Register SADEN - Slave Address Mask Register (B9h) 7 6 5 4 3 2 1 0 Reset Value = 0000 0000b Not bit addressable 37 4113B–8051–03/05 Table 20. SADDR Register SADDR - Slave Address Register (A9h) 7 6 5 4 3 2 1 0 Reset Value = 0000 0000b Not bit addressable Baud Rate Selection for UART for Mode 1 and 3 The Baud Rate Generator for transmit and receive clocks can be selected separately via the T2CON and BDRCON registers. Figure 17. Baud Rate selection TIMER1 0 TIMER2 TI MER_BRG_RX 0 1 / 16 Rx Clock 1 RCLK RBCK INT_BRG TIMER1 0 TI MER2 TIMER_BRG_TX 0 1 / 16 1 Tx Clock TCLK TBCK INT_BRG Table 21. Baud Rate Selection Table UART 38 TCLK RCLK TBCK RBCK Clock Source Clock Source (T2CON) (T2CON) (BDRCON) (BDRCON) UART Tx UART Rx 0 0 0 0 Timer 1 Timer 1 1 0 0 0 Timer 2 Timer 1 0 1 0 0 Timer 1 Timer 2 1 1 0 0 Timer 2 Timer 2 X 0 1 0 INT_BRG Timer 1 X 1 1 0 INT_BRG Timer 2 0 X 0 1 Timer 1 INT_BRG 1 X 0 1 Timer 2 INT_BRG X X 1 1 INT_BRG INT_BRG AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Internal Baud Rate Generator (BRG) When the internal Baud Rate Generator is used, the Baud Rates are determined by the BRG overflow depending on the BRL reload value, the value of SPD bit (Speed Mode) in BDRCON register and the value of the SMOD1 bit in PCON register. Figure 18. Internal Baud Rate auto reload counter Peripheral clock /6 0 overflow /2 BRG 1 SPD 0 INT_BRG 1 BRL BRR • The baud rate for UART is token by formula: 2 SMOD × F CLKPERIPH BaudRate = ---------------------------------------------------------------------------------------------------------2 × 2 × 6 〈 1 – SPD〉 × 16 × [ 256 – ( BRL ) ] 2 SMOD 1 × F CLKPERIPH ( BRL ) = 256 – ----------------------------------------------------------------------------------------2 × 2 × 6 ( 1 – SPD ) × 16 × BaudRate 39 4113B–8051–03/05 Table 22. SCON Register SCON - Serial Control Register (98h) 7 6 5 4 3 2 1 0 FE/SM0 SM1 SM2 REN TB8 RB8 TI RI Bit Bit Number Mnemonic 7 FE SM0 Description Framing Error bit (SMOD0 = 1) Clear to reset the error state, not cleared by a valid stop bit. Set by hardware when an invalid stop bit is detected. SMOD0 must be set to enable access to the FE bit Serial port Mode bit 0 Refer to SM1 for serial port mode selection. SMOD0 must be cleared to enable access to the SM0 bit Serial port Mode bit 1 6 SM1 SM1 0 1 0 1 Mode 0 1 2 3 Description Shift Register 8-bit UART 9-bit UART 9-bit UART Baud Rate fCPU PERIPH/6 Variable fCPU PERIPH /32 or /16 Variable Serial port Mode 2 bit/Multiprocessor Communication Enable bit 5 SM2 4 REN 3 TB8 Clear to disable multiprocessor communication feature. Set to enable multiprocessor communication feature in mode 2 and 3, and eventually mode 1. This bit should be cleared in mode 0. Reception Enable bit Clear to disable serial reception. Set to enable serial reception. Transmitter Bit 8/Ninth bit to transmit in modes 2 and 3 2 RB8 o transmit a logic 0 in the 9th bit. Set to transmit a logic 1 in the 9th bit. Receiver Bit 8/Ninth bit received in modes 2 and 3 Cleared by hardware if 9th bit received is a logic 0. Set by hardware if 9th bit received is a logic 1. In mode 1, if SM2=0, RB8 is the received stop bit. In mode 0 RB8 is not used. 1 0 TI Transmit Interrupt flag Clear to acknowledge interrupt. Set by hardware at the end of the 8th bit time in mode 0 or at the beginning of the stop bit in the other modes. RI Receive Interrupt flag Clear to acknowledge interrupt. Set by hardware at the end of the 8th bit time in mode 0, see Figure 15. and Figure 16. in the other modes. Reset Value = 0000 0000b Bit addressable 40 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 23. Example of Computed Value when X2 = 1, SMOD1 = 1, SPD = 1 Baud Rates FOSC=16.384 MHz FOSC=24 MHz BRL Error (%) BRL Error (%) 115200 247 1.23 243 0.16 57600 238 1.23 230 0.16 38400 229 1.23 217 0.16 28800 220 1.23 204 0.16 19200 203 0.63 178 0.16 9600 149 0.31 100 0.16 4800 43 1.23 - - Table 24. Example of Computed Value when X2 = 0, SMOD1 = 0, SPD = 0 Baud Rates FOSC=16.384 MHz FOSC=24 MHz BRL Error (%) BRL Error (%) 4800 247 1.23 243 0.16 2400 238 1.23 230 0.16 1200 220 1.23 202 3.55 600 185 0.16 152 0.16 The baud rate generator can be used for mode 1 or 3 (see Figure 17.), but also for mode 0 for UART, thanks to the bit SRC located in BDRCON register (Table 31.) 41 4113B–8051–03/05 UART Registers Table 25. SADEN Register SADEN - Slave Address Mask Register for UART (B9h) 7 6 5 4 3 2 1 0 3 2 1 0 3 2 1 0 Reset Value = 0000 0000b Table 26. SADDR Register SADDR - Slave Address Register for UART (A9h) 7 6 5 4 Reset Value = 0000 0000b Table 27. SBUF Register SBUF - Serial Buffer Register for UART (99h) 7 6 5 4 Reset Value = XXXX XXXXb Table 28. BRL Register BRL - Baud Rate Reload Register for the internal baud rate generator, UART (9Ah) 7 6 5 4 3 2 1 0 Reset Value = 0000 0000b 42 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 29. T2CON Register T2CON - Timer 2 Control Register (C8h) 7 6 5 4 3 2 1 0 TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2# CP/RL2# Bit Bit Number Mnemonic 7 TF2 Description Timer 2 overflow Flag Must be cleared by software. Set by hardware on Timer 2 overflow, if RCLK=0 and TCLK=0. 6 EXF2 Timer 2 External Flag Set when a capture or a reload is caused by a negative transition on T2EX pin if EXEN2 = 1. When set, causes the CPU to vector to Timer 2 interrupt routine when Timer 2 interrupt is enabled. Must be cleared by software. EXF2 doesn’t cause an interrupt in Up/down counter mode (DCEN=1) 5 RCLK Receive Clock bit for UART Cleared to use timer 1 overflow as receive clock for serial port in mode 1 or 3. Set to use Timer 2 overflow as receive clock for serial port in mode 1 or 3. 4 TCLK Transmit Clock bit for UART Cleared to use timer 1 overflow as transmit clock for serial port in mode 1 or 3. Set to use Timer 2 overflow as transmit clock for serial port in mode 1 or 3. 3 EXEN2 2 TR2 1 0 Timer 2 External Enable bit Cleared to ignore events on T2EX pin for Timer 2 operation. Set to cause a capture or reload when a negative transition on T2EX pin is detected, if Timer 2 is not used to clock the serial port. Timer 2 Run control bit Cleared to turn off Timer 2. Set to turn on Timer 2. C/T2# Timer/Counter 2 select bit Cleared for timer operation (input from internal clock system: FCLK PERIPH). Set for counter operation (input from T2 input pin, falling edge trigger). Must be 0 for clock out mode. CP/RL2# Timer 2 Capture/Reload bit If RCLK = 1 or TCLK = 1, CP/RL2# is ignored and timer is forced to auto-reload on Timer 2 overflow. Cleared to auto-reload on Timer 2 overflows or negative transitions on T2EX pin if EXEN2 = 1. Set to capture on negative transitions on T2EX pin if EXEN2 = 1. Reset Value = 0000 0000b Bit addressable 43 4113B–8051–03/05 Table 30. PCON Register PCON - Power Control Register (87h) 7 6 5 4 3 2 1 0 SMOD1 SMOD0 - POF GF1 GF0 PD IDL Bit Bit Number Mnemonic 7 SMOD1 6 SMOD0 5 - 4 POF Power-off Flag Cleared to recognize next reset type. Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by software. 3 GF1 General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. 2 GF0 General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. 1 PD Power-down mode bit Cleared by hardware when reset occurs. Set to enter power-down mode. 0 IDL Idle mode bit Cleared by hardware when interrupt or reset occurs. Set to enter idle mode. Description Serial Port Mode bit 1 for UART Set to select double baud rate in mode 1, 2 or 3. Serial Port Mode bit 0 for UART Cleared to select SM0 bit in SCON register. Set to select FE bit in SCON register. Reserved The value read from this bit is indeterminate. Do not set this bit. Reset Value = 00X1 0000b Not bit addressable Power-off flag reset value will be 1 only after a power on (cold reset). A warm reset doesn’t affect the value of this bit. 44 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 31. BDRCON Register BDRCON - Baud Rate Control Register (9Bh) 7 6 5 4 3 2 1 0 - - - BRR TBCK RBCK SPD SRC Bit Number Bit Mnemonic 7 - Reserved The value read from this bit is indeterminate. Do not set this bit 6 - Reserved The value read from this bit is indeterminate. Do not set this bit 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 BRR Baud Rate Run Control bit Cleared to stop the internal Baud Rate Generator. Set to start the internal Baud Rate Generator. 3 TBCK Transmission Baud rate Generator Selection bit for UART Cleared to select Timer 1 or Timer 2 for the Baud Rate Generator. Set to select internal Baud Rate Generator. 2 RBCK Reception Baud Rate Generator Selection bit for UART Cleared to select Timer 1 or Timer 2 for the Baud Rate Generator. Set to select internal Baud Rate Generator. 1 SPD Description Baud Rate Speed Control bit for UART Cleared to select the SLOW Baud Rate Generator. Set to select the FAST Baud Rate Generator. Baud Rate Source select bit in Mode 0 for UART 0 SRC Cleared to select FOSC/12 as the Baud Rate Generator (FCLK PERIPH/6 in X2 mode). Set to select the internal Baud Rate Generator for UARTs in mode 0. Reset Value = XXX0 0000b Not bit addressable 45 4113B–8051–03/05 Interrupt System The T8xc51Rx2 have a total of 8 interrupt vectors: two external interrupts (INT0 and INT1), three timer interrupts (timers 0, 1 and 2), the serial port interrupt, Keyboard interrupt and the PCA global interrupt. These interrupts are shown in Figure 19. Figure 19. Interrupt Control System High Priority Interrupt IPH, IPL 3 INT0 IE0 0 3 TF0 0 3 INT1 IE1 0 3 Interrupt Polling Sequence, Decreasing from High to Low Priority TF1 0 3 PCA IT 0 RI TI 3 TF2 EXF2 3 0 0 3 KBD IT 0 Individual Enable Global Disable Low Priority Interrupt Each of the interrupt sources can be individually enabled or disabled by setting or clearing a bit in the Interrupt Enable register (Table 36 and Table 34). This register also contains a global disable bit, which must be cleared to disable all interrupts at once. Each interrupt source also can be individually programmed to one out of four priority levels by setting or clearing a bit in the Interrupt Priority register (Table 37) and in the Interrupt Priority High register (Table 35 and Table 36) shows the bit values and priority levels associated with each combination. 46 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Registers The PCA interrupt vector is located at address 0033H, the Keyboard interrupt vector is located at address 004BH. All other vectors addresses are the same as standard C52 devices. Table 32. Priority Level Bit Values IPH.x IPL.x Interrupt Level Priority 0 0 0 (Lowest) 0 1 1 1 0 2 1 1 3 (Highest) A low-priority interrupt can be interrupted by a high priority interrupt, but not by another low-priority interrupt. A high-priority interrupt can’t be interrupted by any other interrupt source. If two interrupt requests of different priority levels are received simultaneously, the request of higher priority level is serviced. If interrupt requests of the same priority level are received simultaneously, an internal polling sequence determines which request is serviced. Thus within each priority level there is a second priority structure determined by the polling sequence. 47 4113B–8051–03/05 Table 33. IEO Register IE0 - Interrupt Enable Register (A8h) 7 6 5 4 3 2 1 0 EA EC ET2 ES ET1 EX1 ET0 EX0 Bit Number Bit Mnemonic Description Enable All interrupt bit Cleared to disable all interrupts. Set to enable all interrupts. 7 EA 6 EC 5 ET2 Timer 2 overflow interrupt enable bit Cleared to disable Timer 2 overflow interrupt. Set to enable Timer 2 overflow interrupt. 4 ES Serial port enable bit Cleared to disable serial port interrupt. Set to enable serial port interrupt. 3 ET1 Timer 1 overflow interrupt enable bit Cleared to disable timer 1 overflow interrupt. Set to enable timer 1 overflow interrupt. 2 EX1 External interrupt 1 enable bit Cleared to disable external interrupt 1. Set to enable external interrupt 1. 1 ET0 Timer 0 overflow interrupt enable bit Cleared to disable timer 0 overflow interrupt. Set to enable timer 0 overflow interrupt. 0 EX0 External interrupt 0 enable bit Cleared to disable external interrupt 0. Set to enable external interrupt 0. PCA interrupt enable bit Cleared to disable. Set to enable. Reset Value = 0000 0000b Bit addressable 48 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 34. IPL0 Register IPL0 - Interrupt Priority Register (B8h) 7 6 5 4 3 2 1 0 - PPCL PT2L PSL PT1L PX1L PT0L PX0L Bit Number Bit Mnemonic Description Reserved The value read from this bit is indeterminate. Do not set this bit. 7 - 6 PPCL PCA interrupt priority bit Refer to PPCH for priority level. 5 PT2L Timer 2 overflow interrupt priority bit Refer to PT2H for priority level. 4 PSL Serial port priority bit Refer to PSH for priority level. 3 PT1L Timer 1 overflow interrupt priority bit Refer to PT1H for priority level. 2 PX1L External interrupt 1 priority bit Refer to PX1H for priority level. 1 PT0L Timer 0 overflow interrupt priority bit Refer to PT0H for priority level. 0 PX0L External interrupt 0 priority bit Refer to PX0H for priority level. Reset Value = X000 0000b Bit addressable 49 4113B–8051–03/05 Table 35. IPH0 Register IPH0 - Interrupt Priority High Register (B7h) 7 6 5 4 3 2 1 0 - PPCH PT2H PSH PT1H PX1H PT0H PX0H Bit Number 7 6 5 4 3 2 1 0 Bit Mnemonic Description - Reserved The value read from this bit is indeterminate. Do not set this bit. PPCH PCA interrupt priority high bit. PPCH PPCL Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PT2H Timer 2 overflow interrupt priority high bit PT2H PT2L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PSH Serial port priority high bit PSH PSL Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PT1H Timer 1 overflow interrupt priority high bit PT1H PT1L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PX1H External interrupt 1 priority high bit PX1H PX1L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PT0H Timer 0 overflow interrupt priority high bit PT0H PT0L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PX0H External interrupt 0 priority high bit PX0H PX0L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest Reset Value = X000 0000b Not bit addressable 50 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 36. IE1 Register IE1 - Interrupt Enable Register (B1h) 7 6 5 4 3 2 1 0 - - - - - - - KBD Bit Number Bit Mnemonic Description 7 - Reserved 6 - Reserved 5 - Reserved 4 - Reserved 3 - Reserved 2 - Reserved 1 - Reserved 0 KBD Keyboard interrupt Enable bit Cleared to disable keyboard interrupt. Set to enable keyboard interrupt. Reset Value = XXXX XXX0b Bit addressable 51 4113B–8051–03/05 Table 37. IPL1 Register IPL1 - Interrupt Priority Register (B2h) 7 6 5 4 3 2 1 0 - - - - - - - KBDL Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 - Reserved The value read from this bit is indeterminate. Do not set this bit. 1 - Reserved The value read from this bit is indeterminate. Do not set this bit. 0 KBDL Keyboard Interrupt Priority bit Refer to KBDH for priority level. Reset Value = XXXX XXX0b Bit addressable 52 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 38. IPH1 Register IPH1 - Interrupt Priority High Register (B3h) 7 6 5 4 3 2 1 0 - - - - - - - KBDH Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 - Reserved The value read from this bit is indeterminate. Do not set this bit. 1 - Reserved The value read from this bit is indeterminate. Do not set this bit. 0 KBDH Keyboard interrupt Priority High bit KB DH KBDL Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest Reset Value = XXXX XXX0b Not bit addressable 53 4113B–8051–03/05 Interrupt Sources and Vector Addresses 54 Table 39. Interrupt Sources and Vector Addresses Interrupt Request Vector Number Polling Priority Interrupt Source Address 0 0 Reset 1 1 INT0 IE0 0003h 2 2 Timer 0 TF0 000Bh 3 3 INT1 IE1 0013h 4 4 Timer 1 IF1 001Bh 5 6 UART RI+TI 0023h 6 7 Timer 2 TF2+EXF2 002Bh 7 5 PCA CF + CCFn (n = 0-4) 0033h 8 8 Keyboard KBDIT 003Bh 0000h AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Keyboard Interface The T8xc51Rx2 implement a keyboard interface allowing the connection of a 8 x n matrix keyboard. It is based on 8 inputs with programmable interrupt capability on both high or low level. These inputs are available as alternate function of P1 and allow to exit from idle and power-down modes. The keyboard interfaces with the C51 core through 3 special function registers: KBLS, the Keyboard Level Selection register (Table 42), KBE, The Keyboard Interrupt Enable register (Table 41), and KBF, the Keyboard Flag register (Table 40). Interrupt The keyboard inputs are considered as 8 independent interrupt sources sharing the same interrupt vector. An interrupt enable bit (KBD in IE1) allows global enable or disable of the keyboard interrupt (see Figure 20). As detailed in Figure 21 each keyboard input has the capability to detect a programmable level according to KBLS.x bit value. Level detection is then reported in interrupt flags KBF.x that can be masked by software using KBE.x bits. This structure allow keyboard arrangement from 1 x n to 8 x n matrix and allows usage of P1 inputs for other purpose. Figure 20. Keyboard Interface Block Diagram VCC 0 P1:x KBF.x 1 Internal Pull-up KBE.x KBLS.x Figure 21. Keyboard Input Circuitry P1.0 Input Circuitry P1.1 Input Circuitry P1.2 Input Circuitry P1.3 Input Circuitry P1.4 Input Circuitry P1.5 Input Circuitry P1.6 Input Circuitry P1.7 Input Circuitry KBDIT Power Reduction Mode KBD IE1 Keyboard Interface Interrupt Request P1 inputs allow exit from idle and power-down modes as detailed in Section “Powerdown Mode”, page 59. 55 4113B–8051–03/05 Registers Table 40. KBF Register KBF - Keyboard Flag Register (9Eh) 7 6 5 4 3 2 1 0 KBF7 KBF6 KBF5 KBF4 KBF3 KBF2 KBF1 KBF0 Bit Number 7 6 5 4 3 2 1 0 Bit Mnemonic Description KBF7 Keyboard line 7 flag Set by hardware when the Port line 7 detects a programmed level. It generates a Keyboard interrupt request if the KBKBIE.7 bit in KBIE register is set. Must be cleared by software. KBF6 Keyboard line 6 flag Set by hardware when the Port line 6 detects a programmed level. It generates a Keyboard interrupt request if the KBIE.6 bit in KBIE register is set. Must be cleared by software. KBF5 Keyboard line 5 flag Set by hardware when the Port line 5 detects a programmed level. It generates a Keyboard interrupt request if the KBIE.5 bit in KBIE register is set. Must be cleared by software. KBF4 Keyboard line 4 flag Set by hardware when the Port line 4 detects a programmed level. It generates a Keyboard interrupt request if the KBIE.4 bit in KBIE register is set. Must be cleared by software. KBF3 Keyboard line 3 flag Set by hardware when the Port line 3 detects a programmed level. It generates a Keyboard interrupt request if the KBIE.3 bit in KBIE register is set. Must be cleared by software. KBF2 Keyboard line 2 flag Set by hardware when the Port line 2 detects a programmed level. It generates a Keyboard interrupt request if the KBIE.2 bit in KBIE register is set. Must be cleared by software. KBF1 Keyboard line 1 flag Set by hardware when the Port line 1 detects a programmed level. It generates a Keyboard interrupt request if the KBIE.1 bit in KBIE register is set. Must be cleared by software. KBF0 Keyboard line 0 flag Set by hardware when the Port line 0 detects a programmed level. It generates a Keyboard interrupt request if the KBIE.0 bit in KBIE register is set. Must be cleared by software. Reset Value = 0000 0000b 56 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 41. KBE Register KBE - Keyboard Input Enable Register (9Dh) 7 6 5 4 3 2 1 0 KBE7 KBE6 KBE5 KBE4 KBE3 KBE2 KBE1 KBE0 Bit Number Bit Mnemonic Description 7 KBE7 Keyboard line 7 enable bit Cleared to enable standard I/O pin. Set to enable KBF.7 bit in KBF register to generate an interrupt request. 6 KBE6 Keyboard line 6 enable bit Cleared to enable standard I/O pin. Set to enable KBF.6 bit in KBF register to generate an interrupt request. 5 KBE5 Keyboard line 5 enable bit Cleared to enable standard I/O pin. Set to enable KBF.5 bit in KBF register to generate an interrupt request. 4 KBE4 Keyboard line 4 enable bit Cleared to enable standard I/O pin. Set to enable KBF.4 bit in KBF register to generate an interrupt request. 3 KBE3 Keyboard line 3 enable bit Cleared to enable standard I/O pin. Set to enable KBF.3 bit in KBF register to generate an interrupt request. 2 KBE2 Keyboard line 2 enable bit Cleared to enable standard I/O pin. Set to enable KBF.2 bit in KBF register to generate an interrupt request. 1 KBE1 Keyboard line 1 enable bit Cleared to enable standard I/O pin. Set to enable KBF.1 bit in KBF register to generate an interrupt request. 0 KBE0 Keyboard line 0 enable bit Cleared to enable standard I/O pin. Set to enable KBF.0 bit in KBF register to generate an interrupt request. Reset Value = 0000 0000b 57 4113B–8051–03/05 Table 42. KBLS Register KBLS - Keyboard Level Selector Register (9Ch) 7 6 5 4 3 2 1 0 KBLS7 KBLS6 KBLS5 KBLS4 KBLS3 KBLS2 KBLS1 KBLS0 Bit Number Bit Mnemonic Description 7 KBLS7 Keyboard line 7 level selection bit Cleared to enable a low level detection on Port line 7. Set to enable a high level detection on Port line 7. 6 KBLS6 Keyboard line 6 level selection bit Cleared to enable a low level detection on Port line 6. Set to enable a high level detection on Port line 6. 5 KBLS5 Keyboard line 5 level selection bit Cleared to enable a low level detection on Port line 5. Set to enable a high level detection on Port line 5. 4 KBLS4 Keyboard line 4 level selection bit Cleared to enable a low level detection on Port line 4. Set to enable a high level detection on Port line 4. 3 KBLS3 Keyboard line 3 level selection bit Cleared to enable a low level detection on Port line 3. Set to enable a high level detection on Port line 3. 2 KBLS2 Keyboard line 2 level selection bit Cleared to enable a low level detection on Port line 2. Set to enable a high level detection on Port line 2. 1 KBLS1 Keyboard line 1 level selection bit Cleared to enable a low level detection on Port line 1. Set to enable a high level detection on Port line 1. 0 KBLS0 Keyboard line 0 level selection bit Cleared to enable a low level detection on Port line 0. Set to enable a high level detection on Port line 0. Reset Value = 0000 0000b 58 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Power Management Idle Mode An instruction that sets PCON.0 indicates that it is the last instruction to be executed before going into Idle mode. In Idle mode, the internal clock signal is gated off to the CPU, but not to the interrupt, Timer, and Serial Port functions. The CPU status is preserved in its entirety: the Stack Pointer, Program Counter, Program Status Word, Accumulator and all other registers maintain their data during idle. The port pins hold the logical states they had at the time Idle was activated. ALE and PSEN hold at logic high level. There are two ways to terminate the Idle mode. Activation of any enabled interrupt will cause PCON.0 to be cleared by hardware, terminating the Idle mode. The interrupt will be serviced, and following RETI the next instruction to be executed will be the one following the instruction that put the device into idle. The flag bits GF0 and GF1 can be used to give an indication if an interrupt occurred during normal operation or during idle. For example, an instruction that activates idle can also set one or both flag bits. When idle is terminated by an interrupt, the interrupt service routine can examine the flag bits. The other way of terminating the Idle mode is with a hardware reset. Since the clock oscillator is still running, the hardware reset needs to be held active for only two machine cycles (24 oscillator periods) to complete the reset. Power-down Mode To save maximum power, a power-down mode can be invoked by software (refer to Table 30, PCON register). In power-down mode, the oscillator is stopped and the instruction that invoked powerdown mode is the last instruction executed. The internal RAM and SFRs retain their value until the power-down mode is terminated. VCC can be lowered to save further power. Either a hardware reset or an external interrupt can cause an exit from powerdown. To properly terminate power-down, the reset or external interrupt should not be executed before VCC is restored to its normal operating level and must be held active long enough for the oscillator to restart and stabilize. Only external interrupts INT0, INT1 and Keyboard Interrupts are useful to exit from power-down. Thus, the interrupt must be enabled and configured as level - or edge sensitive interrupt input. When Keyboard Interrupt occurs after a power-down mode, 1024 clocks are necessary to exit to power-down mode and enter in operating mode. Holding the pin low restarts the oscillator but bringing the pin high completes the exit as detailed in Figure 22. When both interrupts are enabled, the oscillator restarts as soon as one of the two inputs is held low and power-down exit will be completed when the first input is released. In this case, the higher priority interrupt service routine is executed. Once the interrupt is serviced, the next instruction to be executed after RETI will be the one following the instruction that put T8xc51Rx2 into power-down mode. 59 4113B–8051–03/05 Figure 22. Power-down Exit Waveform INT0 INT1 XTAL Active Phase Power-down Phase OscillatoR Restart Phase Active Phase Exit from power-down by reset redefines all the SFRs, exit from power-down by external interrupt does no affect the SFRs. Exit from power-down by either reset or external interrupt does not affect the internal RAM content. Note: If idle mode is activated with power-down mode (IDL and PD bits set), the exit sequence is unchanged, when execution is vectored to interrupt, PD and IDL bits are cleared and idle mode is not entered. Table 43 shows the state of ports during idle and power-down modes. Table 43. State of Ports Mode ALE PSEN PORT0 (1) PORT1 PORT2 PORT3 Idle Internal 1 1 Port Data Port Data Port Data Port Data Idle External 1 1 Floating Port Data Address Port Data Port Data Port Data Port Data Port Data Port Data Port Data Power-down Internal 0 0 Power-down External 0 0 Note: 60 Program Memory Port Dat (1) Floating 1. Port 0 can force a 0 level. A "one" will leave port floating. AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Hardware Watchdog Timer The WDT is intended as a recovery method in situations where the CPU may be subjected to software upset. The WDT consists of a 14-bit counter and the WatchDog Timer Reset (WDTRST) SFR. The WDT is by default disabled from exiting reset. To enable the WDT, user must write 01EH and 0E1H in sequence to the WDTRST, SFR location 0A6H. When WDT is enabled, it will increment every machine cycle while the oscillator is running and there is no way to disable the WDT except through reset (either hardware reset or WDT overflow reset). When WDT overflows, it will drive an output RESET HIGH pulse at the RST-pin. Using the WDT To enable the WDT, user must write 01EH and 0E1H in sequence to the WDTRST, SFR location 0A6H. When WDT is enabled, the user needs to service it by writing to 01EH and 0E1H to WDTRST to avoid WDT overflow. The 14-bit counter overflows when it reaches 16383 (3FFFH) and this will reset the device. When WDT is enabled, it will increment every machine cycle while the oscillator is running. Therefore, the user must reset the WDT at least every 16383 machine cycles. To reset the WDT the user must write 01EH and 0E1H to WDTRST. WDTRST is a write only register. The WDT counter cannot be read or written. When WDT overflows, it will generate an output RESET pulse at the RST-pin. The RESET pulse duration is 96 x TCLK PERIPH, where TCLK PERIPH= 1/FCLK PERIPH. To make the best use of the WDT, it should be serviced in those sections of code that will periodically be executed within the time required to prevent a WDT reset. To have a more powerful WDT, a 27 counter has been added to extend the Time-out capability, ranking from 16 ms to 2s @ Fosc = 12 MHz. To manage this feature, refer to WDTPRG register description, Table 44. Table 44. WDTRST Register WDTRST - Watchdog Reset Register (0A6h) 7 6 5 4 3 2 1 0 - - - - - - - - Reset Value = XXXX XXXXb Write only, this SFR is used to reset/enable the WDT by writing 01EH then 0E1H in sequence. 61 4113B–8051–03/05 Table 45. WDTPRG Register WDTPRG - Watchdog Timer Out Register (0A7h) 7 6 5 4 3 2 1 0 - - - - - S2 S1 S0 Bit Number Bit Mnemonic Description 7 - 6 - 5 - 4 - 3 - 2 S2 WDT Time-out select bit 2 1 S1 WDT Time-out select bit 1 0 S0 WDT Time-out select bit 0 Reserved The value read from this bit is undetermined. Do not try to set this bit. S2 0 0 0 0 1 1 1 1 S1 0 0 1 1 0 0 1 1 S0 0 1 0 1 0 1 0 1 Selected Time-out (214 - 1) machine cycles, 16. 3 ms @ Fosc =12 MHz (215 - 1) machine cycles, 32.7 ms @ Fosc=12 MHz (216 - 1) machine cycles, 65. 5 ms @ Fosc=12 MHz (217 - 1) machine cycles, 131 ms @ Fosc=12 MHz (218 - 1) machine cycles, 262 ms @ Fosc=12 MHz (219 - 1) machine cycles, 542 ms @ Fosc=12 MHz (220 - 1) machine cycles, 1.05 s @ Fosc=12 MHz (221 - 1) machine cycles, 2.09 s @ Fosc=12 MHz Reset Value = XXXX X000 WDT During Power-down In Power-down mode the oscillator stops, which means the WDT also stops. While in Power-down mode the user does not need to service the WDT. There are 2 methods of and Idle exiting Power-down mode: by a hardware reset or via a level activated external interrupt which is enabled prior to entering Power-down mode. When Power-down is exited with hardware reset, servicing the WDT should occur as normal, whenever the T8xc51Rx2 is reset. Exiting Power-down with an interrupt is significantly different. The interrupt is held low long enough for the oscillator to stabilize. When the interrupt is brought high, the interrupt is serviced. To prevent the WDT from resetting the device while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high. It is suggested that the WDT be reset during the interrupt service routine. To ensure that the WDT does not overflow within a few states of exiting of power-down, it is better to reset the WDT just before entering power-down. In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting the T8xc51Rx2 while in Idle mode, the user should always set up a timer that will periodically exit Idle, service the WDT, and re-enter Idle mode. 62 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 ROM ROM Structure Hardware Config Byte The T89C51RB2/RC2 ROM memory is divided in two different arrays: • The code array:16/32K bytes. • The config byte: 1 byte. The config byte sets the starting microcontroller options and the security levels. The starting options are X2 mode, and XRAM. 7 6 5 4 3 2 1 0 X2 - - - XRAM - LB1 LB0 Bit Bit Number Mnemonic 7 X2 Description X2 Mode Cleared to force X2 mode (6 clocks per instruction) Set to force X1 mode, Standard Mode. 6 - Reserved 5 - Reserved 4 - Reserved 3 XRAM 2 - 1-0 LB0-1 XRAM config bit ROM Lock System Set this bit to enable XRAM. Clear this bit to disable XRAM. Reserved User Program ROM Lock Bits see Table 46. The program Lock system, when programmed, protects the on-chip program against software piracy. Program ROM Lock Bits Table 46. Program Lock bits Program Lock Bits Protection Description Security level LB0 LB1 1 U U No program lock features enabled. 2 P U Reserved. Do not use. 3 U P MOVC instruction executed from external program memory are disabled from fetching code bytes from internal memory, EA is sampled and latched on reset. Verify disable. Notes: 1. U: unprogrammed P: programmed 2. The lock bits when programmed according to Table 46 will provide different level of protection for the on-chip code and data. 63 4113B–8051–03/05 Power-off Flag The Power-off flag allows the user to distinguish between a “cold start” reset and a “warm start” reset. A cold start reset is the one induced by VCC switch-on. A warm start reset occurs while VCC is still applied to the device and could be generated for example by an exit from power-down. The Power-off flag (POF) is located in PCON register (Table 47). POF is set by hardware when VCC rises from 0 to its nominal voltage. The POF can be set or cleared by software allowing the user to determine the type of reset. Table 47. PCON Register PCON - Power Control Register (87h) 7 6 5 4 3 2 1 0 SMOD1 SMOD0 - POF GF1 GF0 PD IDL Bit Number Bit Mnemonic Description 7 SMOD1 Serial port Mode bit 1 Set to select double baud rate in mode 1, 2 or 3. 6 SMOD0 Serial port Mode bit 0 Cleared to select SM0 bit in SCON register. Set to select FE bit in SCON register. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 POF Power-off Flag Cleared to recognize next reset type. Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by software. 3 GF1 General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. 2 GF0 General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. 1 PD Power-down mode bit Cleared by hardware when reset occurs. Set to enter power-down mode. 0 IDL Idle mode bit Cleared by hardware when interrupt or reset occurs. Set to enter idle mode. Reset Value = 00X1 0000b Not bit addressable 64 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Reduced EMI Mode The ALE signal is used to demultiplex address and data buses on port 0 when used with external program or data memory. Nevertheless, during internal code execution, ALE signal is still generated. In order to reduce EMI, ALE signal can be disabled by setting AO bit. The AO bit is located in AUXR register at bit location 0. As soon as AO is set, ALE is no longer output but remains active during MOVX and MOVC instructions and external fetches. During ALE disabling, ALE pin is weakly pulled high. Table 48. AUXR Register AUXR - Auxiliary Register (8Eh) 7 6 5 4 3 2 1 0 - - M0 - XRS1 XRS0 EXTRAM AO Bit Number Bit Mnemonic Description 7 - 6 - Reserved The value read from this bit is indeterminate. Do not set this bit Reserved The value read from this bit is indeterminate. Do not set this bit Pulse length Cleared to stretch MOVX control: the RD and the WR pulse length is 6 clock periods (default). Set to stretch MOVX control: the RD and the WR pulse length is 30 clock periods. 5 M0 4 - 3 XRS1 XRAM Size XRS0 XRS1 0 0 1 1 2 Reserved The value read from this bit is indeterminate. Do not set this bit XRS0 0 1 0 1 XRAM Size 256 bytes (default) 512 bytes 768 bytes 1024 bytes EXTRAM bit Cleared to access internal XRAM using movx @ Ri/ @ DPTR. 1 0 EXTRAM AO Set to access external memory. Programmed by hardware after Power-up regarding Hardware Security Byte (HSB), default setting, XRAM selected. ALE Output bit Cleared, ALE is emitted at a constant rate of 1/6 the oscillator frequency (or 1/3 if X2 mode is used) (default). Set, ALE is active only during a MOVX or MOVC instructione is used. 65 4113B–8051–03/05 Electrical Characteristics Absolute Maximum Ratings Note: C = commercial......................................................0°C to 70°C I = industrial ........................................................-40°C to 85°C Storage Temperature .................................... -65°C to + 150°C Voltage on VCC to VSS (standard voltage) .........-0.5V to + 6.5V Voltage on VCC to VSS (low voltage)..................-0.5V to + 4.5V Voltage on Any Pin to VSS ..........................-0.5V to VCC + 0.5V Power Dissipation .............................................................. 1 W Stresses at or above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Power dissipation value is based on the maximum allowable die temperature and the thermal resistance of the package. DC Parameters for Standard Voltage TA = 0°C to +70°C; VSS = 0V; VCC = 4.5V to 5.5V; F = 10 to 40 MHz TA = -40°C to +85°C; VSS = 0V; VCC =4.5V to 5.5V; F = 10 to 40 MHz Symbol Parameter Min VIL Input Low Voltage VIH Input High Voltage except RST, XTAL1 VIH1 Input High Voltage RST, XTAL1 VOL Output Low Voltage, ports 1, 2, 3, 4 (6) Max Unit -0.5 0.2 VCC - 0.1 V 0.2 VCC + 0.9 VCC + 0.5 V 0.7 VCC VCC + 0.5 V 0.3 0.45 1.0 V V V IOL = 100 µA(4) IOL = 1.6 mA(4) IOL = 3.5 mA(4) 0.3 0.45 1.0 V V V IOL = 200 µA(4) IOL = 3.2 mA(4) IOL = 7.0 mA(4) Output High Voltage, ports 1, 2, 3, 4 VCC - 0.3 VCC - 0.7 VCC - 1.5 V V V IOH = -10 µA IOH = -30 µA IOH = -60 µA VCC = 5V ± 10% VOH1 Output High Voltage, port 0, ALE, PSEN VCC - 0.3 VCC - 0.7 VCC - 1.5 V V V IOH = -200 µA IOH = -3.2 mA IOH = -7.0 mA VCC = 5V ± 10% RRST RST Pull-down Resistor VOL1 VOH 66 Output Low Voltage, port 0, ALE, PSEN Typ (6) 50 200(5) 250 kΩ Test Conditions IIL Logical 0 Input Current ports 1, 2, 3, 4 and 5 -50 µA VIN = 0.45V ILI Input Leakage Current ±10 µA 0.45V < VIN < VCC ITL Logical 1 to 0 Transition Current, ports 1, 2, 3, 4 -650 µA VIN = 2.0 V CIO Capacitance of I/O Buffer 10 pF Fc = 3 MHz TA = 25°C IPD Power-down Current 150 µA 4.5V < VCC < 5.5V(3) 100 ICCOP Power Supply Current on normal mode 0.29 x Frequency (MHz) + 4 mA VCC = 5.5V(1) ICCIDLE Power Supply Current on idle mode 0.16 x Frequency (MHz) + 4 mA VCC = 5.5V(2) AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 DC Parameters for Standard Voltage (2) TA = 0°C to +70°C; VSS = 0 V; VCC = 2.7V to 5.5V; F = 10 to 40 MHz TA = -40°C to +85°C; VSS = 0 V; VCC = 2.7V to 5.5V; F = 10 to 40 MHz Symbol Parameter Min VIL Input Low Voltage VIH Input High Voltage except XTAL1, RST VIH1 Input High Voltage, XTAL1, RST Typ(5) Max Unit -0.5 0.2 VCC - 0.1 V 0.2 VCC + 0.9 VCC + 0.5 V 0.7 VCC VCC + 0.5 V 0.45 V IOL = 0.8 mA(4) 0.45 V IOL = 1.6 mA(4) (6) Test Conditions VOL Output Low Voltage, ports 1, 2, 3, 4 and 5 VOL1 Output Low Voltage, port 0, ALE, PSEN (6) VOH Output High Voltage, ports 1, 2, 3, 4 and 5 0.9 VCC V IOH = -10 µA VOH1 Output High Voltage, port 0, ALE, PSEN 0.9 VCC V IOH = -40 µA IIL Logical 0 Input Current ports 1, 2, 3, 4 and 5 -50 µA VIN = 0.45V ILI Input Leakage Current ±10 µA 0.45V < VIN < VCC ITL Logical 1 to 0 Transition Current, ports 1, 2, 3, 4 and 5 -650 µA VIN = 2.0V 250 kΩ 10 pF Fc = 3 MHz TA = 25°C 150 µA VCC =2.7V to 5.5V(3) RRST RST Pulldown Resistor CIO Capacitance of I/O Buffer IPD Power-down Current 50 200 120 ICCOP Power Supply Current on normal mode 0.29 x Frequency (MHz) + 4 mA VCC = 5.5V(1) ICCIDLE Power Supply Current on idle mode 0.16 x Frequency (MHz) + 4 mA VCC = 5.5V(2) 67 4113B–8051–03/05 DC Parameters for Low Voltage TA = 0°C to +70°C; VSS = 0V; VCC = 2.7V to 3.6V; F = 10 to 40 MHz TA = -40°C to +85°C; VSS = 0V; VCC = 2.7V to 3.6V; F = 10 to 40 MHz Symbol Parameter Min VIL Input Low Voltage VIH Input High Voltage except RST, XTAL1 VIH1 Input High Voltage, RST, XTAL1 Max Unit -0.5 0.2 VCC - 0.1 V 0.2 VCC + 0.9 VCC + 0.5 V 0.7 VCC VCC + 0.5 V (6) Test Conditions VOL Output Low Voltage, ports 1, 2, 3, 4 0.45 V IOL = 0.8 mA(4) VOL1 Output Low Voltage, port 0, ALE, PSEN (6) 0.45 V IOL = 1.6 mA(4) VOH Output High Voltage, ports 1, 2, 3, 4 0.9 VCC V IOH = -10 µA VOH1 Output High Voltage, port 0, ALE, PSEN 0.9 VCC V IOH = -40 µA IIL Logical 0 Input Current ports 1, 2, 3, 4 -50 µA VIN = 0.45V ILI Input Leakage Current ±10 µA 0.45V < VIN < VCC ITL Logical 1 to 0 Transition Current, ports 1, 2, 3, -650 µA VIN = 2.0V 250 kΩ 10 pF Fc = 3 MHz TA = 25°C 50 µA VCC = 2.7V to 3.6V(3) RRST RST Pulldown Resistor CIO Capacitance of I/O Buffer IPD Power-down Current 50 200 (5) 10 (5) ICCOP Power Supply Current on normal mode 0.31 x Frequency (MHz) + 4 mA VCC = 3.6V(1) ICCIDLE Power Supply Current on idle mode 0.2 x Frequency (MHz) + 4 mA VCC = 3.6V(2) Notes: 68 Typ 1. Operating ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (see Figure 26.), VIL = VSS + 0.5V, VIH = VCC - 0.5V; XTAL2 N.C.; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used (see Figure 23). 2. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 0.5V, VIH = VCC - 0.5V; XTAL2 N.C; Port 0 = VCC; EA = RST = VSS (see Figure 24). 3. Power-down ICC is measured with all output pins disconnected; EA = VSS, PORT 0 = VCC; XTAL2 NC.; RST = VSS (see Figure 25). 4. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1 and 3. The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operation. In the worst cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed 0.45V with maxi VOL peak 0.6V. A Schmitt Trigger use is not necessary. 5. Typical are based on a limited number of samples and are not guaranteed. The values listed are at room temperature and 5V. 6. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10 mA Maximum IOL per 8-bit port: Port 0: 26 mA Ports 1, 2 and 3: 15 mA Maximum total IOL for all output pins: 71 mA If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 7. For other values, please contact your sales office. AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Figure 23. ICC Test Condition, Active Mode VCC ICC VCC VCC P0 VCC RST EA XTAL2 XTAL1 (NC) CLOCK SIGNAL VSS All other pins are disconnected. Figure 24. ICC Test Condition, Idle Mode VCC ICC VCC VCC P0 RST EA XTAL2 XTAL1 VSS (NC) CLOCK SIGNAL All other pins are disconnected. Figure 25. ICC Test Condition, Power-down Mode VCC ICC VCC VCC P0 RST (NC) EA XTAL2 XTAL1 VSS All other pins are disconnected. Figure 26. Clock Signal Waveform for ICC Tests in Active and Idle Modes VCC-0.5V 0.45V TCLCH TCHCL TCLCH = TCHCL = 5ns. 0.7VCC 0.2VCC-0.1 69 4113B–8051–03/05 AC Parameters Explanation of the AC Symbols Each timing symbol has 5 characters. The first character is always a “t” (stands for time). The other characters, depending on their positions, stand for the name of a signal or the logical status of that signal. The following is a list of all the characters and what they stand for. Example:TAVLL = Time for Address Valid to ALE Low. TLLPL = Time for ALE Low to PSEN Low. (Load Capacitance for port 0, ALE and PSEN = 100 pF; Load Capacitance for all other outputs = 80 pF.) Table 49 Table 52, and Table 54 give the description of each AC symbols. Table 51, Table 53 and Table 55 give for each range the AC parameter. Table 50, Table 51 and Table 56 gives the frequency derating formula of the AC parameter for each speed range description. To calculate each AC symbols. take the x value in the correponding column (-M or -L) and use this value in the formula. Example: TLLIU for -M and 20 MHz, Standard clock. x = 35 ns T = 50 ns TCCIV = 4T - x = 165 ns External Program Memory Characteristics Table 49. Symbol Description Symbol T 70 Parameter Oscillator clock period TLHLL ALE pulse width TAVLL Address Valid to ALE TLLAX Address Hold After ALE TLLIV ALE to Valid Instruction In TLLPL ALE to PSEN TPLPH PSEN Pulse Width TPLIV PSEN to Valid Instruction In TPXIX Input Instruction Hold After PSEN TPXIZ Input Instruction FloatAfter PSEN TAVIV Address to Valid Instruction In TPLAZ PSEN Low to Address Float AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 50. AC Parameters for a Fix Clock Symbol -M -L Min Max Min Units Max T 25 25 ns TLHLL 35 35 ns TAVLL 5 5 ns TLLAX 5 5 ns 65 TLLIV 65 ns TLLPL 5 5 ns TPLPH 50 50 ns 30 TPLIV 30 0 TPXIX 0 ns ns TPXIZ 10 10 ns TAVIV 80 80 ns TPLAZ 10 10 ns Table 51. AC Parameters for a Variable Clock Symbol Type Standard Clock X2 Clock X Parameter for M Range X Parameter for -L Range Units TLHLL Min 2T-x T-x 15 15 ns TAVLL Min T-x 0.5 T - x 20 20 ns TLLAX Min T-x 0.5 T - x 20 20 ns TLLIV Max 4T-x 2T-x 35 35 ns TLLPL Min T-x 0.5 T - x 15 15 ns TPLPH Min 3T-x 1.5 T - x 25 25 ns TPLIV Max 3T-x 1.5 T - x 45 45 ns TPXIX Min x x 0 0 ns TPXIZ Max T-x 0.5 T - x 15 15 ns TAVIV Max 5T-x 2.5 T - x 45 45 ns TPLAZ Max x x 10 10 ns 71 4113B–8051–03/05 External Program Memory Read Cycle 12 TCLCL TLHLL TLLIV ALE TLLPL TPLPH PSEN TLLAX TAVLL PORT 0 INSTR IN TPXAV TPXIZ TPLIV TPLAZ A0-A7 TPXIX INSTR IN A0-A7 INSTR IN TAVIV PORT 2 External Data Memory Characteristics ADDRESS OR SFR-P2 ADDRESS A8 - A15 Table 52. Symbol Description Symbol 72 ADDRESS A8-A15 Parameter TRLRH RD Pulse Width TWLWH WR Pulse Width TRLDV RD to Valid Data In TRHDX Data Hold After RD TRHDZ Data Float After RD TLLDV ALE to Valid Data In TAVDV Address to Valid Data In TLLWL ALE to WR or RD TAVWL Address to WR or RD TQVWX Data Valid to WR Transition TQVWH Data set-up to WR High TWHQX Data Hold After WR TRLAZ RD Low to Address Float TWHLH RD or WR High to ALE high AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Table 53. AC Parameters for a Fix Clock -M -L Symbol Min TRLRH 125 125 ns TWLWH 125 125 ns Min 95 TRLDV TRHDX Max 0 Max 95 0 Units ns ns TRHDZ 25 25 ns TLLDV 155 155 ns TAVDV 160 160 ns 105 ns TLLWL 45 105 TAVWL 70 70 ns TQVWX 5 5 ns TQVWH 155 155 ns TWHQX 10 10 ns TRLAZ 0 0 ns TWHLH 5 45 45 5 45 ns 73 4113B–8051–03/05 Symbol Type Standard Clock X2 Clock X parameter for M range X parameter for L range Units TRLRH Min 6T-x 3T-x 25 25 ns TWLWH Min 6T-x 3T-x 25 25 ns TRLDV Max 5T-x 2.5 T - x 30 30 ns TRHDX Min x x 0 0 ns TRHDZ Max 2T-x T-x 25 25 ns TLLDV Max 8T-x 4T -x 45 45 ns TAVDV Max 9T-x 4.5 T - x 65 65 ns TLLWL Min 3T-x 1.5 T - x 30 30 ns TLLWL Max 3T+x 1.5 T + x 30 30 ns TAVWL Min 4T-x 2T-x 30 30 ns TQVWX Min T-x 0.5 T - x 20 20 ns TQVWH Min 7T-x 3.5 T - x 20 20 ns TWHQX Min T-x 0.5 T - x 15 15 ns TRLAZ Max x x 0 0 ns TWHLH Min T-x 0.5 T - x 20 20 ns TWHLH Max T+x 0.5 T + x 20 20 ns External Data Memory Write Cycle TWHLH ALE PSEN TLLWL TWLWH WR TQVWX TLLAX PORT 0 A0-A7 TQVWH TWHQX DATA OUT TAVWL PORT 2 74 ADDRESS OR SFR-P2 ADDRESS A8 - A15 OR SFR P2 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 External Data Memory Read Cycle TWHLH TLLDV ALE PSEN TLLWL TRLRH RD TRHDZ TAVDV TLLAX PORT 0 TRHDX A0-A7 DATA IN TRLAZ TAVWL PORT 2 ADDRESS OR SFR-P2 Serial Port Timing - Shift Register Mode ADDRESS A8-A15 OR SFR P2 Table 54. Symbol Description Symbol Parameter TXLXL Serial port clock cycle time TQVHX Output data set-up to clock rising edge TXHQX Output data hold after clock rising edge TXHDX Input data hold after clock rising edge TXHDV Clock rising edge to input data valid Table 55. AC Parameters for a Fix Clock -M -L Symbol Min Max Min Max TXLXL 300 300 ns TQVHX 200 200 ns TXHQX 30 30 ns TXHDX 0 0 ns 117 TXHDV Units 117 ns Table 56. AC Parameters for a Variable Clock Symbol Type Standard Clock X2 Clock X Parameter for M Range X Parameter for -L Range TXLXL Min 12 T 6T TQVHX Min 10 T - x 5T-x 50 50 ns TXHQX Min 2T-x T-x 20 20 ns TXHDX Min x x 0 0 ns TXHDV Max 10 T - x 5 T- x 133 133 ns Units ns 75 4113B–8051–03/05 Shift Register Timing Waveforms INSTRUCTION 0 1 2 3 4 5 6 7 8 ALE TXLXL CLOCK TXHQX TQVXH 0 OUTPUT DATA 1 2 INPUT DATA 4 5 6 7 TXHDX TXHDV WRITE to SBUF 3 VALID VALID SET TI VALID VALID VALID VALID VALID VALID SET RI CLEAR RI External Clock Drive Waveforms VCC-0.5V 0.45V 0.7VCC 0.2VCC-0.1 TCHCL TCHCX TCLCH TCLCX TCLCL AC Testing Input/Output Waveforms VCC -0.5V 0.2 VCC + 0.9 INPUT/OUTPUT 0.2 VCC - 0.1 0.45V AC inputs during testing are driven at VCC - 0.5 for a logic “1” and 0.45V for a logic “0”. Timing measurement are made at VIH min for a logic “1” and VIL max for a logic “0”. Float Waveforms FLOAT VOH - 0.1 V VOL + 0.1 V VLOAD VLOAD + 0.1 V VLOAD - 0.1 V For timing purposes as port pin is no longer floating when a 100 mV changes from load voltage occurs and begins to float when a 100 mV change from the loaded VOH/VOL level occurs. IOL/IOH ≥ ± 20 mA. Clock Waveforms 76 Valid in normal clock mode. In X2 mode XTAL2 must be changed to XTAL2/2. AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Figure 27. Internal Clock Signals INTERNAL CLOCK STATE4 STATE5 STATE6 STATE1 STATE2 STATE3 STATE4 STATE5 P1 P1 P1 P1 P1 P1 P1 P1 P2 P2 P2 P2 P2 P2 P2 P2 XTAL2 ALE THESE SIGNALS ARE NOT ACTIVATED DURING THE EXECUTION OF A MOVX INSTRUCTION EXTERNAL PROGRAM MEMORY FETCH PSEN P0 DATA SAMPLED FLOAT P2 (EXT) PCL OUT DATA SAMPLED FLOAT PCL OUT DATA SAMPLED FLOAT PCL OUT INDICATES ADDRESS TRANSITIONS READ CYCLE RD PCL OUT (IF PROGRAM MEMORY IS EXTERNAL) P0 DPL OR Rt OUT P2 DATA SAMPLED FLOAT INDICATES DPH OR P2 SFR TO PCH TRANSITION WRITE CYCLE WR P0 PCL OUT (EVEN IF PROGRAM MEMORY IS INTERNAL) DPL OR Rt OUT PCL OUT (IF PROGRAM MEMORY IS EXTERNAL) DATA OUT P2 INDICATES DPH OR P2 SFR TO PCH TRANSITION PORT OPERATION MOV PORT SRC OLD DATA NEW DATA P0 PINS SAMPLED P0 PINS SAMPLED MOV DEST P0 MOV DEST PORT (P1. P2. P3) (INCLUDES INTO. INT1. TO T1) SERIAL PORT SHIFT CLOCK P1, P2, P3 PINS SAMPLED RXD SAMPLED P1, P2, P3 PINS SAMPLED RXD SAMPLED TXD (MODE 0) This diagram indicates when signals are clocked internally. The time it takes the signals to propagate to the pins, however, ranges from 25 to 125 ns. This propagation delay is dependent on variables such as temperature and pin loading. Propagation also varies from output to output and component. Typically though (TA = 25°C fully loaded) RD and WR propagation delays are approximately 50 ns. The other signals are typically 85 ns. Propagation delays are incorporated in the AC specifications. 77 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Ordering Information Table 57. Ordering Information Part Number Memory Size Supply Voltage Package Temperature Range Packing AT80C51RD2-3CSCM PDIL40 Commercial Stick AT80C51RD2-3CSIM PDIL40 Industrial Stick AT80C51RD2-SLSCM PLCC44 Commercial Stick PLCC44 Industrial Stick VQFP44 Industrial Tray PDIL40 Industrial & Green Stick AT80C51RD2-SLSUM PLCC44 Industrial & Green Stick AT80C51RD2-RLTUM VQFP44 Industrial & Green Tray AT80C51RD2-SLSIL PLCC44 Industrial Stick VQFP44 Industrial Tray AT80C51RD2-SLSUL PLCC44 Industrial & Green Stick AT80C51RD2-RLTUL VQFP44 Industrial & Green Tray AT80C51RD2-SLSIM 5V AT80C51RD2-RLTIM AT80C51RD2-3CSUM ROMLess AT80C51RD2-RLTIL 3V 78 4113B–8051–03/05 Table 57. Ordering Information (Continued) Part Number Memory Size Supply Voltage Package Temperature Range Packing AT83C51RB2xxx-3CSCM PDIL40 Commercial Stick AT83C51RB2xxx-3CSIM PDIL40 Industrial Stick AT83C51RB2xxx-SLSCM PLCC44 Commercial Stick AT83C51RB2xxx-SLSIM PLCC44 Industrial Stick AT83C51RB2xxx-RLTIM VQFP44 Industrial Tray PDIL40 Industrial & Green Stick PLCC44 Industrial & Green Stick VQFP44 Industrial & Green Tray AT83C51RC2xxx-3CSUM PDIL40 Industrial & Green Stick AT83C51RC2xxx-SLSUM PLCC44 Industrial & Green Stick AT83C51RC2xxx-RLTUM VQFP44 Industrial & Green Tray AT83C51RB2xxx-SLSIL PLCC44 Industrial Stick VQFP44 Industrial Tray AT83C51RB2xxx-SLSUL PLCC44 Industrial & Green Stick AT83C51RB2xxx-RLTUL VQFP44 Industrial & Green Tray Package Temperature Range Packing AT83C51RC2xxx-3CSCM PDIL40 Commercial Stick AT83C51RC2xxx-3CSIM PDIL40 Industrial Stick PLCC44 Commercial Stick PLCC44 Industrial Stick VQFP44 Industrial Tray VQFP44 Industrial Tray PLCC44 Industrial Stick AT83C51RC2xxx-RLTUL VQFP44 Industrial & Green Tray AT83C51RC2xxx-SLSUL PLCC44 Industrial & Green Stick 5V AT83C51RB2xxx-3CSUM AT83C51RB2xxx-SLSUM AT83C51RB2xxx-RLTUM 16K bytes AT83C51RB2xxx-RLTIL 3V Part Number Memory Size Supply Voltage AT83C51RC2xxx-SLSCM 5V AT83C51RC2xxx-SLSIM AT83C51RC2xxx-RLTIM 32K bytes AT83C51RC2xxx-RLTIL AT83C51RC2xxx-SLSIL 3V 79 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 Package Information PDIL40 80 4113B–8051–03/05 PLCC44 VQFP44 81 AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 AT80C51RD2/AT83C51Rx2 82 4113B–8051–03/05 Datasheet Change Log Changes from 4113A 09/02 to 4113B -03/05 83 1. Added Green product ordering information. AT80C51RD2/AT83C51Rx2 4113B–8051–03/05 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © Atmel Corporation 2005 . All rights reserved. Atmel®, logo and combinations thereof, are registered trademarks, and Everywhere You AreSM are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 4113B–8051–03/05 /xM