Intersil ISL61852DCRZ Dual usb port power supply controller Datasheet

Dual USB Port Power Supply Controller
ISL6185
Features
The ISL6185 USB power controller family provides fully
independent overcurrent (OC) fault protection for two or more
USB ports.
• 2.5V to 5V Operating Range
This product family consists of sixteen individual functional
product variants and three package options. It is operation
rated for a nominal +2.5V to +5V range and is specified over the
full commercial and industrial temperature ranges.
Each ISL6185 type incorporates in a single package two 71mΩ
P-channel MOSFET power switches for power control. Each
features internal current monitoring, accurate current limiting,
and current limited delay to turn-off, for system supply
protection along with control and communication I/O.
The ISL6185 family offers product variants with specified
continuous output current levels of 0.6A, 1.1A, 1.5A or 1.8A; enable
active high or low inputs; and latch off or automatic retry after
overcurrent turn-off, making these devices well suited for many
low-power applications.
This family of ICs is offered in an industry-standard SOIC pinout
and also in the 70% smaller 3x3 DFN packages providing similar
or enhanced performance in the smallest possible package.
• 71mΩ Integrated Power P-channel MOSFET Switches
• Continuous Current Options for 0.6A, 1.1A, 1.5A and 1.8A
• Thermally Insensitive 12ms of Current Limiting Prior to
Turn-Off
• Output Discharges with Reverse Current Blocking When
Disabled
• Latch-off or Auto Restart Options
• 1µA Off-State Supply Current
• Enable Polarity Options
• Industry-standard Pin for Pin SOIC, and Smaller DFN Packages
Available
• UL Recognized, File Number: E333469
Applications
• USB 1, 2, 3 Port Power Management
• Low Power (18W) Electronic Circuit Limiting and Breaker
D+
D-
C
O
N
T
R
O
L
L
E
R
ENABLE_1
USB
PORT 1
OUT_1
VBUS
FAULT_1
+5V
VIN
GND
ISL6185
FAULT_2
ENABLE_2
OUT_2
D+
DUSB PORT POWER
FIGURE 1. TYPICAL APPLICATION
March 8, 2012
FN6937.3
1
VBUS
USB
PORT_2
1.3
NORMALIZED rDS(ON)
U
S
B
1.2
1.1
1.0
0.9
0.8
0.7
-40
-25
0
25
45
75
TEMPERATURE (°C)
85
115
FIGURE 2. NORMALIZED rDS(ON) TEMPERATURE
CHARACTERISTIC CURVE
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2010, 2011, 2012. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
ISL6185
Simplified Block Diagram
CHANNEL 1 LIKE CHANNEL 2
FAULT_1
GND
+
-V
comp
OUT_1
VIN
POR
CURRENT AND TEMP.
MONITORING, GATE,
DELAY & OUTPUT CONTROL
LOGIC
EN_1
EN_2
OUT_2
FAULT_2
Ordering Information
PART
NUMBER
(Notes 1, 2, 3)
PART MARKING
EN/EN
INPUT
VIN = 5V
MAXIMUM
CONTINUOUS IOUT
(A)
LATCH/AUTO
RETRY
TEMP.
RANGE (°C)
PACKAGE
(Pb-free)
PKG.
DWG. #
ISL61851ACBZ
61851A CBZ
EN
0.6
LATCH
0 to +70
8 Lead SOIC
M8.15
ISL61851BCBZ
61851B CBZ
EN
0.6
RETRY
0 to +70
8 Lead SOIC
M8.15
ISL61851CCBZ
61851C CBZ
EN
1.1
LATCH
0 to +70
8 Lead SOIC
M8.15
ISL61851DCBZ
61851D CBZ
EN
1.1
RETRY
0 to +70
8 Lead SOIC
M8.15
ISL61851ECBZ
61851E CBZ
EN
0.6
LATCH
0 to +70
8 Lead SOIC
M8.15
ISL61851FCBZ
61851F CBZ
EN
0.6
RETRY
0 to +70
8 Lead SOIC
M8.15
ISL61851GCBZ
61851G CBZ
EN
1.1
LATCH
0 to +70
8 Lead SOIC
M8.15
ISL61851HCBZ
61851H CBZ
EN
1.1
RETRY
0 to +70
8 Lead SOIC
M8.15
ISL61851ICBZ
61851I CBZ
EN
1.5
LATCH
0 to +70
8 Lead SOIC
M8.15
ISL61851JCBZ
61851J CBZ
EN
1.5
RETRY
0 to +70
8 Lead SOIC
M8.15
ISL61851KCBZ
61851K CBZ
EN
1.5
LATCH
0 to +70
8 Lead SOIC
M8.15
ISL61851LCBZ
61851L CBZ
EN
1.5
RETRY
0 to +70
8 Lead SOIC
M8.15
ISL61852ACRZ
52AC
EN
0.6
LATCH
0 to +70
8 Lead DFN
L8.3x3J
ISL61852BCRZ
52BC
EN
0.6
RETRY
0 to +70
8 Lead DFN
L8.3x3J
ISL61852CCRZ
52CC
EN
1.1
LATCH
0 to +70
8 Lead DFN
L8.3x3J
ISL61852DCRZ
52DC
EN
1.1
RETRY
0 to +70
8 Lead DFN
L8.3x3J
ISL61852ECRZ
52EC
EN
0.6
LATCH
0 to +70
8 Lead DFN
L8.3x3J
2
FN6937.3
March 8, 2012
ISL6185
Ordering Information (Continued)
PART
NUMBER
(Notes 1, 2, 3)
ISL61852FCRZ
PART MARKING
52FC
EN/EN
INPUT
VIN = 5V
MAXIMUM
CONTINUOUS IOUT
(A)
LATCH/AUTO
RETRY
TEMP.
RANGE (°C)
EN
0.6
RETRY
0 to +70
8 Lead DFN
L8.3x3J
PACKAGE
(Pb-free)
PKG.
DWG. #
ISL61852GCRZ
52GC
EN
1.1
LATCH
0 to +70
8 Lead DFN
L8.3x3J
ISL61852HCRZ
52HC
EN
1.1
RETRY
0 to +70
8 Lead DFN
L8.3x3J
ISL61852ICRZ
52IC
EN
1.5
LATCH
0 to +70
8 Lead DFN
L8.3x3J
ISL61852JCRZ
52JC
EN
1.5
RETRY
0 to +70
8 Lead DFN
L8.3x3J
ISL61852KCRZ
52KC
EN
1.5
LATCH
0 to +70
8 Lead DFN
L8.3x3J
ISL61852LCRZ
52LC
EN
1.5
RETRY
0 to +70
8 Lead DFN
L8.3x3J
ISL61853ACRZ
53AC
EN
0.6
LATCH
0 to +70
10 Lead DFN
L10.3x3
ISL61853BCRZ
53BC
EN
0.6
RETRY
0 to +70
10 Lead DFN
L10.3x3
ISL61853CCRZ
53CC
EN
1.1
LATCH
0 to +70
10 Lead DFN
L10.3x3
ISL61853DCRZ
53DC
EN
1.1
RETRY
0 to +70
10 Lead DFN
L10.3x3
ISL61853ECRZ
53EC
EN
0.6
LATCH
0 to +70
10 Lead DFN
L10.3x3
ISL61853FCRZ
53FC
EN
0.6
RETRY
0 to +70
10 Lead DFN
L10.3x3
ISL61853GCRZ
53GC
EN
1.1
LATCH
0 to +70
10 Lead DFN
L10.3x3
ISL61853HCRZ
53HC
EN
1.1
RETRY
0 to +70
10 Lead DFN
L10.3x3
ISL61853ICRZ
53IC
EN
1.5
LATCH
0 to +70
10 Lead DFN
L10.3x3
ISL61853JCRZ
53JC
EN
1.5
RETRY
0 to +70
10 Lead DFN
L10.3x3
ISL61853KCRZ
53KC
EN
1.5
LATCH
0 to +70
10 Lead DFN
L10.3x3
ISL61853LCRZ
53LC
EN
1.5
RETRY
0 to +70
10 Lead DFN
L10.3x3
ISL61853MCRZ
53MC
EN
1.8
LATCH
0 to +70
10 Lead DFN
L10.3x3
ISL61853NCRZ
53NC
EN
1.8
RETRY
0 to +70
10 Lead DFN
L10.3x3
ISL61853OCRZ
53OC
EN
1.8
LATCH
0 to +70
10 Lead DFN
L10.3x3
ISL61853PCRZ
53PC
EN
1.8
RETRY
0 to +70
10 Lead DFN
L10.3x3
ISL61851AIBZ
61851A IBZ
EN
0.6
LATCH
-40 to +85
8 Lead SOIC
M8.15
ISL61851BIBZ
61851B IBZ
EN
0.6
RETRY
-40 to +85
8 Lead SOIC
M8.15
ISL61851CIBZ
61851C IBZ
EN
1.1
LATCH
-40 to +85
8 Lead SOIC
M8.15
ISL61851DIBZ
61851D IBZ
EN
1.1
RETRY
-40 to +85
8 Lead SOIC
M8.15
ISL61851EIBZ
61851E IBZ
EN
0.6
LATCH
-40 to +85
8 Lead SOIC
M8.15
ISL61851FIBZ
61851F IBZ
EN
0.6
RETRY
-40 to +85
8 Lead SOIC
M8.15
ISL61851GIBZ
61851G IBZ
EN
1.1
LATCH
-40 to +85
8 Lead SOIC
M8.15
ISL61851HIBZ
61851H IBZ
EN
1.1
RETRY
-40 to +85
8 Lead SOIC
M8.15
ISL61851IIBZ
61851I IBZ
EN
1.5
LATCH
-40 to +85
8 Lead SOIC
M8.15
ISL61851JIBZ
61851J IBZ
EN
1.5
RETRY
-40 to +85
8 Lead SOIC
M8.15
ISL61851KIBZ
61851K IBZ
EN
1.5
LATCH
-40 to +85
8 Lead SOIC
M8.15
ISL61851LIBZ
61851L IBZ
EN
1.5
RETRY
-40 to +85
8 Lead SOIC
M8.15
ISL61852AIRZ
52AI
EN
0.6
LATCH
-40 to +85
8 Lead DFN
L8.3x3J
ISL61852BIRZ
52BI
EN
0.6
RETRY
-40 to +85
8 Lead DFN
L8.3x3J
ISL61852CIRZ
52CI
EN
1.1
LATCH
-40 to +85
8 Lead DFN
L8.3x3J
ISL61852DIRZ
52DI
EN
1.1
RETRY
-40 to +85
8 Lead DFN
L8.3x3J
ISL61852EIRZ
52EI
EN
0.6
LATCH
-40 to +85
8 Lead DFN
L8.3x3J
3
FN6937.3
March 8, 2012
ISL6185
Ordering Information (Continued)
PART
NUMBER
(Notes 1, 2, 3)
ISL61852FIRZ
EN/EN
INPUT
VIN = 5V
MAXIMUM
CONTINUOUS IOUT
(A)
LATCH/AUTO
RETRY
TEMP.
RANGE (°C)
52FI
EN
0.6
RETRY
-40 to +85
8 Lead DFN
L8.3x3J
PART MARKING
PACKAGE
(Pb-free)
PKG.
DWG. #
ISL61852GIRZ
52GI
EN
1.1
LATCH
-40 to +85
8 Lead DFN
L8.3x3J
ISL61852HIRZ
52HI
EN
1.1
RETRY
-40 to +85
8 Lead DFN
L8.3x3J
ISL61852IIRZ
52II
EN
1.5
LATCH
-40 to +85
8 Lead DFN
L8.3x3J
ISL61852JIRZ
52JI
EN
1.5
RETRY
-40 to +85
8 Lead DFN
L8.3x3J
ISL61852KIRZ
52KI
EN
1.5
LATCH
-40 to +85
8 Lead DFN
L8.3x3J
ISL61852LIRZ
52LI
EN
1.5
RETRY
-40 to +85
8 Lead DFN
L8.3x3J
ISL61853AIRZ
53AI
EN
0.6
LATCH
-40 to +85
10 Lead DFN
L10.3x3
ISL61853BIRZ
53BI
EN
0.6
RETRY
-40 to +85
10 Lead DFN
L10.3x3
ISL61853CIRZ
53CI
EN
1.1
LATCH
-40 to +85
10 Lead DFN
L10.3x3
ISL61853DIRZ
53DI
EN
1.1
RETRY
-40 to +85
10 Lead DFN
L10.3x3
ISL61853EIRZ
53EI
EN
0.6
LATCH
-40 to +85
10 Lead DFN
L10.3x3
ISL61853FIRZ
53FI
EN
0.6
RETRY
-40 to +85
10 Lead DFN
L10.3x3
ISL61853GIRZ
53GI
EN
1.1
LATCH
-40 to +85
10 Lead DFN
L10.3x3
ISL61853HIRZ
53HI
EN
1.1
RETRY
-40 to +85
10 Lead DFN
L10.3x3
ISL61853IIRZ
53II
EN
1.5
LATCH
-40 to +85
10 Lead DFN
L10.3x3
ISL61853JIRZ
53JI
EN
1.5
RETRY
-40 to +85
10 Lead DFN
L10.3x3
ISL61853KIRZ
53KI
EN
1.5
LATCH
-40 to +85
10 Lead DFN
L10.3x3
ISL61853LIRZ
53LI
EN
1.5
RETRY
-40 to +85
10 Lead DFN
L10.3x3
ISL61853MIRZ
53MI
EN
1.8
LATCH
-40 to +85
10 Lead DFN
L10.3x3
ISL61853NIRZ
53NI
EN
1.8
RETRY
-40 to +85
10 Lead DFN
L10.3x3
ISL61853OIRZ
53OI
EN
1.8
LATCH
-40 to +85
10 Lead DFN
L10.3x3
ISL61853PIRZ
53PI
EN
1.8
RETRY
-40 to +85
10 Lead DFN
L10.3x3
ISL61851EVAL1Z
8 Lead SOIC Evaluation Platform with ISL61851A installed
ISL61852EVAL1Z
8 Lead DFN Evaluation Platform with ISL61852H installed
ISL61853EVAL1Z
10 Lead DFN Evaluation Platform with ISL61853I installed
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pbfree products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information pages for ISL6185XXC (commercial version) and ISL6185XXI (industrial version).
For more information on MSL please see techbrief TB363.
4
FN6937.3
March 8, 2012
ISL6185
Pin Configurations
ISL6185
(10 LD DFN)
TOP VIEW
ISL6185
(8 LD SOIC/DFN)
TOP VIEW
GND
1
VIN
2
EN1/EN1
EN2/EN2
3
(GND)
EPAD
DFN Only
4
GND
1
VIN
2
VIN
3
8
FLT1
7
OUT1
OUT2
EN1/EN1
4
6
5
EN2/EN2
5
(GND)
EPAD
10
FLT1
9
OUT1
8
NC
7
OUT2
6
FLT2
FLT2
Pin Descriptions
PIN NUMBER
8 Ld
SOIC/DFN
10 Ld DFN
SYMBOL
1
1
GND
IC ground reference.
2
2, 3
VIN
Chip bias, Controlled Voltage Input, Undervoltage Lock Out (UVLO). VIN provides chip bias voltage. At
VIN < 1.7V chip functionality is disabled, FLT is active and floating, and OUT is held low. Range 0V to
5.5V.
3,
4
4,
5
EN1, EN1/
EN2, EN2
Enable/Disable inputs, Active high (EN) and active low (EN) options enable the power switch. These
inputs have internal 1MΩ pull-off resistors. Range 0V to VIN.
5,
8
6,
10
FLT2
FLT1
Overcurrent Fault Indicator. FLT floats and is disabled until VIN >VUVLO. This output is pulled low after
the current limit time-out period has expired. Fault is not signaled due to over-temperature shut down.
Range 0V to VIN.
6,
7
7,
9
OUT2,
OUT1
Controlled Supply Output. Upon an OC condition, IOUT is current limited. Current limit response time is
within 200µs. This output remains in current limit for a nominal 12ms before being turned off either for
the latch or auto retry versions. Range 0V to VIN.
-
8
NC
PD
(DFN only)
PD
EPAD
5
DESCRIPTION
This pin is not electrically connected internally.
Thermal Dissipation Exposed PAD Range: Connect to GND.
FN6937.3
March 8, 2012
ISL6185
Absolute Maximum Ratings
Thermal Information
Supply Voltage (VIN to GND, Note 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5V
EN, FAULT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VIN
OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to VIN 0.3V
Output Current . . . . . . . . . . . Short Circuit Protected Current Limit of 2.5A
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . . . 3kV
Machine Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . . . . . 300V
Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA
Thermal Resistance (Typical, Note 4)
θJA (°C/W) θJC (°C/W)
8 Lead SOIC Package (Note 4) . . . . . . . . . .
120
N/A
8 Lead 3x3 DFN Package (Notes 5, 6) . . .
48
6
10 Lead 3x3 DFN Package (Notes 5, 6) . .
53
6
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Commercial Temperature Range . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial Temperature Range . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . . . . . . . . . 2.3V to 5.5V
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
5. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
6. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
7. All voltages are relative to GND, unless otherwise specified.
Electrical Specifications
range, 0°C to +75°C or -40°C to +85°C.
SYMBOL
VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature
PARAMETER
TEST CONDITIONS
MIN
(Note 8)
TYP
MAX
(Note 8)
UNITS
-
71
87
mΩ
110
mΩ
105
mΩ
POWER SWITCH
rDS(ON)_50
ON-Resistance at 5.0V (Pulse Tested) VIN = 5V, IOUT = 0.1A, TA = TJ = +25°C
TA = TJ = +85°C
rDS(ON)_33
ON-Resistance at 3.3V (Pulse Tested) VIN = 3.3V, IOUT = 0.1A, TA = TJ = +25°C
rDS(ON)_25
On Resistance at 2.5V (Pulse Tested) VIN = 2.5V, IOUT = 0.1A, TA = TJ = +25°C
TA = TJ = +85°C
-
90
-
TA = TJ = +85°C
-
114
130
mΩ
127
mΩ
150
mΩ
VOUT_DIS
Disabled Output Voltage
VIN = 5V, Switch Disabled, 50µA Load
-
50
70
mV
ROUT_PU
Output Pull-Down Resistor
VIN = 5V, Switch Disabled
8
9.6
12
kΩ
tR
VOUT Rise Time
RL = 10Ω, CL = 10µF, 10% to 90%
-
100
-
µs
tF
Slow VOUT Turn-off Fall Time
RL = 10Ω, CL = 10µF, 90% to 10%
-
200
-
µs
tF_fast
Fast VOUT Turn-off Fall Time
RL = 1Ω, CL = 10µF, 80% to 20%
-
23
-
µs
ISL6185xA,B,E,F
-
0.6
A
ISL6185xC,D,G,H
-
1.1
A
ISL6185xI,J,K,L
-
1.5
A
ISL61853M,N,O,P (10 Ld DFN)
-
1.8
A
ISL6185xA,B,E,F
-
0.6
A
ISL6185xC,D,G,H
-
0.9
A
ISL61851I,J,K,L (SOIC)
-
1.3
A
ISL61852, ISL61853 (DFN)
-
1.5
A
CURRENT CONTROL
IOUT_CONT_5
IOUT_CONT_5
IOUT_CONT_5
Maximum Continuous Current, VIN =
5V.
Guaranteed by Itrip minimum
specification.
IOUT_CONT_5
IOUT_CONT_3
IOUT_CONT_3
IOUT_CONT_3
Maximum Continuous Current, VIN =
3.3V.
Guaranteed by Itrip minimum
specification.
IOUT_CONT_3
6
FN6937.3
March 8, 2012
ISL6185
Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature
range, 0°C to +75°C or -40°C to +85°C. (Continued)
MIN
(Note 8)
TYP
MAX
(Note 8)
UNITS
ISL6185xA,B,E,F
-
0.6
-
A
ISL61851C,D,G,H,I,J,K,L (SOIC)
-
0.9
-
A
IOUT_CONT_2
ISL61852, ISL61853 C,D,G,H (DFN)
-
1
-
A
IOUT_CONT_2
ISL61853I,J,K,L (10 Ld DFN)
-
1
-
A
SYMBOL
PARAMETER
IOUT_CONT_2
Maximum Continuous Current, VIN =
2.5V
IOUT_CONT_2
TEST CONDITIONS
-
1
-
A
ISL6185xA,B,E,F
ISL61853M,N,O,P (10 Ld DFN)
0.70
1.02
1.52
A
ITRIP_5
ISL6185xC,D,G,H
1.15
1.45
1.95
A
ITRIP_5
ISL6185xI,J,K,L
1.55
1.82
2.25
A
ITRIP_5
ISL61853M.N,O,P
1.85
1.99
2.45
A
IOUT_CONT_2
ITRIP_5
Trip Current, VIN = 5V
ISL6185xA,B,E,F
0.65
0.86
1.20
A
ITRIP_3
ISL6185xC,D,G,H
0.95
1.25
1.60
A
ITRIP_3
ISL6185xI,J,K,L
1.35
1.60
1.85
A
ITRIP_3
ISL61853M.N,O,P
1.55
1.89
2.25
A
ISL6185xA,B,E,F
-
0.65
-
A
ITRIP_2
ISL6185xC,D,G,H
-
1
-
A
ITRIP_2
ISL6185xI,J,K,L
-
1.2
-
A
ITRIP_2
ISL61853M.N,O,P
-
1.6
-
A
ISL6185xA,B,E,F, VIN - VOUT = 1V
0.50
0.65
0.78
A
ILIM_5
ISL6185xC,D,G,H, VIN - VOUT = 1V
0.98
1.14
1.28
A
ILIM_5
ISL6185xI,J,K,L, VIN - VOUT = 1V
1.30
1.55
1.72
A
ITRIP_3
ITRIP_2
ILIM_5
Trip Current, VIN = 3.3V
Trip Current, VIN = 2.5V
Current Limit, VIN = 5V
ISL61853M,N,O,P, VIN - VOUT = 1V
1.52
1.83
2.20
A
ISL6185xA,B,E,F, VIN - VOUT = 1V
0.45
0.63
0.75
A
ILIM_3
ISL6185xC,D,G,H, VIN - VOUT = 1V
0.90
1.10
1.26
A
ILIM_3
ISL6185xI,J,K,L, VIN - VOUT = 1V
1.25
1.50
1.68
A
ILIM_3
ISL61853M,N,O,P, VIN - VOUT = 1V
1.48
1.78
2.05
A
ILIM_5
ILIM_3
Current Limit, VIN = 3.3V
ISL6185xA,B,E,F, VIN - VOUT = 1V
0.47
0.61
0.74
A
ILIM_2
ISL6185xC,D,G,H, VIN - VOUT = 1V
0.90
1.05
1.17
A
ILIM_2
ISL6185xI,J,K,L, VIN - VOUT = 1V
1.15
1.37
1.58
A
ILIM_2
ISL61853M,N,O,P, VIN - VOUT = 1V
1.3
1.63
1.90
A
ISL6185xA,B,E,F, VOUT = 0V
0.60
0.80
1.00
A
ILIM_2
Isc_5
Current Limit, VIN = 2.5V
Short Circuit Current, VIN = 5V
Isc_5
ISL6185xC,D,G,H, VOUT = 0V
1.00
1.27
1.55
A
Isc_5
ISL6185xI,J,K,L, VOUT = 0V
1.15
1.61
1.85
A
Isc_5
ISL61853M,N,O,P, VOUT = 0V
1.20
1.70
2.5
A
ISL6185XA,B,E,F, VOUT = 0V
0.35
0.48
0.60
A
Isc_3
ISL6185XC,D,G,H, VOUT = 0V
0.65
0.80
0.95
A
Isc_3
ISL6185xI,J,K,L, VOUT = 0V
0.70
1.06
1.25
A
Isc_3
ISL61853M,N,O,P, VOUT = 0V
0.90
1.24
1.50
A
Isc_3
Short Circuit Current, VIN = 3.3V
7
FN6937.3
March 8, 2012
ISL6185
Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature
range, 0°C to +75°C or -40°C to +85°C. (Continued)
MIN
(Note 8)
TYP
ISL6185xA,B,E,F, VOUT = 0V
-
0.61
Isc_2
ISL6185xC,D,G,H, VOUT = 0V
-
1.06
-
A
Isc_2
ISL6185xI,J,K,L, VOUT = 0V
-
1.30
-
A
Isc_2
ISL61853M,N,O,P, VOUT = 0V
-
1.39
-
A
SYMBOL
Isc_2
PARAMETER
Short Circuit Current, VIN = 2.5V
TEST CONDITIONS
MAX
(Note 8)
UNITS
A
Isc_5.5
Short Circuit Current, VIN = 5.5V
All ISL6185X Variants
-
-
2.5
A
tsettIlim
OC to Limit Settling Time
VIN/RL = 2ILIM, CL = 10µF to within 10% of ILIM
-
200
-
µs
Severe OC to Limit Settling Time
VIN/RL = 4ILIM, CL = 10µF to within 10% of ILIM
-
30
-
µs
tCL
Current Limit Duration
IOUT = ILIM
9.2
12
15
ms
tRTY
Automatic Retry Period
0.80
1
1.35
s
-
-
0.4
V
-
5
-
µA
tsettIlim_sev
I/O PARAMETERS
Vfault_lo
Ifault
Fault Output Voltage
Fault IOUT = 10mA
Fault Leakage
EN / EN Rising Threshold
VIN = 5V
1.5
1.8
2
V
EN / EN Rising Threshold Hysteresis
VIN = 5V
80
140
175
mV
EN / EN Rising Threshold
VIN = 3.3V
1.0
1.3
1.6
V
EN / EN Rising Threshold Hysteresis
VIN = 3.3V
58
80
120
mV
EN / EN Rising Threshold
VIN = 2.5V
0.95
1.1
1.3
V
EN / EN Rising Threshold Hysteresis
VIN = 2.5V
30
70
110
mV
Ren_h
ENABLE Pull-Down Resistor
Enable asserted high options
0.6
1
1.55
MΩ
Ren_l
ENABLE Pull-Up Resistor
Enable asserted low options
0.6
1
1.55
MΩ
Venr_5
Hys_Venr_5
Venr_3
Hys_Venr_3
Venr_2
Hys_Venr_2
tON
Enable to Output Turn-on Time
RL = 10Ω, CL = 10µF, Enable 50% to Output 90%
-
0.1
-
ms
tOFF
Enable to Output Turn-off Time
RL = 10Ω, CL = 10µF, Enable 50% to Output 10%
-
0.25
-
ms
50
75
µA
BIAS PARAMETERS
IVDD
Enabled VIN Current
Switches Closed, OUTPUT = OPEN
IVDD
Disabled VIN Current
Switches Open, OUTPUT = OPEN
-
2
5
µA
VUVLO
Rising POR Threshold
VIN Rising to functional operation
1.7
2.1
2.3
V
Reverse Blocking Leakage Current
VIN = 0V, VOUT = 5V
2
µA
Temp_dis
Over-Temperature Disable
-
150
-
°C
Temp_hys
Over-Temperature Hysteresis
-
20
-
°C
IVR
-
NOTE:
8. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
8
FN6937.3
March 8, 2012
ISL6185
Introduction
Functional Description
The ISL6185 is a dual channel fully independent overcurrent (OC)
fault protection IC for the +2.5V to +5V environment. Each
ISL6185 incorporates in a single package two 85mΩ P-channel
MOSFET power switches for power control. Independent enabling
inputs and fault reporting outputs compatible with 2.5V to 5V
logic allow for external control and reporting. This device features
integrated power switches with current monitoring, accurate
current limiting, reverse bias protection and current limited
timed delay to turn-off for system reliability. See Figures 13
through 28 for typical operational waveforms including both
under-current and over-current situations.
Power On Preset (POR)
The ISL6185 offers current sense and limiting, with VIN = 5V
guaranteed continuous current product variants of 0.6A, 1.1A, 1.5A
and 1.8A, making these devices well suited for a myriad of USB and
other low power (9W max) port power management applications
and configurations.
Upon enable, the switch passes a constant current to the load.
The voltage on the VOUT pin ramps up according the equation,
ILIM/COUT (V/s). Resistive or active load slows the VOUT ramp-up
toward the top of its curve.
The ISL6185 also provides thermally insensitive timed OC turn-off
and fault notification. This isolates and protects the voltage bus in
the event of a peripheral OC event or short circuit event,
independent of the adjoining switch’s electrical or the ambient
thermal condition.
The ISL6185 undervoltage lockout feature prevents turn-on of
the outputs unless the correct ENABLE state and VIN > VUVLO
are present. During initial turn-on, the ISL6185 prevents fault
reporting by blanking the fault signal.
During operation, once an OC condition is detected, the output
is current limited for tCL to allow transient OC conditions to
pass. If still in current limit after the current limit period has
elapsed, the output is turned off, and the fault is reported by
pulling the corresponding FAULT output low. On the latch-off
options, after turn-off, both the output and the FAULT signal are
latched low until reset by the enable signal being de-asserted or
until a POR occurs. At this time, the FAULT signal clears, and
the switch is ready to be turned back on. On the auto restart
options, the ISL6185 attempts to periodically turn on the
output, as long as the enable is asserted.
When disabled, the ISL6185 has a low quiescent supply current
and an output-to-input reverse current flow blocking capability.
The ISL6185 family is provided with enable polarity options and
an industry-standard 8 lead SOIC pinout, along with two versions
in the 70% smaller 3x3 DFN. The 8 Ld DFN package offers the
same performance as the 8 Ld SOIC, whereas the 10 Ld DFN
offers higher current capability in the smallest possible package
because of lower package electrical and thermal resistance.
9
The ISL6185 POR feature inhibits device functionality when
VIN < VUVLO.
Reverse Polarity Protection
In any event in which the power switch is disabled and
VOUT > VIN, there will be no output-to-input current flow, nor will
the output voltage appear on the input.
Soft-Start
Fault Blanking On Start-Up
During initial turn-on, the ISL6185 prevents nuisance faults from
being reported to the system controller by blanking the fault
signal until the internal FET is fully enhanced.
Current Trip and Limiting Levels
The ISL6185 provides integrated current sensing in the MOSFET
that allows for rapid control of OC events. Once an OC condition is
detected, the ISL6185 goes into its current limiting (CL) control
mode. The ISL6185 is variant specified to allow a continuous
current (ICONT) operation of 0.6A, 1.1A, 1.5A or 1.8A. As the
current increases past its continuous current rating, it will reach
a level that causes the device to enter its current limit mode; that
is, the current trip level. The current trip level is in all cases
adequately above the ICONT rating so as not to cause unintended
false faults. The current limit is specified at VOUT = VIN - 1V to test
a known representative condition and is featured at a nominal
value slightly higher than the continuous current rating. The
speed of this current limiting control is inversely related to the
magnitude of the OC fault. Thus, a hard overcurrent is more
quickly pulled to its limiting value than a marginal OC condition.
Over-Temperature Shutdown
Although the ISL6185 has an over-temperature shutdown and
lockout feature, because of the 12ms timed shutdown, the
thermal shutdown is likely to be invoked only in extremely high
ambient temperatures.
The over-temperature protection invokes and disables the switch
turn-on operation once the die temperature is ~+140°C. It turns
off an already on switch at ~+150°C and releases the part to
operation once the die temperature falls to ~+120°C.
FN6937.3
March 8, 2012
ISL6185
Turn-off Time Delay
Latch-off Restart/Auto-Restart Start
During operation, once an OC condition is detected, the output
is current limited for ~12ms to allow transient OC conditions to
pass. If still in current limit and after the current limit period
has elapsed, the output is turned off, and the fault is reported
by pulling the corresponding FAULT low. The internal 12ms timer
starts upon current limiting and is independent of ambient or IC
thermal conditions, thus providing more consistent operation
over the entire temperature range.
After turn-off, with the latch-off options, both the output and the
FAULT signal are latched low until they are reset by the enable
signal being de-asserted. At this time, the FAULT signal clears,
and the IC is ready for enable to assert. On the auto restart
options, the ISL6185 attempts to periodically turn-on the
output at approximately 1s intervals, as long as the enable is
asserted. If the OC condition remains indefinitely, the fault
indication and the restart attempts also continue until the
thermal protection feature is invoked, thus increasing the
restart period.
Active Output Pull-down
Another ISL6185 feature is the 10kΩ active pull-down on the
outputs to <60mV above GND when the device is disabled, thus
ensuring discharge of the load.
Typical Performance Curves
150
1.3
rDS(ON) @ 0.5A (mΩ)
130
VIN = 2.5V
120
110
100
VIN = 3.3V
90
80
VIN = 5V
70
NORMALIZED rDS(ON)
140
1.1
1.0
0.9
0.8
60
50
-40
-25
0
25
45
75
TEMPERATURE (°C)
85
0.7
115
FIGURE 3. SWITCH ON-RESISTANCE AT 0.5A
1.5
1.0
0.9
3.3V ITRIP
0.8
0.7
0.6
0.5
0.4
-25
0
25
45
75
TEMPERATURE (°C)
85
115
1.6
5V ITRIP
OUTPUT CURRENT (A)
1.1
-40
FIGURE 4. NORMALIZED SWITCH RESISTANCE
1.2
OUTPUT CURRENT (A)
1.2
5V ISC
5V ILIM
3.3V ILIM
-25
0
25
45
75
TEMPERATURE (°C)
85
115
FIGURE 5. 0.6A CONTINUOUS CURRENT CHARACTERISTICS
10
1.3
1.2
1.1
5V ITRIP
5V ISC
3.3V ITRIP
5V ILIM
1.0 3.3V ILIM
0.9
0.8
3.3V ISC
0.7
3.3V ISC
-40
1.4
0.6
-40
-25
0
25
45
75
TEMPERATURE (°C)
85
115
FIGURE 6. 1.1A CONTINUOUS CURRENT CHARACTERISTICS
FN6937.3
March 8, 2012
ISL6185
(Continued)
2.0
2.2
1.8 5V ITRIP
2.0
1.6
1.4
3.3V ITRIP
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
Typical Performance Curves
5V ISC
5V ILIM
3.3V ILIM
1.2
3.3V ISC
1.0
0.8
-40
-25
0
25
45
75
85
3.3V ITRIP
1.8
1.6
3.3V ILIM
3.3V ISC
1.2
-40
-25
TEMPERATURE (°C)
FIGURE 7. 1.5A CONTINUOUS CURRENT CHARACTERISTICS
0.75
TYPICAL
0.60
-3 SIGMA
0.55
0.50
115
+3 SIGMA
1.15
TYPICAL
1.10
-3 SIGMA
1.05
-40
-25
0
25
45
75
TEMPERATURE (°C)
85
1.00
115
FIGURE 9. LIMITING CURRENT ±3 SIGMA, VIN = 5V
1.65
2.00
1.50
-3 SIGMA
1.45
1.40
ILIMIT ± 3 SIGMA
TYPICAL
-25
0
25
45
75
TEMPERATURE (°C)
1.8A CONTINUOUS IOUT VERSION
1.95
+3 SIGMA
1.55
-40
85
115
FIGURE 10. LIMITING CURRENT ±3 SIGMA, VIN = 5V
1.5A CONTINUOUS IOUT VERSION
1.60
ILIMIT ± 3 SIGMA
85
1.1A CONTINUOUS IOUT VERSION
1.20
ILIMIT ± 3 SIGMA
ILIMIT ± 3 SIGMA
1.25
+3 SIGMA
0.65
0
25
45
75
TEMPERATURE (°C)
FIGURE 8. 1.8A CONTINUOUS CURRENT CHARACTERISTICS
0.6A CONTINUOUS IOUT VERSION
0.70
5V ISC
5V ILIM
1.4
1.0
115
5V ITRIP
+3 SIGMA
1.90
1.85
TYPICAL
1.80
-3 SIGMA
1.75
1.70
1.65
1.35
1.60
-40
-25
0
25
45
75
85
115
TEMPERATURE (°C)
FIGURE 11. LIMITING CURRENT ±3 SIGMA, VIN = 5V
11
-40
-25
0
25
45
75
TEMPERATURE (°C)
85
115
FIGURE 12. LIMITING CURRENT ±3 SIGMA, VIN = 5V
FN6937.3
March 8, 2012
ISL6185
Typical Performance Curves
(Continued)
ENABLE
ENABLE
CL = 1µF
CL = 10µF
CL = 10µF
VOUT
1V/DIV
CL = 100µF
CL = 100µF
VOUT
1V/DIV
CL = 1µF
FIGURE 13. VOUT TURN-ON/RISE TIME vs C LOAD. VIN = 5V,
RL = 10Ω
FIGURE 14. VOUT TURN-OFF/FALL TIME
vs CLOAD. VIN = 5V, RL = 10Ω
0.6A ICONT VARIANT
FLT
CL = 10µF
VOUT
1V/DIV
VOUT
CL = 100µF
IIN
CL = 1µF
FIGURE 15. LATCH-OFF vs CLOAD
0.6A ICONT VARIANT
FIGURE 16. ILIM WAVEFORM
0.6A ICONT VARIANT
2A OC 27µs
6A/ms
0.6A/ms
1A OC 57µs
0.08A/ms
0.5A OC 200µs
0.72A CURRENT LIMIT
0.53A LOAD CURRENT
0.56A LOAD CURRENT
IIN 2A/DIV
FIGURE 17. OC RAMP RATE ILIM WAVEFORMS
12
0.66A CURRENT LIMIT
FIGURE 18. PEAK CURRENT SETTLING TIMES
FN6937.3
March 8, 2012
ISL6185
Typical Performance Curves
(Continued)
ENABLE
ENABLE
0.6A ICONT VARIANT
0.6A ICONT VARIANT
VOUT
FAULT
FAULT
IIN
LIMITED TO 0.64A
IIN
VOUT
FIGURE 20. TURN-ON INTO MOMENTARY OC
FIGURE 19. TURN-ON INTO A SHORT
1.1A ICONT VARIANT
FLT
VOUT
VOUT
FLT
IIN
IIN
FIGURE 21. ISL6185 RETRY FUNCTION
FIGURE 22. ILIM WAVEFORM
ENABLE
ENABLE
FAULT
FAULT
VOUT
VOUT
Iin
IIN
1.8A ICONT VARIANT
FIGURE 23. VIN = 2.5V TURN-ON INTO 2.2Ω
13
1.8A ICONT VARIANT
FIGURE 24. VIN = 5V TURN-ON INTO 2.7Ω
FN6937.3
March 8, 2012
ISL6185
Typical Performance Curves
(Continued)
CH1 and CH2 ON
(3.6A TOTAL IIN)
IIN
ENABLE
FAULT
VOUT
CH1 ON
(1.8A)
IIN
LIMITED TO 1.7A
ENABLE
FAULT
1.8A ICONT VARIANT
VOUT
FIGURE 26. TURN-ON 2ND OUTPUT TO FULL LOAD
FIGURE 25. TURN-ON INTO A SHORT
1.1A ICONT VARIANT
FLT
VOUT
VOUT
FLT
IIN
IIN
FIGURE 27. ISL6185 RETRY FUNCTION
FIGURE 28. ILIM WAVEFORM
FIGURE 28. PROPAGATION DELAY AND OUTPUT TRANSITION TIMES
Test Circuits
+
V
10k
10k
5V
VIN
OUT
ISL6185
OUTPUT
FLT
FLT
OUTPUT
10µF
EN
5V
VIN
ISL6185
EN
10
OUT
10µF
10
RL sized
for desired
OC level
RL
rDS(ON) = V/(VOUT/10W)
FIGURE 29A. rDS(ON)
FIGURE 29B. CURRENT LIMITING
FIGURE 29. DC TEST CIRCUIT
14
FN6937.3
March 8, 2012
ISL6185
Test Circuits (Continued)
VIN
EN
0.5VIN
0.5VIN
10k
0V
tON
FLT
5V
VIN
OUTPUT
OUT
10µF
ISL6185
0-VIN
OUTPUT
EN
tOFF
VIN
90%
10%
GND
10
90%
OUTPUT
10%
tR
FIGURE 30. TRANSIENT TEST CIRCUIT
VIN
90%
10%
-GND
tF
FIGURE 31. TRANSIENT WAVEFORM MEASUREMENT POINTS
ISL6185xEVAL1Z Schematic and Photo
R1
10k
AGND
C1
V+
2.2µF
A
AGND
V+
EN1
EN2
A
A
U1
ISL6185
R3
FLT1
OUT1
OUT2
FLT2
10
C2
10µF
A
R4
OUT2
10
C3
R2
FLT1
OUT1
10µF
A
FLT2
10k
NOTE: EXPOSED PAD on DFN packages only
FIGURE 32A. ISL6185xEVAL SCHEMATIC
FIGURE 32B. ISL61851EVAL1Z BOARD PHOTO
FIGURE 32. ISL6185xEVAL1Z SCHEMATIC and ISL61851EVAL1Z PHOTOGRAPH
15
FN6937.3
March 8, 2012
ISL6185
Application Information
Application Considerations
Using the ISL6185xEVAL1Z Platform
General and Biasing Information
The application considerations for the ISL6185 family are widely
accepted best industry practices. Good decoupling practices on
the VIN pin must be followed: placement close to the IC, with at
least 2.2µF recommended. It is recommended to reduce the
input and output inductance to the ISL6185 with good PCB
layout practices.
There are three evaluation platforms for the ISL6185 family.
There is one platform for each package style, each with a
different continuous output current level and a mix of enable
polarity and output retry or latch options. See page 4, at the end
of the “Ordering Information” table, for information on the
standard available evaluation board options. Figure 32A shows
the common schematic for all three evaluation boards. See “Pin
Configurations” on page 5 for details and differences.
The evaluation platform is biased and monitored through
numerous labeled test points. See Table 1 for test point
assignments and descriptions.
TABLE 1. ISL61851EVAL1Z TEST POINT ASSIGNMENTS
TP NAME
DESCRIPTION
GND
Eval Board and IC Gnd
V+
Eval Board and IC Bias
EN1
Enable Switch 1
EN2
Enable Switch 2
FLT2
Switch 2 Fault
OUT2
Switch Out 2
OUT1
Switch Out 1
FLT1
Switch 1 Fault
When designing with the 1.5A and 1.8A versions in an
implementation in which the output may be unloaded (open)
while the ISL6185 is turned on, a minimum of 4.7µF of
capacitive output load is recommended to prevent high dv/dt
from unnecessarily activating the surge/ESD control circuit.
The ISL6185 provides several continuous current rated devices
specified at VIN = 5V; these are 0.6A, 1.1A, 1.5A and 1.8A
options that are capable over the entire temperature extreme. At
VIN = 3.3V, the current capability is degraded, and the ISL6185 is
specified at 0.6A, 1.1A, 1.3A and 1.5A, respectively. At
VIN = 2.5V, there are no minimum specifications, but a typical
value is provided for +25°C operation (see “Electrical
Specifications” on page 6). This degraded capability is due to the
higher rDS(ON) of the FET switch at the lower bias voltage.
The enhanced thermal characteristics and increased number of
bond wires allow the 10 Ld DFN to have a higher current
capability than either the 8 Ld SOIC or the DFN.
TABLE 2. ISL6185XEVAL1Z BOARD COMPONENT LISTING
COMPONENT
DESIGNATOR
U1
Upon proper bias of the evaluation platform and correct enabling
of the IC, the ISL6185 will have a nominal VIN/10Ω load current
that is lower than the continuous current rating passing through
each enabled switch. See Figures 13 and 14 for typical ISL6185
turn-on and turn-off waveforms.
External current loading in excess of the trip current level for the
particular part being evaluated will result in the ISL6185 entering
the current limiting mode. Figure 16 illustrates the current
limiting mode for the ISL6185 product variants with 0.6A of
continuous load current rating. The scope shot shows current
limiting for ~12ms before it is turned off and the fault signal is
asserted.
COMPONENT
FUNCTION
COMPONENT DESCRIPTION
ISL6185
Intersil, ISL6185
R3 - R4
Output Load
Resistors
10Ω, 5%, 3W
R1 - R2
FLT Output Pull-up
Resistor
10kΩ, 0805
Decoupling
Capacitor
2.2µF, 0805
Load Capacitor
10µF 16V Electrolytic,
Radial Lead
C1
C2 - C3
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
16
FN6937.3
March 8, 2012
ISL6185
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make
sure you have the latest Rev.
DATE
REVISION
March 1, 2012
FN6937.3
CHANGE
In “Features” on page 1 changed from:
UL Recognized, File Number: E333469
(Applies to DFN Packages, SOIC Package to be Qualified Shortly)
to:
UL Recognized, File Number : E333469
In “Absolute Maximum Ratings” on page 6:
Changed from:
Output Current . . . . . . . . . Short Circuit Protected
to:
Output Current . . . . . . . . . .Short Circuit Protected Current Limit of 2.5A
Updated “Package Outline Drawing” on page 20. Changed Note 1 "1982" to "1994".
December 2, 2011
FN6937.2
Page 1: Added "UL Recognized, File Number: E333469 (Applies to DFN packages, SOIC pkg to be qualified
shortly)" to "Features"
Page 8: Added Isc_5.5, Short Circuit Current with max of 2.5A to “Electrical Specifications”
Page 19: Updated package outline drawing to most updated revision. Removed package outline and included
center to center distance between lands on recommended land pattern. Removed Note 4 "Dimension b applies
to the metallized terminal and is measured between 0.18mm and 0.30mm from the terminal tip." since it is
not applicable to this package. Renumbered notes accordingly.
June 14, 2011
FN6937.1
Page 2: “Ordering Information”: added part numbers of parts installed on evaluation boards to Description
column.
Page 7: “Electrical Specifications” table:
- For “Maximum Continuous Current, VIN = 2.5V,” changed “ISL61851C,D,G,H (SOIC)” to
“ISL61851C,D,G,H,I,J,K,L (SOIC)”
- For “Trip Current, VIN = 5V”, changed “ISL61853I,J,K,L” to “ISL6185xI,J,K,L”. For “ISL61853M.N,O,P” changed
MAX from “2.15” to “2.45”.
- For “Trip Current, VIN = 3.3V” and “Trip Current, VIN = 2.5V” changed “ISL61853I,J,K,L“ to “ISL6185xI,J,K,L“.
- For “Current Limit, VIN = 5V”, “Current Limit, VIN = 3.3V”, and “Current Limit, VIN = 2.5V”, changed
“ISL61853I,J,K,L, VIN - VOUT = 1V” to “ISL6185xI,J,K,L, VIN - VOUT = 1V”
- For “Short Circuit Current, VIN = 5V”, “Short Circuit Current, VIN = 3.3V” and “Short Circuit Current, VIN = 2.5V”
changed “ISL61853I,J,K,L, VOUT = 0V” to “ISL6185xI,J,K,L, VOUT = 0V”
Page 8: “Electrical Specifications” table: For the I/O Parameters Venr_5, Hys_Venr_5, Venr_3, Hys_Venr_3,
Venr_2, and Hys_Venr_2: changed "ENABLE Rising Threshold" and "ENABLE Rising Threshold Hysteresis" to "EN
/ EN Rising Threshold" and "EN / EN Rising Threshold Hysteresis," for clarity.
Page 8: Electrical Specifications table: Removed UVHYS, POR Hysteresis specification.
Page 20: Replaced Rev. 1 of M8.15 package outline drawing, dated 6/05, with Rev 2 (latest version), dated
11/10.
Applied current Intersil datasheet template to document.
October 22, 2010
FN6937.0
Initial release.
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products
address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks.
Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a
complete list of Intersil product families.
For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information pages
on intersil.com for ISL6185XXC (commercial version) and ISL6185XXI (industrial version).
To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff
FITs are available from our website at: http://rel.intersil.com/reports/sear
17
FN6937.3
March 8, 2012
ISL6185
Package Outline Drawing
L8.3x3J
8 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE
Rev 0 9/09
2X 1.950
3.00
B
0.15
8
5
3.00
(4X)
6X 0.65
A
1.64 +0.10/ - 0.15
6
PIN 1
INDEX AREA
4
8X 0.30
8X 0.400 ± 0.10
TOP VIEW
6
PIN #1 INDEX AREA
1
4
0.10 M C A B
2.38
+0.10/ - 0.15
BOTTOM VIEW
SEE DETAIL "X"
( 2.38 )
( 1.95)
0.10 C
Max 1.00
C
0.08 C
SIDE VIEW
( 8X 0.60)
(1.64)
( 2.80 )
PIN 1
C
0 . 2 REF
5
(6x 0.65)
0 . 00 MIN.
0 . 05 MAX.
( 8 X 0.30)
DETAIL "X"
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Dimension applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Tiebar shown (if present) is a non-functional feature.
6.
18
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
FN6937.3
March 8, 2012
ISL6185
Package Outline Drawing
L10.3x3
10 LEAD DUAL FLAT PACKAGE (DFN)
Rev 7, 10/11
3.00
5
PIN #1 INDEX AREA
A
B
1
5
PIN 1
INDEX AREA
(4X)
3.00
2.00
8x 0.50
2
10 x 0.23
0.10
1.60
TOP VIEW
10x 0.35
BOTTOM VIEW
(4X)
0.10 M C A B
0.415
0.200
0.23
0.35
(10 x 0.55)
SEE DETAIL "X"
(10x 0.23)
1.00
MAX
0.10 C
BASE PLANE
2.00
0.20
C
SEATING PLANE
0.08 C
SIDE VIEW
(8x 0.50)
C
0.20 REF
4
1.60
0.05
2.85 TYP
TYPICAL RECOMMENDED LAND PATTERN
DETAIL "X"
NOTES:
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Tiebar shown (if present) is a non-functional feature.
5.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
19
FN6937.3
March 8, 2012
ISL6185
Package Outline Drawing
M8.15
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
Rev 4, 1/12
DETAIL "A"
1.27 (0.050)
0.40 (0.016)
INDEX
6.20 (0.244)
5.80 (0.228)
AREA
0.50 (0.20)
x 45°
0.25 (0.01)
4.00 (0.157)
3.80 (0.150)
1
2
8°
0°
3
0.25 (0.010)
0.19 (0.008)
SIDE VIEW “B”
TOP VIEW
2.20 (0.087)
SEATING PLANE
5.00 (0.197)
4.80 (0.189)
1.75 (0.069)
1.35 (0.053)
1
8
2
7
0.60 (0.023)
1.27 (0.050)
3
6
4
5
-C-
1.27 (0.050)
0.51(0.020)
0.33(0.013)
SIDE VIEW “A
0.25(0.010)
0.10(0.004)
5.20(0.205)
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1. Dimensioning and tolerancing per ANSI Y14.5M-1994.
2. Package length does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
3. Package width does not include interlead flash or protrusions. Interlead
flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.
4. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
5. Terminal numbers are shown for reference only.
6. The lead width as measured 0.36mm (0.014 inch) or greater above the
seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch).
7. Controlling dimension: MILLIMETER. Converted inch dimensions are not
necessarily exact.
8. This outline conforms to JEDEC publication MS-012-AA ISSUE C.
20
FN6937.3
March 8, 2012