Maxim MAX4210 High-side power and current monitor Datasheet

19-3285; Rev 1; 5/05
KITS
ATION
EVALU ABLE
AVAIL
High-Side Power and
Current Monitors
The MAX4210/MAX4211 low-cost, low-power, high-side
power/current monitors provide an analog output voltage proportional to the power consumed by a load by
multiplying load current and source voltage. The
MAX4210/MAX4211 measure load current by using a
high-side current-sense amplifier, making them especially useful in battery-powered systems by not interfering with the ground path of the load.
The MAX4210 is a small, simple 6-pin power monitor
intended for limited board space applications. The
MAX4210A/B/C integrate an internal 25:1 resistor-divider
network to reduce component count. The MAX4210D/E/F
use an external resistor-divider network for greater design
flexibility.
The MAX4211 is a full-featured current and power monitor. The device combines a high-side current-sense
amplifier, 1.21V bandgap reference, and two comparators with open-drain outputs to make detector circuits
for overpower, overcurrent, and/or overvoltage conditions. The open-drain outputs can be connected to
potentials as high as 28V, suitable for driving high-side
switches for circuit-breaker applications.
Both the MAX4210/MAX4211 feature three different current-sense amplifier gain options: 16.67V/V, 25.00V/V, and
40.96V/V. The MAX4210 is available in 3mm x 3mm, 6-pin
TDFN and 8-pin µMAX® packages and the MAX4211 is
available in 4mm x 4mm, 16-pin thin QFN and 16-pin
TSSOP packages. Both parts are specified for the -40°C
to +85°C extended operating temperature range.
Features
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
Real-Time Current and Power Monitoring
±1.5% (max) Current-Sense Accuracy
±1.5% (max) Power-Sense Accuracy
Two Uncommitted Comparators (MAX4211)
1.21V Reference Output (MAX4211)
Three Current/Power Gain Options
100mV/150mV Current-Sense Full-Scale Voltage
+4V to +28V Input Source Voltage Range
+2.7V to +5.5V Power-Supply Voltage Range
Low Supply Current: 380µA (MAX4210)
220kHz Bandwidth
Small 6-Pin TDFN and 8-Pin µMAX Packages
(MAX4210)
Ordering Information
PART
TEMP RANGE
MAX4210AETT-T
-40°C to +85°C
MAX4210AEUA
-40°C to +85°C 8 µMAX
AHF
—
Ordering Information continued at end of data sheet.
Functional Diagrams
4V TO
28V
VSENSE
-
RSENSE
+
-
LOAD
RS+
Overpower Circuit Breakers
Smart Battery Packs/Chargers
6 TDFN-6-EP*
(3mm x 3mm)
TOP
MARK
*EP = Exposed paddle.
+
Applications
PIN-PACKAGE
RS-
VCC
2.7V TO
5.5V
+
-
Smart Peripheral Control
IOUT
25:1
Short-Circuit Protection
POUT
Power-Supply Displays
1.21V
REFERENCE
Measurement Instrumentation
Baseband Analog Multipliers
INHIBIT
VGA Circuits
COUT1
Power-Level Detectors
LE
REF
CIN1+
CIN1-
CIN2+
COUT2
µMAX is a registered trademark of Maxim Integrated Products, Inc.
Pin Configurations and Selector Guide appear at end of data
sheet.
CIN2MAX4211A
MAX4211B
MAX4211C
GND
Functional Diagrams continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX4210/MAX4211
General Description
MAX4210/MAX4211
High-Side Power and
Current Monitors
ABSOLUTE MAXIMUM RATINGS
VCC, IN, CIN1, CIN2 to GND ....................................-0.3V to +6V
RS+, RS-, INHIBIT, LE, COUT1, COUT2 to GND ...-0.3V to +30V
IOUT, POUT, REF to GND ..........................-0.3V to (VCC + 0.3V)
Differential Input Voltage (VRS+ - VRS-) .................................±5V
Maximum Current into Any Pin..........................................±10mA
Output Short-Circuit Duration to VCC or GND ........................10s
Continuous Power Dissipation (TA = +70°C)
6-Pin TDFN (derate 24.4mW/°C above +70°C) ..........1951mW
8-Pin µMAX (derate 4.5mW/°C above +70°C) .............362mW
16-Pin TSSOP (derate 9.4mW/°C above +70°C) ..........754mW
16-Pin Thin QFN (derate 25mW/°C above +70°C) .....2000mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = 5.0V, VRS+ = 25V, VSENSE = 5mV, VIN = 1.0V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
GND, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
Operating Voltage Range
(Note 2)
Common-Mode Input Range
(Note 3)
Supply Current
SYMBOL
CONDITIONS
VCC
VCMR
ICC
Measured at RS+
TA = +25°C,
VCC = +5.5V
IN Input Bias Current
Leakage Current
VSENSE Full-Scale Voltage
(Note 4)
IN Full-Scale Voltage
(Note 4)
IN Input Voltage Range
(Note 5)
Minimum IOUT/POUT Voltage
Maximum IOUT/POUT Voltage
(Note 6)
2
2.7
5.5
V
4
28
V
MAX4210
380
MAX4211
670
25
8
VSENSE = 0mV
MAX421_D/E/F
3
-0.1
8
-1
µA
VCC = 0V
0.1
1
µA
MAX421_A/B/D/E
150
MAX421_C/F
100
1
VIN
MAX421_D/E/F, VSENSE = 10mV to
100mV
0.16
MAX421_A/B/C, VSENSE = 10mV to
100mV
25
MAX421_A/B/C, VSENSE = 10mV to
100mV
4
VOUT_MAX
µA
3
MAX421_D/E/F, VSENSE = 10mV to
100mV
VOUT_MIN
960
670
1100
VIN_FS
VRS+
570
14
IRSIIN
VRS+ Full-Scale Voltage
(Note 4)
VRS+ Input Voltage Range
(Note 5)
UNITS
MAX421_A/B/C
VSENSE = 0mV
VSENSE_FS
MAX
MAX421_D/E/F
IRS+
IRS+, IRS-
TYP
MAX4210
MAX4211
VCC = +5.5V
Input Bias Current
MIN
VSENSE =
0V, VRS+ =
25V
VSENSE =
300mV,
VRS+ = 25V
µA
mV
V
1.10
V
V
28
Current into IOUT = 10µA
1.5
Current into IOUT = 100µA
2.5
Current into POUT = 10µA
1.5
Current into POUT = 100µA
2.5
80
mV
80
Current out of
IOUT = 500µA
VCC 0.25
Current out of
POUT = 500µA
VCC 0.25
_______________________________________________________________________________________
V
V
High-Side Power and
Current Monitors
(VCC = 5.0V, VRS+ = 25V, VSENSE = 5mV, VIN = 1.0V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
GND, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
Current-Sense Amplifier Gain
SYMBOL
VIOUT/
VSENSE
VPOUT/
(VSENSE x
VRS+)
Power-Sense Amplifier Gain
VPOUT/
(VSENSE x VIN)
CONDITIONS
MIN
TYP
MAX4211A/D
16.67
MAX4211B/E
25.00
MAX4211C/F
40.96
MAX421_A
0.667
MAX421_B
1.00
MAX421_C
1.64
MAX421_D
16.67
MAX421_E
25.00
MAX421_F
MAX
UNITS
V/V
1/V
40.96
IOUT Common-Mode Rejection
CMRI
MAX4211, VRS+ = 4V to 28V
60
80
dB
POUT Common-Mode Rejection
CMRP
MAX421_D/E/F, VRS+ = 4V to 28V
60
80
dB
IOUT Power-Supply Rejection
PSRI
VCC = 2.7V to 5.5V
52
80
dB
POUT Power-Supply Rejection
PSRP
VCC = 2.7V to 5.5V
52
70
dB
Output Resistance for POUT,
IOUT, REF
ROUT
0.5
Ω
VSENSE = 100mV, VSENSE AC source
220
kHz
BWPOUT/SENSE VSENSE = 100mV, VSENSE AC source
220
IOUT -3dB Bandwidth
POUT -3dB Bandwidth
Capacitive-Load Stability
(POUT, IOUT, REF)
Current Output (IOUT) Settling
Time to 1% of Final Value
BWIOUT/SENSE
BWPOUT/VIN
VSENSE = 100mV, VIN AC source,
MAX421_D/E/F
500
BWPOUT/RS+
VSENSE = 100mV, VRS+ AC source,
MAX421_A/B/C
250
No sustained oscillations
450
CLOAD
MAX4211
MAX421_A/B/C
Power Output (POUT) Settling
Time to 1% of Final Value
MAX421_D/E/F
VSENSE = 10mV to 100mV
15
VSENSE = 100mV to 10mV
15
VSENSE = 10mV to 100mV
10
VSENSE = 100mV to 10mV
10
VRS+ = 4V to 25V,
VSENSE = 100mV
15
VRS+ = 25V to 4V,
VSENSE = 100mV
15
VSENSE = 10mV to 100mV
10
VSENSE = 100mV to 10mV
10
VIN = 160mV to 1V,
VSENSE = 100mV
10
VIN = 1V to 160mV,
VSENSE = 100mV
10
kHz
pF
µs
µs
_______________________________________________________________________________________
3
MAX4210/MAX4211
ELECTRICAL CHARACTERISTICS (continued)
MAX4210/MAX4211
High-Side Power and
Current Monitors
ELECTRICAL CHARACTERISTICS (continued)
(VCC = 5.0V, VRS+ = 25V, VSENSE = 5mV, VIN = 1.0V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
GND, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Power-Up Time to 1% of
Current Output Final Value
VSENSE = 100mV, CLOAD = 10pF,
MAX4211
100
µs
Power-Up Time to 1% of Power
Output Final Value
VSENSE = 100mV, CLOAD = 10pF
100
µs
CLOAD = 10pF, VSENSE = -100mV to
+100mV
35
CLOAD = 10pF, VSENSE = 1.5V to 100mV
35
VCC = 5V, VRS+ = 10V, CLOAD = 10pF,
VSENSE = -100mV to +100mV
25
VCC = 5V, VRS+ = 10V, CLOAD = 10pF,
VSENSE = 1.5V to 100mV
25
Saturation Recovery Time for
Current Out (Note 7)
Saturation Recovery Time for
Power Out (Note 7)
Reference Voltage
VREF
Comparator Input Offset
µs
µs
IREF = 0 to 100µA, TA = +25°C
1.20
IREF = 0 to 100µA, TA = -40°C to +85°C
1.19
1.21
±0.5
Common-mode voltage = REF
Comparator Hysteresis
1.22
1.23
±5
V
mV
5
mV
Comparator Common-Mode
Low
Functional test
0.1
V
Comparator Common-Mode
High
Functional test
VCC 1.15
V
-2
nA
Comparator Input Bias Current
IBIAS
Comparator Output Low
Voltage
VOL
Comparator Output-High
Leakage Current (Note 8)
ISINK = 1mA
0.2
VPULLUP = 28V
LE Logic Input-High Voltage
Threshold
VIH
LE Logic Input-Low Voltage
Threshold
VIL
0.68
INHIBIT Logic Input-High
Voltage Threshold
1.3
1
µA
V
1
0.33 x
VCC
V
2.20
µA
V
INHIBIT Logic Input-Low
Voltage Threshold
0.5
INHIBIT Logic Input Hysteresis
4
V
0.67 x
VCC
LE Logic Input Internal
Pulldown Current
INHIBIT Logic Input Internal
Pulldown Current
0.6
0.6
0.68
1
_______________________________________________________________________________________
V
V
2.20
µA
High-Side Power and
Current Monitors
(VCC = 5.0V, VRS+ = 25V, VSENSE = 5mV, VIN = 1.0V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
GND, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
Comparator Propagation
Delay
SYMBOL
tPD+, tPD-
CONDITIONS
MIN
CLOAD = 10pF, RLOAD = 10kΩ pullup to
VCC, 5mV overdrive
Minimum INHIBIT Pulse
Width
Minimum LE Pulse Width
Comparator Power-Up
Blanking Time From VCC
LATCH Setup Time
tON
VCC from 0 to (2.7V to 5.5V)
tSETUP
TYP
MAX
UNITS
4
µs
1
µs
1
µs
300
µs
3
µs
MAX4210A/MAX4211A (power gain = 0.667)
POUT Gain Accuracy
(Note 9)
∆VPOUT/
∆VSENSE
VSENSE = 10mV to
100mV, VRS+ = 25V
TA = +25°C
∆VPOUT/
∆VRS+
VSENSE = 100mV,
VRS+ = 5V to 25V
TA = +25°C
VSENSE = 5mV to
100mV, VRS+ = 5V to
25V
TA = +25°C
VSENSE = 150mV,
VRS+ ≥ 15V
TA = +25°C
∆VPOUT_MAX/
FSO
Total POUT Output Error
(Note 10)
∆VPOUT_MAX/
VPOUT
±1.5
±3.0
TA = TMIN to TMAX
±0.5
±1.5
%
±3.0
TA = TMIN to TMAX
±0.15
±1.5
% FSO*
±3.0
TA = TMIN to TMAX
±0.2
VSENSE = 100mV, VRS+ ≥ 4V
±2.5
VSENSE = 100mV, VRS+ ≥ 9V
±1.2
VSENSE = 50mV, VRS+ ≥ 6V
±1.8
VSENSE = 25mV, VRS+ ≥ 15V
±1.8
TA = +25°C
∆VPOUT/
∆VSENSE
VSENSE = 10mV to
100mV, VRS+ = 25V
TA = +25°C
∆VPOUT/
∆VRS+
VSENSE = 100mV,
VRS+ = 5V to 25V
TA = +25°C
±1.5
±3.0
TA = TMIN to TMAX
VSENSE = 0V,
VRS+ = 25V
POUT Output Offset Voltage
(Note 11)
±0.5
1.5
TA = TMIN to TMAX
%
5
15
mV
MAX4210B/MAX4211B (power gain = 1.00)
POUT Gain Accuracy
(Note 9)
±0.5
±3.0
TA = TMIN to TMAX
TA = TMIN to TMAX
±1.5
±0.5
±1.5
%
±3.0
*FSO refers to full-scale output under the conditions: VSENSE = 100mV, VRS+ = +25V, or VIN = 1V.
_______________________________________________________________________________________
5
MAX4210/MAX4211
ELECTRICAL CHARACTERISTICS (continued)
MAX4210/MAX4211
High-Side Power and
Current Monitors
ELECTRICAL CHARACTERISTICS (continued)
(VCC = 5.0V, VRS+ = 25V, VSENSE = 5mV, VIN = 1.0V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
GND, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
Total POUT Output Error
(Note 10)
SYMBOL
CONDITIONS
∆VPOUT_MAX/
FSO
VSENSE = 5mV to
TA = +25°C
100mV, VRS+ = 5V to
TA = TMIN to TMAX
25V
VSENSE = 150mV,
VRS+ > 15V
∆VPOUT_MAX/
VPOUT
POUT Output Offset Voltage
(Note 11)
MIN
TA = +25°C
TYP
MAX
±0.15
±1.5
±0.2
±1.5
±3.0
TA = TMIN to TMAX
±2.5
VSENSE = 100mV, VRS+ > 9V
±1.2
VSENSE = 50mV, VRS+ > 6V
±1.8
VSENSE = 25mV, VRS+ > 15V
±1.8
TA = +25°C
% FSO*
±3.0
VSENSE = 100mV, VRS+ > 4V
VSENSE = 0V,
VRS+ = 25V
UNITS
2
TA = TMIN to TMAX
%
6.5
20
mV
MAX4210C/MAX4211C (power gain = 1.64)
POUT Gain Accuracy
(Note 9)
Total POUT Output Error
(Note 10)
∆VPOUT/
∆VSENSE
VSENSE = 10mV to
100mV, VRS+ = 25V
TA = +25°C
∆VPOUT/
∆VRS+
VSENSE = 100mV,
VRS+ = 5V to 25V
TA = +25°C
∆VPOUT_MAX/
FSO
VSENSE = 5mV to
100mV, VRS+ = 5V
to 25V
TA = +25°C
∆VPOUT_MAX/
VPOUT
±0.5
±0.15
VSENSE = 100mV, VRS+ ≥ 4V
±2.5
VSENSE = 100mV, VRS+ ≥ 9V
±1.2
VSENSE = 50mV, VRS+ ≥ 6V
±1.8
VSENSE = 25mV, VRS+ ≥ 15V
±1.8
VSENSE = 10mV to
100mV, VIN = 1V
TA = +25°C
∆VPOUT/
∆VIN
VSENSE = 100mV,
VIN = 0.2V to 1V
TA = +25°C
%
±1.5
±3.0
TA = TMIN to TMAX
∆VPOUT/
∆VSENSE
±1.5
±3.0
TA = TMIN to TMAX
TA = +25°C
±1.5
±3.0
TA = TMIN to TMAX
VSENSE = 0V,
VRS+ = 25V
POUT Output Offset Voltage
(Note 11)
±0.5
3
TA = TMIN to TMAX
% FSO*
%
10
mV
30
MAX4210D/MAX4211D (power gain = 16.67)
POUT Gain Accuracy
(Note 9)
±0.5
±3.0
TA = TMIN to TMAX
±0.5
TA = TMIN to TMAX
*FSO refers to full-scale output under the conditions: VSENSE = 100mV, VRS+ = +25V, or VIN = 1V.
6
±1.5
_______________________________________________________________________________________
±1.5
±3.0
%
High-Side Power and
Current Monitors
(VCC = 5.0V, VRS+ = 25V, VSENSE = 5mV, VIN = 1.0V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
GND, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
∆VPOUT_MAX/
FSO
Total POUT Output Error
(Note 10)
∆VPOUT_MAX/
VPOUT
POUT Output Offset Voltage
(Note 11)
CONDITIONS
VSENSE = 5mV to
100mV, VRS+ = 25V,
VIN = 0.2V to 1V
MIN
TA = +25°C
TYP
MAX
±0.15
±1.5
±3.0
TA = TMIN to TMAX
VSENSE = 150mV, VRS+ TA = +25°C
= 25V, VIN = 600mV
TA = TMIN to TMAX
±0.2
VSENSE = 100mV, VRS+ = 15V,
VIN ≥ 160mV
±2.5
VSENSE = 100mV, VRS+ = 15V,
VIN ≥ 360mV
±1.2
VSENSE = 50mV, VRS+ = 15V,
VIN ≥ 240mV
±1.8
VSENSE = 25mV, VRS+ = 15V,
VIN ≥ 600mV
±1.8
VSENSE = 0V,
VRS+ = 25V, VIN = 1V
TA = +25°C
UNITS
% FSO*
±1.5
±3.0
1.5
TA = TMIN to TMAX
%
5
15
mV
MAX4210E/MAX4211E (power gain = 25.00)
POUT Gain Accuracy
(Note 9)
∆VPOUT/
∆VSENSE
∆VPOUT/
∆VIN
∆VPOUT_MAX/
FSO
Total POUT Output Error
(Note 10)
POUT Output Offset Voltage
(Note 11)
∆VPOUT_MAX/
VPOUT
VSENSE = 10mV to
100mV, VIN = 1V
TA = +25°C
VSENSE = 100mV,
VIN = 0.2V to 1V
TA = +25°C
VSENSE = 5mV to
100mV, VRS+ = 25V,
VIN = 0.2V to 1V
TA = +25°C
VSENSE = 150mV,
VRS+ =25V, VIN =
600mV
TA = +25°C
±0.5
±1.5
±0.5
±1.5
±3.0
TA = TMIN to TMAX
±3.0
TA = TMIN to TMAX
±0.15
±1.5
% FSO*
±3.0
TA = TMIN to TMAX
±0.2
±2.5
VSENSE = 100mV, VRS+ = 15V,
VIN ≥ 360mV
±1.2
VSENSE = 50mV, VRS+ = 15V,
VIN ≥ 240mV
±1.8
VSENSE = 25mV, VRS+ = 15V,
VIN ≥ 600mV
±1.8
TA = +25°C
TA = TMIN to TMAX
±1.5
±3.0
TA = TMIN to TMAX
VSENSE = 100mV, VRS+ = 15V,
VIN ≥ 160mV
VSENSE = 0V,
VRS+ = 25V, VIN = 1V
%
2
%
6.5
20
mV
*FSO refers to full-scale output under the conditions: VSENSE = 100mV, VRS+ = +25V, or VIN = 1V.
_______________________________________________________________________________________
7
MAX4210/MAX4211
ELECTRICAL CHARACTERISTICS (continued)
MAX4210/MAX4211
High-Side Power and
Current Monitors
ELECTRICAL CHARACTERISTICS (continued)
(VCC = 5.0V, VRS+ = 25V, VSENSE = 5mV, VIN = 1.0V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
GND, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
±0.5
±1.5
±0.5
±1.5
UNITS
MAX4210F/MAX4211F (power gain = 40.96)
POUT Gain Accuracy
(Note 9)
∆VPOUT/
∆VSENSE
∆VPOUT/
∆VIN
∆VPOUT_MAX/
FSO
Total POUT Output Error
(Note 10)
∆VPOUT_MAX/
VPOUT
POUT Output Offset Voltage
(Note 11)
VSENSE = 10mV to
100mV, VIN = 1V
TA = +25°C
VSENSE = 100mV,
VIN = 0.2V to 1V
TA = +25°C
VSENSE = 5mV to
100mV, VRS+ = 25V,
VIN = 0.2V to 1V
TA = +25°C
±3.0
TA = TMIN to TMAX
±3.0
TA = TMIN to TMAX
±0.15
±2.5
VSENSE = 100mV, VRS+ = 15V,
VIN ≥ 360mV
±1.2
VSENSE = 50mV, VRS+ = 15V,
VIN ≥ 240mV
±1.8
VSENSE = 25mV, VRS+ = 15V,
VIN ≥ 600mV
±1.8
TA = +25°C
±1.5
±3.0
TA = TMIN to TMAX
VSENSE = 100mV, VRS+ = 15V,
VIN ≥ 160mV
VSENSE = 0V,
VRS+ = 25V, VIN = 1V
%
% FSO*
%
3
TA = TMIN to TMAX
10
30
mV
MAX4211A/MAX4211D (current gain = 16.67)
IOUT Gain Accuracy
∆VIOUT/
∆VSENSE
∆VIOUT_MAX/
FSO
Total IOUT Output Error
(Note 10)
VSENSE = 20mV to
100mV, VRS+ = 25V
TA = +25°C
VSENSE = 5mV to
100mV
TA = +25°C
VSENSE = 150mV
∆VIOUT_MAX/
VIOUT
±0.5
±3.0
TA = TMIN to TMAX
±0.15
±0.2
%
% FSO*
±1.5
±3.0
TA= TMIN to TMAX
VSENSE = 50mV
±1.2
VSENSE = 25mV
±1.8
VSENSE = 5mV
±20
*FSO refers to full-scale output under the conditions: VSENSE = 100mV, VRS+ = +25V, or VIN = 1V.
8
±1.5
±3.0
TA = TMIN to TMAX
TA = +25°C
±1.5
_______________________________________________________________________________________
%
High-Side Power and
Current Monitors
(VCC = 5.0V, VRS+ = 25V, VSENSE = 5mV, VIN = 1.0V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
GND, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = -40°C to +85°C, unless otherwise noted. Typical values are at
TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
±0.5
±1.5
UNITS
MAX4211B/MAX4211E (current gain = 25.00)
IOUT Gain Accuracy
∆VIOUT/
∆VSENSE
∆VIOUT_MAX/
FSO
Total IOUT Output Error
(Note 10)
VSENSE = 20mV to
100mV, VRS+ = 25V
VSENSE = 5mV to
100mV
VSENSE = 150mV
∆VIOUT_MAX/
VIOUT
TA = +25°C
±3.0
TA = TMIN to TMAX
TA = +25°C
±0.15
TA = +25°C
±1.5
±3.0
TA = TMIN to TMAX
±0.2
%
% FSO*
±1.5
±3.0
TA = TMIN to TMAX
VSENSE = 50mV
±1.2
VSENSE = 25mV
±1.8
VSENSE = 5mV
±20
%
MAX4211C/MAX4211F (current gain = 40.96)
IOUT Gain Accuracy
∆VIOUT/
∆VSENSE
∆VIOUT_MAX/
FSO
Total IOUT Output Error
(Note 10)
TA = TMIN to TMAX
VSENSE = 5mV to
100mV
TA = TMIN to TMAX
VSENSE = 100mV
∆VIOUT_MAX/
VIOUT
TA = +25°C
VSENSE = 20mV to
100mV, VRS+ =25V
TA = +25°C
TA = +25°C
±0.5
±1.5
±3.0
±0.15
±1.5
±3.0
±0.2
%
% FSO*
±1.5
±3.0
TA = TMIN to TMAX
VSENSE = 50mV
±1.2
VSENSE = 25mV
±1.8
VSENSE = 5mV
±20
%
*FSO refers to full-scale output under the conditions: VSENSE = 100mV, VRS+ = +25V, or VIN = 1V.
All devices are 100% production tested at TA = +25°C. All temperature limits are guaranteed by design.
Guaranteed by power-supply rejection test.
Guaranteed by output voltage error tests (IOUT).
Guaranteed by output voltage error tests (IOUT or POUT, or both).
IN Input Voltage Range (MAX421_D/E/F) and VRS+ Input Voltage Range (MAX421_A/B/C) are guaranteed by design
(GBD) and not production tested. See Multiplier Transfer Characteristics graphs in the Typical Operating Characteristics.
Note 6: This test does not apply to the low gain options, MAX421_A/D, because OUT is clamped at approximately 4V.
Note 7: The device does not experience phase reversal when overdriven.
Note 8: VPULLUP is defined as an externally applied voltage through a resistor, RPULLUP, to pull up the comparator output.
Note 9: POUT gain accuracy is the sum of gain error and multiplier nonlinearity.
Note 10: Total output voltage error is the sum of gain and offset voltage errors.
Note 11: POUT Output Offset Voltage is the sum of offset and multiplier feedthrough.
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
_______________________________________________________________________________________
9
MAX4210/MAX4211
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VCC = 5.0V, VRS+ = 25V, VSENSE = 100mV, VIN = 1V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
0V, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT
vs. COMMON-MODE VOLTAGE
0.5
0.7
MAX4211
0.6
0.5
MAX4210
0.4
VSENSE = 5mV
VCC = 5V
0.45
VCC = 5.5V
VCC = 4.0V
0.40
0.35
0.30
VCC = 2.7V
MAX4210
0.3
0.25
0.2
0.3
3.1
3.5
3.9
4.3
4.7
5.1
4
5.5
8
12
24
0.20
28
-40
-15
VCC = 5.5V
14
BIAS CURRENT (µA)
VCC = 4.0V
0.6
0.5
VCC = 2.7V
RS+ (A/B/C VERSIONS)
12
VRS+ = VRS- = 25V
10
8
RS-
6
35
60
85
RS+/RS- BIAS CURRENT
vs. COMMON-MODE VOLTAGE
16
MAX4210/11 toc04
VSENSE = 5mV
10
TEMPERATURE (°C)
RS+/RS- BIAS CURRENT
vs. TEMPERATURE
MAX4211
SUPPLY CURRENT vs. TEMPERATURE
0.7
20
RS+ VOLTAGE (V)
SUPPLY VOLTAGE (V)
0.8
16
16
14
RS+ (A/B/C VERSIONS)
BIAS CURRENT (µA)
2.7
MAX4210/11 toc06
0.4
SUPPLY CURRENT (mA)
0.50
SUPPLY CURRENT (mA)
MAX4211
0.6
VSENSE = 5mV
VCC = 5V
MAX4210/11 toc05
SUPPLY CURRENT (mA)
0.7
0.8
MAX4210/11 toc02
VSENSE = 5mV
SUPPLY CURRENT (mA)
MAX4210/11 toc01
0.8
MAX4210
SUPPLY CURRENT vs. TEMPERATURE
MAX4210/11 toc03
SUPPLY CURRENT vs. SUPPLY VOLTAGE
12
10
VRS+ = VRS-
8
6
RS-
4
4
0.4
2
2
RS+ (D/E/F VERSIONS)
RS+ (D/E/F VERSIONS)
0
0
-15
10
35
60
-15
10
35
60
CURRENT OUTPUT ERROR
vs. SUPPLY VOLTAGE
-0.1
-0.3
TA = +25°C
-0.5
TA = +85°C
-0.6
TA = -40°C
-0.2
TA = +25°C
-0.3
-0.4
-0.5
TA = 0°C
TA = +85°C
-0.6
-0.7
-0.8
-0.8
2.7
3.1
3.5
3.9
4.3
4.7
SUPPLY VOLTAGE (V)
10
5.1
5.5
16
20
24
0
-0.2
TA = 0°C
-0.4
-0.6
28
TA = -40°C
-0.8
-1.0
TA = +25°C
-1.2
-1.4
TA = +85°C
-1.6
-0.7
12
POWER OUTPUT ERROR
vs. SENSE VOLTAGE
OUTPUT ERROR (%)
OUTPUT ERROR (%)
TA = 0°C
-0.4
0
MAX4210/11 toc07
-0.1
8
COMMON-MODE VOLTAGE (V)
POWER OUTPUT ERROR
vs. SUPPLY VOLTAGE
TA = -40°C
4
85
TEMPERATURE (°C)
0
-0.2
-40
85
TEMPERATURE (°C)
MAX4210/11 toc08
-40
MAX4210/11 toc09
0.3
OUTPUT ERROR (%)
MAX4210/MAX4211
High-Side Power and
Current Monitors
-1.8
2.7
3.1
3.5
3.9
4.3
4.7
SUPPLY VOLTAGE (V)
5.1
5.5
-2.0
0
25
50
75
100
SENSE VOLTAGE (mV)
______________________________________________________________________________________
125
150
High-Side Power and
Current Monitors
TA = +25°C
-1.2
-1.4
0.2
0
-0.2
-0.6
-1.8
-0.8
-2.0
-1.0
25
50
75
100
125
TA = +25°C
TA = +85°C
-0.4
-1.6
0
10
16
19
22
-1.4
25
0
200
400
24.90
24.85
MAX4211E
24.90
24.85
24.80
85
1000
MAX4211D
VSENSE = 100mV
2.0
1.5
VSENSE = 70mV
VSENSE = 30mV
1.0
0.5
0
-40
-15
10
35
60
0
85
0.3
0.6
0.9
1.2
TEMPERATURE (°C)
IN VOLTAGE (V)
MULTIPLIER TRANSFER CHARACTERISTICS
MULTIPLIER TRANSFER CHARACTERISTICS
REFERENCE VOLTAGE
vs. SUPPLY VOLTAGE
3
2
VRS+ = 4V
1
VSENSE = 70mV
2.0
1.5
VSENSE = 30mV
1.0
1.220
1.5
MAX4210/11 toc18
VSENSE = 100mV
2.5
POUT VOLTAGE (V)
VRS+ = 25V
MAX4211B
REFERENCE VOLTAGE (V)
VRS+ = 15V
4
3.0
MAX4210/11 toc16
MAX4211B
MAX4210/11 toc17
TEMPERATURE (°C)
5
1200
MULTIPLIER TRANSFER CHARACTERISTICS
24.70
60
800
2.5
24.75
24.80
600
IN VOLTAGE (mV)
POUT VOLTAGE (V)
24.95
POUT VOLTAGE (V)
13
24.95
CURRENT GAIN (V/V)
GAIN (1/V)
25.00
35
TA = 0°C
-1.2
CURRENT GAIN vs. TEMPERATURE
25.00
MAX4210/11 toc13
MAX4211E
10
-1.0
VRS+ VOLTAGE (V)
25.05
-15
TA = +25°C
-2.0
7
POWER GAIN vs. TEMPERATURE
-40
TA = +85°C
-0.8
-1.8
MAX4211B
4
150
-0.6
-1.6
SENSE VOLTAGE (mV)
25.10
TA = -40°C
TA = 0°C
MAX4210/11 toc14
-1.0
0.4
TA = -40°C
-0.4
MAX4210/11 toc15
TA = +85°C
-0.8
0.6
-0.2
OUTPUT ERROR (%)
-0.6
0.8
OUTPUT ERROR (%)
OUTPUT ERROR (%)
TA = 0°C
0
MAX4210/11 toc11
TA = -40°C
-0.4
1.0
MAX4210/11 toc10
0
-0.2
POWER OUTPUT ERROR
vs. IN VOLTAGE
POWER OUTPUT ERROR vs. VRS+
MAX4210/11 toc12
CURRENT OUTPUT ERROR
vs. SENSE VOLTAGE
1.215
1.210
1.205
0.5
0
0
0
50
100
150
200
SENSE VOLTAGE (mV)
250
300
1.200
4
8
12
16
20
RS+ VOLTAGE (V)
24
28
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
SUPPLY VOLTAGE (V)
______________________________________________________________________________________
11
MAX4210/MAX4211
Typical Operating Characteristics (continued)
(VCC = 5.0V, VRS+ = 25V, VSENSE = 100mV, VIN = 1V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
0V, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(VCC = 5.0V, VRS+ = 25V, VSENSE = 100mV, VIN = 1V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
0V, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = +25°C, unless otherwise noted.)
COMPARATOR PROPAGATION DELAY
vs. OVERDRIVE VOLTAGE
1.210
1.205
1.4
1.2
1.0
0.8
0.6
0.4
1.8
MAX4210/11 toc21
1.6
PROPAGATION DELAY (µs)
1.215
MAX4210/11 toc20
1.8
MAX4210/11 toc19
REFERENCE VOLTAGE (V)
1.220
COMPARATOR PROPAGATION DELAY
vs. TEMPERATURE
1.6
PROPAGATION DELAY (µs)
REFERENCE VOLTAGE
vs. TEMPERATURE
1.4
1.2
1.0
0.8
0.2
0.6
0
1.200
-40
-15
10
35
60
0
85
50
100
150
200
-40
-15
10
35
60
TEMPERATURE (°C)
OVERDRIVE VOLTAGE (mV)
TEMPERATURE (°C)
COMPARATOR OUTPUT VOLTAGE (VOL)
vs. CURRENT SINK
COMPARATOR OUTPUT VOLTAGE (VOL)
vs. TEMPERATURE
COMPARATOR POWER-UP DELAY
CURRENT SINK = 1mA
350
COUT VOLTAGE (mV)
500
400
300
200
85
MAX4210/11 toc24
MAX4210/11 toc23
400
MAX4210/11 toc22
600
COUT VOLTAGE (mV)
MAX4210/MAX4211
High-Side Power and
Current Monitors
300
5V
VCC
2V/div
0V
250
200
5V
150
COUT
2V/div
100
100
0V
50
0
0
0
1
2
3
-40
4
-15
10
35
60
200µs/div
85
TEMPERATURE (°C)
CURRENT SINK (mA)
COMPARATOR PROPAGATION DELAY
POUT POWER-UP DELAY
COMPARATOR AC RESPONSE
MAX4210/11 toc25
MAX4210/11 toc27
MAX4210/11 toc26
MAX4211E
CIN- = 1.21V
VOD = 5mV
5V
1.45V
CIN+
VCIN+
VCC
2V/div
0V
0.95V
2µs/div
12
5V
5V
2.5V
COUT
2V/div
COUT
2V/div
POUT
1V/div
0V
0V
0V
4µs/div
200µs/div
______________________________________________________________________________________
High-Side Power and
Current Monitors
IOUT POWER-UP DELAY
VCC POWER-UP/DOWN RESPONSE POUT
MAX4210/11 toc28
MAX4211E
MAX4210/11 toc29
5V
VCC
2V/div
VSENSE = 150mV
MAX4211E
VCC
2V/div
0V
0V
2.5V
IOUT
1V/div
POUT
2V/div
0V
0V
200µs/div
2ms/div
VCC POWER-UP/DOWN RESPONSE IOUT
RS POWER-UP/DOWN RESPONSE POUT
MAX4210/11 toc30
MAX4210/11 toc31
VSENSE = 150mV
MAX4211E
10V
VRS+
5V/div
VCC
2V/div
0V
VSENSE
0V
2.5V
POUT
1V/div
IOUT
2V/div
0V
2ms/div
0V
20ms/div
POUT SMALL-SIGNAL PULSE RESPONSE
RS POWER-UP/DOWN RESPONSE IOUT
MAX4210/11 toc33
MAX4210/11 toc32
10V
VRS+
5V/div
VSENSE = 10mV
TO 20mV STEP
0V
470pF
LOAD
2.5V
IOUT
1V/div
POUT
100mV/div
0V
20ms/div
10µs/div
______________________________________________________________________________________
13
MAX4210/MAX4211
Typical Operating Characteristics (continued)
(VCC = 5.0V, VRS+ = 25V, VSENSE = 100mV, VIN = 1V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
0V, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(VCC = 5.0V, VRS+ = 25V, VSENSE = 100mV, VIN = 1V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
0V, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = +25°C, unless otherwise noted.)
POUT LARGE-SIGNAL PULSE RESPONSE
IOUT SMALL-SIGNAL PULSE RESPONSE
MAX4210/11 toc35
MAX4210/11 toc34
470pF
LOAD
VSENSE = 10mV
TO 90mV STEP
VSENSE = 10mV
TO 20mV STEP
470pF
LOAD
POUT
1V/div
IOUT
100mV/div
10µs/div
10µs/div
POUT SLEW-RATE PULSE RESPONSE
IOUT LARGE-SIGNAL PULSE RESPONSE
MAX4210/11 toc37
MAX4210/11 toc36
NO LOAD
470pF
LOAD
VSENSE = 10mV
TO 90mV STEP
VSENSE = 10mV
TO 90mV STEP
POUT
1V/div
POUT
1V/div
10µs/div
10µs/div
POUT COMMON-MODE REJECTION RATIO
vs. FREQUENCY
IOUT SLEW-RATE PULSE RESPONSE
MAX4210/11 toc38
MAX4210/11 toc39
-20
NO LOAD
VSENSE = 100mV
-30
VSENSE = 10mV
TO 90mV STEP
-40
CMRR (dB)
MAX4210/MAX4211
High-Side Power and
Current Monitors
IOUT
1V/div
-50
-60
-70
-80
10µs/div
-90
0.001
0.01
0.1
1
FREQUENCY (MHz)
14
______________________________________________________________________________________
High-Side Power and
Current Monitors
-10
-20
PSR (dB)
-50
-60
-40
15
10
-60
-80
5
-70
0
0.001
-80
10
1
0.1
100
1k
100k
10k
VSENSE = 10mVP-P
30
25
20
10
VSENSE = 90mVP-P
GAIN (dB)
20
15
15
10
10
5
5
0.01
0.1
1
0
0.001
10
0.01
1
0.1
FREQUENCY (MHz)
FREQUENCY (MHz)
IOUT LARGE-SIGNAL GAIN
vs. FREQUENCY
IN SMALL-SIGNAL GAIN
vs. FREQUENCY
5
MAX4210/11 toc45
30
VSENSE = 90mVP-P
0
GAIN (dB)
20
15
-5
MAX4210/11 toc46
0
0.001
25
1
POUT LARGE-SIGNAL GAIN
vs. FREQUENCY
MAX4210/11 toc43
30
0.1
FREQUENCY (MHz)
IOUT SMALL-SIGNAL GAIN
vs. FREQUENCY
25
0.01
FREQUENCY (Hz)
FREQUENCY (MHz)
MAX4210/11 toc44
0.01
GAIN (dB)
-90
0.001
VSENSE = 10mVP-P
20
-30
-50
-70
GAIN (dB)
CMRR (dB)
-40
25
MAX4210/11 toc42
-30
30
GAIN (dB)
VSENSE = 100mV
MAX4210/11 toc41
0
MAX4210/11 toc40
-20
POUT SMALL-SIGNAL GAIN
vs. FREQUENCY
POWER-SUPPLY REJECTION
vs. FREQUENCY
IOUT COMMON-MODE REJECTION RATIO
vs. FREQUENCY
VIN = 10mVP-P
MEASURED AT POUT
VSENSE = 40mV
-10
10
-15
5
0
0.001
0.01
0.1
FREQUENCY (MHz)
1
-20
0.001
0.01
0.1
1
10
FREQUENCY (MHz)
______________________________________________________________________________________
15
MAX4210/MAX4211
Typical Operating Characteristics (continued)
(VCC = 5.0V, VRS+ = 25V, VSENSE = 100mV, VIN = 1V, VLE = 0V, RIOUT = RPOUT = 1MΩ, VCIN1+ = VCIN2+ = VREF, VCIN1- = VCIN2- =
0V, VINHIBIT = 0V, RCOUT1 = RCOUT2 = 5kΩ connected to VCC, TA = +25°C, unless otherwise noted.)
MAX4210/MAX4211
High-Side Power and
Current Monitors
MAX4210A/B/C Pin Description
PIN
6 TDFN
8 µMAX
NAME
FUNCTION
1
1
GND
Ground
2
2, 3, 6
N.C.
No Connection. Not internally connected.
3
4
VCC
Power-Supply Voltage. Connect a 0.1µF bypass capacitor from VCC to GND.
4
5
RS+
Power Connection to External-Sense Resistor and Internal Resistor-Divider
5
7
RS-
Load-Side Connection for External-Sense Resistor
6
8
POUT
EP
—
EP*
Power Output Voltage. Voltage output proportional to source power (input voltage
multiplied by load current).
Exposed Paddle. EP is internally connected to GND.
*TDFN package only.
MAX4210D/E/F Pin Description
PIN
NAME
FUNCTION
6 TDFN
8 µMAX
1
1
GND
2
2
IN
3
4
VCC
4
5
RS+
Power Connection to External-Sense Resistor
5
7
RS-
Load-Side Connection for External-Sense Resistor
6
8
POUT
EP
—
EP*
Exposed Paddle. EP is internally connected to GND.
—
3, 6
N.C.
No Connection. Not internally connected.
Ground
Multiplier Input Voltage. Voltage input for internal multiplier.
Power-Supply Voltage. Connect a 0.1µF bypass capacitor from VCC to GND.
Power Output Voltage. Voltage output proportional to source power (input voltage
multiplied by load current).
*TDFN package only.
16
______________________________________________________________________________________
High-Side Power and
Current Monitors
PIN
NAME
FUNCTION
16 THIN QFN
16 TSSOP
1
3
VCC
Power-Supply Voltage. Connect a 0.1µF bypass capacitor from VCC to GND.
2
4
N.C.
No Connection. Not internally connected.
3
5
LE
4
6
COUT1
Open-Drain Comparator 1 Output. LE and INHIBIT control the comparator 1 output.
5
7
INHIBIT
INHIBIT for Comparator 1 Output. Driving logic high inhibits the comparator
operation. Drive logic low for normal operation.
6
8
COUT2
7
9
GND
8
10
CIN2+
Latch Enable for Comparator 1. Driving logic low makes the comparator
transparent (regular comparator). Driving logic high latches the output.
Open-Drain Comparator 2 Output
Ground
Comparator 2 Positive Input
9
11
CIN2-
Comparator 2 Negative Input
10
12
CIN1+
Comparator 1 Positive Input
11
13
CIN1-
Comparator 1 Negative Input
12
14
REF
1.21V Internal Reference Output
13
15
POUT
Power Output Voltage. Voltage output proportional to source power (input voltage
multiplied by load current).
14
16
IOUT
Current Output Voltage. Voltage output proportional to VSENSE (VRS+ - VRS-) load
current.
15
1
RS-
16
2
RS+
Power Connection to External-Sense Resistor and Internal Resistor-Divider
EP
—
EP*
Exposed Paddle. EP is internally connected to GND.
Load-Side Connection for External-Sense Resistor
*Thin QFN package only.
______________________________________________________________________________________
17
MAX4210/MAX4211
MAX4211A/B/C Pin Description
MAX4210/MAX4211
High-Side Power and
Current Monitors
MAX4211D/E/F Pin Description
PIN
NAME
FUNCTION
16 THIN QFN
16 TSSOP
1
3
VCC
2
4
IN
Multiplier Input Voltage. Voltage input for internal multiplier.
3
5
LE
Latch Enable for Comparator 1. Driving logic low makes the comparator
transparent (regular comparator). Driving logic high latches the output.
4
6
COUT1
Open-Drain Comparator 1 Output. Output controlled by LE and INHIBIT.
INHIBIT for Comparator 1 Output. Driving logic high inhibits the comparator
operation. Drive logic low for normal operation.
5
7
INHIBIT
6
8
COUT2
7
9
GND
8
10
CIN2+
Power-Supply Voltage. Connect a 0.1µF bypass capacitor from VCC to GND.
Open-Drain Comparator 2 Output
Ground
Comparator 2 Positive Input
9
11
CIN2-
Comparator 2 Negative Input
10
12
CIN1+
Comparator 1 Positive Input
11
13
CIN1-
Comparator 1 Negative Input
12
14
REF
1.21V Internal Reference Output
13
15
POUT
Power Output Voltage. Voltage output proportional source power (input voltage
multiplied by load current).
14
16
IOUT
Current Output Voltage. Voltage output proportional VSENSE (VRS+ - VRS-) load
current.
15
1
RS-
Load-Side Connection for External-Sense Resistor
16
2
RS+
Power Connection to External-Sense Resistor
EP
—
EP*
Exposed Paddle. EP is internally connected to GND.
*Thin QFN package only.
Functional Diagrams
VSENSE
+
4V TO
28V
-
RSENSE
+
-
LOAD
RS+
4V TO
28V
LOAD
RS-
RS+
RS-
VCC
+
-
2.7V TO
5.5V
+
MAX4210D
MAX4210E
MAX4210F
25:1
IN
POUT
0 TO 1V
MAX4210A
MAX4210B
MAX4210C
GND
18
-
RSENSE
+
-
VCC
2.7V TO
5.5V
VSENSE
+
POUT
+
-
GND
______________________________________________________________________________________
High-Side Power and
Current Monitors
VSENSE
+
4V TO
28V
-
RSENSE
+
-
LOAD
RS+
4V TO
28V
-
RSENSE
+
-
LOAD
RS-
RS+
VCC
2.7V TO
5.5V
VSENSE
+
RS-
VCC
+
-
2.7V TO
5.5V
+
-
IOUT
25:1
IOUT
IN
POUT
0 TO 1V
1.21V
REFERENCE
INHIBIT
POUT
+
-
REF
CIN1+
1.21V
REFERENCE
INHIBIT
REF
CIN1+
COUT1
COUT1
CIN1-
CIN1LE
LE
CIN2+
CIN2+
COUT2
COUT2
CIN2-
CIN2MAX4211A
MAX4211B
MAX4211C
MAX4211D
MAX4211E
MAX4211F
GND
Detailed Description
The MAX4210/MAX4211 families of current- and powermonitoring ICs integrate a precision current-sense
amplifier and an analog multiplier for a variety of current and power measurements. The MAX4211 integrates an additional uncommitted 1.21V reference and
two comparators with open-drain outputs. These features enable the design of detector circuits for overpower, overcurrent, overvoltage, or any combination of
fault conditions. The MAX4210/MAX4211 offer various
gains, packages, and configurations allowing for
greater design flexibility and lower overall cost.
These devices monitor the load current with their highside current-sense amplifiers and provide an analog
GND
output voltage proportional to that current at IOUT
(MAX4211). This voltage is fed to the analog multiplier
for multiplying the load current with a source voltage to
obtain a voltage proportional to load power at POUT.
Current-Sense Amplifier
The integrated current-sense amplifier is a differential
amplifier that amplifies the voltage across RS+ and RS-.
A sense resistor, RSENSE, is connected across RS+
and RS-. A voltage drop across RSENSE is developed
when a load current is passed through it. This voltage
is amplified and is proportional to the load current. This
voltage is also fed to the analog multiplier for powersensing applications (see the Analog Multiplier section). The current-sense amplifiers feature three gain
options: 16.67V/V, 25.0V/V, and 40.96V/V (see Table 1).
______________________________________________________________________________________
19
MAX4210/MAX4211
Functional Diagrams (continued)
MAX4210/MAX4211
High-Side Power and
Current Monitors
The common-mode voltage range is +4V to +28V and
independent of the supply voltage. With this feature, the
device can monitor the output current of a high-voltage
source while running at a lower system voltage typically
between 2.7V and 5.5V.
The MAX4211 has a current-sense amplifier output. The
voltage at IOUT is proportional to the voltage across
VSENSE:
VIOUT = AVIOUT x VSENSE
where VSENSE is the voltage across RS+ and RS-, and
AVIOUT is the amplifier gain of the device given in Table 1.
Analog Multiplier
The MAX4210/MAX4211 integrate an analog multiplier
that enables real-time monitoring of power delivered to
a load. The voltage proportional to the load current is
fed to one input of the multiplier and a voltage proportional to the source voltage is fed to the other. The analog multiplier multiplies these two voltages to obtain an
output voltage proportional to the load power. The analog multiplier is designed only to operate in the positive
quadrant, that is, the inputs and outputs are always
positive voltages.
For the MAX4210D/E/F and MAX4211D/E/F, the analog
multiplier full-scale input at IN is approximately 1V. This
independent multiplier input allows greater design flexibility when using an external voltage-divider. For the
MAX4210A/B/C and MAX4211A/B/C, an integrated voltage-divider divides the source voltage at the RS+ pin
by a nominal value of 25 and passes this voltage to the
multiplier. Thus, the full-scale input voltage at RS+ is
25V. The integrated, trimmed resistor-dividers reduce
external component count and cost.
The voltage output at POUT is proportional to the output
power:
For the MAX4210A/B/C and MAX4211A/B/C:
VPOUT = AVPOUT x VSENSE x VRS+
For the MAX4210D/E/F and MAX4211D/E/F:
VPOUT = AVPOUT x VSENSE x VIN
Table 1. MAX4211 Current-Sense
Amplifier Gain and Full-Scale Sense
Voltage
where VSENSE is the voltage across RS+ and RS- and
A VPOUT is the amplifier gain of the device given in
Table 2.
Internal Comparators (MAX4211)
The MAX4211 features two uncommitted open-drain
output comparators. These comparators can be configured to trip when load current or power reaches a set
limit. They can also be configured as a window comparator with wire-OR output. Comparator 1 (COUT1)
features latch-enable (LE) and inhibit (INHIBIT) inputs.
When LE is low, the comparator is transparent (it functions as a regular unlatched comparator). When LE is
high, the comparator output (COUT1) is latched. When
high, the INHIBIT input suspends the comparator operation and latches the output to the current state. The
operation of INHIBIT is similar to LE, except it has a different input threshold and wider hysteresis. The INHIBIT logic-high threshold is 1.21V and logic-low threshold
is 0.6V with 0.6V hysteresis. INHIBIT is useful in preventing the comparator from giving false output during
fast RS+ transients. INHIBIT is generally triggered by
an RC network connected to RS+ (see the Applications
Information). Both comparators have a built-in 300µs
blanking period at power-up to prevent false outputs.
The comparator outputs are open drain and they can
be pulled up to V CC, RS+, or any voltage less than
+28V. LE and INHIBIT are internally pulled down by a
1µA source.
Table 2. MAX4210/MAX4211 Power-Sense
Amplifier Gain and Full-Scale Sense
Voltage
POWER-SENSE
AMPLIFIER GAIN
(AVPOUT, 1/V)
FULL-SCALE
SENSE VOLTAGE
(mV)
MAX4210A
0.667
150
MAX4210B
1.000
150
MAX4210C
1.640
100
MAX4210D
16.670
150
MAX4210E
25.000
150
MAX4210F
40.960
100
PART
CURRENT-SENSE
AMPLIFIER GAIN
(AVIOUT, V/V)
FULL-SCALE
SENSE VOLTAGE
(mV)
MAX4211A
0.667
150
MAX4211B
1.000
150
MAX4211C
1.640
100
MAX4211A/D
16.67
150
MAX4211D
16.670
150
MAX4211B/E
25.00
150
MAX4211E
25.000
150
MAX4211C/F
40.96
100
MAX4211F
40.960
100
PART
20
______________________________________________________________________________________
High-Side Power and
Current Monitors
Typical Operating Circuit
+
4V TO
28V
VSENSE
-
RSENSE
+
-
LOAD
RS+
RS-
VCC
2.7V TO
5.5V
+
-
C1
IOUT
25:1
POUT
RP
1.21V
REFERENCE
R7
REF
VPULLUP
INHIBIT
CIN1+
R3
R1
COUT1
CIN1-
VPULLUP
LE
CIN2+
R6
R2
R4
COUT2
CIN2MAX4211A
MAX4211B
MAX4211C
GND
R5
______________________________________________________________________________________
21
MAX4210/MAX4211
the comparators’ inputs. This is the comparison reference voltage. If a lower reference voltage is needed,
use an external voltage-divider. The reference can
source or sink a load current up to 100µA.
Internal Reference (MAX4211)
The MAX4211 features a 1.21V bandgap reference output, stable over supply voltage and temperature.
Typically, the reference output is connected to one of
MAX4210/MAX4211
High-Side Power and
Current Monitors
Applications Information
Recommended Component Values
Ideally, the maximum load current develops the fullscale sense voltage across the current-sense resistor.
Choose the gain version needed to yield the maximum
current-sense amplifier output voltage without saturating it. The typical high-side saturation voltage is about
VCC - 0.25V. The current-sense amplifier output voltage
is given by:
VIOUT = VSENSE x AVIOUT
where VIOUT is the voltage fed to the analog multiplier
or at IOUT. VSENSE is the sense voltage. AVIOUT is the
current-sense amplifier gain of the device specified in
Table 1. Calculate the maximum value for RSENSE so
the differential voltage across RS+ and RS- does not
exceed the full-scale sense voltage:
RSENSE =
VSENSE(FULL−SCALE)
ILOAD(FULL−SCALE)
Choose the highest value resistance possible to maximize VSENSE and thus minimize total output error. In
applications monitoring high current, ensure that
RSENSE is able to dissipate its own I2R power dissipation. If the resistor’s power dissipation is exceeded, its
value can drift or it can fail altogether, causing a differential voltage across the terminals in excess of the
absolute maximum ratings. Use resistors specified for
current-sensing applications.
Window Comparator
In some applications where undercurrent or underpower (open-circuit fault) and overcurrent or overpower
(short-circuit fault) needs to be monitored, a window
comparator is desirable. Figure 1 shows a simple circuit
suitable for window detection. Let POVER be the minimum load power required to cause a low state at
COUT2, and let PUNDER be the maximum load current
required to cause a high state at COUT1:
PUNDER (WATTS) =
POVER (WATTS) =
 R1 + R2 
VREF

AVPOUT × RSENSE 
R2

 R4 + R5 
VREF

AVPOUT × RSENSE 
R5

where AVPOUT is the power-sense amplifier gain given
in Table 2, and VREF is the internal reference voltage
(1.2V, typ). The resulting comparator output is high
22
when the current is inside the current window and low
when the current is outside the window. Note that
COUT1 and COUT2 are wire-ORed together.
Overpower Circuit Breaker
Figure 2 shows a circuit breaker that shuts off current to
the load when an overpower fault is detected (the same
circuit can be used to detect overcurrent conditions by
connecting the R1-R2 resistor-divider to IOUT, instead
of POUT). This circuit is useful for protecting the battery
from short-circuit or overpower conditions. When a
power fault is detected, the P-MOSFET, M1, is turned
off and stays off until the manual reset button is
pressed. Also, cycling the input power causes the LE
pin to go low, which unlatches the comparator output
OUT1 and resets the circuit breaker.
During power-up or when the characteristics of the load
change, there can be an inrush current into the load. The
temporary inrush current results in a higher voltage at
POUT. This can bring the voltage at CIN+ above the reference voltage at CIN-, and, as a result, COUT1 goes
high triggering the circuit-breaker function. This unwanted
behavior can be disabled by bringing comparator 1’s
INHIBIT input high. An RC network connected to INHIBIT
(R4 and C1) can be incorporated to suspend comparator
1’s operation for a brief period. In this way, short surges in
load power can be made invisible to the circuit-breaker
function, while longer term overpower load demands (or a
load short circuit) still “trip the breaker.”
The logic-high threshold for INHIBIT is typically 1.2V,
and the logic-low threshold is 0.6V. During power-up,
INHIBIT quickly exceeds 1.2V through C1 and inhibits
COUT1 from changing state. The comparator inputs are
“inhibited” until the INHIBIT voltage is discharged to
0.6V. R3 is a current-limiting resistor, typically 10kΩ,
which protects the INHIBIT input. Since INHIBIT is a
high-impedance input, R3 has no effect on the R4-C1
charge/discharge time. The time during which the comparator is suspended is approximated by:
 ∆V 
tINHIBIT = R4 × C1 In 

 0.6V 
where ∆V is the voltage change at the load. For
improved transient immunity, tINHIBIT can be increased
as required, with the understanding that the breaker
function will be suspended for this period.
If any comparator is not used, its input must be biased
to a known state. For example, connect CIN+ to VCC
and CIN- to GND.
______________________________________________________________________________________
High-Side Power and
Current Monitors
4V TO
28V
VSENSE
MAX4210/MAX4211
+
-
RSENSE
+
-
LOAD
RS+
RS-
VCC
2.7V TO
5.5V
+
-
IOUT
25:1
POUT
1.21V
REFERENCE
REF
VPULLUP
R1
INHIBIT
CIN1+
COUT1
CIN1-
R2
LE
CIN2+
OVER/
UNDERPOWER
R4
COUT2
CIN2MAX4211A
MAX4211B
MAX4211C
GND
R5
Figure 1. Window Comparator for Detecting Underpower and Overpower Faults (Also Detects Undercurrent and Overcurrent Faults
by R1 and R4 to IOUT Instead of POUT)
Variable-Gain Amplifier
Figure 3 shows single-ended input, variable-gain amplifiers (VGA). This VGA features more than 200kHz bandwidth and is useful in automatic gain-control circuits
commonly found in baseband processors. The gain is
controlled by applying 0 to 1V to IN (V GC ) of the
MAX4210D/E/F; 0V corresponds to minimum gain and
1V corresponds to maximum gain.
Measure Load Power
The MAX4210A/B/C and MAX4211A/B/C have internal
voltage-divider resistors connected to RS+ and the
analog multiplier input. This configuration measures
source power accurately and provides protection to the
power source such as a battery. To measure the load
power accurately, choose the MAX4210D/E/F and
MAX4211D/E/F with an external resistor-divider connected directly to the load as shown in Figure 4. This
configuration improves the load-power measurement
accuracy by excluding the additional power dissipated
by RSENSE.
Power-Supply Bypassing
Bypass VCC to GND with a 0.1µF ceramic capacitor to
isolate the IC from supply-voltage transients. To prevent high-frequency coupling, bypass RS+ or RS- with
a 0.1µF capacitor. On the TDFN and thin QFN packages, there is an exposed paddle that does not carry
any current, but should also be connected to the
ground plane for rated power dissipation.
______________________________________________________________________________________
23
MAX4210/MAX4211
High-Side Power and
Current Monitors
VSENSE
+
4V TO
28V
-
M1
RSENSE
+
-
LOAD
R5
RS+
RS-
VCC
2.7V TO
5.5V
+
-
C1
IOUT
25:1
POUT
R3
1.21V
REFERENCE
R4
INHIBIT
REF
R1
CIN1+
COUT1
CIN1-
R2
LE
CIN2+
COUT2
MANUAL
RESET
CIN2MAX4211A
MAX4211B
MAX4211C
RESET
(FROM µC)
GND
Figure 2. Overpower Circuit Breaker (For a Detailed Example, Refer to the MAX4211E EV Kit)
24
______________________________________________________________________________________
High-Side Power and
Current Monitors
MAX4210/MAX4211
VCC
MAX4210D/E/F
RS+
POUT
R2
OUTPUT
RSIN
VOUTPUT = VINPUT ✕
(R2/R1) ✕ AVPOUT ✕ VIN
INPUT
VIN
GAIN CONTROL
(0 TO 1V)
R1
Figure 3. Single-Ended-Input, Variable-Gain Amplifier
VSENSE
+
4V TO
28V
-
RSENSE
+
RS+
RS-
LOAD
VCC
2.7V TO
5.5V
+
MAX4210D/E/F
MAX4211D/E/F
POUT
IN
GND
Figure 4. Load-Power Measurement with External Voltage-Divider
______________________________________________________________________________________
25
POWER GAIN (1/V)
CURRENT/
POWER
MEASUREMENT
OUTPUT
NO. OF COMPARATORS
INTERNAL
REFERENCE
VOLTAGEMULTIPLIER INPUT
(INTERNAL
RESISTOR-DIVIDER/
EXTERNAL INPUT)
FULL-SCALE VSENSE
VOLTAGE (mV)
Selector Guide
CURRENT GAIN
(V/V)
MAX4210/MAX4211
High-Side Power and
Current Monitors
MAX4210AETT
6 TDFN
—
0.667
P
None
N
INT
150
MAX4210AEUA
8 µMAX
—
0.667
P
None
N
INT
150
MAX4210BETT
6 TDFN
—
1.000
P
None
N
INT
150
MAX4210BEUA
8 µMAX
—
1.000
P
None
N
INT
150
MAX4210CETT
6 TDFN
—
1.640
P
None
N
INT
100
MAX4210CEUA
8 µMAX
—
1.640
P
None
N
INT
100
MAX4210DETT
6 TDFN
—
16.670
P
None
N
EXT
150
MAX4210DEUA
8 µMAX
—
16.670
P
None
N
EXT
150
MAX4210EETT
6 TDFN
—
25.000
P
None
N
EXT
150
MAX4210EEUA
8 µMAX
—
25.000
P
None
N
EXT
150
MAX4210FETT
6 TDFN
—
40.960
P
None
N
EXT
100
MAX4210FEUA
8 µMAX
—
40.960
P
None
N
EXT
100
MAX4211AETE
16 Thin QFN
16.67
0.667
C/P
2
Y
INT
150
MAX4211AEUE
16 TSSOP
16.67
0.667
C/P
2
Y
INT
150
MAX4211BETE
16 Thin QFN
25.00
1.000
C/P
2
Y
INT
150
MAX4211BEUE
16 TSSOP
25.00
1.000
C/P
2
Y
INT
150
MAX4211CETE
16 Thin QFN
40.96
1.640
C/P
2
Y
INT
100
MAX4211CEUE
16 TSSOP
40.96
1.640
C/P
2
Y
INT
100
MAX4211DETE
16 Thin QFN
16.67
16.670
C/P
2
Y
EXT
150
MAX4211DEUE
16 TSSOP
16.67
16.670
C/P
2
Y
EXT
150
MAX4211EETE
16 Thin QFN
25.00
25.000
C/P
2
Y
EXT
150
MAX4211EEUE
16 TSSOP
25.00
25.000
C/P
2
Y
EXT
150
MAX4211FETE
16 Thin QFN
40.96
40.960
C/P
2
Y
EXT
100
MAX4211FEUE
16 TSSOP
40.96
40.960
C/P
2
Y
EXT
100
PART
PINPACKAGE
C = Current Measurement Output Available (IOUT).
P = Power Measurement Output Available (POUT).
Y = Yes.
N = No.
INT = Internal Resistor-Divider.
EXT = External Input Pin.
26
______________________________________________________________________________________
High-Side Power and
Current Monitors
PART
TEMP RANGE
PIN-PACKAGE
6 TDFN-6-EP*
(3mm x 3mm)
MAX4210BETT
-40°C to +85°C
MAX4210BEUA
-40°C to +85°C 8 µMAX
MAX4210CETT
-40°C to +85°C
MAX4210CEUA
-40°C to +85°C 8 µMAX
MAX4210DETT
-40°C to +85°C
MAX4210DEUA
-40°C to +85°C 8 µMAX
MAX4210EETT
-40°C to +85°C
MAX4210EEUA
-40°C to +85°C 8 µMAX
MAX4210FETT
-40°C to +85°C
MAX4210FEUA
-40°C to +85°C 8 µMAX
MAX4211AETE
-40°C to +85°C
MAX4211AEUE
-40°C to +85°C 16 TSSOP
MAX4211BETE
-40°C to +85°C
MAX4211BEUE
-40°C to +85°C 16 TSSOP
MAX4211CETE
-40°C to +85°C
MAX4211CEUE
-40°C to +85°C 16 TSSOP
MAX4211DETE
-40°C to +85°C
MAX4211DEUE
-40°C to +85°C 16 TSSOP
MAX4211EETE
-40°C to +85°C
MAX4211EEUE
-40°C to +85°C 16 TSSOP
MAX4211FETE
-40°C to +85°C
MAX4211FEUE
-40°C to +85°C 16 TSSOP
6 TDFN-6-EP*
(3mm x 3mm)
6 TDFN-6-EP*
(3mm x 3mm)
6 TDFN-6-EP*
(3mm x 3mm)
6 TDFN-6-EP*
(3mm x 3mm)
16 Thin QFN-EP*
(4mm x 4mm)
16 Thin QFN-EP*
(4mm x 4mm)
16 Thin QFN-EP*
(4mm x 4mm)
16 Thin QFN-EP*
(4mm x 4mm)
16 Thin QFN-EP*
(4mm x 4mm)
16 Thin QFN-EP*
(4mm x 4mm)
TOP
MARK
Chip Information
MAX4210 TRANSISTOR COUNT: 515
MAX4211 TRANSISTOR COUNT: 1032
PROCESS: BiCMOS
AHG
—
AHH
—
AHI
—
AHJ
—
AHK
—
—
—
—
—
—
—
—
—
—
—
—
—
*EP = Exposed paddle.
______________________________________________________________________________________
27
MAX4210/MAX4211
Ordering Information (continued)
High-Side Power and
Current Monitors
MAX4210/MAX4211
Pin Configurations
POUT
RS-
RS+
TOP VIEW
6
5
4
MAX4210
1
1
8
2
7
RS-
N.C.
3
6
N.C.
VCC
4
5
RS+
VCC
(IN) N.C.
MAX4210
POUT
µMAX
3
2
GND
GND
(IN) N.C.
REF
CIN1-
CIN1+
CIN2-
3mm x 3mm TDFN
12
11
10
9
POUT 13
8
CIN2+
IOUT 14
7
GND
MAX4211
RS- 15
1
2
3
4
VCC
(IN) N.C.
LE
COUT1
RS+ 16
6
COUT2
5
INHIBIT
RS- 1
16 IOUT
RS+ 2
15 POUT
VCC 3
14 REF
(IN) N.C. 4
MAX4211
13 CIN1-
LE 5
12 CIN1+
COUT1 6
11 CIN2-
INHIBIT 7
10 CIN2+
COUT2 8
9
GND
TSSOP
4mm x 4mm THIN QFN
( ) ARE FOR MAX421_D/E/F.
28
______________________________________________________________________________________
High-Side Power and
Current Monitors
6, 8, &10L, DFN THIN.EPS
D2
D
A2
PIN 1 ID
N
0.35x0.35
b
PIN 1
INDEX
AREA
E
[(N/2)-1] x e
REF.
E2
DETAIL A
e
k
A1
CL
A
CL
L
L
e
e
PACKAGE OUTLINE, 6,8,10 & 14L,
TDFN, EXPOSED PAD, 3x3x0.80 mm
-DRAWING NOT TO SCALE-
21-0137
G
1
2
COMMON DIMENSIONS
MIN.
MAX.
D
0.70
2.90
0.80
3.10
E
A1
2.90
0.00
3.10
0.05
L
k
0.20
0.40
0.25 MIN.
A2
0.20 REF.
SYMBOL
A
PACKAGE VARIATIONS
PKG. CODE
N
D2
E2
e
JEDEC SPEC
b
[(N/2)-1] x e
DOWNBONDS
ALLOWED
T633-1
6
1.50–0.10
2.30–0.10
0.95 BSC
MO229 / WEEA
0.40–0.05
1.90 REF
NO
T633-2
6
1.50–0.10
2.30–0.10
0.95 BSC
MO229 / WEEA
0.40–0.05
1.90 REF
NO
T833-1
8
1.50–0.10
2.30–0.10
0.65 BSC
MO229 / WEEC
0.30–0.05
1.95 REF
NO
T833-2
8
1.50–0.10
2.30–0.10
0.65 BSC
MO229 / WEEC
0.30–0.05
1.95 REF
NO
T833-3
8
1.50–0.10
2.30–0.10
0.65 BSC
MO229 / WEEC
0.30–0.05
1.95 REF
YES
T1033-1
10
1.50–0.10
2.30–0.10
0.50 BSC
MO229 / WEED-3
0.25–0.05
2.00 REF
NO
T1433-1
14
1.70–0.10
2.30–0.10
0.40 BSC
----
0.20–0.05
2.40 REF
YES
T1433-2
14
1.70–0.10
2.30–0.10
0.40 BSC
----
0.20–0.05
2.40 REF
NO
PACKAGE OUTLINE, 6,8,10 & 14L,
TDFN, EXPOSED PAD, 3x3x0.80 mm
-DRAWING NOT TO SCALE-
21-0137
G
2
2
NOTE: THE TDFN EXPOSED PADDLE SIZE-VARIATION PACKAGE CODE: T633-1
______________________________________________________________________________________
29
MAX4210/MAX4211
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
24L QFN THIN.EPS
MAX4210/MAX4211
High-Side Power and
Current Monitors
PACKAGE OUTLINE,
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm
21-0139
D
1
2
PACKAGE OUTLINE,
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm
21-0139
D
2
2
NOTE: THE THIN QFN EXPOSED PADDLE SIZE-VARIATION PACKAGE CODE: T1644-4
30
______________________________________________________________________________________
High-Side Power and
Current Monitors
8
INCHES
DIM
A
A1
A2
b
E
fl 0.50–0.1
H
c
D
e
E
H
0.6–0.1
L
1
1
α
0.6–0.1
S
BOTTOM VIEW
D
MIN
0.002
0.030
MAX
0.043
0.006
0.037
0.010
0.014
0.005
0.007
0.116
0.120
0.0256 BSC
0.116
0.120
0.188
0.198
0.016
0.026
6
0
0.0207 BSC
8LUMAXD.EPS
4X S
8
MILLIMETERS
MAX
MIN
0.05
0.75
1.10
0.15
0.95
0.25
0.36
0.13
0.18
2.95
3.05
0.65 BSC
2.95
3.05
4.78
5.03
0.41
0.66
0
6
0.5250 BSC
TOP VIEW
A1
A2
A
α
c
e
FRONT VIEW
b
L
SIDE VIEW
PROPRIETARY INFORMATION
TITLE:
PACKAGE OUTLINE, 8L uMAX/uSOP
APPROVAL
DOCUMENT CONTROL NO.
21-0036
REV.
J
1
1
______________________________________________________________________________________
31
MAX4210/MAX4211
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
TSSOP4.40mm.EPS
MAX4210/MAX4211
High-Side Power and
Current Monitors
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
32 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.