TI1 C3225X7R1C226M250AC 3.5 v to 36 v wide-vin synchronous 2.1 mhz step-down converter Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
LM53603 (3 A), LM53602 (2 A) 3.5 V to 36 V Wide-VIN Synchronous 2.1 MHz Step-Down
Converters
1 Features
3 Description
•
•
The LM53603 and LM53602 buck regulators are
specifically designed for 12-V industrial and
automotive applications, providing an adjustable
output voltage from 3.3 V to 10 V at 3 A or 2 A, from
an input voltage of up to 36 V. Advanced high-speed
circuitry allows the device to regulate from an input of
up to 20 V, while providing an output of 5 V at a
switching frequency of 2.1 MHz. The innovative
architecture allows the device to regulate a 3.3-V
output from an input voltage of only 3.5 V. All aspects
of this product are optimized for the industrial and
automotive customer. An input voltage range up to 36
V, with transient tolerance up to 42 V, eases input
surge protection design. An open-drain reset output,
with filtering and delay, provides a true indication of
system status. This feature negates the requirement
for an additional supervisory component, saving cost
and board space. Seamless transition between PWM
and PFM modes, along with a no-load operating
current of only 24 µA, ensures high efficiency and
superior transient response at all loads.
1
•
•
•
•
•
•
•
•
•
•
•
3-A or 2-A Maximum Load Current
Input Voltage Range From 3.5 V to 36 V:
Transients to 42 V
Adjustable Output Voltage From 3.3 V to 10 V
2.1-MHz Fixed Switching Frequency
±2% Output Voltage Tolerance
–40°C to 150°C Junction Temperature Range
1.7-µA Shutdown Current (Typical)
24-µA Input Supply Current at No Load (Typical)
Reset Output With Filter and Delay
Automatic Light Load Mode for Improved
Efficiency
User-Selectable Forced PWM Mode (FPWM)
Built-In Loop Compensation, Soft-Start, Current
Limit, Thermal Shutdown, UVLO, and External
Frequency Synchronization
Thermally Enhanced 16-Lead Package:
5 mm × 4.4 mm × 1 mm
2 Applications
•
•
•
•
Industrial Power Supplies in Building and Factory
Automation
Battery Operated Devices
Low-noise and Low-EMI Applications
Optical Communication Systems
Simplified Schematic
Device Information(1)
PART NUMBER
LM53603
LM53602
PACKAGE
HTSSOP (16)
BODY SIZE (NOM)
5.00 mm x 4.40 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Industrial Power Supply With 5-V, 3-A Output
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
4
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
4
4
5
5
6
7
8
9
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
System Characteristics .............................................
Timing Requirements ................................................
Typical Characteristics ..............................................
9
9.1
9.2
9.3
9.4
Overview ................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
Application Information............................................
Typical Applications ................................................
Typical Adjustable Industrial Application Circuit .....
Do's and Don't's ......................................................
18
18
28
28
10 Power Supply Recommendations ..................... 29
11 Layout................................................................... 30
11.1 Layout Guidelines ................................................. 30
11.2 Layout Example .................................................... 32
12 Device and Documentation Support ................. 33
12.1
12.2
12.3
12.4
12.5
12.6
12.7
12.8
Detailed Description ............................................ 10
8.1
8.2
8.3
8.4
Application and Implementation ........................ 18
10
10
11
15
Device Support ....................................................
Documentation Support ........................................
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
33
33
33
34
34
34
34
34
13 Mechanical, Packaging, and Orderable
Information ........................................................... 34
4 Revision History
2
DATE
REVISION
NOTES
November 2016
*
Initial release.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
5 Device Comparison Table
(1)
PART NUMBER (1)
OUTPUT VOLTAGE
MAXIMUM OUTPUT
CURRENT
LM53603AMPWPR
Adjustable
3A
2000
PACKAGE QTY
LM53603AMPWPT
Adjustable
3A
250
LM53602AMPWPR
Adjustable
2A
2000
LM53602AMPWPT
Adjustable
2A
250
Some text and images in this datasheet refer to fixed 3.3-V or 5-V output devices which are only available in the automotive grade
version of this device as the LM53603-Q1 and LM53602-Q1. Refer to the automotive datasheet for more information on those output
voltage options.
6 Pin Configuration and Functions
PWP Package
16-Lead HTSSOP
Top View
SW
1
16
PGND
SW
2
15
PGND
CBOOT
3
14
N/C
VCC
4
13
VIN
BIAS
5
12
VIN
SYNC
6
EP
(17)
11
EN
AGND
FPWM
7
10
RESET
8
9
FB
Pin Functions
PIN
NO.
NAME
1, 2
I/O (1)
DESCRIPTION
SW
P
Regulator switch node. Connect to power inductor. Connect pins 1 and 2 directly together at the PCB.
3
CBOOT
P
Bootstrap supply input for gate drivers. Connect a high-quality, 470-nF capacitor from this pin to SW.
4
VCC
O
Internal 3.15-V regulator output. Used as supply to internal control circuits. Do not connect to any
external loads. Can be used as logic supply for control inputs. Connect a high-quality, 3.3-µF capacitor
from this pin to GND.
5
BIAS
P
Input to internal voltage regulator. Connect to output voltage point. Do not ground. Connect a highquality, 0.1-µF capacitor from this pin to GND.
6
SYNC
I
Synchronization input to regulator. Used to synchronize the regulator switching frequency to the system
clock. When not used connect to GND; do not float.
7
FPWM
I
Mode control input to regulator. High = forced PWM (FPWM). Low = auto mode; automatic transition
between PFM and PWM. Do not float.
8
RESET
O
Open-drain reset output. Connect to suitable voltage supply through a current limiting resistor. High =
power OK. Low = fault. RESET goes low when EN = low.
9
FB
I
Feedback input to regulator. Connect to output voltage sense point for fixed 5-V and 3.3-V output.
Connect to feedback divider tap point for ADJ option. Do not float or ground.
10
AGND
G
Analog ground for regulator and system. All electrical parameters are measured with respect to this pin.
Connect to EP and PGND on PCB.
11
EN
I
Enable input to the regulator. High = ON. Low = OFF. Can be connected directly to VIN. Do not float.
12, 13
VIN
P
Input supply to the regulator. Connect a high-quality bypass capacitor(s) from this pin to PGND.
Connect pins 12 and 13 directly together at the PCB.
14
N/C
—
This pin has no connection to the device.
(1)
O = Output, I = Input, G = Ground, P = Power
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
3
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
Pin Functions (continued)
PIN
I/O (1)
DESCRIPTION
NO.
NAME
15, 16
PGND
G
Power ground to internal low-side MOSFET. Connect to AGND and system ground. Connect pins 15
and 16 directly together at the PCB.
EP
G
Exposed die attach paddle. Connect to ground plane for adequate heat sinking and noise reduction.
17
7 Specifications
7.1 Absolute Maximum Ratings
over the recommended operating junction temperature range of –40°C to 150°C (unless otherwise noted) (1)
MIN
MAX
UNIT
VIN to AGND, PGND (2)
PARAMETER
–0.3
40
V
SW to AGND, PGND (3)
–0.3
VIN + 0.3
V
CBOOT to SW
–0.3
3.6
V
EN to AGND, PGND (2)
–0.3
40
V
BIAS to AGND, PGND
–0.3
16
V
FB to AGND, PGND : fixed 5 V and 3.3 V
–0.3
16
V
FB to AGND, PGND : ADJ
–0.3
5.5
V
RESET to AGND, PGND
–0.3
8
V
SYNC, FPWM, to AGND, PGND
–0.3
5.5
V
VCC to AGND, PGND
–0.3
4.2
V
RESET pin current (4)
–0.1
1.2
mA
AGND to PGND (5)
–0.3
0.3
V
Storage temperature, Tstg
–40
150
°C
(1)
(2)
(3)
(4)
(5)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Values given
are D.C.
A maximum of 42 V can be sustained at this pin for a duration of ≤ 500 ms at a duty cycle of ≤ 0.01%.
Transients on this pin, not exceeding –3 V or +40 V, can be tolerated for a duration of ≤ 100 ns. For transients between 40 V and 42 V,
see note (2).
Positive current flows into this pin.
A transient voltage of ±2 V can be sustained for ≤1 µs.
7.2 ESD Ratings
VALUE
Human-body model (HBM), per ANSI/ESDA/JEDEC JS001 (1)
V(ESD)
(1)
(2)
4
Electrostatic
discharge
Charged-device model (CDM), per JEDEC specification
JESD22-C101 (2)
Pins 1, 2, 3, 12, 13,
±1500
Pins 11, 5, 8, 9, 6, 7, 4
±2500
Pins 3, 4, 5, 6, 7, 11, 12
and 13
±750
Pins 1, 2, 8, 9, 15 and 16
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
7.3 Recommended Operating Conditions
over the recommended operating junction temperature range of –40°C to 150°C (unless otherwise noted)
MIN
Input voltage
(1)
NOM
MAX
3.9
36
Output voltage : fixed 5 V (2)
0
5
Output voltage : fixed 3.3 V (2)
0
3.3
Output voltage adjustment range: ADJ (2) (3)
UNIT
V
V
V
3.3
10
V
Output current for LM53603
0
3
A
Output current for LM53602
0
2
A
RESET pin current
0
1
mA
–40
150
°C
Operating junction temperature (4)
(1)
(2)
(3)
(4)
See System Characteristics for details of input voltage range.
Under no conditions should the output voltage be allowed to fall below zero volts.
An extended output voltage range to 10 V is possible with changes to the typical application schematic. Also, some system
specifications are not achieved for output voltages greater than 6 V. Consult the factory for further information.
High junction temperatures degrade operating lifetimes. Operating lifetime is de-rated for junction temperatures greater than 125°C.
7.4 Thermal Information
THERMAL METRIC
(1)
LM53603,
LM53602
PWP (HTSSOP)
UNIT
16 PINS
RθJA
Junction-to-ambient thermal resistance
42.5
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
22.6
°C/W
RθJB
Junction-to-board thermal resistance
16.2
°C/W
ψJT
Junction-to-top characterization parameter
0.6
°C/W
ψJB
Junction-to-board characterization parameter
16.0
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
1.1
°C/W
(1)
The values given in this table are only valid for comparison with other packages and cannot be used for design purposes. These values
were calculated in accordance with JESD 51-7, and simulated on a 4-layer JEDEC board. They do not represent the performance
obtained in an actual application. For design information please see the Maximum Ambient Temperature section. For more information
about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report and the Using
New Thermal Metrics (SBVA025) application report.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
5
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
7.5 Electrical Characteristics
Limits apply to the recommended operating junction temperature range of –40°C to 150°C, unless otherwise noted. Minimum
and maximum limits are verified through test, design, or statistical correlation. Typical values represent the most likely
parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated the following conditions
apply: VIN = 13.5 V.
PARAMETER
Initial reference voltage accuracy
for 5-V and 3.3-V options
VFB
VREF
Reference voltage for ADJ option
VIN-operate
Minimum input voltage to
operate (2)
TEST CONDITIONS
MIN (1)
TYP
MAX (1)
VIN = 3.8 V to 36 V, FPWM,
TJ = 25°C
–1%
1%
VIN = 3.8 V to 36 V, FPWM
–1.25%
1.25%
VIN = 3.8 V to 36 V, FPWM,
TJ = 25°C
0.993
1
1.007
VIN = 3.8 V to 36 V, FPWM,
TJ = –40°C to 125°C
0.99
1
1.01
UNIT
V
Rising
3.2
3.95
Falling
2.9
3.55
V
13
µA
Hysteresis, below
0.34
IQ
Operating quiescent current;
measured at VIN pin (3) (4)
VBIAS = 5 V,
TJ = –40°C to 125°C
ISD
Shutdown quiescent current;
measured at VIN pin
EN ≤ 0.4 V, TJ = 25°C
IB
Current into the BIAS pin (4)
VBIAS = 5 V, FPWM = 3.3 V
47
IEN
Current into EN pin
VIN = VEN = 13.5 V
2.3
µA
IFB
Bias current into FB pin
ADJ option
10
nA
RESET upper threshold voltage
Rising, % of nominal Vout
105%
107%
110%
RESET lower threshold voltage
Falling, % of nominal Vout
92%
94%
96.5%
RESET lower threshold voltage
with respect to output voltage
Falling, % actual Vout
94.5%
95.7%
VRESET
VRESETHyst
VMIN
1.7
EN ≤ 0.4 V, TJ = 125°C
3.5
RESET hysteresis as a percent of
output voltage set point
Minimum input voltage for proper
RESET function
Low level RESET pin output
voltage
VOL
8
50-µA pullup to RESET pin, VEN = 0 V,
TJ = 25°C
1.5
50-µA pullup to RESET pin, Vin = 1.5 V,
EN = 0 V
0.4
0.5-mA pullup to RESET pin, Vin = 13.5
V, EN = 0 V
0.4
1-mA pullup to RESET pin, Vin = 13.5 V,
EN = 3.3 V
0.4
Rising
1.7
2
0.45
0.55
Enable input threshold voltage
VEN-off
Enable input threshold for full
shutdown (5)
EN input voltage required for complete
shutdown of the regulator, falling.
0.8
VLOGIC
Logic input levels on FPWM and
SYNC pins
VIH
1.5
IHS
High-side switch current limit
ILS
Low-side switch current limit (6)
(2)
(3)
(4)
(5)
(6)
6
µA
1.5%
VEN
(1)
78
µA
Hysteresis, below
V
V
V
V
VIL
0.4
LM53603
4.5
6.2
LM53602
2.4
4.4
LM53603
3
3.6
4.3
LM53602
2
2.4
2.8
V
A
A
Minimum and maximum limits are 100% production tested at 25°C. Limits over the operating temperature range are verified through
correlation using Statistical Quality Control (SQC) methods. Limits are used to calculate Average Outgoing Quality Level (AOQL).
This is the input voltage at which the device starts to operate (rising). The device shuts down when the input voltage goes below this
value minus the hysteresis.
This is the current used by the device, open loop. It does not represent the total input current of the system when in regulation. See
Isupply in System Characteristics
The FB pin is set to 5.5 V for this test.
Below this voltage on the EN input, the device shuts down completely.
See the Current Limit section for an explanation of valley current limit.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
Electrical Characteristics (continued)
Limits apply to the recommended operating junction temperature range of –40°C to 150°C, unless otherwise noted. Minimum
and maximum limits are verified through test, design, or statistical correlation. Typical values represent the most likely
parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated the following conditions
apply: VIN = 13.5 V.
PARAMETER
TEST CONDITIONS
MIN (1)
MAX (1)
TYP
IZC
Zero-cross current limit
FPWM = 0 V
INEG
Negative current limit
FPWM = 3.3 V
–1.5
High-side MOSFET resistance
135
290
Low-side MOSFET resistance
60
125
2.1
2.35
Rdson
Power switch on-resistance
FSW
Switching frequency
FSYNC
Synchronizing frequency range
VCC
Internal VCC voltage
TSD
Thermal shutdown thresholds
VIN = 3.8 V to 18 V
1.85
VIN = 36 V
A
A
1.2
1.9
VBIAS = 3.3 V
Rising
2.1
2.3
mΩ
MHz
MHz
3.15
V
162
Hysteresis, below
UNIT
–0.02
178
18
°C
7.6 System Characteristics
The following specifications apply only to the typical application circuit, shown in Figure 15 with nominal component values.
Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. The
parameters in this table are not ensured.
PARAMETER
VIN-MIN
Minimum input voltage for Vout to
stay within ±2% of regulation (1)
Line Regulation
Regulation
Load Regulation : Auto Mode
Load Regulation : FPWM Mode
ISUPPLY
VDROP
(1)
(2)
Input supply current when in
regulation (2)
Dropout voltage (VIN – VOUT)
TEST CONDITIONS
MIN
TYP
VOUT = 3.3 V, IOUT = 3 A
3.9
VOUT = 3.3 V, IOUT = 1 A
3.55
VOUT = 5 V, VIN = 8 V to 36 V, IOUT = 3 A
7
VOUT = 3.3 V, VIN = 6 V to 36 V, IOUT = 3
A
5
VOUT = 5 V, VIN = 12 V, IOUT = 10 µA to 3
A
77
VOUT = 3.3 V, VIN = 12 V, IOUT = 10 µA to
3A
53
VOUT = 5 V, VIN = 12 V, IOUT = 10 µA to 3
A
12
VOUT = 3.3 V, VIN = 12 V, IOUT = 10 µA to
3A
9
MAX
UNIT
V
mV
mV
mV
VIN = 13.5 V, VOUT = 3.3 V, IOUT = 0 A
24
VIN = 13.5 V, VOUT = 5 V, IOUT = 0 A
34
5-V Option:
VOUT = 4.95 V, IOUT = 3 A, FSW < 1.85
MHz
0.7
5-V Option:
VOUT = 5 V, IOUT = 3 A, FSW = 1.85 MHz
1.8
µA
V
3.3-V Option:
VOUT = 3.27 V, IOUT = 3 A, FSW < 1.85
MHz
0.65
3.3-V Option:
VOUT = 3.3 V, IOUT = 3 A, FSW = 1.85
MHz
1.8
This parameter is valid once the input voltage has risen above VIN-operate and the device has started up.
Includes current into the EN pin, but does not include current due to the external resistive divider in adjustable output versions. See
Input Supply Current section.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
7
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
7.7 Timing Requirements
Limits apply to the recommended operating junction temperature range of –40°C to 150°C, unless otherwise noted. Minimum
and maximum limits are verified through test, design, or statistical correlation. Typical values represent the most likely
parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated the following conditions
apply: VIN = 13.5 V.
MIN
NOM
MAX
UNIT
TON
Minimum switch on-time, VIN = 20 V
50
80
TOFF
Minimum switch off-time, VIN = 3.8 V
125
200
ns
TRESET-act
Delay time to RESET high signal
2
3
4
ms
TRESET-filter
Glitch filter time for RESET function
12
25
45
µs
TSS
Soft-start time
1
2
3
ms
TEN
Turnon delay, CVCC = 1 µF, TJ = 25°C (1)
TW
Short-circuit wait time (Hiccup time)
(1)
8
ns
1
ms
5.5
ms
This is the time from the rising edge of EN to the time that the soft-start ramp begins.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
7.8 Typical Characteristics
1.02
2.2
1.015
2.15
1.01
2.1
Frequency (MHz)
Refrence Voltage (V)
Unless otherwise specified the following conditions apply: VIN = 12 V, TA = 25°C. Specified temperatures are ambient.
1.005
1
0.995
2.05
2
1.95
0.99
1.9
0.985
1.85
0.98
-60
-40
-20
0
20
40
60
Temperature (°C)
80
100
120
1.8
-60
140
-40
-20
Figure 1. Reference Voltage for ADJ Device
20
40
60
Temperature (°C)
80
100
120
140
D002
Figure 2. Switching Frequency
3.5
7
-40°C
27°C
125°C
-40°C
27°C
125°C
3.45
3.4
Valley Current Limit (A)
6
Peak Current Limit (A)
0
D001
5
4
3
2
3.35
3.3
3.25
3.2
3.15
3.1
1
3.05
0
3
0
5
10
15
20
25
Input Voltage (V)
30
35
40
0
Figure 3. High-Side Peak Current Limit for LM53603
10
15
20
25
Input Voltage (V)
30
35
40
D005
Figure 4. Low-Side Valley Current Limit for LM53603
25
0.4
-40°C
27°C
125°C
0.35
-40°C
25°C
125°C
20
0.3
Shutdown Current (µA)
Short Circuit Current (A)
5
D004
0.25
0.2
0.15
0.1
15
10
5
0.05
0
0
0
5
10
15
20
25
Input Voltage (V)
30
35
40
0
5
D006
Figure 5. Short-Circuit Output Current for LM53603
10
15
20
25
Input Voltage (V)
30
35
Product Folder Links: LM53602 LM53603
D003
Figure 6. Shutdown Current
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
40
9
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
8 Detailed Description
8.1 Overview
The LM5360x family of devices are synchronous current mode buck regulators designed specifically for the Wide
Input voltage Industrial and automotive market. The regulator automatically switches between PWM and PFM
depending on load. At heavy loads the device operates in PWM at a switching frequency of 2.1 MHz. The
regulator's oscillator can also be synchronized to an external system clock. At input voltages above about 20 V,
the switching frequency reduces to maintain regulation during conditions of abnormally high battery voltage. At
light loads the mode changes to PFM, with diode emulation allowing DCM. This reduces input supply current and
keeps the efficiency high. The user can also choose to lock the mode in PWM (FPWM) so that the switching
frequency remains constant regardless of load.
A RESET flag is provided to indicate when the output voltage is near its regulation point. This feature includes
filtering and a delay before asserting. This helps to prevent false flag operation during output voltage transients.
Note that, throughout this data sheet, references to the LM53603 apply equally to the LM53602. The difference
between the two devices is the maximum output current and specified MOSFET current limits.
8.2 Functional Block Diagram
SYNC
VCC BIAS
VIN
* = Not used in -ADJ
INT. REG.
BIAS
OSCILLATOR
ENABLE
LOGIC
EN
CBOOT
HS CURRENT
SENSE
1.0 V
Reference
FB
ERROR
AMPLIFIER
*
+
-
+
-
PWM
COMP.
CONTROL
LOGIC
SW
DRIVER
*
LS CURRENT
SENSE
RESET
RESET
CONTROL
MODE
LOGIC
FPWM
AGND
PGND
Copyright © 2016, Texas Instruments Incorporated
10
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
8.3 Feature Description
8.3.1 RESET Flag Output
The RESET function, built-in to the LM53603, has special features not found in the ordinary Power Good
function. A glitch filter prevents false flag operation for short excursions in the output voltage, such as during line
and load transients. Furthermore, there is a delay between the point at which the output voltage is within
specified limits and the flag asserts Power Good. Because the RESET comparator and the regulation loop share
the same reference, the thresholds track with the output voltage. This allows the LM53603 to be specified with a
96.5% maximum threshold, while at the same time specifying a 95% threshold with respect to the actual output
voltage for that device. This allows tighter tolerance than is possible with an external supervisor device. The net
result is a more accurate power-good function while expanding the system allowance for transients, and so forth.
RESET operation can best be understood by reference to Figure 7 and Figure 8. The values for the various filter
and delay times can be found in the Timing Requirements table. Output voltage excursions lasting less than
TRESET-filter, do not trip RESET. Once the output voltage is within the prescribed limits, a delay of TRESET-act is
imposed before RESET goes high.
This output consists of an open-drain NMOS; requiring an external pullup resistor to a suitable logic supply. It
can also be pulled up to either VCC or VOUT, through an appropriate resistor, as desired. If this function is not
needed, the pin should be left floating or grounded. When EN is pulled low, the flag output is also forced low.
With EN low, RESET remains valid as long as the input voltage is ≥ 1.5 V. The maximum current into this pin
should be limited to 1 mA, while the maximum voltage should be less than 8 V.
VOUT
107%
106%
94%
93%
RESET
High = Power Good
Low = Fault
Figure 7. Static RESET Operation
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
11
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
Feature Description (continued)
Glitches do not cause false operation nor reset timer
VOUT
94%
93%
< Treset_filter
RESET
Treset_act
Treset_filter
Treset_act
Figure 8. RESET Timing Behavior
8.3.2 Enable and Start-Up
Start-up and shutdown of the LM53603 are controlled by the EN input. Applying a voltage of ≥ 2 V activates the
device, while a voltage of ≤ 0.8 V is required to shut it down. The EN input may also be connected directly to the
input voltage supply, if this feature is not needed. This input must not be left floating. The LM53603 uses a
reference based soft-start, that prevents output voltage overshoots and large inrush currents as the regulator is
starting up. A typical start-up waveform is shown in Figure 9 along with typical timings.
12
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
Feature Description (continued)
ENInductor Current
500mA/div
RESET
Treset_act
TSS
VOUT
TEN
21ms/div
ms/div
Figure 9. Typical Start-Up Waveform
8.3.3 Current Limit
The LM53603 incorporates valley current limit for normal overloads and for short-circuit protection. In addition,
the low side switch is also protected from excessive negative current when the device is in FPWM mode. Finally,
a high-side peak current limit is employed for protection of the top NMOS FET.
During overloads the low-side current limit, ILS (see Electrical Characteristics), determines the maximum load
current that the LM53603 can supply. When the low-side switch turns on, the inductor current begins to ramp
down. If the current does not fall below ILS before the next turnon cycle, then that cycle is skipped and the lowside FET is left on until the current falls below ILS. This is somewhat different than the more typical peak current
limit, and results in Equation 1 for the maximum load current.
IOUT
max
ILS
VIN VOUT VOUT
˜
2 ˜ FS ˜ L
VIN
(1)
If the above situation persists for more than about 64 clock cycles, the device turns off both high-side and lowside switches for approximately 5.5 ms (see TW in Timing Requirements). If the overload is still present after the
hiccup time, another 64 cycles is counted and the process is repeated. If the current limit is not tripped for two
consecutive clock cycles, the counter is reset. Figure 10 shows the inductor current with a hard short on the
output. The hiccup time allows the inductor current to fall to zero, resetting the inductor volt-second balance. This
is the method used for short-circuit protection and keeps the power dissipation low during a fault. Of course the
output current is greatly reduced in this condition (see Typical Characteristics). A typical short-circuit transient
and recovery is shown in Figure 11.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
13
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
Feature Description (continued)
Short Removed
Short Applied
VOUT, 2V/div
Iinductor, 500mA/div
Iinductor, 2A/div
5ms/div
21ms/div
ms/div
2 ms/div
Figure 10. Inductor Current Bursts in Short Circuit
Figure 11. Short-Circuit Transient and Recovery
The high-side current limit trips when the peak inductor current reaches IHS (see Electrical Characteristics). This
is a cycle-by-cycle current limit and does not produce any frequency or current fold-back. It is meant to protect
the high-side MOSFET from excessive current. Under some conditions, such as high input voltage, this current
limit may trip before the low-side protection. The peak value of this current limit varies with duty-cycle.
In FPWM mode, the inductor current is allowed to go negative. Should this current exceed INEG, the low-side
switch is turned off until the next clock cycle. This is used to protect the low-side switch from excessive negative
current. When the device is in AUTO mode, the negative current limit is increased to about 0 A; IZC. This allows
the device to operate in DCM.
8.3.4 Synchronizing Input
The internal clock of the LM53603 can be synchronized to a system clock through the SYNC input. This input
recognizes a valid high level as that ≥ 1.5 V, and a valid low as that ≤ 0.4 V. The frequency synchronization
signal should be in the range of 1.9 MHz to 2.3 MHz with a duty cycle of from 10% to 90%. The internal clock is
synced to the rising edge of the external clock. If this input is not used, it should be grounded. The maximum
voltage on this input is 5.5 V; and should not be allowed to float. See the Device Functional Modes section to
determine which modes are valid for synchronizing the clock.
8.3.5 Input Supply Current
The LM53603 is designed to have very low input supply current when regulating light loads. One way this is
achieved is by powering much of the internal circuitry from the output. The BIAS pin is the input to the LDO that
powers the majority of the control circuits. By connecting the BIAS input to the output of the regulator, this current
acts as a small load on the output. This current is reduced by the ratio of VOUT/VIN, just like any other load.
Another advantage of the LM53603 is that the feedback divider is integrated into the device. This allows the use
of much larger resistors than can be used externally; >> 100 kΩ. This results in much lower divider current than
is possible with external resistors. Equation 2 can be used to estimate the total input supply current when the
device is regulating with no external loads. The terms of the equation are as follows:
• IIN: Input supply current with no load.
• IQ: Device quiescent current, see Electrical Characteristics.
• IEN: Current into EN pin; see Electrical Characteristics.
• IB: Current into BIAS pin; see Electrical Characteristics.
• K: ≈ 0.9
IIN
14
IQ
IEN
VOUT
VIN ˜ K
§
˜ ¨¨ IB
©
VOUT ·
¸
RFB ¸¹
Submit Documentation Feedback
(2)
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
Feature Description (continued)
Equation 2 can be used as a guide to indicate how the various terms affect the input supply current. The
Application Curves show measured values for the input supply current for both 3.3-V and 5-V output voltage
versions.
8.3.6 UVLO and TSD
The LM53603 incorporates an input undervoltage lockout (UVLO) function. The device accepts an EN command
when the input voltage rises above about 3.64 V and shuts down when the input falls below about 3.3 V. See the
Electrical Characteristics table under VIN-operate for detailed specifications.
Thermal shutdown is provided to protect the device from excessive temperature. When the junction temperature
reaches about 162°C, the device shuts down; restart occurs at a temperature of about 144ºC.
8.4 Device Functional Modes
See Table 1 and the following paragraphs for a detailed description of the functional modes for the LM53603.
These modes are controlled by the FPWM input as shown in Table 1. This input can be controlled by any
compatible logic, and the mode changed while the regulator is operating. If it is desired to lock the mode for a
given application, the input can be either connected to ground, a logic supply, or the VCC pin, as desired. The
maximum input voltage on this pin is 5.5 V and it should not be allowed to float.
Table 1. Mode Selection
FPWM INPUT VOLTAGE
OPERATING MODE
> 1.5 V
Forced PWM: The regulator operates as a constant frequency, current mode, fullsynchronous converter for all loads; without diode emulation.
< 0.4 V
AUTO: The regulator moves between PFM and PWM as the load current changes, using
diode-emulation-mode to allow DCM (see the Glossary).
8.4.1 AUTO Mode
In AUTO mode the device moves between PWM and PFM as the load changes. At light loads the regulator
operates in PFM. At higher loads the mode changes to PWM. The load currents for which the devices moves
from PWM to PFM can be found in the Application Curves.
In PWM , the converter operates as a constant frequency, current mode, full synchronous converter using PWM
to regulate the output voltage. While operating in this mode the output voltage is regulated by switching at a
constant frequency and modulating the duty cycle to control the power to the load. This provides excellent line
and load regulation and low output voltage ripple. When in PWM, the converter synchronizes to any valid clock
signal on the SYNC input (see Dropout and Input Voltage Frequency Fold-Back).
In PFM the high-side FET is turned on in a burst of one or more cycles to provide energy to the load. The
frequency of these bursts is adjusted to regulate the output, while diode emulation is used to maximize efficiency.
This mode provides high light load efficiency by reducing the amount of input supply current required to regulate
the output voltage at small loads Glossary. This trades off very good light load efficiency for larger output voltage
ripple and variable switching frequency. Also, a small increase in the output voltage occurs in PFM. The actual
switching frequency and output voltage ripple depend on the input voltage, output voltage, and load. Typical
switching waveforms for PFM are shown in Figure 12. See the Application Curves for output voltage variation in
AUTO mode. The SYNC input is ignored during PFM operation.
A unique feature of this device, is that a minimum input voltage is required for the regulator to switch from PWM
to PFM at light load. This feature is a consequence of the advanced architecture employed to provide high
efficiency at light loads. Figure 13 indicates typical values of input voltage required to switch modes at no-load.
Also, once the regulator switches to PFM, at light load, it remains in that mode if the input voltage is reduced.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
15
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
SW, 5V/div
VOUT, 50mV/div
Iinductor, 500mA/div
10µs/div
2 ms/div
Figure 12. Typical PFM Switching Waveforms
8
3.3 V
5V
7.5
Input Voltage (V)
7
6.5
6
5.5
5
4.5
4
3.5
3
-60
-40
-20
0
20
40
60
Temperature (°C)
80
100
120
140
D023
Figure 13. Input Voltage for Mode Change
8.4.2 FPWM Mode
With a logic high on the FPWM input, the device is locked in PWM mode. This operation is maintained, even at
no-load, by allowing the inductor current to reverse its normal direction. This mode trades off reduced light load
efficiency for low output voltage ripple, tight output voltage regulation, and constant switching frequency. In this
mode, a negative current limit of INEG is imposed to prevent damage to the regulators low-side FET. When in
FPWM, the converter synchronizes to any valid clock signal on the SYNC input (see Dropout and Input Voltage
Frequency Fold-Back).
16
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
8.4.3 Dropout
One of the parameters that influences the dropout performance of a buck regulator is the minimum off-time. As
the input voltage is reduced, to near the output voltage, the off-time of the high-side switch starts to approach the
minimum value (see Timing Requirements). Beyond this point the switching may become erratic or the output
voltage falls out of regulation. To avoid this problem, the LM53603 automatically reduces the switching frequency
to increase the effective duty cycle. This results in two specifications regarding dropout voltage, as shown in the
System Characteristics table. One specification indicates when the switching frequency drops to 1.85 MHz;
avoiding the A.M. radio band. The other specification indicates when the output voltage has fallen to 1% of
nominal. See the Application Curves for typical values of dropout. The overall dropout characteristic for the 5-V
option, can be seen in Figure 14. The SYNC input is ignored during frequency fold-back in dropout.
5.2
Output Voltage (V)
5
4.8
4.6
4.4
1A
2A
3A
4.2
4
4
4.5
5
5.5
6
6.5
7
Input Voltage (V)
C003
Figure 14. Overall Dropout Characteristic
VOUT = 5V
8.4.4 Input Voltage Frequency Fold-Back
At higher input voltages the on-time of the high-side switch becomes small. When the minimum is reached (see
Timing Requirements), the switching may become erratic or the output voltage falls out of regulation. To avoid
this behavior, the LM53603 automatically reduces the switching frequency at input voltages above about 20 V
(see Application Curves). In this way the device avoids the minimum on-time restriction and maintains regulation
at abnormally high battery voltages. The SYNC input is ignored during frequency fold-back at high input voltages.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
17
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI's customers are
responsible for determining the suitability of components for their purposes. Customers
should validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LM53603 and LM53602 are step-down DC-DC converters, typically used to convert a higher DC voltage to a
lower DC voltage with a maximum output current of either 3 A or 2 A. The following design procedure can be
used to select components for the LM53603 or LM53602. Alternately, the WEBENCH® Design Tool may be used
to generate a complete design. This tool uses an iterative design procedure and has access to a comprehensive
database of components. This allows the tool to create an optimized design and allows the user to experiment
with various design options.
9.2 Typical Applications
9.2.1 Typical and Full-Featured Industrial Application Circuits
Figure 15 shows the minimum required application circuit for the fixed output voltage versions, while Figure 16
shows the connections for complete processor control of the LM53603. See these figures while following the
design procedures. Table 2 provides an example of typical design requirements.
L
VIN
6V to 36V
VIN
CIN
3x 10µF
10nF
LM53603
2.2 µH
EN
RESET
CBOOT
CBOOT
5V or 3.3V
3A
COUT
0.47 µF
VCC
SYNC
VOUT
SW
3x 22µF
FB
FPWM
CVCC
AGND
3.3 µF
PGND
RBIAS
BIAS
3Ÿ
CBIAS
0.1 µF
Copyright © 2016, Texas Instruments Incorporated
Figure 15. Typical Industrial Power Supply Schematic
18
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
Typical Applications (continued)
VIN
6V to 36V
CIN
10nF
3x 10µF
L
VIN
LM53603
SW
2.2 µH
EN
FPWM
µC
CBOOT
3.3V or 5V
3A
0.47 µF
3x 22µF
CBOOT
COUT
SYNC
RESET
VOUT
FB
VCC
100 kŸ
AGND
CVCC
PGND
RBIAS
BIAS
3.3 µF
3Ÿ
CBIAS
0.1 µF
Copyright © 2016, Texas Instruments Incorporated
Figure 16. Full-Featured Industrial Power Supply Schematic
9.2.1.1 Design Parameters
There are a few design parameters to take into account. Most of those choices decide which version of the
device to use. The desired output current steers the designer toward a LM53602 type or LM53603 type part. If
the output voltage is 3.3 V or 5 V, a fixed output version of the device can be used. Any other voltage level within
the tolerance of the part can be achieved by using an adjustable version of the device. Most but not all
parameters are independent of the of the IC choice. The output filter components (inductor and output
capacitors) might vary with the choice of output voltage, especially for output voltages higher than 5 V. See
Detailed Design Procedure for help in choosing these components.
Table 2. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage
12 V
Output voltage
5V
Maximum output current
3A
9.2.1.2 Detailed Design Procedure
The following detailed design procedure applies to Figure 15, Figure 16, and Figure 45.
9.2.1.2.1 Setting the Output Voltage
For the fixed output voltage versions, the FB input is connected directly to the output voltage node. Preferably,
near the top of the output capacitor. If the feed-back point is located further away from the output capacitors (that
is, remote sensing), then a small 100-nF capacitor may be needed at the sensing point.
For output voltages other than 5 V or 3.3 V, a feedback divider is required. For the ADJ version of the device, the
regulator holds the FB pin at 1 V. The range of adjustable output voltage can be found in the Recommended
Operating Conditions. Equation 3 can be used to determine RFBB for a desired output voltage and a given RFBT.
Usually RFBT is limited to a maximum value of 100 kΩ.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
19
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
RFBB
www.ti.com
ª
º
1V
RFBT ˜ «
»
¬ VOUT 1V ¼
(3)
In addition, a feed-forward capacitor CFF may be required to optimize the transient response. For output voltages
greater than 6 V, the WEBENCH Design Tool can be used to optimize the design. Recommended CFF values for
some cases are given in the table below. It is important to note that these values provide a first approximation
only and need to be verified for each application by the designer.
Table 3. Recommended CFFcapacitors
VOUT
(1)
COUT (nominal)
(1)
L
RFBT
RFBB
3.2V
44µF
2.2µH
69.8kΩ
31.6kΩ
CFF
33pF
3.2V
110µF
2.2µH
69.8kΩ
31.6kΩ
120pF
5.1V
44µF
2.2µH
80.6kΩ
19.6kΩ
33pF
5.1V
110µF
2.2µH
80.6kΩ
19.6kΩ
220pF
8V
66µF
4.7µH
86.6kΩ
12.4kΩ
120pF
8V
100µF
4.7µH
86.6kΩ
12.4kΩ
220pF
10V
66µF
4.7µH
90.9kΩ
10.0kΩ
120pF
16V X7R capacitors used : C3225X7R1C226M250AC (TDK)
9.2.1.2.2 Output Capacitors
The LM53603 is designed to work with low-ESR ceramic capacitors. The effective value of these capacitors is
defined as the actual capacitance under voltage bias and temperature. All ceramic capacitors have a large
voltage coefficient, in addition to normal tolerances and temperature coefficients. Under DC bias, the capacitance
value drops considerably. Larger case sizes or higher voltage capacitors are better in this regard. To help
mitigate these effects, multiple small capacitors can be used in parallel to bring the minimum effective
capacitance up to the desired value. This can also ease the RMS current requirements on a single capacitor.
Table 4 shows the nominal and minimum values of total output capacitance recommended for the LM53603. The
values shown also provide a starting point for other output voltages, when using the ADJ option. Also shown are
the measured values of effective capacitance for the indicated capacitor. More output capacitance can be used
to improve transient performance and reduce output voltage ripple.
In practice, the output capacitor has the most influence on the transient response and loop phase margin. Load
transient testing and Bode plots are the best way to validate any given design, and should always be completed
before the application goes into production. A careful study of temperature and bias voltage variation of any
candidate ceramic capacitor should be made to ensure that the minimum value of effective capacitance is
provided. The best way to obtain an optimum design is to use the Texas Instruments WEBENCH Design Tool.
In ADJ applications the feed-forward capacitor, CFF, provides another degree of freedom when stabilizing and
optimizing the design. Application report Optimizing Transient Response of Internally Compensated dc-dc
Converters With Feedforward Capacitor (SLVA289) should prove helpful when adjusting the feed-forward
capacitor.
In addition to the capacitance shown in Table 4, a small ceramic capacitor placed on the output can help to
reduce high frequency noise. Small case size ceramic capacitors in the range of 1 nF to 100 nF can be very
helpful in reducing spikes on the output caused by inductor parasitics.
The maximum value of total output capacitance should be limited to between 300 µF and 400 µF. Large values
of output capacitance can prevent the regulator from starting-up correctly and adversely effect the loop stability. If
values in the range given above, or greater, are to be used, then a careful study of start-up at full load and loop
stability must be performed.
20
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
Table 4. Recommended Output Capacitors
OUTPUT
VOLTAGE
(1)
(2)
NOMINAL OUTPUT CAPACITANCE
MINIMUM OUTPUT CAPACITANCE
PART NUMBER
(MANUFACTURER)
RATED
CAPACITANCE
MEASURED
CAPACITANCE (1)
RATED
CAPACITANCE
MEASURED
CAPACITANCE (1)
3.3 V
3 × 22 µF
63 µF
2 × 22 µF
42 µF
C3225X7R1C226M250AC (TDK)
5V
3 × 22 µF
60 µF
2 × 22 µF
40 µF
C3225X7R1C226M250AC (TDK)
6V
3 × 22 µF
59 µF
2 × 22 µF
39 µF
C3225X7R1C226M250AC (TDK)
10 V (2)
3 × 22 µF
48 µF
2 × 22 µF
32 µF
C3225X7R1C226M250AC (TDK)
Measured at indicated VOUT at 25°C.
The following components were used: CFF = 47 pF, RFBT = 100 kΩ, RFBB = 11 kΩ, L = 4. 7 µH.
9.2.1.2.3 Input Capacitors
The ceramic input capacitors provide a low impedance source to the regulator in addition to supplying ripple
current and isolating switching noise from other circuits. Table 5 shows the nominal and minimum values of total
input capacitance recommenced for the LM53603. Also shown are the measured values of effective capacitance
for the indicated capacitor. In addition, small high frequency bypass capacitors connected directly between the
VIN and PGND pins are very helpful in reducing noise spikes and aid in reducing conducted EMI. TI
recommends that a small case size 10-nF ceramic capacitor be placed across the input, as close as possible to
the device (see Figure 47). Additional high frequency capacitors can be used to help manage conducted EMI or
voltage spike issues that may be encountered.
Table 5. Recommended Input Capacitors
NOMINAL INPUT CAPACITANCE
RATED
CAPACITANCE
3 x 10 µF
(1)
MEASURED
CAPACITANCE
MINIMUM INPUT CAPACITANCE
(1)
22.5 µF
RATED
CAPACITANCE
MEASURED
CAPACITANCE (1)
2 × 10 µF
15 µF
PART NUMBER (MANUFACTURER)
CL32B106KBJNNNE (Samsung)
Measured at 14 V and 25°C.
Many times it is desirable to use an electrolytic capacitor on the input, in parallel with the ceramics. This is
especially true if longs leads or traces are used to connect the input supply to the regulator. The moderate ESR
of this capacitor can help damp any ringing on the input supply caused by long power leads. The use of this
additional capacitor also helps with voltage dips caused by input supplies with unusually high impedance.
Most of the input switching current passes through the ceramic input capacitor(s). The approximate RMS value of
this current can be calculated from Equation 4 and should be checked against the manufacturers' maximum
ratings.
IRMS #
IOUT
2
(4)
9.2.1.2.4 Inductor
The LM53603 and LM53602 are optimized for a nominal inductance of 2.2 µH for the 5-V and 3.3-V versions.
This gives a ripple current that is approximately 20% to 30% of the full load current of 3 A. For output voltages
greater than 5 V, a proportionally larger inductor can be used. This keeps the ratio of inductor current slope to
internal compensating slope constant.
The most important inductor parameters are saturation current and parasitic resistance. Inductors with a
saturation current of between 5 A and 6 A are appropriate for most applications, when using the LM53603. For
the LM53602, inductors with a saturation current of between 4 A and 5 A are appropriate. Of course the inductor
parasitic resistance should be as low as possible to reduce losses at heavy loads. Table 6 gives a list of several
possible inductors that can be used with the LM53603.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
21
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
Table 6. Recommenced Inductors
MANUFACTURER
PART NUMBER
SATURATION
CURRENT
DC RESISTANCE
Würth
7440650022
6A
15 mΩ
Coilcraft
DO3316T-222MLB
7.8 A
11 mΩ
Coiltronics
MPI4040R3-2R2-R
7.9 A
48 mΩ
Vishay
IHLP2525CZER2R2M01
14 A
18 mΩ
Vishay
IHLP2525BDER2R2M01
14 A
28 mΩ
Coilcraft
XAL6030-222ME
16 A
13 mΩ
9.2.1.2.5 VCC
The VCC pin is the output of the internal LDO, used to supply the control circuits of the LM53603. This output
requires a 3.3-µF to 4.7-µF, ceramic capacitor connected from VCC to GND for proper operation. An X7R device
with a rating of 10 V is highly recommended. In general this output should not be loaded with any external
circuitry. However, it can be used to supply a logic level to the FPWM input, or for the pullup resistor used with
the RESET output (see Figure 16). The nominal output of the LDO is 3.15 V.
9.2.1.2.6 BIAS
The BIAS pin is the input to the internal LDO. As mentioned in Input Supply Current, this input is connected to
VOUT to provide the lowest possible supply current at light loads. Because this input is connected directly to the
output, it should be protected from negative voltage transients. Such transients may occur when the output is
shorted at the end of a long PCB trace or cable. If this is likely, in a given application, then a small resistor
should be placed in series between the BIAS input and VOUT, as shown in Figure 15. The resistor should be
sized to limit the current out of the BIAS pin to <100 mA. Values in the range of 2 Ω to 5 Ω are usually sufficient.
Values greater than 5 Ω are not recommended. As a rough estimate, assume that the full negative transient
appears across RBIAS and design for a current of < 100 mA. In severe cases, a Schottky diode can be placed in
parallel with the output to limit the transient voltage and current.
9.2.1.2.7 CBOOT
The LM53603 requires a boot-strap capacitor between the CBOOT pin and the SW pin. This capacitor stores
energy that is used to supply the gate drivers for the power MOSFETs. A ceramic capacitor of 0.47 µF, ≥ 6.3 V is
required. A 10-V rated capacitor or higher is highly recommended.
9.2.1.2.8 Maximum Ambient Temperature
As with any power conversion device, the LM53603 dissipates internal power while operating. The effect of this
power dissipation is to raise the internal temperature of the converter, above ambient. The internal die
temperature (TJ) is a function of the ambient temperature, the power loss and the effective thermal resistance,
RθJA of the device and PCB combination. The maximum internal die temperature for the LM53603 is 150°C, thus
establishing a limit on the maximum device power dissipation and therefore load current at high ambient
temperatures. Equation 5 shows the relationships between the important parameters.
IOUT
TJ TA
K
1
˜
˜
R TJA
1 K VOUT
(5)
It is easy to see that larger ambient temperatures (TA) and larger values of RθJA reduce the maximum available
output current. As stated in Semiconductor and IC Package Thermal Metrics, the values given in the Thermal
Information table are not valid for design purposes and must not be used to estimate the thermal performance of
the application. The values reported in that table were measured under a specific set of conditions that are never
obtained in an actual application. The effective RθJA is a critical parameter and depends on many factors such as
power dissipation, air temperature, PCB area, copper heat sink area, number of thermal vias under the package,
air flow, and adjacent component placement. The LM53603 uses an advanced package with a heat spreading
pad (EP) on the bottom. This must be soldered directly to the PCB copper ground plane to provide an effective
heat sink, as well as a proper electrical connection. The resources in Ground and Thermal Plane Considerations
can be used as a guide to optimal thermal PCB design and estimating RθJA for a given application environment.
A typical example of RθJA versus copper board area is shown in Figure 17. The copper area in this graph is that
22
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
for each layer of a four-layer board; the inner layers are 1 oz. (35 µm), while the outer layers are 2 oz. (70 µm). A
typical curve of maximum load current versus ambient temperature, for both the LM53603 and LM53602, is
shown in Figure 18. This data was taken with the device soldered to a PCB with an RθJA of about 17°C/W and an
input voltage of 12 V. It must be remembered that the data shown in these graphs are for illustration only and the
actual performance in any given application depends on all of the factors mentioned above.
50
45
LM53603,
3.3V
LM53603,
5V
LM53602,
3.3V
LM53602,
5V
3.0
40
2.5
Output Current (A)
Theta JA (C/W)
3.5
0.5 W
1W
2W
35
30
25
2.0
1.5
1.0
20
0
500
1000
1500
2000
Board Area (mm2)
2500
3000
0.5
D024
0.0
80
90
100
110
120
130
140
150
Ambient Temperature (C)
C006
Figure 17. RθJA vs Copper Board Area
Figure 18. Maximum Output Current vs Ambient
Temperature
RθJA = 17°C/W, VIN = 12 V
3
3
2.5
Power Dissipation (W)
Power Dissipation (W)
2.5
7 Vin
12 Vin
18 Vin
2
1.5
1
2
1.5
1
0.5
0.5
0
0.5
7 Vin
12 Vin
18 Vin
1
1.5
2
Output Current (A)
2.5
3
0
0.5
D032
Figure 19. IC Power Dissipation vs Output Current for 3.3V output
1
1.5
2
Output Current (A)
2.5
3
D033
Figure 20. IC Power Dissipation vs Output Current for 5-V
output
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
23
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
9.2.1.3 Application Curves
The following characteristics apply only to the circuit of Figure 15. These parameters are not tested and
represent typical performance only. Unless otherwise stated, the following conditions apply: VIN = 12 V, TA =
25°C.
100%
90%
80%
5.08
12 VIN
18 VIN
7 VIN
5.06
Output Voltage (V)
70%
Efficiency
60%
50%
40%
30%
5.05
5.04
5.03
5.02
5.01
5
20%
4.99
10%
4.98
0
0.00001
7V
12 V
18 V
36 V
5.07
4.97
0.0001
0.001
0.01
Output Current (A)
0.1
1
3
0
VOUT = 5 V
AUTO
Inductor = XAL6030-222ME
1.5
2
Output Current (A)
2.5
3
3.5
D008
AUTO
Figure 22. Load and Line Regulation
0.35
60
-40°C
25°C
105°C
UP
DN
0.3
Output Current (A)
50
Supply Current (µA)
1
VOUT = 5 V
Figure 21. Efficiency
40
30
20
10
0.25
0.2
0.15
0.1
0.05
0
0
0
5
10
15
20
25
Input Voltage (V)
VOUT = 5 V
30
35
0
40
2
4
6
D014
AUTO
IOUT = 0 A
8
10
12
Input Voltage (V)
14
16
18
20
D013
VOUT = 5 V
Figure 23. Input Supply Current
Figure 24. Load Current for Mode Change
1
3
-40°C
27°C
105°C
0.9
-40°C
27°C
105°C
2.5
Drop-out Voltage (V)
0.8
Drop-out Voltage (V)
0.5
D028
0.7
0.6
0.5
0.4
0.3
0.2
2
1.5
1
0.5
0.1
0
0
0
0.5
1
1.5
2
Output Current (A)
2.5
3
0
0.5
D011
VOUT = 5 V
1
1.5
2
Output Current (A)
2.5
3
3.5
D012
VOUT = 5 V
Figure 25. Dropout for –1% Regulation
24
3.5
Figure 26. Dropout for ≥ 1.85 MHz
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
The following characteristics apply only to the circuit of Figure 15. These parameters are not tested and
represent typical performance only. Unless otherwise stated, the following conditions apply: VIN = 12 V, TA =
25°C.
10000000
100000
0A
2A
3A
2000000
Frequency (Hz)
Switching Frequency (Hz)
1000000
2500000
6V
12 V
18 V
36 V
10000
1000
1500000
1000000
100
500000
10
1
1E-6
0
1E-5
VOUT = 5 V
0.0001
0.001
0.01
Output Current (A)
0.1
1
10
0
5
D031
AUTO
VOUT = 5 V
Figure 27. Switching Frequency vs Load Current
10
15
20
25
Input Voltage (V)
30
35
40
D026
FPWM
Figure 28. Switching Frequency vs Input Voltage
EN, 3V/div
VOUT, 2V/div
VOUT, 100mV/div
RESET, 4V/div
Iinductor, 1A/div
Output Current, 1A/div
50µs/div
1ms/div
VOUT = 5 V
IOUT = 0 A
AUTO
VOUT = 5 V
IOUT = 0 A to 3 A, TR = TF = 1 µs
AUTO
Figure 30. Load Transients
Figure 29. Start-Up
FPWM, 4v/div
VOUT, 100mV/div
VOUT, 100mV/div
Iinductor, 1A/div
Output Current, 1A/div
2ms/div
50µs/div
VOUT = 5 V
IOUT = 0 A to 3 A, TR = TF = 1 µs
Figure 31. Load Transient
FPWM
VOUT = 5 V
IOUT = 1 mA
Figure 32. Mode Change Transient
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
25
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
The following characteristics apply only to the circuit of Figure 15. These parameters are not tested and
represent typical performance only. Unless otherwise stated, the following conditions apply: VIN = 12 V, TA =
25°C.
100%
90%
80%
3.36
12 VIN
18 VIN
7 VIN
3.34
Output Voltage (V)
Efficiency
70%
60%
50%
40%
30%
3.33
3.32
3.31
3.3
20%
3.29
10%
3.28
0
0.00001
6V
12 V
18 V
36 V
3.35
3.27
0.0001
0.001
0.01
Output Current (A)
0.1
1
3
0
0.5
VOUT = 3.3 V
AUTO
Inductor = XAL6030-222ME
VOUT = 3.3 V
1.5
2
Output Current (A)
2.5
3
3.5
D016
AUTO
Figure 34. Load and Line Regulation
45
0.45
40
0.4
35
0.35
Output Current (A)
Supply Current (µA)
Figure 33. Efficiency
30
25
20
15
10
UP
DN
0.3
0.25
0.2
0.15
0.1
-40°C
25°C
105°C
5
0.05
0
0
0
5
10
15
20
25
Input Voltage (V)
VOUT = 3.3 V
30
35
0
40
2
4
6
D022
AUTO
IOUT = 0 A
8
10
12
Input Voltage (V)
14
16
18
20
D021
VOUT = 3.3 V
Figure 35. Input Supply Current
Figure 36. Load Current for Mode Change
1
2.5
-40°C
27°C
105°C
0.9
-40°C
27°C
105°C
2
Drop-out Voltage (V)
0.8
Drop-out Voltage (V)
1
D029
0.7
0.6
0.5
0.4
0.3
0.2
1.5
1
0.5
0.1
0
0
0
0.5
1
1.5
2
Output Current (A)
2.5
3
0
0.5
1
D019
VOUT = 3.3 V
1.5
2
Output Current (A)
2.5
3
3.5
D020
VOUT = 3.3 V
Figure 37. Dropout for –1% Regulation
26
3.5
Figure 38. Dropout for ≥ 1.85 MHz
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
The following characteristics apply only to the circuit of Figure 15. These parameters are not tested and
represent typical performance only. Unless otherwise stated, the following conditions apply: VIN = 12 V, TA =
25°C.
10000000
2500000
6V
12 V
18 V
36 V
100000
0A
2A
3A
2000000
Frequency (Hz)
Switching Frequency (Hz)
1000000
10000
1000
1500000
1000000
100
500000
10
1
1E-6
0
1E-5
0.0001
0.001
0.01
Output Current (A)
VOUT = 3.3 V
0.1
1
0
10
5
D030
AUTO
VOUT = 3.3 V
Figure 39. Switching Frequency vs Load Current
10
15
20
25
Input Voltage (V)
30
35
40
D027
FPWM
Figure 40. Switching Frequency vs Input Voltage
EN, 3V/div
VOUT, 100mV/div
VOUT, 2V/div
RESET, 4V/div
Iinductor, 1A/div
Output Current, 1A/div
1ms/div
VOUT = 3.3 V
50µs/div
AUTO
IOUT = 0 A
VOUT = 3.3 V
IOUT = 0 A to 3 A, TR = TF = 1 µs
Figure 41. Start-Up
AUTO
Figure 42. Load Transient
FPWM, 4v/div
VOUT, 100mV/div
VOUT, 100mV/div
Iinductor, 1A/div
Output Current, 1A/div
50µs/div
VOUT = 3.3 V
2ms/div
IOUT = 0 A to 3 A, TR = TF = 1 µs
Figure 43. Load Transient
FPWM
VOUT = 3.3 V
IOUT = 1 mA
Figure 44. Mode Change Transient
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
27
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
9.3 Typical Adjustable Industrial Application Circuit
Figure 45 shows a typical example of a design with an output voltage of 10 V; while Table 7 gives typical design
parameters. See Detailed Design Procedure for the design procedure.
L
10nF
VIN
LM53603
VIN
12V to 36V
CIN
4.7 µH
EN
3x 10µF
RFBT
CBOOT
100 kŸ
0.47 µF
VCC
CFF
47 pF
SYNC
FPWM
COUT
3x 22µF
FB
AGND
3.3 µF
10V @ 3A
CBOOT
RESET
CVCC
VOUT
SW
RFBB
PGND
11 kŸ
BIAS
RBIAS
3Ÿ
CBIAS
0.1 µF
Copyright © 2016, Texas Instruments Incorporated
Figure 45. Typical Adjustable Output Industrial Power Supply Schematic
CD/DVD/Blu-ray Disc™ Motor Drive Applications
VOUT = 10 V
9.3.1 Design Parameters for Typical Adjustable Output Industrial Power Supply
There are a few design parameters to take into account. Most of those choices decide which version of the
device to use. The desired output current steers the designer toward a LM53602 type or LM53603 type part.
Most but not all parameters are independent of the of the IC choice. The output filter components (inductor and
output capacitors) might vary with the choice of output voltage, especially for output voltages higher than 5 V.
Refer to Detailed Design Procedure for details on choosing the components for the application.
Table 7. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Input Voltage
12 V
Output Voltage
10 V
Maximum Output Current
3A
9.4 Do's and Don't's
•
•
•
•
•
•
•
•
28
Don't: Exceed the Absolute Maximum Ratings.
Don't: Exceed the ESD Ratings.
Don't: Exceed the Recommended Operating Conditions.
Don't: Allow the EN, FPWM or SYNC input to float.
Don't: Allow the output voltage to exceed the input voltage, nor go below ground.
Don't: Use the thermal data given in the Thermal Information table to design your application.
Do: Follow all of the guidelines and suggestions found in this data sheet, before committing your design to
production. TI Application Engineers are ready to help critique your design and PCB layout to help make your
project a success.
Do: Refer to the helpful documents found in Layout Guidelines and Ground and Thermal Plane
Considerations.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
10 Power Supply Recommendations
The characteristics of the input supply must be compatible with the Absolute Maximum Ratings and
Recommended Operating Conditions found in this data sheet. In addition, the input supply must be capable of
delivering the required input current to the loaded regulator. The average input current can be estimated with
Equation 6, where η is the efficiency.
IIN
VOUT ˜ IOUT
VIN ˜ K
(6)
If the regulator is connected to the input supply through long wires or PCB traces, take special care to achieve
good performance. The parasitic inductance and resistance of the input cables can have an adverse effect on
the operation of the regulator. The parasitic inductance, in combination with the low-ESR ceramic input
capacitors, can form an under-damped resonant circuit. This circuit may cause overvoltage transients at the VIN
pin, each time the input supply is cycled on and off. The parasitic resistance causes the voltage at the VIN pin to
dip when the load on the regulator is switched on, or exhibits a transient. If the regulator is operating close to the
minimum input voltage, this dip may cause the device to shutdown or reset. The best way to solve these kinds of
issues is to reduce the distance from the input supply to the regulator or use an aluminum or tantalum input
capacitor in parallel with the ceramics. The moderate ESR of these types of capacitors helps to damp the input
resonant circuit and reduce any voltage overshoots. A value in the range of 20 µF to 100 µF is usually sufficient
to provide input damping and help to hold the input voltage steady during large load transients.
Sometimes, for other system considerations, an input filter is used in front of the regulator. This can lead to
instability, as well as some of the effects mentioned above, unless it is designed carefully. The user guide Simple
Success with Conducted EMI for DC-DC Converters (SNVA489), provides helpful suggestions when designing
an input filter for any switching regulator
In some cases a Transient Voltage Suppressor (TVS) is used on the input of regulators. One class of this device
has a snap-back V-I characteristic (thyristor type). The use of a device with this type of characteristic is not
recommend. When the TVS fires, the clamping voltage drops to a very low value. If this holding voltage is less
than the output voltage of the regulator, the output capacitors is discharged through the regulator back to the
input. This uncontrolled current flow could damage the regulator.
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
29
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
11 Layout
11.1 Layout Guidelines
The PCB layout of any DC-DC converter is critical to the optimal performance of the design. Bad PCB layout can
disrupt the operation of an otherwise good schematic design. Even if the converter regulates correctly, bad PCB
layout can mean the difference between a robust design and one that cannot be mass produced. Furthermore,
the EMI performance of the regulator is dependent on the PCB layout, to a great extent. In a buck converter, the
most critical PCB feature is the loop formed by the input capacitor and power ground, as shown in Figure 46.
This loop carries fast transient currents that can cause large transient voltages when reacting with the trace
inductance. These unwanted transient voltages disrupt the proper operation of the converter. Because of this, the
traces in this loop should be wide and short, and the loop area as small as possible to reduce the parasitic
inductance. Figure 47 shows a recommended layout for the critical components of the LM53603. This PCB
layout is a good guide for any specific application. The following important guidelines must also be followed:
1. Place the input capacitor(s) CIN as close as possible to the VIN and PGND terminals. VIN and GND
are on the same side of the device, simplifying the input capacitor placement.
2. Place bypass capacitors for VCC and BIAS close to their respective pins. These components must be
placed close to the device and routed with short and wide traces to the pins and ground. The trace from
BIAS to VOUT should be ≥10 mils wide. BIAS and VCC capacitors must be place within 4 mm of the BIAS
and VCC pin (160 mils) .
3. Use wide traces for the CBOOT capacitor. CBOOT must be placed close to the device with short and wide
traces to the CBOOT and SW pins.
4. Place the feedback divider as close as possible to the FB pin on the device. If a feedback divider and
CFF are used, they must be close to the device while the length of the trace from VOUT to the divider can be
somewhat longer. However, this latter trace must not be routed near any noise sources that can capacitively
couple to the FB input.
5. Use at least one ground plane in one of the middle layers. This plane acts as a noise shield and also act
as a heat dissipation path.
6. Connect the EP pad to the GND plane. This pad acts as a heat sink connection and a ground connection
for the regulator. It must be solidly connected to a ground plane. The integrity of this connection has a direct
bearing on the effective RθJA.
7. Provide wide paths for VIN, VOUT and GND. Making these paths as wide as possible reduces any voltage
drops on the input or output paths of the converter and maximizes efficiency.
8. Provide enough PCB area for proper heat sinking. As stated in the Maximum Ambient Temperature
section, enough copper area must be used to ensures a low RθJA, commensurate with the maximum load
current and ambient temperature. The top and bottom PCB layers must be made with two ounce copper; and
no less than one ounce. Use an array of heat sinking vias to connect the exposed pad (EP) to the ground
plane on the bottom PCB layer. If the PCB has multiple copper layers (recommended), these thermal vias
can also be connected to the inner layer heat-spreading ground planes.
9. Keep switch area small. The copper area connecting the SW pin to the inductor must be kept as short and
wide as possible. At the same time the total area of this node must be minimized to help mitigate radiated
EMI.
10. These resources provide additional important guidelines:
– AN-1149 Layout Guidelines for Switching Power Supplies (SNVA021)
– AN-1229 Simple Switcher PCB Layout Guidelines (SNVA054)
– Constructing Your Power Supply- Layout Considerations (SLUP230)
– Low Radiated EMI Layout Made SIMPLE with LM4360x and LM4600x (SNVA721)
30
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
Layout Guidelines (continued)
VIN
CIN
SW
GND
Figure 46. Current Loops With Fast Transients
11.1.1 Ground and Thermal Plane Considerations
As mentioned in the Layout Guidelines, TI recommends using one of the middle layers as a solid ground plane.
A ground plane provides shielding for sensitive circuits and traces. It also provides a quiet reference potential for
the control circuitry. The AGND and PGND pins must be connected to the ground plane using vias right next to
the bypass capacitors. PGND pins are connected to the source of the internal low-side MOSFET switch. They
must be connected directly to the grounds of the input and output capacitors. The PGND net contains noise at
the switching frequency and may bounce due to load variations. The PGND trace, as well as PVIN and SW
traces, must be constrained to one side of the ground plane. The other side of the ground plane contains much
less noise and must be used for sensitive routes.
TI recommends providing adequate device heat sinking by using the exposed pad (EP) of the IC as the primary
thermal path. Use a minimum 4 × 4 array of 10-mil thermal vias to connect the EP to the system ground plane for
heat sinking. The vias must be evenly distributed under the exposed pad. Use as much copper as possible for
system ground plane on the top and bottom layers for the best heat dissipation. TI recommends using a fourlayer board with the copper thickness, starting from the top, as: 2 oz. / 1 oz. / 1 oz. / 2 oz. A four-layer board with
enough copper thickness and proper layout provides low current conduction impedance, proper shielding and
lower thermal resistance.
These resources provide additional important guidelines for thermal PCB design:
• AN-2020 Thermal Design By Insight, Not Hindsight (SNVA419)
• AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Pad Packages (SNVA183)
• Semiconductor and IC Package Thermal Metrics (SPRA953)
• Thermal Design made Simple with LM43603 and LM43602 (SNVA719)
• PowerPAD™ Thermally Enhanced Package (SLMA002)
• PowerPAD Made Easy (SLMA004)
• Using New Thermal Metrics (SBVA025)
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
31
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
11.2 Layout Example
Bottom Trace
VIA to Ground Plane
GND
HEATSINK
Top Trace
VOUT
INDUCTOR
COUT
COUT
CIN
CIN
GND
COUT
CBOOT
Rbias
CIN
VIN
CVCC
CBIAS
EN
SYNC
GND
HEATSINK
RFBT
RFBB
RESET
GND
HEATSINK
FPWM
Figure 47. PCB Layout Example
32
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
LM53602, LM53603
www.ti.com
SNVSAR0 – NOVEMBER 2016
12 Device and Documentation Support
12.1 Device Support
12.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
12.1.2 Developmental Support
For developmental support, see the following tools:
• High Density Efficient Solution for Main Aux as well as Back up Aux Power in Drones
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections
• 15W Synchronous Buck Regulator with Integrated FETs Reference Design
• System Level reference design for 30W ADAS system with required Automotive Protections
• 15-W System-Level Power Reference Design for Automotive Body Control Module
12.2 Documentation Support
12.2.1 Related Documentation
For related documentation see the following:
• Using New Thermal Metrics (SBVA025).
• Optimizing Transient Response of Internally Compensated dc-dc Converters With Feedforward Capacitor
(SLVA289).
• Simple Success with Conducted EMI for DC-DC Converters (SNVA489).
• AN-1149 Layout Guidelines for Switching Power Supplies (SNVA021).
• AN-1229 Simple Switcher PCB Layout Guidelines (SNVA054).
• Constructing Your Power Supply- Layout Considerations (SLUP230).
• Low Radiated EMI Layout Made SIMPLE with LM4360x and LM4600x (SNVA721).
• AN-2020 Thermal Design By Insight, Not Hindsight (SNVA419).
• AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Pad Packages (SNVA183).
• Semiconductor and IC Package Thermal Metrics (SPRA953).
• Thermal Design made Simple with LM43603 and LM43602 (SNVA719).
• PowerPAD™ Thermally Enhanced Package (SLMA002).
• PowerPAD Made Easy (SLMA004).
• Using New Thermal Metrics (SBVA025).
12.3 Related Links
Table 8 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to sample or buy.
Table 8. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LM53602
Click here
Click here
Click here
Click here
Click here
LM53603
Click here
Click here
Click here
Click here
Click here
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
33
LM53602, LM53603
SNVSAR0 – NOVEMBER 2016
www.ti.com
12.4 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.5 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.6 Trademarks
PowerPAD, E2E are trademarks of Texas Instruments.
WEBENCH is a registered trademark of Texas Instruments.
Blu-ray Disc is a trademark of Blu-ray Disk Association.
All other trademarks are the property of their respective owners.
12.7 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.8 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
34
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Product Folder Links: LM53602 LM53603
PACKAGE OPTION ADDENDUM
www.ti.com
23-Nov-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM53602AMPWPR
PREVIEW
HTSSOP
PWP
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 125
L53602A
LM53602AMPWPT
PREVIEW
HTSSOP
PWP
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 125
L53602A
LM53603AMPWPR
PREVIEW
HTSSOP
PWP
16
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 125
L53603A
LM53603AMPWPT
PREVIEW
HTSSOP
PWP
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 125
L53603A
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
23-Nov-2016
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE OUTLINE
PWP0016D
PowerPAD TM TSSOP - 1.2 mm max height
SCALE 2.250
PLASTIC SMALL OUTLINE
6.6
TYP
6.2
PIN 1 ID AREA
A
14X 0.65
16
1
5.1
4.9
NOTE 3
2X
4.55
8
9
B
4.5
4.3
16X
0.30
0.19
0.1
0.1 C
C A B
SEATING PLANE
C
(0.15) TYP
SEE DETAIL A
2X (0.95)
4X (0.3)
NOTE 5
4X 0.18 MAX
NOTE 5
0.25
GAGE PLANE
1.2 MAX
3.40
2.68
0 -8
THERMAL
PAD
0.75
0.50
0.15
0.05
DETAIL A
TYPICAL
2.48
1.75
4223219/A 08/2016
PowerPAD is a trademark of Texas Instruments.
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. Reference JEDEC registration MO-153.
5. Features may differ and may not be present.
www.ti.com
EXAMPLE BOARD LAYOUT
PWP0016D
PowerPAD TM TSSOP - 1.2 mm max height
PLASTIC SMALL OUTLINE
(3.4)
NOTE 9
SOLDER MASK
DEFINED PAD
(2.48)
16X (1.5)
SYMM
SEE DETAILS
1
16
16X (0.45)
( 0.2) TYP
VIA
(3.4)
SYMM
(0.65) TYP
14X (0.65)
(5)
NOTE 9
(1.3 TYP)
8
9
(R0.05) TYP
(1.1 TYP)
METAL COVERED
BY SOLDER MASK
(5.8)
LAND PATTERN EXAMPLE
SCALE:10X
SOLDER MASK
OPENING
METAL
METAL UNDER
SOLDER MASK
SOLDER MASK
OPENING
0.05 MIN
AROUND
0.05 MAX
AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4223219/A 08/2016
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
8. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
numbers SLMA002 (www.ti.com/lit/slma002) and SLMA004 (www.ti.com/lit/slma004).
9. Size of metal pad may vary due to creepage requirement.
www.ti.com
EXAMPLE STENCIL DESIGN
PWP0016D
PowerPAD TM TSSOP - 1.2 mm max height
PLASTIC SMALL OUTLINE
(2.48)
BASED ON
0.125 THICK
STENCIL
16X (1.5)
(R0.05) TYP
1
16
16X (0.45)
(3.4)
BASED ON
0.125 THICK
STENCIL
SYMM
14X (0.65)
8
9
SYMM
METAL COVERED
BY SOLDER MASK
(5.8)
SEE TABLE FOR
DIFFERENT OPENINGS
FOR OTHER STENCIL
THICKNESSES
SOLDER PASTE EXAMPLE
EXPOSED PAD
100% PRINTED SOLDER COVERAGE BY AREA
SCALE:10X
STENCIL
THICKNESS
SOLDER STENCIL
OPENING
0.1
0.125
0.15
0.175
2.77 X 3.8
2.48 X 3.4 (SHOWN)
2.26 X 3.1
2.1 X 2.87
4223219/A 08/2016
NOTES: (continued)
10. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
11. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated