ON MC10E137 5v ecl 8â bit ripple counter Datasheet

MC10E137, MC100E137
5 V ECL 8‐Bit Ripple Counter
Description
The MC10E/100E137 is a very high speed binary ripple counter. The
two least significant bits were designed with very fast edge rates while
the more significant bits maintain standard ECLinPS™ output edge
rates. This allows the counter to operate at very high frequencies while
maintaining a moderate power dissipation level.
The device is ideally suited for multiple frequency clock generation
as well as a counter in a high performance ATE time measurement
board.
Both asynchronous and synchronous enables are available to
maximize the device’s flexibility for various applications. The
asynchronous enable input, A_Start, when asserted enables the counter
while overriding any synchronous enable signals. The E137 features
XORed enable inputs, EN1 and EN2, which are synchronous to the
CLK input. When only one synchronous enable is asserted the counter
becomes disabled on the next CLK transition; all outputs remain in the
previous state poised for the other synchronous enable or A_Start to be
asserted to re-enable the counter. Asserting both synchronous enables
causes the counter to become enabled on the next transition of the CLK.
If EN1 (or EN2) and CLK edges are coincident, sufficient delay has
been inserted in the CLK path (to compensate for the XOR gate delay
and the internal D-flip flop setup time) to insure that the synchronous
enable signal is clocked correctly, hence, the counter is disabled.
All input pins left open will be pulled LOW via an input pulldown
resistor. Therefore, do not leave the differential CLK inputs open.
Doing so causes the current source transistor of the input clock gate to
become saturated, thus upsetting the internal bias regulators and
jeopardizing the stability of the device.
The asynchronous Master Reset resets the counter to an all zero state
upon assertion.
The VBB pin, an internally generated voltage supply, is available to
this device only. For single-ended input conditions, the unused
differential input is connected to VBB as a switching reference voltage.
VBB may also rebias AC coupled inputs. When used, decouple VBB and
VCC via a 0.01 mF capacitor and limit current sourcing or sinking to
0.5 mA. When not used, VBB should be left open.
The 100 Series contains temperature compensation.
Features
•
•
•
•
•
•
•
•
•
Differential Clock Input and Data Output Pins
VBB Output for Single-Ended Use
Synchronous and Asynchronous Enable Pins
Asynchronous Master Reset
PECL Mode Operating Range:
♦ VCC = 4.2 V to 5.7 V with VEE = 0 V
NECL Mode Operating Range:
♦ VCC = 0 V with VEE = −4.2 V to −5.7 V
Internal Input 50 kW Pull-down Resistors
Transistor Count = 330 devices
ESD Protection:
© Semiconductor Components Industries, LLC, 2016
July, 2016 − Rev. 9
www.onsemi.com
PLCC−28
FN SUFFIX
CASE 776−02
MARKING DIAGRAM*
1
MCxxxE137FNG
AWLYYWW
xxx
A
WL
YY
WW
G
= 10 or 100
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb-Free Package
*For additional marking information, refer to
Application Note AND8002/D.
ORDERING INFORMATION
Device
Package
Shipping†
MC10E137FNG
PLCC−28
(Pb-Free)
37 Units/Tube
MC100E137FNG
PLCC−28
(Pb-Free)
37 Units/Tube
Human Body Model: > 2 kV
Machine Model: > 200 V
Meets or Exceeds JEDEC Spec EIA/JESD78 IC
Latchup Test
Moisture Sensitivity Level: 3 (Pb-Free)
♦ For Additional Information, see Application Note
AND8003/D
Flammability Rating: UL 94 V−0 @ 0.125 in,
Oxygen Index: 28 to 34
These Devices are Pb-Free, Halogen Free and are
RoHS Compliant
♦
•
•
•
•
1
♦
Publication Order Number:
MC10E137/D
MC10E137, MC100E137
Q7
Q7
Q6
Q6
VCCO
Q5
Q5
25
24
23
22
21
20
19
Table 1. PIN DESCRIPTION
A_Start
26
18
Q4
EN1
27
17
Q4
EN2
28
16
VCC
VEE
Pinout: 28-Lead PLCC
(Top View)
1
Q3
15
CLK
2
14
Q3
CLK
3
13
Q2
4
12
Q2
VBB
5
6
MR VCCO
7
8
9
10
11
Q0
Q0
Q1
Q1
VCCO
PIN
FUNCTION
CLK, CLK
ECL Differential Clock Inputs
Q0-Q7, Q0-Q7
ECL Differential Q Outputs
A_Start
ECL Asynchronous Enable Input
EN1, EN2
ECL Synchronous Enable Inputs
MR
Asynchronous Master Reset
VBB
Reference Voltage Output
VCC, VCCO
Positive Supply
VEE
Negative Supply
* All VCC and VCCO pins are tied together on the die.
Warning: All VCC, VCCO, and VEE pins must be externally
connected to Power Supply to guarantee proper operation.
Figure 1. 28-Lead Pinout
A_Start
EN1
EN2
D
VBB
Q0
Q0
Q7 Q7
Q1 Q1
Q
CLK
CLK
CLK
CLK
R
Q
CLK
CLK
D
Q
Q
R
MR
Figure 2. Logic Diagram
www.onsemi.com
2
CLK
CLK
D
Q
Q
R
CLK
CLK
D
Q
Q
R
MC10E137, MC100E137
Table 2. SEQUENTIAL TRUTH TABLE
EN1
EN2
A_Start
MR
CLK
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
Reset
Function
X
X
X
H
X
L
L
L
L
L
L
L
L
Count
L
L
L
L
L
L
L
L
L
L
L
L
Z
Z
Z
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
L
H
Stop
H
H
L
L
L
L
L
L
Z
Z
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
H
Asynch Start
H
H
L
L
L
L
H
H
H
L
L
L
Z
Z
Z
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
L
L
H
L
H
L
Count
L
L
L
L
L
L
L
L
L
L
L
L
Z
Z
Z
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
L
L
H
L
L
H
L
H
Stop
L
L
H
H
L
L
L
L
Z
Z
L
L
L
L
L
L
L
L
H
H
L
L
L
L
H
H
Synch Start
H
H
H
H
H
H
L
L
L
L
L
L
Z
Z
Z
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
L
L
H
H
H
L
L
H
L
Stop
H
H
L
L
L
L
L
L
Z
Z
L
L
L
L
L
L
L
L
H
H
H
H
L
L
L
L
Count
L
L
L
L
L
L
L
L
L
L
L
L
Z
Z
Z
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
H
H
H
L
H
H
H
L
H
Reset
X
X
X
H
X
L
L
L
L
L
L
L
L
Z = Low to High Transition
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
PECL Mode Power Supply
VEE = 0 V
8
V
VEE
NECL Mode Power Supply
VCC = 0 V
−8
V
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
VEE = 0 V
VCC = 0 V
6
−6
V
Iout
Output Current
Continuous
Surge
50
100
mA
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction-to-Ambient)
0 lfpm
500 lfpm
qJC
Thermal Resistance (Junction-to-Case)
Standard Board
VEE
Tsol
VI v VCC
VI w VEE
0 to +85
°C
−65 to +150
°C
PLCC−28
63.5
43.5
°C/W
PLCC−28
22 to 26
°C/W
PECL Operating Range
NECL Operating Range
4.2 to 5.7
−5.7 to −4.2
V
Wave Solder (Pb-Free)
265
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
www.onsemi.com
3
MC10E137, MC100E137
Table 4. 10E SERIES PECL DC CHARACTERISTICS (VCCx = 5.0 V; VEE = 0.0 V (Note 1))
0°C
Symbol
Characteristic
Min
Typ
25°C
Max
Min
Typ
85°C
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
121
145
121
145
121
145
mA
VOH
Output HIGH Voltage (Note 2)
3980
40
70
4160
4020
4105
4190
4090
4185
4280
mV
VOL
Output LOW Voltage (Note 2)
3050
3210
3370
3050
3210
3370
3050
3227
3405
mV
VIH
Input HIGH Voltage (Single-Ended)
3830
3995
4160
3870
4030
4190
3940
4110
4280
mV
VIL
Input LOW Voltage (Single-Ended)
3050
3285
3520
3050
3285
3520
3050
3302
3555
mV
VBB
Output Voltage Reference
3.62
3.73
3.65
3.75
3.69
3.81
V
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
2.2
4.6
2.2
4.6
2.2
4.6
V
150
mA
VIHCMR
IIH
Input HIGH Current
IIL
Input LOW Current
150
0.5
150
0.3
0.5
0.25
0.3
0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.06 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
Table 5. 10E SERIES NECL DC CHARACTERISTICS (VCCx = 0.0 V; VEE = −5.0 V (Note 1))
0°C
Symbol
Characteristic
Min
Typ
25°C
Max
Min
Typ
85°C
Max
Min
Typ
Max
Unit
IEE
Power Supply Current
121
145
121
145
121
145
mA
VOH
Output HIGH Voltage (Note 2)
−1020
−930
−840
−980
−895
−810
−910
−815
−720
mV
VOL
Output LOW Voltage (Note 2)
−1950
−1790
−1630
−1950
−1790
−1630
−1950
−1773
−1595
mV
VIH
Input HIGH Voltage (Single-Ended)
−1170
−1005
−840
−1130
−970
−810
−1060
−890
−720
mV
VIL
Input LOW Voltage (Single-Ended)
−1950
−1715
−1480
−1950
−1715
−1480
−1950
−1698
−1445
mV
VBB
Output Voltage Reference
−1.38
−1.27
−1.35
−1.25
−1.31
−1.19
V
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
−2.8
−0.4
−2.8
−0.4
−2.8
−0.4
V
150
mA
VIHCMR
IIH
Input HIGH Current
IIL
Input LOW Current
150
0.5
0.3
150
0.5
0.065
0.3
0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.06 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
www.onsemi.com
4
MC10E137, MC100E137
Table 6. 100E SERIES PECL DC CHARACTERISTICS (VCCx = 5.0 V; VEE = 0.0 V (Note 1))
0°C
Symbol
Characteristic
Min
25°C
Typ
Max
121
145
Min
85°C
Typ
Max
121
145
Min
Typ
Max
Unit
139
167
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
3975
4050
4120
3975
4050
4120
3975
4050
4120
mV
VOL
Output LOW Voltage (Note 2)
3190
3295
3380
3190
3255
3380
3190
3260
3380
mV
VIH
Input HIGH Voltage (Single-Ended)
3835
3975
4120
3835
3975
4120
3835
3975
4120
mV
VIL
Input LOW Voltage (Single-Ended)
3190
3355
3525
3190
3355
3525
3190
3355
3525
mV
VBB
Output Voltage Reference
3.62
3.73
3.62
3.74
3.62
3.74
V
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
2.2
4.6
2.2
4.6
2.2
4.6
V
150
mA
VIHCMR
IIH
Input HIGH Current
IIL
Input LOW Current
150
0.5
150
0.3
0.5
0.25
0.5
0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V.
2. Outputs are terminated through a 50ĂW resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
Table 7. 100E SERIES NECL DC CHARACTERISTICS (VCCx = 0.0 V; VEE = −5.0 V (Note 1))
0°C
Symbol
Characteristic
Min
25°C
Typ
Max
121
145
Min
85°C
Typ
Max
121
145
Min
Typ
Max
Unit
139
167
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
−1025
−950
−880
−1025
−950
−880
−1025
−950
−880
mV
VOL
Output LOW Voltage (Note 2)
−1810
−1705
−1620
−1810
−1745
−1620
−1810
−1740
−1620
mV
VIH
Input HIGH Voltage (Single-Ended)
−1165
−1025
−880
−1165
−1025
−880
−1165
−1025
−880
mV
VIL
Input LOW Voltage (Single-Ended)
−1810
−1645
−1475
−1810
−1645
−1475
−1810
−1645
−1475
mV
VBB
Output Voltage Reference
−1.38
−1.27
−1.38
−1.26
−1.38
−1.26
V
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 3)
−3.8
−0.4
−3.8
−0.4
−3.8
−0.4
V
150
mA
VIHCMR
IIH
Input HIGH Current
IIL
Input LOW Current
150
0.5
0.3
150
0.5
0.25
0.5
0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
www.onsemi.com
5
MC10E137, MC100E137
Table 8. AC CHARACTERISTICS (VCCx = 5.0 V; VEE = 0.0 V or VCCx = 0.0 V; VEE = −5.0 V (Note 1))
0°C
Symbol
Characteristic
Min
Typ
fCOUNT
Maximum Count Frequency
1800
2200
tPLH
tPHL
Propagation Delay to Output
CLK to Q0
CLK to Q1
CLK to Q2
CLK to Q3
CLK to Q4
CLK to Q5
CLK to Q6
CLK to Q7
A_Start to Q0
MR to Q0
1300
1600
1950
2275
2625
2950
3250
3575
950
700
1700
2025
2425
2750
3125
3450
3775
4075
1325
1000
25°C
Max
2150
2500
2925
3350
3750
4150
4450
4800
1700
1300
Min
Typ
1800
2200
1300
1600
1950
2275
2625
2950
3250
3575
950
700
1700
2050
2450
2775
3150
3475
3800
4125
1325
1000
85°C
Max
2150
2500
2925
3350
3750
4150
4450
4800
1700
1300
Min
Typ
1800
2200
1350
1650
2025
2350
2700
3050
3375
3700
950
700
1750
2100
2500
2850
3225
3550
3925
4250
1325
1000
Max
Unit
MHz
2200
2550
3000
3425
3825
4250
4600
4950
1700
1300
ps
ts
Setup Time (EN1, EN2)
0
−150
0
−150
0
−150
ps
th
Hold Time (EN1, EN2)
300
150
300
150
300
150
ps
tRR
Reset Recovery Time
MR, A_Start
400
200
400
200
400
200
ps
tPW
Minimum Pulse Width
CLK, MR, A_Start
400
VPP
Input Voltage Swing
CLK/CLK (Differential Configuration)
(Note 2)
0.25
tJITTER
Random Clock Jitter (RMS)
tr
tf
Rise/Fall Times (20%−80%)
Q0,Q1
Q2 to Q7
400
1.0
0.25
<1
150
275
400
1.0
0.25
<1
400
600
150
275
ps
1.0
<1
400
600
150
275
V
ps
400
600
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. 10 Series: VEE can vary −0.46 V / +0.06 V.
100 Series: VEE can vary −0.46 V / +0.8 V.
2. Minimum input swing for which AC parameters are guaranteed. Full DC ECL output swings will be generated with only 50 mV input swings.
www.onsemi.com
6
MC10E137, MC100E137
Q
Zo = 50 W
D
Receiver
Device
Driver
Device
Q
D
Zo = 50 W
50 W
50 W
VTT
VTT = VCC − 2.0 V
Figure 3. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices.)
Resource Reference of Application Notes
AN1405/D
− ECL Clock Distribution Techniques
AN1406/D
− Designing with PECL (ECL at +5.0 V)
AN1503/D
− ECLinPSt I/O SPiCE Modeling Kit
AN1504/D
− Metastability and the ECLinPS Family
AN1568/D
− Interfacing Between LVDS and ECL
AN1672/D
− The ECL Translator Guide
AND8001/D
− Odd Number Counters Design
AND8002/D
− Marking and Date Codes
AND8020/D
− Termination of ECL Logic Devices
AND8066/D
− Interfacing with ECLinPS
AND8090/D
− AC Characteristics of ECL Devices
www.onsemi.com
7
MC10E137, MC100E137
PACKAGE DIMENSIONS
28 LEAD PLCC
CASE 776−02
ISSUE F
B
Y BRK
−N−
0.007 (0.180)
U
M
T L-M
0.007 (0.180)
M
N
S
T L-M
S
S
N
S
D
Z
−M−
−L−
W
28
D
X
V
1
G1
0.010 (0.250)
T L-M
S
N
S
S
VIEW D−D
Z
A
0.007 (0.180)
R
0.007 (0.180)
M
M
T L-M
S
T L-M
S
N
N
H
S
0.007 (0.180)
M
T L-M
N
S
S
S
K1
C
E
0.004 (0.100)
G
J
S
K
SEATING
PLANE
F
VIEW S
G1
0.010 (0.250)
−T−
T L-M
S
N
VIEW S
S
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM -T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALLOWABLE MOLD FLASH IS
0.010 (0.250) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.485
0.495
0.485
0.495
0.165
0.180
0.090
0.110
0.013
0.021
0.050 BSC
0.026
0.032
0.020
--0.025
--0.450
0.456
0.450
0.456
0.042
0.048
0.042
0.048
0.042
0.056
--0.020
2_
10_
0.410
0.430
0.040
---
www.onsemi.com
8
MILLIMETERS
MIN
MAX
12.32
12.57
12.32
12.57
4.20
4.57
2.29
2.79
0.33
0.53
1.27 BSC
0.66
0.81
0.51
--0.64
--11.43
11.58
11.43
11.58
1.07
1.21
1.07
1.21
1.07
1.42
--0.50
2_
10_
10.42
10.92
1.02
---
0.007 (0.180)
M
T L-M
S
N
S
MC10E137, MC100E137
ECLinPS is a registered trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC10E137/D
Similar pages