NX3L1T66 Low-ohmic single-pole single-throw analog switch Rev. 01 — 14 September 2009 Product data sheet 1. General description The NX3L1T66 provides one single-pole single-throw analog switch function. It has two input/output terminals (Y and Z) and an active HIGH enable input pin (E). When E is LOW, the analog switch is turned off. Schmitt-trigger action at the enable input (E) makes the circuit tolerant to slower input rise and fall times across the entire VCC range from 1.4 V to 4.3 V. A low input voltage threshold allows pin E to be driven by lower level logic signals without a significant increase in supply current ICC. This makes it possible for the NX3L1T66 to switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for logic level translation. The NX3L1T66 allows signals with amplitude up to VCC to be transmitted from nY to nZ; or from nZ to nY. Its low ON resistance (0.5 Ω) and flatness (0.13 Ω) ensures minimal attenuation and distortion of transmitted signals. 2. Features n Wide supply voltage range from 1.4 V to 4.3 V n Very low ON resistance (peak): u 1.6 Ω (typical) at VCC = 1.4 V u 1.0 Ω (typical) at VCC = 1.65 V u 0.55 Ω (typical) at VCC = 2.3 V u 0.50 Ω (typical) at VCC = 2.7 V u 0.50 Ω (typical) at VCC = 4.3 V n High noise immunity n ESD protection: u HBM JESD22-A114E Class 3A exceeds 7500 V u MM JESD22-A115-A exceeds 200 V u CDM AEC-Q100-011 revision B exceeds 1000 V n CMOS low-power consumption n Latch-up performance exceeds 100 mA per JESD 78 Class II Level A n 1.8 V control logic at VCC = 3.6 V n Control input accepts voltages above supply voltage n Very low supply current, even when input is below VCC n High current handling capability (350 mA continuous current under 3.3 V supply) n Specified from −40 °C to +85 °C and from −40 °C to +125 °C NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 3. Applications n Cell phone n PDA n Portable media player 4. Ordering information Table 1. Ordering information Type number Package NX3L1T66GW −40 °C to +125 °C TSSOP5 plastic thin shrink small outline package; 5 leads; body width 1.25 mm SOT353-1 NX3L1T66GM −40 °C to +125 °C XSON6 SOT886 Temperature range Name Description Version plastic extremely thin small outline package; no leads; 6 terminals; body 1 × 1.45 × 0.5 mm 5. Marking Table 2. Marking codes[1] Type number Marking code NX3L1T66GW DO NX3L1T66GM DO [1] The pin 1 indicator is located on the lower left corner of the device, below the marking code. 6. Functional diagram Y E Z Z Y E 001aah372 001aag487 Fig 1. Logic symbol Fig 2. Logic diagram NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 2 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 7. Pinning information 7.1 Pinning NX3L1T66 NX3L1T66 Y 1 Z 2 GND 3 5 4 VCC Y 1 6 VCC Z 2 5 n.c. GND 3 4 E E 001aaj983 Transparent top view 001aaj982 Fig 3. Pin configuration SOT353-1 (TSSOP5) Fig 4. Pin configuration SOT886 (XSON6) 7.2 Pin description Table 3. Pin description Symbol Pin Description SOT353-1 SOT886 Y 1 1 independent input or output Z 2 2 independent output or input GND 3 3 ground (0 V) E 4 4 enable input (active HIGH) n.c. - 5 not connected VCC 5 6 supply voltage 8. Functional description Table 4. Function table[1] Input E Switch L OFF-state H ON-state [1] H = HIGH voltage level; L = LOW voltage level. NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 3 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 9. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter VCC supply voltage Conditions Min Max Unit −0.5 +4.6 V −0.5 +4.6 V −0.5 VCC + 0.5 V VI input voltage [1] VSW switch voltage [2] IIK input clamping current VI < −0.5 V −50 - mA ISK switch clamping current VI < −0.5 V or VI > VCC + 0.5 V - ±50 mA ISW switch current VSW > −0.5 V or VSW < VCC + 0.5 V; source or sink current - ±350 mA VSW > −0.5 V or VSW < VCC + 0.5 V; pulsed at 1 ms duration, < 10 % duty cycle; peak current - ±500 mA −65 +150 °C - 250 mW Tstg storage temperature total power dissipation Ptot Tamb = −40 °C to +125 °C [3] [1] The minimum input voltage rating may be exceeded if the input current rating is observed. [2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not exceed 4.6 V. [3] For TSSOP5 package: above 87.5 °C the value of Ptot derates linearly with 4.0 mW/K. For XSON6 package: above 118 °C the value of Ptot derates linearly with 7.8 mW/K. 10. Recommended operating conditions Table 6. Recommended operating conditions Symbol Parameter VCC supply voltage VI input voltage VSW Conditions enable input E [1] switch voltage Tamb ambient temperature ∆t/∆V input transition rise and fall rate VCC = 1.4 V to 4.3 V [2] Min Max Unit 1.4 4.3 V 0 4.3 V 0 VCC V −40 +125 °C - 200 ns/V [1] To avoid sinking GND current from of terminal Z when switch current flows in terminal Y, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal Z, no GND current will flow from terminal Y. In this case, there is no limit for the voltage drop across the switch. [2] Applies to control signal levels. NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 4 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 11. Static characteristics Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground 0 V). Symbol Parameter VIH VIL Max Min VCC = 1.4 V to 1.6 V 0.9 - - 0.9 - - V VCC = 1.65 V to 1.95 V 0.9 - - 0.9 - - V VCC = 2.3 V to 2.7 V 1.1 - - 1.1 - - V VCC = 2.7 V to 3.6 V 1.3 - - 1.3 - - V VCC = 3.6 V to 4.3 V 1.4 - - 1.4 - - V VCC = 1.4 V to 1.6 V - - 0.3 - 0.3 0.3 V VCC = 1.65 V to 1.95 V - - 0.4 - 0.4 0.3 V VCC = 2.3 V to 2.7 V - - 0.4 - 0.4 0.4 V VCC = 2.7 V to 3.6 V - - 0.5 - 0.5 0.5 V VCC = 3.6 V to 4.3 V - - 0.6 - 0.6 0.6 V - - - - ±0.5 ±1 µA VCC = 1.4 V to 3.6 V - - ±5 - ±50 ±500 nA VCC = 3.6 V to 4.3 V - - ±10 - ±50 ±500 nA VCC = 1.4 V to 3.6 V - - ±5 - ±50 ±500 nA VCC = 3.6 V to 4.3 V - - ±10 - ±50 ±500 nA VCC = 3.6 V - - 100 - 690 6000 nA VCC = 4.3 V - - 150 - 800 7000 nA additional VSW = GND or VCC supply current VI = 2.6 V; VCC = 4.3 V - 2.0 4.0 - 7 7 µA VI = 2.6 V; VCC = 3.6 V - 0.35 0.7 - 1 1 µA VI = 1.8 V; VCC = 4.3 V - 7.0 10.0 - 15 15 µA VI = 1.8 V; VCC = 3.6 V - 2.5 4.0 - 5 5 µA VI = 1.8 V; VCC = 2.5 V - 50 200 - 300 500 nA HIGH-level input voltage LOW-level input voltage enable input E; VI = GND to 4.3 V; VCC = 1.4 V to 4.3 V IS(OFF) OFF-state leakage current Y port; see Figure 5 ON-state leakage current Z port; see Figure 6 ∆ICC Unit Typ input leakage current ICC −40 °C to +125 °C Min II IS(ON) 25 °C Conditions Max Max (85 °C) (125 °C) supply current VI = VCC or GND; VSW = GND or VCC CI input capacitance - 1.0 - - - - pF CS(OFF) OFF-state capacitance - 35 - - - - pF CS(ON) ON-state capacitance - 110 - - - - pF NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 5 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 11.1 Test circuits VCC VCC E VIL Z VI E VIH Y IS IS GND Z GND VI VO Y 001aag488 001aag489 VI = 0.3 V or VCC − 0.3 V; VO = VCC − 0.3 V or 0.3 V. Fig 5. VO VI = 0.3 V or VCC − 0.3 V; VO = open circuit. Test circuit for measuring OFF-state leakage current Fig 6. Test circuit for measuring ON-state leakage current 11.2 ON resistance Table 8. ON resistance At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 8 to Figure 14. Symbol RON(peak) Parameter ON resistance (peak) Tamb = −40 °C to +85 °C Conditions Min Max Min Max VCC = 1.4 V - 1.6 3.7 - 4.1 Ω VCC = 1.65 V - 1.0 1.6 - 1.7 Ω VCC = 2.3 V - 0.55 0.8 - 0.9 Ω VCC = 2.7 V - 0.5 0.75 - 0.9 Ω - 0.5 0.75 - 0.9 Ω VCC = 1.4 V - 1.0 3.3 - 3.6 Ω VCC = 1.65 V - 0.5 1.2 - 1.3 Ω VCC = 2.3 V - 0.15 0.3 - 0.35 Ω VCC = 2.7 V - 0.13 0.3 - 0.35 Ω VCC = 4.3 V - 0.2 0.4 - 0.45 Ω VI = GND to VCC; ISW = 100 mA; see Figure 7 VCC = 4.3 V RON(flat) ON resistance (flatness) Tamb = −40 °C to +125 °C Unit Typ[1] VI = GND to VCC; ISW = 100 mA [2] [1] Typical values are measured at Tamb = 25 °C. [2] Flatness is defined as the difference between the maximum and minimum value of ON resistance measured at identical VCC and temperature. NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 6 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 11.3 ON resistance test circuit and graphs 001aag564 1.6 RON (Ω) 1.2 VSW (1) 0.8 VCC (2) E VIH (3) Z VI GND (4) 0.4 Y (5) (6) ISW 0 0 1 2 RON = VSW / ISW. 3 4 5 VI (V) 001aah375 (1) VCC = 1.5 V. (2) VCC = 1.8 V. (3) VCC = 2.5 V. (4) VCC = 2.7 V. (5) VCC = 3.3 V. (6) VCC = 4.3 V. Measured at Tamb = 25 °C. Fig 7. Test circuit for measuring ON resistance Fig 8. Typical ON resistance as a function of input voltage NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 7 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 001aag565 1.6 001aag566 1.0 RON (Ω) RON (Ω) 0.8 1.2 (1) (2) (3) (4) 0.6 (1) (2) (3) (4) 0.8 0.4 0.4 0.2 0 0 0 1 2 3 0 1 2 VI (V) (1) Tamb = 125 °C. (1) Tamb = 125 °C. (2) Tamb = 85 °C. (2) Tamb = 85 °C. (3) Tamb = 25 °C. (3) Tamb = 25 °C. (4) Tamb = −40 °C. (4) Tamb = −40 °C. Fig 9. ON resistance as a function of input voltage; VCC = 1.5 V 001aag567 1.0 3 VI (V) RON (Ω) Fig 10. ON resistance as a function of input voltage; VCC = 1.8 V 001aag568 1.0 RON (Ω) 0.8 0.8 0.6 0.6 (1) (2) (3) (4) 0.4 0.4 0.2 0.2 0 (1) (2) (3) (4) 0 0 1 2 3 0 VI (V) 2 3 VI (V) (1) Tamb = 125 °C. (1) Tamb = 125 °C. (2) Tamb = 85 °C. (2) Tamb = 85 °C. (3) Tamb = 25 °C. (3) Tamb = 25 °C. (4) Tamb = −40 °C. (4) Tamb = −40 °C. Fig 11. ON resistance as a function of input voltage; VCC = 2.5 V Fig 12. ON resistance as a function of input voltage; VCC = 2.7 V NX3L1T66_1 Product data sheet 1 © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 8 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 001aag569 1.0 RON (Ω) 001aaj896 1.0 RON (Ω) 0.8 0.8 0.6 0.6 (1) (2) (3) (4) 0.4 (1) (2) (3) (4) 0.4 0.2 0.2 0 0 0 1 2 3 4 0 1 2 3 4 VI (V) (1) Tamb = 125 °C. (1) Tamb = 125 °C. (2) Tamb = 85 °C. (2) Tamb = 85 °C. (3) Tamb = 25 °C. (3) Tamb = 25 °C. (4) Tamb = −40 °C. (4) Tamb = −40 °C. Fig 13. ON resistance as a function of input voltage; VCC = 3.3 V 5 VI (V) Fig 14. ON resistance as a function of input voltage; VCC = 4.3 V 12. Dynamic characteristics Table 9. Dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for load circuit see Figure 16. Symbol Parameter enable time ten disable time tdis [1] 25 °C Conditions −40 °C to +125 °C Unit Min Typ[1] Max Min Max (85 °C) Max (125 °C) VCC = 1.4 V to 1.6 V - 35 49 - 53 57 ns VCC = 1.65 V to 1.95 V - 28 40 - 43 48 ns VCC = 2.3 V to 2.7 V - 20 30 - 32 35 ns VCC = 2.7 V to 3.6 V - 18 28 - 30 32 ns VCC = 3.6 V to 4.3 V - 18 28 - 30 32 ns VCC = 1.4 V to 1.6 V - 32 70 - 80 90 ns VCC = 1.65 V to 1.95 V - 23 55 - 60 65 ns VCC = 2.3 V to 2.7 V - 14 25 - 30 35 ns VCC = 2.7 V to 3.6 V - 11 20 - 25 30 ns VCC = 3.6 V to 4.3 V - 11 20 - 25 30 ns E to Z or Y; see Figure 15 E to Z or Y; see Figure 15 Typical values are measured at Tamb = 25 °C and VCC = 1.5 V, 1.8 V, 2.5 V, 3.3 V and 4.3 V respectively. NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 9 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 12.1 Waveform and test circuits VI E input VM GND ten Y output OFF to HIGH HIGH to OFF tdis VOH VX VX GND switch disabled switch enabled switch disabled 001aah875 Measurement points are given in Table 10. Logic level: VOH is the typical output voltage that occurs with the output load. Fig 15. Enable and disable times Table 10. Measurement points Supply voltage Input Output VCC VM VX 1.4 V to 4.3 V 0.5VCC 0.9VOH VCC E Y/Z G VI V VO RL Z/Y CL VEXT = 1.5 V 001aah377 Test data is given in Table 11. Definitions test circuit: RL = Load resistance. CL = Load capacitance including jig and probe capacitance. VEXT = External voltage for measuring switching times. Fig 16. Load circuit for switching times Table 11. Test data Supply voltage Input Load VCC VI tr, tf CL RL 1.4 V to 4.3 V VCC ≤ 2.5 ns 35 pF 50 Ω NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 10 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 12.2 Additional dynamic characteristics Table 12. Additional dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); VI = GND or VCC (unless otherwise specified); tr = tf ≤ 2.5 ns. 25 °C Symbol Parameter Conditions THD fi = 20 Hz to 20 kHz; RL = 32 Ω; see Figure 17 total harmonic distortion Min Typ Max VCC = 1.4 V; VI = 1 V (p-p) - 0.15 - % VCC = 1.65 V; VI = 1.2 V (p-p) - 0.10 - % [1] VCC = 2.3 V; VI = 1.5 V (p-p) - 0.02 - % VCC = 2.7 V; VI = 2 V (p-p) - 0.02 - % - 0.02 - % - 60 - MHz - −90 - dB VCC = 1.4 V to 3.6 V - 0.2 - V VCC = 3.6 V to 4.3 V - 0.2 - V VCC = 1.5 V - 3 - pC VCC = 1.8 V - 3 - pC VCC = 2.5 V - 3 - pC VCC = 3.3 V - 3 - pC VCC = 4.3 V - 6 - pC VCC = 4.3 V; VI = 2 V (p-p) f(−3dB) −3 dB frequency response RL = 50 Ω; see Figure 18 αiso isolation (OFF-state) fi = 100 kHz; RL = 50 Ω; see Figure 19 crosstalk voltage charge injection Qinj [1] [1] VCC = 1.4 V to 4.3 V VCC = 1.4 V to 4.3 V Vct Unit [1] between digital inputs and switch; fi = 1 MHz; CL = 50 pF; RL = 50 Ω; see Figure 20 fi = 1 MHz; CL = 0.1 nF; RL = 1 MΩ; Vgen = 0 V; Rgen = 0 Ω; see Figure 21 fi is biased at 0.5VCC. NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 11 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 12.3 Test circuits VCC 0.5VCC E VIH RL Y/Z Z/Y D fi 001aah378 Fig 17. Test circuit for measuring total harmonic distortion VCC 0.5VCC E VIH RL Y/Z Z/Y dB fi 001aah379 Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads −3 dB. Fig 18. Test circuit for measuring the frequency response when channel is in ON-state 0.5VCC RL VCC VIL 0.5VCC E Y/Z RL Z/Y dB fi 001aah380 Adjust fi voltage to obtain 0 dBm level at input. Fig 19. Test circuit for measuring isolation (OFF-state) NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 12 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch VCC E Y/Z G VI Z/Y RL RL 0.5VCC 0.5VCC CL V VO 001aah383 a. Test circuit logic input (E) off on off VO Vct 001aah381 b. Input and output pulse definitions Fig 20. Test circuit for measuring crosstalk voltage between digital inputs and switch NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 13 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch VCC E Y/Z G VI V VO RL Z/Y Rgen CL Vgen GND 001aah385 a. Test circuit logic input (E) off on VO off VO 001aah384 b. Input and output pulse definitions Definition: Qinj = ∆VO × CL. ∆VO = output voltage variation. Rgen = generator resistance. Vgen = generator voltage. Fig 21. Test circuit for measuring charge injection NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 14 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 13. Package outline TSSOP5: plastic thin shrink small outline package; 5 leads; body width 1.25 mm E D SOT353-1 A X c y HE v M A Z 5 4 A2 A (A3) A1 θ 1 Lp 3 L e w M bp detail X e1 0 1.5 3 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D(1) E(1) e e1 HE L Lp v w y Z(1) θ mm 1.1 0.1 0 1.0 0.8 0.15 0.30 0.15 0.25 0.08 2.25 1.85 1.35 1.15 0.65 1.3 2.25 2.0 0.425 0.46 0.21 0.3 0.1 0.1 0.60 0.15 7° 0° Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT353-1 REFERENCES IEC JEDEC JEITA MO-203 SC-88A EUROPEAN PROJECTION ISSUE DATE 00-09-01 03-02-19 Fig 22. Package outline SOT353-1 (TSSOP5) NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 15 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm SOT886 b 1 2 3 4× (2) L L1 e 6 5 e1 4 e1 6× A (2) A1 D E terminal 1 index area 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A (1) max A1 max b D E e e1 L L1 mm 0.5 0.04 0.25 0.17 1.5 1.4 1.05 0.95 0.6 0.5 0.35 0.27 0.40 0.32 Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. OUTLINE VERSION SOT886 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 04-07-15 04-07-22 MO-252 Fig 23. Package outline SOT886 (XSON6) NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 16 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 14. Abbreviations Table 13. Abbreviations Acronym Description CDM Charged-Device Model CMOS Complementary Metal-Oxide Semiconductor ESD ElectroStatic Discharge HBM Human Body Model MM Machine Model PDA Personal Digital Assistant TTL Transistor-Transistor Logic 15. Revision history Table 14. Revision history Document ID Release date Data sheet status Change notice Supersedes NX3L1T66_1 20090914 Product data sheet - - NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 17 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 16.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] NX3L1T66_1 Product data sheet © NXP B.V. 2009. All rights reserved. Rev. 01 — 14 September 2009 18 of 19 NX3L1T66 NXP Semiconductors Low-ohmic single-pole single-throw analog switch 18. Contents 1 2 3 4 5 6 7 7.1 7.2 8 9 10 11 11.1 11.2 11.3 12 12.1 12.2 12.3 13 14 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ON resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ON resistance test circuit and graphs. . . . . . . . 7 Dynamic characteristics . . . . . . . . . . . . . . . . . . 9 Waveform and test circuits . . . . . . . . . . . . . . . 10 Additional dynamic characteristics . . . . . . . . . 11 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 15 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 17 Legal information. . . . . . . . . . . . . . . . . . . . . . . 18 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 18 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Contact information. . . . . . . . . . . . . . . . . . . . . 18 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2009. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 14 September 2009 Document identifier: NX3L1T66_1