ON MC79M08CDTRK 500 ma negative voltage regulator Datasheet

MC79M00 Series
500 mA Negative Voltage
Regulators
The MC79M00 series of fixed output negative voltage regulators
are intended as complements to the popular MC78M00 series devices.
Available in fixed output voltage options of −5.0 V, −8.0 V, −12 V
and −15 V, these regulators employ current limiting, thermal
shutdown, and safe−area compensation, making them remarkably
rugged under most operating conditions. With adequate heatsinking
they can deliver output currents in excess of 0.5 A.
• No External Components Required
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting
• Output Transistor Safe−Area Compensation
• Also Available in Surface Mount DPAK (DT) Package
• Pb−Free Packages are Available
Nominal Output Voltage
MC79M05
MC79M08
MC79M12
MC79M15
THREE−TERMINAL
NEGATIVE FIXED
VOLTAGE REGULATORS
STANDARD APPLICATION
MC79MXX
Input
−5.0 V
−8.0 V
−12 V
−15 V
CO**
1.0 mF
Cin*
0.33 mF
MARKING
DIAGRAMS
R1
4.0 k
2.0 k
4.9 k
1.0 k
12 k
1.2 k
547
11.5 k
2.0 k
2.0 k
14.7 k
3.6 k
25
2.4 k
GND
Pin 1. Ground
2. Input
3. Output
1
2
R2
3
VO
10 k
20 pF
2.0 k
20 k 20 k
MC
79MxxyT
AWLYWWG
TO−220−3
T SUFFIX
CASE 221AB
4
10 pF 10 k
1.1 k
Output
A common ground is required between the input
and the output voltages. The input voltage must
remain typically 1.1 V more negative even during
the high point of the input ripple voltage.
XX These two digits of the type number indicate
nominal voltage.
* Cin is required if regulator is located an
appreciable distance from power supply filter.
** CO improve stability and transient response.
DEVICE TYPE/NOMINAL OUTPUT VOLTAGE
Device
http://onsemi.com
240
0.3
100
750
VI
This device contains 31 active transistors.
Figure 1. Representative Schematic Diagram
9MxxBG
ALYWW
1 2
79MxxG
ALYWW
3
DPAK−3
DT SUFFIX
CASE 369C
xx
y
A
WL, L
Y
WW
G
= 05, 08, 12, or 15
= B or C
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Device
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 5 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
August, 2006 − Rev. 11
1
Publication Order Number:
MC79M00/D
MC79M00 Series
MAXIMUM RATINGS (TA = 25°C, unless otherwise noted.)
Symbol
Value
Unit
VI
−35
Vdc
TA = 25°C
PD
Internally Limited
W
Thermal Resistance, Junction−to−Ambient
qJA
65
°C/W
Thermal Resistance, Junction−to−Case
qJC
5.0
°C/W
TA = 25°C
PD
Internally Limited
W
Thermal Resistance, Junction−to−Ambient
qJA
92
°C/W
Thermal Resistance, Junction−to−Case
qJC
6.0
°C/W
Storage Junction Temperature
Tstg
−65 to +150
°C
Operating Junction Temperature Range
TJ
−40 to +150
°C
Rating
Input Voltage
Power Dissipation
Case 221A (TO−220−3)
Case 369C (DPAK−3)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
*This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL_STD_883, Method 3015
Machine Model Method 200 V
MC79M05B, C
ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 350 mA, Tlow to Thigh (Note 2), unless otherwise noted.)
Characteristic
Output Voltage (TJ = 25°C)
Symbol
Min
Typ
Max
Unit
VO
−4.8
−5.0
−5.2
Vdc
−
−
7.0
2.0
50
30
−
30
100
−4.75
−
−5.25
−
4.3
8.0
−
−
−
−
0.4
0.4
Line Regulation, TJ = 25°C (Note 1)
−7.0 Vdc ≥ VI ≥ −25 Vdc
−8.0 Vdc ≥ VI ≥ −18 Vdc
Regline
Load Regulation, TJ = 25°C (Note 1)
5.0 mA ≤ IO ≤ 500 mA
Regload
Output Voltage
−7.0 Vdc ≥ VI ≥ −25 Vdc, 5.0 mA ≤ IO ≤ 350 mA
VO
Input Bias Current (TJ = 25°C)
IIB
mV
mV
Vdc
DIIB
Input Bias Current Change
−8.0 Vdc ≥ VI ≥ −25 Vdc, IO = 350 mA
5.0 mA ≤ IO ≤ 350 mA, VI = −10 V
mA
mA
Output Noise Voltage, TA = 25°C, 10 Hz ≤ f ≤ 100 kHz
Vn
−
40
−
mV
Ripple Rejection (f = 120 Hz)
RR
54
66
−
dB
−
1.1
−
−
0.2
−
Dropout Voltage
IO = 500 mA, TJ = 25°C
VI−VO
Vdc
DVO/DT
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, 0°C ≤ TJ ≤ 125°C
mV/°C
1. Load and line regulation are specified at constant temperature. Change in VO due to heating effects must be taken into account separately.
Pulse testing with low duty cycle is used.
2. B = Tlow to Thigh, −40°C < TJ < 125°C C = Tlow to Thigh, 0°C < TJ < 125°C.
http://onsemi.com
2
MC79M00 Series
MC79M08B, C
ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 350 mA, Tlow to Thigh (Note 4), unless otherwise noted.)
Characteristic
Output Voltage (TJ = 25°C)
Symbol
Min
Typ
Max
Unit
VO
−7.7
−8.0
−8.3
Vdc
−
−
5.0
3.0
80
50
−
30
100
−7.6
−8.0
−8.4
−
−
8.0
−
−
−
−
0.4
0.4
Line Regulation, TJ = 25°C (Note 3)
−7.0 Vdc ≥ VI ≥ −25 Vdc
−8.0 Vdc ≥ VI ≥ −18 Vdc
Regline
Load Regulation, TJ = 25°C (Note 3)
5.0 mA ≤ IO ≤ 500 mA
Regload
Output Voltage
−7.0 Vdc ≥ VI ≥ −25 Vdc, 5.0 mA ≤ IO ≤ 350 mA
VO
Input Bias Current (TJ = 25°C)
IIB
mV
mV
Vdc
DIIB
Input Bias Current Change
−8.0 Vdc ≥ VI ≥ −25 Vdc, IO = 350 mA
5.0 mA ≤ IO ≤ 350 mA, VI = −10 V
mA
mA
Output Noise Voltage, TA = 25°C, 10 Hz ≤ f ≤ 100 kHz
Vn
−
60
−
mV
Ripple Rejection (f = 120 Hz)
RR
54
63
−
dB
−
1.1
−
−
0.4
−
Dropout Voltage
IO = 500 mA, TJ = 25°C
VI−VO
Vdc
DVO/DT
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, 0°C ≤ TJ ≤ 125°C
mV/°C
3. Load and line regulation are specified at constant temperature. Change in VO due to heating effects must be taken into account separately.
Pulse testing with low duty cycle is used.
4. B = Tlow to Thigh, −40°C < TJ < 125°C
C = Tlow to Thigh, 0°C < TJ < 125°C
MC79M12B, C
ELECTRICAL CHARACTERISTICS (VI = −19 V, IO = 350 mA, Tlow to Thigh (Note 6), unless otherwise noted.)
Characteristic
Output Voltage (TJ = 25°C)
Symbol
Min
Typ
Max
Unit
VO
−11.5
−12
−12.5
Vdc
−
−
5.0
3.0
80
50
−
30
240
−11.4
−
−12.6
−
4.4
8.0
−
−
−
−
0.4
0.4
Line Regulation, TJ = 25°C (Note 5)
−14.5 Vdc ≥ VI ≥ −30 Vdc
−15 Vdc ≥ VI ≥ −25 Vdc
Regline
Load Regulation, TJ = 25°C (Note 5)
5.0 mA ≤ IO ≤ 500 mA
Regload
Output Voltage
−14.5 Vdc ≥ VI ≥ −30 Vdc, 5.0 mA ≤ IO ≤ 350 mA
mV
mV
VO
Input Bias Current (TJ = 25°C)
IIB
Vdc
DIIB
Input Bias Current Change
−14.5 Vdc ≥ VI ≥ −30 Vdc, IO = 350 mA
5.0 mA ≤ IO ≤ 350 mA, VI = −19 V
mA
mA
Output Noise Voltage, TA = 25°C, 10 Hz ≤ f ≤ 100 kHz
Vn
−
75
−
mV
Ripple Rejection (f = 120 Hz)
RR
54
60
−
dB
−
1.1
−
−
−0.8
−
Dropout Voltage
IO = 500 mA, TJ = 25°C
VI−VO
Vdc
DVO/DT
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, 0°C ≤ TJ ≤ 125°C
mV/°C
5. Load and line regulation are specified at constant temperature. Change in VO due to heating effects must be taken into account separately.
Pulse testing with low duty cycle is used.
6. B = Tlow to Thigh, −40°C < TJ < 125°C
C = Tlow to Thigh, 0°C < TJ < 125°C
http://onsemi.com
3
MC79M00 Series
MC79M15B, C
ELECTRICAL CHARACTERISTICS (VI = − 23 V, IO = 350 mA, Tlow to Thigh (Note 8), unless otherwise noted.)
Characteristic
Output Voltage (TJ = 25°C)
Symbol
Min
Typ
Max
Unit
VO
−14.4
−15
−15.6
Vdc
−
−
5.0
3.0
80
50
−
30
240
−14.25
−
−15.75
−
4.4
8.0
−
−
−
−
0.4
0.4
Line Regulation, TJ = 25°C (Note 7)
−17.5 Vdc ≥ VI ≥ −30 Vdc
−18 Vdc ≥ VI ≥ −28 Vdc
Regline
Load Regulation, TJ = 25°C (Note 7)
5.0 mA ≤ IO ≤ 500 mA
Regload
Output Voltage
−17.5 Vdc ≥ VI ≥ −30 Vdc, 5.0 mA ≤ IO ≤ 350 mA
VO
Input Bias Current (TJ = 25°C)
IIB
mV
mV
Vdc
DIIB
Input Bias Current Change
−17.5 Vdc ≥ VI ≥ −30 Vdc, IO = 350 mA
5.0 mA ≤ IO ≤ 350 mA, VI = −23 V
mA
mA
Output Noise Voltage, TA = 25°C, 10 Hz ≤ f ≤ 100 kHz
Vn
−
90
−
mV
Ripple Rejection (f = 120 Hz)
RR
54
60
−
dB
−
1.1
−
−
−1.0
−
Dropout Voltage
IO = 500 mA, TJ = 25°C
VI−VO
Vdc
DVO/DT
Average Temperature Coefficient of Output Voltage
IO = 5.0 mA, 0°C ≤ TJ ≤ 125°C
mV/°C
JUNCTION-TO-AIR (°C/W)
R θ JA, THERMAL RESISTANCE
100
90
2.0
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
80
Minimum
Size Pad
70
2.4
PD(max) for TA = 50°C
Free Air
Mounted
Vertically
60
2.0 oz. Copper
L
1.6
L
1.2
0.8
50
0.4
RqJA
40
0
5.0
10
15
20
25
30
0
L, LENGTH OF COPPER (mm)
Figure 1. DPAK−3 Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
http://onsemi.com
4
PD, MAXIMUM POWER DISSIPATION (W)
7. Load and line regulation are specified at constant temperature. Change in VO due to heating effects must be taken into account separately.
Pulse testing with low duty cycle is used.
8. B = Tlow to Thigh, −40°C < TJ < 125°C
C = Tlow to Thigh, 0°C < TJ < 125°C
MC79M00 Series
ORDERING INFORMATION
Device
Output Voltage
Tolerance
Operating
Temperature Range
MC79M05BDT
MC79M05BDTG
MC79M05BDTRK
TJ = −40°C to +125°C
MC79M05BDTRKG
MC79M05BT
MC79M05BTG
MC79M05CDT
MC79M05CDTG
MC79M05CDTRK
TJ = 0°C to +125°C
MC79M05CDTRKG
MC79M05CT
MC79M05CTG
MC79M08BDT
MC79M08BDTRK
MC79M08BDTRKG
TJ = −40°C to +125°C
MC79M08BT
MC79M08BTG
MC79M08CDT
4.0%
MC79M08CDTG
MC79M08CDTRK
MC79M08CDTRKG
TJ = 0°C to +125°C
MC79M08CT
MC79M08CTG
MC79M12BDT
MC79M12BDTG
MC79M12BDTRK
MC79M12BDTRKG
TJ = −40°C to +125°C
MC79M12BT
MC79M12BTG
MC79M12CDT
MC79M12CDTG
MC79M12CDTRK
MC79M12CDTRKG
TJ = 0°C to +125°C
MC79M12CT
MC79M12CTG
Package
Shipping†
DPAK
DPAK
(Pb−Free)
75 Units / Rail
DPAK
DPAK
(Pb−Free)
2500 Units / Reel
TO−220
TO−220
(Pb−Free)
50 Units / Rail
DPAK
DPAK
(Pb−Free)
75 Units / Rail
DPAK
DPAK
(Pb−Free)
2500 Units / Reel
TO−220
TO−220
(Pb−Free)
50 Units / Rail
DPAK
DPAK
DPAK
(Pb−Free)
75 Units / Rail
2500 Units / Reel
TO−220
TO−220
(Pb−Free)
50 Units / Rail
DPAK
DPAK
(Pb−Free)
75 Units / Rail
DPAK
DPAK
(Pb−Free)
2500 Units / Reel
TO−220
TO−220
(Pb−Free)
50 Units / Rail
DPAK
DPAK
(Pb−Free)
75 Units / Rail
DPAK
DPAK
(Pb−Free)
2500 Units / Reel
TO−220
TO−220
(Pb−Free)
50 Units / Rail
DPAK
DPAK
(Pb−Free)
75 Units / Rail
DPAK
DPAK
(Pb−Free)
2500 Units / Reel
TO−220
TO−220
(Pb−Free)
50 Units / Rail
75 Units / Rail
2500 Units / Reel
50 Units / Rail
75 Units / Rail
2500 Units / Reel
50 Units / Rail
2500 Units / Reel
50 Units / Rail
75 Units / Rail
2500 Units / Reel
50 Units / Rail
75 Units / Rail
2500 Units / Reel
50 Units / Rail
75 Units / Rail
2500 Units / Reel
50 Units / Rail
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
5
MC79M00 Series
ORDERING INFORMATION
Device
Output Voltage
Tolerance
Operating
Temperature Range
MC79M15BDT
MC79M15BDTG
MC79M15BDTRK
TJ = −40°C to +125°C
MC79M15BDTRKG
MC79M15BT
MC79M15BTG
MC79M15CDT
4.0%
MC79M15CDTG
MC79M15CDTRK
MC79M15CDTRKG
TJ = 0°C to +125°C
MC79M15CT
MC79M15CTG
Package
Shipping[
DPAK
DPAK
(Pb−Free)
75 Units / Rail
DPAK
DPAK
(Pb−Free)
2500 Units / Reel
TO−220
TO−220
(Pb−Free)
50 Units / Rail
DPAK
DPAK
(Pb−Free)
75 Units / Rail
DPAK
DPAK
(Pb−Free)
2500 Units / Reel
TO−220
TO−220
(Pb−Free)
50 Units / Rail
75 Units / Rail
2500 Units / Reel
50 Units / Rail
75 Units / Rail
2500 Units / Reel
50 Units / Rail
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
6
MC79M00 Series
PACKAGE DIMENSIONS
TO−220, SINGLE GAUGE
T SUFFIX
CASE 221AB−01
ISSUE O
−T−
B
SEATING
PLANE
C
F
T
S
4
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
A
Q
1 2 3
U
H
K
Z
L
R
V
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
J
G
D
N
http://onsemi.com
7
INCHES
MIN
MAX
0.570
0.620
0.380
0.405
0.160
0.190
0.025
0.035
0.142
0.147
0.095
0.105
0.110
0.155
0.018
0.025
0.500
0.562
0.045
0.060
0.190
0.210
0.100
0.120
0.080
0.110
0.020
0.055
0.235
0.255
0.000
0.050
0.045
−−−
−−−
0.080
MILLIMETERS
MIN
MAX
14.48
15.75
9.66
10.28
4.07
4.82
0.64
0.88
3.61
3.73
2.42
2.66
2.80
3.93
0.46
0.64
12.70
14.27
1.15
1.52
4.83
5.33
2.54
3.04
2.04
2.79
0.508
1.39
5.97
6.47
0.00
1.27
1.15
−−−
−−−
2.04
MC79M00 Series
PACKAGE DIMENSIONS
DPAK−3
DT SUFFIX
CASE 369C−01
ISSUE O
−T−
C
B
V
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
SEATING
PLANE
E
R
4
Z
A
S
1
2
DIM
A
B
C
D
E
F
G
H
J
K
L
R
S
U
V
Z
3
U
K
F
J
L
H
D
G
2 PL
0.13 (0.005)
M
INCHES
MIN
MAX
0.235 0.245
0.250 0.265
0.086 0.094
0.027 0.035
0.018 0.023
0.037 0.045
0.180 BSC
0.034 0.040
0.018 0.023
0.102 0.114
0.090 BSC
0.180 0.215
0.025 0.040
0.020
−−−
0.035 0.050
0.155
−−−
MILLIMETERS
MIN
MAX
5.97
6.22
6.35
6.73
2.19
2.38
0.69
0.88
0.46
0.58
0.94
1.14
4.58 BSC
0.87
1.01
0.46
0.58
2.60
2.89
2.29 BSC
4.57
5.45
0.63
1.01
0.51
−−−
0.89
1.27
3.93
−−−
T
SOLDERING FOOTPRINT*
6.20
0.244
3.0
0.118
2.58
0.101
5.80
0.228
1.6
0.063
6.172
0.243
SCALE 3:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
8
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC79M00/D